You are not logged in.

#1 2008-04-05 14:10:06

Kai
Member
From: Germany
Registered: 2006-12-11
Posts: 27

kernel Panic while booting

Hi folks,

I have a very strange issue here;

I have updated my kernel from 2.6.24.3-6 to 2.6.24.4-1.
The next boot went well but starting with the second one the kernel does not want to boot;
The error message says nothing:

Kinit: Init not found.

I've tried to downgrade to the old kernel but this did not help either.

Btw: My fallback image does work.

My mkinitcpio.conf

# vim:set ft=sh
# MODULES
# The following modules are loaded before any boot hooks are
# run.  Advanced users may wish to specify all system modules
# in this array.  For instance:
#     MODULES="piix ide_disk reiserfs"
MODULES="reiserfs"

# BINARIES
# This setting includes, into the CPIO image, and additional
# binaries a given user may wish.  This is run first, so may
# be used to override the actual binaries used in a given hook.
# (Existing files are NOT overwritten is already added)
# BINARIES are dependancy parsed, so you may safely ignore libraries
BINARIES=""

# FILES
# This setting is similar to BINARIES above, however, files are added
# as-is and are not parsed in anyway.  This is useful for config files.
# Some users may wish to include modprobe.conf for custom module options,
# like so:
#    FILES="/etc/modprobe.conf"
FILES=""

# HOOKS
# This is the most important setting in this file.  The HOOKS control the
# modules and scripts added to the image, and what happens at boot time.
# Order is important, and it is recommended that you do not change the
# order in which HOOKS are added.  Run 'mkinitcpio -H <hook name>' for
# help on a given hook.
# 'base' is _required_ unless you know precisely what you are doing.
# 'udev' is _required_ in order to automatically load modules
# 'modload' may be used in place of 'udev', but is not recommended
# 'filesystems' is _required_ unless you specify your fs modules in MODULES
# Examples:
#    This setup specifies all modules in the MODULES setting above.
#    No raid, lvm2, or encrypted root is needed.
#    HOOKS="base"
#
#    This setup will autodetect all modules for your system and should
#    work as a sane default
#    HOOKS="base udev autodetect pata scsi sata filesystems"
#
#    This is identical to the above, except the old ide subsystem is
#    used for IDE devices instead of the new pata subsystem.
#    HOOKS="base udev autodetect ide scsi sata filesystems"
#
#    This setup will generate a 'full' image which supports most systems.
#    No autodetection is done.
#    HOOKS="base udev pata scsi sata usb filesystems"
#
#    This setup assembles an pata raid array with an encrypted root FS.
#    Note: See 'mkinitcpio -H raid' for more information on raid devices.
#    HOOKS="base udev pata raid encrypt filesystems"
#
#    This setup loads an lvm2 volume group on a usb device.
#    HOOKS="base udev usb lvm2 filesystems"
HOOKS="base udev autodetect pata sata filesystems"

My root partition is /dev/sda3 with reiserfs.

Any ideas?!

Offline

#2 2008-04-05 22:03:24

Kai
Member
From: Germany
Registered: 2006-12-11
Posts: 27

Re: kernel Panic while booting

I have no idea why but adding

MODULES="piix ide_disk reiserfs"

to the mkinitcpio.conf helped...

Offline

Board footer

Powered by FluxBB