HDMI no signal after kernel update

pmarcinek · 2025-12-02 15:43:21

Hello,
i was successfully running Arch Linux on GIGABYTE-BACE-3160 on kernel <=6.5. I used i915 kernel module to utilize HDMI/VGA output. Everything worked great until i installed new system with the newest kernel.

Linux archlinux 6.17.9-arch1-1 #1 SMP PREEMPT_DYNAMIC Mon, 24 Nov 2025 15:21:09 +0000 x86_64 GNU/Linux

As a result i can see connected output:

[root@archlinux card1-HDMI-A-2]# xrandr -q
Screen 0: minimum 8 x 8, current 1920 x 1080, maximum 32767 x 32767
DP1 disconnected (normal left inverted right x axis y axis)
DP2 disconnected (normal left inverted right x axis y axis)
DP3 disconnected (normal left inverted right x axis y axis)
HDMI1 disconnected (normal left inverted right x axis y axis)
HDMI2 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 480mm x 270mm
   1920x1080     60.00*+
   1680x1050     59.88  
   1600x900      60.00  
   1280x1024     75.02    60.02  
   1280x800      59.91  
   1152x864      75.00  
   1280x720      60.00  
   1024x768      75.03    60.00  
   832x624       74.55  
   800x600       75.00    60.32  
   640x480       75.00    59.94  
   720x400       70.08  
VIRTUAL1 disconnected (normal left inverted right x axis y axis)

but i have no output on my monitor (monitor and cable is working properly with different HW).

Current kernel parameters:

BOOT_IMAGE=/vmlinuz-linux root=UUID=16fda6ab-dd65-4bd1-8a49-ab8b63099b4c rw loglevel=3 i915.nuclear_pageflip=1 i915.force_probe=22b1 ipv6.disable=1 intel_idle.max_cstate=1 i915.enable_dc=0 i915.enable_fbc=0 i915.enable_psr=0

X server configuration:

Section "Device"
        Identifier "Intel Graphics"
        Driver "intel"
        Option "DRI" "True"
        Option "TearFree" "True"
        Option "AccelMethod" "sna"
EndSection

X logs:

