You are not logged in.
- Topics: Active | Unanswered
#26 2008-11-18 16:36:14
- Dieter@be
- Forum Fellow
- From: Belgium
- Registered: 2006-11-05
- Posts: 2,001
- Website
Re: "No Space Left on Device" (df -h shows 45GB free!!)
It looks like your hard disk is broken, do this:
* dd if=/dev/<disk> of=/<backup file here> # to save/backup as much of the blockdevice as you can, because any read/write/recovery attempt can make it worse
* try to recover your data from the backup (mount -o loop, recovery tools etc)
* get rid of the disk, get a new one
< Daenyth> and he works prolifically
4 8 15 16 23 42
Offline
#27 2008-11-18 17:41:28
- Sophotect
- Member
- From: Hyperbolic excess
- Registered: 2007-03-25
- Posts: 30
Re: "No Space Left on Device" (df -h shows 45GB free!!)
What made me say that probably your ESata-Cabling is faulty was this, right out of your DMESG.
------
ata3: exception Emask 0x50 SAct 0x0 SErr 0x90800 action 0xe frozen
ata3: irq_stat 0x00400000, PHY RDY changed
ata3: SError: { HostInt PHYRdyChg 10B8B }
ata3: hard resetting link
ata3: SATA link down (SStatus 0 SControl 300)
ata3: hard resetting link
ata3: SATA link down (SStatus 0 SControl 300)
ata3: hard resetting link
ata3: SATA link down (SStatus 0 SControl 300)
ata3.00: disabled
ata3: EH complete
ata3.00: detaching (SCSI 2:0:0:0)
sd 2:0:0:0: [sdc] Synchronizing SCSI cache
sd 2:0:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
sd 2:0:0:0: [sdc] Stopping disk
sd 2:0:0:0: [sdc] START_STOP FAILED
sd 2:0:0:0: [sdc] Result: hostbyte=0x04 driverbyte=0x00
ata3: exception Emask 0x50 SAct 0x0 SErr 0x40d0802 action 0xe frozen
ata3: irq_stat 0x00000040, connection status changed
ata3: SError: { RecovComm HostInt PHYRdyChg CommWake 10B8B DevExch }
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: qc timeout (cmd 0xec)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata3: hard resetting link
ata3: link is slow to respond, please be patient (ready=0)
ata3: COMRESET failed (errno=-16)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: qc timeout (cmd 0xec)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: qc timeout (cmd 0xec)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata3: hard resetting link
ata3: link is slow to respond, please be patient (ready=0)
ata3: COMRESET failed (errno=-16)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x7 t4
ata3: SError: { HostInt 10B8B }
ata3: hard resetting link
ata3: link is slow to respond, please be patient (ready=0)
ata3: COMRESET failed (errno=-16)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: qc timeout (cmd 0xec)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: qc timeout (cmd 0xec)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: qc timeout (cmd 0xec)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x7 t3
ata3: SError: { HostInt 10B8B }
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: qc timeout (cmd 0xec)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: qc timeout (cmd 0xec)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3: exception Emask 0x50 SAct 0x0 SErr 0x80800 action 0x7 t2
ata3: irq_stat 0x0c000000, interface fatal error
ata3: SError: { HostInt 10B8B }
ata3: hard resetting link
ata3: link is slow to respond, please be patient (ready=0)
ata3: COMRESET failed (errno=-16)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: qc timeout (cmd 0xec)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata3: hard resetting link
ata3: link is slow to respond, please be patient (ready=0)
ata3: COMRESET failed (errno=-16)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3: exception Emask 0x50 SAct 0x0 SErr 0x80800 action 0x7 t1
ata3: irq_stat 0x08000002, interface fatal error
ata3: SError: { HostInt 10B8B }
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: qc timeout (cmd 0xec)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: qc timeout (cmd 0xec)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: qc timeout (cmd 0xec)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3: EH pending after 5 tries, giving up
ata3: EH complete
ata3: exception Emask 0x50 SAct 0x0 SErr 0x90800 action 0xe frozen
ata3: irq_stat 0x00400000, PHY RDY changed
