You are not logged in.

#1 2003-09-15 08:45:30

kakabaratruskia
Member
From: Santiago, Chile
Registered: 2003-08-24
Posts: 596

Can't get network up on startup.

I've tried everything, but I can't get my network connections to work during startup. I have to dhcpcd eth0 to get it working.
This is my rc.conf file:
#
# /etc/rc.conf - Main Configuration for Arch Linux
#

#
# Localization
#
# Note: HARDWARECLOCK is either "UTC" or "localtime"
#
KEYMAP=la-latin1
TIMEZONE=Chile/Continental
HARDWARECLOCK="UTC"

#
# Networking
#
HOSTNAME="selknam"

#
# Module to load at boot-up (in this order)
#   (prefix a module with a ! to disable it)
#
MODULES=(!usbserial !ide-scsi
scsi_hostadapter usb_storage 8139too tulip)

#
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
#   (prefix an interface in INTERFACES with a ! to disable it)
#
# Note: to use DHCP, set your interface to be "dhcp" (eth0="dhcp")
#
lo="lo 127.0.0.1"
eht0="dhcp"
eth1="eth1 192.168.0.1 netmask 255.255.255.0 broadcast 192.168.0.255"
INTERFACES=(lo eth0 eth1)

#
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
#   (prefix a route in ROUTES with a ! to disable it)
#
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)

#
# Daemons to start at boot-up (in this order)
#   (prefix a daemon with a ! to disable it)
#
DAEMONS=(!pcmcia network crond inetd)

# End of file


This is my modules.conf file.
#
# /etc/modules.conf
#
alias eth0 8139too
alias sound-slot-0 maestro3
alias eth1 tulip
probeall scsi_hostadapter usb-storage
# End of file


PLease help me.


And where were all the sportsmen who always pulled you though?
They're all resting down in Cornwall
writing up their memoirs for a paper-back edition
of the Boy Scout Manual.

Offline

#2 2003-09-15 09:13:18

Mork II
Member
From: Visby, Sweden
Registered: 2003-05-14
Posts: 87

Re: Can't get network up on startup.

You have a typo in your rc.conf that could be the problem:

eht0="dhcp" 

should be:

eth0="dhcp" 

Offline

#3 2003-09-15 12:28:24

red_over_blue
Member
Registered: 2003-07-19
Posts: 152

Re: Can't get network up on startup.

Also, does your Modules line actually span two lines?  This could also cause problems, since I don't know how Pacman handles these config files.

Try changing:

#
# Module to load at boot-up (in this order)
# (prefix a module with a ! to disable it)
#
MODULES=(!usbserial !ide-scsi
scsi_hostadapter usb_storage 8139too tulip)

to

#
# Module to load at boot-up (in this order)
# (prefix a module with a ! to disable it)
#
MODULES=(!usbserial !ide-scsi scsi_hostadapter usb_storage 8139too tulip)

Don't forget to post your PKGBUILD in your thread when you announce a new package in incoming.
see HERE for details

Offline

#4 2003-09-15 15:19:42

sarah31
Member
From: Middle of Canada
Registered: 2002-08-20
Posts: 2,975
Website

Re: Can't get network up on startup.

as well if you are going through a router or gateway you should remove the exclamation point (comment) from in fron of the gateway array.


AKA uknowme

I am not your friend

Offline

#5 2003-09-15 16:12:56

kakabaratruskia
Member
From: Santiago, Chile
Registered: 2003-08-24
Posts: 596

Re: Can't get network up on startup.

thanks a lot!!!. And, that about two lines is not a problem, really it's one line, but it didn't fit here.


And where were all the sportsmen who always pulled you though?
They're all resting down in Cornwall
writing up their memoirs for a paper-back edition
of the Boy Scout Manual.

Offline

#6 2007-01-11 03:43:26

mutlu_inek
Member
From: all over the place
Registered: 2006-11-18
Posts: 684

Re: Can't get network up on startup.

Please do not digg out four year (!) old threads.

Thanks.

Offline

Board footer

Powered by FluxBB