You are not logged in.

#1 2024-08-28 04:09:41

FungiKin
Member
From: USA, North America, Earth
Registered: 2023-03-30
Posts: 8

[SOLVED] Native Instruments Audio 8 DJ/snd_usb_caiaq stopped working

Hello, there I've been trying the past three days to get my NI Audio 8 DJ working under arch linux again, as it stopped working when I plugged it back in the morning after i updated my arch linux installation.
What I have tried (none of which worked):
Downgrading pipewire, wireplumber, and related packages
Using linux-lts
Installing all of the alsa/sound related firmware modules
Putting snd_usb_caiaq in a modules-load.d file
The modprobe stuff the alsa wiki suggests doing

"dmesg | tail" after unplugging and reinserting USB cable:

usb 1-1.1.2: USB disconnect, device number 7
usb 1-1.1.2: new high-speed USB device number 13 using xhci_hcd
usb 1-1.1.2: language id specifier not provided by device, defaulting to English
usb 1-1.1.2: New USB device found, idVendor=17cc, idProduct=1978, bcdDevice= 0.0e
usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
usb 1-1.1.2: Product: Audio 8 DJ
usb 1-1.1.2: Manufacturer: Native Instruments
usb 1-1.1.2: SerialNumber: SN-H3KG25C3X4   
usb 1-1.1.2: received EP1 urb->status = -2
usb 1-1.1.2: unable to init card! (ret=-19)

full dmesg:

[    0.000000] Linux version 6.10.6-zen1-1-zen (linux-zen@archlinux) (gcc (GCC) 14.2.1 20240805, GNU ld (GNU Binutils) 2.43.0) #1 ZEN SMP PREEMPT_DYNAMIC Mon, 19 Aug 2024 17:02:05 +0000
[    0.000000] Command line: rw root=UUID=91ae5638-1608-41e0-bf5f-c3c1aecb7801 zswap.enabled=0 i915.enable_psr=0 initrd=/intel-ucode.img initrd=/initramfs-linux-zen.img initrd=/initramfs-linux.img initrd=/initramfs-linux-lts.img initrd=/initramfs-linux-rt.img
[    0.000000] BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009efff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009f000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x0000000071896fff] usable
[    0.000000] BIOS-e820: [mem 0x0000000071897000-0x0000000072996fff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000072997000-0x0000000088badfff] usable
[    0.000000] BIOS-e820: [mem 0x0000000088bae000-0x000000008959dfff] reserved
[    0.000000] BIOS-e820: [mem 0x000000008959e000-0x0000000089c8dfff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x0000000089c8e000-0x0000000089d0dfff] ACPI data
[    0.000000] BIOS-e820: [mem 0x0000000089d0e000-0x0000000089d0efff] usable
[    0.000000] BIOS-e820: [mem 0x0000000089d0f000-0x000000008f7fffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fe000000-0x00000000fe010fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed10000-0x00000000fed19fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed84000-0x00000000fed84fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ff600000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000046e7fffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] APIC: Static calls initialized
[    0.000000] e820: update [mem 0x6e435018-0x6e45e657] usable ==> usable
[    0.000000] e820: update [mem 0x6e424018-0x6e434057] usable ==> usable
[    0.000000] extended physical RAM map:
[    0.000000] reserve setup_data: [mem 0x0000000000000000-0x000000000009efff] usable
[    0.000000] reserve setup_data: [mem 0x000000000009f000-0x00000000000fffff] reserved
[    0.000000] reserve setup_data: [mem 0x0000000000100000-0x000000006e424017] usable
[    0.000000] reserve setup_data: [mem 0x000000006e424018-0x000000006e434057] usable
[    0.000000] reserve setup_data: [mem 0x000000006e434058-0x000000006e435017] usable
[    0.000000] reserve setup_data: [mem 0x000000006e435018-0x000000006e45e657] usable
[    0.000000] reserve setup_data: [mem 0x000000006e45e658-0x0000000071896fff] usable
[    0.000000] reserve setup_data: [mem 0x0000000071897000-0x0000000072996fff] reserved
[    0.000000] reserve setup_data: [mem 0x0000000072997000-0x0000000088badfff] usable
[    0.000000] reserve setup_data: [mem 0x0000000088bae000-0x000000008959dfff] reserved
[    0.000000] reserve setup_data: [mem 0x000000008959e000-0x0000000089c8dfff] ACPI NVS
[    0.000000] reserve setup_data: [mem 0x0000000089c8e000-0x0000000089d0dfff] ACPI data
[    0.000000] reserve setup_data: [mem 0x0000000089d0e000-0x0000000089d0efff] usable
[    0.000000] reserve setup_data: [mem 0x0000000089d0f000-0x000000008f7fffff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000fe000000-0x00000000fe010fff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000fed10000-0x00000000fed19fff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000fed84000-0x00000000fed84fff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000ff600000-0x00000000ffffffff] reserved
[    0.000000] reserve setup_data: [mem 0x0000000100000000-0x000000046e7fffff] usable
[    0.000000] efi: EFI v2.6 by INSYDE Corp.
[    0.000000] efi: TPMFinalLog=0x89596000 ACPI 2.0=0x89d0d014 ESRT=0x88dce618 SMBIOS=0x88dca000 SMBIOS 3.0=0x88dc8000 MEMATTR=0x78a93018 INITRD=0x729acc18 RNG=0x89cab018 TPMEventLog=0x729a3018 
[    0.000000] random: crng init done
[    0.000000] efi: Remove mem47: MMIO range=[0xe0000000-0xefffffff] (256MB) from e820 map
[    0.000000] e820: remove [mem 0xe0000000-0xefffffff] reserved
[    0.000000] efi: Not removing mem48: MMIO range=[0xfe000000-0xfe010fff] (68KB) from e820 map
[    0.000000] efi: Not removing mem49: MMIO range=[0xfed10000-0xfed19fff] (40KB) from e820 map
[    0.000000] efi: Not removing mem50: MMIO range=[0xfed84000-0xfed84fff] (4KB) from e820 map
[    0.000000] efi: Not removing mem51: MMIO range=[0xfee00000-0xfee00fff] (4KB) from e820 map
[    0.000000] efi: Remove mem52: MMIO range=[0xff600000-0xffffffff] (10MB) from e820 map
[    0.000000] e820: remove [mem 0xff600000-0xffffffff] reserved
[    0.000000] SMBIOS 3.0.1 present.
[    0.000000] DMI: Acer Nitro AN515-53/Freed_CFS, BIOS V1.28 08/05/2019
[    0.000000] DMI: Memory slots populated: 2/2
[    0.000000] tsc: Detected 2300.000 MHz processor
[    0.000000] tsc: Detected 2299.968 MHz TSC
[    0.000006] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000008] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000014] last_pfn = 0x46e800 max_arch_pfn = 0x400000000
[    0.000017] MTRR map: 4 entries (3 fixed + 1 variable; max 23), built from 10 variable MTRRs
[    0.000019] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT  
[    0.000318] last_pfn = 0x89d0f max_arch_pfn = 0x400000000
[    0.006205] esrt: Reserving ESRT space from 0x0000000088dce618 to 0x0000000088dce650.
[    0.006211] Using GB pages for direct mapping
[    0.006468] Secure boot disabled
[    0.006469] RAMDISK: [mem 0x1d513000-0x39b5dfff]
[    0.006502] ACPI: Early table checksum verification disabled
[    0.006504] ACPI: RSDP 0x0000000089D0D014 000024 (v02 ACRSYS)
[    0.006507] ACPI: XSDT 0x0000000089CEE188 0000F4 (v01 ACRSYS ACRPRDCT 00000000      01000013)
[    0.006512] ACPI: FACP 0x0000000089CF0000 00010C (v05 ACRSYS ACRPRDCT 00000000 1025 00040000)
[    0.006516] ACPI: DSDT 0x0000000089CB3000 0373CB (v02 ACRSYS ACRPRDCT 00000000 1025 00040000)
[    0.006518] ACPI: FACS 0x0000000089C2D000 000040
[    0.006520] ACPI: UEFI 0x0000000089D0C000 000236 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.006523] ACPI: SSDT 0x0000000089D0A000 0017D5 (v02 ACRSYS ACRPRDCT 00003000 1025 00040000)
[    0.006525] ACPI: SSDT 0x0000000089D06000 0031C7 (v02 ACRSYS ACRPRDCT 00003000 1025 00040000)
[    0.006527] ACPI: SSDT 0x0000000089D04000 001DC8 (v02 ACRSYS ACRPRDCT 00001000 1025 00040000)
[    0.006530] ACPI: UEFI 0x0000000089D03000 000042 (v01 ACRSYS ACRPRDCT 00000002 1025 00040000)
[    0.006532] ACPI: SSDT 0x0000000089D02000 00045A (v02 ACRSYS ACRPRDCT 00001000 1025 00040000)
[    0.006534] ACPI: SSDT 0x0000000089D01000 000046 (v02 ACRSYS ACRPRDCT 00003000 1025 00040000)
[    0.006536] ACPI: TPM2 0x0000000089D00000 000034 (v03 ACRSYS ACRPRDCT 00000002 1025 00040000)
[    0.006539] ACPI: LPIT 0x0000000089CFF000 00005C (v01 ACRSYS ACRPRDCT 00000000 1025 00040000)
[    0.006541] ACPI: WSMT 0x0000000089CFE000 000028 (v01 ACRSYS ACRPRDCT 00000000 1025 00040000)
[    0.006543] ACPI: SSDT 0x0000000089CFD000 000C2F (v02 ACRSYS ACRPRDCT 00001000 1025 00040000)
[    0.006545] ACPI: SSDT 0x0000000089CFC000 000FBB (v02 ACRSYS ACRPRDCT 00000000 1025 00040000)
[    0.006548] ACPI: DBGP 0x0000000089CFB000 000034 (v01 ACRSYS ACRPRDCT 00000002 1025 00040000)
[    0.006550] ACPI: DBG2 0x0000000089CFA000 000054 (v00 ACRSYS ACRPRDCT 00000002 1025 00040000)
[    0.006552] ACPI: SSDT 0x0000000089CF9000 000B74 (v02 ACRSYS ACRPRDCT 00001000 1025 00040000)
[    0.006554] ACPI: SSDT 0x0000000089CF3000 0058C1 (v01 ACRSYS ACRPRDCT 00001000 1025 00040000)
[    0.006557] ACPI: MSDM 0x0000000089CF2000 000055 (v03 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.006559] ACPI: ASF! 0x0000000089CF1000 0000A5 (v32 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.006561] ACPI: HPET 0x0000000089CEF000 000038 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.006563] ACPI: APIC 0x0000000089CED000 00012C (v03 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.006566] ACPI: MCFG 0x0000000089CEC000 00003C (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.006568] ACPI: SSDT 0x0000000089CAE000 0044DC (v01 ACRSYS ACRPRDCT 00001000 1025 00040000)
[    0.006570] ACPI: DMAR 0x0000000089CEB000 0000A8 (v01 ACRSYS ACRPRDCT 00000002 1025 00040000)
[    0.006572] ACPI: FPDT 0x0000000089CAD000 000044 (v01 ACRSYS ACRPRDCT 00000002 1025 00040000)
[    0.006575] ACPI: BGRT 0x0000000089CAC000 000038 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.006576] ACPI: Reserving FACP table memory at [mem 0x89cf0000-0x89cf010b]
[    0.006577] ACPI: Reserving DSDT table memory at [mem 0x89cb3000-0x89cea3ca]
[    0.006578] ACPI: Reserving FACS table memory at [mem 0x89c2d000-0x89c2d03f]
[    0.006579] ACPI: Reserving UEFI table memory at [mem 0x89d0c000-0x89d0c235]
[    0.006579] ACPI: Reserving SSDT table memory at [mem 0x89d0a000-0x89d0b7d4]
[    0.006580] ACPI: Reserving SSDT table memory at [mem 0x89d06000-0x89d091c6]
[    0.006581] ACPI: Reserving SSDT table memory at [mem 0x89d04000-0x89d05dc7]
[    0.006581] ACPI: Reserving UEFI table memory at [mem 0x89d03000-0x89d03041]
[    0.006582] ACPI: Reserving SSDT table memory at [mem 0x89d02000-0x89d02459]
[    0.006582] ACPI: Reserving SSDT table memory at [mem 0x89d01000-0x89d01045]
[    0.006583] ACPI: Reserving TPM2 table memory at [mem 0x89d00000-0x89d00033]
[    0.006584] ACPI: Reserving LPIT table memory at [mem 0x89cff000-0x89cff05b]
[    0.006584] ACPI: Reserving WSMT table memory at [mem 0x89cfe000-0x89cfe027]
[    0.006585] ACPI: Reserving SSDT table memory at [mem 0x89cfd000-0x89cfdc2e]
[    0.006585] ACPI: Reserving SSDT table memory at [mem 0x89cfc000-0x89cfcfba]
[    0.006586] ACPI: Reserving DBGP table memory at [mem 0x89cfb000-0x89cfb033]
[    0.006587] ACPI: Reserving DBG2 table memory at [mem 0x89cfa000-0x89cfa053]
[    0.006587] ACPI: Reserving SSDT table memory at [mem 0x89cf9000-0x89cf9b73]
[    0.006588] ACPI: Reserving SSDT table memory at [mem 0x89cf3000-0x89cf88c0]
[    0.006588] ACPI: Reserving MSDM table memory at [mem 0x89cf2000-0x89cf2054]
[    0.006589] ACPI: Reserving ASF! table memory at [mem 0x89cf1000-0x89cf10a4]
[    0.006590] ACPI: Reserving HPET table memory at [mem 0x89cef000-0x89cef037]
[    0.006590] ACPI: Reserving APIC table memory at [mem 0x89ced000-0x89ced12b]
[    0.006591] ACPI: Reserving MCFG table memory at [mem 0x89cec000-0x89cec03b]
[    0.006591] ACPI: Reserving SSDT table memory at [mem 0x89cae000-0x89cb24db]
[    0.006592] ACPI: Reserving DMAR table memory at [mem 0x89ceb000-0x89ceb0a7]
[    0.006593] ACPI: Reserving FPDT table memory at [mem 0x89cad000-0x89cad043]
[    0.006593] ACPI: Reserving BGRT table memory at [mem 0x89cac000-0x89cac037]
[    0.006877] No NUMA configuration found
[    0.006878] Faking a node at [mem 0x0000000000000000-0x000000046e7fffff]
[    0.006880] NODE_DATA(0) allocated [mem 0x46e7fb000-0x46e7fffff]
[    0.006901] Zone ranges:
[    0.006902]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.006903]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
[    0.006905]   Normal   [mem 0x0000000100000000-0x000000046e7fffff]
[    0.006906]   Device   empty
[    0.006906] Movable zone start for each node
[    0.006907] Early memory node ranges
[    0.006907]   node   0: [mem 0x0000000000001000-0x000000000009efff]
[    0.006908]   node   0: [mem 0x0000000000100000-0x0000000071896fff]
[    0.006909]   node   0: [mem 0x0000000072997000-0x0000000088badfff]
[    0.006910]   node   0: [mem 0x0000000089d0e000-0x0000000089d0efff]
[    0.006911]   node   0: [mem 0x0000000100000000-0x000000046e7fffff]
[    0.006913] Initmem setup node 0 [mem 0x0000000000001000-0x000000046e7fffff]
[    0.006916] On node 0, zone DMA: 1 pages in unavailable ranges
[    0.006942] On node 0, zone DMA: 97 pages in unavailable ranges
[    0.009551] On node 0, zone DMA32: 4352 pages in unavailable ranges
[    0.009594] On node 0, zone DMA32: 4448 pages in unavailable ranges
[    0.026706] On node 0, zone Normal: 25329 pages in unavailable ranges
[    0.026766] On node 0, zone Normal: 6144 pages in unavailable ranges
[    0.026791] Reserving Intel graphics memory at [mem 0x8b800000-0x8f7fffff]
[    0.027782] ACPI: PM-Timer IO Port: 0x1808
[    0.027788] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.027789] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[    0.027790] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[    0.027791] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[    0.027791] ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
[    0.027792] ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
[    0.027792] ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
[    0.027793] ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1])
[    0.027793] ACPI: LAPIC_NMI (acpi_id[0x09] high edge lint[0x1])
[    0.027794] ACPI: LAPIC_NMI (acpi_id[0x0a] high edge lint[0x1])
[    0.027795] ACPI: LAPIC_NMI (acpi_id[0x0b] high edge lint[0x1])
[    0.027795] ACPI: LAPIC_NMI (acpi_id[0x0c] high edge lint[0x1])
[    0.027796] ACPI: LAPIC_NMI (acpi_id[0x0d] high edge lint[0x1])
[    0.027796] ACPI: LAPIC_NMI (acpi_id[0x0e] high edge lint[0x1])
[    0.027797] ACPI: LAPIC_NMI (acpi_id[0x0f] high edge lint[0x1])
[    0.027797] ACPI: LAPIC_NMI (acpi_id[0x10] high edge lint[0x1])
[    0.027855] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-119
[    0.027857] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.027859] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.027862] ACPI: Using ACPI (MADT) for SMP configuration information
