Arch Linux

cakofony

Member

Registered: 2009-04-14

Posts: 13

fglrx crash on startup

I am quite new to arch linux (moved over from gentoo yesterday).  I havent had linux on my system with my radeon 4870x2 though, and I'm not sure whats going wrong >.<

For a few tries, when I would start X, I would get some red squiggly stuff at the top of the screen, and it would freeze.
now my display just turns off, or goes into its power saving mode when I start x, and I cannot go back to a virtual terminal.
Once X came up, but there were some large squares with scanlines, and my cursor was a scanlined box....  artifacts everywhere! :-O  I know its not a problem with the card, because it works perfectly in windows.

I am using the default xorg.conf that aticonfig gave me

I would post the Xorg.0.log, but my computer locks up whenever I try to start x, so I cant get it...

Last edited by cakofony (2009-04-14 17:28:26)

darthaxul

Member

Registered: 2008-09-24

Posts: 156

Re: fglrx crash on startup

How did u get ur fglrx module built? I haven't been able to build mine for past 3 months for the 4800x2, so I have been using the vesa drive.
you dont need to startx just to post ur Xorg.log, if u have a fat32 partition or ntfs-3g module u can copy it to that partition and use ur other system to view it.

cakofony

Member

Registered: 2009-04-14

Posts: 13

Re: fglrx crash on startup

I used the one from AUR.  After I reboot, the files are always blank :-(
I even tried using the ati driver, which worked before, but it does the same thing (I think it might defualt to fglrx since I had to uninstall libgl, as it conflicts)

cakofony

Member

Registered: 2009-04-14

Posts: 13

Re: fglrx crash on startup

I can get X to start when I disable dri, but then I have no 2d or 3d acceleration at all :-(

cakofony

Member

Registered: 2009-04-14

Posts: 13

Re: fglrx crash on startup

Xorg.0.log

X.Org X Server 1.6.0
Release Date: 2009-2-25
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.29-ARCH x86_64
Current Operating System: Linux cakobox 2.6.29-ARCH #1 SMP PREEMPT Wed Apr 8 12:39:28 CEST 2009 x86_64
Build Date: 10 April 2009  01:30:50PM

    Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Wed Apr 15 00:16:13 2009
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "aticonfig Layout"
(**) |-->Screen "aticonfig-Screen[0]-0" (0)
(**) |   |-->Monitor "aticonfig-Monitor[0]-0"
(**) |   |-->Device "aticonfig-Device[0]-0"
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/TTF" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/share/fonts/Type1" does not exist.
    Entry deleted from font path.
(==) FontPath set to:
    /usr/share/fonts/misc,
    /usr/share/fonts/100dpi:unscaled,
    /usr/share/fonts/75dpi:unscaled,
    built-ins
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) Cannot locate a core pointer device.
(II) Cannot locate a core keyboard device.
(II) The server relies on HAL to provide the list of input devices.
    If no devices become available, reconfigure HAL or disable AllowEmptyInput.
(II) Loader magic: 0x1540
(II) Module ABI versions:
    X.Org ANSI C Emulation: 0.4
    X.Org Video Driver: 5.0
    X.Org XInput driver : 4.0
    X.Org Server Extension : 2.0
(II) Loader running on linux
(++) using VT number 7

