[Solved] No harddisk on my laptop?

mariourk · 2007-10-10 12:22:18

I'm trying to install Archlinux on my noteboot (Mynote C750)
Booting from the cdrom goes fine. But when I try to partition my harddrive, it gives an error.
So, I decided to partition the harddrive manually. To my surprise, Archlinux says there is no harddrive present.

The IDE-controller is a SiS 5513. Funny though, because the cdromdrive works perfectly. And it is connected
to the same controller.

I hope someone can help me out here?

Last edited by mariourk (2007-10-11 11:41:27)

luca · 2007-10-10 13:01:45

Hi mariourk,
post the output of dmesg command

cu3edweb · 2007-10-10 13:43:41

Did you try the

ide-legacy

boot option?

mariourk · 2007-10-10 14:59:45

Here is de output of dmesg:

Linux version 2.6.22-ARCH (root@T-POWA-LX) (gcc version 4.2.1) #1 SMP PREEMPT Wed Sep 26 20:57:40 CEST 2007
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000000affb000 (usable)
 BIOS-e820: 000000000affb000 - 000000000afff000 (ACPI data)
 BIOS-e820: 000000000afff000 - 000000000b000000 (ACPI NVS)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
175MB LOWMEM available.
Entering add_active_range(0, 0, 45051) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->    45051
  HighMem     45051 ->    45051
early_node_map[1] active PFN ranges
    0:        0 ->    45051
On node 0 totalpages: 45051
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 319 pages used for memmap
  Normal zone: 40636 pages, LIFO batch:7
  HighMem zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000F58F0, 0014 (r0 ASUS  )
ACPI: RSDT 0AFFB000, 002C (r1 ASUS   Generic  30303031 MSFT 31313031)
ACPI: FACP 0AFFB080, 0074 (r1 ASUS   Generic  30303031 MSFT 31313031)
ACPI: DSDT 0AFFB100, 301C (r1   ASUS A1B          1000 MSFT  100000B)
ACPI: FACS 0AFFF000, 0040
ACPI: BOOT 0AFFB040, 0028 (r1 ASUS   Generic  30303031 MSFT 31313031)
ACPI: PM-Timer IO Port: 0xe408
Allocating PCI resources starting at 10000000 (gap: 0b000000:f4ff0000)
Built 1 zonelists.  Total pages: 44700
Kernel command line: initrd=initrd.img rootdelay=5 BOOT_IMAGE=vmlinuz 
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (0116c000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 4096 bytes)
Detected 598.193 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 145792k/180204k available (2391k kernel code, 33884k reserved, 780k data, 304k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff82000 - 0xfffff000   ( 500 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xcb800000 - 0xff7fe000   ( 831 MB)
    lowmem  : 0xc0000000 - 0xcaffb000   ( 175 MB)
      .init : 0xc041f000 - 0xc046b000   ( 304 kB)
      .data : 0xc0355f5f - 0xc04191bc   ( 780 kB)
      .text : 0xc0100000 - 0xc0355f5f   (2391 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1197.06 BogoMIPS (lpj=1995301)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 11k freed
Early unpacking initramfs... done
ACPI: Core revision 20070126
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
ACPI: setting ELCR to 0200 (from 0020)
CPU0: Intel Celeron (Coppermine) stepping 06
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf09f0, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 11)
ACPI: Power Resource [PFAN] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: BIOS reporting unknown device 00:50
PCI: Device 0000:00:0a.1 not found by BIOS
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
ACPI: RTC can wake from S4
pnp: 00:00: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:00: iomem range 0xf0000-0xfffff could not be reserved
pnp: 00:00: iomem range 0x100000-0xaffffff could not be reserved
pnp: 00:00: iomem range 0xffee0000-0xffefffff has been reserved
pnp: 00:02: ioport range 0xe400-0xe47f has been reserved
pnp: 00:02: ioport range 0xe480-0xe4ff has been reserved
