You are not logged in.
- Topics: Active | Unanswered
#1 2009-12-26 23:47:16
- FooSoft
- Member
- Registered: 2009-04-10
- Posts: 15
- Website
xrandr not listing dual head outputs
I'm running into a little annoying problem with xrandr. It doesn't want to list my nvidia 8800gt's dual heads as different outputs.
[foosoft@asakura ~]$ xrandr
Screen 0: minimum 320 x 175, current 1920 x 1200, maximum 1920 x 1200
default connected 1920x1200+0+0 0mm x 0mm
1920x1200 50.0*
1680x1050 51.0 52.0
1600x1200 53.0 54.0
1440x900 55.0 56.0
1400x1050 57.0 58.0 59.0
1280x1024 60.0 61.0 62.0
1280x960 63.0 64.0
1152x864 65.0
1024x768 66.0 67.0 68.0 69.0 70.0 71.0 72.0
960x720 73.0 74.0 75.0
928x696 76.0 77.0
896x672 78.0 79.0
832x624 80.0
800x600 81.0 82.0 83.0 84.0 85.0 86.0 87.0 88.0 89.0 90.0
720x400 91.0
700x525 92.0 93.0
640x512 94.0 95.0 96.0
640x480 97.0 98.0 99.0 100.0 101.0 102.0 103.0 104.0
640x400 105.0
640x350 106.0
576x432 107.0
512x384 108.0 109.0 110.0 111.0 112.0
416x312 113.0
400x300 114.0 115.0 116.0 117.0 118.0
360x200 119.0
320x240 120.0 121.0 122.0 123.0
320x200 124.0
320x175 125.0So it only lists "default" even though I have a second monitor plugged in over DVI (a TV actually). I know it's not a problem with output to the TV because if I specifically set up output in xorg.conf it works fine. However I would much prefer to enable and disable output to TV on an as-needed basis.
Here's my xorg.conf:
[foosoft@asakura ~]$ cat /etc/X11/xorg.conf
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 1.0 (buildmeister@builder58) Tue Oct 20 21:25:04 PDT 2009
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0" 0 0
#Screen 1 "Screen1" Above "Screen0"
Option "Xinerama" "0"
EndSection
Section "Monitor"
# HorizSync source: edid, VertRefresh source: edid
Identifier "Monitor0"
VendorName "Unknown"
ModelName "Gateway FHD2400"
HorizSync 31.0 - 83.0
VertRefresh 56.0 - 76.0
Option "DPMS"
EndSection
Section "Monitor"
# HorizSync source: edid, VertRefresh source: edid
Identifier "Monitor1"
VendorName "Unknown"
ModelName "SONY TV"
HorizSync 15.0 - 46.0
VertRefresh 59.0 - 61.0
Option "DPMS"
EndSection
Section "Device"
Identifier "Device0"
Driver "nvidia"
VendorName "NVIDIA Corporation"
BoardName "GeForce 8800 GT"
BusID "PCI:1:0:0"
Screen 0
EndSection
Section "Device"
Identifier "Device1"
Driver "nvidia"
VendorName "NVIDIA Corporation"
BoardName "GeForce 8800 GT"
BusID "PCI:1:0:0"
Screen 1
EndSection
Section "Screen"
Identifier "Screen0"
Device "Device0"
Monitor "Monitor0"
DefaultDepth 24
Option "TwinView" "0"
Option "metamodes" "DFP-0: nvidia-auto-select +0+0"
SubSection "Display"
Depth 24
EndSubSection
EndSection
Section "Screen"
Identifier "Screen1"
Device "Device1"
Monitor "Monitor1"
DefaultDepth 24
Option "TwinView" "0"
Option "metamodes" "DFP-1: 1280x720 +0+0"
SubSection "Display"
Depth 24
EndSubSection
EndSection
Section "Extensions"
Option "Composite" "Enable"
Option "AGPFastWrite" "true"
Option "EnablePageFlip" "true"
EndSectionAnd my X11 log:
[foosoft@asakura ~]$ cat /var/log/Xorg.0.log
This is a pre-release version of the X server from The X.Org Foundation.
It is not supported in any way.
Bugs may be filed in the bugzilla at http://bugs.freedesktop.org/.
Select the "xorg" product for bugs you find in this release.
Before reporting bugs in pre-release versions please check the
latest version in the X.Org Foundation git repository.
See http://wiki.x.org/wiki/GitPage for git access instructions.
