You are not logged in.

Pages: 1

#1 2009-01-17 03:31:17

Cyrusm
Member
From: Bozeman, MT
Registered: 2007-11-15
Posts: 1,053

[SOLVED] 2.6.28 upgrade, wireless interface has disapeared

this is on a Dell Inspiron 1525,
wireless card is a Broadcom 4312 running the
broadcom driver in accordance with http://wiki.archlinux.org/index.php/Broadcom_BCM4312

previously my wireless interface was "eth1"  and after  the upgrade, I do not know what it is. 
I know that it is not eth0, eth1, wlan0, wlan1, 

does any one have an idea?  or know how to find out?

any help is appreciated,

Last edited by Cyrusm (2009-01-17 19:34:01)

Hofstadter's Law:
           It always takes longer than you expect, even when you take into account Hofstadter's Law.

Offline

#2 2009-01-17 04:01:36

josomebody
Member
Registered: 2008-06-20
Posts: 190

Re: [SOLVED] 2.6.28 upgrade, wireless interface has disapeared

Standard troubleshooting stuff:
Is the module loaded? Can we see the output of lsmod?
Can we see the output of ifconfig -a?
dmesg might be helpful too to see if anything's going on at boot you should know about.

: () { : | :& } ;:

Offline

#3 2009-01-17 17:19:02

Cyrusm
Member
From: Bozeman, MT
Registered: 2007-11-15
Posts: 1,053

Re: [SOLVED] 2.6.28 upgrade, wireless interface has disapeared

lsmod

Module                  Size  Used by
i915                   58372  2 
drm                    83624  3 i915
ipv6                  260212  12 
ext2                   66184  1 
uvcvideo               57736  0 
compat_ioctl32          3072  1 uvcvideo
videodev               34176  1 uvcvideo
v4l1_compat            15364  2 uvcvideo,videodev
joydev                 11712  0 
sdhci_pci               9088  0 
sdhci                  17028  1 sdhci_pci
ohci1394               31280  0 
mmc_core               46876  1 sdhci
i2c_i801               10896  0 
uhci_hcd               24592  0 
ehci_hcd               36876  0 
psmouse                55828  0 
ieee1394               80068  1 ohci1394
sg                     26804  0 
snd_pcsp               11048  0 
serio_raw               7172  0 
usbcore               136976  4 uvcvideo,uhci_hcd,ehci_hcd
i2c_core               22804  1 i2c_i801
iTCO_wdt               12836  0 
iTCO_vendor_support     4996  1 iTCO_wdt
video                  18576  0 
output                  4608  1 video
intel_agp              27580  1 
agpgart                31572  3 drm,intel_agp
wmi                     7848  0 
dcdbas                  9120  0 
thermal                17180  2 
fan                     6276  0 
button                  7824  0 
battery                12036  0 
ac                      6020  0 
evdev                  11296  0 
snd_seq_oss            31872  0 
snd_seq_midi_event      8192  1 snd_seq_oss
snd_seq                49968  4 snd_seq_oss,snd_seq_midi_event
snd_seq_device          8332  2 snd_seq_oss,snd_seq
snd_hda_intel         411956  0 
snd_hwdep               9092  1 snd_hda_intel
snd_pcm_oss            40320  0 
snd_pcm                70020  3 snd_pcsp,snd_hda_intel,snd_pcm_oss
snd_timer              21384  2 snd_seq,snd_pcm
snd_page_alloc         10120  2 snd_hda_intel,snd_pcm
snd_mixer_oss          16512  1 snd_pcm_oss
snd                    50852  10 snd_pcsp,snd_seq_oss,snd_seq,snd_seq_device,snd_hda_intel,snd_hwdep,snd_pcm_oss,snd_pcm,snd_timer,snd_mixer_oss
soundcore               8160  1 snd
ieee80211_crypt_tkip    10752  0 
ieee80211_crypt         6532  1 ieee80211_crypt_tkip
sky2                   48260  0 
cpufreq_powersave       3456  0 
cpufreq_ondemand        8972  1 
acpi_cpufreq            9868  1 
freq_table              5632  2 cpufreq_ondemand,acpi_cpufreq
processor              41388  4 thermal,acpi_cpufreq
rtc_cmos               12332  0 
rtc_core               17564  1 rtc_cmos
rtc_lib                 4480  1 rtc_core
ext3                  126856  2 
jbd                    46996  1 ext3
mbcache                 8708  2 ext2,ext3
sr_mod                 16708  0 
cdrom                  35360  1 sr_mod
sd_mod                 26904  5 
ata_piix               23300  0 
ahci                   30988  4 
ata_generic             6788  0 
pata_acpi               6016  0 
libata                158240  4 ata_piix,ahci,ata_generic,pata_acpi
scsi_mod              102036  4 sg,sr_mod,sd_mod,libata

