You are not logged in.

#1 2005-01-15 23:08:13

phunni
Member
From: Bristol, UK
Registered: 2003-08-13
Posts: 768

Printer not working

I have an HP Deks Jet 5550 connected via a parallel port and I've installed hpijs via pacman.

I have loaded parport, parport_pc and lp as modules.

When I try to configure the printer via localhost:631 I am sometimes told that the parallel port is busy and sometimes that it's all fine - but it never works.  Any jobs sent just sit there never working.  I have logging set to debug and see no errors

When I run tail /var/log/messages I see nothing about my parallel port at all

Can anyone help me with this?

Offline

#2 2005-01-16 02:24:03

colnago
Member
From: Victoria, BC
Registered: 2004-03-25
Posts: 438

Re: Printer not working

I would check your BIOS settings on your computer.  there are typically three settings for a parallel port and it might be defaulting to the wrong one for your printer.

This is a place to check:

http://www.linuxprinting.org/

Offline

#3 2005-01-16 13:40:25

phunni
Member
From: Bristol, UK
Registered: 2003-08-13
Posts: 768

Re: Printer not working

Checked the BIOS and there didn't seem to be any obvious settings for a printer or parallel port...

Offline

#4 2005-01-16 15:00:06

Mr Green
Forum Fellow
From: U.K.
Registered: 2003-12-21
Posts: 5,893
Website

Re: Printer not working

try just parport-lp & lp .....


Mr Green

Offline

#5 2005-01-16 17:29:52

phunni
Member
From: Bristol, UK
Registered: 2003-08-13
Posts: 768

Re: Printer not working

parport-lp not found.  I'm using the stock 2.6.10 kernel

Offline

#6 2005-01-16 17:56:50

Mr Green
Forum Fellow
From: U.K.
Registered: 2003-12-21
Posts: 5,893
Website

Re: Printer not working

oops parport_lp  wink


Mr Green

Offline

#7 2005-01-16 18:22:02

phunni
Member
From: Bristol, UK
Registered: 2003-08-13
Posts: 768

Re: Printer not working

smile I tried both and they're still not found.  Generally, I think, if you enter a hyphen it reads it as an underscore anyway...

Offline

#8 2005-01-16 18:39:08

Mr Green
Forum Fellow
From: U.K.
Registered: 2003-12-21
Posts: 5,893
Website

Re: Printer not working

what does

dmesg | grep lp

give you ?


Mr Green

Offline

#9 2005-01-16 19:24:40

phunni
Member
From: Bristol, UK
Registered: 2003-08-13
Posts: 768

Re: Printer not working

nothing...

Offline

#10 2005-01-16 19:31:24

Mr Green
Forum Fellow
From: U.K.
Registered: 2003-12-21
Posts: 5,893
Website

Re: Printer not working

Then it could be that your bios is not set up ....

I get

lp: driver loaded but no devices found
lp0: using parport0 (polling).

Mr Green

Offline

#11 2005-01-16 19:44:25

phunni
Member
From: Bristol, UK
Registered: 2003-08-13
Posts: 768

Re: Printer not working

Changed the bios (spent ages looking this time) and I now get

 lp0: using parport0 (polling)

when i do

dmesg | grep lp

But I still get the same problem - and still nothing in the logs.  The cups config page says that the parallel port is busy...

Offline

#12 2005-01-16 20:29:24

Mr Green
Forum Fellow
From: U.K.
Registered: 2003-12-21
Posts: 5,893
Website

Re: Printer not working

I assume you have followed this ;

http://wiki2.archlinux.org/index.php/CUPS%20setup


Mr Green

Offline

#13 2005-01-16 21:12:58

phunni
Member
From: Bristol, UK
Registered: 2003-08-13
Posts: 768

Re: Printer not working

yes I did...

Offline

#14 2005-01-16 21:43:30

phunni
Member
From: Bristol, UK
Registered: 2003-08-13
Posts: 768

Re: Printer not working

now it says

lp0: using parport0 (interrupt-driven)

Offline

#15 2005-01-17 08:01:56

Mr Green
Forum Fellow
From: U.K.
Registered: 2003-12-21
Posts: 5,893
Website

Re: Printer not working

http://www.google.co.uk/linux?q=cache:R … 5550&hl=en

shows that your printer is supported

do you Kde or Gnome  ? if so try to see if printer is shown

CUPS is a pain to set up (I had problems myself)

stick with it  wink


Mr Green

Offline

#16 2005-01-17 20:11:41

phunni
Member
From: Bristol, UK
Registered: 2003-08-13
Posts: 768

Re: Printer not working

I'm not using X as this is for a server which will share the printer - so I'm using the browser interface from my desktop.  Don't worry, i will stick at it - I need this printer!  big_smile

Offline

#17 2005-01-26 20:57:12

phunni
Member
From: Bristol, UK
Registered: 2003-08-13
Posts: 768

Re: Printer not working

I'm not making any progress on this.  I have no clear error messages.  WhenI go into bios my printer wakes up, so it seems like all is connected ok.  I set the parallel port to ECP+EPP since that seemed to give the best results - but nothing actually works.  Can anyone suggest anything useful I might try? I have no printer...

Offline

#18 2005-01-27 19:21:00

phunni
Member
From: Bristol, UK
Registered: 2003-08-13
Posts: 768

Re: Printer not working

To give a little more info.  Whenever I try and start a job, the status changes from "idle, accepting jobs" to "parallel port is busy, wil lrety in 30 seconds"

Not sure if that's relevant or not...

Offline

#19 2005-10-28 02:17:04

DarkMind
Member
Registered: 2005-02-22
Posts: 68

Re: Printer not working

phunni wrote:

now it says

lp0: using parport0 (interrupt-driven)

same problem here  :?


i have a epson stylus color 600

Offline

Board footer

Powered by FluxBB