Serious problem on USB "hotplug"

capolise · 2008-08-28 07:42:42

I recently installed ArchLinux by the official guide and I have the default configuration for kernel and udev rules.

This is what I get: if I boot arch with my usb mouse or usb stick already plugged they work correctly, but if I "hot-plug" them they aren't recognized and I get some messagges like this,(even if in some case I can "hot-plug" my usb stick!):

[...]
usb 1-1: reset high speed USB device using ehci_hcd and address 2
usb 1-1: device not accepting address 2, error -110
usb 1-1: reset high speed USB device using ehci_hcd and address 2
usb 1-1: device not accepting address 2, error -110
[...]
usb 1-1: new high speed USB device using ehci_hcd and address 3
usb 1-1: device not accepting address 3, error -110
usb 1-1: new high speed USB device using ehci_hcd and address 4
usb 1-1: device not accepting address 4, error -110
[...]

This is the complete dmesg log:

Linux version 2.6.26-ARCH (root@T-POWA-LX) (gcc version 4.3.1 20080724 (prerelease) (GCC) ) #1 SMP PREEMPT Sun Aug 10 12:29:20 UTC 2008
PAT disabled. Not yet verified on this CPU type.
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
 BIOS-e820: 000000003fff0000 - 000000003fffffc0 (ACPI data)
 BIOS-e820: 000000003fffffc0 - 0000000040000000 (ACPI NVS)
 BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
Entering add_active_range(0, 0, 262128) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   229376
  HighMem    229376 ->   262128
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->   262128
On node 0 totalpages: 262128
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 256 pages used for memmap
  HighMem zone: 32496 pages, LIFO batch:7
  Movable zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000E6010, 0014 (r0 OID_00)
ACPI: RSDT 3FFFB9B6, 0034 (r1 INSYDE RSDT_000        1 _CSI    10101)
ACPI: FACP 3FFFFB00, 0074 (r1 TOSINV FACP_000      100 _CSI    10101)
ACPI: DSDT 3FFFBC50, 3EA5 (r1 INSYDE    Intel     1004 INTL  2002036)
ACPI: FACS 3FFFFFC0, 0040
ACPI: BOOT 3FFFFB90, 0028 (r1 INSYDE SYS_BOOT      100 _CSI    10101)
ACPI: DBGP 3FFFFBC0, 0034 (r1 INSYDE DBGP_000      100 _CSI    10101)
ACPI: SSDT 3FFFB9EA, 0190 (r1 INSYDE   GV3Ref     1001 INTL  2012044)
ACPI: PM-Timer IO Port: 0x1008
Allocating PCI resources starting at 50000000 (gap: 40000000:bfb80000)
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
SMP: Allowing 0 CPUs, 0 hotplug CPUs
PERCPU: Allocating 39464 bytes of per cpu data
NR_CPUS: 16, nr_cpu_ids: 1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260080
Kernel command line: root=/dev/sda7 ro 5
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffb000 (01810000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1694.566 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1034080k/1048512k available (2105k kernel code, 13724k reserved, 738k data, 264k init, 131008k highmem)
virtual kernel memory layout:
    fixmap  : 0xffee4000 - 0xfffff000   (1132 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc03cd000 - 0xc040f000   ( 264 kB)
      .data : 0xc030e78e - 0xc03c7380   ( 738 kB)
      .text : 0xc0100000 - 0xc030e78e   (2105 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 3392.05 BogoMIPS (lpj=5651285)
Security Framework initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 9k freed
ACPI: Core revision 20080321
ACPI: Checking initramfs for custom DSDT
ACPI: setting ELCR to 0200 (from 0c80)
weird, boot CPU (#0) not listedby the BIOS.
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
SMP disabled
Brought up 1 CPUs
Total of 1 processors activated (3392.05 BogoMIPS).
net_namespace: 652 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xe94d4, last bus=2
PCI: Using configuration type 1 for base access
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: EC: GPE storm detected, disabling EC GPE
ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in poll mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 1300-133f claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 5 6 *10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 6) *10
ACPI: PCI Interrupt Link [LNKC] (IRQs 5 6 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 6 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 5 6 *10 11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 5 *7 10 11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 5 6 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 5 6 10 11) *0, disabled.
ACPI: Power Resource [PUT2] (on)
ACPI: Power Resource [PFA1] (off)
ACPI: Power Resource [PFA0] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
ACPI: RTC can wake from S4
system 00:05: iomem range 0xfff80000-0xffffffff could not be reserved
system 00:05: iomem range 0xd0000-0xd0eff has been reserved
system 00:07: ioport range 0x680-0x6ff has been reserved
system 00:07: ioport range 0x200-0x20f has been reserved
system 00:07: ioport range 0x300-0x301 has been reserved
system 00:07: ioport range 0x310-0x31f has been reserved
system 00:07: ioport range 0x320-0x321 has been reserved
system 00:07: ioport range 0x1000-0x107f has been reserved
system 00:07: ioport range 0x1300-0x133f has been reserved
system 00:07: ioport range 0x77c-0x77f has been reserved
system 00:07: ioport range 0x800-0x80f has been reserved
PCI: Bridge: 0000:00:01.0
  IO window: c000-dfff
  MEM window: 0xe0000000-0xefffffff
  PREFETCH window: 0x00000000a0000000-0x00000000afffffff
PCI: Bus 3, cardbus bridge: 0000:02:09.0
  IO window: 0x0000a400-0x0000a4ff
  IO window: 0x0000a800-0x0000a8ff