ifconfig -a

eth0      Link encap:Ethernet  HWaddr 00:1D:09:48:D4:F1  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:16 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

and dmesg

BIOS EBDA/lowmem at: 0009f000/0009f000
Linux version 2.6.28-ARCH (root@T-POWA-LX) (gcc version 4.3.2 (GCC) ) #1 SMP PREEMPT Tue Jan 6 10:26:22 UTC 2009
KERNEL supported cpus:
  Intel GenuineIntel
  AMD AuthenticAMD
  NSC Geode by NSC
  Cyrix CyrixInstead
  Centaur CentaurHauls
  Transmeta GenuineTMx86
  Transmeta TransmetaCPU
  UMC UMC UMC UMC
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
 BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007f66d800 (usable)
 BIOS-e820: 000000007f66d800 - 0000000080000000 (reserved)
 BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fed18000 - 00000000fed1c000 (reserved)
 BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
 BIOS-e820: 00000000feda0000 - 00000000feda6000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
 BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
DMI 2.4 present.
last_pfn = 0x7f66d max_arch_pfn = 0x100000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Scanning 2 areas for low memory corruption
modified physical RAM map:
 modified: 0000000000000000 - 0000000000002000 (usable)
 modified: 0000000000002000 - 0000000000006000 (reserved)
 modified: 0000000000006000 - 0000000000007000 (usable)
 modified: 0000000000007000 - 0000000000010000 (reserved)
 modified: 0000000000010000 - 0000000000092000 (usable)
 modified: 000000000009f000 - 00000000000a0000 (reserved)
 modified: 0000000000100000 - 000000007f66d800 (usable)
 modified: 000000007f66d800 - 0000000080000000 (reserved)
 modified: 00000000f8000000 - 00000000fc000000 (reserved)
 modified: 00000000fec00000 - 00000000fec10000 (reserved)
 modified: 00000000fed18000 - 00000000fed1c000 (reserved)
 modified: 00000000fed20000 - 00000000fed90000 (reserved)
 modified: 00000000feda0000 - 00000000feda6000 (reserved)
 modified: 00000000fee00000 - 00000000fee10000 (reserved)
 modified: 00000000ffe00000 - 0000000100000000 (reserved)
kernel direct mapping tables up to 377fe000 @ 10000-16000
RAMDISK: 7f5c2000 - 7f65d051
Allocated new RAMDISK: 0055f000 - 005fa051
Move RAMDISK from 000000007f5c2000 - 000000007f65d050 to 0055f000 - 005fa050
ACPI: RSDP 000FBC60, 0024 (r2 DELL  )
ACPI: XSDT 7F66F200, 0064 (r1 DELL    M08     27D8030A ASL        61)
ACPI: FACP 7F66F09C, 00F4 (r4 DELL    M08     27D8030A ASL        61)
ACPI: DSDT 7F66F800, 5495 (r2 INT430 SYSFexxx     1001 INTL 20050624)
ACPI: FACS 7F67E000, 0040
ACPI: HPET 7F66F300, 0038 (r1 DELL    M08            1 ASL        61)
ACPI: APIC 7F66F400, 0068 (r1 DELL    M08     27D8030A ASL        47)
ACPI: MCFG 7F66F3C0, 003E (r16 DELL    M08     27D8030A ASL        61)
ACPI: SLIC 7F66F49C, 0176 (r1 DELL    M08     27D8030A ASL        61)
ACPI: OSFR 7F66EA00, 008A (r1 DELL    M08     27D8030A ASL        61)
ACPI: BOOT 7F66EFC0, 0028 (r1 DELL    M08     27D8030A ASL        61)
ACPI: SSDT 7F66DA02, 04CC (r1  PmRef    CpuPm     3000 INTL 20050624)
ACPI: Local APIC address 0xfee00000
1150MB HIGHMEM available.
887MB LOWMEM available.
  mapped low ram: 0 - 377fe000
  low ram: 00000000 - 377fe000
  bootmap 00012000 - 00018f00
(9 early reservations) ==> bootmem [0000000000 - 00377fe000]
  #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
  #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
  #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
  #3 [0000100000 - 000055b520]    TEXT DATA BSS ==> [0000100000 - 000055b520]
  #4 [000055c000 - 000055f000]    INIT_PG_TABLE ==> [000055c000 - 000055f000]
  #5 [000009f000 - 0000100000]    BIOS reserved ==> [000009f000 - 0000100000]
  #6 [0000010000 - 0000012000]          PGTABLE ==> [0000010000 - 0000012000]