[    0.027863] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.027868] e820: update [mem 0x78b81000-0x78c74fff] usable ==> reserved
[    0.027876] TSC deadline timer available
[    0.027880] CPU topo: Max. logical packages:   1
[    0.027880] CPU topo: Max. logical dies:       1
[    0.027881] CPU topo: Max. dies per package:   1
[    0.027884] CPU topo: Max. threads per core:   2
[    0.027885] CPU topo: Num. cores per package:     4
[    0.027885] CPU topo: Num. threads per package:   8
[    0.027886] CPU topo: Allowing 8 present CPUs plus 0 hotplug CPUs
[    0.027896] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.027898] PM: hibernation: Registered nosave memory: [mem 0x0009f000-0x000fffff]
[    0.027899] PM: hibernation: Registered nosave memory: [mem 0x6e424000-0x6e424fff]
[    0.027900] PM: hibernation: Registered nosave memory: [mem 0x6e434000-0x6e434fff]
[    0.027901] PM: hibernation: Registered nosave memory: [mem 0x6e435000-0x6e435fff]
[    0.027902] PM: hibernation: Registered nosave memory: [mem 0x6e45e000-0x6e45efff]
[    0.027903] PM: hibernation: Registered nosave memory: [mem 0x71897000-0x72996fff]
[    0.027904] PM: hibernation: Registered nosave memory: [mem 0x78b81000-0x78c74fff]
[    0.027906] PM: hibernation: Registered nosave memory: [mem 0x88bae000-0x8959dfff]
[    0.027906] PM: hibernation: Registered nosave memory: [mem 0x8959e000-0x89c8dfff]
[    0.027907] PM: hibernation: Registered nosave memory: [mem 0x89c8e000-0x89d0dfff]
[    0.027908] PM: hibernation: Registered nosave memory: [mem 0x89d0f000-0x8f7fffff]
[    0.027908] PM: hibernation: Registered nosave memory: [mem 0x8f800000-0xfdffffff]
[    0.027909] PM: hibernation: Registered nosave memory: [mem 0xfe000000-0xfe010fff]
[    0.027909] PM: hibernation: Registered nosave memory: [mem 0xfe011000-0xfed0ffff]
[    0.027910] PM: hibernation: Registered nosave memory: [mem 0xfed10000-0xfed19fff]
[    0.027910] PM: hibernation: Registered nosave memory: [mem 0xfed1a000-0xfed83fff]
[    0.027911] PM: hibernation: Registered nosave memory: [mem 0xfed84000-0xfed84fff]
[    0.027911] PM: hibernation: Registered nosave memory: [mem 0xfed85000-0xfedfffff]
[    0.027912] PM: hibernation: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[    0.027912] PM: hibernation: Registered nosave memory: [mem 0xfee01000-0xffffffff]
[    0.027913] [mem 0x8f800000-0xfdffffff] available for PCI devices
[    0.027914] Booting paravirtualized kernel on bare hardware
[    0.027916] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns
[    0.032712] setup_percpu: NR_CPUS:320 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1
[    0.033069] percpu: Embedded 66 pages/cpu s233472 r8192 d28672 u524288
[    0.033074] pcpu-alloc: s233472 r8192 d28672 u524288 alloc=1*2097152
[    0.033076] pcpu-alloc: [0] 0 1 2 3 [0] 4 5 6 7 
[    0.033089] Kernel command line: rw root=UUID=91ae5638-1608-41e0-bf5f-c3c1aecb7801 zswap.enabled=0 i915.enable_psr=0 initrd=/intel-ucode.img initrd=/initramfs-linux-zen.img initrd=/initramfs-linux.img initrd=/initramfs-linux-lts.img initrd=/initramfs-linux-rt.img
[    0.034282] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear)
[    0.034829] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[    0.034922] Fallback order for Node 0: 0 
[    0.034924] Built 1 zonelists, mobility grouping on.  Total pages: 4153933
[    0.034925] Policy zone: Normal
[    0.035084] mem auto-init: stack:all(zero), heap alloc:on, heap free:off
[    0.035092] software IO TLB: area num 8.
[    0.069390] Memory: 15646596K/16615732K available (20480K kernel code, 2197K rwdata, 13284K rodata, 3564K init, 3180K bss, 968876K reserved, 0K cma-reserved)
[    0.069558] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.069576] Kernel/User page tables isolation: enabled
[    0.069601] ftrace: allocating 48073 entries in 188 pages
[    0.075744] ftrace: allocated 188 pages with 5 groups
[    0.075797] Dynamic Preempt: full
[    0.075830] rcu: Preemptible hierarchical RCU implementation.
[    0.075831] rcu: 	RCU restricting CPUs from NR_CPUS=320 to nr_cpu_ids=8.
[    0.075832] rcu: 	RCU priority boosting: priority 1 delay 500 ms.
[    0.075832] 	Trampoline variant of Tasks RCU enabled.
[    0.075833] 	Rude variant of Tasks RCU enabled.
[    0.075833] 	Tracing variant of Tasks RCU enabled.
[    0.075834] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies.
[    0.075834] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[    0.075839] RCU Tasks: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1.
[    0.075840] RCU Tasks Rude: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1.
[    0.075841] RCU Tasks Trace: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1.
[    0.079066] NR_IRQS: 20736, nr_irqs: 2048, preallocated irqs: 16
[    0.079378] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.079769] kfence: initialized - using 2097152 bytes for 255 objects at 0x(____ptrval____)-0x(____ptrval____)
[    0.079794] Console: colour dummy device 80x25
[    0.079795] printk: legacy console [tty0] enabled
[    0.079831] ACPI: Core revision 20240322
[    0.080190] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635855245 ns
[    0.080356] APIC: Switch to symmetric I/O mode setup
[    0.080358] DMAR: Host address width 39
[    0.080359] DMAR: DRHD base: 0x000000fed90000 flags: 0x0
[    0.080363] DMAR: dmar0: reg_base_addr fed90000 ver 1:0 cap 1c0000c40660462 ecap 19e2ff0505e
[    0.080365] DMAR: DRHD base: 0x000000fed91000 flags: 0x1
[    0.080368] DMAR: dmar1: reg_base_addr fed91000 ver 1:0 cap d2008c40660462 ecap f050da
[    0.080370] DMAR: RMRR base: 0x00000089575000 end: 0x00000089594fff
[    0.080386] DMAR: RMRR base: 0x0000008b000000 end: 0x0000008f7fffff
[    0.080388] DMAR-IR: IOAPIC id 2 under DRHD base  0xfed91000 IOMMU 1
[    0.080389] DMAR-IR: HPET id 0 under DRHD base 0xfed91000
[    0.080390] DMAR-IR: Queued invalidation will be enabled to support x2apic and Intr-remapping.
[    0.083804] DMAR-IR: Enabled IRQ remapping in x2apic mode
[    0.083805] x2apic enabled
[    0.083863] APIC: Switched APIC routing to: cluster x2apic
[    0.093306] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.098315] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x212717146a7, max_idle_ns: 440795291431 ns
[    0.098319] Calibrating delay loop (skipped), value calculated using timer frequency.. 4599.93 BogoMIPS (lpj=2299968)
[    0.098335] x86/cpu: SGX disabled by BIOS.
[    0.098341] CPU0: Thermal monitoring enabled (TM1)
[    0.098376] Last level iTLB entries: 4KB 64, 2MB 8, 4MB 8
[    0.098377] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0, 1GB 4
[    0.098380] process: using mwait in idle threads
[    0.098382] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[    0.098384] Spectre V2 : Mitigation: IBRS
[    0.098384] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[    0.098385] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT
[    0.098386] RETBleed: Mitigation: IBRS
[    0.098387] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier
[    0.098388] Spectre V2 : User space: Mitigation: STIBP via prctl
[    0.098389] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl
[    0.098394] MDS: Mitigation: Clear CPU buffers
[    0.098394] MMIO Stale Data: Mitigation: Clear CPU buffers
[    0.098397] SRBDS: Mitigation: Microcode
[    0.098401] GDS: Mitigation: Microcode
[    0.098405] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[    0.098406] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[    0.098407] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[    0.098408] x86/fpu: Supporting XSAVE feature 0x008: 'MPX bounds registers'
[    0.098409] x86/fpu: Supporting XSAVE feature 0x010: 'MPX CSR'
[    0.098410] x86/fpu: xstate_offset[2]:  576, xstate_sizes[2]:  256
[    0.098411] x86/fpu: xstate_offset[3]:  832, xstate_sizes[3]:   64
[    0.098413] x86/fpu: xstate_offset[4]:  896, xstate_sizes[4]:   64
[    0.098414] x86/fpu: Enabled xstate features 0x1f, context size is 960 bytes, using 'compacted' format.
[    0.122592] Freeing SMP alternatives memory: 52K
[    0.122594] pid_max: default: 32768 minimum: 301
[    0.125358] LSM: initializing lsm=capability,landlock,lockdown,yama,bpf
[    0.125377] landlock: Up and running.
[    0.125379] Yama: becoming mindful.
[    0.125383] LSM support for eBPF active
[    0.125414] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.125426] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.126400] smpboot: CPU0: Intel(R) Core(TM) i5-8300H CPU @ 2.30GHz (family: 0x6, model: 0x9e, stepping: 0xa)
[    0.126546] Performance Events: PEBS fmt3+, Skylake events, 32-deep LBR, full-width counters, Intel PMU driver.
[    0.126568] ... version:                4
[    0.126569] ... bit width:              48
[    0.126569] ... generic registers:      4
[    0.126570] ... value mask:             0000ffffffffffff
[    0.126571] ... max period:             00007fffffffffff
[    0.126572] ... fixed-purpose events:   3
[    0.126572] ... event mask:             000000070000000f
[    0.126660] signal: max sigframe size: 2032
[    0.126674] Estimated ratio of average max frequency by base frequency (times 1024): 1736
[    0.127455] rcu: Hierarchical SRCU implementation.
[    0.127456] rcu: 	Max phase no-delay instances is 400.
[    0.127980] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[    0.128039] smp: Bringing up secondary CPUs ...
[    0.128104] smpboot: x86: Booting SMP configuration:
[    0.128105] .... node  #0, CPUs:      #1 #2 #3 #4 #5 #6 #7
[    0.131441] MDS CPU bug present and SMT on, data leak possible. See https://www.kernel.org/doc/html/latest/admin-guide/hw-vuln/mds.html for more details.
[    0.131441] MMIO Stale Data CPU bug present and SMT on, data leak possible. See https://www.kernel.org/doc/html/latest/admin-guide/hw-vuln/processor_mmio_stale_data.html for more details.
[    0.131441] smp: Brought up 1 node, 8 CPUs
[    0.131441] smpboot: Total of 8 processors activated (36799.48 BogoMIPS)
[    0.132714] devtmpfs: initialized
[    0.132714] x86/mm: Memory block size: 128MB
[    0.133889] ACPI: PM: Registering ACPI NVS region [mem 0x8959e000-0x89c8dfff] (7274496 bytes)
[    0.133889] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[    0.133889] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[    0.133889] pinctrl core: initialized pinctrl subsystem
[    0.134319] PM: RTC time: 03:27:23, date: 2024-08-28
[    0.134670] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.134874] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations
[    0.134957] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.135048] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.135056] audit: initializing netlink subsys (disabled)
[    0.135060] audit: type=2000 audit(1724815643.045:1): state=initialized audit_enabled=0 res=1
[    0.135060] thermal_sys: Registered thermal governor 'fair_share'
[    0.135060] thermal_sys: Registered thermal governor 'bang_bang'
[    0.135060] thermal_sys: Registered thermal governor 'step_wise'
[    0.135060] thermal_sys: Registered thermal governor 'user_space'
[    0.135060] thermal_sys: Registered thermal governor 'power_allocator'
[    0.135105] cpuidle: using governor ladder
[    0.135105] cpuidle: using governor menu
[    0.135105] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.135105] PCI: ECAM [mem 0xe0000000-0xefffffff] (base 0xe0000000) for domain 0000 [bus 00-ff]
[    0.135105] PCI: Using configuration type 1 for base access
[    0.135346] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible.
[    0.135984] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages
[    0.135984] HugeTLB: 16380 KiB vmemmap can be freed for a 1.00 GiB page
[    0.135984] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
[    0.135984] HugeTLB: 28 KiB vmemmap can be freed for a 2.00 MiB page
[    0.136352] Demotion targets for Node 0: null
[    0.136389] fbcon: Taking over console
[    0.136408] ACPI: Added _OSI(Module Device)
[    0.136409] ACPI: Added _OSI(Processor Device)
[    0.136411] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.136412] ACPI: Added _OSI(Processor Aggregator Device)
[    0.180246] ACPI: 11 ACPI AML tables successfully acquired and loaded
[    0.186796] ACPI: Dynamic OEM Table Load:
[    0.186803] ACPI: SSDT 0xFFFF954D810C7000 000400 (v02 PmRef  Cpu0Cst  00003001 INTL 20160422)
[    0.187261] ACPI: Dynamic OEM Table Load:
[    0.187266] ACPI: SSDT 0xFFFF954D810D0800 0005DF (v02 PmRef  Cpu0Ist  00003000 INTL 20160422)
[    0.188474] ACPI: Dynamic OEM Table Load:
[    0.188478] ACPI: SSDT 0xFFFF954D81989A00 00010A (v02 PmRef  Cpu0Hwp  00003000 INTL 20160422)
[    0.189526] ACPI: Dynamic OEM Table Load:
[    0.189531] ACPI: SSDT 0xFFFF954D810D4800 000724 (v02 PmRef  HwpLvt   00003000 INTL 20160422)
[    0.190918] ACPI: Dynamic OEM Table Load:
[    0.190924] ACPI: SSDT 0xFFFF954D810CE000 000EF1 (v02 PmRef  ApIst    00003000 INTL 20160422)
[    0.192787] ACPI: Dynamic OEM Table Load:
[    0.192792] ACPI: SSDT 0xFFFF954D810C4800 000317 (v02 PmRef  ApHwp    00003000 INTL 20160422)
[    0.193906] ACPI: Dynamic OEM Table Load:
[    0.193910] ACPI: SSDT 0xFFFF954D810C1000 00030A (v02 PmRef  ApCst    00003000 INTL 20160422)