pnp: 00:02: ioport range 0x296-0x296 has been reserved
pnp: 00:02: ioport range 0x600-0x61f has been reserved
pnp: 00:02: ioport range 0x4d0-0x4d1 has been reserved
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:02.0
  IO window: 9000-9fff
  MEM window: cd800000-cdffffff
  PREFETCH window: d8000000-e7efffff
PCI: Bus 2, cardbus bridge: 0000:00:0a.0
  IO window: 00001000-000010ff
  IO window: 00001400-000014ff
  PREFETCH window: 10000000-13ffffff
  MEM window: 14000000-17ffffff
PCI: Bus 6, cardbus bridge: 0000:00:0a.1
  IO window: 00001800-000018ff
  IO window: 00001c00-00001cff
  PREFETCH window: 18000000-1bffffff
  MEM window: 1c000000-1fffffff
PCI: Setting latency timer of device 0000:00:02.0 to 64
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.1[b] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 98304 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
checking if image is initramfs...<6>Switched to high resolution mode on CPU 0
 it is
Freeing initrd memory: 28426k freed
Simple Boot Flag at 0x3a set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:01:00.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:01.6[b] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt for device 0000:00:01.6 disabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: module loaded
input: Macintosh mouse button emulation as /class/input/input0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Freeing unused kernel memory: 304k freed
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input4
ACPI: Sleep Button (CM) [SLPB]
input: Lid Switch as /class/input/input5
ACPI: Lid Switch [LID]
ACPI: Transitioning device [FAN] to D3
ACPI: Transitioning device [FAN] to D3
ACPI: Fan [FAN] (off)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THRM] (63 C)
rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k
ACPI: PCI Interrupt 0000:00:01.6[b] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt 0000:00:01.4[b] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
Marking TSC unstable due to: possible TSC halt in C2.
Time: acpi_pm clocksource has been installed.
gameport: Trident 4DWave is pci0000:00:01.4/gameport0, speed 2130kHz
libata version 2.21 loaded.
pata_sis 0000:00:00.1: version 0.5.1
ACPI: Unable to derive IRQ for device 0000:00:00.1
ACPI: PCI Interrupt 0000:00:00.1[A]: no GSI - using IRQ 14
PCI: setting IRQ 14 as level-triggered
irq 14: nobody cared (try booting with the "irqpoll" option)
 [<c0157494>] __report_bad_irq+0x24/0x80
 [<c0157751>] note_interrupt+0x261/0x2a0
 [<c01569c0>] handle_IRQ_event+0x30/0x60
 [<c0158311>] handle_level_irq+0xa1/0x110
 [<c0106f4b>] do_IRQ+0x3b/0x70
 [<c0106f50>] do_IRQ+0x40/0x70
 [<c0104da3>] common_interrupt+0x23/0x28
 [<c0130a2a>] __do_softirq+0x5a/0x110
 [<c0130b35>] do_softirq+0x55/0x60
 [<c0130db9>] irq_exit+0x79/0x90
 [<c0106f50>] do_IRQ+0x40/0x70
 [<c0104da3>] common_interrupt+0x23/0x28
 [<c0354f2d>] _spin_unlock_irqrestore+0xd/0x30
 [<c01571ae>] setup_irq+0xce/0x1a0
 [<cb905480>] ata_interrupt+0x0/0x220 [libata]
 [<c0157321>] request_irq+0xa1/0xc0
 [<cb9093b0>] ata_pci_init_one+0x450/0x5e0 [libata]
 [<cb905480>] ata_interrupt+0x0/0x220 [libata]
 [<cb905480>] ata_interrupt+0x0/0x220 [libata]
 [<cb836857>] sis_init_one+0x167/0x510 [pata_sis]
 [<c0240775>] pci_match_device+0xa5/0xc0
 [<c0240806>] pci_device_probe+0x56/0x80
 [<c0298cc8>] driver_probe_device+0x88/0x190
 [<c035191f>] klist_next+0x5f/0xc0
 [<c0298f20>] __driver_attach+0x80/0x90
 [<c02980ca>] bus_for_each_dev+0x3a/0x60
 [<c0298b36>] driver_attach+0x16/0x20
 [<c0298ea0>] __driver_attach+0x0/0x90
 [<c029845a>] bus_add_driver+0x8a/0x1b0
 [<c02409c0>] __pci_register_driver+0x60/0xa0
 [<c014dcc6>] sys_init_module+0x126/0x1990
 [<c016baf3>] vma_link+0xb3/0x100
 [<c016c8dd>] do_mmap_pgoff+0x52d/0x7a0