  #7 [000055f000 - 00005fa051]      NEW RAMDISK ==> [000055f000 - 00005fa051]
  #8 [0000012000 - 0000019000]          BOOTMAP ==> [0000012000 - 0000019000]
Zone PFN ranges:
  DMA      0x00000000 -> 0x00001000
  Normal   0x00001000 -> 0x000377fe
  HighMem  0x000377fe -> 0x0007f66d
Movable zone start PFN for each node
early_node_map[4] active PFN ranges
    0: 0x00000000 -> 0x00000002
    0: 0x00000006 -> 0x00000007
    0: 0x00000010 -> 0x00000092
    0: 0x00000100 -> 0x0007f66d
On node 0 totalpages: 521714
free_area_init_node: node 0, pgdat c0406580, node_mem_map c1000000
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 3941 pages, LIFO batch:0
  Normal zone: 1744 pages used for memmap
  Normal zone: 221486 pages, LIFO batch:31
  HighMem zone: 2301 pages used for memmap
  HighMem zone: 292210 pages, LIFO batch:31
  Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PM: Registered nosave memory: 0000000000002000 - 0000000000006000
PM: Registered nosave memory: 0000000000007000 - 0000000000010000
PM: Registered nosave memory: 0000000000092000 - 000000000009f000
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 0000000000100000
Allocating PCI resources starting at 88000000 (gap: 80000000:78000000)
PERCPU: Allocating 36864 bytes of per cpu data
NR_CPUS: 16, nr_cpu_ids: 2, nr_node_ids 1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 517637
Kernel command line: root=/dev/disk/by-uuid/c2a2b89a-f733-4529-a25d-bba20a6faaad ro
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Extended CMOS year: 2000
Fast TSC calibration using PIT
Detected 1728.750 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Scanning for low memory corruption every 60 seconds
Memory: 2063652k/2087348k available (2228k kernel code, 22360k reserved, 1026k data, 332k init, 1178044k highmem)
virtual kernel memory layout:
    fixmap  : 0xffee8000 - 0xfffff000   (1116 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf7ffe000 - 0xff7fe000   ( 120 MB)
    lowmem  : 0xc0000000 - 0xf77fe000   ( 887 MB)
      .init : 0xc0433000 - 0xc0486000   ( 332 kB)
      .data : 0xc032d139 - 0xc042db5c   (1026 kB)
      .text : 0xc0100000 - 0xc032d139   (2228 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
hpet clockevent registered
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
Calibrating delay loop (skipped), value calculated using timer frequency.. 3458.56 BogoMIPS (lpj=5762500)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
using mwait in idle threads.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20080926
ACPI: Checking initramfs for custom DSDT
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Pentium(R) Dual  CPU  T2370  @ 1.73GHz stepping 0d
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3459.09 BogoMIPS (lpj=5763345)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Pentium(R) Dual  CPU  T2370  @ 1.73GHz stepping 0d
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (6918.65 BogoMIPS).
net_namespace: 768 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MCFG configuration 0: base f8000000 segment 0 buses 0 - 63
PCI: MCFG area at f8000000 reserved in E820
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
ACPI: EC: Look up EC in DSDT
ACPI: BIOS _OSI(Linux) query ignored
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:02.0: reg 10 64bit mmio: [0xfea00000-0xfeafffff]
pci 0000:00:02.0: reg 18 64bit mmio: [0xe0000000-0xefffffff]
pci 0000:00:02.0: reg 20 io port: [0xeff8-0xefff]
pci 0000:00:02.1: reg 10 64bit mmio: [0xfeb00000-0xfebfffff]
pci 0000:00:1a.0: reg 20 io port: [0x6f20-0x6f3f]
pci 0000:00:1a.1: reg 20 io port: [0x6f00-0x6f1f]
pci 0000:00:1a.7: reg 10 32bit mmio: [0xfed1c400-0xfed1c7ff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: PME# disabled