  PREFETCH window: 0x90000000-0x93ffffff
  MEM window: 0xd4000000-0xd7ffffff
PCI: Bridge: 0000:00:1e.0
  IO window: a000-bfff
  MEM window: 0xd0000000-0xdfffffff
  PREFETCH window: 0x0000000090000000-0x000000009fffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs... done
Freeing initrd memory: 650k freed
Simple Boot Flag at 0x37 set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1765
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:00.0: Boot video device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 6
PCI: setting IRQ 6 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.6[b] -> Link [LNKB] -> GSI 6 (level, low) -> IRQ 6
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
input: Macintosh mouse button emulation as /class/input/input0
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 264k freed
No dock devices found.
input: AT Translated Set 2 keyboard as /class/input/input1
SCSI subsystem initialized
libata version 3.00 loaded.
pata_acpi 0000:00:1f.1: enabling device (0005 -> 0007)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1f.1 to 64
ACPI: PCI interrupt for device 0000:00:1f.1 disabled
ata_piix 0000:00:1f.1: version 2.12
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1f.1 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1100 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1108 irq 15
Switched to high resolution mode on CPU 0
ata1.00: ATA-6: HTS548060M9AT00, MGBOA53A, max UDMA/100
ata1.00: 117210240 sectors, multi 16: LBA48 
ata1.00: configured for UDMA/100
ata2.00: ATAPI: MATSHITADVD-RAM UJ-840S, 1.50, max UDMA/33
ata2.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access     ATA      HTS548060M9AT00  MGBO PQ: 0 ANSI: 5
scsi 1:0:0:0: CD-ROM            MATSHITA DVD-RAM UJ-840S  1.50 PQ: 0 ANSI: 5
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 11, io mem 0xf4000000
USB Universal Host Controller Interface driver v3.0
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 < sda5 sda6 sda7 sda8<6>ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 10, io base 0x00001200
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
 sda9 >
sd 0:0:0:0: [sda] Attached SCSI disk
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.1[b] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001220
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001240
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-1: new high speed USB device using ehci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
8139cp 0000:02:07.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp 0000:02:07.0: Try the "8139too" driver instead.
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [LNKF] -> GSI 7 (level, low) -> IRQ 7
eth0: RealTek RTL8139 at 0xf8870300, 00:03:9d:75:6c:92, IRQ 7
eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: ACPI0007:00 is registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
Marking TSC unstable due to: TSC halts in idle.
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
ipw2200: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNKB] -> GSI 6 (level, low) -> IRQ 6
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
firmware: requesting ipw2200-bss.fw
ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
ACPI: PCI Interrupt 0000:00:1f.5[b] -> Link [LNKB] -> GSI 6 (level, low) -> IRQ 6
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 52784 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:00:1f.6[b] -> Link [LNKB] -> GSI 6 (level, low) -> IRQ 6
PCI: Setting latency timer of device 0000:00:1f.6 to 64
MC'97 1 converters and GPIO not ready (0xf000)
vboxdrv: Trying to deactivate the NMI watchdog permanently...
vboxdrv: Successfully done.
vboxdrv: Found 1 processor cores.
vboxdrv: fAsync=0 u64DiffCores=1.
vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
vboxdrv: Successfully loaded version 1.6.4 (interface 0x00080000).
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Sleep Button (CM) as /class/input/input3
ACPI: Sleep Button (CM) [SLPB]
input: Lid Switch as /class/input/input4
ACPI: Lid Switch [LID]
input: Power Button (CM) as /class/input/input5
ACPI: Power Button (CM) [PBTN]
ACPI: Transitioning device [FAN0] to D3
ACPI: PNP0C0B:00 is registered as cooling_device1
ACPI: Fan [FAN0] (off)
ACPI: Transitioning device [FAN1] to D3
ACPI: PNP0C0B:01 is registered as cooling_device2
ACPI: Fan [FAN1] (off)
ACPI: LNXTHERM:01 is registered as thermal_zone0
ACPI: Thermal Zone [THZN] (40 C)
ACPI: LNXTHERM:02 is registered as thermal_zone1
ACPI: Thermal Zone [THZV] (29 C)
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Linux agpgart interface v0.103
agpgart: Detected an Intel 855PM Chipset.
agpgart: AGP aperture is 64M @ 0xb0000000
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
intel_rng: FWH not detected
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
Yenta: CardBus bridge found at 0000:02:09.0 [17ff:5005]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:09.0, mfunc 0x01aa1b22, devctl 0x66
input: PC Speaker as /class/input/input6
Yenta: ISA IRQ mask 0x0038, PCI irq 10
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#02) from #02 to #06
pcmcia: parent PCI bridge I/O window: 0xa000 - 0xbfff
cs: IO port probe 0xa000-0xbfff: clean.
pcmcia: parent PCI bridge Memory window: 0xd0000000 - 0xdfffffff
pcmcia: parent PCI bridge Memory window: 0x90000000 - 0x9fffffff
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 10
ACPI: PCI Interrupt 0000:02:09.3[D] -> Link [LNKG] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
