You are not logged in.
I believe I've got pretty much everything working on my 1000H except for bluetooth. I can't seem to get the hardware working. The module is loaded, and dmesg has references to bluetooth, but blueman does not list the adapter, and running "hcitool scan" from the command line returns "Device is not available: No such device".
I've enabled every bluetooth-related item I can find in the kernel, so I don't see what I'm missing. I did import the config from the stock kernel, where bluetooth was working fine.
#
# /etc/rc.conf - Main Configuration for Arch Linux
#
# -----------------------------------------------------------------------
# LOCALIZATION
# -----------------------------------------------------------------------
#
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime", any other value will result
# in the hardware clock being left untouched (useful for virtualization)
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
#
LOCALE="en_US.UTF-8"
HARDWARECLOCK="UTC"
TIMEZONE="America/Los_Angeles"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# -----------------------------------------------------------------------
# HARDWARE
# -----------------------------------------------------------------------
#
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
#
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
#
MOD_AUTOLOAD="no"
#MOD_BLACKLIST=() #deprecated
MODULES=(atl1e rt2860sta rndis_host cdc_ether usbnet rfkill acpi-cpufreq pciehp intel_agp snd-hda-intel !snd-pcsp bluetooth !eeepc_laptop)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# -----------------------------------------------------------------------
# NETWORKING
# -----------------------------------------------------------------------
#
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
#
HOSTNAME="sprice-l"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
#
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
#
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
#
#Static IP example
#eth0="dhcp"
eth0="dhcp"
wlan0="dhcp"
INTERFACES=(!eth0 !wlan0)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
#
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
#
# Network profiles are found in /etc/network.d
#
# This now requires the netcfg package
#
#NETWORKS=(main)
# -----------------------------------------------------------------------
# DAEMONS
# -----------------------------------------------------------------------
#
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
#
DAEMONS=(syslog-ng !network @acpid @crond hal networkmanager netfs bluetooth @alsa @openntpd gdm)dmesg:
Linux version 2.6.32-ARCH (root@sprice-l) (gcc version 4.4.2 20091208 (prerelease) (GCC) ) #5 SMP PREEMPT Tue Dec 29 09:02:31 PST 2009
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
NSC Geode by NSC
Cyrix CyrixInstead
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
UMC UMC UMC UMC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e2000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003f7a0000 (usable)
BIOS-e820: 000000003f7a0000 - 000000003f7ae000 (ACPI data)
BIOS-e820: 000000003f7ae000 - 000000003f7f0000 (ACPI NVS)
BIOS-e820: 000000003f7f0000 - 000000003f800000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
DMI present.
AMI BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
last_pfn = 0x3f7a0 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-DFFFF uncachable
E0000-EFFFF write-through
F0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask 0C0000000 write-back
1 base 03F800000 mask 0FF800000 uncachable
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Scanning 0 areas for low memory corruption
modified physical RAM map:
modified: 0000000000000000 - 0000000000010000 (reserved)
modified: 0000000000010000 - 000000000009fc00 (usable)
modified: 000000000009fc00 - 00000000000a0000 (reserved)
modified: 00000000000e2000 - 0000000000100000 (reserved)
modified: 0000000000100000 - 000000003f7a0000 (usable)
modified: 000000003f7a0000 - 000000003f7ae000 (ACPI data)
