Arch Linux

Sander

Member

Registered: 2006-02-26

Posts: 138

Xorg: blank screen, mouse cursor only - ATI Radeon HD3450

Last friday, my old Nvidia card died (overheated, I think). I got a replacement today: an ATI HD3450 card by Asus (R600 series). This is an old PC with an AGP slot, so my options were unfortunately limited. I was looking for a Nvidia replacement originally, to avoid having to reconfigure stuff, but that turned out to be too hard. So I got an ATI card instead. I regret this decision now... it works fine in console mode, but I can't get it to work in X.

I've tried radeon and radeonhd drivers. I'm reluctant to try catalyst, seeing as they do not support the current kernel version (2.6.32) and I don't want to downgrade.

radeonhd (xf86-video-radeonhd) is just a disaster. When I try to start X, all I see is a screen which is mostly black, except for a garbled band of about 1/4th the screen height, mostly white with some random colours thrown in.

radeon (xf86-video-ati) doesn't work either. When X starts, all I see is the mouse cursor. And nothing else. Just a black screen with a mouse cursor. The funny thing is, it's all there, I just can't see it. When I tried "startxfce4", the cursor would change shapes when it was over window edges or text boxes. But they were invisible. Too bad.

When I run "startx" as root, I see a couple of twm windows (the default configuration, I normally don't use X as root), and I can interact with them, but it's as if the screen isn't refreshed properly. When I move a window, it isn't redrawn, but it was definitely moved, because when I enter text in it, the text appears at the new position. The 'vesa' driver works, but I can't use that for obvious reasons.

I have read the wiki article about ATI drivers and tried some of the things mentioned there (no xorg.conf, simple xorg.conf with some combinations of the sections mentioned, ...). I'm pretty sure the problem isn't KMS-related, because it's disabled by default with the 2.6.32 kernel.

What pisses me off the most is that I get no error messages whatsoever, so I haven't a clue what could be the problem. I'm working on getting some Xorg.0.log output in this thread ASAP.

Anybody have any idea what could cause this? I would really like to get this working soon. It would kinda suck if it turns out I've replaced an unusable graphics card with another unusable graphics card.

If the radeonhd problem is easier to solve, then solutions for that are welcome as well. I just need a working driver that can handle compiz, and doesn't require me to downgrade my kernel.

EDIT: Xorg.0.log contents, enjoy!

X.Org X Server 1.7.5
Release Date: 2010-02-16
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.32-ARCH i686 
Current Operating System: Linux arch 2.6.32-ARCH #1 SMP PREEMPT Tue Feb 9 14:46:08 UTC 2010 i686
Kernel command line: root=/dev/sda6 ro vga=838 radeon.modeset=0
Build Date: 17 February 2010  07:52:42PM
 
Current version of pixman: 0.16.6
    Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Tue Mar  2 17:45:35 2010
(II) Loader magic: 0x81e4ca0
(II) Module ABI versions:
    X.Org ANSI C Emulation: 0.4
    X.Org Video Driver: 6.0
    X.Org XInput driver : 7.0
    X.Org Server Extension : 2.0
(++) using VT number 7

