Problems with my network card..

Crooksey · 2007-07-13 11:30:59

I have just installed arch on my new desktop computer, everything seems fine after a base install,

Now, the command $ ifconfig, displays lo and eth0, recognizes the hardware name and all sorts, but for some reason dhcpcd always fails to run (times out) on eth0,.

The device works fine under fedora (temporary solution), but I was wondering how I would go about making my network card work under arch.

lspci

01.03.0Ethernet controller: Marvell Tech ltd. 88E8001 Gigabit Ethernet controller (rev 14)

Any ideas?

Lone_Wolf · 2007-07-13 13:14:25

please post your /etc/rc.conf

Crooksey · 2007-07-26 15:44:13

I thought I could get by using Gentoo, but no.... so Im here to get this sorted...

#rc.conf
#
# /etc/rc.conf - Main Configuration for Arch Linux
#

#
# -----------------------------------------------------------------------
# LOCALIZATION
# -----------------------------------------------------------------------
#
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
#
LOCALE="en_GB.utf8"
HARDWARECLOCK="localtime"
TIMEZONE="Canada/Pacific"
KEYMAP="uk"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"

#
# -----------------------------------------------------------------------
# HARDWARE
# -----------------------------------------------------------------------
#
# Scan hardware and load required modules at bootup
MOD_AUTOLOAD="yes"
# Module Blacklist - modules in this list will never be loaded by udev
MOD_BLACKLIST=()
#
# Modules to load at boot-up (in this order)
#   - prefix a module with a ! to blacklist it
#
MODULES=(sk98lin skge slhc snd-mixer-oss snd-pcm-oss snd-seq-oss snd-seq-device snd-seq-midi-event snd-seq snd-hwdep snd-page-alloc snd-pcm snd-rawmidi snd-timer snd snd-hda-intel soundcore snd-usb-audio snd-usb-lib)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"

#
# -----------------------------------------------------------------------
# NETWORKING
# -----------------------------------------------------------------------
#
HOSTNAME="dreamy"
#
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available
# interfaces.
#
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
#   - prefix an entry in INTERFACES with a ! to disable it
#   - no hyphens in your interface names - Bash doesn't like it
#
# Note: to use DHCP, set your interface to be "dhcp" (eth0="dhcp")
#
lo="lo 127.0.0.1"
eth0="dhcp"
INTERFACES=(lo eth0)
#
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
#   - prefix an entry in ROUTES with a ! to disable it
#
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
#
# Enable these network profiles at boot-up.  These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
#   - set to 'menu' to present a menu during boot-up (dialog package required)
#   - prefix an entry with a ! to disable it
#
# Network profiles are found in /etc/network-profiles
#
#NET_PROFILES=(main)

#
# -----------------------------------------------------------------------
# DAEMONS
# -----------------------------------------------------------------------
#
# Daemons to start at boot-up (in this order)
#   - prefix a daemon with a ! to disable it
#   - prefix a daemon with a @ to start it up in the background
#
DAEMONS=(syslog-ng network netfs crond hal alsa gdm)


# End of file

#lscpi
00:00.0 Host bridge: Intel Corporation 82946GZ/PL/GL Memory Controller Hub (rev 02)
00:01.0 PCI bridge: Intel Corporation 82946GZ/PL/GL PCI Express Root Port (rev 02)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01)
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controller IDE (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
01:00.0 VGA compatible controller: nVidia Corporation Unknown device 0400 (rev a1)
02:03.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 14)

#dmesg | grep Ethernet
eth0: Marvell Yukon 88E8001 Gigabit Ethernet Controller

Crooksey · 2007-07-26 19:13:31

I needed to backlist the sk98lin module, thanks #archlinux and slubman!

Last edited by Crooksey (2007-07-26 19:15:46)

Arch Linux

#1 2007-07-13 11:30:59

Problems with my network card..

#2 2007-07-13 13:14:25

Re: Problems with my network card..

#3 2007-07-26 15:44:13

Re: Problems with my network card..

#4 2007-07-26 19:13:31

Re: Problems with my network card..

Board footer