modified: 000000003f7ae000 - 000000003f7f0000 (ACPI NVS)
modified: 000000003f7f0000 - 000000003f800000 (reserved)
modified: 00000000fee00000 - 00000000fee01000 (reserved)
modified: 00000000fff80000 - 0000000100000000 (reserved)
initial memory mapped : 0 - 01c00000
init_memory_mapping: 0000000000000000-00000000377fe000
0000000000 - 0000400000 page 4k
0000400000 - 0037400000 page 2M
0037400000 - 00377fe000 page 4k
kernel direct mapping tables up to 377fe000 @ 10000-15000
RAMDISK: 3f735000 - 3f78fc32
Allocated new RAMDISK: 00011000 - 0006bc32
Move RAMDISK from 000000003f735000 - 000000003f78fc31 to 00011000 - 0006bc31
ACPI: RSDP 000fb9f0 00014 (v00 ACPIAM)
ACPI: RSDT 3f7a0000 0003C (v01 A_M_I_ OEMRSDT 08000801 MSFT 00000097)
ACPI: FACP 3f7a0200 00084 (v02 A_M_I_ OEMFACP 08000801 MSFT 00000097)
ACPI: DSDT 3f7a05b0 05050 (v01 A1028 A1028000 00000000 INTL 20051117)
ACPI: FACS 3f7ae000 00040
ACPI: APIC 3f7a0390 0005C (v01 A_M_I_ OEMAPIC 08000801 MSFT 00000097)
ACPI: MCFG 3f7a03f0 0003C (v01 A_M_I_ OEMMCFG 08000801 MSFT 00000097)
ACPI: OEMB 3f7ae040 00061 (v01 A_M_I_ AMI_OEM 08000801 MSFT 00000097)
ACPI: HPET 3f7a5600 00038 (v01 A_M_I_ OEMHPET 08000801 MSFT 00000097)
ACPI: SSDT 3f7aeb80 004F0 (v01 PmRef CpuPm 00003000 INTL 20051117)
ACPI: Local APIC address 0xfee00000
127MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 0 - 377fe000
node 0 low ram: 00000000 - 377fe000
node 0 bootmap 0006c000 - 00072f00
(9 early reservations) ==> bootmem [0000000000 - 00377fe000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0001000000 - 000167a084] TEXT DATA BSS ==> [0001000000 - 000167a084]
#4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
#5 [000167b000 - 00016821fc] BRK ==> [000167b000 - 00016821fc]
#6 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000]
#7 [0000011000 - 000006bc32] NEW RAMDISK ==> [0000011000 - 000006bc32]
#8 [000006c000 - 0000073000] BOOTMAP ==> [000006c000 - 0000073000]
found SMP MP-table at [c00ff780] ff780
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x0003f7a0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x0003f7a0
On node 0 totalpages: 259887
free_area_init_node: node 0, pgdat c1548600, node_mem_map c1684200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3951 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 256 pages used for memmap
HighMem zone: 32418 pages, LIFO batch:7
Using APIC driver default
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0xffffffff base: 0xfed00000
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e2000
PM: Registered nosave memory: 00000000000e2000 - 0000000000100000
Allocating PCI resources starting at 3f800000 (gap: 3f800000:bf600000)
Booting paravirtualized kernel on bare hardware
NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 13 pages/cpu @c2000000 s29720 r0 d23528 u2097152
pcpu-alloc: s29720 r0 d23528 u2097152 alloc=1*4194304
pcpu-alloc: [0] 0 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 257855
Kernel command line: root=/dev/disk/by-uuid/21e88bd5-5449-4926-8ed4-80fce8263ceb ro
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Initializing HighMem for node 0 (000377fe:0003f7a0)
Memory: 1023012k/1040000k available (4034k kernel code, 16100k reserved, 1396k data, 408k init, 130696k highmem)
virtual kernel memory layout:
fixmap : 0xfff1e000 - 0xfffff000 ( 900 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc154e000 - 0xc15b4000 ( 408 kB)
.data : 0xc13f08c2 - 0xc154daf8 (1396 kB)
.text : 0xc1000000 - 0xc13f08c2 (4034 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:512
Console: colour VGA+ 80x25
console [tty0] enabled
hpet clockevent registered
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
Fast TSC calibration using PIT
Detected 1596.133 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 3193.27 BogoMIPS (lpj=5320443)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 24K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 5 MCE banks
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
Performance Events: Atom events, Intel PMU driver.