ata3: SError: { HostInt PHYRdyChg 10B8B }
ata3: hard resetting link
ata3: SATA link down (SStatus 0 SControl 300)
ata3: EH complete
ata3: exception Emask 0x50 SAct 0x0 SErr 0x40d0802 action 0xe frozen
ata3: irq_stat 0x00000040, connection status changed
ata3: SError: { RecovComm HostInt PHYRdyChg CommWake 10B8B DevExch }
ata3: hard resetting link
ata3: link is slow to respond, please be patient (ready=0)
ata3: COMRESET failed (errno=-16)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3: exception Emask 0x50 SAct 0x0 SErr 0x80800 action 0x7 t4
ata3: irq_stat 0x08000002, interface fatal error
ata3: SError: { HostInt 10B8B }
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-8: WDC WD10EACS-00D6B0, 01.01A01, max UDMA/133
ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata3.00: configured for UDMA/133
ata3: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x1 t3
ata3: irq_stat 0x08000002, interface fatal error
ata3.00: configured for UDMA/133
ata3: EH complete
scsi 2:0:0:0: Direct-Access ATA WDC WD10EACS-00D 01.0 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 2:0:0:0: [sdc] Attached SCSI disk
ata3: exception Emask 0x50 SAct 0x0 SErr 0x90800 action 0xe frozen
ata3: irq_stat 0x00400000, PHY RDY changed
ata3: SError: { HostInt PHYRdyChg 10B8B }
ata3: hard resetting link
ata3: SATA link down (SStatus 0 SControl 300)
ata3: hard resetting link
ata3: link is slow to respond, please be patient (ready=0)
ata3: COMRESET failed (errno=-16)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: configured for UDMA/133
ata3: exception Emask 0x50 SAct 0x0 SErr 0x80800 action 0xf t4
ata3: irq_stat 0x00000040, connection status changed
ata3: SError: { HostInt 10B8B }
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata3.00: revalidation failed (errno=-5)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata3.00: revalidation failed (errno=-5)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: qc timeout (cmd 0xec)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata3.00: revalidation failed (errno=-5)
ata3.00: disabled
ata3: hard resetting link
sd 2:0:0:0: rejecting I/O to offline device
sd 2:0:0:0: rejecting I/O to offline device
sd 2:0:0:0: rejecting I/O to offline device
sd 2:0:0:0: rejecting I/O to offline device
sd 2:0:0:0: [sdc] READ CAPACITY failed
sd 2:0:0:0: [sdc] Result: hostbyte=0x01 driverbyte=0x00
sd 2:0:0:0: [sdc] Sense not available.
sd 2:0:0:0: rejecting I/O to offline device
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 00 00 00
sd 2:0:0:0: rejecting I/O to offline device
sd 2:0:0:0: [sdc] Asking for cache data failed
sd 2:0:0:0: [sdc] Assuming drive cache: write through
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-8: WDC WD10EACS-00D6B0, 01.01A01, max UDMA/133
ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata3.00: configured for UDMA/133
ata3: exception Emask 0x50 SAct 0x0 SErr 0x80800 action 0x7 t3
ata3: irq_stat 0x08000002, interface fatal error
ata3: SError: { HostInt 10B8B }
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata3.00: revalidation failed (errno=-5)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata3.00: revalidation failed (errno=-5)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: configured for UDMA/133
ata3: limiting SATA link speed to 1.5 Gbps
ata3: exception Emask 0x50 SAct 0x0 SErr 0x80800 action 0x7 t2
ata3: irq_stat 0x08000002, interface fatal error
ata3: SError: { HostInt 10B8B }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/133
ata3: EH complete
ata3.00: detaching (SCSI 2:0:0:0)
sd 2:0:0:0: [sdc] Stopping disk
scsi 2:0:0:0: Direct-Access ATA WDC WD10EACS-00D 01.0 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 2:0:0:0: [sdc] Attached SCSI disk
ata3.00: exception Emask 0x50 SAct 0x1c SErr 0x280900 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
ata3.00: cmd 60/04:10:41:94:8e/00:00:0e:00:00/40 tag 2 ncq 2048 in
res 40/00:24:47:94:8e/00:00:0e:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/02:18:45:94:8e/00:00:0e:00:00/40 tag 3 ncq 1024 in
res 40/00:24:47:94:8e/00:00:0e:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/50:20:47:94:8e/00:00:0e:00:00/40 tag 4 ncq 40960 in