[    0.198001] ACPI: _OSC evaluated successfully for all CPUs
[    0.198269] ACPI: EC: EC started
[    0.198270] ACPI: EC: interrupt blocked
[    0.199842] ACPI: EC: EC_CMD/EC_SC=0x66, EC_DATA=0x62
[    0.199844] ACPI: \_SB_.PCI0.LPCB.EC0_: Boot DSDT EC used to handle transactions
[    0.199845] ACPI: Interpreter enabled
[    0.199878] ACPI: PM: (supports S0 S3 S4 S5)
[    0.199879] ACPI: Using IOAPIC for interrupt routing
[    0.201217] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.201218] PCI: Using E820 reservations for host bridge windows
[    0.202819] ACPI: Enabled 6 GPEs in block 00 to 7F
[    0.203777] ACPI: \_SB_.PCI0.PEG0.PG00: New power resource
[    0.204284] ACPI: \_SB_.PCI0.PEG1.PG01: New power resource
[    0.204618] ACPI: \_SB_.PCI0.PEG2.PG02: New power resource
[    0.209706] ACPI: \_SB_.PCI0.XDCI.USBC: New power resource
[    0.216416] ACPI: \_SB_.PCI0.SAT0.VOL0.V0PR: New power resource
[    0.216592] ACPI: \_SB_.PCI0.SAT0.VOL1.V1PR: New power resource
[    0.216763] ACPI: \_SB_.PCI0.SAT0.VOL2.V2PR: New power resource
[    0.228889] ACPI: \_SB_.PCI0.CNVW.WRST: New power resource
[    0.229196] acpi ABCD0000:00: ACPI dock station (docks/bays count: 1)
[    0.233625] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe])
[    0.233631] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI EDR HPX-Type3]
[    0.238866] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug SHPCHotplug PME AER PCIeCapability LTR DPC]
[    0.241571] PCI host bridge to bus 0000:00
[    0.241573] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.241575] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.241576] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.241577] pci_bus 0000:00: root bus resource [mem 0x8f800000-0xdfffffff window]
[    0.241578] pci_bus 0000:00: root bus resource [mem 0xfc800000-0xfe7fffff window]
[    0.241580] pci_bus 0000:00: root bus resource [bus 00-fe]
[    0.241657] pci 0000:00:00.0: [8086:3e10] type 00 class 0x060000 conventional PCI endpoint
[    0.241716] pci 0000:00:01.0: [8086:1901] type 01 class 0x060400 PCIe Root Port
[    0.241726] pci 0000:00:01.0: PCI bridge to [bus 01-05]
[    0.241729] pci 0000:00:01.0:   bridge window [io  0x4000-0x4fff]
[    0.241731] pci 0000:00:01.0:   bridge window [mem 0xa3000000-0xa40fffff]
[    0.241735] pci 0000:00:01.0:   bridge window [mem 0x90000000-0xa1ffffff 64bit pref]
[    0.241757] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.241891] pci 0000:00:02.0: [8086:3e9b] type 00 class 0x030000 PCIe Root Complex Integrated Endpoint
[    0.241898] pci 0000:00:02.0: BAR 0 [mem 0xa2000000-0xa2ffffff 64bit]
[    0.241902] pci 0000:00:02.0: BAR 2 [mem 0xb0000000-0xbfffffff 64bit pref]
[    0.241905] pci 0000:00:02.0: BAR 4 [io  0x5000-0x503f]
[    0.241919] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.242116] pci 0000:00:08.0: [8086:1911] type 00 class 0x088000 conventional PCI endpoint
[    0.242123] pci 0000:00:08.0: BAR 0 [mem 0xa441c000-0xa441cfff 64bit]
[    0.242272] pci 0000:00:12.0: [8086:a379] type 00 class 0x118000 conventional PCI endpoint
[    0.242299] pci 0000:00:12.0: BAR 0 [mem 0xa441d000-0xa441dfff 64bit]
[    0.242518] pci 0000:00:14.0: [8086:a36d] type 00 class 0x0c0330 conventional PCI endpoint
[    0.242543] pci 0000:00:14.0: BAR 0 [mem 0xa4400000-0xa440ffff 64bit]
[    0.242645] pci 0000:00:14.0: PME# supported from D3hot D3cold
[    0.243010] pci 0000:00:14.2: [8086:a36f] type 00 class 0x050000 conventional PCI endpoint
[    0.243035] pci 0000:00:14.2: BAR 0 [mem 0xa4418000-0xa4419fff 64bit]
[    0.243052] pci 0000:00:14.2: BAR 2 [mem 0xa441e000-0xa441efff 64bit]
[    0.243289] pci 0000:00:14.3: [8086:a370] type 00 class 0x028000 PCIe Root Complex Integrated Endpoint
[    0.243416] pci 0000:00:14.3: BAR 0 [mem 0xa4410000-0xa4413fff 64bit]
[    0.244128] pci 0000:00:14.3: PME# supported from D0 D3hot D3cold
[    0.245047] pci 0000:00:15.0: [8086:a368] type 00 class 0x0c8000 conventional PCI endpoint
[    0.246585] pci 0000:00:15.0: BAR 0 [mem 0x00000000-0x00000fff 64bit]
[    0.249265] pci 0000:00:15.1: [8086:a369] type 00 class 0x0c8000 conventional PCI endpoint
[    0.249815] pci 0000:00:15.1: BAR 0 [mem 0x00000000-0x00000fff 64bit]
[    0.252272] pci 0000:00:16.0: [8086:a360] type 00 class 0x078000 conventional PCI endpoint
[    0.252295] pci 0000:00:16.0: BAR 0 [mem 0xa4421000-0xa4421fff 64bit]
[    0.252384] pci 0000:00:16.0: PME# supported from D3hot
[    0.252865] pci 0000:00:17.0: [8086:a353] type 00 class 0x010601 conventional PCI endpoint
[    0.252885] pci 0000:00:17.0: BAR 0 [mem 0xa441a000-0xa441bfff]
[    0.252897] pci 0000:00:17.0: BAR 1 [mem 0xa4426000-0xa44260ff]
[    0.252908] pci 0000:00:17.0: BAR 2 [io  0x5080-0x5087]
[    0.252919] pci 0000:00:17.0: BAR 3 [io  0x5088-0x508b]
[    0.252930] pci 0000:00:17.0: BAR 4 [io  0x5060-0x507f]
[    0.252941] pci 0000:00:17.0: BAR 5 [mem 0xa4425000-0xa44257ff]
[    0.253003] pci 0000:00:17.0: PME# supported from D3hot
[    0.253414] pci 0000:00:1d.0: [8086:a330] type 01 class 0x060400 PCIe Root Port
[    0.253457] pci 0000:00:1d.0: PCI bridge to [bus 06]
[    0.253465] pci 0000:00:1d.0:   bridge window [mem 0xa4300000-0xa43fffff]
[    0.253582] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    0.253621] pci 0000:00:1d.0: PTM enabled (root), 4ns granularity
[    0.254299] pci 0000:00:1d.5: [8086:a335] type 01 class 0x060400 PCIe Root Port
[    0.254342] pci 0000:00:1d.5: PCI bridge to [bus 07]
[    0.254347] pci 0000:00:1d.5:   bridge window [io  0x3000-0x3fff]
[    0.254351] pci 0000:00:1d.5:   bridge window [mem 0xa4200000-0xa42fffff]
[    0.254465] pci 0000:00:1d.5: PME# supported from D0 D3hot D3cold
[    0.254497] pci 0000:00:1d.5: PTM enabled (root), 4ns granularity
[    0.255451] pci 0000:00:1e.0: [8086:a328] type 00 class 0x078000 conventional PCI endpoint
[    0.255920] pci 0000:00:1e.0: BAR 0 [mem 0x00000000-0x00000fff 64bit]
[    0.258319] pci 0000:00:1f.0: [8086:a30d] type 00 class 0x060100 conventional PCI endpoint
[    0.258817] pci 0000:00:1f.3: [8086:a348] type 00 class 0x040300 conventional PCI endpoint
[    0.258875] pci 0000:00:1f.3: BAR 0 [mem 0xa4414000-0xa4417fff 64bit]
[    0.258963] pci 0000:00:1f.3: BAR 4 [mem 0xa4100000-0xa41fffff 64bit]
[    0.259103] pci 0000:00:1f.3: PME# supported from D3hot D3cold
[    0.259795] pci 0000:00:1f.4: [8086:a323] type 00 class 0x0c0500 conventional PCI endpoint
[    0.259840] pci 0000:00:1f.4: BAR 0 [mem 0xa4423000-0xa44230ff 64bit]
[    0.259900] pci 0000:00:1f.4: BAR 4 [io  0x5040-0x505f]
[    0.260154] pci 0000:00:1f.5: [8086:a324] type 00 class 0x0c8000 conventional PCI endpoint
[    0.260173] pci 0000:00:1f.5: BAR 0 [mem 0xfe010000-0xfe010fff]
[    0.260314] pci 0000:01:00.0: [10de:1c8c] type 00 class 0x030000 PCIe Endpoint
[    0.260322] pci 0000:01:00.0: BAR 0 [mem 0xa3000000-0xa3ffffff]
[    0.260329] pci 0000:01:00.0: BAR 1 [mem 0x90000000-0x9fffffff 64bit pref]
[    0.260335] pci 0000:01:00.0: BAR 3 [mem 0xa0000000-0xa1ffffff 64bit pref]
[    0.260339] pci 0000:01:00.0: BAR 5 [io  0x4000-0x407f]
[    0.260343] pci 0000:01:00.0: ROM [mem 0xfff80000-0xffffffff pref]
[    0.260357] pci 0000:01:00.0: Enabling HDA controller
[    0.260622] pci 0000:01:00.1: [10de:0fb9] type 00 class 0x040300 PCIe Endpoint
[    0.260630] pci 0000:01:00.1: BAR 0 [mem 0xa4000000-0xa4003fff]
[    0.260722] pci 0000:00:01.0: PCI bridge to [bus 01-05]
[    0.261026] pci 0000:06:00.0: [8086:f1a5] type 00 class 0x010802 PCIe Endpoint
[    0.261053] pci 0000:06:00.0: BAR 0 [mem 0xa4300000-0xa4303fff 64bit]
[    0.261507] pci 0000:00:1d.0: PCI bridge to [bus 06]
[    0.261598] pci 0000:07:00.0: [10ec:5287] type 00 class 0xff0000 PCIe Endpoint
[    0.261619] pci 0000:07:00.0: BAR 0 [mem 0xa4205000-0xa4205fff]
[    0.261681] pci 0000:07:00.0: ROM [mem 0xffff0000-0xffffffff pref]
[    0.261807] pci 0000:07:00.0: supports D1 D2
[    0.261808] pci 0000:07:00.0: PME# supported from D1 D2 D3hot D3cold
[    0.262073] pci 0000:07:00.1: [10ec:8168] type 00 class 0x020000 PCIe Endpoint
[    0.262093] pci 0000:07:00.1: BAR 0 [io  0x3000-0x30ff]
[    0.262121] pci 0000:07:00.1: BAR 2 [mem 0xa4204000-0xa4204fff 64bit]
[    0.262138] pci 0000:07:00.1: BAR 4 [mem 0xa4200000-0xa4203fff 64bit]
[    0.262267] pci 0000:07:00.1: supports D1 D2
[    0.262268] pci 0000:07:00.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.262492] pci 0000:00:1d.5: PCI bridge to [bus 07]
[    0.267636] ACPI: EC: interrupt unblocked
[    0.267638] ACPI: EC: event unblocked
[    0.267649] ACPI: EC: EC_CMD/EC_SC=0x66, EC_DATA=0x62
[    0.267650] ACPI: EC: GPE=0x14
[    0.267651] ACPI: \_SB_.PCI0.LPCB.EC0_: Boot DSDT EC initialization complete
[    0.267653] ACPI: \_SB_.PCI0.LPCB.EC0_: EC: Used to handle transactions and events
[    0.267704] iommu: Default domain type: Translated
[    0.267704] iommu: DMA domain TLB invalidation policy: lazy mode
[    0.267704] SCSI subsystem initialized
[    0.267704] libata version 3.00 loaded.
[    0.267704] ACPI: bus type USB registered
[    0.267704] usbcore: registered new interface driver usbfs
[    0.267704] usbcore: registered new interface driver hub
[    0.267704] usbcore: registered new device driver usb
[    0.267704] EDAC MC: Ver: 3.0.0
[    0.268593] efivars: Registered efivars operations
[    0.268593] NetLabel: Initializing
[    0.268593] NetLabel:  domain hash size = 128
[    0.268593] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.268593] NetLabel:  unlabeled traffic allowed by default
[    0.268593] mctp: management component transport protocol core
[    0.268593] NET: Registered PF_MCTP protocol family
[    0.268593] PCI: Using ACPI for IRQ routing
[    0.351107] PCI: pci_cache_line_size set to 64 bytes
[    0.351569] e820: reserve RAM buffer [mem 0x0009f000-0x0009ffff]
[    0.351571] e820: reserve RAM buffer [mem 0x6e424018-0x6fffffff]
[    0.351572] e820: reserve RAM buffer [mem 0x6e435018-0x6fffffff]
[    0.351573] e820: reserve RAM buffer [mem 0x71897000-0x73ffffff]
[    0.351574] e820: reserve RAM buffer [mem 0x78b81000-0x7bffffff]
[    0.351575] e820: reserve RAM buffer [mem 0x88bae000-0x8bffffff]
[    0.351576] e820: reserve RAM buffer [mem 0x89d0f000-0x8bffffff]
[    0.351576] e820: reserve RAM buffer [mem 0x46e800000-0x46fffffff]
[    0.351604] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[    0.351604] pci 0000:00:02.0: vgaarb: bridge control possible
[    0.351604] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[    0.351604] pci 0000:01:00.0: vgaarb: bridge control possible
[    0.351604] pci 0000:01:00.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none
[    0.351604] vgaarb: loaded
[    0.351604] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[    0.351604] hpet0: 8 comparators, 64-bit 24.000000 MHz counter
[    0.354358] clocksource: Switched to clocksource tsc-early
[    0.354904] VFS: Disk quotas dquot_6.6.0
[    0.354913] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.354983] pnp: PnP ACPI init
[    0.355256] system 00:00: [io  0x1800-0x18fe] has been reserved
[    0.355259] system 00:00: [mem 0xfd000000-0xfd69ffff] has been reserved
[    0.355261] system 00:00: [mem 0xfd6c0000-0xfd6cffff] has been reserved
[    0.355262] system 00:00: [mem 0xfd6f0000-0xfdffffff] has been reserved
[    0.355263] system 00:00: [mem 0xfe000000-0xfe01ffff] could not be reserved
[    0.355265] system 00:00: [mem 0xfe200000-0xfe7fffff] has been reserved
[    0.355266] system 00:00: [mem 0xfc7e0000-0xfc7e0fff] has been reserved
[    0.355491] system 00:01: [io  0x2000-0x20fe] has been reserved
[    0.355579] system 00:02: [io  0x0680-0x069f] has been reserved
[    0.355581] system 00:02: [io  0x164e-0x164f] has been reserved
[    0.355582] system 00:02: [io  0xfd60-0xfd63] has been reserved
[    0.355684] system 00:04: [io  0x1854-0x1857] has been reserved
[    0.357316] system 00:07: [mem 0xfed10000-0xfed17fff] has been reserved
[    0.357319] system 00:07: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.357320] system 00:07: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.357322] system 00:07: [mem 0xe0000000-0xefffffff] has been reserved
[    0.357323] system 00:07: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.357324] system 00:07: [mem 0xfed90000-0xfed93fff] could not be reserved
[    0.357325] system 00:07: [mem 0xfed45000-0xfed8ffff] could not be reserved
[    0.357327] system 00:07: [mem 0xfee00000-0xfeefffff] could not be reserved
[    0.357672] pnp: PnP ACPI: found 8 devices
[    0.363011] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.363056] NET: Registered PF_INET protocol family
[    0.363151] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.375333] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    0.375350] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.375378] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.375536] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear)
[    0.375707] TCP: Hash tables configured (established 131072 bind 65536)
[    0.375768] MPTCP token hash table entries: 16384 (order: 6, 393216 bytes, linear)
[    0.375804] UDP hash table entries: 8192 (order: 6, 262144 bytes, linear)
[    0.375832] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes, linear)
[    0.375872] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.375878] NET: Registered PF_XDP protocol family