[     9.968] 
X.Org X Server 1.21.1.21
X Protocol Version 11, Revision 0
[     9.968] Current Operating System: Linux archlinux 6.17.9-arch1-1 #1 SMP PREEMPT_DYNAMIC Mon, 24 Nov 2025 15:21:09 +0000 x86_64
[     9.968] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=16fda6ab-dd65-4bd1-8a49-ab8b63099b4c rw loglevel=3 i915.nuclear_pageflip=1 i915.force_probe=22b1 ipv6.disable=1 intel_idle.max_cstate=1 i915.enable_dc=0 i915.enable_fbc=0 i915.enable_psr=0
[     9.968]  
[     9.968] Current version of pixman: 0.46.4
[     9.968]    Before reporting problems, check [url]http://wiki.x.org[/url]
        to make sure that you have the latest version.
[     9.968] Markers: (--) probed, (**) from config file, (==) default setting,
        (++) from command line, (!!) notice, (II) informational,
        (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[     9.968] (==) Log file: "/var/log/Xorg.0.log", Time: Tue Dec  2 15:16:32 2025
[     9.972] (==) Using config directory: "/etc/X11/xorg.conf.d"
[     9.972] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[     9.972] (==) No Layout section.  Using the first Screen section.
[     9.972] (==) No screen section available. Using defaults.
[     9.972] (**) |-->Screen "Default Screen Section" (0)
[     9.972] (**) |   |-->Monitor "<default monitor>"
[     9.974] (==) No device specified for screen "Default Screen Section".
        Using the first device section listed.
[     9.974] (**) |   |-->Device "Intel Graphics"
[     9.974] (==) No monitor specified for screen "Default Screen Section".
        Using a default monitor configuration.
[     9.974] (**) Allowing byte-swapped clients
[     9.974] (==) Automatically adding devices
[     9.974] (==) Automatically enabling devices
[     9.974] (==) Automatically adding GPU devices
[     9.974] (==) Automatically binding GPU devices
[     9.974] (==) Max clients allowed: 256, resource mask: 0x1fffff
[     9.976] (WW) The directory "/usr/share/fonts/misc" does not exist.
[     9.976]    Entry deleted from font path.
[     9.976] (WW) The directory "/usr/share/fonts/TTF" does not exist.
[     9.976]    Entry deleted from font path.
[     9.976] (WW) The directory "/usr/share/fonts/OTF" does not exist.
[     9.976]    Entry deleted from font path.
[     9.976] (WW) The directory "/usr/share/fonts/Type1" does not exist.
[     9.976]    Entry deleted from font path.
[     9.976] (WW) The directory "/usr/share/fonts/100dpi" does not exist.
[     9.976]    Entry deleted from font path.
[     9.976] (WW) The directory "/usr/share/fonts/75dpi" does not exist.
[     9.976]    Entry deleted from font path.
[     9.976] (==) FontPath set to:[/em]
[     9.976] (==) ModulePath set to "/usr/lib/xorg/modules"
[     9.976] (II) The server relies on udev to provide the list of input devices.
        If no devices become available, reconfigure udev or disable AutoAddDevices.
[     9.976] (II) Module ABI versions:
[     9.976]    X.Org ANSI C Emulation: 0.4
[     9.976]    X.Org Video Driver: 25.2
[     9.976]    X.Org XInput driver : 24.4
[     9.976]    X.Org Server Extension : 10.0
[     9.977] (++) using VT number 7[/em]
[     9.977] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[     9.981] (II) xfree86: Adding drm device (/dev/dri/card1)
[     9.981] (II) Platform probe for /sys/devices/pci0000:00/0000:00:02.0/drm/card1
[     9.998] (--) PCI:*(0@0:2:0) 8086:22b1:1458:1000 rev 53, Mem @ 0x80000000/16777216, 0x90000000/268435456, I/O @ 0x0000f000/64, BIOS @ 0x????????/131072
[     9.998] (II) LoadModule: "glx"
[     9.999] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[    10.011] (II) Module glx: vendor="X.Org Foundation"
[    10.011]    compiled for 1.21.1.21, module version = 1.0.0
[    10.011]    ABI class: X.Org Server Extension, version 10.0
[    10.011] (II) LoadModule: "intel"
[    10.012] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[    10.015] (II) Module intel: vendor="X.Org Foundation"
[    10.015]    compiled for 1.21.1.16, module version = 2.99.917
[    10.015]    Module class: X.Org Video Driver
[    10.015]    ABI class: X.Org Video Driver, version 25.2
[    10.015] (II) intel: Driver for Intel(R) Integrated Graphics Chipsets:
        i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G,
        915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM,
        Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
        GM45, 4 Series, G45/G43, Q45/Q43, G41, B43
[    10.016] (II) intel: Driver for Intel(R) HD Graphics
[    10.016] (II) intel: Driver for Intel(R) Iris(TM) Graphics
[    10.016] (II) intel: Driver for Intel(R) Iris(TM) Pro Graphics
[    10.029] (II) intel(0): Using Kernel Mode Setting driver: i915, version 1.6.0 0
[    10.029] (II) intel(0): SNA compiled from 2.99.917-939-g4a64400e
[    10.032] (--) intel(0): Integrated Graphics Chipset: Intel(R) HD Graphics
[    10.032] (--) intel(0): CPU: x86-64, sse2, sse3, ssse3, sse4.1, sse4.2; using a maximum of 4 threads
[    10.032] (II) intel(0): Creating default Display subsection in Screen section
        "Default Screen Section" for depth/fbbpp 24/32
[    10.032] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[    10.032] (==) intel(0): RGB weight 888
[    10.032] (==) intel(0): Default visual is TrueColor
[    10.032] (**) intel(0): Option "AccelMethod" "sna"
[    10.032] (**) intel(0): Option "DRI" "True"
[    10.033] (**) intel(0): Option "TearFree" "True"
[    10.035] (II) intel(0): Output DP1 has no monitor section
[    10.035] (II) intel(0): Enabled output DP1
[    10.035] (II) intel(0): Output HDMI1 has no monitor section
[    10.036] (II) intel(0): Enabled output HDMI1
[    10.036] (II) intel(0): Output DP2 has no monitor section
[    10.036] (II) intel(0): Enabled output DP2
[    10.036] (II) intel(0): Output HDMI2 has no monitor section
[    10.037] (II) intel(0): Enabled output HDMI2
[    10.037] (II) intel(0): Output DP3 has no monitor section
[    10.037] (II) intel(0): Enabled output DP3
[    10.037] (--) intel(0): Using a maximum size of 256x256 for hardware cursors
[    10.037] (II) intel(0): Output VIRTUAL1 has no monitor section
[    10.037] (II) intel(0): Enabled output VIRTUAL1
[    10.037] (--) intel(0): Output HDMI2 using initial mode 1920x1080 on crtc 0
[    10.038] (**) intel(0): TearFree enabled
[    10.038] (==) intel(0): Using gamma correction (1.0, 1.0, 1.0)
[    10.038] (==) intel(0): DPI set to (96, 96)
[    10.038] (II) Loading sub module "dri3"
[    10.038] (II) LoadModule: "dri3"
[    10.038] (II) Module "dri3" already built-in
[    10.038] (II) Loading sub module "dri2"
[    10.038] (II) LoadModule: "dri2"
[    10.038] (II) Module "dri2" already built-in
[    10.038] (II) Loading sub module "present"
[    10.038] (II) LoadModule: "present"
[    10.038] (II) Module "present" already built-in
[    10.042] (II) intel(0): SNA initialized with Cherryview (gen8) backend
[    10.042] (==) intel(0): Backing store enabled
[    10.042] (==) intel(0): Silken mouse enabled
[    10.042] (II) intel(0): HW Cursor enabled
[    10.044] (==) intel(0): DPMS enabled
[    10.044] (==) intel(0): Display hotplug detection enabled
[    10.045] (II) intel(0): [DRI2] Setup complete
[    10.045] (II) intel(0): [DRI2]   DRI driver: i965
[    10.045] (II) intel(0): [DRI2]   VDPAU driver: va_gl
[    10.046] (II) intel(0): direct rendering: DRI2 DRI3 enabled
[    10.046] (II) intel(0): hardware support for Present enabled
[    10.046] (II) Initializing extension Generic Event Extension
[    10.046] (II) Initializing extension SHAPE
[    10.046] (II) Initializing extension MIT-SHM
[    10.047] (II) Initializing extension XInputExtension
[    10.047] (II) Initializing extension XTEST
[    10.047] (II) Initializing extension BIG-REQUESTS
[    10.048] (II) Initializing extension SYNC
[    10.048] (II) Initializing extension XKEYBOARD
[    10.049] (II) Initializing extension XC-MISC
[    10.049] (II) Initializing extension SECURITY
[    10.049] (II) Initializing extension XFIXES
[    10.050] (II) Initializing extension RENDER
[    10.050] (II) Initializing extension RANDR
[    10.051] (II) Initializing extension COMPOSITE
[    10.051] (II) Initializing extension DAMAGE
[    10.052] (II) Initializing extension MIT-SCREEN-SAVER
[    10.053] (II) Initializing extension DOUBLE-BUFFER
[    10.053] (II) Initializing extension RECORD
[    10.053] (II) Initializing extension DPMS
[    10.054] (II) Initializing extension Present
[    10.054] (II) Initializing extension DRI3
[    10.054] (II) Initializing extension X-Resource
[    10.055] (II) Initializing extension XVideo
[    10.055] (II) Initializing extension XVideo-MotionCompensation
[    10.055] (II) Initializing extension GLX
[    10.057] (EE) AIGLX error: dlopen of /usr/lib/dri/i965_dri.so failed (/usr/lib/dri/i965_dri.so: cannot open shared object file: No such file or directory)
[    10.057] (EE) AIGLX error: unable to load driver i965
[    10.363] (II) IGLX: Loaded and initialized swrast
[    10.363] (II) GLX: Initialized DRISWRAST GL provider for screen 0
[    10.363] (II) Initializing extension XFree86-VidModeExtension
[    10.363] (II) Initializing extension XFree86-DGA
[    10.364] (II) Initializing extension XFree86-DRI
[    10.364] (II) Initializing extension DRI2
[    10.378] (II) intel(0): switch to mode 1920x1080@60.0 on HDMI2 using crtc 0, position (0, 0), rotation normal, reflection none
[    10.408] (II) intel(0): Setting screen physical size to 508 x 285
[    10.660] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[    10.660] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[    10.660] (II) LoadModule: "libinput"
[    10.661] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so
[    10.691] (II) Module libinput: vendor="X.Org Foundation"
[    10.691]    compiled for 1.21.1.13, module version = 1.5.0
[    10.691]    Module class: X.Org XInput Driver
[    10.692]    ABI class: X.Org XInput driver, version 24.4
[    10.692] (II) Using input driver 'libinput' for 'Power Button'
[    10.692] (**) Power Button: always reports core events
[    10.692] (**) Option "Device" "/dev/input/event2"
[    10.707] (II) event2  - Power Button: is tagged by udev as: Keyboard
[    10.707] (II) event2  - Power Button: device is a keyboard
[    10.707] (II) event2  - Power Button: device removed
[    10.716] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2/event2"
[    10.716] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[    10.719] (II) event2  - Power Button: is tagged by udev as: Keyboard
[    10.719] (II) event2  - Power Button: device is a keyboard
[    10.722] (II) config/udev: Adding input device Video Bus (/dev/input/event7)
[    10.722] (**) Video Bus: Applying InputClass "libinput keyboard catchall"
[    10.722] (II) Using input driver 'libinput' for 'Video Bus'
[    10.722] (**) Video Bus: always reports core events
[    10.722] (**) Option "Device" "/dev/input/event7"
[    10.725] (II) event7  - Video Bus: is tagged by udev as: Keyboard
[    10.725] (II) event7  - Video Bus: device is a keyboard
[    10.725] (II) event7  - Video Bus: device removed
[    10.748] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input21/event7"
[    10.748] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[    10.754] (II) event7  - Video Bus: is tagged by udev as: Keyboard
[    10.754] (II) event7  - Video Bus: device is a keyboard
[    10.758] (II) config/udev: Adding input device Power Button (/dev/input/event0)
[    10.758] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[    10.758] (II) Using input driver 'libinput' for 'Power Button'
[    10.758] (**) Power Button: always reports core events
[    10.758] (**) Option "Device" "/dev/input/event0"
[    10.763] (II) event0  - Power Button: is tagged by udev as: Keyboard
[    10.763] (II) event0  - Power Button: device is a keyboard
[    10.764] (II) event0  - Power Button: device removed
[    10.777] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0/event0"
[    10.777] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[    10.783] (II) event0  - Power Button: is tagged by udev as: Keyboard
[    10.784] (II) event0  - Power Button: device is a keyboard
[    10.788] (II) config/udev: Adding input device Sleep Button (/dev/input/event1)
[    10.788] (**) Sleep Button: Applying InputClass "libinput keyboard catchall"
[    10.788] (II) Using input driver 'libinput' for 'Sleep Button'
[    10.788] (**) Sleep Button: always reports core events
[    10.788] (**) Option "Device" "/dev/input/event1"
[    10.793] (II) event1  - Sleep Button: is tagged by udev as: Keyboard
[    10.794] (II) event1  - Sleep Button: device is a keyboard
[    10.794] (II) event1  - Sleep Button: device removed
[    10.802] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1/event1"
[    10.802] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 9)
[    10.807] (II) event1  - Sleep Button: is tagged by udev as: Keyboard
[    10.808] (II) event1  - Sleep Button: device is a keyboard
[    10.819] (II) config/udev: Adding input device Logitech Wireless Keyboard PID:4023 (/dev/input/event4)
[    10.819] (**) Logitech Wireless Keyboard PID:4023: Applying InputClass "libinput keyboard catchall"
[    10.819] (II) Using input driver 'libinput' for 'Logitech Wireless Keyboard PID:4023'
[    10.819] (**) Logitech Wireless Keyboard PID:4023: always reports core events
[    10.819] (**) Option "Device" "/dev/input/event4"
[    10.829] (II) event4  - Logitech Wireless Keyboard PID:4023: is tagged by udev as: Keyboard
[    10.830] (II) event4  - Logitech Wireless Keyboard PID:4023: device is a keyboard
[    10.831] (II) event4  - Logitech Wireless Keyboard PID:4023: device removed
[    10.841] (II) libinput: Logitech Wireless Keyboard PID:4023: needs a virtual subdevice
[    10.841] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.1/0003:046D:C534.0002/0003:046D:4023.0003/input/input20/event4"
[    10.841] (II) XINPUT: Adding extended input device "Logitech Wireless Keyboard PID:4023" (type: MOUSE, id 10)
[    10.841] (**) Option "AccelerationScheme" "none"
[    10.841] (**) Logitech Wireless Keyboard PID:4023: (accel) selected scheme none/0
[    10.841] (**) Logitech Wireless Keyboard PID:4023: (accel) acceleration factor: 2.000
[    10.841] (**) Logitech Wireless Keyboard PID:4023: (accel) acceleration threshold: 4
[    10.850] (II) event4  - Logitech Wireless Keyboard PID:4023: is tagged by udev as: Keyboard
[    10.851] (II) event4  - Logitech Wireless Keyboard PID:4023: device is a keyboard
[    10.858] (II) config/udev: Adding input device Logitech Wireless Mouse (/dev/input/event5)
[    10.858] (**) Logitech Wireless Mouse: Applying InputClass "libinput pointer catchall"
[    10.858] (**) Logitech Wireless Mouse: Applying InputClass "libinput keyboard catchall"
[    10.858] (II) Using input driver 'libinput' for 'Logitech Wireless Mouse'
[    10.858] (**) Logitech Wireless Mouse: always reports core events
[    10.858] (**) Option "Device" "/dev/input/event5"
[    10.867] (II) event5  - Logitech Wireless Mouse: is tagged by udev as: Keyboard Mouse
[    10.868] (II) event5  - Logitech Wireless Mouse: device is a pointer
[    10.868] (II) event5  - Logitech Wireless Mouse: device is a keyboard
[    10.869] (II) event5  - Logitech Wireless Mouse: device removed
[    10.878] (II) libinput: Logitech Wireless Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[    10.878] (II) libinput: Logitech Wireless Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[    10.878] (II) libinput: Logitech Wireless Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[    10.878] (II) libinput: Logitech Wireless Mouse: needs a virtual subdevice
[    10.878] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.1/0003:046D:C534.0002/0003:046D:4091.0004/input/input22/event5"
[    10.878] (II) XINPUT: Adding extended input device "Logitech Wireless Mouse" (type: MOUSE, id 11)
[    10.879] (**) Option "AccelerationScheme" "none"
[    10.879] (**) Logitech Wireless Mouse: (accel) selected scheme none/0
[    10.879] (**) Logitech Wireless Mouse: (accel) acceleration factor: 2.000
[    10.879] (**) Logitech Wireless Mouse: (accel) acceleration threshold: 4
[    10.887] (II) event5  - Logitech Wireless Mouse: is tagged by udev as: Keyboard Mouse
[    10.888] (II) event5  - Logitech Wireless Mouse: device is a pointer
[    10.888] (II) event5  - Logitech Wireless Mouse: device is a keyboard
[    10.894] (II) config/udev: Adding input device Logitech Wireless Mouse (/dev/input/mouse0)
[    10.894] (II) No input driver specified, ignoring this device.
[    10.894] (II) This device may have been added with another device file.
[    10.897] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event8)
[    10.897] (II) No input driver specified, ignoring this device.
[    10.897] (II) This device may have been added with another device file.
[    10.900] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event9)
[    10.900] (II) No input driver specified, ignoring this device.
[    10.900] (II) This device may have been added with another device file.
[    10.903] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event10)
[    10.903] (II) No input driver specified, ignoring this device.
[    10.903] (II) This device may have been added with another device file.
[    10.906] (II) config/udev: Adding input device AT Raw Set 2 keyboard (/dev/input/event3)
[    10.906] (**) AT Raw Set 2 keyboard: Applying InputClass "libinput keyboard catchall"
[    10.906] (II) Using input driver 'libinput' for 'AT Raw Set 2 keyboard'
[    10.906] (**) AT Raw Set 2 keyboard: always reports core events
[    10.906] (**) Option "Device" "/dev/input/event3"
[    10.910] (II) event3  - AT Raw Set 2 keyboard: is tagged by udev as: Keyboard
[    10.910] (II) event3  - AT Raw Set 2 keyboard: device is a keyboard
[    10.913] (II) event3  - AT Raw Set 2 keyboard: device removed
[    10.928] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input3/event3"
[    10.928] (II) XINPUT: Adding extended input device "AT Raw Set 2 keyboard" (type: KEYBOARD, id 12)
[    10.932] (II) event3  - AT Raw Set 2 keyboard: is tagged by udev as: Keyboard
[    10.932] (II) event3  - AT Raw Set 2 keyboard: device is a keyboard
[    10.937] (II) config/udev: Adding input device PC Speaker (/dev/input/event6)
[    10.937] (II) No input driver specified, ignoring this device.
[    10.937] (II) This device may have been added with another device file.
[    10.992] (**) Logitech Wireless Keyboard PID:4023: Applying InputClass "libinput keyboard catchall"
[    10.992] (II) Using input driver 'libinput' for 'Logitech Wireless Keyboard PID:4023'
[    10.992] (**) Logitech Wireless Keyboard PID:4023: always reports core events
[    10.992] (**) Option "Device" "/dev/input/event4"
[    10.992] (II) libinput: Logitech Wireless Keyboard PID:4023: is a virtual subdevice
[    10.992] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.1/0003:046D:C534.0002/0003:046D:4023.0003/input/input20/event4"
[    10.992] (II) XINPUT: Adding extended input device "Logitech Wireless Keyboard PID:4023" (type: KEYBOARD, id 13)
[    10.993] (**) Logitech Wireless Mouse: Applying InputClass "libinput pointer catchall"
[    10.993] (**) Logitech Wireless Mouse: Applying InputClass "libinput keyboard catchall"
[    10.993] (II) Using input driver 'libinput' for 'Logitech Wireless Mouse'
[    10.993] (**) Logitech Wireless Mouse: always reports core events
[    10.993] (**) Option "Device" "/dev/input/event5"
[    10.993] (II) libinput: Logitech Wireless Mouse: is a virtual subdevice
[    10.993] (II) libinput: Logitech Wireless Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[    10.993] (II) libinput: Logitech Wireless Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[    10.993] (II) libinput: Logitech Wireless Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[    10.993] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.1/0003:046D:C534.0002/0003:046D:4091.0004/input/input22/event5"