(--) PCI:*(0@3:0:0) ATI Technologies Inc R700 [Radeon HD 4870 X2] rev 0, Mem @ 0xc0000000/268435456, 0xfe8e0000/65536, I/O @ 0x0000a000/256, BIOS @ 0x????????/131072
(--) PCI: (0@4:0:0) ATI Technologies Inc R700 [Radeon HD 4870 X2] rev 0, Mem @ 0xd0000000/268435456, 0xfe9f0000/65536, I/O @ 0x0000b000/256, BIOS @ 0x????????/131072
(II) Open ACPI successful (/var/run/acpid.socket)
(II) System resource ranges:
    [0] -1    0    0xffffffff - 0xffffffff (0x1) MX[b]
    [1] -1    0    0x000f0000 - 0x000fffff (0x10000) MX[b]
    [2] -1    0    0x000c0000 - 0x000effff (0x30000) MX[b]
    [3] -1    0    0x00000000 - 0x0009ffff (0xa0000) MX[b]
    [4] -1    0    0x0000ffff - 0x0000ffff (0x1) IX[b]
    [5] -1    0    0x00000000 - 0x00000000 (0x1) IX[b]
(II) "extmod" will be loaded by default.
(II) "dbe" will be loaded by default.
(II) "glx" will be loaded by default.
(II) "record" will be loaded by default.
(II) "dri" will be loaded by default.
(II) "dri2" will be loaded by default.
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
    compiled for 1.6.0, module version = 1.0.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
    compiled for 1.6.0, module version = 1.0.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
    compiled for 7.4.0, module version = 1.0.0
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
    compiled for 1.6.0, module version = 1.13.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
    compiled for 7.4.0, module version = 1.0.0
(II) Loading extension XFree86-DRI
(II) Loading sub module "fglrxdrm"
(II) LoadModule: "fglrxdrm"
(II) Loading /usr/lib/xorg/modules/linux//libfglrxdrm.so
(II) Module fglrxdrm: vendor="FireGL - ATI Technologies Inc."
    compiled for 1.4.99.906, module version = 8.60.40
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions//libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
    compiled for 1.6.0, module version = 1.0.0
    ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "fglrx"
(II) Loading /usr/lib/xorg/modules/drivers//fglrx_drv.so
(II) Module fglrx: vendor="FireGL - ATI Technologies Inc."
    compiled for 1.4.99.906, module version = 8.60.40
    Module class: X.Org Video Driver
(II) Primary Device is: PCI 03@00:00:0
(WW) Falling back to old probe method for fglrx
(II) ATI Proprietary Linux Driver Version Identifier:8.60.40
(II) ATI Proprietary Linux Driver Release Identifier: 8.60.4                               
(II) ATI Proprietary Linux Driver Build Date: Mar 14 2009 21:46:40
(II) PCS database file /etc/ati/amdpcsdb not found
(II)   Creating PCS database from initial defaults instead
(WW) This ATI Proprietary Linux Driver does not guarantee support of video driver ABI higher than 2.0
(WW) Video driver ABI version of the X server is 5.0
(WW) fglrx: No matching Device section for instance (BusID PCI:0@4:0:0) found
(--) Chipset Supported AMD Graphics Processor (0x9441) found
(WW) fglrx: No matching Device section for instance (BusID PCI:0@3:0:1) found
(**) ChipID override: 0x9441
(**) Chipset Supported AMD Graphics Processor (0x9441) found
(II) AMD Video driver is running on a device belonging to a group targeted for this release
(II) AMD Video driver is signed
(II) resource ranges after xf86ClaimFixedResources() call:
    [0] -1    0    0xffffffff - 0xffffffff (0x1) MX[b]
    [1] -1    0    0x000f0000 - 0x000fffff (0x10000) MX[b]
    [2] -1    0    0x000c0000 - 0x000effff (0x30000) MX[b]
    [3] -1    0    0x00000000 - 0x0009ffff (0xa0000) MX[b]
    [4] -1    0    0x0000ffff - 0x0000ffff (0x1) IX[b]
    [5] -1    0    0x00000000 - 0x00000000 (0x1) IX[b]
(II) fglrx(0): pEnt->device->identifier=0x99a500
(II) pEnt->device->identifier=(nil)
(II) resource ranges after probing:
    [0] -1    0    0xffffffff - 0xffffffff (0x1) MX[b]
    [1] -1    0    0x000f0000 - 0x000fffff (0x10000) MX[b]
    [2] -1    0    0x000c0000 - 0x000effff (0x30000) MX[b]
    [3] -1    0    0x00000000 - 0x0009ffff (0xa0000) MX[b]
    [4] 0    0    0x000a0000 - 0x000affff (0x10000) MS[b]
    [5] 0    0    0x000b0000 - 0x000b7fff (0x8000) MS[b]
    [6] 0    0    0x000b8000 - 0x000bffff (0x8000) MS[b]
    [7] -1    0    0x0000ffff - 0x0000ffff (0x1) IX[b]
    [8] -1    0    0x00000000 - 0x00000000 (0x1) IX[b]
    [9] 0    0    0x000003b0 - 0x000003bb (0xc) IS[b]
    [10] 0    0    0x000003c0 - 0x000003df (0x20) IS[b]
(II) Setting vga for screen 0.
(II) fglrx(0): === [atiddxPreInit] === begin
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
    compiled for 1.6.0, module version = 0.1.0
    ABI class: X.Org Video Driver, version 5.0
(II) fglrx(0): PCI bus 3 card 0 func 0
(**) fglrx(0): Depth 24, (--) framebuffer bpp 32
(II) fglrx(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