res 40/00:24:47:94:8e/00:00:0e:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/133
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: limiting speed to UDMA/100:PIO4
ata3.00: exception Emask 0x10 SAct 0xf SErr 0x280100 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData 10B8B BadCRC }
ata3.00: cmd 60/a8:00:ef:3b:39/00:00:3a:00:00/40 tag 0 ncq 86016 in
res 40/00:0c:97:3c:39/00:00:3a:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/58:08:97:3c:39/00:00:3a:00:00/40 tag 1 ncq 45056 in
res 40/00:0c:97:3c:39/00:00:3a:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/a8:10:ef:3c:39/00:00:3a:00:00/40 tag 2 ncq 86016 in
res 40/00:0c:97:3c:39/00:00:3a:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/58:18:97:3d:39/00:00:3a:00:00/40 tag 3 ncq 45056 in
res 40/00:0c:97:3c:39/00:00:3a:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/100
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x10 SAct 0xf SErr 0x280100 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData 10B8B BadCRC }
ata3.00: cmd 60/a8:00:ef:49:39/00:00:3a:00:00/40 tag 0 ncq 86016 in
res 40/00:1c:97:49:39/00:00:3a:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/58:08:97:4a:39/00:00:3a:00:00/40 tag 1 ncq 45056 in
res 40/00:1c:97:49:39/00:00:3a:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/a8:10:ef:48:39/00:00:3a:00:00/40 tag 2 ncq 86016 in
res 40/00:1c:97:49:39/00:00:3a:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/58:18:97:49:39/00:00:3a:00:00/40 tag 3 ncq 45056 in
res 40/00:1c:97:49:39/00:00:3a:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/100
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x10 SAct 0xb SErr 0x280100 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData 10B8B BadCRC }
ata3.00: cmd 60/a8:00:ef:56:39/00:00:3a:00:00/40 tag 0 ncq 86016 in
res 40/00:0c:97:57:39/00:00:3a:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/58:08:97:57:39/00:00:3a:00:00/40 tag 1 ncq 45056 in
res 40/00:0c:97:57:39/00:00:3a:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/58:18:97:56:39/00:00:3a:00:00/40 tag 3 ncq 45056 in
res 40/00:0c:97:57:39/00:00:3a:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/100
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x10 SAct 0xf SErr 0x280100 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData 10B8B BadCRC }
ata3.00: cmd 60/a8:00:ef:a1:39/00:00:3a:00:00/40 tag 0 ncq 86016 in
res 40/00:04:ef:a1:39/00:00:3a:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/a8:08:ef:a2:39/00:00:3a:00:00/40 tag 1 ncq 86016 in
res 40/00:04:ef:a1:39/00:00:3a:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/58:10:97:a3:39/00:00:3a:00:00/40 tag 2 ncq 45056 in
res 40/00:04:ef:a1:39/00:00:3a:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/58:18:97:a2:39/00:00:3a:00:00/40 tag 3 ncq 45056 in
res 40/00:04:ef:a1:39/00:00:3a:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/100
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: limiting speed to UDMA/33:PIO4
ata3.00: exception Emask 0x10 SAct 0x1 SErr 0x280100 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData 10B8B BadCRC }
ata3.00: cmd 60/72:00:25:24:8e/00:00:0e:00:00/40 tag 0 ncq 58368 in
res 40/00:04:25:24:8e/00:00:0e:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x10 SAct 0x3 SErr 0x280100 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData 10B8B BadCRC }
ata3.00: cmd 60/a8:00:98:3a:8e/00:00:0e:00:00/40 tag 0 ncq 86016 in
res 40/00:0c:40:3b:8e/00:00:0e:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/56:08:40:3b:8e/00:00:0e:00:00/40 tag 1 ncq 44032 in
res 40/00:0c:40:3b:8e/00:00:0e:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x10 SAct 0x1 SErr 0x280100 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData 10B8B BadCRC }
ata3.00: cmd 60/a0:00:f7:76:8e/00:00:0e:00:00/40 tag 0 ncq 81920 in
res 40/00:04:f7:76:8e/00:00:0e:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x10 SAct 0x1 SErr 0x280100 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData 10B8B BadCRC }
ata3.00: cmd 60/f8:00:9f:88:8e/00:00:0e:00:00/40 tag 0 ncq 126976 in
res 40/00:04:9f:88:8e/00:00:0e:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x10 SAct 0x1 SErr 0x280100 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData 10B8B BadCRC }
