Xorg 1.6 won't start, ext3-fs won't mount, kinit kernel panic.

max.o · 2009-06-17 02:14:24

I've spent several hours today looking through the wiki and previous forum posts, trying to understand what went wrong with my new Arch install. I need some help.

I have an IBM Thinkpad X40. I followed the installation guide, which was quite helpful until we came to X. There my troubles began: X wouldn't start with the config file generated by

Xorg -configure

and patching the xorg.conf as suggested in the official install guide didn't help. Apparently the problem is not (directly) related to the driver: neither the intel nor intel-legacy drivers made any difference I could see.

Starting X without an xorg.conf got me stuck in a non-input-accepting state as described in this forum post: http://bbs.archlinux.org/viewtopic.php?id=73657

Worse, when I had to power-cycle the machine, I'm now unable to boot. I get a lot of lines like:

ata1.00: status: { DRDY ERR }
ata1.00: error: { UNC }
ata1.00: configured for UDMA/100
sd 0:0:0:0: [sda] Unhandled sense code

... ending with:

JDB: Failed to read block at offset 583
JDB: recovery failed
EXT3-fs: error loading journal.
kinit: Unable to mount root fs on device dev(8,4)
kinit: init not found!

So now, before I can hope to make X work, I need to fix this. Can anyone help me get my filesystem back, using the 2009.02 install image on my usb drive? Worst case, I'd have to reinstall the whole thing: no data loss, just inconvenient. Ok, maybe worst case is that my hard drive is dying (ext3.fsck did find quite a few bad blocks during the install). I'm in over my head, anyway.

Thanks... - max

perbh · 2009-06-17 04:09:50

Eeeeek!
I would boot from a live cd and run a fsck on the drive - at least for starters.
Hopefully this will fix the disk, but if it doesn't - hey - a new disk is a no-brainer these days :-)

Come back again when the disk is OK and we'll look at your other problems

max.o · 2009-06-17 05:35:39

The installer image utility wasn't able to mount the root partition... but, when I ran through the install sequence again and overwrote the partition, and then checked it, fsck didn't complain at all. So, I'm going to assume that the problem was in software.

Now I'm back to a fresh base install. How can I make Xorg 1.6 start?

perbh · 2009-06-17 12:23:23

You need to give us the xorg.conf file _and_ the result of 'lspci'.
My guess is that you have not installed the appropriate driver for your graphics adapter.

max.o · 2009-06-17 17:23:03

I've installed the xf86-video-intel-legacy driver package, which seemed to be the appropriate one for my Intel 82852/855GM Integrated Graphics Device, but here's my whole lspci output anyway:

00:00.0 Host bridge: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
00:00.1 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
00:00.3 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
00:02.0 VGA compatible controller: Intel Corporation 82852/855GM Integrated Graphics Device (rev 02)
00:02.1 Display controller: Intel Corporation 82852/855GM Integrated Graphics Device (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 81)
00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 01)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01)
00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 01)
02:00.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 8d)
02:00.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 13)
02:01.0 Ethernet controller: Intel Corporation 82541GI Gigabit Ethernet Controller
02:02.0 Ethernet controller: Atheros Communications Inc. Atheros AR5001X+ Wireless Network Adapter (rev 01)

And here's my xorg.conf as freshly generated by Xorg -configure:

Section "ServerLayout"
    Identifier     "X.org Configured"
    Screen      0  "Screen0" 0 0
    Screen      1  "Screen1" RightOf "Screen0"
    InputDevice    "Mouse0" "CorePointer"
    InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
    ModulePath   "/usr/lib/xorg/modules"
    FontPath     "/usr/share/fonts/misc"
    FontPath     "/usr/share/fonts/100dpi:unscaled"
    FontPath     "/usr/share/fonts/75dpi:unscaled"
    FontPath     "/usr/share/fonts/TTF"
    FontPath     "/usr/share/fonts/Type1"
EndSection

Section "Module"
    Load  "dri2"
    Load  "dbe"
    Load  "dri"
    Load  "glx"
    Load  "extmod"
    Load  "record"
EndSection