(==) fglrx(0): Default visual is TrueColor
(**) fglrx(0): Option "dri" "off"
(**) fglrx(0): Option "DPMS" "true"
(II) fglrx(0): 10BitPixelFormat disabled by default
(==) fglrx(0): RGB weight 888
(II) fglrx(0): Using 8 bits per RGB (8 bit DAC)
(==) fglrx(0): Gamma Correction for I is 0x06419064
(==) fglrx(0): Gamma Correction for II is 0x06419064
(==) fglrx(0): Buffer Tiling is ON
(II) Loading sub module "fglrxdrm"
(II) LoadModule: "fglrxdrm"
(II) Reloading /usr/lib/xorg/modules/linux//libfglrxdrm.so
(--) fglrx(0): Chipset: "ATI Radeon HD 4870 X2" (Chipset = 0x9441)
(--) fglrx(0): (PciSubVendor = 0x1002, PciSubDevice = 0x2542)
(--) fglrx(0): board vendor info: original ATI graphics adapter
(--) fglrx(0): Linear framebuffer (phys) at 0xc0000000
(--) fglrx(0): MMIO registers at 0xfe8e0000
(--) fglrx(0): I/O port at 0x0000a000
(==) fglrx(0): ROM-BIOS at 0x000c0000
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib/xorg/modules//libint10.so
(II) Module int10: vendor="X.Org Foundation"
    compiled for 1.6.0, module version = 1.0.0
    ABI class: X.Org Video Driver, version 5.0
(II) fglrx(0): Primary V_BIOS segment is: 0xc000
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/lib/xorg/modules//libvbe.so
(II) Module vbe: vendor="X.Org Foundation"
    compiled for 1.6.0, module version = 1.1.0
    ABI class: X.Org Video Driver, version 5.0
(II) fglrx(0): VESA BIOS detected
(II) fglrx(0): VESA VBE Version 3.0
(II) fglrx(0): VESA VBE Total Mem: 16384 kB
(II) fglrx(0): VESA VBE OEM: ATI ATOMBIOS
(II) fglrx(0): VESA VBE OEM Software Rev: 11.7
(II) fglrx(0): VESA VBE OEM Vendor: (C) 1988-2005, ATI Technologies Inc.
(II) fglrx(0): VESA VBE OEM Product: RV770
(II) fglrx(0): VESA VBE OEM Product Rev: 01.00
(II) fglrx(0): ATI Video BIOS revision 9 or later detected
(II) fglrx(0): PCI bus 4 card 0 func 0
(**) fglrx(0): Chipset: "ATI Radeon HD 4870 X2" (Chipset = 0x9441)
(**) fglrx(0): (PciSubVendor = 0x1002, PciSubDevice = 0x2042)
(**) fglrx(0): board vendor info: original ATI graphics adapter
(--) fglrx(0): Linear framebuffer (phys) at 0xd0000000
(--) fglrx(0): MMIO registers at 0xfe9f0000
(==) fglrx(0): ROM-BIOS at 0x000c0000
(II) fglrx(0): ATI Video BIOS revision 9 or later detected
(--) fglrx(0): Video RAM: 1048576 kByte, Type: GDDR5
(II) fglrx(0): PCIE card detected
(II) fglrx(0): board/chipset is supported by this driver (original ATI board)
(II) fglrx(0): MultiAsic found: Check whether two adapters have the same configuration
ulGetFrameBufferSize: Framebuffer memory size 1073741824
ulGetFrameBufferSize: Framebuffer memory size 1073741824
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 11, (OK)
drmOpenByBusid: Searching for BusID PCI:3:0:0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 11, (OK)
drmOpenByBusid: drmOpenMinor returns 11
drmOpenByBusid: drmGetBusid reports PCI:3:0:0
(II) fglrx(0): Using adapter: 3:0.0.
(--) fglrx(0): Video RAM: 1048576 kByte, Type: GDDR5
(II) fglrx(0): [FB] MC range(MCFBBase = 0xf00000000, MCFBSize = 0x40000000)
(II) fglrx(0): PCIE card detected
(--) fglrx(0): Using per-process page tables (PPPT) as GART.
(II) fglrx(0): board/chipset is supported by this driver (original ATI board)
(II) fglrx(0): RandR 1.2 support is enabled!
(II) fglrx(0): RandR 1.2 rotation support is enabled!
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 12, (OK)
drmOpenByBusid: Searching for BusID PCI:4:0:0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 12, (OK)
drmOpenByBusid: drmOpenMinor returns 12
drmOpenByBusid: drmGetBusid reports PCI:3:0:0
drmOpenDevice: node name is /dev/dri/card1
drmOpenDevice: open result is 12, (OK)
drmOpenByBusid: drmOpenMinor returns 12
drmOpenByBusid: drmGetBusid reports PCI:4:0:0
(II) fglrx(0): Using adapter: 4:0.0.
(II) fglrx(0): [FB] MC range(MCFBBase = 0xf00000000, MCFBSize = 0x40000000)
(II) fglrx(0): [pcie] 2021888 kB allocated
(II) fglrx(0): [drm] DRM buffer queue setup: nbufs = 100 bufsize = 65536
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) fglrx(0): ***Display: ConnectedDisplayTypes=0x00000008, disabled=0x00000000
(II) fglrx(0): Connected Display1: DFP on internal TMDS [tmds1]
(II) fglrx(0): Display1 EDID data ---------------------------
(II) fglrx(0): Manufacturer: GWY  Model: 96e  Serial#: 16843009
(II) fglrx(0): Year: 2008  Week: 21
(II) fglrx(0): EDID Version: 1.3
(II) fglrx(0): Digital Display Input
(II) fglrx(0): Max Image Size [cm]: horiz.: 52  vert.: 32
(II) fglrx(0): Gamma: 2.20
(II) fglrx(0): DPMS capabilities: StandBy Suspend Off
(II) fglrx(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
(II) fglrx(0): First detailed timing is preferred mode
(II) fglrx(0): redX: 0.661 redY: 0.328   greenX: 0.217 greenY: 0.677