ata3.00: cmd 60/f8:00:9f:b1:8e/00:00:0e:00:00/40 tag 0 ncq 126976 in
res 40/00:04:9f:b1:8e/00:00:0e:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x10 SAct 0x3 SErr 0x280100 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData 10B8B BadCRC }
ata3.00: cmd 60/a8:00:ba:76:8e/00:00:0e:00:00/40 tag 0 ncq 86016 in
res 40/00:0c:62:77:8e/00:00:0e:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/35:08:62:77:8e/00:00:0e:00:00/40 tag 1 ncq 27136 in
res 40/00:0c:62:77:8e/00:00:0e:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x10 SAct 0x1 SErr 0x280100 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData 10B8B BadCRC }
ata3.00: cmd 60/20:00:d7:33:8e/00:00:0e:00:00/40 tag 0 ncq 16384 in
res 40/00:04:d7:33:8e/00:00:0e:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x50 SAct 0x1fe0 SErr 0x480900 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B Handshk }
ata3.00: cmd 61/00:28:e7:90:bc/04:00:13:00:00/40 tag 5 ncq 524288 out
res 40/00:64:a7:84:c1/00:00:13:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/00:30:e7:94:bc/04:00:13:00:00/40 tag 6 ncq 524288 out
res 40/00:64:a7:84:c1/00:00:13:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/08:38:e7:98:bc/00:00:13:00:00/40 tag 7 ncq 4096 out
res 40/00:64:a7:84:c1/00:00:13:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/70:40:ef:98:bc/02:00:13:00:00/40 tag 8 ncq 319488 out
res 40/00:64:a7:84:c1/00:00:13:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/08:48:9f:00:bf/00:00:13:00:00/40 tag 9 ncq 4096 out
res 40/00:64:a7:84:c1/00:00:13:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/00:50:9f:80:c1/04:00:13:00:00/40 tag 10 ncq 524288 out
res 40/00:64:a7:84:c1/00:00:13:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/08:58:9f:84:c1/00:00:13:00:00/40 tag 11 ncq 4096 out
res 40/00:64:a7:84:c1/00:00:13:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/60:60:a7:84:c1/01:00:13:00:00/40 tag 12 ncq 180224 out
res 40/00:64:a7:84:c1/00:00:13:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x50 SAct 0xffff SErr 0x480900 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B Handshk }
ata3.00: cmd 61/00:00:ef:72:08/02:00:1a:00:00/40 tag 0 ncq 262144 out
res 40/00:14:57:ed:11/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/08:08:d7:ec:0d/00:00:1a:00:00/40 tag 1 ncq 4096 out
res 40/00:14:57:ed:11/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/10:10:57:ed:11/00:00:1a:00:00/40 tag 2 ncq 8192 out
res 40/00:14:57:ed:11/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/00:18:1f:f6:fd/04:00:19:00:00/40 tag 3 ncq 524288 out
res 40/00:14:57:ed:11/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/00:20:1f:fa:fd/04:00:19:00:00/40 tag 4 ncq 524288 out
res 40/00:14:57:ed:11/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/00:28:1f:fe:fd/04:00:19:00:00/40 tag 5 ncq 524288 out
res 40/00:14:57:ed:11/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/00:30:1f:02:fe/04:00:19:00:00/40 tag 6 ncq 524288 out
res 40/00:14:57:ed:11/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/00:38:1f:06:fe/04:00:19:00:00/40 tag 7 ncq 524288 out
res 40/00:14:57:ed:11/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/00:40:1f:0a:fe/04:00:19:00:00/40 tag 8 ncq 524288 out
res 40/00:14:57:ed:11/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/80:48:1f:0e:fe/02:00:19:00:00/40 tag 9 ncq 327680 out
res 40/00:14:57:ed:11/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/00:50:7f:e2:fe/04:00:19:00:00/40 tag 10 ncq 524288 out
res 40/00:14:57:ed:11/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/70:58:7f:e6:fe/01:00:19:00:00/40 tag 11 ncq 188416 out
res 40/00:14:57:ed:11/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/08:60:a7:e3:02/00:00:1a:00:00/40 tag 12 ncq 4096 out
res 40/00:14:57:ed:11/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/08:68:4f:6e:04/00:00:1a:00:00/40 tag 13 ncq 4096 out
res 40/00:14:57:ed:11/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/00:70:ef:6e:08/04:00:1a:00:00/40 tag 14 ncq 524288 out
res 40/00:14:57:ed:11/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/08:78:d7:6d:12/00:00:1a:00:00/40 tag 15 ncq 4096 out
res 40/00:14:57:ed:11/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