I tried i915 and modesetting and the result was the same. I also tried xe driver which finally worked with very low resolution which is not acceptable solution.

Can you please help me with that problem?

Last edited by pmarcinek (2025-12-02 15:46:20)

gromit · 2025-12-02 16:34:33

Can you fix it by downgrading the kernel to the previous kernel? I'm asking as there were updates to other parts of the ecosystem (mkinitcpio, linux-firmware) aswell.

seth · 2025-12-02 21:17:50

[    10.363] (II) IGLX: Loaded and initialized swrast
[    10.363] (II) GLX: Initialized DRISWRAST GL provider for screen 0

Star by getting rid of xf86-video-intel and that config.

Then please post your complete system journal for the boot:

sudo journalctl -b | curl -F 'file=@-' 0x0.st

The error will otherwise not be at the X11 level (at least I assume you're also not getting output on the console?)

pmarcinek · 2025-12-03 10:20:11

gromit wrote:

Can you fix it by downgrading the kernel to the previous kernel? I'm asking as there were updates to other parts of the ecosystem (mkinitcpio, linux-firmware) aswell.

Unfortunately i can't as i need to use the newest OS components - security requirement

pmarcinek · 2025-12-03 10:22:29

seth wrote:

[    10.363] (II) IGLX: Loaded and initialized swrast
[    10.363] (II) GLX: Initialized DRISWRAST GL provider for screen 0
Star by getting rid of xf86-video-intel and that config.
Then please post your complete system journal for the boot:
sudo journalctl -b | curl -F 'file=@-' 0x0.st
The error will otherwise not be at the X11 level (at least I assume you're also not getting output on the console?)

I removed xf86-video-intel and X config. Here is the journalctl output:

http://0x0.st/Ky96.txt

gromit · 2025-12-03 10:22:44

I'm not asking to permanently downgrade, I just want to confirm whether our suspicion that the previous kernel would make it work is actually true.

seth · 2025-12-03 10:34:51

Unfortunately i can't as i need to use the newest OS components - security requirement

Dec 03 10:16:39 archlinux kernel: DMI: GIGABYTE GB-BACE-3160/MZBSWMP-00, BIOS F6 06/13/2018

So if the "newest OS component" had a massive CVE you're not allowed to downgrade to an unaffected version?
Who comes up w/ that kind of retarded shit?
Try the newest LTS kernel …

Dec 03 10:20:58 archlinux sshd-session[552]: Accepted password for root from 192.168.11.247 port 35148 ssh2
Dec 03 10:20:58 archlinux sshd-session[552]: pam_unix(sshd:session): session opened for user root(uid=0) by root(uid=0)
Dec 03 10:20:58 archlinux systemd-logind[352]: New session '2' of user 'root' with class 'user' and type 'tty'.

Also tell that sEcUrItY clown to ban root logins via ssh. FFS.

There're no i915/drm related errors and no complaint about missing crtc, but you#re booting straight into lightdm.
Try to only boot the multi-user.target (2nd link below) and or switch the VT (ctrl+alt+f3)

"i915.nuclear_pageflip=1 intel_idle.max_cstate=1 i915.enable_dc=0 i915.enable_fbc=0 i915.enable_psr=0" are already mitigation efforts?
If you don't get an output on the console either, try to blacklist i915 (you'll be running XGA on the simpledrm device, we just want to see whether the output generates a signal at all)

Does your security expert allow you to boot a different SW stack, eg. a live distro like grml.org so we can rule out broken HW?

Last edited by seth (2025-12-03 10:36:23)

pmarcinek · 2025-12-03 12:18:13

gromit wrote:

I'm not asking to permanently downgrade, I just want to confirm whether our suspicion that the previous kernel would make it work is actually true.

It didn't help. No matter if i use i915 or modesetting i got only cursor flickering in top-left corner. I downgraded to 6.4.6

pmarcinek · 2025-12-03 12:34:43

seth wrote:

Unfortunately i can't as i need to use the newest OS components - security requirement
Dec 03 10:16:39 archlinux kernel: DMI: GIGABYTE GB-BACE-3160/MZBSWMP-00, BIOS F6 06/13/2018
So if the "newest OS component" had a massive CVE you're not allowed to downgrade to an unaffected version?
Who comes up w/ that kind of retarded shit?
Try the newest LTS kernel …
Dec 03 10:20:58 archlinux sshd-session[552]: Accepted password for root from 192.168.11.247 port 35148 ssh2
Dec 03 10:20:58 archlinux sshd-session[552]: pam_unix(sshd:session): session opened for user root(uid=0) by root(uid=0)
Dec 03 10:20:58 archlinux systemd-logind[352]: New session '2' of user 'root' with class 'user' and type 'tty'.
Also tell that sEcUrItY clown to ban root logins via ssh. FFS.
There're no i915/drm related errors and no complaint about missing crtc, but you#re booting straight into lightdm.
Try to only boot the multi-user.target (2nd link below) and or switch the VT (ctrl+alt+f3)
"i915.nuclear_pageflip=1 intel_idle.max_cstate=1 i915.enable_dc=0 i915.enable_fbc=0 i915.enable_psr=0" are already mitigation efforts?
If you don't get an output on the console either, try to blacklist i915 (you'll be running XGA on the simpledrm device, we just want to see whether the output generates a signal at all)
Does your security expert allow you to boot a different SW stack, eg. a live distro like grml.org so we can rule out broken HW?

The security team is checking CVE before image is pushed to production. If there is newer available version, they always push to upgrade.
This specific OS is for testing purposes only - that's why root login is enabled.
The kernel parameters are part of mitigations efforts.
Currently i'm running on:

Linux archlinux 6.12.60-1-lts #1 SMP PREEMPT_DYNAMIC Mon, 01 Dec 2025 13:15:19 +0000 x86_64 GNU/Linux

The effect is exactly the same. If i boot on VGA, then i can see login prompt on tty1. If i boot on HDMI, there is only black screen and "No signal detected" on monitor displayed.
If i blacklist i915 on kernel parameters then i can see login prompt and i can start lightdm and login to graphical environment.
Unfortunately, the monitor is not properly recognized:

[root@archlinux ~]# xrandr -q
Screen 0: minimum 320 x 200, current 1024 x 768, maximum 4096 x 4096
None-1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm
   1024x768      60.00*+

It looks that EDID is missing:

[root@archlinux ~]# cd /sys/class/drm/card0-Unknown-1/
[root@archlinux card0-Unknown-1]# ls -al
total 0
drwxr-xr-x 3 root root    0 Dec  3 12:26 .
drwxr-xr-x 4 root root    0 Dec  3 12:26 ..
-r--r--r-- 1 root root 4096 Dec  3 12:30 connector_id
lrwxrwxrwx 1 root root    0 Dec  3 12:30 device -> ../../card0
-r--r--r-- 1 root root 4096 Dec  3 12:30 dpms
-r--r--r-- 1 root root    0 Dec  3 12:30 edid
-r--r--r-- 1 root root 4096 Dec  3 12:30 enabled
-r--r--r-- 1 root root 4096 Dec  3 12:30 modes
drwxr-xr-x 2 root root    0 Dec  3 12:29 power
-rw-r--r-- 1 root root 4096 Dec  3 12:30 status
lrwxrwxrwx 1 root root    0 Dec  3 12:26 subsystem -> ../../../../../../../class/drm
-rw-r--r-- 1 root root 4096 Dec  3 12:26 uevent
[root@archlinux card0-Unknown-1]# cat edid 
[root@archlinux card0-Unknown-1]#

Then i upgraded to newest kernel (not LTS) and the effect is the same as above - login prompt and lightdm available with low resolution.

Last edited by pmarcinek (2025-12-03 12:44:17)

seth · 2025-12-03 15:19:31

Unfortunately, the monitor is not properly recognized:

That's normal, the simpledrm device only supports some VESA modes (you don't want to use that thing anyway)

If you boot w/o blacklisting i915 but with "video=1024x768@60", https://www.kernel.org/doc/Documentation/fb/modedb.rst to the multi-user.target, do you get some signal on the HDMI monitor?
If you start lightdm and in doubt from the console or via ssh

DISPLAY=:0 xrandr --mode 1024x768 --rate 60

, does the monitor then get a signal?