(II) fglrx(0): blueX: 0.146 blueY: 0.075   whiteX: 0.313 whiteY: 0.329
(II) fglrx(0): Supported VESA Video Modes:
(II) fglrx(0): 720x400@70Hz
(II) fglrx(0): 640x480@60Hz
(II) fglrx(0): 640x480@72Hz
(II) fglrx(0): 640x480@75Hz
(II) fglrx(0): 800x600@56Hz
(II) fglrx(0): 800x600@60Hz
(II) fglrx(0): 800x600@72Hz
(II) fglrx(0): 800x600@75Hz
(II) fglrx(0): 1024x768@60Hz
(II) fglrx(0): 1024x768@70Hz
(II) fglrx(0): 1024x768@75Hz
(II) fglrx(0): 1280x1024@75Hz
(II) fglrx(0): Manufacturer's mask: 0
(II) fglrx(0): Supported Future Video Modes:
(II) fglrx(0): #0: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
(II) fglrx(0): #1: hsize: 1152  vsize 864  refresh: 75  vid: 20337
(II) fglrx(0): #2: hsize: 1440  vsize 900  refresh: 60  vid: 149
(II) fglrx(0): #3: hsize: 1440  vsize 900  refresh: 75  vid: 3989
(II) fglrx(0): #4: hsize: 1680  vsize 1050  refresh: 60  vid: 179
(II) fglrx(0): Supported additional Video Mode:
(II) fglrx(0): clock: 154.0 MHz   Image Size:  518 x 324 mm
(II) fglrx(0): h_active: 1920  h_sync: 1968  h_sync_end 2000 h_blank_end 2080 h_border: 0
(II) fglrx(0): v_active: 1200  v_sync: 1203  v_sync_end 1209 v_blanking: 1235 v_border: 0
(II) fglrx(0): Monitor name: FHD2401
(II) fglrx(0): Ranges: V min: 56 V max: 76 Hz, H min: 31 H max: 83 kHz, PixClock max 160 MHz
(II) fglrx(0): Serial No: MEV85D0R01631
(II) fglrx(0): EDID (in hex):
(II) fglrx(0):     00ffffffffffff001ef96e0901010101
(II) fglrx(0):     1512010380342078ea4995a95437ad25
(II) fglrx(0):     135054afcf008180714f9500950fb300
(II) fglrx(0):     010101010101283c80a070b023403020
(II) fglrx(0):     360006442100001a000000fc00464844
(II) fglrx(0):     323430310a2020202020000000fd0038
(II) fglrx(0):     4c1f5310000a202020202020000000ff
(II) fglrx(0):     004d4556383544305230313633310014
(II) fglrx(0): End of Display1 EDID data --------------------
(II) fglrx(0): Output DFP1 using monitor section aticonfig-Monitor[0]-0
(II) fglrx(0): Output DFP2 has no monitor section
(II) fglrx(0): Output CRT1 has no monitor section
(II) fglrx(0): Output CRT2 has no monitor section
(II) fglrx(0): Output TV has no monitor section
(II) fglrx(0): Output COMPONENT_VIDEO has no monitor section
(II) fglrx(0): EDID vendor "GWY", prod id 2414
(II) fglrx(0): Using EDID range info for horizontal sync
(II) fglrx(0): Using EDID range info for vertical refresh
(II) fglrx(0): Printing DDC gathered Modelines:
(II) fglrx(0): Modeline "1920x1200"x0.0  154.00  1920 1968 2000 2080  1200 1203 1209 1235 +hsync -vsync (74.0 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(II) fglrx(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)
(II) fglrx(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz)
(II) fglrx(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) fglrx(0): Modeline "1152x864"x0.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz)
(II) fglrx(0): Modeline "1440x900"x0.0   88.75  1440 1488 1520 1600  900 903 909 926 +hsync -vsync (55.5 kHz)
(II) fglrx(0): Modeline "1440x900"x0.0  136.75  1440 1536 1688 1936  900 903 909 942 -hsync +vsync (70.6 kHz)
(II) fglrx(0): Modeline "1680x1050"x0.0  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
(II) fglrx(0): Output DFP1 connected
(II) fglrx(0): Output DFP2 disconnected
(II) fglrx(0): Output CRT1 disconnected
(II) fglrx(0): Output CRT2 disconnected
(II) fglrx(0): Output TV disconnected
(II) fglrx(0): Output COMPONENT_VIDEO disconnected
(II) fglrx(0): Using exact sizes for initial modes
(II) fglrx(0): Output DFP1 using initial mode 1920x1200
(**) fglrx(0): Display dimensions: (520, 320) mm
(**) fglrx(0): DPI set to (93, 152)
(==) fglrx(0): Using gamma correction (1.0, 1.0, 1.0)
(==) fglrx(0): QBS disabled
(==) fglrx(0): FAST_SWAP disabled
(==) fglrx(0):  PseudoColor visuals disabled
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
    compiled for 1.6.0, module version = 1.0.0
    ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(==) fglrx(0): NoAccel = NO
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/lib/xorg/modules//libxaa.so
(II) Module xaa: vendor="X.Org Foundation"
    compiled for 1.6.0, module version = 1.2.1
    ABI class: X.Org Video Driver, version 5.0
(**) fglrx(0): NoDRI = YES
(==) fglrx(0): Capabilities: 0x00000000
(==) fglrx(0): CapabilitiesEx: 0x00000000
(==) fglrx(0): cpuFlags: 0x80000009
(==) fglrx(0): OpenGL ClientDriverName: "fglrx_dri.so"
(II) fglrx(0): [pcie] 2021888 kB allocated
(II) fglrx(0): [drm] DRM buffer queue setup: nbufs = 100 bufsize = 65536
(==) fglrx(0): UseFastTLS=0
(==) fglrx(0): BlockSignalsOnLock=1
(II) fglrx(0): Direct rendering enabled
(II) fglrx(0): Direct rendering enabled for slave 0
(II) fglrx(0): AC Adapter is used
(II) fglrx(0): AC Adapter is used
(II) fglrx(0): Interrupt handler installed at IRQ 32.