ACPI: PCI Interrupt 0000:02:09.2[C] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10]  MMIO=[febff800-febfffff]  Max Packet=[2048]  IR/IT contexts=[4/8]
NET: Registered protocol family 23
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x926eb1, caps: 0x804719/0x0
input: SynPS/2 Synaptics TouchPad as /class/input/input7
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
irq 11: nobody cared (try booting with the "irqpoll" option)
Pid: 6, comm: events/0 Not tainted 2.6.26-ARCH #1
 [<c015a764>] __report_bad_irq+0x24/0x90
 [<c015aa52>] note_interrupt+0x282/0x2c0
 [<c0159e70>] handle_IRQ_event+0x30/0x60
 [<c015b2c3>] handle_level_irq+0xd3/0x100
 [<c010712b>] do_IRQ+0x3b/0x70
 [<c01049c7>] common_interrupt+0x23/0x28
 [<c0159e57>] handle_IRQ_event+0x17/0x60
 [<c015b26d>] handle_level_irq+0x7d/0x100
 [<c010712b>] do_IRQ+0x3b/0x70
 [<f8add1be>] csr1212_generate_csr_image+0x51e/0x7a0 [ieee1394]
 [<f8ac59bc>] set_phy_reg+0x1c/0xc0 [ohci1394]
 [<c01049c7>] common_interrupt+0x23/0x28
 [<f8ad301b>] hpsb_reset_bus+0x1b/0x20 [ieee1394]
 [<c013ba14>] run_workqueue+0x74/0x130
 [<f8ad5660>] delayed_reset_bus+0x0/0xd0 [ieee1394]
 [<c013bb50>] worker_thread+0x80/0xf0
 [<c013f430>] autoremove_wake_function+0x0/0x50
 [<c013bad0>] worker_thread+0x0/0xf0
 [<c013f149>] kthread+0x39/0x70
 [<c013f110>] kthread+0x0/0x70
 [<c0104c23>] kernel_thread_helper+0x7/0x14
 =======================
handlers:
[<f88ac490>] (usb_hcd_irq+0x0/0x80 [usbcore])
[<f88ac490>] (usb_hcd_irq+0x0/0x80 [usbcore])
[<f88ac490>] (usb_hcd_irq+0x0/0x80 [usbcore])
Disabling IRQ #11
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00039d039d756c92]
EXT3 FS on sda7, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
fuse init (API version 7.9)
Adding 1108444k swap on /dev/sda5.  Priority:-1 extents:1 across:1108444k
scsi 2:0:0:0: Direct-Access     DIKOM    USB Flash Drive  0.00 PQ: 0 ANSI: 2
sd 2:0:0:0: [sdb] 2015231 512-byte hardware sectors (1032 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 00 00 00
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] 2015231 512-byte hardware sectors (1032 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 00 00 00
sd 2:0:0:0: [sdb] Assuming drive cache: write through
 sdb: sdb1
sd 2:0:0:0: [sdb] Attached SCSI removable disk
sd 2:0:0:0: Attached scsi generic sg2 type 0
usb-storage: device scan complete
Clocksource tsc unstable (delta = -141483503 ns)
eth0: link down
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
[drm] Initialized radeon 1.29.0 20080528 on minor 0
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[drm] Setting GART location based on new memory map
[drm] Loading R300 Microcode
[drm] Num pipes: 1
[drm] writeback test succeeded in 2 usecs
usb 1-1: reset high speed USB device using ehci_hcd and address 2
usb 1-1: device not accepting address 2, error -110
usb 1-1: reset high speed USB device using ehci_hcd and address 2
usb 1-1: device not accepting address 2, error -110
usb 1-1: reset high speed USB device using ehci_hcd and address 2
usb 1-1: device not accepting address 2, error -110
usb 1-1: reset high speed USB device using ehci_hcd and address 2
usb 1-1: device not accepting address 2, error -110
usb 1-1: USB disconnect, address 2
sd 2:0:0:0: Device offlined - not ready after error recovery
sd 2:0:0:0: [sdb] READ CAPACITY failed
sd 2:0:0:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00
sd 2:0:0:0: [sdb] Sense not available.
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 00 00 00
sd 2:0:0:0: [sdb] Assuming drive cache: write through
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: [sdb] READ CAPACITY failed
scsi 2:0:0:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00
scsi 2:0:0:0: [sdb] Sense not available.
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: [sdb] Write Protect is off
scsi 2:0:0:0: [sdb] Mode Sense: 00 00 00 00
scsi 2:0:0:0: [sdb] Assuming drive cache: write through
usb 1-1: new high speed USB device using ehci_hcd and address 3
usb 1-1: device not accepting address 3, error -110
usb 1-1: new high speed USB device using ehci_hcd and address 4
usb 1-1: device not accepting address 4, error -110
usb 1-1: new high speed USB device using ehci_hcd and address 5
usb 1-1: device not accepting address 5, error -110
usb 1-1: new high speed USB device using ehci_hcd and address 6
usb 1-1: device not accepting address 6, error -110
hub 1-0:1.0: unable to enumerate USB device on port 1
usb 2-1: new full speed USB device using uhci_hcd and address 2
usb 2-1: not running at top speed; connect to a high speed hub
usb 2-1: configuration #1 chosen from 1 choice
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi 3:0:0:0: Direct-Access     DIKOM    USB Flash Drive  0.00 PQ: 0 ANSI: 2
sd 3:0:0:0: [sdb] 2015231 512-byte hardware sectors (1032 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 00 00 00
sd 3:0:0:0: [sdb] Assuming drive cache: write through
sd 3:0:0:0: [sdb] 2015231 512-byte hardware sectors (1032 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 00 00 00
sd 3:0:0:0: [sdb] Assuming drive cache: write through
 sdb: sdb1
sd 3:0:0:0: [sdb] Attached SCSI removable disk
sd 3:0:0:0: Attached scsi generic sg2 type 0
usb-storage: device scan complete
atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xee on isa0060/serio0).
atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[drm] Num pipes: 1
mtrr: no MTRR for a8000000,4000000 found
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[drm] Setting GART location based on new memory map
[drm] Loading R300 Microcode
[drm] Num pipes: 1
[drm] writeback test succeeded in 2 usecs