You should from there also be able to get the EDID and can just cat "edid | curl -F 'file=@-' 0x0.st"
For local inspection or to find it run

for OUT in /sys/class/drm/card*; do echo $OUT; edid-decode $OUT/edid; echo "================="; done

You'll need https://archlinux.org/packages/extra/x86_64/v4l-utils/

pmarcinek · 2025-12-04 10:55:28

seth wrote:

Unfortunately, the monitor is not properly recognized:
That's normal, the simpledrm device only supports some VESA modes (you don't want to use that thing anyway)
If you boot w/o blacklisting i915 but with "video=1024x768@60", https://www.kernel.org/doc/Documentation/fb/modedb.rst to the multi-user.target, do you get some signal on the HDMI monitor?
If you start lightdm and in doubt from the console or via ssh
DISPLAY=:0 xrandr --mode 1024x768 --rate 60
, does the monitor then get a signal?
You should from there also be able to get the EDID and can just cat "edid | curl -F 'file=@-' 0x0.st"
For local inspection or to find it run
for OUT in /sys/class/drm/card*; do echo $OUT; edid-decode $OUT/edid; echo "================="; done
You'll need https://archlinux.org/packages/extra/x86_64/v4l-utils/

If boot w/o blacklisting i915 and video kernel parameter set then i get "No signal" on monitor. I can start lightdm via console and blindly login to graphical session. EDID file seems to be ok:

http://0x0.st/KtZR.bin

If i try running xrandr command with lightdm started it looks that the resolution is changed but there is still no signal on monitor:

[root@archlinux card1-HDMI-A-2]# DISPLAY=:0 xrandr --output HDMI-2 --mode 1024x768 --rate 60
[root@archlinux card1-HDMI-A-2]# xrandr -q
Screen 0: minimum 320 x 200, current 1024 x 768, maximum 16384 x 16384
DP-1 disconnected primary (normal left inverted right x axis y axis)
HDMI-1 disconnected (normal left inverted right x axis y axis)
DP-2 disconnected (normal left inverted right x axis y axis)
HDMI-2 connected 1024x768+0+0 (normal left inverted right x axis y axis) 477mm x 268mm
   1920x1080     60.00 +
   1680x1050     59.88  
   1600x900      60.00  
   1280x1024     75.02    60.02  
   1280x800      59.91  
   1152x864      75.00  
   1280x720      60.00  
   1024x768      75.03    60.00* 
   832x624       74.55  
   800x600       75.00    60.32  
   640x480       75.00    59.94  
   720x400       70.08  
DP-3 disconnected (normal left inverted right x axis y axis)
[root@archlinux card1-HDMI-A-2]# DISPLAY=:0 xrandr --output HDMI-2 --mode 1920x1080 --rate 60
[root@archlinux card1-HDMI-A-2]# xrandr -q
Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 16384 x 16384
DP-1 disconnected primary (normal left inverted right x axis y axis)
HDMI-1 disconnected (normal left inverted right x axis y axis)
DP-2 disconnected (normal left inverted right x axis y axis)
HDMI-2 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 477mm x 268mm
   1920x1080     60.00*+
   1680x1050     59.88  
   1600x900      60.00  
   1280x1024     75.02    60.02  
   1280x800      59.91  
   1152x864      75.00  
   1280x720      60.00  
   1024x768      75.03    60.00  
   832x624       74.55  
   800x600       75.00    60.32  
   640x480       75.00    59.94  
   720x400       70.08  
DP-3 disconnected (normal left inverted right x axis y axis)

Not sure if that helps but i tried to boot with arch netboot image and there is also no signal effect (during netboot image run).
I also tried to install Ubuntu and after rebooting and connecting to HDMI port there is also no signal.
I've done these tests on 3 boards (each one exactly the same model) and 2 monitors (2 different models) - it looks this problem is more general.

seth · 2025-12-04 14:39:14

Since it's coming w/ the i915 module and kernel downgrades and the resolution have no impact I'd suggest to downgrade linux-firmware-intel

pmarcinek · 2025-12-05 08:00:15

seth wrote:

Since it's coming w/ the i915 module and kernel downgrades and the resolution have no impact I'd suggest to downgrade linux-firmware-intel

Tried to downgrade and completely uninstall - still no change

Maybe it's somehow related to xorg-server as the effect is the same with i915 and modesetting driver?

seth · 2025-12-05 09:54:08

Do you get a signal on the console (multi-user.target)?
If not, it cannot be x11.

pmarcinek · 2025-12-10 09:14:36

seth wrote:

Do you get a signal on the console (multi-user.target)?
If not, it cannot be x11.

I do have signal on console when i915 module is blacklisted as a kernel parameter. If i remove blacklisting i915 then i do not get signal on monitor. The rest of configuration remain unchanged.
Xorg log with module blacklisted:

[    39.468] 
X.Org X Server 1.21.1.21
X Protocol Version 11, Revision 0
[    39.468] Current Operating System: Linux archlinux 6.17.9-arch1-1 #1 SMP PREEMPT_DYNAMIC Mon, 24 Nov 2025 15:21:09 +0000 x86_64
[    39.468] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=23985f34-f61d-4573-9e59-b5981ce1e93c rw loglevel=3 module_blacklist=i915 drm.edid_firmware=edid/edid.bin
[    39.468]  
[    39.468] Current version of pixman: 0.46.4
[    39.468]    Before reporting problems, check http://wiki.x.org
        to make sure that you have the latest version.
[    39.468] Markers: (--) probed, (**) from config file, (==) default setting,
        (++) from command line, (!!) notice, (II) informational,
        (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    39.468] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Dec 10 09:09:25 2025
[    39.472] (==) Using config directory: "/etc/X11/xorg.conf.d"
[    39.473] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    39.473] (==) No Layout section.  Using the first Screen section.
[    39.473] (==) No screen section available. Using defaults.
[    39.473] (**) |-->Screen "Default Screen Section" (0)
[    39.473] (**) |   |-->Monitor "<default monitor>"
[    39.475] (==) No device specified for screen "Default Screen Section".
        Using the first device section listed.
[    39.475] (**) |   |-->Device "Intel Graphics"
[    39.475] (==) No monitor specified for screen "Default Screen Section".
        Using a default monitor configuration.
[    39.475] (**) Allowing byte-swapped clients
[    39.475] (==) Automatically adding devices
[    39.475] (==) Automatically enabling devices
[    39.475] (==) Automatically adding GPU devices
[    39.475] (==) Automatically binding GPU devices
[    39.475] (==) Max clients allowed: 256, resource mask: 0x1fffff
[    39.476] (WW) The directory "/usr/share/fonts/misc" does not exist.
[    39.476]    Entry deleted from font path.
[    39.476] (WW) The directory "/usr/share/fonts/TTF" does not exist.
[    39.476]    Entry deleted from font path.
[    39.476] (WW) The directory "/usr/share/fonts/OTF" does not exist.
[    39.476]    Entry deleted from font path.
[    39.476] (WW) The directory "/usr/share/fonts/Type1" does not exist.
[    39.476]    Entry deleted from font path.
[    39.476] (WW) The directory "/usr/share/fonts/100dpi" does not exist.
[    39.476]    Entry deleted from font path.
[    39.476] (WW) The directory "/usr/share/fonts/75dpi" does not exist.
[    39.476]    Entry deleted from font path.
[    39.476] (==) FontPath set to:

[    39.476] (==) ModulePath set to "/usr/lib/xorg/modules"
[    39.476] (II) The server relies on udev to provide the list of input devices.
        If no devices become available, reconfigure udev or disable AutoAddDevices.
[    39.476] (II) Module ABI versions:
[    39.476]    X.Org ANSI C Emulation: 0.4
[    39.476]    X.Org Video Driver: 25.2
[    39.476]    X.Org XInput driver : 24.4
[    39.476]    X.Org Server Extension : 10.0
[    39.477] (++) using VT number 7

