You are not logged in.
- Topics: Active | Unanswered
#1 2007-07-17 08:28:09
- Davigetto
- Member
- From: In your mind
- Registered: 2007-05-10
- Posts: 266
How Can I configure network manager correctly?
Well, in debian, when I started the gnome session, immediately I was asked for a password to connect my default wireless connection. It is the correct way I want.
In arch, the process is: First, the network manager connects to localhost (I don't know why...), and I have to select manually my wireless net to connect to it, and put my password.
Is there anyway to make this process as it was in debian? So, when I start gnome session, be asked for password and connect immediately.
My rc.conf:
#
# /etc/rc.conf - Main Configuration for Arch Linux
##
# -----------------------------------------------------------------------
# LOCALIZATION
# -----------------------------------------------------------------------
#
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
#
LOCALE="es_ES.UTF-8"
HARDWARECLOCK="localtime"
TIMEZONE="Europe/Madrid"
KEYMAP="es"
CONSOLEFONT="lat1-16"
CONSOLEMAP=
USECOLOR="yes"#
# -----------------------------------------------------------------------
# HARDWARE
# -----------------------------------------------------------------------
#
# Scan hardware and load required modules at bootup
MOD_AUTOLOAD="yes"
# Module Blacklist - modules in this list will never be loaded by udev
MOD_BLACKLIST=()
#
# Modules to load at boot-up (in this order)
# - prefix a module with a ! to blacklist it
#
MODULES=(ipw3945 8139too mii cpufreq_powersave cpufreq_userspace
freq_table acpi_cpufreq asus_acpi sn9c102)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"#
# -----------------------------------------------------------------------
# NETWORKING
# -----------------------------------------------------------------------
#
HOSTNAME="samantha"
#
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available
# interfaces.
#
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
#
# Note: to use DHCP, set your interface to be "dhcp" (eth0="dhcp")
#
lo="lo 127.0.0.1"
eth0="dhcp"
eth2="dhcp"
INTERFACES=(lo !eth0 !eth2)
#
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
#
gateway="default gw 192.168.1.1"
ROUTES=(!gateway)
#
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
#
# Network profiles are found in /etc/network-profiles
#
#NET_PROFILES=(main)#
# -----------------------------------------------------------------------
# DAEMONS
# -----------------------------------------------------------------------
#
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
#
DAEMONS=(syslog-ng crond hal hwd cpudyn @alsa xinetd vmware ipw3945d
laptop-mode dhcdbd networkmanager !network netfs gdm)# End of file
Greetings
Only deaths can see the end of battles.
Blog: http://djmartinez.co.cc -> The life of a Computer Engineer
Offline