Last edited by capolise (2008-09-12 08:46:23)

Devastator · 2008-08-29 08:04:07

So I am not the only one who has such a problem...

In my case even the sdb devices did not show up (as they used to before). May it be some kernel issue? I did a kernel upgrade to 2.26.6-3, so it's not a problem that some encountered with 2.26-6-2...

Also - when booting with my Wacom tablet it works perfectly, bot when I hotplug it, the it is incorrectly recognised, and behaves more like a mouse (also I cannot change it's behaviour by wacomcpl)

Last edited by Devastator (2008-08-29 08:06:46)

tigrmesh · 2008-08-29 17:13:54

Arch doesn't use hotplug, it uses udev. Maybe /etc/udev/readme-udev-arch.txt will give some hints.

Devastator · 2008-08-29 18:45:24

True, sorry for my english then - I meant that I plug it when I am logged into system.

I'll try to find a solution there (I am looking for it for a week, without a result ). If I did not succeed, Ill ask again with more precise data . Thanks!

Last edited by Devastator (2008-08-29 18:47:19)

capolise · 2008-09-05 19:23:33

The problem for me seems to be solved with the last kernel upgrade: kernel26-2.6.26.3-1

capolise · 2008-09-12 08:45:47

I resume this thread because the problem is not really solved...

I have noticed that unloading uhci-hcd module and the reloading it the mouse works! I also noticed that I have the ehci-hcd module loaded and I believe that it is useless because uhci-hcd and ehci-hcd are mutually exclusive.

How can I avoid at boot time the loading of ehci-hcd module?

bagheera · 2009-12-05 11:51:55

Hi, i have the same problem here. I recently installed arch on my msi wind netbook, how it was described on wiki. System is running fine (i still have some issues left), but i can't hot-plug ANY USB device, mice, flashdrive..

If i plug it before i turn pc on, they are detected. But if i remount the plug, it doesn't work

I DON"T use any xorg.conf file, since i couldn't configure it properly

Here's my rc.conf:

#
# /etc/rc.conf - Main Configuration for Arch Linux
#

# -----------------------------------------------------------------------
# LOCALIZATION
# -----------------------------------------------------------------------
#
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
#
LOCALE="pl_PL.UTF-8"
HARDWARECLOCK="UTC"
USEDIRECTISA="no"
TIMEZONE="Europe/Warsaw"
KEYMAP="pl"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"

# -----------------------------------------------------------------------
# HARDWARE
# -----------------------------------------------------------------------
#
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
#
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
#
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=(uvcvideo acpi_cpufreq cpufreq_ondemand cpufreq_powersave)

# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"

# -----------------------------------------------------------------------
# NETWORKING
# -----------------------------------------------------------------------
#
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
#
HOSTNAME="msi"

# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
#
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
#   - prefix an entry in INTERFACES with a ! to disable it
#   - no hyphens in your interface names - Bash doesn't like it
# 
# DHCP:     Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
#

#Static IP example
#eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
#eth0="dhcp"
INTERFACES=(eth0)

# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
#   - prefix an entry in ROUTES with a ! to disable it
#
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
 
# Enable these network profiles at boot-up.  These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
#   - set to 'menu' to present a menu during boot-up (dialog package required)
#   - prefix an entry with a ! to disable it
#
# Network profiles are found in /etc/network.d
#
# This now requires the netcfg package
#
#NETWORKS=(main)

# -----------------------------------------------------------------------
# DAEMONS
# -----------------------------------------------------------------------
#
# Daemons to start at boot-up (in this order)
#   - prefix a daemon with a ! to disable it
#   - prefix a daemon with a @ to start it up in the background
#
DAEMONS=(syslog-ng hal !network !netfs dbus bluetooth crond alsa wicd kdm)