pci 0000:00:1b.0: reg 10 64bit mmio: [0xfe9fc000-0xfe9fffff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0x6f80-0x6f9f]
pci 0000:00:1d.1: reg 20 io port: [0x6f60-0x6f7f]
pci 0000:00:1d.2: reg 20 io port: [0x6f40-0x6f5f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xfed1c000-0xfed1c3ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 1080-10bf claimed by ICH6 GPIO
pci 0000:00:1f.1: reg 10 io port: [0x1f0-0x1f7]
pci 0000:00:1f.1: reg 14 io port: [0x3f4-0x3f7]
pci 0000:00:1f.1: reg 18 io port: [0x170-0x177]
pci 0000:00:1f.1: reg 1c io port: [0x374-0x377]
pci 0000:00:1f.1: reg 20 io port: [0x6fa0-0x6faf]
pci 0000:00:1f.2: reg 10 io port: [0x6eb0-0x6eb7]
pci 0000:00:1f.2: reg 14 io port: [0x6eb8-0x6ebb]
pci 0000:00:1f.2: reg 18 io port: [0x6ec0-0x6ec7]
pci 0000:00:1f.2: reg 1c io port: [0x6ec8-0x6ecb]
pci 0000:00:1f.2: reg 20 io port: [0x6ee0-0x6eff]
pci 0000:00:1f.2: reg 24 32bit mmio: [0xfe9fb800-0xfe9fbfff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 10 32bit mmio: [0xfe9fb700-0xfe9fb7ff]
pci 0000:00:1f.3: reg 20 io port: [0x10c0-0x10df]
pci 0000:09:00.0: reg 10 64bit mmio: [0xfe8fc000-0xfe8fffff]
pci 0000:09:00.0: reg 18 io port: [0xde00-0xdeff]
pci 0000:09:00.0: supports D1 D2
pci 0000:09:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:09:00.0: PME# disabled
pci 0000:00:1c.0: bridge io port: [0xd000-0xdfff]
pci 0000:00:1c.0: bridge 32bit mmio: [0xfe800000-0xfe8fffff]
pci 0000:0b:00.0: reg 10 64bit mmio: [0xfe7fc000-0xfe7fffff]
pci 0000:0b:00.0: supports D1 D2
pci 0000:0b:00.0: PME# supported from D0 D3hot D3cold
pci 0000:0b:00.0: PME# disabled
pci 0000:00:1c.1: bridge 32bit mmio: [0xfe700000-0xfe7fffff]
pci 0000:00:1c.4: bridge io port: [0xc000-0xcfff]
pci 0000:00:1c.4: bridge 32bit mmio: [0xfe400000-0xfe6fffff]
pci 0000:00:1c.4: bridge 64bit mmio pref: [0xf0000000-0xf01fffff]
pci 0000:02:09.0: reg 10 32bit mmio: [0xfe3ff800-0xfe3fffff]
pci 0000:02:09.0: supports D1 D2
pci 0000:02:09.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:09.0: PME# disabled
pci 0000:02:09.1: reg 10 32bit mmio: [0xfe3ff500-0xfe3ff5ff]
pci 0000:02:09.1: supports D1 D2
pci 0000:02:09.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:09.1: PME# disabled
pci 0000:02:09.2: reg 10 32bit mmio: [0xfe3ff600-0xfe3ff6ff]
pci 0000:02:09.2: supports D1 D2
pci 0000:02:09.2: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:09.2: PME# disabled
pci 0000:02:09.3: reg 10 32bit mmio: [0xfe3ff700-0xfe3ff7ff]
pci 0000:02:09.3: supports D1 D2
pci 0000:02:09.3: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:09.3: PME# disabled
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge 32bit mmio: [0xfe300000-0xfe3fffff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP05._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *10
ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 11) *5
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 *7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:0a: io resource (0x1000-0x1005) overlaps 0000:00:1f.0 BAR 7 (0x1000-0x107f), disabling
pnp 00:0a: io resource (0x1008-0x100f) overlaps 0000:00:1f.0 BAR 7 (0x1000-0x107f), disabling
pnp 00:0b: io resource (0x1006-0x1007) overlaps 0000:00:1f.0 BAR 7 (0x1000-0x107f), disabling
pnp 00:0b: io resource (0x100a-0x1059) overlaps 0000:00:1f.0 BAR 7 (0x1000-0x107f), disabling
pnp 00:0b: io resource (0x1060-0x107f) overlaps 0000:00:1f.0 BAR 7 (0x1000-0x107f), disabling
pnp 00:0b: io resource (0x1010-0x102f) overlaps 0000:00:1f.0 BAR 7 (0x1000-0x107f), disabling
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: iomem range 0xff800000-0xff8fffff has been reserved
system 00:01: iomem range 0xffc00000-0xffcfffff has been reserved
system 00:06: ioport range 0xc80-0xcff could not be reserved
system 00:09: iomem range 0xfed00000-0xfed003ff has been reserved