(II) fglrx(0): Interrupt handler installed at IRQ 33.
(II) fglrx(0): Finished Initialize PPLIB!
(WW) fglrx(0): Unable to register ADL handler for 0x00C00000
(II) fglrx(0): Finished Initialize PPLIB for slave 0!
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC?  No, I don't.
(II) resource ranges after preInit:
    [0] -1    0    0xffffffff - 0xffffffff (0x1) MX[b]
    [1] -1    0    0x000f0000 - 0x000fffff (0x10000) MX[b]
    [2] -1    0    0x000c0000 - 0x000effff (0x30000) MX[b]
    [3] -1    0    0x00000000 - 0x0009ffff (0xa0000) MX[b]
    [4] 0    0    0x000a0000 - 0x000affff (0x10000) MS[b](OprU)
    [5] 0    0    0x000b0000 - 0x000b7fff (0x8000) MS[b](OprU)
    [6] 0    0    0x000b8000 - 0x000bffff (0x8000) MS[b](OprU)
    [7] -1    0    0x0000ffff - 0x0000ffff (0x1) IX[b]
    [8] -1    0    0x00000000 - 0x00000000 (0x1) IX[b]
    [9] 0    0    0x000003b0 - 0x000003bb (0xc) IS[b](OprU)
    [10] 0    0    0x000003c0 - 0x000003df (0x20) IS[b](OprU)
(WW) fglrx(0): ***********************************
(WW) fglrx(0): * DRI initialization disabled!    *
(WW) fglrx(0): * 2D acceleraton available (MMIO) *
(WW) fglrx(0): * no 3D acceleration available    *
(WW) fglrx(0): ***********************************
(II) fglrx(0): FBADPhys: 0xf00000000 FBMappedSize: 0x10000000
(II) fglrx(0): FBMM initialized for area (0,0)-(1920,8191)
(II) fglrx(0): FBMM auto alloc for area (0,0)-(1920,1920) (front color buffer - assumption)
(II) fglrx(0): Largest offscreen area available: 1920 x 6271
(==) fglrx(0): Backing store disabled
(II) Loading extension FGLRXEXTENSION
(II) Loading extension ATITVOUT
(**) fglrx(0): DPMS enabled
(II) fglrx(0): Initialized in-driver Xinerama extension
(WW) fglrx(0): Textured Video not supported without DRI enabled.
(II) LoadModule: "glesx"
(II) Loading /usr/lib/xorg/modules//glesx.so
(II) Module glesx: vendor="X.Org Foundation"
    compiled for 1.4.99.906, module version = 1.0.0
(II) Loading extension GLESX
(II) fglrx(0): GLESX enableFlags = 78
(II) fglrx(0): Acceleration enabled
(II) LoadModule: "amdxmm"
(II) Loading /usr/lib/xorg/modules//amdxmm.so
(II) Module amdxmm: vendor="X.Org Foundation"
    compiled for 1.4.99.906, module version = 1.0.0
(EE) fglrx(0): XMM failed to open CMMQS connection.
(II) fglrx(0): XMM failed to initialize!
(II) fglrx(0): Enable composite support successfully
(WW) fglrx(0): Option "VendorName" is not used
(WW) fglrx(0): Option "ModelName" is not used
(==) fglrx(0): Silken mouse enabled
(==) fglrx(0): Using HW cursor of display infrastructure!
(==) fglrx(0): Using software cursor
(II) fglrx(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(II) fglrx(0): atiddxDisplayScreenLoadPalette: numColors: 256
(--) RandR disabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) AIGLX: Screen 0 is not DRI capable
[glesx] __glESXExtensionInit: No GL ES2.0 capable screen found!
(II) fglrx(0): Setting screen physical size to 518 x 324
swlDalGetDisplayIndex:ERROR: The number of Active Displays is 0
swlDalGetDisplayIndex:ERROR: The number of Active Displays is 0
(II) config/hal: Adding input device Macintosh mouse button emulation
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input//evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
    compiled for 1.6.0, module version = 2.2.1
    Module class: X.Org XInput Driver
    ABI class: X.Org XInput driver, version 4.0
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event0"
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Configuring as mouse
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
(**) Macintosh mouse button emulation: (accel) filter chain progression: 2.00
(**) Macintosh mouse button emulation: (accel) filter stage 0: 20.00 ms
(**) Macintosh mouse button emulation: (accel) set acceleration profile 0
(II) config/hal: Adding input device Logitech USB Gaming Mouse
(**) Logitech USB Gaming Mouse: always reports core events
(**) Logitech USB Gaming Mouse: Device: "/dev/input/event6"
(II) Logitech USB Gaming Mouse: Found 16 mouse buttons
(II) Logitech USB Gaming Mouse: Found x and y relative axes
(II) Logitech USB Gaming Mouse: Found scroll wheel(s)
(II) Logitech USB Gaming Mouse: Configuring as mouse
(**) Logitech USB Gaming Mouse: YAxisMapping: buttons 4 and 5
(**) Logitech USB Gaming Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Logitech USB Gaming Mouse" (type: MOUSE)
(**) Logitech USB Gaming Mouse: (accel) keeping acceleration scheme 1
(**) Logitech USB Gaming Mouse: (accel) filter chain progression: 2.00
(**) Logitech USB Gaming Mouse: (accel) filter stage 0: 20.00 ms
(**) Logitech USB Gaming Mouse: (accel) set acceleration profile 0
(II) config/hal: Adding input device USB-compliant keyboard