... version: 3
... bit width: 40
... generic registers: 2
... value mask: 000000ffffffffff
... max period: 000000007fffffff
... fixed-purpose events: 3
... event mask: 0000000700000003
Checking 'hlt' instruction... OK.
ACPI: Core revision 20090903
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Atom(TM) CPU N270 @ 1.60GHz stepping 02
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3193.98 BogoMIPS (lpj=5319968)
CPU: L1 I cache: 32K, L1 D cache: 24K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU1: Thermal monitoring enabled (TM2)
CPU1: Intel(R) Atom(TM) CPU N270 @ 1.60GHz stepping 02
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (6386.25 BogoMIPS).
CPU0 attaching sched-domain:
domain 0: span 0-1 level SIBLING
groups: 0 (cpu_power = 589) 1 (cpu_power = 589)
domain 1: span 0-1 level MC
groups: 0-1 (cpu_power = 1178)
CPU1 attaching sched-domain:
domain 0: span 0-1 level SIBLING
groups: 1 (cpu_power = 589) 0 (cpu_power = 589)
domain 1: span 0-1 level MC
groups: 0-1 (cpu_power = 1178)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 63
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Executed 1 blocks of module-level executable AML code
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 63
PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
PCI: Using MMCONFIG for extended config space
ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:02.0: reg 10 32bit mmio: [0xf7f00000-0xf7f7ffff]
pci 0000:00:02.0: reg 14 io port: [0xdc00-0xdc07]
pci 0000:00:02.0: reg 18 32bit mmio pref: [0xd0000000-0xdfffffff]
pci 0000:00:02.0: reg 1c 32bit mmio: [0xf7ec0000-0xf7efffff]
pci 0000:00:02.1: reg 10 32bit mmio: [0xf7f80000-0xf7ffffff]
pci 0000:00:1b.0: reg 10 64bit mmio: [0xf7eb8000-0xf7ebbfff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.3: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0xd400-0xd41f]
pci 0000:00:1d.1: reg 20 io port: [0xd480-0xd49f]
pci 0000:00:1d.2: reg 20 io port: [0xd800-0xd81f]
pci 0000:00:1d.3: reg 20 io port: [0xd880-0xd89f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xf7eb7c00-0xf7eb7fff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0380 (mask 0003)
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0290 (mask 0007)
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0068 (mask 0003)
pci 0000:00:1f.2: reg 10 io port: [0x00-0x07]
pci 0000:00:1f.2: reg 14 io port: [0x00-0x03]
pci 0000:00:1f.2: reg 18 io port: [0x00-0x07]
pci 0000:00:1f.2: reg 1c io port: [0x00-0x03]
pci 0000:00:1f.2: reg 20 io port: [0xffa0-0xffaf]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:03:00.0: reg 10 64bit mmio: [0xfbfc0000-0xfbffffff]
pci 0000:03:00.0: reg 18 io port: [0xec00-0xec7f]
pci 0000:03:00.0: PME# supported from D3hot D3cold
pci 0000:03:00.0: PME# disabled
pci 0000:00:1c.1: bridge io port: [0xe000-0xefff]
pci 0000:00:1c.1: bridge 32bit mmio: [0xfbf00000-0xfbffffff]
pci 0000:01:00.0: reg 10 32bit mmio: [0xfbef0000-0xfbefffff]
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:00:1c.3: bridge 32bit mmio: [0xf8000000-0xfbefffff]
pci 0000:00:1c.3: bridge 64bit mmio pref: [0xf0000000-0xf6ffffff]
pci 0000:00:1e.0: transparent bridge
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12 14 15)
vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