system 00:0a: ioport range 0x900-0x97f has been reserved
system 00:0a: ioport range 0x4d0-0x4d1 has been reserved
system 00:0b: ioport range 0xf400-0xf4fe has been reserved
system 00:0b: ioport range 0x1080-0x10bf has been reserved
system 00:0b: ioport range 0x10c0-0x10df has been reserved
system 00:0b: ioport range 0x809-0x809 has been reserved
system 00:0c: iomem range 0x0-0x9efff could not be reserved
system 00:0c: iomem range 0x9f000-0x9ffff could not be reserved
system 00:0c: iomem range 0xc0000-0xcffff could not be reserved
system 00:0c: iomem range 0xe0000-0xfffff could not be reserved
system 00:0c: iomem range 0x100000-0x7f66d7ff could not be reserved
system 00:0c: iomem range 0x7f66d800-0x7f6fffff has been reserved
system 00:0c: iomem range 0x7f700000-0x7f7fffff has been reserved
system 00:0c: iomem range 0x7f700000-0x7fefffff could not be reserved
system 00:0c: iomem range 0xffe00000-0xffffffff has been reserved
system 00:0c: iomem range 0xffa00000-0xffbfffff has been reserved
system 00:0c: iomem range 0xfec00000-0xfec0ffff has been reserved
system 00:0c: iomem range 0xfee00000-0xfee0ffff has been reserved
system 00:0c: iomem range 0xfed20000-0xfed8ffff has been reserved
system 00:0c: iomem range 0xfeda0000-0xfeda3fff has been reserved
system 00:0c: iomem range 0xfeda4000-0xfeda4fff has been reserved
system 00:0c: iomem range 0xfeda5000-0xfeda5fff has been reserved
system 00:0c: iomem range 0xfeda6000-0xfeda6fff has been reserved
system 00:0c: iomem range 0xfed18000-0xfed1bfff has been reserved
system 00:0c: iomem range 0xf8000000-0xfbffffff has been reserved
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:09
pci 0000:00:1c.0:   IO window: 0xd000-0xdfff
pci 0000:00:1c.0:   MEM window: 0xfe800000-0xfe8fffff
pci 0000:00:1c.0:   PREFETCH window: disabled
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:0b
pci 0000:00:1c.1:   IO window: disabled
pci 0000:00:1c.1:   MEM window: 0xfe700000-0xfe7fffff
pci 0000:00:1c.1:   PREFETCH window: disabled
pci 0000:00:1c.4: PCI bridge, secondary bus 0000:0c
pci 0000:00:1c.4:   IO window: 0xc000-0xcfff
pci 0000:00:1c.4:   MEM window: 0xfe400000-0xfe6fffff
pci 0000:00:1c.4:   PREFETCH window: 0x000000f0000000-0x000000f01fffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1e.0:   IO window: disabled
pci 0000:00:1e.0:   MEM window: 0xfe300000-0xfe3fffff
pci 0000:00:1e.0:   PREFETCH window: disabled
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.4: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
bus: 00 index 0 io port: [0x00-0xffff]
bus: 00 index 1 mmio: [0x000000-0xffffffff]
bus: 09 index 0 io port: [0xd000-0xdfff]
bus: 09 index 1 mmio: [0xfe800000-0xfe8fffff]
bus: 09 index 2 mmio: [0x0-0x0]
bus: 09 index 3 mmio: [0x0-0x0]
bus: 0b index 0 mmio: [0x0-0x0]
bus: 0b index 1 mmio: [0xfe700000-0xfe7fffff]
bus: 0b index 2 mmio: [0x0-0x0]
bus: 0b index 3 mmio: [0x0-0x0]
bus: 0c index 0 io port: [0xc000-0xcfff]
bus: 0c index 1 mmio: [0xfe400000-0xfe6fffff]
bus: 0c index 2 mmio: [0xf0000000-0xf01fffff]
bus: 0c index 3 mmio: [0x0-0x0]
bus: 02 index 0 mmio: [0x0-0x0]
bus: 02 index 1 mmio: [0xfe300000-0xfe3fffff]
bus: 02 index 2 mmio: [0x0-0x0]
bus: 02 index 3 io port: [0x00-0xffff]
bus: 02 index 4 mmio: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs... done
Freeing initrd memory: 620k freed
Simple Boot Flag at 0x79 set to 0x1
apm: BIOS not found.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1732
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:02.0: Boot video device
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: found MSI capability
pcieport-driver 0000:00:1c.0: irq 767 for MSI/MSI-X
pci_express 0000:00:1c.0:pcie00: allocate port service
pci_express 0000:00:1c.0:pcie02: allocate port service
pci_express 0000:00:1c.0:pcie03: allocate port service