and dmesg

Linux version 2.6.31-ARCH (root@architect) (gcc version 4.4.2 (GCC) ) #1 SMP PREEMPT Tue Nov 10 19:48:17 CET 2009
KERNEL supported cpus:
  Intel GenuineIntel
  AMD AuthenticAMD
  NSC Geode by NSC
  Cyrix CyrixInstead
  Centaur CentaurHauls
  Transmeta GenuineTMx86
  Transmeta TransmetaCPU
  UMC UMC UMC UMC
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)
 BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003f5b2000 (usable)
 BIOS-e820: 000000003f5b2000 - 000000003f5d5000 (ACPI NVS)
 BIOS-e820: 000000003f5d5000 - 000000003f5e6000 (reserved)
 BIOS-e820: 000000003f5e6000 - 000000003f5e9000 (ACPI NVS)
 BIOS-e820: 000000003f5e9000 - 000000003f605000 (reserved)
 BIOS-e820: 000000003f605000 - 000000003f606000 (ACPI NVS)
 BIOS-e820: 000000003f606000 - 000000003f608000 (reserved)
 BIOS-e820: 000000003f608000 - 000000003f611000 (ACPI data)
 BIOS-e820: 000000003f611000 - 000000003f617000 (ACPI NVS)
 BIOS-e820: 000000003f617000 - 000000003f700000 (reserved)
 BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved)
 BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
DMI 2.4 present.
AMI BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
last_pfn = 0x3f5b2 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
  00000-9FFFF write-back
  A0000-BFFFF uncachable
  C0000-DBFFF write-protect
  DC000-E7FFF write-through
  E8000-FFFFF write-protect
MTRR variable ranges enabled:
  0 base 000000000 mask 0C0000000 write-back
  1 base 03F700000 mask 0FFF00000 uncachable
  2 base 03F800000 mask 0FF800000 uncachable
  3 disabled
  4 disabled
  5 disabled
  6 disabled
  7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Scanning 0 areas for low memory corruption
modified physical RAM map:
 modified: 0000000000000000 - 0000000000010000 (reserved)
 modified: 0000000000010000 - 000000000009ec00 (usable)
 modified: 000000000009ec00 - 00000000000a0000 (reserved)
 modified: 00000000000e0000 - 0000000000100000 (reserved)
 modified: 0000000000100000 - 000000003f5b2000 (usable)
 modified: 000000003f5b2000 - 000000003f5d5000 (ACPI NVS)
 modified: 000000003f5d5000 - 000000003f5e6000 (reserved)
 modified: 000000003f5e6000 - 000000003f5e9000 (ACPI NVS)
 modified: 000000003f5e9000 - 000000003f605000 (reserved)
 modified: 000000003f605000 - 000000003f606000 (ACPI NVS)
 modified: 000000003f606000 - 000000003f608000 (reserved)
 modified: 000000003f608000 - 000000003f611000 (ACPI data)
 modified: 000000003f611000 - 000000003f617000 (ACPI NVS)
 modified: 000000003f617000 - 000000003f700000 (reserved)
 modified: 00000000ffb00000 - 00000000ffc00000 (reserved)
 modified: 00000000fff00000 - 0000000100000000 (reserved)
initial memory mapped : 0 - 01800000
init_memory_mapping: 0000000000000000-00000000377fe000
 0000000000 - 0000400000 page 4k
 0000400000 - 0037400000 page 2M
 0037400000 - 00377fe000 page 4k
kernel direct mapping tables up to 377fe000 @ 10000-15000
RAMDISK: 3f4f7000 - 3f5a18c3
Allocated new RAMDISK: 00100000 - 001aa8c3
Move RAMDISK from 000000003f4f7000 - 000000003f5a18c2 to 00100000 - 001aa8c2
ACPI: RSDP 000f03c0 00024 (v02 MSI_NB)
ACPI: XSDT 3f60ff10 0005C (v01 MSI_NB MEGABOOK 06222004 MSFT 00010013)
ACPI: FACP 3f5e6c10 000F4 (v04 MSI_NB MEGABOOK 06222004 MSFT 00010013)
ACPI Warning: 32/64 FACS address mismatch in FADT - two FACS tables! 20090521 tbfadt-370
ACPI Warning: 32/64X FACS address mismatch in FADT - 3F611E40/000000003F611D40, using 32 20090521 tbfadt-487
ACPI: DSDT 3f608010 053CA (v01 MSI_NB MEGABOOK 00000000 INTL 20051117)
ACPI: FACS 3f611e40 00040
ACPI: APIC 3f610e90 0005C (v02 MSI_NB MEGABOOK 06222004 MSFT 00010013)
ACPI: MCFG 3f615c90 0003C (v01 MSI_NB MEGABOOK 06222004 MSFT 00000097)
ACPI: SLIC 3f612c10 00176 (v01 MSI_NB MEGABOOK 06222004 MSFT 00000097)
ACPI: SSDT 3f605510 004CE (v02  PmRef    CpuPm 00003000 INTL 20051117)
ACPI: SSDT 3f5e8a10 00232 (v02  PmRef  Cpu0Tst 00003000 INTL 20051117)
ACPI: SSDT 3f611a10 000A0 (v02  PmRef  Cpu1Tst 00003000 INTL 20051117)
ACPI: Local APIC address 0xfee00000
125MB HIGHMEM available.
887MB LOWMEM available.
  mapped low ram: 0 - 377fe000
  low ram: 0 - 377fe000
  node 0 low ram: 00000000 - 377fe000
  node 0 bootmap 00011000 - 00017f00
(9 early reservations) ==> bootmem [0000000000 - 00377fe000]
  #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
  #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
  #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
  #3 [0001000000 - 000156da44]    TEXT DATA BSS ==> [0001000000 - 000156da44]
  #4 [000009ec00 - 0000100000]    BIOS reserved ==> [000009ec00 - 0000100000]
  #5 [000156e000 - 00015741cc]              BRK ==> [000156e000 - 00015741cc]
  #6 [0000010000 - 0000011000]          PGTABLE ==> [0000010000 - 0000011000]
  #7 [0000100000 - 00001aa8c3]      NEW RAMDISK ==> [0000100000 - 00001aa8c3]
  #8 [0000011000 - 0000018000]          BOOTMAP ==> [0000011000 - 0000018000]
Zone PFN ranges:
  DMA      0x00000010 -> 0x00001000
  Normal   0x00001000 -> 0x000377fe
  HighMem  0x000377fe -> 0x0003f5b2
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0: 0x00000010 -> 0x0000009e
    0: 0x00000100 -> 0x0003f5b2
