Arch Linux

vikingr

Member

From: Germany

Registered: 2007-01-02

Posts: 3

Problems with gphoto2 and Panasonic DMC-LX2

Hello,

when I try to get the images of my Panasonic Lumix DMC-LX2 with gphoto2,
I get the following errors:

*** Error ***              
PTP I/O error
24.449972 gphoto2-port(2): Closing port...
24.452140 context(0): An error occurred in the io-library ('Unspecified error'): Could not query kernel driver of device.

*** Error ***              
An error occurred in the io-library ('Unspecified error'): Could not query kernel driver of device.
*** Error (-1: 'Unspecified error') ***

The output of gphoto2 --auto-detect is:

Model                          Port                                            
----------------------------------------------------------
Panasonic DMC-FZ20 (alternate id) usb:            
Panasonic DMC-FZ20 (alternate id) usb:003,009

The output of gphoto2 --debug -P is here: http://pastebin.com/870763

This is the output of dmesg when I plug in the camera:

usb 3-2: new full speed USB device using uhci_hcd and address 10
usb 3-2: configuration #1 chosen from 1 choice
scsi11 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 10
usb-storage: waiting for device to settle before scanning
scsi 11:0:0:0: Direct-Access     MATSHITA DMC-LX2          0100 PQ: 0 ANSI: 2
SCSI device sdb: 990975 512-byte hdwr sectors (507 MB)
sdb: Write Protect is off
sdb: Mode Sense: 04 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 990975 512-byte hdwr sectors (507 MB)
sdb: Write Protect is off
sdb: Mode Sense: 04 00 00 00
sdb: assuming drive cache: write through
 sdb: sdb1
 sdb: p1 exceeds device capacity
sd 11:0:0:0: Attached scsi removable disk sdb
sd 11:0:0:0: Attached scsi generic sg2 type 0
usb-storage: device scan complete
attempt to access beyond end of device
sdb: rw=0, want=990976, limit=990975
printk: 6 messages suppressed.
Buffer I/O error on device sdb1, logical block 990738
attempt to access beyond end of device
sdb: rw=0, want=990976, limit=990975
Buffer I/O error on device sdb1, logical block 990738
attempt to access beyond end of device
sdb: rw=0, want=990976, limit=990975
Buffer I/O error on device sdb1, logical block 990738
attempt to access beyond end of device
sdb: rw=0, want=990976, limit=990975
Buffer I/O error on device sdb1, logical block 990738
attempt to access beyond end of device
sdb: rw=0, want=990976, limit=990975
Buffer I/O error on device sdb1, logical block 990738
attempt to access beyond end of device
sdb: rw=0, want=990976, limit=990975
Buffer I/O error on device sdb1, logical block 990738
attempt to access beyond end of device
sdb: rw=0, want=990976, limit=990975
Buffer I/O error on device sdb1, logical block 990738
attempt to access beyond end of device
sdb: rw=0, want=990976, limit=990975
Buffer I/O error on device sdb1, logical block 990738
attempt to access beyond end of device
sdb: rw=0, want=990976, limit=990975
Buffer I/O error on device sdb1, logical block 990738
attempt to access beyond end of device
sdb: rw=0, want=990976, limit=990975
Buffer I/O error on device sdb1, logical block 990738
attempt to access beyond end of device
sdb: rw=0, want=990976, limit=990975
attempt to access beyond end of device
sdb: rw=0, want=990976, limit=990975
attempt to access beyond end of device
sdb: rw=0, want=990976, limit=990975
attempt to access beyond end of device
sdb: rw=0, want=990976, limit=990975
attempt to access beyond end of device
sdb: rw=0, want=990976, limit=990975
attempt to access beyond end of device
sdb: rw=0, want=990976, limit=990975

I ran everything as root to make sure it isn't a rights problem.

I can load the images of my older Canon Ixus 30 cam and the cam works with my
Mac, so it's no hardware issue.

Thanks in advance!

Last edited by vikingr (2007-01-29 23:35:59)