[    39.477] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[    39.481] (II) xfree86: Adding drm device (/dev/dri/card0)
[    39.481] (II) Platform probe for /sys/devices/pci0000:00/0000:00:02.0/simple-framebuffer.0/drm/card0
[    39.491] (--) PCI:*(0@0:2:0) 8086:22b1:1458:1000 rev 53, Mem @ 0x80000000/16777216, 0x90000000/268435456, I/O @ 0x0000f000/64, BIOS @ 0x????????/131072
[    39.491] (II) LoadModule: "glx"
[    39.492] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[    39.506] (II) Module glx: vendor="X.Org Foundation"
[    39.506]    compiled for 1.21.1.21, module version = 1.0.0
[    39.506]    ABI class: X.Org Server Extension, version 10.0
[    39.506] (II) LoadModule: "modesetting"
[    39.508] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[    39.513] (II) Module modesetting: vendor="X.Org Foundation"
[    39.513]    compiled for 1.21.1.21, module version = 1.21.1
[    39.513]    Module class: X.Org Video Driver
[    39.513]    ABI class: X.Org Video Driver, version 25.2
[    39.513] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[    39.520] (II) modeset(0): using drv /dev/dri/card0
[    39.521] (II) modeset(0): Creating default Display subsection in Screen section
        "Default Screen Section" for depth/fbbpp 24/32
[    39.521] (==) modeset(0): Depth 24, (==) framebuffer bpp 32
[    39.521] (==) modeset(0): RGB weight 888
[    39.521] (==) modeset(0): Default visual is TrueColor
[    39.521] (II) Loading sub module "glamoregl"
[    39.521] (II) LoadModule: "glamoregl"
[    39.521] (II) Loading /usr/lib/xorg/modules/libglamoregl.so
[    39.537] (II) Module glamoregl: vendor="X.Org Foundation"
[    39.537]    compiled for 1.21.1.21, module version = 1.0.1
[    39.537]    ABI class: X.Org ANSI C Emulation, version 0.4
[    39.740] (II) modeset(0): glamor: Using OpenGL 3.3 context.
[    39.741] (II) modeset(0): glamor X acceleration enabled on softpipe
[    39.741] (II) modeset(0): glamor initialized
[    39.741] (==) modeset(0): VariableRefresh: disabled
[    39.741] (==) modeset(0): AsyncFlipSecondaries: disabled
[    39.741] (II) modeset(0): Output None-1 has no monitor section
[    39.742] (II) modeset(0): EDID for output None-1
[    39.742] (II) modeset(0): Printing probed modes for output None-1
[    39.742] (II) modeset(0): Modeline "1024x768"x60.0   47.19  1024 1024 1024 1024  768 768 768 768 (46.1 kHz eP)
[    39.742] (II) modeset(0): Output None-1 connected
[    39.742] (II) modeset(0): Using exact sizes for initial modes
[    39.742] (II) modeset(0): Output None-1 using initial mode 1024x768 +0+0
[    39.742] (==) modeset(0): Using gamma correction (1.0, 1.0, 1.0)
[    39.742] (==) modeset(0): DPI set to (96, 96)
[    39.742] (II) Loading sub module "fb"
[    39.742] (II) LoadModule: "fb"
[    39.742] (II) Module "fb" already built-in
[    39.867] (==) modeset(0): Backing store enabled
[    39.867] (==) modeset(0): Silken mouse enabled
[    39.870] (II) modeset(0): Initializing kms color map for depth 24, 8 bpc.
[    39.870] (==) modeset(0): DPMS enabled
[    39.870] (WW) modeset(0): Option "DRI" is not used
[    39.870] (WW) modeset(0): Option "CustomEDID" is not used
[    39.870] (WW) modeset(0): Option "IgnoreEDID" is not used
[    39.870] (WW) modeset(0): Option "UseEDID" is not used
[    39.870] (II) modeset(0): [DRI2] Setup complete
[    39.870] (II) modeset(0): [DRI2]   DRI driver: kms_swrast
[    39.870] (II) modeset(0): [DRI2]   VDPAU driver: kms_swrast
[    39.870] (II) Initializing extension Generic Event Extension
[    39.871] (II) Initializing extension SHAPE
[    39.871] (II) Initializing extension MIT-SHM
[    39.871] (II) Initializing extension XInputExtension
[    39.872] (II) Initializing extension XTEST
[    39.872] (II) Initializing extension BIG-REQUESTS
[    39.873] (II) Initializing extension SYNC
[    39.873] (II) Initializing extension XKEYBOARD
[    39.874] (II) Initializing extension XC-MISC
[    39.874] (II) Initializing extension SECURITY
[    39.874] (II) Initializing extension XFIXES
[    39.875] (II) Initializing extension RENDER
[    39.876] (II) Initializing extension RANDR
[    39.877] (II) Initializing extension COMPOSITE
[    39.877] (II) Initializing extension DAMAGE
[    39.877] (II) Initializing extension MIT-SCREEN-SAVER
[    39.878] (II) Initializing extension DOUBLE-BUFFER
[    39.878] (II) Initializing extension RECORD
[    39.878] (II) Initializing extension DPMS
[    39.879] (II) Initializing extension Present
[    39.879] (II) Initializing extension DRI3
[    39.879] (II) Initializing extension X-Resource
[    39.879] (II) Initializing extension XVideo
[    39.880] (II) Initializing extension XVideo-MotionCompensation
[    39.880] (II) Initializing extension GLX
[    39.887] (II) AIGLX: Loaded and initialized kms_swrast
[    39.887] (II) GLX: Initialized DRI2 GL provider for screen 0
[    39.887] (II) Initializing extension XFree86-VidModeExtension
[    39.887] (II) Initializing extension XFree86-DGA
[    39.887] (II) Initializing extension XFree86-DRI
[    39.887] (II) Initializing extension DRI2
[    39.892] (II) modeset(0): Damage tracking initialized
[    39.892] (II) modeset(0): Setting screen physical size to 270 x 203
[    40.341] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[    40.341] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[    40.341] (II) LoadModule: "libinput"
[    40.341] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so
[    40.360] (II) Module libinput: vendor="X.Org Foundation"
[    40.360]    compiled for 1.21.1.13, module version = 1.5.0
[    40.360]    Module class: X.Org XInput Driver
[    40.360]    ABI class: X.Org XInput driver, version 24.4
[    40.360] (II) Using input driver 'libinput' for 'Power Button'
[    40.360] (**) Power Button: always reports core events
[    40.360] (**) Option "Device" "/dev/input/event2"
[    40.394] (II) event2  - Power Button: is tagged by udev as: Keyboard
[    40.394] (II) event2  - Power Button: device is a keyboard
[    40.394] (II) event2  - Power Button: device removed
[    40.406] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2/event2"
[    40.406] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[    40.411] (II) event2  - Power Button: is tagged by udev as: Keyboard
[    40.411] (II) event2  - Power Button: device is a keyboard
[    40.415] (II) config/udev: Adding input device Power Button (/dev/input/event0)
[    40.415] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[    40.415] (II) Using input driver 'libinput' for 'Power Button'
[    40.415] (**) Power Button: always reports core events
[    40.415] (**) Option "Device" "/dev/input/event0"
[    40.419] (II) event0  - Power Button: is tagged by udev as: Keyboard
[    40.419] (II) event0  - Power Button: device is a keyboard
[    40.420] (II) event0  - Power Button: device removed
[    40.428] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0/event0"
[    40.428] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[    40.433] (II) event0  - Power Button: is tagged by udev as: Keyboard
[    40.434] (II) event0  - Power Button: device is a keyboard
[    40.438] (II) config/udev: Adding input device Sleep Button (/dev/input/event1)
[    40.438] (**) Sleep Button: Applying InputClass "libinput keyboard catchall"
[    40.438] (II) Using input driver 'libinput' for 'Sleep Button'
[    40.438] (**) Sleep Button: always reports core events
[    40.438] (**) Option "Device" "/dev/input/event1"
[    40.442] (II) event1  - Sleep Button: is tagged by udev as: Keyboard
[    40.443] (II) event1  - Sleep Button: device is a keyboard
[    40.443] (II) event1  - Sleep Button: device removed
[    40.449] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1/event1"
[    40.449] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 8)
[    40.454] (II) event1  - Sleep Button: is tagged by udev as: Keyboard
[    40.454] (II) event1  - Sleep Button: device is a keyboard
[    40.462] (II) config/udev: Adding input device Logitech Wireless Keyboard PID:4023 (/dev/input/event4)
[    40.462] (**) Logitech Wireless Keyboard PID:4023: Applying InputClass "libinput keyboard catchall"
[    40.463] (II) Using input driver 'libinput' for 'Logitech Wireless Keyboard PID:4023'
[    40.463] (**) Logitech Wireless Keyboard PID:4023: always reports core events
[    40.463] (**) Option "Device" "/dev/input/event4"
[    40.472] (II) event4  - Logitech Wireless Keyboard PID:4023: is tagged by udev as: Keyboard
[    40.473] (II) event4  - Logitech Wireless Keyboard PID:4023: device is a keyboard
[    40.474] (II) event4  - Logitech Wireless Keyboard PID:4023: device removed
[    40.484] (II) libinput: Logitech Wireless Keyboard PID:4023: needs a virtual subdevice
[    40.484] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.1/0003:046D:C534.0002/0003:046D:4023.0003/input/input20/event4"
[    40.484] (II) XINPUT: Adding extended input device "Logitech Wireless Keyboard PID:4023" (type: MOUSE, id 9)
[    40.485] (**) Option "AccelerationScheme" "none"
[    40.485] (**) Logitech Wireless Keyboard PID:4023: (accel) selected scheme none/0
[    40.485] (**) Logitech Wireless Keyboard PID:4023: (accel) acceleration factor: 2.000
[    40.485] (**) Logitech Wireless Keyboard PID:4023: (accel) acceleration threshold: 4
[    40.494] (II) event4  - Logitech Wireless Keyboard PID:4023: is tagged by udev as: Keyboard
[    40.495] (II) event4  - Logitech Wireless Keyboard PID:4023: device is a keyboard
[    40.503] (II) config/udev: Adding input device Logitech Wireless Mouse (/dev/input/event5)
[    40.503] (**) Logitech Wireless Mouse: Applying InputClass "libinput pointer catchall"
[    40.503] (**) Logitech Wireless Mouse: Applying InputClass "libinput keyboard catchall"
[    40.503] (II) Using input driver 'libinput' for 'Logitech Wireless Mouse'
[    40.503] (**) Logitech Wireless Mouse: always reports core events
[    40.503] (**) Option "Device" "/dev/input/event5"
[    40.513] (II) event5  - Logitech Wireless Mouse: is tagged by udev as: Keyboard Mouse
[    40.513] (II) event5  - Logitech Wireless Mouse: device is a pointer
[    40.513] (II) event5  - Logitech Wireless Mouse: device is a keyboard
[    40.514] (II) event5  - Logitech Wireless Mouse: device removed
[    40.520] (II) libinput: Logitech Wireless Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[    40.520] (II) libinput: Logitech Wireless Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[    40.520] (II) libinput: Logitech Wireless Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[    40.520] (II) libinput: Logitech Wireless Mouse: needs a virtual subdevice
[    40.520] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.1/0003:046D:C534.0002/0003:046D:4091.0004/input/input21/event5"
[    40.520] (II) XINPUT: Adding extended input device "Logitech Wireless Mouse" (type: MOUSE, id 10)
[    40.521] (**) Option "AccelerationScheme" "none"
[    40.521] (**) Logitech Wireless Mouse: (accel) selected scheme none/0
[    40.521] (**) Logitech Wireless Mouse: (accel) acceleration factor: 2.000
[    40.521] (**) Logitech Wireless Mouse: (accel) acceleration threshold: 4
[    40.530] (II) event5  - Logitech Wireless Mouse: is tagged by udev as: Keyboard Mouse
[    40.531] (II) event5  - Logitech Wireless Mouse: device is a pointer
[    40.531] (II) event5  - Logitech Wireless Mouse: device is a keyboard
[    40.537] (II) config/udev: Adding input device Logitech Wireless Mouse (/dev/input/mouse0)
[    40.537] (II) No input driver specified, ignoring this device.
[    40.537] (II) This device may have been added with another device file.
[    40.541] (II) config/udev: Adding input device AT Raw Set 2 keyboard (/dev/input/event3)
[    40.541] (**) AT Raw Set 2 keyboard: Applying InputClass "libinput keyboard catchall"
[    40.541] (II) Using input driver 'libinput' for 'AT Raw Set 2 keyboard'
[    40.541] (**) AT Raw Set 2 keyboard: always reports core events
[    40.541] (**) Option "Device" "/dev/input/event3"
[    40.546] (II) event3  - AT Raw Set 2 keyboard: is tagged by udev as: Keyboard
[    40.546] (II) event3  - AT Raw Set 2 keyboard: device is a keyboard
[    40.548] (II) event3  - AT Raw Set 2 keyboard: device removed
[    40.564] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input3/event3"
[    40.564] (II) XINPUT: Adding extended input device "AT Raw Set 2 keyboard" (type: KEYBOARD, id 11)
[    40.569] (II) event3  - AT Raw Set 2 keyboard: is tagged by udev as: Keyboard
[    40.570] (II) event3  - AT Raw Set 2 keyboard: device is a keyboard
[    40.574] (II) config/udev: Adding input device PC Speaker (/dev/input/event6)
[    40.575] (II) No input driver specified, ignoring this device.
[    40.575] (II) This device may have been added with another device file.
[    40.621] (**) Logitech Wireless Keyboard PID:4023: Applying InputClass "libinput keyboard catchall"
[    40.622] (II) Using input driver 'libinput' for 'Logitech Wireless Keyboard PID:4023'
[    40.622] (**) Logitech Wireless Keyboard PID:4023: always reports core events
[    40.622] (**) Option "Device" "/dev/input/event4"
[    40.622] (II) libinput: Logitech Wireless Keyboard PID:4023: is a virtual subdevice
[    40.622] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.1/0003:046D:C534.0002/0003:046D:4023.0003/input/input20/event4"
[    40.622] (II) XINPUT: Adding extended input device "Logitech Wireless Keyboard PID:4023" (type: KEYBOARD, id 12)
[    40.622] (**) Logitech Wireless Mouse: Applying InputClass "libinput pointer catchall"
[    40.622] (**) Logitech Wireless Mouse: Applying InputClass "libinput keyboard catchall"
[    40.622] (II) Using input driver 'libinput' for 'Logitech Wireless Mouse'
[    40.622] (**) Logitech Wireless Mouse: always reports core events
[    40.622] (**) Option "Device" "/dev/input/event5"
[    40.622] (II) libinput: Logitech Wireless Mouse: is a virtual subdevice
[    40.622] (II) libinput: Logitech Wireless Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[    40.623] (II) libinput: Logitech Wireless Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[    40.623] (II) libinput: Logitech Wireless Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[    40.623] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.1/0003:046D:C534.0002/0003:046D:4091.0004/input/input21/event5"
[    40.623] (II) XINPUT: Adding extended input device "Logitech Wireless Mouse" (type: KEYBOARD, id 13)