On node 0 totalpages: 259392
free_area_init_node: node 0, pgdat c141b740, node_mem_map c1575200
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 3950 pages, LIFO batch:0
  Normal zone: 1744 pages used for memmap
  Normal zone: 221486 pages, LIFO batch:31
  HighMem zone: 252 pages used for memmap
  HighMem zone: 31928 pages, LIFO batch:7
Using APIC driver default
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009e000 - 000000000009f000
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at 3f700000 (gap: 3f700000:c0400000)
NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 14 pages at c1d69000, static data 34332 bytes
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 257364
Kernel command line: root=/dev/disk/by-uuid/449d4148-107b-46b9-8930-4134f9a4b57f ro
PID hash table entries: 4096 (order: 12, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Initializing HighMem for node 0 (000377fe:0003f5b2)
Memory: 1021876k/1038024k available (3111k kernel code, 15340k reserved, 1120k data, 416k init, 128720k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff1e000 - 0xfffff000   ( 900 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf7ffe000 - 0xff7fe000   ( 120 MB)
    lowmem  : 0xc0000000 - 0xf77fe000   ( 887 MB)
      .init : 0xc1422000 - 0xc148a000   ( 416 kB)
      .data : 0xc1309ddd - 0xc1421ea8   (1120 kB)
      .text : 0xc1000000 - 0xc1309ddd   (3111 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
NR_IRQS:512
Extended CMOS year: 2000
Fast TSC calibration using PIT
Detected 1599.933 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
spurious 8259A interrupt: IRQ7.
Calibrating delay loop (skipped), value calculated using timer frequency.. 3201.19 BogoMIPS (lpj=5333110)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 24K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 5 MCE banks
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
Performance Counters: Atom events, Intel PMU driver.
... version:                 3
... bit width:               40
... generic counters:        2
... value mask:              000000ffffffffff
... max period:              000000007fffffff
... fixed-purpose counters:  3
... counter mask:            0000000700000003
Checking 'hlt' instruction... OK.
ACPI: Core revision 20090521
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
CPU0: Intel(R) Atom(TM) CPU N270   @ 1.60GHz stepping 02
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3201.04 BogoMIPS (lpj=5332870)
CPU: L1 I cache: 32K, L1 D cache: 24K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 5 MCE banks
CPU1: Thermal monitoring enabled (TM2)
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Atom(TM) CPU N270   @ 1.60GHz stepping 02
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (6402.23 BogoMIPS).
CPU0 attaching sched-domain:
 domain 0: span 0-1 level SIBLING
  groups: 0 1
CPU1 attaching sched-domain:
 domain 0: span 0-1 level SIBLING
  groups: 1 0
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: Not using MMCONFIG.
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: BIOS _OSI(Linux) query ignored
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
PCI: Using MMCONFIG for extended config space
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: EC: GPE storm detected, transactions will use polling mode
ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in poll mode
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:02.0: reg 10 32bit mmio: [0xdfe80000-0xdfefffff]
pci 0000:00:02.0: reg 14 io port: [0xd100-0xd107]
pci 0000:00:02.0: reg 18 32bit mmio: [0xc0000000-0xcfffffff]
pci 0000:00:02.0: reg 1c 32bit mmio: [0xdff00000-0xdff3ffff]
pci 0000:00:02.1: reg 10 32bit mmio: [0xdfe00000-0xdfe7ffff]
pci 0000:00:1b.0: reg 10 64bit mmio: [0xffe00000-0xffe03fff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0xd0a0-0xd0bf]
pci 0000:00:1d.1: reg 20 io port: [0xd080-0xd09f]
pci 0000:00:1d.2: reg 20 io port: [0xd060-0xd07f]
pci 0000:00:1d.3: reg 20 io port: [0xd040-0xd05f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xdff40400-0xdff407ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: Force enabled HPET at 0xfed03000
pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 004c (mask 0007)
pci 0000:00:1f.2: reg 10 io port: [0xd0f0-0xd0f7]
pci 0000:00:1f.2: reg 14 io port: [0xd0e0-0xd0e3]
pci 0000:00:1f.2: reg 18 io port: [0xd0d0-0xd0d7]
pci 0000:00:1f.2: reg 1c io port: [0xd0c0-0xd0c3]
pci 0000:00:1f.2: reg 20 io port: [0xd020-0xd02f]
pci 0000:00:1f.2: reg 24 32bit mmio: [0xdff40000-0xdff403ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 20 io port: [0xd000-0xd01f]
pci 0000:01:00.0: reg 10 io port: [0xc000-0xc0ff]
pci 0000:01:00.0: reg 18 64bit mmio: [0xffd10000-0xffd10fff]
pci 0000:01:00.0: reg 20 64bit mmio: [0xffd00000-0xffd0ffff]
pci 0000:01:00.0: reg 30 32bit mmio: [0xdfd00000-0xdfd0ffff]
pci 0000:01:00.0: supports D1 D2
pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:01:00.0: PME# disabled
pci 0000:00:1c.0: bridge io port: [0xc000-0xcfff]
pci 0000:00:1c.0: bridge 32bit mmio: [0xdfd00000-0xdfdfffff]
pci 0000:00:1c.0: bridge 64bit mmio pref: [0xffd00000-0xffdfffff]