(--) PCI:*(0:1:0:0) 1002:95c6:1043:0028 ATI Technologies Inc RV620 LE AGP [Radeon HD 3450] rev 0, Mem @ 0xe0000000/268435456, 0xf9000000/65536, I/O @ 0x00009000/256, BIOS @ 0x????????/131072
(==) Using default built-in configuration (30 lines)
(==) --- Start of built-in configuration ---
    Section "Device"
        Identifier    "Builtin Default ati Device 0"
        Driver    "ati"
    EndSection
    Section "Screen"
        Identifier    "Builtin Default ati Screen 0"
        Device    "Builtin Default ati Device 0"
    EndSection
    Section "Device"
        Identifier    "Builtin Default vesa Device 0"
        Driver    "vesa"
    EndSection
    Section "Screen"
        Identifier    "Builtin Default vesa Screen 0"
        Device    "Builtin Default vesa Device 0"
    EndSection
    Section "Device"
        Identifier    "Builtin Default fbdev Device 0"
        Driver    "fbdev"
    EndSection
    Section "Screen"
        Identifier    "Builtin Default fbdev Screen 0"
        Device    "Builtin Default fbdev Device 0"
    EndSection
    Section "ServerLayout"
        Identifier    "Builtin Default Layout"
        Screen    "Builtin Default ati Screen 0"
        Screen    "Builtin Default vesa Screen 0"
        Screen    "Builtin Default fbdev Screen 0"
    EndSection
(==) --- End of built-in configuration ---
(==) ServerLayout "Builtin Default Layout"
(**) |-->Screen "Builtin Default ati Screen 0" (0)
(**) |   |-->Monitor "<default monitor>"
(**) |   |-->Device "Builtin Default ati Device 0"
(==) No monitor specified for screen "Builtin Default ati Screen 0".
    Using a default monitor configuration.
(**) |-->Screen "Builtin Default vesa Screen 0" (1)
(**) |   |-->Monitor "<default monitor>"
(**) |   |-->Device "Builtin Default vesa Device 0"
(==) No monitor specified for screen "Builtin Default vesa Screen 0".
    Using a default monitor configuration.
(**) |-->Screen "Builtin Default fbdev Screen 0" (2)
(**) |   |-->Monitor "<default monitor>"
(**) |   |-->Device "Builtin Default fbdev Device 0"
(==) No monitor specified for screen "Builtin Default fbdev Screen 0".
    Using a default monitor configuration.
(==) Automatically adding devices
(==) Automatically enabling devices
(==) FontPath set to:
    /usr/share/fonts/misc,
    /usr/share/fonts/100dpi:unscaled,
    /usr/share/fonts/75dpi:unscaled,
    /usr/share/fonts/TTF,
    /usr/share/fonts/Type1
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) Cannot locate a core pointer device.
(II) Cannot locate a core keyboard device.
(II) The server relies on HAL to provide the list of input devices.
    If no devices become available, reconfigure HAL or disable AutoAddDevices.
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
    compiled for 1.7.5, module version = 1.0.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
    compiled for 1.7.5, module version = 1.0.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions/libglx.so
(II) Module glx: vendor="X.Org Foundation"
    compiled for 1.7.5, module version = 1.0.0
    ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions/libdri.so
(II) Module dri: vendor="X.Org Foundation"
    compiled for 1.7.5, module version = 1.0.0
    ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
    compiled for 1.7.5, module version = 1.1.0
    ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "ati"
(II) Loading /usr/lib/xorg/modules/drivers/ati_drv.so
(II) Module ati: vendor="X.Org Foundation"
    compiled for 1.7.3.902, module version = 6.12.4
    Module class: X.Org Video Driver
