[UNSOLVED] CD Recording

meinhimmel · 2007-07-12 19:54:05

I'm having issues with CD Recording.

This is all being run as root by the way.

"xcdroast -d 100" returns an infinite loop of

Trying to map to old ATA syntax.This workaround will disappear in the near future. Fix your configuration.Unable to open this SCSI ID.

"cdrecord -scanbus" returns

scsibus1:
1,0,0 100) 'CDWRITER' 'IDE5224 ' 'S027' Removable CD-ROM
1,1,0 101) *
1,2,0 102) *
1,3,0 103) *
1,4,0 104) *
1,5,0 105) *
1,6,0 106) *

I also tried graveman and that froze as well when scanning cd drives.

I can mount cds fine so I know that its setup correctly at least inside of the computer.

Any ideas?

Last edited by meinhimmel (2007-07-15 20:15:25)

Manny500 · 2007-07-12 20:14:27

Perhaps you are using wrong ATA drivers? What kernel are you running and what is the output of dmesg?

meinhimmel · 2007-07-12 20:36:00

"dmesg"

Linux version 2.6.21-ARCH (root@workstation64) (gcc version 4.2.1 20070704 (prerelease)) #1 SMP PREEMPT Sat Jul 7 09:57:11 UTC 2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
copy_e820_map() start: 00000000000e4000 size: 0000000000008000 end: 00000000000ec000 type: 2
copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end: 0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000001fef0000 end: 000000001fff0000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000001fff0000 size: 0000000000008000 end: 000000001fff8000 type: 3
copy_e820_map() start: 000000001fff8000 size: 0000000000008000 end: 0000000020000000 type: 4
copy_e820_map() start: 00000000fec00000 size: 0000000000001000 end: 00000000fec01000 type: 2
copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end: 00000000fee01000 type: 2
copy_e820_map() start: 00000000fff80000 size: 0000000000080000 end: 0000000100000000 type: 2
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 00000000000ec000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data)
BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
found SMP MP-table at 000fb7e0
Entering add_active_range(0, 0, 131056) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 131056
HighMem 131056 -> 131056
early_node_map[1] active PFN ranges
0: 0 -> 131056
On node 0 totalpages: 131056
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 991 pages used for memmap
Normal zone: 125969 pages, LIFO batch:31
HighMem zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000FA820, 0014 (r0 AMI )
ACPI: RSDT 1FFF0000, 002C (r1 AMIINT VIA_K7 10 MSFT 97)
ACPI: FACP 1FFF0030, 0081 (r1 AMIINT VIA_K7 11 MSFT 97)
ACPI: DSDT 1FFF0120, 3546 (r1 VIA VIA_K7 1000 MSFT 100000D)
ACPI: FACS 1FFF8000, 0040
ACPI: APIC 1FFF00C0, 0054 (r1 AMIINT VIA_K7 9 MSFT 97)
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Built 1 zonelists. Total pages: 130033
Kernel command line: root=/dev/sda3 ro vga=775
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 1666.549 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 513832k/524224k available (2315k kernel code, 9788k reserved, 761k data, 268k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfff83000 - 0xfffff000 ( 496 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB)
.init : 0xc0407000 - 0xc044a000 ( 268 kB)
.data : 0xc0342e4d - 0xc040128c ( 761 kB)
.text : 0xc0100000 - 0xc0342e4d (2315 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3336.86 BogoMIPS (lpj=6673735)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000
CPU: CLK_CTL MSR was 6003d22f. Reprogramming to 2003d22f
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000420 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 11k freed
Early unpacking initramfs... done
ACPI: Core revision 20070126
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
CPU0: AMD Athlon(tm) XP 2000+ stepping 01
Total of 1 processors activated (3336.86 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfdab1, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 9 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
Time: tsc clocksource has been installed.
pnp: 00:04: iomem range 0xfee00000-0xfee00fff could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: dde00000-dfefffff
PREFETCH window: bdd00000-ddcfffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 6, 262144 bytes)
TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 1572k freed
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Bypassing VIA 8237 APIC De-Assert Message
vesafb: framebuffer at 0xc0000000, mapped to 0xe0880000, using 2560k, total 262144k
vesafb: mode is 1280x1024x8, linelength=1280, pages=1
vesafb: protected mode interface info at c000:e2e0
vesafb: pmi: set display start = c00ce316, set palette = c00ce380
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: scrolling: redraw
vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
Console: switching to colour frame buffer device 160x64
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
Switched to high resolution mode on CPU 0
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
input: Macintosh mouse button emulation as /class/input/input0
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Freeing unused kernel memory: 268k freed
libata version 2.20 loaded.
pata_via 0000:00:0f.1: version 0.2.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 16
ata1: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001fc00 irq 14
ata2: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001fc08 irq 15
scsi0 : pata_via
ata1.00: ATA-7: Maxtor 6Y060L0, YAR41VW0, max UDMA/133
ata1.00: 120103200 sectors, multi 16: LBA
ata1.00: configured for UDMA/133
scsi1 : pata_via
ATA: abnormal status 0x7F on port 0x00010177
ATA: abnormal status 0x7F on port 0x00010177
ata2.00: ATAPI, max UDMA/33
ata2.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA Maxtor 6Y060L0 YAR4 PQ: 0 ANSI: 5
scsi 1:0:0:0: CD-ROM CDWRITER IDE5224 S027 PQ: 0 ANSI: 5
sata_via 0000:00:0f.0: version 2.1
ACPI: PCI Interrupt 0000:00:0f.0[b] -> GSI 20 (level, low) -> IRQ 16
sata_via 0000:00:0f.0: routed to hard irq line 10
ata3: SATA max UDMA/133 cmd 0x0001ec00 ctl 0x0001e802 bmdma 0x0001dc00 irq 16
ata4: SATA max UDMA/133 cmd 0x0001e400 ctl 0x0001e002 bmdma 0x0001dc08 irq 16
scsi2 : sata_via
ata3: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
ATA: abnormal status 0x7F on port 0x0001ec07
scsi3 : sata_via
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ATA: abnormal status 0x7F on port 0x0001e407
ATA: abnormal status 0x7F on port 0x0001e407
ata4.00: ATA-7: SAMSUNG SP1614C, SW100-34, max UDMA7
ata4.00: 312581808 sectors, multi 16: LBA48
ata4.00: configured for UDMA/133
scsi 3:0:0:0: Direct-Access ATA SAMSUNG SP1614C SW10 PQ: 0 ANSI: 5
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 17
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 17, io base 0x0000b800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
SCSI device sda: 120103200 512-byte hdwr sectors (61493 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 120103200 512-byte hdwr sectors (61493 MB)
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 17
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 17, io base 0x0000bc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
sr0: scsi3-mmc drive: 40x/52x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
ACPI: PCI Interrupt 0000:00:10.2[b] -> GSI 21 (level, low) -> IRQ 17
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 17, io base 0x0000c000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
sdb: Write Protect is off
usb 1-1: new low speed USB device using uhci_hcd and address 2
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 3:0:0:0: Attached scsi disk sdb
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 17
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.4: irq 17, io mem 0xdfffbc00
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:00:10.3[b] -> GSI 21 (level, low) -> IRQ 17
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 17, io base 0x0000c400
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 1-1: device not accepting address 2, error -71
ReiserFS: sda3: found reiserfs format "3.6" with standard journal
ReiserFS: sda3: using ordered data mode
ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda3: checking transaction log (sda3)
ReiserFS: sda3: Using r5 hash to sort names
usb 1-1: new low speed USB device using uhci_hcd and address 4
usb 1-1: configuration #1 chosen from 1 choice
Linux Tulip driver version 1.1.14 (May 11, 2002)
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 18
eth0: Lite-On PNIC-II rev 37 at Port 0xd400, 00:A0:CC:35:A3:DD, IRQ 18.
via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 19
eth1: VIA Rhine II at 0x1b000, 00:50:2c:a3:d7:e4, IRQ 19.
eth1: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
usbcore: registered new interface driver hiddev
input: Logitech USB Receiver as /class/input/input1
input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:10.0-1
input: Logitech USB Receiver as /class/input/input2
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:10.0-1
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 20
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:11.5 to 64
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input5
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU1] (supports 16 throttling states)
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
sd 3:0:0:0: Attached scsi generic sg2 type 0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: AGP aperture is 256M @ 0xe0000000
input: PC Speaker as /class/input/input6
PPP generic driver version 2.4.2
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
ReiserFS: sda2: found reiserfs format "3.6" with standard journal
ReiserFS: sda2: using ordered data mode
ReiserFS: sda2: journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda2: checking transaction log (sda2)
ReiserFS: sda2: Using r5 hash to sort names
Adding 2931820k swap on /dev/sda1. Priority:-1 extents:1 across:2931820k
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
eth0: no IPv6 routers present
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 22
NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.11 Wed Jun 13 18:21:22 PDT 2007
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
fuse init (API version 7.8)
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
usb 4-3: new high speed USB device using ehci_hcd and address 3
usb 4-3: configuration #1 chosen from 1 choice
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Initializing USB Mass Storage driver...
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
scsi 4:0:0:0: Direct-Access WDC WD50 00AAKS-00TMA0 PQ: 0 ANSI: 2
SCSI device sdc: 976773168 512-byte hdwr sectors (500108 MB)
sdc: Write Protect is off
sdc: Mode Sense: 38 00 00 00
sdc: assuming drive cache: write through
SCSI device sdc: 976773168 512-byte hdwr sectors (500108 MB)
sdc: Write Protect is off
sdc: Mode Sense: 38 00 00 00
sdc: assuming drive cache: write through
sdc: sdc1
sd 4:0:0:0: Attached scsi disk sdc
sd 4:0:0:0: Attached scsi generic sg3 type 0
usb-storage: device scan complete
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sdc.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev loop1.
usb 4-3: USB disconnect, address 3
cdrom: sr0: mrw address space DMA selected
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
cdrom: sr0: mrw address space DMA selected
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A