pcieport-driver 0000:00:1c.1: setting latency timer to 64
pcieport-driver 0000:00:1c.1: found MSI capability
pcieport-driver 0000:00:1c.1: irq 766 for MSI/MSI-X
pci_express 0000:00:1c.1:pcie00: allocate port service
pci_express 0000:00:1c.1:pcie02: allocate port service
pci_express 0000:00:1c.1:pcie03: allocate port service
pcieport-driver 0000:00:1c.4: setting latency timer to 64
pcieport-driver 0000:00:1c.4: found MSI capability
pcieport-driver 0000:00:1c.4: irq 765 for MSI/MSI-X
pci_express 0000:00:1c.4:pcie00: allocate port service
pci_express 0000:00:1c.4:pcie02: allocate port service
pci_express 0000:00:1c.4:pcie03: allocate port service
isapnp: Scanning for PnP cards...
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
isapnp: No Plug & Play device found
Serial: 8250/16550 driver4 ports, IRQ sharing disabled
input: Macintosh mouse button emulation as /class/input/input0
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 332k freed
SCSI subsystem initialized
input: AT Translated Set 2 keyboard as /class/input/input1
libata version 3.00 loaded.
pata_acpi 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pata_acpi 0000:00:1f.1: setting latency timer to 64
pata_acpi 0000:00:1f.1: PCI INT A disabled
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ahci 0000:00:1f.2: irq 764 for MSI/MSI-X
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x5 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems 
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
ata1: SATA max UDMA/133 abar m2048@0xfe9fb800 port 0xfe9fb900 irq 764
ata2: DUMMY
ata3: SATA max UDMA/133 abar m2048@0xfe9fb800 port 0xfe9fba00 irq 764
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: ST9160821AS, 3.CDE, max UDMA/133
ata1.00: 312581808 sectors, multi 8: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata3: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      ST9160821AS      3.CD PQ: 0 ANSI: 5
ata_piix 0000:00:1f.1: version 2.12
ata_piix 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi3 : ata_piix
scsi4 : ata_piix
ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x6fa0 irq 14
ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x6fa8 irq 15
ata4.00: ATAPI: Optiarc DVD+/-RW AD-5560A, DD11, max UDMA/33
ata4.00: configured for UDMA/33
ata5: port disabled. ignoring.
scsi 3:0:0:0: CD-ROM            Optiarc  DVD+-RW AD-5560A DD11 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda:<4>Driver 'sr' needs updating - please use bus_type methods
 sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 3:0:0:0: Attached scsi CD-ROM sr0
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
rtc_cmos 00:04: RTC can wake from S4
rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
ACPI: SSDT 7F66E538, 0244 (r1  PmRef  Cpu0Ist     3000 INTL 20050624)
ACPI: SSDT 7F66DECE, 05E5 (r1  PmRef  Cpu0Cst     3001 INTL 20050624)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
processor ACPI_CPU:00: registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: SSDT 7F66E77C, 00C4 (r1  PmRef  Cpu1Ist     3000 INTL 20050624)
ACPI: SSDT 7F66E4B3, 0085 (r1  PmRef  Cpu1Cst     3000 INTL 20050624)
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
processor ACPI_CPU:01: registered as cooling_device1
ACPI: Processor [CPU1] (supports 8 throttling states)
Marking TSC unstable due to TSC halts in idle
sky2 driver version 1.22
sky2 0000:09:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
sky2 0000:09:00.0: setting latency timer to 64
sky2 0000:09:00.0: Yukon-2 FE+ chip revision 0
sky2 0000:09:00.0: irq 763 for MSI/MSI-X
sky2 eth0: addr 00:1d:09:48:d4:f1
ieee80211_crypt: registered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'TKIP'
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