Section "InputDevice"
    Identifier  "Keyboard0"
    Driver      "kbd"
EndSection

Section "InputDevice"
    Identifier  "Mouse0"
    Driver      "mouse"
    Option        "Protocol" "auto"
    Option        "Device" "/dev/input/mice"
    Option        "ZAxisMapping" "4 5 6 7"
EndSection

Section "Monitor"
    Identifier   "Monitor0"
    VendorName   "Monitor Vendor"
    ModelName    "Monitor Model"
EndSection

Section "Monitor"
    Identifier   "Monitor1"
    VendorName   "Monitor Vendor"
    ModelName    "Monitor Model"
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
        ### [arg]: arg optional
        #Option     "NoAccel"                # [<bool>]
        #Option     "SWcursor"               # [<bool>]
        #Option     "ColorKey"               # <i>
        #Option     "CacheLines"             # <i>
        #Option     "Dac6Bit"                # [<bool>]
        #Option     "DRI"                    # [<bool>]
        #Option     "NoDDC"                  # [<bool>]
        #Option     "ShowCache"              # [<bool>]
        #Option     "XvMCSurfaces"           # <i>
        #Option     "PageFlip"               # [<bool>]
    Identifier  "Card0"
    Driver      "intel"
    VendorName  "Intel Corporation"
    BoardName   "82852/855GM Integrated Graphics Device"
    BusID       "PCI:0:2:0"
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
        ### [arg]: arg optional
        #Option     "NoAccel"                # [<bool>]
        #Option     "SWcursor"               # [<bool>]
        #Option     "ColorKey"               # <i>
        #Option     "CacheLines"             # <i>
        #Option     "Dac6Bit"                # [<bool>]
        #Option     "DRI"                    # [<bool>]
        #Option     "NoDDC"                  # [<bool>]
        #Option     "ShowCache"              # [<bool>]
        #Option     "XvMCSurfaces"           # <i>
        #Option     "PageFlip"               # [<bool>]
    Identifier  "Card1"
    Driver      "intel"
    VendorName  "Intel Corporation"
    BoardName   "82852/855GM Integrated Graphics Device"
    BusID       "PCI:0:2:1"
EndSection

Section "Screen"
    Identifier "Screen0"
    Device     "Card0"
    Monitor    "Monitor0"
    SubSection "Display"
        Viewport   0 0
        Depth     1
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     4
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     8
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     15
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     16
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     24
    EndSubSection
EndSection

Section "Screen"
    Identifier "Screen1"
    Device     "Card1"
    Monitor    "Monitor1"
    SubSection "Display"
        Viewport   0 0
        Depth     1
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     4
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     8
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     15
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     16
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     24
    EndSubSection
EndSection

And, in case it's helpful, here's /var/log/Xorg.0.log:

This is a pre-release version of the X server from The X.Org Foundation.
It is not supported in any way.
Bugs may be filed in the bugzilla at http://bugs.freedesktop.org/.
Select the "xorg" product for bugs you find in this release.
Before reporting bugs in pre-release versions please check the
latest version in the X.Org Foundation git repository.
See http://wiki.x.org/wiki/GitPage for git access instructions.

X.Org X Server 1.6.1.901 (1.6.2 RC 1)
Release Date: 2009-5-8
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.29-ARCH i686 
Current Operating System: Linux thinkpad 2.6.29-ARCH #1 SMP PREEMPT Wed May 20 07:06:02 UTC 2009 i686
Build Date: 28 May 2009  10:40:05PM
 
    Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Wed Jun 17 10:14:27 2009
(II) Loader magic: 0x1a40
(II) Module ABI versions:
    X.Org ANSI C Emulation: 0.4
    X.Org Video Driver: 5.0
    X.Org XInput driver : 4.0
    X.Org Server Extension : 2.0
(II) Loader running on linux
(--) using VT number 7

