Arch Linux

FooSoft

Member

Registered: 2009-04-10

Posts: 15

Website

[Solved] Failure to stop HAL on shutdown afer install wicd

Hey guys, I'm running into kind of an annoying issue. Whenever I go to restart my machine it will display an error on stopping HAL. This just started happening after I installed wicd. Any ideas on what could be going on here?

rc.conf:

#
# /etc/rc.conf - Main Configuration for Arch Linux
#

# -----------------------------------------------------------------------
# LOCALIZATION
# -----------------------------------------------------------------------
#
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
#
LOCALE="en_US.utf8"
HARDWARECLOCK="UTC"
USEDIRECTISA="no"
TIMEZONE="America/Los_Angeles"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"

# -----------------------------------------------------------------------
# HARDWARE
# -----------------------------------------------------------------------
#
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
#
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
#
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=(rt3090sta)

# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"

# -----------------------------------------------------------------------
# NETWORKING
# -----------------------------------------------------------------------
#
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
#
HOSTNAME="misaka"

# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
#
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
#   - prefix an entry in INTERFACES with a ! to disable it
#   - no hyphens in your interface names - Bash doesn't like it
# 
# DHCP:     Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
#

#Static IP example
#eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
#eth0="dhcp"
#wlan0="dhcp"
INTERFACES=(!eth0 !wlan0)

# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
#   - prefix an entry in ROUTES with a ! to disable it
#
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
 
# Enable these network profiles at boot-up.  These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
#   - set to 'menu' to present a menu during boot-up (dialog package required)
#   - prefix an entry with a ! to disable it
#
# Network profiles are found in /etc/network.d
#
# This now requires the netcfg package
#
#NETWORKS=(main)

# -----------------------------------------------------------------------
# DAEMONS
# -----------------------------------------------------------------------
#
# Daemons to start at boot-up (in this order)
#   - prefix a daemon with a ! to disable it
#   - prefix a daemon with a @ to start it up in the background
#
DAEMONS=(syslog-ng hal network netfs crond hal sshd wicd)

Last edited by FooSoft (2009-12-05 21:48:43)

FooSoft

Member

Registered: 2009-04-10

Posts: 15

Website

Re: [Solved] Failure to stop HAL on shutdown afer install wicd

Nevermind, I'm an idiot. I hat HAL listed twice in daemon array.