[    0.375881] pci 0000:01:00.0: ROM [mem 0xfff80000-0xffffffff pref]: can't claim; no compatible bridge window
[    0.375884] pci 0000:07:00.0: ROM [mem 0xffff0000-0xffffffff pref]: can't claim; no compatible bridge window
[    0.375892] resource: avoiding allocation from e820 entry [mem 0x0009f000-0x000fffff]
[    0.375894] pci 0000:00:15.0: BAR 0 [mem 0x8f800000-0x8f800fff 64bit]: assigned
[    0.376126] resource: avoiding allocation from e820 entry [mem 0x0009f000-0x000fffff]
[    0.376128] pci 0000:00:15.1: BAR 0 [mem 0x8f801000-0x8f801fff 64bit]: assigned
[    0.376397] resource: avoiding allocation from e820 entry [mem 0x0009f000-0x000fffff]
[    0.376399] pci 0000:00:1e.0: BAR 0 [mem 0x8f802000-0x8f802fff 64bit]: assigned
[    0.376669] pci 0000:01:00.0: ROM [mem 0xa4080000-0xa40fffff pref]: assigned
[    0.376671] pci 0000:00:01.0: PCI bridge to [bus 01-05]
[    0.376673] pci 0000:00:01.0:   bridge window [io  0x4000-0x4fff]
[    0.376675] pci 0000:00:01.0:   bridge window [mem 0xa3000000-0xa40fffff]
[    0.376677] pci 0000:00:01.0:   bridge window [mem 0x90000000-0xa1ffffff 64bit pref]
[    0.376680] pci 0000:00:1d.0: PCI bridge to [bus 06]
[    0.376689] pci 0000:00:1d.0:   bridge window [mem 0xa4300000-0xa43fffff]
[    0.376700] pci 0000:07:00.0: ROM [mem 0xa4210000-0xa421ffff pref]: assigned
[    0.376701] pci 0000:00:1d.5: PCI bridge to [bus 07]
[    0.376703] pci 0000:00:1d.5:   bridge window [io  0x3000-0x3fff]
[    0.376709] pci 0000:00:1d.5:   bridge window [mem 0xa4200000-0xa42fffff]
[    0.376719] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.376720] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.376722] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.376723] pci_bus 0000:00: resource 7 [mem 0x8f800000-0xdfffffff window]
[    0.376724] pci_bus 0000:00: resource 8 [mem 0xfc800000-0xfe7fffff window]
[    0.376725] pci_bus 0000:01: resource 0 [io  0x4000-0x4fff]
[    0.376726] pci_bus 0000:01: resource 1 [mem 0xa3000000-0xa40fffff]
[    0.376727] pci_bus 0000:01: resource 2 [mem 0x90000000-0xa1ffffff 64bit pref]
[    0.376728] pci_bus 0000:06: resource 1 [mem 0xa4300000-0xa43fffff]
[    0.376729] pci_bus 0000:07: resource 0 [io  0x3000-0x3fff]
[    0.376730] pci_bus 0000:07: resource 1 [mem 0xa4200000-0xa42fffff]
[    0.378712] pci 0000:01:00.1: extending delay after power-on from D3hot to 20 msec
[    0.378735] pci 0000:01:00.1: D0 power state depends on 0000:01:00.0
[    0.378810] PCI: CLS 64 bytes, default 64
[    0.378874] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.378875] software IO TLB: mapped [mem 0x0000000080c20000-0x0000000084c20000] (64MB)
[    0.378899] Trying to unpack rootfs image as initramfs...
[    0.384981] Initialise system trusted keyrings
[    0.384990] Key type blacklist registered
[    0.385023] workingset: timestamp_bits=41 max_order=22 bucket_order=0
[    0.385029] zbud: loaded
[    0.385106] fuse: init (API version 7.40)
[    0.385167] integrity: Platform Keyring initialized
[    0.385169] integrity: Machine keyring initialized
[    0.394541] Key type asymmetric registered
[    0.394543] Asymmetric key parser 'x509' registered
[    0.394564] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[    0.394600] io scheduler mq-deadline registered
[    0.394601] io scheduler kyber registered
[    0.394609] io scheduler bfq registered
[    0.394918] pcieport 0000:00:01.0: PME: Signaling with IRQ 120
[    0.395130] pcieport 0000:00:1d.0: PME: Signaling with IRQ 121
[    0.395178] pcieport 0000:00:1d.0: AER: enabled with IRQ 121
[    0.395207] pcieport 0000:00:1d.0: DPC: enabled with IRQ 121
[    0.395208] pcieport 0000:00:1d.0: DPC: error containment capabilities: Int Msg #0, RPExt+ PoisonedTLP+ SwTrigger+ RP PIO Log 4, DL_ActiveErr+
[    0.395442] pcieport 0000:00:1d.5: PME: Signaling with IRQ 122
[    0.395485] pcieport 0000:00:1d.5: AER: enabled with IRQ 122
[    0.395518] pcieport 0000:00:1d.5: DPC: enabled with IRQ 122
[    0.395519] pcieport 0000:00:1d.5: DPC: error containment capabilities: Int Msg #0, RPExt+ PoisonedTLP+ SwTrigger+ RP PIO Log 4, DL_ActiveErr+
[    0.395618] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    0.396147] ACPI: AC: AC Adapter [ACAD] (on-line)
[    0.396185] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:18/PNP0C0D:00/input/input0
[    0.396198] ACPI: button: Lid Switch [LID0]
[    0.396226] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
[    0.396238] ACPI: button: Sleep Button [SLPB]
[    0.396257] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[    0.396436] ACPI: button: Power Button [PWRB]
[    0.396463] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    0.396527] ACPI: button: Power Button [PWRF]
[    0.398065] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    0.398838] ACPI: battery: Slot [BAT1] (battery present)
[    0.399666] Non-volatile memory driver v1.3
[    0.399667] Linux agpgart interface v0.103
[    0.467596] ahci 0000:00:17.0: version 3.0
[    0.475943] Initramfs unpacking failed: invalid magic at start of compressed archive
[    0.477965] ahci 0000:00:17.0: AHCI vers 0001.0301, 32 command slots, 6 Gbps, SATA mode
[    0.477970] ahci 0000:00:17.0: 1/1 ports implemented (port mask 0x10)
[    0.477972] ahci 0000:00:17.0: flags: 64bit ncq sntf pm clo only pio slum part ems deso sadm sds apst 
[    0.478507] scsi host0: ahci
[    0.478760] scsi host1: ahci
[    0.479007] scsi host2: ahci
[    0.479113] scsi host3: ahci
[    0.479211] scsi host4: ahci
[    0.479235] ata1: DUMMY
[    0.479236] ata2: DUMMY
[    0.479236] ata3: DUMMY
[    0.479237] ata4: DUMMY
[    0.479242] ata5: SATA max UDMA/133 abar m2048@0xa4425000 port 0xa4425300 irq 123 lpm-pol 3
[    0.479320] ACPI: bus type drm_connector registered
[    0.479850] usbcore: registered new interface driver usbserial_generic
[    0.479855] usbserial: USB Serial support registered for generic
[    0.479949] rtc_cmos 00:03: RTC can wake from S4
[    0.481577] rtc_cmos 00:03: registered as rtc0
[    0.481928] rtc_cmos 00:03: setting system clock to 2024-08-28T03:27:24 UTC (1724815644)
[    0.481962] rtc_cmos 00:03: alarms up to one month, y3k, 242 bytes nvram
[    0.482230] intel_pstate: Intel P-state driver initializing
[    0.482722] intel_pstate: Disabling energy efficiency optimization
[    0.482723] intel_pstate: HWP enabled
[    0.482762] ledtrig-cpu: registered to indicate activity on CPUs
[    0.483010] [drm] Initialized simpledrm 1.0.0 20200625 for simple-framebuffer.0 on minor 0
[    0.486598] Console: switching to colour frame buffer device 240x67
[    0.490262] simple-framebuffer simple-framebuffer.0: [drm] fb0: simpledrmdrmfb frame buffer device
[    0.490461] hid: raw HID events driver (C) Jiri Kosina
[    0.490622] drop_monitor: Initializing network drop monitor service
[    0.490744] NET: Registered PF_INET6 protocol family
[    0.507411] Freeing initrd memory: 465196K
[    0.512427] Segment Routing with IPv6
[    0.512429] RPL Segment Routing with IPv6
[    0.512443] In-situ OAM (IOAM) with IPv6
[    0.512474] NET: Registered PF_PACKET protocol family
[    0.515684] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[    0.515934] microcode: Current revision: 0x000000f8
[    0.515935] microcode: Updated early from: 0x000000b4
[    0.516121] IPI shorthand broadcast: enabled
[    0.517552] sched_clock: Marking stable (507001566, 9637316)->(524461995, -7823113)
[    0.517706] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level
[    0.517917] registered taskstats version 1
[    0.518484] Loading compiled-in X.509 certificates
[    0.520448] Loaded X.509 cert 'Build time autogenerated kernel key: af321b7fc7cd478513d84c2e5cd0f9e2e8a97af4'
[    0.521709] Demotion targets for Node 0: null
[    0.521893] Key type .fscrypt registered
[    0.521894] Key type fscrypt-provisioning registered
[    0.524896] integrity: Loading X.509 certificate: UEFI:db
[    0.524925] integrity: Loaded X.509 cert 'Microsoft Windows Production PCA 2011: a92902398e16c49778cd90f99e4f9ae17c55af53'
[    0.524927] integrity: Loading X.509 certificate: UEFI:db
[    0.524940] integrity: Loaded X.509 cert 'Microsoft Corporation UEFI CA 2011: 13adbf4309bd82709c8cd54f316ed522988a1bd4'
[    0.524940] integrity: Loading X.509 certificate: UEFI:db
[    0.524949] integrity: Loaded X.509 cert 'Acer Database: 84f00f5841571abd2cc11a8c26d5c9c8d2b6b0b5'
[    0.524949] integrity: Loading X.509 certificate: UEFI:db
[    0.524951] integrity: Problem loading X.509 certificate -65
[    0.524962] integrity: Error adding keys to platform keyring UEFI:db
[    0.524963] integrity: Loading X.509 certificate: UEFI:db
[    0.524965] integrity: Problem loading X.509 certificate -65
[    0.524971] integrity: Error adding keys to platform keyring UEFI:db
[    0.524971] integrity: Loading X.509 certificate: UEFI:db
[    0.527778] integrity: Loaded X.509 cert 'Linpus: linpus.com: 2e092cab5e97a89f94a6e272ec7267c267cf4483'
[    0.535893] PM:   Magic number: 4:359:463
[    0.538603] RAS: Correctable Errors collector initialized.
[    0.548615] clk: Disabling unused clocks
[    0.548617] PM: genpd: Disabling unused power domains
[    0.791332] ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    0.792235] ata5.00: supports DRM functions and may not be fully accessible
[    0.792242] ata5.00: ATA-10: CT500MX500SSD1, M3CR023, max UDMA/133
[    0.792366] ata5.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 32), AA
[    0.793685] ata5.00: Features: Trust Dev-Sleep
[    0.794008] ata5.00: supports DRM functions and may not be fully accessible
[    0.795228] ata5.00: configured for UDMA/133
[    0.805399] ahci 0000:00:17.0: port does not support device sleep
[    0.805811] scsi 4:0:0:0: Direct-Access     ATA      CT500MX500SSD1   023  PQ: 0 ANSI: 5
[    0.806896] sd 4:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[    0.806903] sd 4:0:0:0: [sda] 4096-byte physical blocks
[    0.806960] sd 4:0:0:0: [sda] Write Protect is off
[    0.806967] sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    0.807099] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    0.807468] sd 4:0:0:0: [sda] Preferred minimum I/O size 4096 bytes
[    0.810120]  sda: sda1
[    0.810481] sd 4:0:0:0: [sda] supports TCG Opal
[    0.810488] sd 4:0:0:0: [sda] Attached SCSI disk
[    0.812753] Freeing unused decrypted memory: 2028K
[    0.813595] Freeing unused kernel image (initmem) memory: 3564K
[    0.813737] Write protecting the kernel read-only data: 34816k
[    0.814785] Freeing unused kernel image (rodata/data gap) memory: 1052K
[    0.880825] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    0.880827] rodata_test: all tests were successful
[    0.880828] x86/mm: Checking user space page tables
[    0.916219] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    0.916223] Run /init as init process
[    0.916224]   with arguments:
[    0.916225]     /init
[    0.916226]   with environment:
[    0.916226]     HOME=/
[    0.916227]     TERM=linux
[    1.035058] wmi_bus wmi_bus-PNP0C14:00: [Firmware Bug]: WMBF method block execution control method not found
[    1.035345] wmi_bus wmi_bus-PNP0C14:01: [Firmware Info]: 00000000-0000-0000-0000-000000000000 has zero instances
[    1.035347] wmi_bus wmi_bus-PNP0C14:01: [Firmware Info]: 00000000-0000-0000-0000-000000000000 has zero instances
[    1.035348] wmi_bus wmi_bus-PNP0C14:01: [Firmware Info]: 00000000-0000-0000-0000-000000000000 has zero instances
[    1.035348] wmi_bus wmi_bus-PNP0C14:01: [Firmware Info]: 00000000-0000-0000-0000-000000000000 has zero instances
[    1.400667] tsc: Refined TSC clocksource calibration: 2304.000 MHz
[    1.400672] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2135f7c97c8, max_idle_ns: 440795273205 ns
[    1.400748] clocksource: Switched to clocksource tsc
[    1.456907] Setting dangerous option enable_psr - tainting kernel
[    1.461989] Console: switching to colour dummy device 80x25
[    1.480309] i915 0000:00:02.0: vgaarb: deactivate vga console
[    1.482563] i915 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=none:owns=io+mem
[    1.483507] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4)
[    2.659541] [drm] Initialized i915 1.6.0 20230929 for 0000:00:02.0 on minor 1
[    2.661354] ACPI: video: [Firmware Bug]: ACPI(PEGP) defines _DOD but not _DOS
[    2.661399] ACPI: video: Video Device [PEGP] (multi-head: yes  rom: yes  post: no)
[    2.661502] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:00/LNXVIDEO:00/input/input4
[    2.666869] ACPI: video: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[    2.667058] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:01/input/input5
[    2.668618] fbcon: i915drmfb (fb0) is primary device
[    2.673554] Console: switching to colour frame buffer device 240x67
[    2.691419] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device
[    3.102056] nvidia: loading out-of-tree module taints kernel.
[    3.102063] nvidia: module license 'NVIDIA' taints kernel.
[    3.102064] Disabling lock debugging due to kernel taint
[    3.102066] nvidia: module verification failed: signature and/or required key missing - tainting kernel
[    3.102067] nvidia: module license taints kernel.
[    3.524431] nvidia-nvlink: Nvlink Core is being initialized, major device number 238