(--) PCI:*(0@0:2:0) Intel Corporation 82852/855GM Integrated Graphics Device rev 2, Mem @ 0xe0000000/134217728, 0xd0000000/524288, I/O @ 0x00001800/8
(--) PCI: (0@0:2:1) Intel Corporation 82852/855GM Integrated Graphics Device rev 2, Mem @ 0xe8000000/134217728, 0xd0080000/524288
List of video drivers:
    i810
    intel
    vesa
(II) LoadModule: "i810"
(II) Loading /usr/lib/xorg/modules/drivers//i810_drv.so
(II) Module i810: vendor="X.Org Foundation"
    compiled for 1.6.1, module version = 2.3.2
    Module class: X.Org Video Driver
    ABI class: X.Org Video Driver, version 5.0
(II) LoadModule: "intel"
(II) Loading /usr/lib/xorg/modules/drivers//intel_drv.so
(II) Module intel: vendor="X.Org Foundation"
    compiled for 1.6.1, module version = 2.3.2
    Module class: X.Org Video Driver
    ABI class: X.Org Video Driver, version 5.0
(II) UnloadModule: "intel"
(II) Unloading /usr/lib/xorg/modules/drivers//intel_drv.so
(II) Failed to load module "intel" (already loaded, -1078754760)
(II) LoadModule: "vesa"
(II) Loading /usr/lib/xorg/modules/drivers//vesa_drv.so
(II) Module vesa: vendor="X.Org Foundation"
    compiled for 1.6.0, module version = 2.2.0
    Module class: X.Org Video Driver
    ABI class: X.Org Video Driver, version 5.0
(II) System resource ranges:
    [0] -1    0    0xffffffff - 0xffffffff (0x1) MX[b]
    [1] -1    0    0x000f0000 - 0x000fffff (0x10000) MX[b]
    [2] -1    0    0x000c0000 - 0x000effff (0x30000) MX[b]
    [3] -1    0    0x00000000 - 0x0009ffff (0xa0000) MX[b]
    [4] -1    0    0x0000ffff - 0x0000ffff (0x1) IX[b]
    [5] -1    0    0x00000000 - 0x00000000 (0x1) IX[b]
(II) Primary Device is: PCI 00@00:02:0
(II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
    i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
    E7221 (i915), 915GM, 945G, 945GM, 945GME, 965G, G35, 965Q, 946GZ,
    965GM, 965GME/GLE, G33, Q35, Q33, Intel Integrated Graphics Device
(II) VESA: driver for VESA chipsets: vesa
(++) Using config file: "/root/xorg.conf.new"
(==) ServerLayout "X.org Configured"
(**) |-->Screen "Screen0" (0)
(**) |   |-->Monitor "Monitor0"
(**) |   |-->Device "Card0"
(**) |-->Screen "Screen1" (1)
(**) |   |-->Monitor "Monitor1"
(**) |   |-->Device "Card1"
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Keyboard0"
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/TTF" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/share/fonts/Type1" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/share/fonts/TTF" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/share/fonts/Type1" does not exist.
    Entry deleted from font path.
(**) FontPath set to:
    /usr/share/fonts/misc,
    /usr/share/fonts/100dpi:unscaled,
    /usr/share/fonts/75dpi:unscaled,
    /usr/share/fonts/misc,
    /usr/share/fonts/100dpi:unscaled,
    /usr/share/fonts/75dpi:unscaled,
    built-ins
(**) ModulePath set to "/usr/lib/xorg/modules"
(WW) AllowEmptyInput is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
(WW) Disabling Mouse0
(WW) Disabling Keyboard0
(II) resource ranges after xf86ClaimFixedResources() call:
    [0] -1    0    0xffffffff - 0xffffffff (0x1) MX[b]
    [1] -1    0    0x000f0000 - 0x000fffff (0x10000) MX[b]
    [2] -1    0    0x000c0000 - 0x000effff (0x30000) MX[b]
