Arch Linux

gol2008

Member

Registered: 2006-08-10

Posts: 2

SOS!!! burn cd fail...

system: archlinux  update to latest

message:

wodim: No write mode specified.
wodim: Asuming -tao mode.
wodim: Future versions of wodim may have different drive dependent defaults.
scsidev: '1,0,0'
scsibus: 1 target: 0 lun: 0
Linux sg driver version: 3.5.34
Wodim version: 1.1.2
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 0 = CD-DA
atapi: 1
Device type    : Removable CD-ROM
Version        : 5
Response Format: 2
Capabilities   : 
Vendor_info    : 'HL-DT-ST'
Identification : 'DVDRAM GSA-H42N '
Revision       : 'RL00'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x0009 (CD-R)
Profile: 0x0012 (DVD-RAM) 
Profile: 0x0011 (DVD-R sequential recording) 
Profile: 0x0015 (DVD-R/DL sequential recording) 
Profile: 0x0016 (DVD-R/DL layer jump recording) 
Profile: 0x0014 (DVD-RW sequential recording) 
Profile: 0x0013 (DVD-RW restricted overwrite) 
Profile: 0x001A (DVD+RW) 
Profile: 0x001B (DVD+R) 
Profile: 0x002B (DVD+R/DL) 
Profile: 0x0010 (DVD-ROM) 
Profile: 0x0009 (CD-R) (current)
Profile: 0x000A (CD-RW) 
Profile: 0x0008 (CD-ROM) 
Profile: 0x0002 (Removable disk) 
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE 
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1053696 = 1029 KB
Drive DMA Speed: 13138 kB/s 74x CD 9x DVD
FIFO size      : 4194304 = 4096 KB
sub type: Medium Type A, high Beta category (A+) (3)
  ATIP start of lead in:  -11634 (97:26/66)
  ATIP start of lead out: 359846 (79:59/71)
Disk type:    Short strategy type (Phthalocyanine or similar)
Manuf. index: 3
Manufacturer: CMC Magnetics Corporation
Blocks total: 359846 Blocks current: 359846 Blocks remaining: 27200
Starting to write CD/DVD at speed  16.0 in real TAO mode for single session.
Last chance to quit, starting real write in 5 seconds.Speed set to 2822 KB/s
   4 seconds.   3 seconds.   2 seconds.   1 seconds.   0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Starting new track at sector: 0
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB:  2A 00 00 00 00 87 00 00 1B 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 2A 30 02 80 21 02 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x21 Qual 0x02 (invalid address for write) Fru 0x0
Sense flags: Blk 0 (not valid) 
resid: 63504
cmd finished after 0.002s timeout 40s
wodim: The current problem looks like a buffer underrun.
wodim: It looks like 'driveropts=burnfree' does not work for this drive.
wodim: Please report.able DMA and check your HW/OS set up.

wodim: Make sure that you are root, en
write track data: error after 317520 bytes
Writing  time:   16.614s
Average write speed 267.8x.
Fixating...
Fixating time:   18.603s

mucknert

Member

From: Berlin // Germany

Registered: 2006-06-27

Posts: 510

Re: SOS!!! burn cd fail...

Do that as root or add the user you want to burn with to the group 'optical'.

---

Todays mistakes are tomorrows catastrophes.

gol2008

Member

Registered: 2006-08-10

Posts: 2

Re: SOS!!! burn cd fail...

I'm root, But the same problem!

iphitus

Forum Fellow

From: Melbourne, Australia

Registered: 2004-10-09

Posts: 4,927

Re: SOS!!! burn cd fail...

Enable dma with hdparm -d1 /dev/cdrom
or whatever your device's device name is.

James

paulr

Member

Registered: 2007-03-23

Posts: 52

Re: SOS!!! burn cd fail...

Possibly this problem which I've found on Ubuntu Feisty Fawn as well (tried it out, still prefer Arch) ; the new IDE quasi-SCSI drivers which seem to have appeared in 2.6.20 do not always play well with burning.

Might be worth trying reverting to the old IDE system (see post) see if it works there. For me, went from 90% coasters to perfect.

http://bbs.archlinux.org/viewtopic.php?id=31679