pci 0000:02:00.0: reg 10 io port: [0xb000-0xb0ff]
pci 0000:02:00.0: reg 14 32bit mmio: [0xdfc00000-0xdfc03fff]
pci 0000:02:00.0: supports D1 D2
pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot
pci 0000:02:00.0: PME# disabled
pci 0000:00:1c.1: bridge io port: [0xb000-0xbfff]
pci 0000:00:1c.1: bridge 32bit mmio: [0xdfc00000-0xdfcfffff]
pci 0000:00:1e.0: transparent bridge
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
hpet clockevent registered
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
system 00:01: iomem range 0xe0000000-0xefffffff has been reserved
system 00:05: ioport range 0x4d0-0x4d1 has been reserved
system 00:09: ioport range 0x400-0x47f has been reserved
system 00:09: ioport range 0x1180-0x119f has been reserved
system 00:09: ioport range 0x500-0x53f has been reserved
system 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:09: iomem range 0xfed20000-0xfed23fff has been reserved
system 00:09: iomem range 0xffb00000-0xffbfffff has been reserved
system 00:09: iomem range 0xfc800400-0xfc800fff has been reserved
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01
pci 0000:00:1c.0:   IO window: 0xc000-0xcfff
pci 0000:00:1c.0:   MEM window: 0xdfd00000-0xdfdfffff
pci 0000:00:1c.0:   PREFETCH window: 0x000000ffd00000-0x000000ffdfffff
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.1:   IO window: 0xb000-0xbfff
pci 0000:00:1c.1:   MEM window: 0xdfc00000-0xdfcfffff
pci 0000:00:1c.1:   PREFETCH window: disabled
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:03
pci 0000:00:1e.0:   IO window: disabled
pci 0000:00:1e.0:   MEM window: disabled
pci 0000:00:1e.0:   PREFETCH window: disabled
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io:  [0xc000-0xcfff]
pci_bus 0000:01: resource 1 mem: [0xdfd00000-0xdfdfffff]
pci_bus 0000:01: resource 2 pref mem [0xffd00000-0xffdfffff]
pci_bus 0000:02: resource 0 io:  [0xb000-0xbfff]
pci_bus 0000:02: resource 1 mem: [0xdfc00000-0xdfcfffff]
pci_bus 0000:03: resource 3 io:  [0x00-0xffff]
pci_bus 0000:03: resource 4 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs...
Freeing initrd memory: 682k freed
apm: BIOS not found.
Scanning for low memory corruption every 60 seconds
audit: initializing netlink socket (disabled)
type=2000 audit(1260099892.546:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1746
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:02.0: Boot video device
pcieport-driver 0000:00:1c.0: irq 24 for MSI/MSI-X
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.1: irq 25 for MSI/MSI-X
pcieport-driver 0000:00:1c.1: setting latency timer to 64
isapnp: Scanning for PnP cards...
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
isapnp: No Plug & Play device found
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
input: Macintosh mouse button emulation as /devices/virtual/input/input0
i8042: PNP detection disabled
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Initalizing network drop monitor service
Freeing unused kernel memory: 416k freed
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
SCSI subsystem initialized
libata version 3.00 loaded.
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: irq 26 for MSI/MSI-X
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x5 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part 
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m1024@0xdff40000 port 0xdff40100 irq 26
ata2: DUMMY
ata3: SATA max UDMA/133 abar m1024@0xdff40000 port 0xdff40200 irq 26
ata4: DUMMY
ata3: SATA link down (SStatus 0 SControl 300)
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-8: WDC WD1200BEVT-22ZCT0, 11.01A11, max UDMA/133
ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      WDC WD1200BEVT-2 11.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
EXT4-fs (sda1): barriers enabled
kjournald2 starting: pid 481, dev sda1:8, commit interval 5 seconds
EXT4-fs (sda1): delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs (sda1): mounted filesystem with ordered data mode
rtc_cmos 00:04: RTC can wake from S4
rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
udev: starting version 146
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Linux agpgart interface v0.103
intel_rng: FWH not detected
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button [PWRF]
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:11/PNP0C09:00/PNP0C0D:00/input/input3
sd 0:0:0:0: Attached scsi generic sg0 type 0
input: PC Speaker as /devices/platform/pcspkr/input/input4
ACPI: SSDT 3f5e8c90 00253 (v02  PmRef  Cpu0Ist 00003000 INTL 20051117)
rtl8187se: module is from the staging directory, the quality is unknown, you have been warned.
ACPI: SSDT 3f5e7690 00653 (v02  PmRef  Cpu0Cst 00003001 INTL 20051117)
ACPI: Lid Switch [LID0]
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5
ACPI: Power Button [PWRB]
input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input6
ACPI: Sleep Button [SLPB]
ieee80211_crypt: registered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'TKIP'
ieee80211_crypt: registered algorithm 'CCMP'
ieee80211_crypt: registered algorithm 'WEP'