ata3.00: cmd 60/00:00:37:71:8e/01:00:0e:00:00/40 tag 0 ncq 131072 in
res 40/00:04:37:71:8e/00:00:0e:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x10 SAct 0x1 SErr 0x280100 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData 10B8B BadCRC }
ata3.00: cmd 60/00:00:37:71:8e/01:00:0e:00:00/40 tag 0 ncq 131072 in
res 40/00:04:37:71:8e/00:00:0e:00:00/40 Emask 0x10 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
ata3.00: cmd 60/08:00:8f:93:00/00:00:00:00:00/40 tag 0 ncq 4096 in
res 40/00:04:8f:93:00/00:00:00:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x50 SAct 0x2 SErr 0x280900 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
ata3.00: cmd 60/08:08:b7:93:00/00:00:00:00:00/40 tag 1 ncq 4096 in
res 40/00:0c:b7:93:00/00:00:00:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x50 SAct 0x300 SErr 0x480900 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B Handshk }
ata3.00: cmd 61/00:40:b7:7e:af/04:00:34:00:00/40 tag 8 ncq 524288 out
res 40/00:4c:b7:82:af/00:00:34:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/e0:48:b7:82:af/03:00:34:00:00/40 tag 9 ncq 507904 out
res 40/00:4c:b7:82:af/00:00:34:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
ata3.00: cmd 60/00:00:37:77:8e/01:00:0e:00:00/40 tag 0 ncq 131072 in
res 40/00:04:37:77:8e/00:00:0e:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
ata3.00: cmd 60/08:00:7f:95:00/00:00:00:00:00/40 tag 0 ncq 4096 in
res 40/00:04:7f:95:00/00:00:00:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
ata3.00: cmd 60/08:00:67:96:00/00:00:00:00:00/40 tag 0 ncq 4096 in
res 40/00:04:67:96:00/00:00:00:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x50 SAct 0x1001 SErr 0x480900 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B Handshk }
ata3.00: cmd 61/00:00:d7:1c:7f/04:00:38:00:00/40 tag 0 ncq 524288 out
res 40/00:64:d7:20:7f/00:00:38:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/08:60:d7:20:7f/02:00:38:00:00/40 tag 12 ncq 266240 out
res 40/00:64:d7:20:7f/00:00:38:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x50 SAct 0x3e1 SErr 0x480900 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B Handshk }
ata3.00: cmd 61/00:00:cf:12:0a/04:00:39:00:00/40 tag 0 ncq 524288 out
res 40/00:04:cf:12:0a/00:00:39:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/00:28:6f:e8:09/04:00:39:00:00/40 tag 5 ncq 524288 out
res 40/00:04:cf:12:0a/00:00:39:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/08:30:6f:ec:09/01:00:39:00:00/40 tag 6 ncq 135168 out
res 40/00:04:cf:12:0a/00:00:39:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/08:38:c7:12:0a/00:00:39:00:00/40 tag 7 ncq 4096 out
res 40/00:04:cf:12:0a/00:00:39:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/00:40:cf:16:0a/04:00:39:00:00/40 tag 8 ncq 524288 out
res 40/00:04:cf:12:0a/00:00:39:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/48:48:cf:1a:0a/03:00:39:00:00/40 tag 9 ncq 430080 out
res 40/00:04:cf:12:0a/00:00:39:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x50 SAct 0x601 SErr 0x480900 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B Handshk }
ata3.00: cmd 60/08:00:a7:99:00/00:00:00:00:00/40 tag 0 ncq 4096 in
res 40/00:04:a7:99:00/00:00:00:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/00:48:af:47:18/04:00:39:00:00/40 tag 9 ncq 524288 out
res 40/00:04:a7:99:00/00:00:00:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/50:50:af:4b:18/00:00:39:00:00/40 tag 10 ncq 40960 out
res 40/00:04:a7:99:00/00:00:00:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x50 SAct 0x2 SErr 0x280900 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
ata3.00: cmd 60/08:08:c7:99:00/00:00:00:00:00/40 tag 1 ncq 4096 in
res 40/00:0c:c7:99:00/00:00:00:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
ata3.00: cmd 60/08:00:ff:99:00/00:00:00:00:00/40 tag 0 ncq 4096 in
res 40/00:04:ff:99:00/00:00:00:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x50 SAct 0x3e1 SErr 0x480900 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B Handshk }
ata3.00: cmd 61/00:00:4f:63:71/04:00:3a:00:00/40 tag 0 ncq 524288 out
res 40/00:04:4f:63:71/00:00:3a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/00:28:47:5b:71/04:00:3a:00:00/40 tag 5 ncq 524288 out