 [<c010433e>] sysenter_past_esp+0x6b/0xa1
 =======================
handlers:
[<cb905480>] (ata_interrupt+0x0/0x220 [libata])
Disabling IRQ #14
scsi0 : pata_sis
scsi1 : pata_sis
ata1: PATA max UDMA/66 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001b400 irq 14
ata2: PATA max UDMA/66 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001b408 irq 15
ata1.00: qc timeout (cmd 0x27)
ata1.00: ata_hpa_resize 1: hpa sectors (0) is smaller than sectors (39070080)
ata1.00: ATA-6: HTS541020G9AT00, MB1OA60A, max UDMA/100
ata1.00: 39070080 sectors, multi 16: LBA48 
ata1.00: limited to UDMA/33 due to 40-wire cable
ata1.00: failed to set xfermode (err_mask=0x40)
ata1: failed to recover some devices, retrying in 5 secs
ata1.00: qc timeout (cmd 0x27)
ata1.00: ata_hpa_resize 1: hpa sectors (0) is smaller than sectors (39070080)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: limiting speed to UDMA/33:PIO3
ata1: failed to recover some devices, retrying in 5 secs
ata1.00: qc timeout (cmd 0x27)
ata1.00: ata_hpa_resize 1: hpa sectors (0) is smaller than sectors (39070080)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: disabled
ata2.00: ATAPI: CD-224E, 1.5A, max MWDMA2
ata2.00: configured for PIO4
scsi 1:0:0:0: CD-ROM            TEAC     CD-224E          1.5A PQ: 0 ANSI: 5
PPP generic driver version 2.4.2
sis900.c: v1.08.10 Apr. 2 2006
ACPI: PCI Interrupt 0000:00:01.1[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
0000:00:01.1: SiS 900 Internal MII PHY transceiver found at address 1.
0000:00:01.1: Using transceiver found at address 1 as default
eth0: SiS 900 PCI Fast Ethernet at 0xb000, IRQ 5, 00:e0:18:1b:34:4a.
Yenta: CardBus bridge found at 0000:00:0a.0 [1043:1504]
Yenta: ISA IRQ mask 0x0498, PCI irq 11
Socket status: 30000006
Yenta: CardBus bridge found at 0000:00:0a.1 [1043:1504]
Yenta: ISA IRQ mask 0x0498, PCI irq 5
Socket status: 30000006
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:01.2[D] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
ohci_hcd 0000:00:01.2: OHCI Host Controller
ohci_hcd 0000:00:01.2: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:01.2: irq 5, io mem 0xcf000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:00:01.3[D] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
ohci_hcd 0000:00:01.3: OHCI Host Controller
ohci_hcd 0000:00:01.3: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:01.3: irq 5, io mem 0xce800000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 2-1: new low speed USB device using ohci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
cs: IO port probe 0x100-0x3af: excluding 0x378-0x37f
cs: IO port probe 0x3e0-0x4ff: excluding 0x480-0x48f
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0x100-0x3af: excluding 0x378-0x37f
cs: IO port probe 0x3e0-0x4ff: excluding 0x480-0x48f
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
sr0: scsi3-mmc drive: 24x/24x xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
usbcore: registered new interface driver hiddev
input: Logitech USB-PS/2 Optical Mouse as /class/input/input6
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:01.3-1
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
md: linear personality registered for level -1
md: multipath personality registered for level -4
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid5: automatically using best checksumming function: pIII_sse
   pIII_sse  :  1167.600 MB/sec
raid5: using function: pIII_sse (1167.600 MB/sec)
raid6: int32x1    180 MB/s
raid6: int32x2    200 MB/s
raid6: int32x4    164 MB/s
raid6: int32x8    151 MB/s
raid6: mmxx1      465 MB/s
raid6: mmxx2      594 MB/s
raid6: sse1x1     266 MB/s
raid6: sse1x2     427 MB/s
raid6: using algorithm sse1x2 (427 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com