[    3.525553] nvidia 0000:01:00.0: enabling device (0106 -> 0107)
[    3.525705] nvidia 0000:01:00.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=none:owns=none
[    3.727852] NVRM: loading NVIDIA UNIX x86_64 Kernel Module  560.35.03  Fri Aug 16 21:39:15 UTC 2024
[    3.790714] nvidia-modeset: Loading NVIDIA Kernel Mode Setting Driver for UNIX platforms  560.35.03  Fri Aug 16 21:21:48 UTC 2024
[    3.818970] nvidia_uvm: module uses symbols nvUvmInterfaceDisableAccessCntr from proprietary module nvidia, inheriting taint.
[    3.964955] nvidia-uvm: Loaded the UVM driver, major device number 236.
[    3.968217] [drm] [nvidia-drm] [GPU ID 0x00000100] Loading driver
[    3.992729] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20240322/nsarguments-61)
[    4.720324] [drm] Initialized nvidia-drm 0.0.0 20160202 for 0000:01:00.0 on minor 0
[    4.725324] usbcore: registered new interface driver usbhid
[    4.725326] usbhid: USB HID core driver
[    4.740818] nvme nvme0: pci function 0000:06:00.0
[    4.751601] nvme nvme0: 8/0/0 default/read/poll queues
[    4.758352]  nvme0n1: p1 p2 p3 p4 p5
[    4.761946] raid6: skipped pq benchmark and selected avx2x4
[    4.761948] raid6: using avx2x2 recovery algorithm
[    4.764493] xor: automatically using best checksumming function   avx       
[    4.876268] Btrfs loaded, zoned=yes, fsverity=yes
[    4.880745] usbcore: registered new interface driver usb-storage
[    4.883531] usbcore: registered new interface driver uas
[    5.015828] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[    5.015833] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[    5.016548] serio: i8042 KBD port at 0x60,0x64 irq 1
[    5.022332] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    5.022340] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[    5.023426] xhci_hcd 0000:00:14.0: hcc params 0x20007fc1 hci version 0x110 quirks 0x0000000000009810
[    5.023780] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    5.023785] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[    5.023801] xhci_hcd 0000:00:14.0: Host supports USB 3.1 Enhanced SuperSpeed
[    5.023864] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10
[    5.023867] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    5.023869] usb usb1: Product: xHCI Host Controller
[    5.023870] usb usb1: Manufacturer: Linux 6.10.6-zen1-1-zen xhci-hcd
[    5.023871] usb usb1: SerialNumber: 0000:00:14.0
[    5.024056] hub 1-0:1.0: USB hub found
[    5.024095] hub 1-0:1.0: 16 ports detected
[    5.025252] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.10
[    5.025256] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    5.025258] usb usb2: Product: xHCI Host Controller
[    5.025260] usb usb2: Manufacturer: Linux 6.10.6-zen1-1-zen xhci-hcd
[    5.025262] usb usb2: SerialNumber: 0000:00:14.0
[    5.025463] hub 2-0:1.0: USB hub found
[    5.025626] hub 2-0:1.0: 8 ports detected
[    5.025797] usb: port power management may be unreliable
[    5.062206] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input6
[    5.266798] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[    5.393272] usb 1-1: New USB device found, idVendor=045b, idProduct=0209, bcdDevice= 1.00
[    5.393287] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    5.394428] hub 1-1:1.0: USB hub found
[    5.394477] hub 1-1:1.0: 4 ports detected
[    5.507159] usb 2-1: new SuperSpeed USB device number 2 using xhci_hcd
[    5.523682] usb 2-1: New USB device found, idVendor=045b, idProduct=0210, bcdDevice= 1.00
[    5.523697] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    5.525720] hub 2-1:1.0: USB hub found
[    5.526147] hub 2-1:1.0: 4 ports detected
[    5.635752] usb 1-3: new full-speed USB device number 3 using xhci_hcd
[    5.763578] usb 1-3: New USB device found, idVendor=1532, idProduct=008c, bcdDevice= 2.00
[    5.763595] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    5.763602] usb 1-3: Product: Razer DeathAdder V2 Mini
[    5.763608] usb 1-3: Manufacturer: Razer
[    5.779545] input: Razer Razer DeathAdder V2 Mini as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.0/0003:1532:008C.0001/input/input7
[    5.779625] hid-generic 0003:1532:008C.0001: input,hidraw0: USB HID v1.11 Mouse [Razer Razer DeathAdder V2 Mini] on usb-0000:00:14.0-3/input0
[    5.779831] input: Razer Razer DeathAdder V2 Mini Keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.1/0003:1532:008C.0002/input/input8
[    5.832066] input: Razer Razer DeathAdder V2 Mini as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.1/0003:1532:008C.0002/input/input9
[    5.832337] hid-generic 0003:1532:008C.0002: input,hidraw1: USB HID v1.11 Keyboard [Razer Razer DeathAdder V2 Mini] on usb-0000:00:14.0-3/input1
[    5.832708] input: Razer Razer DeathAdder V2 Mini as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.2/0003:1532:008C.0003/input/input10
[    5.838816] usb 1-1.1: new high-speed USB device number 4 using xhci_hcd
[    5.885369] hid-generic 0003:1532:008C.0003: input,hidraw2: USB HID v1.11 Keyboard [Razer Razer DeathAdder V2 Mini] on usb-0000:00:14.0-3/input2
[    5.927126] usb 1-1.1: New USB device found, idVendor=045b, idProduct=0209, bcdDevice= 1.00
[    5.927140] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    5.928353] hub 1-1.1:1.0: USB hub found
[    5.928398] hub 1-1.1:1.0: 4 ports detected
[    5.995159] usb 2-1.1: new SuperSpeed USB device number 3 using xhci_hcd
[    6.010217] usb 2-1.1: New USB device found, idVendor=045b, idProduct=0210, bcdDevice= 1.00
[    6.010224] usb 2-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    6.012364] hub 2-1.1:1.0: USB hub found
[    6.012760] hub 2-1.1:1.0: 4 ports detected
[    6.122749] usb 1-4: new high-speed USB device number 5 using xhci_hcd
[    6.251749] usb 1-4: New USB device found, idVendor=174c, idProduct=55aa, bcdDevice= 1.00
[    6.251765] usb 1-4: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[    6.251772] usb 1-4: Product: ED600
[    6.251777] usb 1-4: Manufacturer: ADATA
[    6.251782] usb 1-4: SerialNumber: 0000000000C0
[    6.258822] scsi host5: uas
[    6.260156] scsi 5:0:0:0: Direct-Access     ADATA    ED600            0    PQ: 0 ANSI: 6
[    6.267290] sd 5:0:0:0: [sdb] 937703088 512-byte logical blocks: (480 GB/447 GiB)
[    6.267628] sd 5:0:0:0: [sdb] Write Protect is off
[    6.267649] sd 5:0:0:0: [sdb] Mode Sense: 43 00 00 00
[    6.268208] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.268424] sd 5:0:0:0: [sdb] Preferred minimum I/O size 512 bytes
[    6.268430] sd 5:0:0:0: [sdb] Optimal transfer size 33553920 bytes
[    6.276884]  sdb: sdb1 sdb2 sdb3 sdb5
[    6.277604] sd 5:0:0:0: [sdb] Attached SCSI disk
[    6.327721] usb 1-1.2: new full-speed USB device number 6 using xhci_hcd
[    6.425071] usb 1-1.2: New USB device found, idVendor=17a0, idProduct=0305, bcdDevice= 2.07
[    6.425086] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    6.425092] usb 1-1.2: Product: Samson GoMic
[    6.425125] usb 1-1.2: Manufacturer: Samson Technologies
[    6.430306] input: Samson Technologies Samson GoMic as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.2/1-1.2:1.3/0003:17A0:0305.0004/input/input11
[    6.482113] hid-generic 0003:17A0:0305.0004: input,hidraw3: USB HID v1.00 Device [Samson Technologies Samson GoMic] on usb-0000:00:14.0-1.2/input3
[    6.494720] usb 1-1.1.2: new high-speed USB device number 7 using xhci_hcd
[    6.584140] usb 1-1.1.2: language id specifier not provided by device, defaulting to English
[    6.584495] usb 1-1.1.2: New USB device found, idVendor=17cc, idProduct=1978, bcdDevice= 0.0e
[    6.584505] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[    6.584511] usb 1-1.1.2: Product: Audio 8 DJ
[    6.584516] usb 1-1.1.2: Manufacturer: Native Instruments
[    6.584521] usb 1-1.1.2: SerialNumber: SN-H3KG25C3X4   
[    6.649885] usb 2-1.1.4: new SuperSpeed USB device number 4 using xhci_hcd
[    6.662816] usb 2-1.1.4: New USB device found, idVendor=17e9, idProduct=4301, bcdDevice=36.05
[    6.662829] usb 2-1.1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    6.662836] usb 2-1.1.4: Product: USB3 to HDMI
[    6.662841] usb 2-1.1.4: Manufacturer: DisplayLink
[    6.662845] usb 2-1.1.4: SerialNumber: U3HD338626295
[    6.731520] BTRFS: device label sfroot devid 1 transid 461475 /dev/sdb1 (8:17) scanned by mount (290)
[    6.732619] BTRFS info (device sdb1): first mount of filesystem 91ae5638-1608-41e0-bf5f-c3c1aecb7801
[    6.732672] BTRFS info (device sdb1): using crc32c (crc32c-intel) checksum algorithm
[    6.732684] BTRFS info (device sdb1): using free-space-tree
[    6.775723] usb 1-5: new high-speed USB device number 8 using xhci_hcd
[    6.911616] usb 1-5: New USB device found, idVendor=04f2, idProduct=b5f7, bcdDevice=92.26
[    6.911630] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    6.911636] usb 1-5: Product: HD WebCam
[    6.911655] usb 1-5: Manufacturer: Chicony Electronics Co.,Ltd.
[    6.980694] usb 1-1.3: new high-speed USB device number 9 using xhci_hcd
[    7.069163] usb 1-1.3: New USB device found, idVendor=1a40, idProduct=0101, bcdDevice= 1.11
[    7.069178] usb 1-1.3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    7.069185] usb 1-1.3: Product: USB 2.0 Hub
[    7.070429] hub 1-1.3:1.0: USB hub found
[    7.070472] hub 1-1.3:1.0: 4 ports detected
[    7.144689] usb 1-1.1.3: new full-speed USB device number 10 using xhci_hcd
[    7.235417] usb 1-1.1.3: New USB device found, idVendor=2011, idProduct=0715, bcdDevice= 0.00
[    7.235432] usb 1-1.1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    7.235439] usb 1-1.1.3: Product: MPKmini2
[    7.235444] usb 1-1.1.3: Manufacturer: AKAI
[    7.235448] usb 1-1.1.3: SerialNumber: 0001
[    7.249106] hid-generic 0003:2011:0715.0005: hiddev96,hidraw4: USB HID v1.11 Device [AKAI MPKmini2] on usb-0000:00:14.0-1.1.3/input0
[    7.347753] usb 1-14: new full-speed USB device number 11 using xhci_hcd
[    7.476666] usb 1-14: New USB device found, idVendor=8087, idProduct=0aaa, bcdDevice= 0.02
[    7.476681] usb 1-14: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    7.656767] usb 1-1.3.4: new full-speed USB device number 12 using xhci_hcd
[    7.847064] usb 1-1.3.4: New USB device found, idVendor=28bd, idProduct=092b, bcdDevice= 0.00
[    7.847079] usb 1-1.3.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    7.847086] usb 1-1.3.4: Product: 13.3 inch PenDisplay
[    7.847091] usb 1-1.3.4: Manufacturer: UGTABLET
[    7.847096] usb 1-1.3.4: SerialNumber: 000000
[    7.861697] input: UGTABLET 13.3 inch PenDisplay Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.3/1-1.3.4/1-1.3.4:1.0/0003:28BD:092B.0006/input/input12
[    7.861986] input: UGTABLET 13.3 inch PenDisplay Keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.3/1-1.3.4/1-1.3.4:1.0/0003:28BD:092B.0006/input/input13
[    7.914116] hid-generic 0003:28BD:092B.0006: input,hidraw5: USB HID v1.00 Mouse [UGTABLET 13.3 inch PenDisplay] on usb-0000:00:14.0-1.3.4/input0
[    7.916309] input: UGTABLET 13.3 inch PenDisplay as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.3/1-1.3.4/1-1.3.4:1.1/0003:28BD:092B.0007/input/input14
[    7.916691] hid-generic 0003:28BD:092B.0007: input,hidraw6: USB HID v1.00 Device [UGTABLET 13.3 inch PenDisplay] on usb-0000:00:14.0-1.3.4/input1
[    7.918348] hid-generic 0003:28BD:092B.0008: hiddev97,hidraw7: USB HID v1.00 Device [UGTABLET 13.3 inch PenDisplay] on usb-0000:00:14.0-1.3.4/input2
[    8.019984] systemd[1]: systemd 256.5-1-arch running in system mode (+PAM +AUDIT -SELINUX -APPARMOR -IMA +SMACK +SECCOMP +GCRYPT +GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBCRYPTSETUP_PLUGINS +LIBFDISK +PCRE2 +PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD +BPF_FRAMEWORK +XKBCOMMON +UTMP -SYSVINIT +LIBARCHIVE)
[    8.020005] systemd[1]: Detected architecture x86-64.
[    8.023314] systemd[1]: Hostname set to <fungi-puter>.
[    8.156430] systemd[1]: bpf-restrict-fs: LSM BPF program attached
[   10.219825] zram_generator::config[338]: zram0: unknown key compression-algorith, ignoring.
[   10.281090] zram: Added device: zram0
[   10.384348] (sd-exec-[320]: /usr/lib/systemd/system-generators/systemd-fstab-generator failed with exit status 1.
[   10.746395] systemd[1]: Configuration file /etc/systemd/system/windscribe-helper.service is marked executable. Please remove executable permission bits. Proceeding anyway.
[   10.757305] systemd[1]: Queued start job for default target Graphical Interface.
[   10.777511] systemd[1]: Created slice Virtual Machine and Container Slice.
[   10.778248] systemd[1]: Created slice Slice /system/dirmngr.
[   10.778547] systemd[1]: Created slice Slice /system/getty.
[   10.778855] systemd[1]: Created slice Slice /system/gpg-agent.
[   10.779157] systemd[1]: Created slice Slice /system/gpg-agent-browser.
[   10.779455] systemd[1]: Created slice Slice /system/gpg-agent-extra.
[   10.779777] systemd[1]: Created slice Slice /system/gpg-agent-ssh.
[   10.780082] systemd[1]: Created slice Slice /system/keyboxd.
[   10.780385] systemd[1]: Created slice Slice /system/modprobe.
[   10.780691] systemd[1]: Created slice Slice /system/systemd-fsck.
[   10.780992] systemd[1]: Created slice Slice /system/systemd-zram-setup.
[   10.781199] systemd[1]: Created slice User and Session Slice.
[   10.781281] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[   10.781437] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[   10.781484] systemd[1]: Expecting device /dev/disk/by-label/crucial...
[   10.781512] systemd[1]: Expecting device /dev/disk/by-uuid/9725d41a-8f03-49c0-800b-e89e64291fe8...
[   10.781544] systemd[1]: Expecting device /dev/disk/by-uuid/E25D-EC2D...
[   10.781571] systemd[1]: Expecting device /dev/disk/by-uuid/b169df77-c9f8-4985-bbbc-1f7a4b9ee02f...
[   10.781601] systemd[1]: Expecting device /dev/zram0...
[   10.781631] systemd[1]: Reached target Login Prompts.
[   10.781705] systemd[1]: Reached target Local Integrity Protected Volumes.
[   10.781774] systemd[1]: Reached target Remote File Systems.
[   10.781827] systemd[1]: Reached target Slice Units.
[   10.781890] systemd[1]: Reached target Local Verity Protected Volumes.
[   10.782000] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[   10.782120] systemd[1]: Listening on LVM2 poll daemon socket.
[   10.785987] systemd[1]: Listening on Process Core Dump Socket.
[   10.786577] systemd[1]: Listening on Credential Encryption/Decryption.
[   10.786726] systemd[1]: Listening on Journal Socket (/dev/log).
[   10.786857] systemd[1]: Listening on Journal Sockets.
[   10.786939] systemd[1]: TPM PCR Measurements was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
[   10.786950] systemd[1]: Make TPM PCR Policy was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
[   10.787014] systemd[1]: Listening on udev Control Socket.
[   10.787113] systemd[1]: Listening on udev Kernel Socket.
[   10.789929] systemd[1]: Mounting Huge Pages File System...
[   10.790577] systemd[1]: Mounting POSIX Message Queue File System...
[   10.791261] systemd[1]: Mounting Kernel Debug File System...
[   10.791934] systemd[1]: Mounting Kernel Trace File System...
[   10.792782] systemd[1]: Starting Create List of Static Device Nodes...
[   10.793484] systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling...
[   10.794267] systemd[1]: Starting Load Kernel Module configfs...
[   10.795784] systemd[1]: Starting Load Kernel Module dm_mod...
[   10.798743] systemd[1]: Starting Load Kernel Module drm...
[   10.799778] systemd[1]: Starting Load Kernel Module fuse...
[   10.800910] systemd[1]: Starting Load Kernel Module loop...
[   10.801119] systemd[1]: Clear Stale Hibernate Storage Info was skipped because of an unmet condition check (ConditionPathExists=/sys/firmware/efi/efivars/HibernateLocation-8cf2644b-4b0b-428f-9387-6d876050dc67).
[   10.802845] systemd[1]: Starting Journal Service...
[   10.868882] systemd[1]: Starting Load Kernel Modules...
[   10.869161] systemd[1]: TPM PCR Machine ID Measurement was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
[   10.871574] systemd[1]: Starting Remount Root and Kernel File Systems...
[   10.874836] systemd[1]: Early TPM SRK Setup was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
[   10.877192] systemd[1]: Starting Load udev Rules from Credentials...
[   10.893394] systemd[1]: Starting Coldplug All udev Devices...
[   10.900563] systemd[1]: Starting Virtual Console Setup...
[   10.913127] systemd[1]: Mounted Huge Pages File System.
[   10.915211] systemd[1]: Mounted POSIX Message Queue File System.
[   10.915528] device-mapper: uevent: version 1.0.3
[   10.915626] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev
[   10.916554] systemd[1]: Mounted Kernel Debug File System.
[   10.917210] systemd[1]: Mounted Kernel Trace File System.
[   10.918131] systemd[1]: Finished Create List of Static Device Nodes.
[   10.919715] systemd[1]: modprobe@configfs.service: Deactivated successfully.
[   10.919990] systemd[1]: Finished Load Kernel Module configfs.
[   10.920925] systemd[1]: modprobe@dm_mod.service: Deactivated successfully.
[   10.921147] systemd[1]: Finished Load Kernel Module dm_mod.
[   10.921942] systemd[1]: modprobe@drm.service: Deactivated successfully.
[   10.922137] systemd[1]: Finished Load Kernel Module drm.
[   10.923446] systemd[1]: modprobe@fuse.service: Deactivated successfully.
[   10.923628] systemd[1]: Finished Load Kernel Module fuse.
[   10.925780] systemd[1]: Mounting FUSE Control File System...
[   10.927458] systemd[1]: Mounting Kernel Configuration File System...
[   10.929152] systemd[1]: Starting Create Static Device Nodes in /dev gracefully...
[   10.934526] i2c_dev: i2c /dev entries driver
[   10.944395] tun: Universal TUN/TAP device driver, 1.6
[   10.949571] loop: module loaded
[   10.950157] systemd[1]: modprobe@loop.service: Deactivated successfully.
[   10.950360] systemd[1]: Finished Load Kernel Module loop.
[   10.951395] systemd[1]: Mounted Kernel Configuration File System.
[   10.952268] systemd[1]: Repartition Root Disk was skipped because no trigger condition checks were met.
[   10.984388] systemd[1]: Mounted FUSE Control File System.
[   11.088229] systemd[1]: Finished Create Static Device Nodes in /dev gracefully.
[   11.088824] systemd[1]: Finished Load udev Rules from Credentials.