Xorg log w/o module blacklisted:

[    35.470] 
X.Org X Server 1.21.1.21
X Protocol Version 11, Revision 0
[    35.470] Current Operating System: Linux archlinux 6.17.9-arch1-1 #1 SMP PREEMPT_DYNAMIC Mon, 24 Nov 2025 15:21:09 +0000 x86_64
[    35.470] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=23985f34-f61d-4573-9e59-b5981ce1e93c rw loglevel=3 drm.edid_firmware=edid/edid.bin
[    35.471]  
[    35.471] Current version of pixman: 0.46.4
[    35.471]    Before reporting problems, check http://wiki.x.org
        to make sure that you have the latest version.
[    35.471] Markers: (--) probed, (**) from config file, (==) default setting,
        (++) from command line, (!!) notice, (II) informational,
        (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    35.471] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Dec 10 09:07:28 2025
[    35.475] (==) Using config directory: "/etc/X11/xorg.conf.d"
[    35.475] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    35.476] (==) No Layout section.  Using the first Screen section.
[    35.476] (==) No screen section available. Using defaults.
[    35.476] (**) |-->Screen "Default Screen Section" (0)
[    35.476] (**) |   |-->Monitor "<default monitor>"
[    35.478] (==) No device specified for screen "Default Screen Section".
        Using the first device section listed.
[    35.478] (**) |   |-->Device "Intel Graphics"
[    35.478] (==) No monitor specified for screen "Default Screen Section".
        Using a default monitor configuration.
[    35.478] (**) Allowing byte-swapped clients
[    35.478] (==) Automatically adding devices
[    35.478] (==) Automatically enabling devices
[    35.478] (==) Automatically adding GPU devices
[    35.478] (==) Automatically binding GPU devices
[    35.478] (==) Max clients allowed: 256, resource mask: 0x1fffff
[    35.479] (WW) The directory "/usr/share/fonts/misc" does not exist.
[    35.479]    Entry deleted from font path.
[    35.479] (WW) The directory "/usr/share/fonts/TTF" does not exist.
[    35.479]    Entry deleted from font path.
[    35.479] (WW) The directory "/usr/share/fonts/OTF" does not exist.
[    35.479]    Entry deleted from font path.
[    35.479] (WW) The directory "/usr/share/fonts/Type1" does not exist.
[    35.479]    Entry deleted from font path.
[    35.479] (WW) The directory "/usr/share/fonts/100dpi" does not exist.
[    35.479]    Entry deleted from font path.
[    35.479] (WW) The directory "/usr/share/fonts/75dpi" does not exist.
[    35.479]    Entry deleted from font path.
[    35.479] (==) FontPath set to:

[    35.479] (==) ModulePath set to "/usr/lib/xorg/modules"
[    35.479] (II) The server relies on udev to provide the list of input devices.
        If no devices become available, reconfigure udev or disable AutoAddDevices.
[    35.479] (II) Module ABI versions:
[    35.479]    X.Org ANSI C Emulation: 0.4
[    35.479]    X.Org Video Driver: 25.2
[    35.479]    X.Org XInput driver : 24.4
[    35.479]    X.Org Server Extension : 10.0
[    35.480] (++) using VT number 7