    [3] -1    0    0x00000000 - 0x0009ffff (0xa0000) MX[b]
    [4] -1    0    0x0000ffff - 0x0000ffff (0x1) IX[b]
    [5] -1    0    0x00000000 - 0x00000000 (0x1) IX[b]
(II) resource ranges after xf86ClaimFixedResources() call:
    [0] -1    0    0xffffffff - 0xffffffff (0x1) MX[b]
    [1] -1    0    0x000f0000 - 0x000fffff (0x10000) MX[b]
    [2] -1    0    0x000c0000 - 0x000effff (0x30000) MX[b]
    [3] -1    0    0x00000000 - 0x0009ffff (0xa0000) MX[b]
    [4] -1    0    0x0000ffff - 0x0000ffff (0x1) IX[b]
    [5] -1    0    0x00000000 - 0x00000000 (0x1) IX[b]
(II) resource ranges after probing:
    [0] -1    0    0xffffffff - 0xffffffff (0x1) MX[b]
    [1] -1    0    0x000f0000 - 0x000fffff (0x10000) MX[b]
    [2] -1    0    0x000c0000 - 0x000effff (0x30000) MX[b]
    [3] -1    0    0x00000000 - 0x0009ffff (0xa0000) MX[b]
    [4] 0    0    0x000a0000 - 0x000affff (0x10000) MS[b]
    [5] 0    0    0x000b0000 - 0x000b7fff (0x8000) MS[b]
    [6] 0    0    0x000b8000 - 0x000bffff (0x8000) MS[b]
    [7] 1    0    0x000a0000 - 0x000affff (0x10000) MS[b]
    [8] 1    0    0x000b0000 - 0x000b7fff (0x8000) MS[b]
    [9] 1    0    0x000b8000 - 0x000bffff (0x8000) MS[b]
    [10] -1    0    0x0000ffff - 0x0000ffff (0x1) IX[b]
    [11] -1    0    0x00000000 - 0x00000000 (0x1) IX[b]
    [12] 0    0    0x000003b0 - 0x000003bb (0xc) IS[b]
    [13] 0    0    0x000003c0 - 0x000003df (0x20) IS[b]
    [14] 1    0    0x000003b0 - 0x000003bb (0xc) IS[b]
    [15] 1    0    0x000003c0 - 0x000003df (0x20) IS[b]
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib/xorg/modules//libint10.so
(II) Module int10: vendor="X.Org Foundation"
    compiled for 1.6.1.901, module version = 1.0.0
    ABI class: X.Org Video Driver, version 5.0
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/lib/xorg/modules//libvbe.so
(II) Module vbe: vendor="X.Org Foundation"
    compiled for 1.6.1.901, module version = 1.1.0
    ABI class: X.Org Video Driver, version 5.0
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Reloading /usr/lib/xorg/modules//libint10.so
(II) intel(0): initializing int10
(II) intel(0): Bad V_BIOS checksum
(II) intel(0): Primary V_BIOS segment is: 0xc000
(II) intel(0): VESA BIOS detected
(II) intel(0): VESA VBE Version 3.0
(II) intel(0): VESA VBE Total Mem: 8000 kB
(II) intel(0): VESA VBE OEM: Intel(r)852GM/852GME/855GM/855GME Graphics Chip Accelerated VGA BIOS
(II) intel(0): VESA VBE OEM Software Rev: 1.0
(II) intel(0): VESA VBE OEM Vendor: Intel Corporation
(II) intel(0): VESA VBE OEM Product: Intel(r)852GM/852GME/855GM/855GME Graphics Controller
(II) intel(0): VESA VBE OEM Product Rev: Hardware Version 0.0
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) intel(0): VESA VBE DDC supported
(II) intel(0): VESA VBE DDC Level none
(II) intel(0): VESA VBE DDC transfer in appr. 0 sec.
(II) intel(0): VESA VBE DDC read failed
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Reloading /usr/lib/xorg/modules//libint10.so
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Reloading /usr/lib/xorg/modules//libvbe.so
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Reloading /usr/lib/xorg/modules//libint10.so
(II) intel(1): initializing int10
(EE) intel(1): Cannot read V_BIOS (3) Function not implemented