HDA Intel 0000:00:1b.0: setting latency timer to 64
input: HDA Digital PCBeep as /class/input/input2
Clocksource tsc unstable (delta = -186825573 ns)
ACPI: AC Adapter [AC] (off-line)
ACPI: Battery Slot [BAT0] (battery present)
input: Lid Switch as /class/input/input3
ACPI: Lid Switch [LID]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PBTN]
input: Sleep Button (CM) as /class/input/input5
ACPI: Sleep Button (CM) [SBTN]
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THM] (30 C)
dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
ACPI: WMI: Mapper loaded
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel 965GM Chipset
agpgart-intel 0000:00:00.0: detected 7676K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
acpi device:31: registered as cooling_device2
input: Video Bus as /class/input/input6
ACPI: Video Device [VID] (multi-head: yes  rom: no  post: no)
ACPI Warning (nspredef-0357): \_SB_.PCI0.VID2._DOD: Return Package has no elements (empty) [20080926]
input: Video Bus as /class/input/input7
ACPI: Video Device [VID2] (multi-head: yes  rom: no  post: no)
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.04
iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
input: PC Speaker as /class/input/input8
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 3:0:0:0: Attached scsi generic sg1 type 5
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) -> IRQ 22
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1a.7: irq 22, io mem 0xfed1c400
uhci_hcd: USB Universal Host Controller Interface driver
Error: Driver 'pcspkr' is already registered, aborting...
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1a.0: irq 20, io base 0x00006f20
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfed1c000
ohci1394 0000:02:09.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 21, io base 0x00006f00
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.0: irq 20, io base 0x00006f80
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.1: irq 21, io base 0x00006f60
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.2: irq 22, io base 0x00006f40
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16]  MMIO=[fe3ff800-fe3fffff]  Max Packet=[2048]  IR/IT contexts=[4/4]
sdhci-pci 0000:02:09.1: SDHCI controller found [1180:0822] (rev 22)
sdhci-pci 0000:02:09.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
mmc0: SDHCI controller on PCI [0000:02:09.1] using DMA
usb 1-1: new high speed USB device using ehci_hcd and address 2
input: PS/2 Mouse as /class/input/input9
usb 1-1: configuration #1 chosen from 1 choice
input: AlpsPS/2 ALPS GlidePoint as /class/input/input10
Linux video capture interface: v2.00
uvcvideo: Found UVC 1.00 device Laptop Integrated Webcam (05a9:2640)
uvcvideo: Failed to query (135) UVC control 1 (unit 0) : -32 (exp. 26).
input: Laptop Integrated Webcam as /class/input/input11
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
EXT3 FS on sda3, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 265064k swap on /dev/sda2.  Priority:-1 extents:1 across:265064k
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[424fc00011c851a1]
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
[drm] Initialized drm 1.1.0 20060810
pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:02.0: setting latency timer to 64
pci 0000:00:02.0: irq 762 for MSI/MSI-X
[drm] Initialized i915 1.6.0 20080730 on minor 0
X:2500 conflicting memory types e0000000-f0000000 write-combining<->uncached-minus
reserve_memtype failed 0xe0000000-0xf0000000, track write-combining, req write-combining
X:2500 conflicting memory types e0000000-f0000000 write-combining<->uncached-minus
reserve_memtype failed 0xe0000000-0xf0000000, track write-combining, req write-combining
X:2525 freeing invalid memtype e0000000-f0000000