[    35.480] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[    35.487] (II) xfree86: Adding drm device (/dev/dri/card1)
[    35.487] (II) Platform probe for /sys/devices/pci0000:00/0000:00:02.0/drm/card1
[    35.502] (--) PCI:*(0@0:2:0) 8086:22b1:1458:1000 rev 53, Mem @ 0x80000000/16777216, 0x90000000/268435456, I/O @ 0x0000f000/64, BIOS @ 0x????????/131072
[    35.502] (II) LoadModule: "glx"
[    35.503] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[    35.518] (II) Module glx: vendor="X.Org Foundation"
[    35.518]    compiled for 1.21.1.21, module version = 1.0.0
[    35.518]    ABI class: X.Org Server Extension, version 10.0
[    35.518] (II) LoadModule: "modesetting"
[    35.520] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[    35.526] (II) Module modesetting: vendor="X.Org Foundation"
[    35.526]    compiled for 1.21.1.21, module version = 1.21.1
[    35.526]    Module class: X.Org Video Driver
[    35.526]    ABI class: X.Org Video Driver, version 25.2
[    35.526] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[    35.560] (II) modeset(0): using drv /dev/dri/card1
[    35.560] (II) modeset(0): Creating default Display subsection in Screen section
        "Default Screen Section" for depth/fbbpp 24/32
[    35.560] (==) modeset(0): Depth 24, (==) framebuffer bpp 32
[    35.560] (==) modeset(0): RGB weight 888
[    35.560] (==) modeset(0): Default visual is TrueColor
[    35.560] (II) Loading sub module "glamoregl"
[    35.560] (II) LoadModule: "glamoregl"
[    35.561] (II) Loading /usr/lib/xorg/modules/libglamoregl.so
[    35.575] (II) Module glamoregl: vendor="X.Org Foundation"
[    35.575]    compiled for 1.21.1.21, module version = 1.0.1
[    35.575]    ABI class: X.Org ANSI C Emulation, version 0.4
[    35.678] (II) modeset(0): glamor: Using OpenGL 4.6 context.
[    35.678] (II) modeset(0): glamor X acceleration enabled on Mesa DRI Intel(R) HD Graphics 400 (BSW)
[    35.678] (II) modeset(0): glamor initialized
[    35.678] (==) modeset(0): VariableRefresh: disabled
[    35.678] (==) modeset(0): AsyncFlipSecondaries: disabled
[    35.785] (II) modeset(0): Output DP-1 has no monitor section
[    35.787] (II) modeset(0): Output HDMI-1 has no monitor section
[    35.792] (II) modeset(0): Output DP-2 has no monitor section
[    35.795] (II) modeset(0): Output HDMI-2 has no monitor section
[    35.903] (II) modeset(0): Output DP-3 has no monitor section
[    36.031] (II) modeset(0): EDID for output DP-1
[    36.032] (II) modeset(0): EDID for output HDMI-1
[    36.037] (II) modeset(0): EDID for output DP-2
[    36.041] (II) modeset(0): EDID for output HDMI-2
[    36.042] (II) modeset(0): Manufacturer: BNQ  Model: 78cd  Serial#: 21573
[    36.042] (II) modeset(0): Year: 2015  Week: 19
[    36.042] (II) modeset(0): EDID Version: 1.3
[    36.042] (II) modeset(0): Digital Display Input
[    36.042] (II) modeset(0): Max Image Size [cm]: horiz.: 48  vert.: 27
[    36.042] (II) modeset(0): Gamma: 2.20
[    36.042] (II) modeset(0): DPMS capabilities: Off
[    36.042] (II) modeset(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 
[    36.042] (II) modeset(0): Default color space is primary color space
[    36.043] (II) modeset(0): First detailed timing is preferred mode
[    36.043] (II) modeset(0): redX: 0.645 redY: 0.334   greenX: 0.313 greenY: 0.636
[    36.043] (II) modeset(0): blueX: 0.154 blueY: 0.044   whiteX: 0.313 whiteY: 0.329
[    36.043] (II) modeset(0): Supported established timings:
[    36.043] (II) modeset(0): 720x400@70Hz
[    36.043] (II) modeset(0): 640x480@60Hz
[    36.043] (II) modeset(0): 640x480@75Hz
[    36.043] (II) modeset(0): 800x600@60Hz
[    36.043] (II) modeset(0): 800x600@75Hz
[    36.043] (II) modeset(0): 832x624@75Hz
[    36.044] (II) modeset(0): 1024x768@60Hz
[    36.044] (II) modeset(0): 1024x768@75Hz
[    36.044] (II) modeset(0): 1280x1024@75Hz
[    36.044] (II) modeset(0): 1152x864@75Hz
[    36.044] (II) modeset(0): Manufacturer's mask: 0
[    36.044] (II) modeset(0): Supported standard timings:
[    36.044] (II) modeset(0): #0: hsize: 1920  vsize 1080  refresh: 60  vid: 49361
[    36.044] (II) modeset(0): #1: hsize: 1680  vsize 1050  refresh: 60  vid: 179
[    36.044] (II) modeset(0): #2: hsize: 1600  vsize 900  refresh: 60  vid: 49321
[    36.044] (II) modeset(0): #3: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
[    36.044] (II) modeset(0): #4: hsize: 1280  vsize 800  refresh: 60  vid: 129
[    36.044] (II) modeset(0): #5: hsize: 1280  vsize 720  refresh: 60  vid: 49281
[    36.046] (II) modeset(0): Supported detailed timing:
[    36.046] (II) modeset(0): clock: 148.5 MHz   Image Size:  477 x 268 mm
[    36.046] (II) modeset(0): h_active: 1920  h_sync: 2008  h_sync_end 2052 h_blank_end 2200 h_border: 0
[    36.046] (II) modeset(0): v_active: 1080  v_sync: 1084  v_sync_end 1089 v_blanking: 1125 v_border: 0
[    36.046] (II) modeset(0): Serial No: 45F01851019
[    36.046] (II) modeset(0): Ranges: V min: 50 V max: 76 Hz, H min: 30 H max: 83 kHz, PixClock max 175 MHz
[    36.046] (II) modeset(0): Monitor name: BenQ GW2255
[    36.046] (II) modeset(0): EDID (in hex):
[    36.046] (II) modeset(0):   00ffffffffffff0009d1cd7845540000
[    36.047] (II) modeset(0):   1319010380301b782e2795a55550a227
[    36.047] (II) modeset(0):   0b5054a56b80d1c0b300a9c081808100
[    36.047] (II) modeset(0):   81c001010101023a801871382d40582c
[    36.047] (II) modeset(0):   4500dd0c1100001e000000ff00343546
[    36.047] (II) modeset(0):   30313835313031390a20000000fd0032
[    36.047] (II) modeset(0):   4c1e5311000a202020202020000000fc
[    36.047] (II) modeset(0):   0042656e51204757323235350a200010
[    36.048] (II) modeset(0): Printing probed modes for output HDMI-2
[    36.049] (II) modeset(0): Modeline "1920x1080"x60.0  148.50  1920 2008 2052 2200  1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[    36.049] (II) modeset(0): Modeline "1680x1050"x59.9  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz e)
[    36.049] (II) modeset(0): Modeline "1600x900"x60.0  108.00  1600 1624 1704 1800  900 901 904 1000 +hsync +vsync (60.0 kHz e)
[    36.049] (II) modeset(0): Modeline "1280x1024"x75.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[    36.049] (II) modeset(0): Modeline "1280x1024"x60.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[    36.049] (II) modeset(0): Modeline "1280x800"x59.9   71.00  1280 1328 1360 1440  800 803 809 823 +hsync -vsync (49.3 kHz e)
[    36.049] (II) modeset(0): Modeline "1152x864"x75.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz e)
[    36.050] (II) modeset(0): Modeline "1280x720"x60.0   74.25  1280 1390 1430 1650  720 725 730 750 +hsync +vsync (45.0 kHz e)
[    36.050] (II) modeset(0): Modeline "1024x768"x75.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz e)
[    36.050] (II) modeset(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz e)
[    36.050] (II) modeset(0): Modeline "832x624"x74.6   57.28  832 864 928 1152  624 625 628 667 -hsync -vsync (49.7 kHz e)
[    36.050] (II) modeset(0): Modeline "800x600"x75.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz e)
[    36.050] (II) modeset(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz e)
[    36.050] (II) modeset(0): Modeline "640x480"x75.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz e)
[    36.050] (II) modeset(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz e)
[    36.051] (II) modeset(0): Modeline "720x400"x70.1   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz e)
[    36.170] (II) modeset(0): EDID for output DP-3
[    36.170] (II) modeset(0): Output DP-1 disconnected
[    36.170] (II) modeset(0): Output HDMI-1 disconnected
[    36.170] (II) modeset(0): Output DP-2 disconnected
[    36.170] (II) modeset(0): Output HDMI-2 connected
[    36.170] (II) modeset(0): Output DP-3 disconnected
[    36.170] (II) modeset(0): Using exact sizes for initial modes
[    36.170] (II) modeset(0): Output HDMI-2 using initial mode 1920x1080 +0+0
[    36.171] (==) modeset(0): Using gamma correction (1.0, 1.0, 1.0)
[    36.171] (==) modeset(0): DPI set to (96, 96)
[    36.171] (II) Loading sub module "fb"
[    36.171] (II) LoadModule: "fb"
[    36.171] (II) Module "fb" already built-in
[    36.473] (==) modeset(0): Backing store enabled
[    36.474] (==) modeset(0): Silken mouse enabled
[    36.577] (II) modeset(0): Initializing kms color map for depth 24, 8 bpc.
[    36.578] (==) modeset(0): DPMS enabled
[    36.578] (WW) modeset(0): Option "DRI" is not used
[    36.578] (WW) modeset(0): Option "CustomEDID" is not used
[    36.578] (WW) modeset(0): Option "IgnoreEDID" is not used
[    36.578] (WW) modeset(0): Option "UseEDID" is not used
[    36.578] (II) modeset(0): [DRI2] Setup complete
[    36.578] (II) modeset(0): [DRI2]   DRI driver: i965
[    36.578] (II) modeset(0): [DRI2]   VDPAU driver: va_gl
[    36.578] (II) Initializing extension Generic Event Extension
[    36.579] (II) Initializing extension SHAPE
[    36.580] (II) Initializing extension MIT-SHM
[    36.580] (II) Initializing extension XInputExtension
[    36.581] (II) Initializing extension XTEST
[    36.582] (II) Initializing extension BIG-REQUESTS
[    36.582] (II) Initializing extension SYNC
[    36.583] (II) Initializing extension XKEYBOARD
[    36.585] (II) Initializing extension XC-MISC
[    36.586] (II) Initializing extension SECURITY
[    36.587] (II) Initializing extension XFIXES
[    36.587] (II) Initializing extension RENDER
[    36.588] (II) Initializing extension RANDR
[    36.589] (II) Initializing extension COMPOSITE
[    36.590] (II) Initializing extension DAMAGE
[    36.590] (II) Initializing extension MIT-SCREEN-SAVER
[    36.591] (II) Initializing extension DOUBLE-BUFFER
[    36.592] (II) Initializing extension RECORD
[    36.592] (II) Initializing extension DPMS
[    36.593] (II) Initializing extension Present
[    36.593] (II) Initializing extension DRI3
[    36.594] (II) Initializing extension X-Resource
[    36.594] (II) Initializing extension XVideo
[    36.595] (II) Initializing extension XVideo-MotionCompensation
[    36.595] (II) Initializing extension GLX
[    36.604] (II) AIGLX: Loaded and initialized i965
[    36.604] (II) GLX: Initialized DRI2 GL provider for screen 0
[    36.604] (II) Initializing extension XFree86-VidModeExtension
[    36.605] (II) Initializing extension XFree86-DGA
[    36.606] (II) Initializing extension XFree86-DRI
[    36.606] (II) Initializing extension DRI2
[    36.609] (II) modeset(0): Damage tracking initialized
[    36.609] (II) modeset(0): Setting screen physical size to 508 x 285
[    36.935] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[    36.935] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[    36.935] (II) LoadModule: "libinput"
[    36.935] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so
[    36.949] (II) Module libinput: vendor="X.Org Foundation"
[    36.949]    compiled for 1.21.1.13, module version = 1.5.0
[    36.949]    Module class: X.Org XInput Driver
[    36.949]    ABI class: X.Org XInput driver, version 24.4
[    36.949] (II) Using input driver 'libinput' for 'Power Button'
[    36.949] (**) Power Button: always reports core events
[    36.949] (**) Option "Device" "/dev/input/event2"
[    36.966] (II) event2  - Power Button: is tagged by udev as: Keyboard
[    36.966] (II) event2  - Power Button: device is a keyboard
[    36.966] (II) event2  - Power Button: device removed
[    36.975] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2/event2"
[    36.975] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[    36.979] (II) event2  - Power Button: is tagged by udev as: Keyboard
[    36.979] (II) event2  - Power Button: device is a keyboard
[    36.983] (II) config/udev: Adding input device Video Bus (/dev/input/event6)
[    36.983] (**) Video Bus: Applying InputClass "libinput keyboard catchall"
[    36.983] (II) Using input driver 'libinput' for 'Video Bus'
[    36.983] (**) Video Bus: always reports core events
[    36.983] (**) Option "Device" "/dev/input/event6"
[    36.987] (II) event6  - Video Bus: is tagged by udev as: Keyboard
[    36.987] (II) event6  - Video Bus: device is a keyboard
[    36.987] (II) event6  - Video Bus: device removed
[    36.998] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input22/event6"
[    36.998] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[    37.003] (II) event6  - Video Bus: is tagged by udev as: Keyboard
[    37.003] (II) event6  - Video Bus: device is a keyboard
[    37.006] (II) config/udev: Adding input device Power Button (/dev/input/event0)
[    37.006] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[    37.007] (II) Using input driver 'libinput' for 'Power Button'
[    37.007] (**) Power Button: always reports core events
[    37.007] (**) Option "Device" "/dev/input/event0"
[    37.010] (II) event0  - Power Button: is tagged by udev as: Keyboard
[    37.011] (II) event0  - Power Button: device is a keyboard
[    37.011] (II) event0  - Power Button: device removed
[    37.015] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0/event0"
[    37.015] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[    37.020] (II) event0  - Power Button: is tagged by udev as: Keyboard
[    37.020] (II) event0  - Power Button: device is a keyboard
[    37.023] (II) config/udev: Adding input device Sleep Button (/dev/input/event1)
[    37.024] (**) Sleep Button: Applying InputClass "libinput keyboard catchall"
[    37.024] (II) Using input driver 'libinput' for 'Sleep Button'
[    37.024] (**) Sleep Button: always reports core events
[    37.024] (**) Option "Device" "/dev/input/event1"
[    37.028] (II) event1  - Sleep Button: is tagged by udev as: Keyboard
[    37.028] (II) event1  - Sleep Button: device is a keyboard
[    37.028] (II) event1  - Sleep Button: device removed
[    37.032] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1/event1"
[    37.032] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 9)
[    37.037] (II) event1  - Sleep Button: is tagged by udev as: Keyboard
[    37.037] (II) event1  - Sleep Button: device is a keyboard
[    37.046] (II) config/udev: Adding input device Logitech Wireless Keyboard PID:4023 (/dev/input/event4)
[    37.046] (**) Logitech Wireless Keyboard PID:4023: Applying InputClass "libinput keyboard catchall"
[    37.046] (II) Using input driver 'libinput' for 'Logitech Wireless Keyboard PID:4023'
[    37.046] (**) Logitech Wireless Keyboard PID:4023: always reports core events
[    37.046] (**) Option "Device" "/dev/input/event4"
[    37.054] (II) event4  - Logitech Wireless Keyboard PID:4023: is tagged by udev as: Keyboard
[    37.054] (II) event4  - Logitech Wireless Keyboard PID:4023: device is a keyboard
[    37.055] (II) event4  - Logitech Wireless Keyboard PID:4023: device removed
[    37.068] (II) libinput: Logitech Wireless Keyboard PID:4023: needs a virtual subdevice
[    37.068] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.1/0003:046D:C534.0002/0003:046D:4023.0003/input/input20/event4"
[    37.068] (II) XINPUT: Adding extended input device "Logitech Wireless Keyboard PID:4023" (type: MOUSE, id 10)
[    37.068] (**) Option "AccelerationScheme" "none"
[    37.068] (**) Logitech Wireless Keyboard PID:4023: (accel) selected scheme none/0
[    37.068] (**) Logitech Wireless Keyboard PID:4023: (accel) acceleration factor: 2.000
[    37.068] (**) Logitech Wireless Keyboard PID:4023: (accel) acceleration threshold: 4
[    37.076] (II) event4  - Logitech Wireless Keyboard PID:4023: is tagged by udev as: Keyboard
[    37.077] (II) event4  - Logitech Wireless Keyboard PID:4023: device is a keyboard
[    37.083] (II) config/udev: Adding input device Logitech Wireless Mouse (/dev/input/event5)
[    37.083] (**) Logitech Wireless Mouse: Applying InputClass "libinput pointer catchall"
[    37.083] (**) Logitech Wireless Mouse: Applying InputClass "libinput keyboard catchall"
[    37.083] (II) Using input driver 'libinput' for 'Logitech Wireless Mouse'
[    37.083] (**) Logitech Wireless Mouse: always reports core events
[    37.083] (**) Option "Device" "/dev/input/event5"
[    37.090] (II) event5  - Logitech Wireless Mouse: is tagged by udev as: Keyboard Mouse
[    37.092] (II) event5  - Logitech Wireless Mouse: device is a pointer
[    37.092] (II) event5  - Logitech Wireless Mouse: device is a keyboard
[    37.092] (II) event5  - Logitech Wireless Mouse: device removed
[    37.102] (II) libinput: Logitech Wireless Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[    37.102] (II) libinput: Logitech Wireless Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[    37.102] (II) libinput: Logitech Wireless Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[    37.102] (II) libinput: Logitech Wireless Mouse: needs a virtual subdevice
[    37.102] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.1/0003:046D:C534.0002/0003:046D:4091.0004/input/input21/event5"
[    37.103] (II) XINPUT: Adding extended input device "Logitech Wireless Mouse" (type: MOUSE, id 11)
[    37.103] (**) Option "AccelerationScheme" "none"
[    37.103] (**) Logitech Wireless Mouse: (accel) selected scheme none/0
[    37.104] (**) Logitech Wireless Mouse: (accel) acceleration factor: 2.000
[    37.104] (**) Logitech Wireless Mouse: (accel) acceleration threshold: 4
[    37.111] (II) event5  - Logitech Wireless Mouse: is tagged by udev as: Keyboard Mouse
[    37.112] (II) event5  - Logitech Wireless Mouse: device is a pointer
[    37.112] (II) event5  - Logitech Wireless Mouse: device is a keyboard
[    37.118] (II) config/udev: Adding input device Logitech Wireless Mouse (/dev/input/mouse0)
[    37.118] (II) No input driver specified, ignoring this device.
[    37.118] (II) This device may have been added with another device file.
[    37.120] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event8)
[    37.120] (II) No input driver specified, ignoring this device.
[    37.121] (II) This device may have been added with another device file.
[    37.123] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event9)
[    37.123] (II) No input driver specified, ignoring this device.
[    37.123] (II) This device may have been added with another device file.
[    37.126] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event10)
[    37.126] (II) No input driver specified, ignoring this device.
[    37.126] (II) This device may have been added with another device file.
[    37.129] (II) config/udev: Adding input device AT Raw Set 2 keyboard (/dev/input/event3)
[    37.129] (**) AT Raw Set 2 keyboard: Applying InputClass "libinput keyboard catchall"
[    37.129] (II) Using input driver 'libinput' for 'AT Raw Set 2 keyboard'
[    37.129] (**) AT Raw Set 2 keyboard: always reports core events
[    37.129] (**) Option "Device" "/dev/input/event3"
[    37.133] (II) event3  - AT Raw Set 2 keyboard: is tagged by udev as: Keyboard
[    37.133] (II) event3  - AT Raw Set 2 keyboard: device is a keyboard
[    37.135] (II) event3  - AT Raw Set 2 keyboard: device removed
[    37.144] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input3/event3"
[    37.145] (II) XINPUT: Adding extended input device "AT Raw Set 2 keyboard" (type: KEYBOARD, id 12)
[    37.149] (II) event3  - AT Raw Set 2 keyboard: is tagged by udev as: Keyboard
[    37.149] (II) event3  - AT Raw Set 2 keyboard: device is a keyboard
[    37.154] (II) config/udev: Adding input device PC Speaker (/dev/input/event7)
[    37.154] (II) No input driver specified, ignoring this device.
[    37.154] (II) This device may have been added with another device file.
[    37.197] (**) Logitech Wireless Keyboard PID:4023: Applying InputClass "libinput keyboard catchall"
[    37.197] (II) Using input driver 'libinput' for 'Logitech Wireless Keyboard PID:4023'
[    37.197] (**) Logitech Wireless Keyboard PID:4023: always reports core events
[    37.197] (**) Option "Device" "/dev/input/event4"
[    37.197] (II) libinput: Logitech Wireless Keyboard PID:4023: is a virtual subdevice
[    37.197] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.1/0003:046D:C534.0002/0003:046D:4023.0003/input/input20/event4"
[    37.197] (II) XINPUT: Adding extended input device "Logitech Wireless Keyboard PID:4023" (type: KEYBOARD, id 13)
[    37.198] (**) Logitech Wireless Mouse: Applying InputClass "libinput pointer catchall"
[    37.198] (**) Logitech Wireless Mouse: Applying InputClass "libinput keyboard catchall"
[    37.198] (II) Using input driver 'libinput' for 'Logitech Wireless Mouse'
[    37.198] (**) Logitech Wireless Mouse: always reports core events
[    37.198] (**) Option "Device" "/dev/input/event5"
[    37.198] (II) libinput: Logitech Wireless Mouse: is a virtual subdevice
[    37.198] (II) libinput: Logitech Wireless Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[    37.198] (II) libinput: Logitech Wireless Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[    37.198] (II) libinput: Logitech Wireless Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[    37.198] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.1/0003:046D:C534.0002/0003:046D:4091.0004/input/input21/event5"
[    37.198] (II) XINPUT: Adding extended input device "Logitech Wireless Mouse" (type: KEYBOARD, id 14)
[    37.760] (II) modeset(0): EDID vendor "BNQ", prod id 30925
[    37.761] (II) modeset(0): Using EDID range info for horizontal sync
[    37.761] (II) modeset(0): Using EDID range info for vertical refresh
[    37.761] (II) modeset(0): Printing DDC gathered Modelines:
[    37.761] (II) modeset(0): Modeline "1920x1080"x0.0  148.50  1920 2008 2052 2200  1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[    37.761] (II) modeset(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz e)
[    37.761] (II) modeset(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz e)
[    37.761] (II) modeset(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz e)
[    37.761] (II) modeset(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz e)
[    37.762] (II) modeset(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[    37.762] (II) modeset(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz e)
[    37.762] (II) modeset(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz e)
[    37.762] (II) modeset(0): Modeline "832x624"x0.0   57.28  832 864 928 1152  624 625 628 667 -hsync -vsync (49.7 kHz e)
[    37.762] (II) modeset(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz e)
[    37.762] (II) modeset(0): Modeline "1152x864"x0.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz e)
[    37.762] (II) modeset(0): Modeline "1680x1050"x0.0  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz e)
[    37.762] (II) modeset(0): Modeline "1600x900"x60.0  119.00  1600 1696 1864 2128  900 901 904 932 -hsync +vsync (55.9 kHz e)
[    37.762] (II) modeset(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[    37.763] (II) modeset(0): Modeline "1280x800"x0.0   71.00  1280 1328 1360 1440  800 803 809 823 +hsync -vsync (49.3 kHz e)
[    37.763] (II) modeset(0): Modeline "1280x720"x60.0   74.48  1280 1336 1472 1664  720 721 724 746 -hsync +vsync (44.8 kHz e)