Xorg detected your mouse at device /dev/input/mice.
Please check your config if the mouse is still not
operational, as by default Xorg tries to autodetect
the protocol.

Xorg has configured a multihead system, please check your config.

Your xorg.conf file is /root/xorg.conf.new

To test the server, run 'X -config /root/xorg.conf.new'

perbh · 2009-06-18 15:26:01

Just out of curiosity - did you copy /root/xorg.conf.new to /etc/X11/xorg.conf ?

If you did - it looks all good to me ...

It might be an idea to remove completely your 2nd monitor until you have got X to work with _one_.

I have a 82915G/GV/910GL intel graphics controller - and _my_ xorg.conf is as follows:

Section "ServerLayout"
        Identifier     "X.org Configured"
        Screen      0  "Screen0" 0 0
        InputDevice    "Mouse0" "CorePointer"
        InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
        ModulePath   "/usr/lib/xorg/modules"
        FontPath     "/usr/share/fonts/misc"
        FontPath     "/usr/share/fonts/100dpi:unscaled"
        FontPath     "/usr/share/fonts/75dpi:unscaled"
        FontPath     "/usr/share/fonts/TTF"
        FontPath     "/usr/share/fonts/Type1"
        FontPath        "/usr/share/fonts/more-ttf"
EndSection

Section "ServerFlags"
        Option  "AutoAddDevices" "false"
        Option  "AllowEmptyInput" "off"
        Option  "DontZap"       "false"
EndSection

Section "Module"
        Load  "glx"
        Load  "extmod"
        Load  "xtrap"
        Load  "dbe"
        Load  "dri"
        Load  "freetype"
EndSection

Section "InputDevice"
        Identifier  "Keyboard0"
#       Driver      "kbd"
        Driver      "keyboard"
        Option      "CoreKeyboard"
        Option      "XkbRules" "xorg"
        Option      "XkbModel" "latitude"
        Option      "XkbLayout" "us,no"
        Option      "XkbOptions" "grp:shifts_toggle"
EndSection

Section "InputDevice"
        Identifier  "Mouse0"
        Driver      "mouse"
        Option      "Protocol" "auto"
        Option      "Device" "/dev/input/mice"
        Option      "ZAxisMapping" "4 5 6 7"
EndSection

Section "Monitor"
        #DisplaySize      340   270     # mm
        Identifier   "Monitor0"
        VendorName   "SNY"
        ModelName    "SDM-S73"
        HorizSync    28.0 - 65.0
        VertRefresh  57.0 - 75.0
        Option      "DPMS"
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
        ### [arg]: arg optional
        #Option     "NoAccel"                   # [<bool>]
        #Option     "SWcursor"                  # [<bool>]
        #Option     "ColorKey"                  # <i>
        #Option     "CacheLines"                # <i>
        #Option     "Dac6Bit"                   # [<bool>]
        #Option     "DRI"                       # [<bool>]
        #Option     "NoDDC"                     # [<bool>]
        #Option     "ShowCache"                 # [<bool>]
        #Option     "XvMCSurfaces"              # <i>
        #Option     "PageFlip"                  # [<bool>]
        Identifier  "Card0"
        Driver      "intel"
        VendorName  "Intel Corporation"
        BoardName   "82915G/GV/910GL Integrated Graphics Controller"
        BusID       "PCI:0:2:0"
EndSection

Section "Screen"
        Identifier "Screen0"
        Device     "Card0"
        Monitor    "Monitor0"
        DefaultDepth    24
        SubSection "Display"
                Viewport   0 0
                Depth     16
                Modes   "1280x1024"
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     24
                Modes   "1280x1024"
        EndSubSection
EndSection

Last edited by perbh (2009-06-18 15:35:57)

Arch Linux

#1 2009-06-17 02:14:24

Xorg 1.6 won't start, ext3-fs won't mount, kinit kernel panic.

#2 2009-06-17 04:09:50

Re: Xorg 1.6 won't start, ext3-fs won't mount, kinit kernel panic.

#3 2009-06-17 05:35:39

Re: Xorg 1.6 won't start, ext3-fs won't mount, kinit kernel panic.

#4 2009-06-17 12:23:23

Re: Xorg 1.6 won't start, ext3-fs won't mount, kinit kernel panic.

#5 2009-06-17 17:23:03

Re: Xorg 1.6 won't start, ext3-fs won't mount, kinit kernel panic.

#6 2009-06-18 15:26:01

Re: Xorg 1.6 won't start, ext3-fs won't mount, kinit kernel panic.

Board footer