Switching to clocksource tsc
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
system 00:08: ioport range 0x25c-0x25f has been reserved
system 00:08: ioport range 0x380-0x383 has been reserved
system 00:08: ioport range 0x400-0x41f has been reserved
system 00:08: ioport range 0x4d0-0x4d1 has been reserved
system 00:08: ioport range 0x800-0x87f has been reserved
system 00:08: ioport range 0x480-0x4bf has been reserved
system 00:08: iomem range 0x8c000000-0x8c01ffff has been reserved
system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:08: iomem range 0xfed50000-0xfed8ffff has been reserved
system 00:08: iomem range 0xffb00000-0xffbfffff has been reserved
system 00:08: iomem range 0xfff00000-0xffffffff could not be reserved
system 00:0a: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0b: iomem range 0xe0000000-0xe3ffffff has been reserved
system 00:0c: iomem range 0x0-0x9ffff could not be reserved
system 00:0c: iomem range 0xc0000-0xcffff could not be reserved
system 00:0c: iomem range 0xe0000-0xfffff could not be reserved
system 00:0c: iomem range 0x100000-0x3f7fffff could not be reserved
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:04
pci 0000:00:1c.0: IO window: 0x1000-0x1fff
pci 0000:00:1c.0: MEM window: 0x40000000-0x401fffff
pci 0000:00:1c.0: PREFETCH window: 0x00000040200000-0x000000403fffff
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
pci 0000:00:1c.1: IO window: 0xe000-0xefff
pci 0000:00:1c.1: MEM window: 0xfbf00000-0xfbffffff
pci 0000:00:1c.1: PREFETCH window: 0x00000040400000-0x000000405fffff
pci 0000:00:1c.3: PCI bridge, secondary bus 0000:01
pci 0000:00:1c.3: IO window: 0x2000-0x2fff
pci 0000:00:1c.3: MEM window: 0xf8000000-0xfbefffff
pci 0000:00:1c.3: PREFETCH window: 0x000000f0000000-0x000000f6ffffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05
pci 0000:00:1e.0: IO window: disabled
pci 0000:00:1e.0: MEM window: disabled
pci 0000:00:1e.0: PREFETCH window: disabled
pci 0000:00:1c.0: enabling device (0104 -> 0107)
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1c.3: enabling device (0106 -> 0107)
pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
pci 0000:00:1c.3: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:04: resource 0 io: [0x1000-0x1fff]
pci_bus 0000:04: resource 1 mem: [0x40000000-0x401fffff]
pci_bus 0000:04: resource 2 pref mem [0x40200000-0x403fffff]
pci_bus 0000:03: resource 0 io: [0xe000-0xefff]
pci_bus 0000:03: resource 1 mem: [0xfbf00000-0xfbffffff]
pci_bus 0000:03: resource 2 pref mem [0x40400000-0x405fffff]
pci_bus 0000:01: resource 0 io: [0x2000-0x2fff]
pci_bus 0000:01: resource 1 mem: [0xf8000000-0xfbefffff]
pci_bus 0000:01: resource 2 pref mem [0xf0000000-0xf6ffffff]
pci_bus 0000:05: resource 3 io: [0x00-0xffff]
pci_bus 0000:05: resource 4 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
pci 0000:00:02.0: Boot video device
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 363k freed
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
Scanning for low memory corruption every 60 seconds
audit: initializing netlink socket (disabled)
type=2000 audit(1262112860.302:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Slow work thread pool: Starting up
Slow work thread pool: Ready
NTFS driver 2.1.29 [Flags: R/W DEBUG].