Any suggestions?

pmarcinek · 2025-12-10 14:07:36

I found some old OS image with HDMI working correctly. It was running on kernel 6.4.X. I started updating packages: xorg-server, glibc, mesa and rebooted - everything worked fine. Then i updated kernel and rebooted - as a result i can see "No signal" on the monitor. Kernel bug?

seth · 2025-12-10 17:45:40

If i remove blacklisting i915 then i do not get signal on monitor.

ie.

Kernel bug

6.4 is of course ancient, to what version did you update?
You can get older kernels from https://archive.archlinux.org/packages/l/linux/
Make sure to also install the LTS kernel, if you're downgrading the kernel too much it might no longer boot because the toolchain used to compile it is too old.

pmarcinek · 2025-12-12 10:02:22

I updated to the newest which is 6.17.9. I also tried newest linux-lts earlier but no luck - still no signal on monitor. Should i try older lts?

seth · 2025-12-12 16:05:29

Should i try older lts?

Yup - it would be very useful to know between which two kernels this was introduced.
Whether you're trying the LTS or the main ones doesn't matter but don't test this linearly - 6.4 is good, 6.12 is bad, so try some 6.8 kernel next.

Arch Linux

#1 2025-12-02 15:43:21

HDMI no signal after kernel update

#2 2025-12-02 16:34:33

Re: HDMI no signal after kernel update

#3 2025-12-02 21:17:50

Re: HDMI no signal after kernel update

#4 2025-12-03 10:20:11

Re: HDMI no signal after kernel update

#5 2025-12-03 10:22:29

Re: HDMI no signal after kernel update

#6 2025-12-03 10:22:44

Re: HDMI no signal after kernel update

#7 2025-12-03 10:34:51

Re: HDMI no signal after kernel update

#8 2025-12-03 12:18:13

Re: HDMI no signal after kernel update

#9 2025-12-03 12:34:43

Re: HDMI no signal after kernel update

#10 2025-12-03 15:19:31

Re: HDMI no signal after kernel update

#11 2025-12-04 10:55:28

Re: HDMI no signal after kernel update

#12 2025-12-04 14:39:14

Re: HDMI no signal after kernel update

#13 2025-12-05 08:00:15

Re: HDMI no signal after kernel update

#14 2025-12-05 09:54:08

Re: HDMI no signal after kernel update

#15 2025-12-10 09:14:36

Re: HDMI no signal after kernel update

#16 2025-12-10 14:07:36

Re: HDMI no signal after kernel update

#17 2025-12-10 17:45:40

Re: HDMI no signal after kernel update

#18 2025-12-12 10:02:22

Re: HDMI no signal after kernel update

#19 2025-12-12 16:05:29

Re: HDMI no signal after kernel update

Board footer