(**) USB-compliant keyboard: always reports core events
(**) USB-compliant keyboard: Device: "/dev/input/event5"
(II) USB-compliant keyboard: Found 10 mouse buttons
(II) USB-compliant keyboard: Found x and y relative axes
(II) USB-compliant keyboard: Found scroll wheel(s)
(II) USB-compliant keyboard: Found keys
(II) USB-compliant keyboard: Configuring as mouse
(II) USB-compliant keyboard: Configuring as keyboard
(**) USB-compliant keyboard: YAxisMapping: buttons 4 and 5
(**) USB-compliant keyboard: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "USB-compliant keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(**) USB-compliant keyboard: (accel) keeping acceleration scheme 1
(**) USB-compliant keyboard: (accel) filter chain progression: 2.00
(**) USB-compliant keyboard: (accel) filter stage 0: 20.00 ms
(**) USB-compliant keyboard: (accel) set acceleration profile 0
(II) config/hal: Adding input device USB-compliant keyboard
(**) USB-compliant keyboard: always reports core events
(**) USB-compliant keyboard: Device: "/dev/input/event4"
(II) USB-compliant keyboard: Found keys
(II) USB-compliant keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "USB-compliant keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) fglrx(0): EDID vendor "GWY", prod id 2414
(II) fglrx(0): Using hsync ranges from config file
(II) fglrx(0): Using vrefresh ranges from config file
(II) fglrx(0): Printing DDC gathered Modelines:
(II) fglrx(0): Modeline "1920x1200"x0.0  154.00  1920 1968 2000 2080  1200 1203 1209 1235 +hsync -vsync (74.0 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(II) fglrx(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)
(II) fglrx(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz)
(II) fglrx(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) fglrx(0): Modeline "1152x864"x0.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz)
(II) fglrx(0): Modeline "1440x900"x0.0   88.75  1440 1488 1520 1600  900 903 909 926 +hsync -vsync (55.5 kHz)
(II) fglrx(0): Modeline "1440x900"x0.0  136.75  1440 1536 1688 1936  900 903 909 942 -hsync +vsync (70.6 kHz)
(II) fglrx(0): Modeline "1680x1050"x0.0  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
(II) fglrx(0): EDID vendor "GWY", prod id 2414
(II) fglrx(0): Using hsync ranges from config file
(II) fglrx(0): Using vrefresh ranges from config file
(II) fglrx(0): Printing DDC gathered Modelines:
(II) fglrx(0): Modeline "1920x1200"x0.0  154.00  1920 1968 2000 2080  1200 1203 1209 1235 +hsync -vsync (74.0 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(II) fglrx(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)
(II) fglrx(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz)
(II) fglrx(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) fglrx(0): Modeline "1152x864"x0.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz)
(II) fglrx(0): Modeline "1440x900"x0.0   88.75  1440 1488 1520 1600  900 903 909 926 +hsync -vsync (55.5 kHz)
(II) fglrx(0): Modeline "1440x900"x0.0  136.75  1440 1536 1688 1936  900 903 909 942 -hsync +vsync (70.6 kHz)
(II) fglrx(0): Modeline "1680x1050"x0.0  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
(II) fglrx(0): EDID vendor "GWY", prod id 2414
(II) fglrx(0): Using hsync ranges from config file
(II) fglrx(0): Using vrefresh ranges from config file
(II) fglrx(0): Printing DDC gathered Modelines:
(II) fglrx(0): Modeline "1920x1200"x0.0  154.00  1920 1968 2000 2080  1200 1203 1209 1235 +hsync -vsync (74.0 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(II) fglrx(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)
(II) fglrx(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz)
(II) fglrx(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) fglrx(0): Modeline "1152x864"x0.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz)
(II) fglrx(0): Modeline "1440x900"x0.0   88.75  1440 1488 1520 1600  900 903 909 926 +hsync -vsync (55.5 kHz)
(II) fglrx(0): Modeline "1440x900"x0.0  136.75  1440 1536 1688 1936  900 903 909 942 -hsync +vsync (70.6 kHz)
(II) fglrx(0): Modeline "1680x1050"x0.0  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
(II) fglrx(0): EDID vendor "GWY", prod id 2414
(II) fglrx(0): Using hsync ranges from config file
(II) fglrx(0): Using vrefresh ranges from config file
(II) fglrx(0): Printing DDC gathered Modelines:
(II) fglrx(0): Modeline "1920x1200"x0.0  154.00  1920 1968 2000 2080  1200 1203 1209 1235 +hsync -vsync (74.0 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(II) fglrx(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)
(II) fglrx(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz)