[   11.125461] systemd[1]: Finished Load Kernel Modules.
[   11.126502] systemd[1]: Starting Apply Kernel Variables...
[   11.135414] systemd-journald[359]: Collecting audit messages is disabled.
[   11.142818] systemd[1]: Finished Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling.
[   11.174033] systemd[1]: Finished Remount Root and Kernel File Systems.
[   11.176038] systemd[1]: Rebuild Hardware Database was skipped because no trigger condition checks were met.
[   11.176878] systemd[1]: Starting Load/Save OS Random Seed...
[   11.177986] systemd[1]: Starting Create System Users...
[   11.178323] systemd[1]: TPM SRK Setup was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
[   11.178434] systemd[1]: Started Journal Service.
[   11.212482] systemd-journald[359]: Received client request to flush runtime journal.
[   13.111156] zram_generator::config[451]: zram0: unknown key compression-algorith, ignoring.
[   13.114461] zram0: detected capacity change from 0 to 10808664
[   13.240524] input: Acer Wireless Radio Control as /devices/LNXSYSTM:00/10251229:00/input/input15
[   13.383926] intel_pmc_core INT33A1:00:  initialized
[   13.423419] i801_smbus 0000:00:1f.4: SPD Write Disable is set
[   13.423464] i801_smbus 0000:00:1f.4: SMBus using PCI interrupt
[   13.430931] i2c i2c-7: Successfully instantiated SPD at 0x50
[   13.493961] mei_me 0000:00:16.0: enabling device (0000 -> 0002)
[   13.513981] Creating 1 MTD partitions on "0000:00:1f.5":
[   13.513987] 0x000000000000-0x000001000000 : "BIOS"
[   13.528892] intel-lpss 0000:00:15.0: enabling device (0000 -> 0002)
[   13.529121] idma64 idma64.0: Found Intel integrated DMA 64-bit
[   13.535740] intel-lpss 0000:00:15.1: enabling device (0000 -> 0002)
[   13.536328] idma64 idma64.1: Found Intel integrated DMA 64-bit
[   13.543617] intel-lpss 0000:00:1e.0: enabling device (0000 -> 0002)
[   13.544106] idma64 idma64.2: Found Intel integrated DMA 64-bit
[   13.545485] Adding 5404328k swap on /dev/zram0.  Priority:100 extents:1 across:5404328k SSDsc
[   13.564065] r8169 0000:07:00.1 eth0: RTL8411b, 98:28:a6:0e:06:bf, XID 5c8, IRQ 146
[   13.564072] r8169 0000:07:00.1 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko]
[   13.607552] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[   13.607706] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[   13.607826] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
[   13.624388] input: ELAN0504:01 04F3:3091 Mouse as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-9/i2c-ELAN0504:01/0018:04F3:3091.0009/input/input16
[   13.624522] input: ELAN0504:01 04F3:3091 Touchpad as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-9/i2c-ELAN0504:01/0018:04F3:3091.0009/input/input18
[   13.624647] hid-generic 0018:04F3:3091.0009: input,hidraw8: I2C HID v1.00 Mouse [ELAN0504:01 04F3:3091] on i2c-ELAN0504:01
[   13.639969] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[   13.639985] cfg80211: failed to load regulatory.db
[   13.686905] RAPL PMU: API unit is 2^-32 Joules, 4 fixed counters, 655360 ms ovfl timer
[   13.686911] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
[   13.686913] RAPL PMU: hw unit of domain package 2^-14 Joules
[   13.686915] RAPL PMU: hw unit of domain dram 2^-14 Joules
[   13.686916] RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules
[   13.708486] cryptd: max_cpu_qlen set to 1000
[   13.714843] acer_wmi: Acer Laptop ACPI-WMI Extras
[   13.714884] acer_wmi: Function bitmap for Communication Button: 0x801
[   13.730725] input: Acer WMI hotkeys as /devices/virtual/input/input19
[   13.745268] Intel(R) Wireless WiFi driver for Linux
[   13.746625] iwlwifi 0000:00:14.3: Detected crf-id 0x2816, cnv-id 0x1000100 wfpm id 0x80000000
[   13.746635] iwlwifi 0000:00:14.3: PCI dev a370/0034, rev=0x312, rfid=0x105110
[   13.770021] iwlwifi 0000:00:14.3: WRT: Overriding region id 0
[   13.770027] iwlwifi 0000:00:14.3: WRT: Overriding region id 1
[   13.770030] iwlwifi 0000:00:14.3: WRT: Overriding region id 2
[   13.770031] iwlwifi 0000:00:14.3: WRT: Overriding region id 3
[   13.770033] iwlwifi 0000:00:14.3: WRT: Overriding region id 4
[   13.770034] iwlwifi 0000:00:14.3: WRT: Overriding region id 6
[   13.770036] iwlwifi 0000:00:14.3: WRT: Overriding region id 8
[   13.770038] iwlwifi 0000:00:14.3: WRT: Overriding region id 9
[   13.770039] iwlwifi 0000:00:14.3: WRT: Overriding region id 10
[   13.770041] iwlwifi 0000:00:14.3: WRT: Overriding region id 11
[   13.770042] iwlwifi 0000:00:14.3: WRT: Overriding region id 15
[   13.770044] iwlwifi 0000:00:14.3: WRT: Overriding region id 16
[   13.770046] iwlwifi 0000:00:14.3: WRT: Overriding region id 18
[   13.770047] iwlwifi 0000:00:14.3: WRT: Overriding region id 19
[   13.770049] iwlwifi 0000:00:14.3: WRT: Overriding region id 20
[   13.770051] iwlwifi 0000:00:14.3: WRT: Overriding region id 21
[   13.770052] iwlwifi 0000:00:14.3: WRT: Overriding region id 28
[   13.770458] iwlwifi 0000:00:14.3: loaded firmware version 46.7e3e4b69.0 9000-pu-b0-jf-b0-46.ucode op_mode iwlmvm
[   13.801867] AVX2 version of gcm_enc/dec engaged.
[   13.801910] AES CTR mode by8 optimization enabled
[   13.804574] Bluetooth: Core ver 2.22
[   13.804598] NET: Registered PF_BLUETOOTH protocol family
[   13.804600] Bluetooth: HCI device and connection manager initialized
[   13.804603] Bluetooth: HCI socket layer initialized
[   13.804606] Bluetooth: L2CAP socket layer initialized
[   13.804610] Bluetooth: SCO socket layer initialized
[   13.858370] ------------[ cut here ]------------
[   13.858373] Unpatched return thunk in use. This should not happen!
[   13.858374] WARNING: CPU: 3 PID: 418 at arch/x86/kernel/cpu/bugs.c:3023 __warn_thunk+0x2a/0x40
[   13.858379] Modules linked in: wl(POE+) snd_seq_device btmtk snd_hwdep aesni_intel bluetooth snd_pcm crypto_simd iwlwifi acer_wmi cryptd snd_timer crc16 platform_profile rapl sparse_keymap snd intel_cstate cfg80211 r8169 realtek intel_lpss_pci wmi_bmof intel_uncore rfkill mdio_devres spi_nor libphy i2c_hid_acpi soundcore mei_me mtd intel_lpss intel_wmi_thunderbolt i2c_hid idma64 acpi_pad mei i2c_i801 i2c_smbus intel_pch_thermal i2c_mux intel_pmc_core intel_vsec pmt_telemetry mac_hid pmt_class pinctrl_cannonlake acer_wireless hid_wiimote ff_memless uinput loop tun i2c_dev crypto_user acpi_call(OE) dm_mod nfnetlink zram ip_tables x_tables hid_generic rtsx_pci_sdmmc serio_raw atkbd mmc_core libps2 vivaldi_fmap sha256_ssse3 spi_intel_pci rtsx_pci spi_intel xhci_pci xhci_pci_renesas i8042 serio uas usb_storage btrfs blake2b_generic libcrc32c crc32c_generic crc32c_intel xor raid6_pq nvme nvme_core nvme_auth usbhid nvidia_drm(POE) nvidia_uvm(POE) nvidia_modeset(POE) nvidia(POE) intel_agp i915 i2c_algo_bit drm_buddy video wmi
[   13.858425]  ttm drm_display_helper cec intel_gtt
[   13.858428] CPU: 3 PID: 418 Comm: (udev-worker) Tainted: P     U     OE      6.10.6-zen1-1-zen #1 ee81b56be11bce761cff661f9e15368bf5a1ae77
[   13.858431] Hardware name: Acer Nitro AN515-53/Freed_CFS, BIOS V1.28 08/05/2019
[   13.858432] RIP: 0010:__warn_thunk+0x2a/0x40
[   13.858434] Code: 66 0f 1f 00 0f 1f 44 00 00 80 3d a0 67 37 02 00 74 05 c3 cc cc cc cc 48 c7 c7 48 f0 25 9c c6 05 8b 67 37 02 01 e8 76 9e 06 00 <0f> 0b c3 cc cc cc cc 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00
[   13.858435] RSP: 0018:ffffb6fc0295f980 EFLAGS: 00010286
[   13.858437] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000027
[   13.858438] RDX: ffff9550de3a19c8 RSI: 0000000000000001 RDI: ffff9550de3a19c0
[   13.858439] RBP: ffffb6fc0295f9d0 R08: ffffffff9cab2688 R09: 00000000ffffefff
[   13.858440] R10: 0000000000000003 R11: 0000000000000002 R12: ffffffffc695aac1
[   13.858442] R13: ffffb6fc0295fa18 R14: ffff954d81123000 R15: ffff954d9fa4e438
[   13.858443] FS:  00007bd4f9153880(0000) GS:ffff9550de380000(0000) knlGS:0000000000000000
[   13.858444] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   13.858445] CR2: 00005a8168ca4758 CR3: 000000011c15e003 CR4: 00000000003706f0
[   13.858447] Call Trace:
[   13.858448]  <TASK>
[   13.858449]  ? __warn_thunk+0x2a/0x40
[   13.858451]  ? __warn.cold+0x8e/0xf3
[   13.858455]  ? __warn_thunk+0x2a/0x40
[   13.858457]  ? report_bug+0xe7/0x210
[   13.858458]  ? console_unlock+0x84/0x130
[   13.858461]  ? handle_bug+0x3c/0x80
[   13.858463]  ? exc_invalid_op+0x19/0xc0
[   13.858465]  ? asm_exc_invalid_op+0x1a/0x20
[   13.858468]  ? __warn_thunk+0x2a/0x40
[   13.858469]  warn_thunk_thunk+0x1a/0x30
[   13.858472]  getvar+0x20/0x70 [wl 48c8f375f35649b4a4b254f6ab76d23274c7d9ca]
[   13.858506]  ? __UNIQUE_ID_vermagic434+0x4903c1309ff3/0x4903c1309ff3 [wl 48c8f375f35649b4a4b254f6ab76d23274c7d9ca]
[   13.858536]  wl_module_init+0x17/0xa0 [wl 48c8f375f35649b4a4b254f6ab76d23274c7d9ca]
[   13.858565]  ? do_one_initcall+0x58/0x310
[   13.858569]  ? do_init_module+0x60/0x220
[   13.858571]  ? idempotent_init_module+0x182/0x3a0
[   13.858575]  ? __x64_sys_finit_module+0x5e/0xb0
[   13.858578]  ? do_syscall_64+0x82/0x190
[   13.858581]  ? vfs_read+0x1da/0x470
[   13.858583]  ? vfs_read+0x1da/0x470
[   13.858584]  ? __rseq_handle_notify_resume+0x23f/0x510
[   13.858587]  ? switch_fpu_return+0x4e/0xd0
[   13.858589]  ? syscall_exit_to_user_mode+0x72/0x1e0
[   13.858592]  ? do_syscall_64+0x8e/0x190
[   13.858593]  ? syscall_exit_to_user_mode+0x72/0x1e0
[   13.858594]  ? do_syscall_64+0x8e/0x190
[   13.858596]  ? syscall_exit_to_user_mode+0x72/0x1e0
[   13.858598]  ? do_syscall_64+0x8e/0x190
[   13.858599]  ? syscall_exit_to_user_mode+0x72/0x1e0
[   13.858601]  ? do_syscall_64+0x8e/0x190
[   13.858602]  ? do_syscall_64+0x8e/0x190
[   13.858603]  ? exc_page_fault+0x81/0x190
[   13.858605]  ? entry_SYSCALL_64_after_hwframe+0x76/0x7e
[   13.858608]  </TASK>
[   13.858609] ---[ end trace 0000000000000000 ]---
[   13.859025] pps_core: LinuxPPS API ver. 1 registered
[   13.859027] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[   13.870420] mousedev: PS/2 mouse device common for all mice
[   13.876531] PTP clock support registered
[   13.885056] BTRFS: device label crucial devid 1 transid 126756 /dev/sda1 (8:1) scanned by mount (658)
[   13.886257] BTRFS info (device sda1): first mount of filesystem 6a4e9303-8851-471e-b698-bec1645dc445
[   13.886268] BTRFS info (device sda1): using crc32c (crc32c-intel) checksum algorithm
[   13.886272] BTRFS info (device sda1): using free-space-tree
[   13.910072] mc: Linux media interface: v0.10
[   13.933045] ee1004 7-0050: 512 byte EE1004-compliant SPD EEPROM, read-only
[   13.967048] r8169 0000:07:00.1 enp7s0f1: renamed from eth0
[   14.002848] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[   14.003392] videodev: Linux video capture interface: v2.00
[   14.011531] usbcore: registered new interface driver btusb
[   14.059108] usb 2-1.1.4: Warning! Unlikely big volume range (=511), cval->res is probably wrong.
[   14.059112] usb 2-1.1.4: [15] FU [USB AUDIO Playback Volume] ch = 6, val = -8176/0/16
[   14.059663] usb 2-1.1.4: Warning! Unlikely big volume range (=767), cval->res is probably wrong.
[   14.059666] usb 2-1.1.4: [12] FU [Mic Capture Volume] ch = 2, val = -4592/7680/16
[   14.060314] usb 1-1.1.3: Quirk or no altset; falling back to MIDI 1.0
[   14.060777] usbcore: registered new interface driver snd-usb-audio
[   14.063238] Bluetooth: hci0: Found device firmware: intel/ibt-17-16-1.sfi
[   14.063332] Bluetooth: hci0: Boot Address: 0x40800
[   14.063334] Bluetooth: hci0: Firmware Version: 201-12.24
[   14.063336] Bluetooth: hci0: Firmware already loaded
[   14.063344] input: ELAN0504:01 04F3:3091 Mouse as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-9/i2c-ELAN0504:01/0018:04F3:3091.0009/input/input20
[   14.065227] Bluetooth: hci0: HCI LE Coded PHY feature bit is set, but its usage is not supported.
[   14.066465] input: ELAN0504:01 04F3:3091 Touchpad as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-9/i2c-ELAN0504:01/0018:04F3:3091.0009/input/input22
[   14.069278] hid-multitouch 0018:04F3:3091.0009: input,hidraw8: I2C HID v1.00 Mouse [ELAN0504:01 04F3:3091] on i2c-ELAN0504:01
[   14.138371] iTCO_vendor_support: vendor-support=0
[   14.144594] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
[   14.144825] dw-apb-uart.2: ttyS4 at MMIO 0x8f802000 (irq = 20, base_baud = 7500000) is a 16550A
[   14.168940] iwlwifi 0000:00:14.3: Detected Intel(R) Wireless-AC 9560 160MHz, REV=0x312
[   14.217901] iwlwifi 0000:00:14.3: base HW address: b4:6b:fc:15:73:db, OTP minor version: 0x4
[   14.253054] iTCO_wdt iTCO_wdt: Found a Intel PCH TCO device (Version=6, TCOBASE=0x0400)
[   14.253176] iTCO_wdt iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   14.264023] snd_hda_codec_realtek hdaudioC4D0: autoconfig for ALC255: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[   14.264029] snd_hda_codec_realtek hdaudioC4D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   14.264032] snd_hda_codec_realtek hdaudioC4D0:    hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[   14.264034] snd_hda_codec_realtek hdaudioC4D0:    mono: mono_out=0x0
[   14.264036] snd_hda_codec_realtek hdaudioC4D0:    inputs:
[   14.264037] snd_hda_codec_realtek hdaudioC4D0:      Headset Mic=0x19
[   14.264039] snd_hda_codec_realtek hdaudioC4D0:      Internal Mic=0x12
[   14.285901] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs'
[   14.288724] iwlwifi 0000:00:14.3 wlp0s20f3: renamed from wlan0
[   14.305768] Adding 5242876k swap on /dev/sdb3.  Priority:-2 extents:1 across:5242876k SS
[   14.326609] usb 1-5: Found UVC 1.00 device HD WebCam (04f2:b5f7)
[   14.344164] usbcore: registered new interface driver uvcvideo
[   14.374767] BTRFS: device label sfhome devid 1 transid 1035776 /dev/sdb5 (8:21) scanned by mount (802)
[   14.375682] BTRFS info (device sdb5): first mount of filesystem 9725d41a-8f03-49c0-800b-e89e64291fe8
[   14.375691] BTRFS info (device sdb5): using crc32c (crc32c-intel) checksum algorithm
[   14.375695] BTRFS info (device sdb5): using free-space-tree
[   14.386350] intel_tcc_cooling: TCC Offset locked
[   14.607439] intel_rapl_common: Found RAPL domain package
[   14.607442] intel_rapl_common: Found RAPL domain core
[   14.607443] intel_rapl_common: Found RAPL domain uncore
[   14.607444] intel_rapl_common: Found RAPL domain dram
[   14.819479] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1f.3/sound/card4/input23
[   14.904782] usb 1-1.1.2: received EP1 urb->status = -2
[   14.904818] usb 1-1.1.2: unable to init card! (ret=-19)
[   14.904945] usbcore: registered new interface driver snd-usb-caiaq
[   19.077048] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   19.077057] Bluetooth: BNEP filters: protocol multicast
[   19.077066] Bluetooth: BNEP socket layer initialized
[   19.174894] Bluetooth: MGMT ver 1.22
[   19.183215] NET: Registered PF_ALG protocol family
[   20.868653] Generic FE-GE Realtek PHY r8169-0-701:00: attached PHY driver (mii_bus:phy_addr=r8169-0-701:00, irq=MAC)
[   21.036901] r8169 0000:07:00.1 enp7s0f1: Link is Down
[   21.245306] iwlwifi 0000:00:14.3: Registered PHC clock: iwlwifi-PTP, with index: 0
[   21.616569] 8021q: 802.1Q VLAN Support v1.8
[   21.920289] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[   22.738765] evdi: [I] Initialising logging on level 4
[   22.738769] evdi: [I] Atomic driver: yes
[   25.379708] kvm_intel: L1TF CPU bug present and SMT on, data leak possible. See CVE-2018-3646 and https://www.kernel.org/doc/html/latest/admin-guide/hw-vuln/l1tf.html for details.
[   26.105379] wlp0s20f3: authenticate with 14:21:03:13:f6:7e (local address=b4:6b:fc:15:73:db)
[   26.106399] wlp0s20f3: send auth to 14:21:03:13:f6:7e (try 1/3)
[   26.151603] wlp0s20f3: authenticated
[   26.152708] wlp0s20f3: associate with 14:21:03:13:f6:7e (try 1/3)
[   26.165745] wlp0s20f3: RX AssocResp from 14:21:03:13:f6:7e (capab=0x1431 status=0 aid=6)
[   26.169221] wlp0s20f3: associated
[   26.171050] br0: port 1(wlp0s20f3.2) entered blocking state
[   26.171054] br0: port 1(wlp0s20f3.2) entered disabled state
[   26.171061] wlp0s20f3.2: entered allmulticast mode
[   26.171064] iwlwifi 0000:00:14.3 wlp0s20f3: entered allmulticast mode
[   26.171113] wlp0s20f3.2: entered promiscuous mode
[   26.171116] iwlwifi 0000:00:14.3 wlp0s20f3: entered promiscuous mode
[   26.211628] wlp0s20f3: Limiting TX power to 30 (30 - 0) dBm as advertised by 14:21:03:13:f6:7e
[   26.355080] br0: port 1(wlp0s20f3.2) entered blocking state
[   26.355088] br0: port 1(wlp0s20f3.2) entered forwarding state
[   29.212820] capability: warning: `zerotier-one' uses 32-bit capabilities (legacy support in use)
[   40.145002] usb 1-1.3.4: reset full-speed USB device number 12 using xhci_hcd
[   57.465480] wlp0s20f3: disconnect from AP 14:21:03:13:f6:7e for new auth to 14:21:03:13:f6:7f
[   57.465976] br0: port 1(wlp0s20f3.2) entered disabled state
[   57.500225] wlp0s20f3: authenticate with 14:21:03:13:f6:7f (local address=b4:6b:fc:15:73:db)
[   57.501757] wlp0s20f3: send auth to 14:21:03:13:f6:7f (try 1/3)
[   57.543297] wlp0s20f3: authenticated
[   57.544692] wlp0s20f3: associate with 14:21:03:13:f6:7f (try 1/3)
[   57.554534] wlp0s20f3: RX ReassocResp from 14:21:03:13:f6:7f (capab=0x1511 status=0 aid=5)
[   57.557613] wlp0s20f3: associated
[   57.603429] br0: port 1(wlp0s20f3.2) entered blocking state
[   57.603444] br0: port 1(wlp0s20f3.2) entered forwarding state
[   57.645277] wlp0s20f3: Limiting TX power to 30 (30 - 0) dBm as advertised by 14:21:03:13:f6:7f
[   71.493900] input: ydotoold virtual device as /devices/virtual/input/input24
[   74.476831] Bluetooth: RFCOMM TTY layer initialized
[   74.476838] Bluetooth: RFCOMM socket layer initialized
[   74.476840] Bluetooth: RFCOMM ver 1.11
[   87.079635] sched: RT throttling activated
[   91.138988] block nvme0n1: No UUID available providing old NGUID
[   96.754255] input: Logitech Wireless Mouse PID:4038 as /devices/virtual/input/input25
[   96.754971] input: Mouse passthrough as /devices/virtual/input/input26
[   96.755307] input: Keyboard passthrough as /devices/virtual/input/input27
[  100.723150] input: XP-Pen Pen as /devices/virtual/input/input28
[  100.723529] input: XP-Pen Mouse as /devices/virtual/input/input29
[  100.723667] input: XP-Pen Eraser as /devices/virtual/input/input30
[  102.060409] warning: `ThreadPoolForeg' uses wireless extensions which will stop working for Wi-Fi 7 hardware; use nl80211