X.Org X Server 1.7.3.901 (1.7.4 RC 1)
Release Date: 2009-12-11
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.32-ARCH x86_64
Current Operating System: Linux asakura 2.6.31-ARCH #1 SMP PREEMPT Tue Nov 10 19:01:40 CET 2009 x86_64
Kernel command line: root=/dev/disk/by-uuid/3695c065-a8fe-4574-9ae8-d67e25387b14 ro
Build Date: 12 December 2009 08:39:02PM
Current version of pixman: 0.16.4
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sat Dec 26 15:37:16 2009
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "Layout0"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "Monitor0"
(**) | |-->Device "Device0"
(**) Option "Xinerama" "0"
(==) Automatically adding devices
(==) Automatically enabling devices
(==) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/Type1
(==) ModulePath set to "/usr/lib/xorg/modules"
(**) Extension "Composite" is enabled
(WW) Ignoring unrecognized extension "AGPFastWrite"
(WW) Ignoring unrecognized extension "EnablePageFlip"
(II) Cannot locate a core pointer device.
(II) Cannot locate a core keyboard device.
(II) The server relies on HAL to provide the list of input devices.
If no devices become available, reconfigure HAL or disable AutoAddDevices.
(II) Loader magic: 0x7c09a0
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 6.0
X.Org XInput driver : 7.0
X.Org Server Extension : 2.0
(++) using VT number 7
(--) PCI:*(0:1:0:0) 10de:0611:1462:8010 nVidia Corporation G92 [GeForce 8800 GT] rev 162, Mem @ 0xfa000000/16777216, 0xd0000000/268435456, 0xf8000000/33554432, I/O @ 0x0000af00/128, BIOS @ 0x????????/131072
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.7.3.901, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.7.3.901, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions/libglx.so
(II) Module glx: vendor="NVIDIA Corporation"
compiled for 4.0.2, module version = 1.0.0
Module class: X.Org Server Extension
(II) NVIDIA GLX Module 190.42 Tue Oct 20 21:19:30 PDT 2009
(II) Loading extension GLX
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions/libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.7.3.901, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.7.3.901, module version = 1.1.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "nvidia"
(II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
(II) Module nvidia: vendor="NVIDIA Corporation"
compiled for 4.0.2, module version = 1.0.0
Module class: X.Org Video Driver
(II) NVIDIA dlloader X Driver 190.42 Tue Oct 20 20:42:04 PDT 2009
(II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
(II) Primary Device is: PCI 01@00:00:0
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules/libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.7.3.901, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "wfb"
(II) LoadModule: "wfb"
(II) Loading /usr/lib/xorg/modules/libwfb.so
(II) Module wfb: vendor="X.Org Foundation"
compiled for 1.7.3.901, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(WW) VGA arbiter: cannot open kernel arbiter, no multi-card support
(**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32
(==) NVIDIA(0): RGB weight 888
(==) NVIDIA(0): Default visual is TrueColor
(==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
(**) NVIDIA(0): Option "TwinView" "0"
(**) NVIDIA(0): Option "MetaModes" "DFP-0: nvidia-auto-select +0+0"
(**) Dec 26 15:37:17 NVIDIA(0): Enabling RENDER acceleration
(II) Dec 26 15:37:17 NVIDIA(0): Support for GLX with the Damage and Composite X extensions is
(II) Dec 26 15:37:17 NVIDIA(0): enabled.
(II) Dec 26 15:37:19 NVIDIA(0): NVIDIA GPU GeForce 8800 GT (G92) at PCI:1:0:0 (GPU-0)
(--) Dec 26 15:37:19 NVIDIA(0): Memory: 524288 kBytes
(--) Dec 26 15:37:19 NVIDIA(0): VideoBIOS: 62.92.12.00.04
(II) Dec 26 15:37:19 NVIDIA(0): Detected PCI Express Link width: 16X
(--) Dec 26 15:37:19 NVIDIA(0): Interlaced video modes are supported on this GPU
(--) Dec 26 15:37:19 NVIDIA(0): Connected display device(s) on GeForce 8800 GT at PCI:1:0:0:
(--) Dec 26 15:37:19 NVIDIA(0): Gateway FHD2400 (DFP-0)
(--) Dec 26 15:37:19 NVIDIA(0): SONY TV (DFP-1)
(--) Dec 26 15:37:19 NVIDIA(0): Gateway FHD2400 (DFP-0): 330.0 MHz maximum pixel clock
(--) Dec 26 15:37:19 NVIDIA(0): Gateway FHD2400 (DFP-0): Internal Dual Link TMDS
(--) Dec 26 15:37:19 NVIDIA(0): SONY TV (DFP-1): 330.0 MHz maximum pixel clock
(--) Dec 26 15:37:19 NVIDIA(0): SONY TV (DFP-1): Internal Dual Link TMDS
(II) Dec 26 15:37:19 NVIDIA(0): Display Device found referenced in MetaMode: DFP-0
(II) Dec 26 15:37:19 NVIDIA(0): Assigned Display Device: DFP-0
(II) Dec 26 15:37:19 NVIDIA(0): Validated modes:
(II) Dec 26 15:37:19 NVIDIA(0): "DFP-0:nvidia-auto-select+0+0"
(II) Dec 26 15:37:19 NVIDIA(0): Virtual screen size determined to be 1920 x 1200
(--) Dec 26 15:37:19 NVIDIA(0): DPI set to (93, 95); computed from "UseEdidDpi" X config
(--) Dec 26 15:37:19 NVIDIA(0): option
(==) Dec 26 15:37:19 NVIDIA(0): Enabling 32-bit ARGB GLX visuals.