(II) fglrx(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) fglrx(0): Modeline "1152x864"x0.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz)
(II) fglrx(0): Modeline "1440x900"x0.0   88.75  1440 1488 1520 1600  900 903 909 926 +hsync -vsync (55.5 kHz)
(II) fglrx(0): Modeline "1440x900"x0.0  136.75  1440 1536 1688 1936  900 903 909 942 -hsync +vsync (70.6 kHz)
(II) fglrx(0): Modeline "1680x1050"x0.0  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
(II) fglrx(0): EDID vendor "GWY", prod id 2414
(II) fglrx(0): Using hsync ranges from config file
(II) fglrx(0): Using vrefresh ranges from config file
(II) fglrx(0): Printing DDC gathered Modelines:
(II) fglrx(0): Modeline "1920x1200"x0.0  154.00  1920 1968 2000 2080  1200 1203 1209 1235 +hsync -vsync (74.0 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(II) fglrx(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)
(II) fglrx(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz)
(II) fglrx(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) fglrx(0): Modeline "1152x864"x0.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz)
(II) fglrx(0): Modeline "1440x900"x0.0   88.75  1440 1488 1520 1600  900 903 909 926 +hsync -vsync (55.5 kHz)
(II) fglrx(0): Modeline "1440x900"x0.0  136.75  1440 1536 1688 1936  900 903 909 942 -hsync +vsync (70.6 kHz)
(II) fglrx(0): Modeline "1680x1050"x0.0  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
(II) fglrx(0): EDID vendor "GWY", prod id 2414
(II) fglrx(0): Using hsync ranges from config file
(II) fglrx(0): Using vrefresh ranges from config file
(II) fglrx(0): Printing DDC gathered Modelines:
(II) fglrx(0): Modeline "1920x1200"x0.0  154.00  1920 1968 2000 2080  1200 1203 1209 1235 +hsync -vsync (74.0 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(II) fglrx(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)
(II) fglrx(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz)
(II) fglrx(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) fglrx(0): Modeline "1152x864"x0.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz)
(II) fglrx(0): Modeline "1440x900"x0.0   88.75  1440 1488 1520 1600  900 903 909 926 +hsync -vsync (55.5 kHz)
(II) fglrx(0): Modeline "1440x900"x0.0  136.75  1440 1536 1688 1936  900 903 909 942 -hsync +vsync (70.6 kHz)
(II) fglrx(0): Modeline "1680x1050"x0.0  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
(II) fglrx(0): EDID vendor "GWY", prod id 2414
(II) fglrx(0): Using hsync ranges from config file
(II) fglrx(0): Using vrefresh ranges from config file
(II) fglrx(0): Printing DDC gathered Modelines:
(II) fglrx(0): Modeline "1920x1200"x0.0  154.00  1920 1968 2000 2080  1200 1203 1209 1235 +hsync -vsync (74.0 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(II) fglrx(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)
(II) fglrx(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz)
(II) fglrx(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) fglrx(0): Modeline "1152x864"x0.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz)
(II) fglrx(0): Modeline "1440x900"x0.0   88.75  1440 1488 1520 1600  900 903 909 926 +hsync -vsync (55.5 kHz)
(II) fglrx(0): Modeline "1440x900"x0.0  136.75  1440 1536 1688 1936  900 903 909 942 -hsync +vsync (70.6 kHz)
(II) fglrx(0): Modeline "1680x1050"x0.0  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
(II) fglrx(0): EDID vendor "GWY", prod id 2414
(II) fglrx(0): Using hsync ranges from config file
(II) fglrx(0): Using vrefresh ranges from config file
(II) fglrx(0): Printing DDC gathered Modelines:
(II) fglrx(0): Modeline "1920x1200"x0.0  154.00  1920 1968 2000 2080  1200 1203 1209 1235 +hsync -vsync (74.0 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz)
(II) fglrx(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(II) fglrx(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)
(II) fglrx(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz)
(II) fglrx(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
(II) fglrx(0): Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz)
(II) fglrx(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) fglrx(0): Modeline "1152x864"x0.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz)
(II) fglrx(0): Modeline "1440x900"x0.0   88.75  1440 1488 1520 1600  900 903 909 926 +hsync -vsync (55.5 kHz)
(II) fglrx(0): Modeline "1440x900"x0.0  136.75  1440 1536 1688 1936  900 903 909 942 -hsync +vsync (70.6 kHz)
(II) fglrx(0): Modeline "1680x1050"x0.0  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
swlDalGetDisplayIndex:ERROR: The number of Active Displays is 0
swlDalGetDisplayIndex:ERROR: The number of Active Displays is 0
swlDalGetDisplayIndex:ERROR: The number of Active Displays is 0
(II) fglrx(0): atiddxDisplayScreenLoadPalette: numColors: 256