If you need any more details just let me know, and I'll try to provide them.
Any help is greatly appreciated, and thank you for your time.

Last edited by FungiKin (2024-08-30 00:09:06)

Offline

#2 2024-08-29 17:36:22

gromit
Package Maintainer (PM)
From: Germany
Registered: 2024-02-10
Posts: 665
Website

Re: [SOLVED] Native Instruments Audio 8 DJ/snd_usb_caiaq stopped working

Is this issue specific to the linux-zen kernel or does it also occur with the linux kernel package?

Also you could try the linux-lts kernel package smile

Offline

#3 2024-08-29 20:54:50

FungiKin
Member
From: USA, North America, Earth
Registered: 2023-03-30
Posts: 8

Re: [SOLVED] Native Instruments Audio 8 DJ/snd_usb_caiaq stopped working

The kernels I've tested are linux-zen, linux-lts, and linux-rt, however the driver issue occurs on all of them, I'll test with the normal kernel, and provide an update.
UPDATE/EDIT:
normal/default linux kernel also has the issue

Last edited by FungiKin (2024-08-29 21:46:08)

Offline

#4 2024-08-30 00:08:36

FungiKin
Member
From: USA, North America, Earth
Registered: 2023-03-30
Posts: 8

Re: [SOLVED] Native Instruments Audio 8 DJ/snd_usb_caiaq stopped working

I kind of solved it, I tested it on a system that hadn't been updated in awhile, as well as Debian install, and it turns out that my Native Instruments Audio 8 DJ is just dead... sorry for wasting your time, but thank you for the help.

Offline

Board footer

Powered by FluxBB