Hofstadter's Law:
           It always takes longer than you expect, even when you take into account Hofstadter's Law.

Offline

#4 2009-01-17 17:26:19

knownbad
Member
Registered: 2008-05-04
Posts: 16

Re: [SOLVED] 2.6.28 upgrade, wireless interface has disapeared

run following then reboot.  sl failed after kernel upgrade.  i'll assume you had wl in rc.conf/modules alraedy

sudo insmod /lib/modules/2.6.27-ARCH/kernel/drivers/net/wireless/wl.ko

Last edited by knownbad (2009-01-17 17:26:39)

Offline

#5 2009-01-17 17:53:13

Cyrusm
Member
From: Bozeman, MT
Registered: 2007-11-15
Posts: 1,053

Re: [SOLVED] 2.6.28 upgrade, wireless interface has disapeared

I ran insmod, but received an error 

insmod: error inserting '/lib/modules/2.6.27-ARCH/kernel/drivers/net/wireless/wl.ko': -1 Invalid module format

Hofstadter's Law:
           It always takes longer than you expect, even when you take into account Hofstadter's Law.

Offline

#6 2009-01-17 17:57:26

Cyrusm
Member
From: Bozeman, MT
Registered: 2007-11-15
Posts: 1,053

Re: [SOLVED] 2.6.28 upgrade, wireless interface has disapeared

I also just noticed that '/lib/modules/2.6.27...../wireless/' only contains wl.ko, but '/lib/modules/2.6.28....../wireless/' contains a whole slew of files for a variety of wireless cards(b43, prism54, rt2x00, and many others).  but no wl.ko

Hofstadter's Law:
           It always takes longer than you expect, even when you take into account Hofstadter's Law.

Offline

#7 2009-01-17 19:27:04

mcmillan
Member
Registered: 2006-04-06
Posts: 737

Re: [SOLVED] 2.6.28 upgrade, wireless interface has disapeared

Looks like the module hasn't been updated since the new kernel came out. When there's a new kernel version you need to recompile kernel modules so they will work together.

Offline

#8 2009-01-17 19:35:41

Cyrusm
Member
From: Bozeman, MT
Registered: 2007-11-15
Posts: 1,053

Re: [SOLVED] 2.6.28 upgrade, wireless interface has disapeared

Thanks mcmillan,  I actually had just done that and then I read your post.   It works now,
I just had to rebuild the module for the new kernel and reinstall and now I'm back online B)

Hofstadter's Law:
           It always takes longer than you expect, even when you take into account Hofstadter's Law.

Offline

#9 2009-01-17 21:37:43

knownbad
Member
Registered: 2008-05-04
Posts: 16

Re: [SOLVED] 2.6.28 upgrade, wireless interface has disapeared

sorry, i thoguht i edited sudo "insmod /lib/modules/2.6.28-ARCH/kernel/drivers/net/wireless/wl.ko" but guess that's not true.   sorry about your grief.

Offline

Pages: 1

Board footer

Powered by FluxBB