Linux kernel driver for RTL8180 / RTL8185 based WLAN cards
Copyright (c) 2004-2005, Andrea Merello
r8180: Initializing module
r8180: Wireless extensions version 22
r8180: Initializing proc filesystem
r8180: Configuring chip resources
r8180 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
r8180 0000:02:00.0: setting latency timer to 64
i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19
Monitor-Mwait will be used to enter C-1 state
r8180: Channel plan is 2

Dot11d_Init()
r8180: MAC controller is a RTL8187SE b/g
r8180: This is a PCI NIC
Monitor-Mwait will be used to enter C-2 state
r8180: usValue is 0x100

r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
r8169 0000:01:00.0: setting latency timer to 64
r8169 0000:01:00.0: irq 27 for MSI/MSI-X
eth0: RTL8102e at 0xf84e2000, 00:21:85:df:c3:c5, XID 34a00000 IRQ 27
Monitor-Mwait will be used to enter C-3 state
Marking TSC unstable due to TSC halts in idle
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
processor LNXCPU:00: registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: SSDT 3f5e8f10 000D0 (v02  PmRef  Cpu1Ist 00003000 INTL 20051117)
ACPI: SSDT 3f611b10 00083 (v02  PmRef  Cpu1Cst 00003000 INTL 20051117)
ACPI: WMI: Mapper loaded
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xdff40400
r8180: EEPROM version 104
r8180: WW:**PLEASE** REPORT SUCCESSFUL/UNSUCCESSFUL TO Realtek!
r8180: IRQ 17
r8180: Driver probe completed

ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
processor LNXCPU:01: registered as cooling_device1
ACPI: Processor [CPU1] (supports 8 throttling states)
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (29 C)
agpgart-intel 0000:00:00.0: Intel 945GME Chipset
agpgart-intel 0000:00:00.0: detected 7932K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000d0a0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d080
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
ACPI: AC Adapter [ADP1] (off-line)
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d060
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000d040
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
iTCO_vendor_support: vendor-support=0
usb 1-5: new high speed USB device using ehci_hcd and address 2
psmouse serio1: ID: 10 00 64
usb 1-5: configuration #1 chosen from 1 choice
usb 1-6: new high speed USB device using ehci_hcd and address 3
Linux video capture interface: v2.00
usb 1-6: configuration #1 chosen from 1 choice
input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input7
ACPI: Battery Slot [BAT1] (battery present)
Initializing USB Mass Storage driver...
scsi4 : SCSI emulation for USB Mass Storage devices
acpi device:1c: registered as cooling_device2
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:1a/input/input8
ACPI: Video Device [IGD] (multi-head: yes  rom: no  post: no)
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
uvcvideo: Found UVC 1.00 device USB 2.0 Camera (0c45:62c0)
input: USB 2.0 Camera as /devices/pci0000:00/0000:00:1d.7/usb1/1-5/1-5:1.0/input/input9
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: Found a ICH7-M or ICH7-U TCO device (Version=2, TCOBASE=0x0460)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
HDA Intel 0000:00:1b.0: setting latency timer to 64
hda_codec: Unknown model for ALC1200, trying auto-probe from BIOS...
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input10
EXT4-fs (sda1): internal journal on sda1:8
Clocksource tsc unstable (delta = -111904481 ns)
EXT4-fs (sda3): barriers enabled
kjournald2 starting: pid 968, dev sda3:8, commit interval 5 seconds
EXT4-fs (sda3): internal journal on sda3:8
EXT4-fs (sda3): delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs (sda3): mounted filesystem with ordered data mode
Adding 996020k swap on /dev/sda2.  Priority:-1 extents:1 across:996020k

OK, i solved that one

I had to re-setup deamons properly in rc.conf
before

DAEMONS=(syslog-ng hal !network !netfs dbus bluetooth crond alsa wicd kdm)

after

DAEMONS=(syslog-ng hal !network !netfs bluetooth crond alsa wicd kdm)

I removed dbus, since it is automatically loaded by hal anyway. Now hot-pluging devices works.

Last edited by bagheera (2009-12-05 19:10:15)

Arch Linux

#1 2008-08-28 07:42:42

Serious problem on USB "hotplug"

#2 2008-08-29 08:04:07

Re: Serious problem on USB "hotplug"

#3 2008-08-29 17:13:54

Re: Serious problem on USB "hotplug"

#4 2008-08-29 18:45:24

Re: Serious problem on USB "hotplug"

#5 2008-09-05 19:23:33

Re: Serious problem on USB "hotplug"

#6 2008-09-12 08:45:47

Re: Serious problem on USB "hotplug"

#7 2009-12-05 11:51:55

Re: Serious problem on USB "hotplug"

Board footer