I will try the ide-legacy boot-option too.

luca · 2007-10-10 15:06:56

Try booting with the "irqpoll" option

mariourk · 2007-10-10 15:23:10

de boot option ide-legacy did the trick. Arch reconised my harddrive and I was able to partition it. Right now it is installing the packages. I'm looking forward to put my first Arch Linux installation to the test. It's looking very promising

Last edited by mariourk (2007-10-11 07:19:31)

mariourk · 2007-10-11 07:18:46

ArchLinux is now installed on my laptop. I've got Xorg and Gnome running without much trouble.

I was looking for a good alternative for Gentoo. I really liked Gentoo (actually, I still do) but I got tired of it, because maintaining a Gentoo system has become a living hell. So, I installed Ubuntu on my desktop and decided it was nice. I also wanted to install it on my laptop, but I couldn't get it running. I suppose the problem was also related to my IDE-controller, because Grub could't find the partition Ubuntu was installed on. Since I couldn't get it right, I searched on for another alternative. PCLinuxOS also refused to install. And than I stumbled on ArchLinux. At first I also had, once again, the same IDE-controller problem. But this time I got some good help and managed to fix it.

I'm allready feeling home in my new ArchLinux environment. It's doesn't differ that much from Gentoo and it is pretty straightforward. The documentation seems also to be ok. Everthing I wanted to know was in he wiki. I think ArchLinux is going to stay on my laptop.

Thanks everybody!

cu3edweb · 2007-10-11 16:39:44

mariourk wrote:

ArchLinux is now installed on my laptop. I've got Xorg and Gnome running without much trouble.
I was looking for a good alternative for Gentoo. I really liked Gentoo (actually, I still do) but I got tired of it, because maintaining a Gentoo system has become a living hell. So, I installed Ubuntu on my desktop and decided it was nice. I also wanted to install it on my laptop, but I couldn't get it running. I suppose the problem was also related to my IDE-controller, because Grub could't find the partition Ubuntu was installed on. Since I couldn't get it right, I searched on for another alternative. PCLinuxOS also refused to install. And than I stumbled on ArchLinux. At first I also had, once again, the same IDE-controller problem. But this time I got some good help and managed to fix it.
I'm allready feeling home in my new ArchLinux environment. It's doesn't differ that much from Gentoo and it is pretty straightforward. The documentation seems also to be ok. Everthing I wanted to know was in he wiki. I think ArchLinux is going to stay on my laptop.
Thanks everybody!

Thats weird that ubuntu and pclinuxos wouldn't install. I had to use ide-legacy to install arch but ubuntu and pclinuxos install fine with no boot options.

Glad you got it working

Last edited by cu3edweb (2007-10-11 16:40:02)

Arch Linux

#1 2007-10-10 12:22:18

[Solved] No harddisk on my laptop?

#2 2007-10-10 13:01:45

Re: [Solved] No harddisk on my laptop?

#3 2007-10-10 13:43:41

Re: [Solved] No harddisk on my laptop?

#4 2007-10-10 14:59:45

Re: [Solved] No harddisk on my laptop?

#5 2007-10-10 15:06:56

Re: [Solved] No harddisk on my laptop?

#6 2007-10-10 15:23:10

Re: [Solved] No harddisk on my laptop?

#7 2007-10-11 07:18:46

Re: [Solved] No harddisk on my laptop?

#8 2007-10-11 16:39:44

Re: [Solved] No harddisk on my laptop?

Board footer