fuse init (API version 7.13)
SGI XFS with security attributes, large block/inode numbers, no debug enabled
msgmni has been set to 1744
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pcieport 0000:00:1c.0: irq 24 for MSI/MSI-X
pcieport 0000:00:1c.0: setting latency timer to 64
pcieport 0000:00:1c.1: irq 25 for MSI/MSI-X
pcieport 0000:00:1c.1: setting latency timer to 64
pcieport 0000:00:1c.3: irq 26 for MSI/MSI-X
pcieport 0000:00:1c.3: setting latency timer to 64
ACPI: AC Adapter [AC0] (on-line)
input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
ACPI: Lid Switch [LID]
input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
ACPI: Sleep Button [SLPB]
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
ACPI: Power Button [PWRF]
ACPI: SSDT 3f7ae180 0023C (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
ACPI: SSDT 3f7ae450 00724 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Marking TSC unstable due to TSC halts in idle
processor LNXCPU:00: registered as cooling_device0
ACPI: SSDT 3f7ae0b0 000CC (v01 PmRef Cpu1Ist 00003000 INTL 20051117)
ACPI: SSDT 3f7ae3c0 00085 (v01 PmRef Cpu1Cst 00003000 INTL 20051117)
Switching to clocksource hpet
processor LNXCPU:01: registered as cooling_device1
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [TZ00] (53 C)
isapnp: Scanning for PnP cards...
ACPI: Battery Slot [BAT0] (battery present)
isapnp: No Plug & Play device found
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
brd: module loaded
loop: module loaded
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: using broken periodic workaround
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf7eb7c00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000d400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d480
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000d880
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 408k freed
BFS CPU scheduler v0.313 by Con Kolivas.
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
usb 1-5: new high speed USB device using ehci_hcd and address 2
usb 1-5: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
libata version 3.00 loaded.
ata_piix 0000:00:1f.2: version 2.13
ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ata_piix 0000:00:1f.2: setting latency timer to 64
scsi1 : ata_piix
scsi2 : ata_piix
ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
usb 1-8: new high speed USB device using ehci_hcd and address 4
ata1.00: ATA-7: ST980811AS, 3.ALC, max UDMA/133
ata1.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32)
elantech.c: assuming hardware version 2, firmware version 2.48
ata1.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA ST980811AS 3.AL PQ: 0 ANSI: 5
sd 1:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3
usb 1-8: configuration #1 chosen from 1 choice
sd 1:0:0:0: [sda] Attached SCSI disk
elantech.c: Synaptics capabilities query result 0x00, 0x02, 0x64.
usb 5-1: new full speed USB device using uhci_hcd and address 2
input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input5
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
usb 5-1: configuration #1 chosen from 1 choice
Driver 'rtc_cmos' needs updating - please use bus_type methods
rtc_cmos 00:03: RTC can wake from S4
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
udev: starting version 146
ATL1E 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
ATL1E 0000:03:00.0: setting latency timer to 64
rt2860sta: module is from the staging directory, the quality is unknown, you have been warned.
rt2860 0000:01:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
=== pAd = f825a000, size = 580808 ===
<-- RTMPAllocAdapterBlock, Status=0
rt2860 0000:01:00.0: setting latency timer to 64
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver rndis_host
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel 945GME Chipset
agpgart-intel 0000:00:00.0: detected 7932K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
scsi 0:0:0:0: Direct-Access Single Flash Reader 1.00 PQ: 0 ANSI: 0
sd 0:0:0:0: [sdb] 1984000 512-byte logical blocks: (1.01 GB/968 MiB)
sd 0:0:0:0: [sdb] Write Protect is off
sd 0:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 0:0:0:0: [sdb] Assuming drive cache: write through
usb-storage: device scan complete
sd 0:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 0:0:0:0: [sdb] Assuming drive cache: write through
sd 0:0:0:0: [sdb] Attached SCSI removable disk
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
HDA Intel 0000:00:1b.0: setting latency timer to 64
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input6
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
EXT3 FS on sda3, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
Adding 1951888k swap on /dev/sda1. Priority:-1 extents:1 across:1951888k SS
Bluetooth: L2CAP ver 2.14
Bluetooth: L2CAP socket layer initialized
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
eeepc_laptop: Eee PC Hotkey Driver
eeepc_laptop: Hotkey init flags 0x41
eeepc_laptop: TYPE (2000000) not reported by BIOS, enabling anyway
eeepc_laptop: PANELPOWER (4000000) not reported by BIOS, enabling anyway
eeepc_laptop: Get control methods supported: 0x6101713
input: Asus EeePC extra buttons as /devices/platform/eeepc/input/input7
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input8
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[drm] Initialized drm 1.1.0 20060810
pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:02.0: setting latency timer to 64
[drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
ATL1E 0000:03:00.0: irq 27 for MSI/MSI-X
RX DESC f6a56000 size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
--> Error 2 opening /etc/Wireless/RT2860STA/RT2860STA.dat
1. Phy Mode = 0
2. Phy Mode = 0
RTMPSetPhyMode: channel is out of range, use first channel=1
3. Phy Mode = 0
MCS Set = 00 00 00 00 00
<==== RTMPInitialize, Status=0
0x1300 = 00073200
===>rt_ioctl_giwscan. 24(24) BSS returned, data->length = 2895
CPU0 attaching NULL sched-domain.