xorg.conf

Section "ServerLayout"
    Identifier     "aticonfig Layout"
    Screen      0  "aticonfig-Screen[0]-0" 0 0
EndSection

Section "Files"
EndSection

Section "Module"
EndSection

Section "Monitor"
    Identifier   "aticonfig-Monitor[0]-0"
    Option        "VendorName" "ATI Proprietary Driver"
    Option        "ModelName" "Generic Autodetecting Monitor"
    Option        "DPMS" "true"
EndSection

Section "Device"
    Identifier  "aticonfig-Device[0]-0"
    Driver      "fglrx"
    Option "DRI" "off"
    BusID       "PCI:3:0:0"
EndSection

Section "Screen"
    Identifier "aticonfig-Screen[0]-0"
    Device     "aticonfig-Device[0]-0"
    Monitor    "aticonfig-Monitor[0]-0"
    DefaultDepth     24
    SubSection "Display"
        Viewport   0 0
        Depth     24
    EndSubSection
EndSection

Section "DRI"
    Mode         0666
EndSection

when I dont have dri turned off, I cant even start X (it just locks my computer up)
any help would be greatly appreciated :-D

darthaxul

Member

Registered: 2008-09-24

Posts: 156

Re: fglrx crash on startup

we just have to wait till the 9.5 ati comes out i dont think the 9.4 one will work

reed9

Member

Registered: 2008-06-12

Posts: 77

Re: fglrx crash on startup

I'm no expert on xorg.conf, but you might need to include LOAD "dri" and maybe LOAD "glx" in your Modules section.  It doesn't look like you had an xorg.conf before using aticonfig?  The Arch ATI wiki suggests you generate one before using aticonfig or use the minimal working example.

cakofony

Member

Registered: 2009-04-14

Posts: 13

Re: fglrx crash on startup

That doesnt help :-(

DonVla

Member

From: Bonn, Germany

Registered: 2007-06-07

Posts: 997

Re: fglrx crash on startup

i guess it's related to the xorg-sever update.
you have to reinstall catalyst-utils.

cakofony

Member

Registered: 2009-04-14

Posts: 13

Re: fglrx crash on startup

from xorg log:

(II) "extmod" will be loaded by default.
(II) "dbe" will be loaded by default.
(II) "glx" will be loaded by default.
(II) "record" will be loaded by default.
(II) "dri" will be loaded by default.
(II) "dri2" will be loaded by default.

I couldnt generate an xorg.conf, there is a problem with the newest version of xorg that doesnt allow it for some reason.

How well does the radeonHD driver work? does it support crossfire?

DonVla

Member

From: Bonn, Germany

Registered: 2007-06-07

Posts: 997

Re: fglrx crash on startup

@cakofony:
xorg-server overwrites this file /usr/lib/xorg/modules/extensions/libdri.so
so you need to reinstall catalyst-utils (from your xorg.conf i guess that you use catalyst).

lrwxrwxrwx 1 root root 10 2009-04-15 19:37 /usr/lib/xorg/modules/extensions/libdri.so -> libdri.ati

that's why it works when you disable dri.

cakofony

Member

Registered: 2009-04-14

Posts: 13

Re: fglrx crash on startup

I tried reinstalling it once, I'm trying both catalyst and the utils package now

cakofony

Member

Registered: 2009-04-14

Posts: 13

Re: fglrx crash on startup

The problem persists :-(

DonVla

Member

From: Bonn, Germany

Registered: 2007-06-07

Posts: 997

Re: fglrx crash on startup

How well does the radeonHD driver work? does it support crossfire?

hahaha
is this even supported under linux ?

DonVla

Member

From: Bonn, Germany

Registered: 2007-06-07

Posts: 997

Re: fglrx crash on startup

The problem persists :-(

hmm,
then i have no idea for now.

ps: another idea - remove "/etc/ati/amdpcsdb" and restart X

Last edited by DonVla (2009-04-15 21:41:36)

cakofony

Member

Registered: 2009-04-14

Posts: 13

Re: fglrx crash on startup

no luck

cakofony

Member

Registered: 2009-04-14

Posts: 13

Re: fglrx crash on startup

I guess I'll just install the open source driver.
how does one uninstall AUR packages?

cakofony

Member

Registered: 2009-04-14

Posts: 13

Re: fglrx crash on startup

Now I'm completely lost, I installed arch on my laptop, and the same thing happens when I start X, I just get a blank screen that I cant leave.  My laptop has an nvidia card.

darthaxul

Member

Registered: 2008-09-24

Posts: 156

Re: fglrx crash on startup

guys I found something more specific. If I remember correctly the xorg version cannot be greater than any driver, or vice versa, because if a new feature is added the other software does not know how to handle it. So we have to wait till ati comes with a new driver that knows how to speak to xorg safely.
xorg 7.1 heck there is 7.4 module requirement