(--) Depth 24 pixmap format is 32 bpp
(II) Dec 26 15:37:19 NVIDIA(0): Initialized GPU GART.
(II) Dec 26 15:37:19 NVIDIA(0): ACPI: failed to connect to the ACPI event daemon; the daemon
(II) Dec 26 15:37:19 NVIDIA(0): may not be running or the "AcpidSocketPath" X
(II) Dec 26 15:37:19 NVIDIA(0): configuration option may not be set correctly. When the
(II) Dec 26 15:37:19 NVIDIA(0): ACPI event daemon is available, the NVIDIA X driver will
(II) Dec 26 15:37:19 NVIDIA(0): try to use it to receive ACPI event notifications. For
(II) Dec 26 15:37:19 NVIDIA(0): details, please see the "ConnectToAcpid" and
(II) Dec 26 15:37:19 NVIDIA(0): "AcpidSocketPath" X configuration options in Appendix B: X
(II) Dec 26 15:37:19 NVIDIA(0): Config Options in the README.
(II) Dec 26 15:37:19 NVIDIA(0): Setting mode "DFP-0:nvidia-auto-select+0+0"
(II) Loading extension NV-GLX
(II) Dec 26 15:37:19 NVIDIA(0): Initialized OpenGL Acceleration
(==) NVIDIA(0): Disabling shared memory pixmaps
(II) Dec 26 15:37:19 NVIDIA(0): Initialized X Rendering Acceleration
(==) NVIDIA(0): Backing store disabled
(==) NVIDIA(0): Silken mouse enabled
(**) NVIDIA(0): DPMS enabled
(II) Loading extension NV-CONTROL
(II) Loading extension XINERAMA
(==) RandR enabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing extension GLX
(II) config/hal: Adding input device Macintosh mouse button emulation
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
compiled for 1.7.3, module version = 2.3.2
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 7.0
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event0"
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Found relative axes
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Configuring as mouse
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
(**) Macintosh mouse button emulation: (accel) acceleration profile 0
(II) Macintosh mouse button emulation: initialized for relative axes.
(II) config/hal: Adding input device AT Translated Set 2 keyboard
(**) AT Translated Set 2 keyboard: always reports core events
(**) AT Translated Set 2 keyboard: Device: "/dev/input/event1"
(II) AT Translated Set 2 keyboard: Found keys
(II) AT Translated Set 2 keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)
(**) Microsoft Microsoft 5-Button Mouse with IntelliEye(TM): always reports core events
(**) Microsoft Microsoft 5-Button Mouse with IntelliEye(TM): Device: "/dev/input/event5"
(II) Microsoft Microsoft 5-Button Mouse with IntelliEye(TM): Found 9 mouse buttons
(II) Microsoft Microsoft 5-Button Mouse with IntelliEye(TM): Found scroll wheel(s)
(II) Microsoft Microsoft 5-Button Mouse with IntelliEye(TM): Found relative axes
(II) Microsoft Microsoft 5-Button Mouse with IntelliEye(TM): Found x and y relative axes
(II) Microsoft Microsoft 5-Button Mouse with IntelliEye(TM): Configuring as mouse
(**) Microsoft Microsoft 5-Button Mouse with IntelliEye(TM): YAxisMapping: buttons 4 and 5
(**) Microsoft Microsoft 5-Button Mouse with IntelliEye(TM): EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)" (type: MOUSE)
(**) Microsoft Microsoft 5-Button Mouse with IntelliEye(TM): (accel) keeping acceleration scheme 1
(**) Microsoft Microsoft 5-Button Mouse with IntelliEye(TM): (accel) acceleration profile 0
(II) Microsoft Microsoft 5-Button Mouse with IntelliEye(TM): initialized for relative axes.
(II) config/hal: Adding input device Power Button
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event4"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Power Button
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event3"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"Any ideas?
Last edited by FooSoft (2009-12-26 23:50:25)
Offline