res 40/00:04:4f:63:71/00:00:3a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/00:30:47:5f:71/04:00:3a:00:00/40 tag 6 ncq 524288 out
res 40/00:04:4f:63:71/00:00:3a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/08:38:47:63:71/00:00:3a:00:00/40 tag 7 ncq 4096 out
res 40/00:04:4f:63:71/00:00:3a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/00:40:4f:67:71/04:00:3a:00:00/40 tag 8 ncq 524288 out
res 40/00:04:4f:63:71/00:00:3a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/50:48:4f:6b:71/00:00:3a:00:00/40 tag 9 ncq 40960 out
res 40/00:04:4f:63:71/00:00:3a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x50 SAct 0x3c1 SErr 0x480900 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B Handshk }
ata3.00: cmd 61/00:00:ff:e7:8e/04:00:3a:00:00/40 tag 0 ncq 524288 out
res 40/00:04:ff:e7:8e/00:00:3a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/00:30:f7:e3:8e/04:00:3a:00:00/40 tag 6 ncq 524288 out
res 40/00:04:ff:e7:8e/00:00:3a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/08:38:f7:e7:8e/00:00:3a:00:00/40 tag 7 ncq 4096 out
res 40/00:04:ff:e7:8e/00:00:3a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/00:40:ff:eb:8e/04:00:3a:00:00/40 tag 8 ncq 524288 out
res 40/00:04:ff:e7:8e/00:00:3a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 61/50:48:ff:ef:8e/00:00:3a:00:00/40 tag 9 ncq 40960 out
res 40/00:04:ff:e7:8e/00:00:3a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x50 SAct 0x1 SErr 0x480900 action 0x6 frozen
ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B Handshk }
ata3.00: cmd 61/00:00:97:3a:bb/04:00:3a:00:00/40 tag 0 ncq 524288 out
res 40/00:04:97:3a:bb/00:00:3a:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
-----sorry for the spam
You see? For me this is looking like you have a "Wackelkontakt"/loose connection/flaky joint for whatever reason. The ata3-link goes repeatedly up and down which makes the sd2 on top of it fail. So, out of my point of view, it doesn't matter if you have blockerrors or not because these are atop of the lower layers which do fail. So, as long as this is not fixed from the ground up, No-Go with whichever FS. This is one point of view. Another perspective could be that indeed the disk is faulty and causing the link to fail because of that, but you cannot tell for sure until you have either checked with another disk, or checked with this disk and the cabling. And do not try to write to this disk as long as the dmesg shows the link going up and down and resetting like this! No filesystem likes that! So back to the cabling, why would that be? It's common, there are LOTS of (electrically) bad cables out, i have experienced that myself. Maybe the plugs are bad/loose fitting? So when you start the PC it vibrates, or the external enclosure vibrates and shakes some contact loose. Can all happen. Maybe your desk shakes it loose when you type and it is on it. Can happen too. I'm telling that because it did happen to me :-) But maybe i'm wrong here and it is indeed the disk which is faulty, though i doubt that, and as i said, you can't be sure until you checked either the disk for itself, directly attached to rule out the external enclosure and its cabling, or you checked another disk with that and don't have the errors which i cited above.
Offline
#28 2008-11-19 18:37:02
- Dieter@be
- Forum Fellow
- From: Belgium
- Registered: 2006-11-05
- Posts: 2,001
- Website
Re: "No Space Left on Device" (df -h shows 45GB free!!)
Sata connectors are really known for coming loose, so this could be it (hopefully, for the topic starter)
< Daenyth> and he works prolifically
4 8 15 16 23 42
Offline
#29 2008-11-20 02:38:14
- ogronom
- Member
- From: Toronto, Canada
- Registered: 2008-05-06
- Posts: 123
Re: "No Space Left on Device" (df -h shows 45GB free!!)
Isn't it the famous problem of deleting/opening files on raid? (when df and du gives a different information, and usually one have less free space than he should)
Offline
#30 2008-11-20 07:56:35
- robmaloy
- Member
- From: Germany
- Registered: 2008-05-14
- Posts: 263
Re: "No Space Left on Device" (df -h shows 45GB free!!)
just delete your "backups" and "rip" them from "cds" again 
☃ Snowman ☃
Offline