CPU1 attaching NULL sched-domain.
CPU0 attaching sched-domain:
domain 0: span 0-1 level SIBLING
groups: 0 (cpu_power = 589) 1 (cpu_power = 589)
domain 1: span 0-1 level MC
groups: 0-1 (cpu_power = 1178)
CPU1 attaching sched-domain:
domain 0: span 0-1 level SIBLING
groups: 1 (cpu_power = 589) 0 (cpu_power = 589)
domain 1: span 0-1 level MC
groups: 0-1 (cpu_power = 1178)
ERROR!!! RTMPCancelTimer failed, Timer hasn't been initialize!
===>rt_ioctl_giwscan. 27(27) BSS returned, data->length = 3340
===>rt_ioctl_giwscan. 24(24) BSS returned, data->length = 3033
==>rt_ioctl_siwfreq::SIOCSIWFREQ[cmd=0x8b04] (Channel=1)
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
===>rt_ioctl_giwscan. 33(33) BSS returned, data->length = 4186
===>rt_ioctl_giwscan. 31(31) BSS returned, data->length = 3779
===>rt_ioctl_giwscan. 27(27) BSS returned, data->length = 3232
===>rt_ioctl_giwscan. 26(26) BSS returned, data->length = 3185
ERROR!!! RTMPCancelTimer failed, Timer hasn't been initialize!
ERROR!!! RTMPCancelTimer failed, Timer hasn't been initialize!
===>rt_ioctl_giwscan. 29(29) BSS returned, data->length = 3623
===>rt_ioctl_giwscan. 24(24) BSS returned, data->length = 2955
===>rt_ioctl_giwscan. 21(21) BSS returned, data->length = 2593
===>rt_ioctl_giwscan. 28(28) BSS returned, data->length = 3512
===>rt_ioctl_giwscan. 31(31) BSS returned, data->length = 3816
===>rt_ioctl_giwscan. 32(32) BSS returned, data->length = 3932
exe[2947]: segfault at 5f ip 085642ae sp b6575a50 error 4 in chrome[8048000+20dc000]
exe[2958]: segfault at 1692e8c6 ip b6c174cb sp b64b5a48 error 6 in libstdc++.so.6.0.13[b6bc1000+e8000]
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
===>rt_ioctl_giwscan. 29(29) BSS returned, data->length = 3614
wlan0: no IPv6 routers present
===>rt_ioctl_giwscan. 30(30) BSS returned, data->length = 3706
===>rt_ioctl_giwscan. 22(22) BSS returned, data->length = 2758
===>rt_ioctl_giwscan. 33(33) BSS returned, data->length = 4063
===>rt_ioctl_giwscan. 29(29) BSS returned, data->length = 3631
===>rt_ioctl_giwscan. 30(30) BSS returned, data->length = 3633NOTE: I load eeepc-laptop via rc.local to save time. I don't have any other hardware issues that I can think of.
Offline
Got it. I tried booting with MOD_AUTOLOAD set to yes, and it was working fine. Looks like I needed to specify some more modules in my list.
Offline