The most current kernel that comes stock with 2007.5 version of Arch Linux.

meinhimmel · 2007-07-15 20:14:55

just bumping this back up to the top. i still haven't solved this and i have no idea what's wrong..?

Moparx · 2007-07-15 20:22:26

I was having this issue as well with two completely different drives.
I ended up fixing it through my favorite burning software (bashburn) by changing the configuration from /dev/sr0 to /dev/scd0

btartsa · 2007-07-15 22:14:01

K3B is the only burning app I've had any degree of success with.

Ruckus · 2007-08-24 22:20:14

Moparx wrote:

I was having this issue as well with two completely different drives.
I ended up fixing it through my favorite burning software (bashburn) by changing the configuration from /dev/sr0 to /dev/scd0

I am having this same problem, but your sollution did not help unfortunately.

Arch Linux

#1 2007-07-12 19:54:05

[UNSOLVED] CD Recording

#2 2007-07-12 20:14:27

Re: [UNSOLVED] CD Recording

#3 2007-07-12 20:36:00

Re: [UNSOLVED] CD Recording

#4 2007-07-15 20:14:55

Re: [UNSOLVED] CD Recording

#5 2007-07-15 20:22:26

Re: [UNSOLVED] CD Recording

#6 2007-07-15 22:14:01

Re: [UNSOLVED] CD Recording

#7 2007-08-24 22:20:14

Re: [UNSOLVED] CD Recording

Board footer