    ABI class: X.Org Video Driver, version 6.0
(II) LoadModule: "radeon"
(II) Loading /usr/lib/xorg/modules/drivers/radeon_drv.so
(II) Module radeon: vendor="X.Org Foundation"
    compiled for 1.7.3.902, module version = 6.12.4
    Module class: X.Org Video Driver
    ABI class: X.Org Video Driver, version 6.0
(II) LoadModule: "vesa"
(WW) Warning, couldn't open module vesa
(II) UnloadModule: "vesa"
(EE) Failed to load module "vesa" (module does not exist, 0)
(II) LoadModule: "fbdev"
(WW) Warning, couldn't open module fbdev
(II) UnloadModule: "fbdev"
(EE) Failed to load module "fbdev" (module does not exist, 0)
(II) RADEON: Driver for ATI Radeon chipsets:
    ATI Radeon Mobility X600 (M24) 3150 (PCIE), ATI FireMV 2400 (PCI),
    ATI Radeon Mobility X300 (M24) 3152 (PCIE),
    ATI FireGL M24 GL 3154 (PCIE), ATI Radeon X600 (RV380) 3E50 (PCIE),
    ATI FireGL V3200 (RV380) 3E54 (PCIE), ATI Radeon IGP320 (A3) 4136,
    ATI Radeon IGP330/340/350 (A4) 4137, ATI Radeon 9500 AD (AGP),
    ATI Radeon 9500 AE (AGP), ATI Radeon 9600TX AF (AGP),
    ATI FireGL Z1 AG (AGP), ATI Radeon 9800SE AH (AGP),
    ATI Radeon 9800 AI (AGP), ATI Radeon 9800 AJ (AGP),
    ATI FireGL X2 AK (AGP), ATI Radeon 9600 AP (AGP),
    ATI Radeon 9600SE AQ (AGP), ATI Radeon 9600XT AR (AGP),
    ATI Radeon 9600 AS (AGP), ATI FireGL T2 AT (AGP), ATI Radeon 9650,
    ATI FireGL RV360 AV (AGP), ATI Radeon 7000 IGP (A4+) 4237,
    ATI Radeon 8500 AIW BB (AGP), ATI Radeon 8500 AIW BC (AGP),
    ATI Radeon IGP320M (U1) 4336, ATI Radeon IGP330M/340M/350M (U2) 4337,
    ATI Radeon Mobility 7000 IGP 4437, ATI Radeon 9000/PRO If (AGP/PCI),
    ATI Radeon 9000 Ig (AGP/PCI), ATI Radeon X800 (R420) JH (AGP),
    ATI Radeon X800PRO (R420) JI (AGP),
    ATI Radeon X800SE (R420) JJ (AGP), ATI Radeon X800 (R420) JK (AGP),
    ATI Radeon X800 (R420) JL (AGP), ATI FireGL X3 (R420) JM (AGP),
    ATI Radeon Mobility 9800 (M18) JN (AGP),
    ATI Radeon X800 SE (R420) (AGP), ATI Radeon X800XT (R420) JP (AGP),
    ATI Radeon X800 VE (R420) JT (AGP), ATI Radeon X850 (R480) (AGP),
    ATI Radeon X850 XT (R480) (AGP), ATI Radeon X850 SE (R480) (AGP),
    ATI Radeon X850 PRO (R480) (AGP), ATI Radeon X850 XT PE (R480) (AGP),
    ATI Radeon Mobility M7 LW (AGP),
    ATI Mobility FireGL 7800 M7 LX (AGP),
    ATI Radeon Mobility M6 LY (AGP), ATI Radeon Mobility M6 LZ (AGP),
    ATI FireGL Mobility 9000 (M9) Ld (AGP),
    ATI Radeon Mobility 9000 (M9) Lf (AGP),
    ATI Radeon Mobility 9000 (M9) Lg (AGP), ATI Radeon 9700 Pro ND (AGP),
    ATI Radeon 9700/9500Pro NE (AGP), ATI Radeon 9600TX NF (AGP),
    ATI FireGL X1 NG (AGP), ATI Radeon 9800PRO NH (AGP),
    ATI Radeon 9800 NI (AGP), ATI FireGL X2 NK (AGP),
    ATI Radeon 9800XT NJ (AGP),
    ATI Radeon Mobility 9600/9700 (M10/M11) NP (AGP),
    ATI Radeon Mobility 9600 (M10) NQ (AGP),
    ATI Radeon Mobility 9600 (M11) NR (AGP),
    ATI Radeon Mobility 9600 (M10) NS (AGP),
    ATI FireGL Mobility T2 (M10) NT (AGP),
    ATI FireGL Mobility T2e (M11) NV (AGP), ATI Radeon QD (AGP),
    ATI Radeon QE (AGP), ATI Radeon QF (AGP), ATI Radeon QG (AGP),
    ATI FireGL 8700/8800 QH (AGP), ATI Radeon 8500 QL (AGP),
    ATI Radeon 9100 QM (AGP), ATI Radeon 7500 QW (AGP/PCI),
    ATI Radeon 7500 QX (AGP/PCI), ATI Radeon VE/7000 QY (AGP/PCI),
    ATI Radeon VE/7000 QZ (AGP/PCI), ATI ES1000 515E (PCI),
    ATI Radeon Mobility X300 (M22) 5460 (PCIE),
    ATI Radeon Mobility X600 SE (M24C) 5462 (PCIE),
    ATI FireGL M22 GL 5464 (PCIE), ATI Radeon X800 (R423) UH (PCIE),
    ATI Radeon X800PRO (R423) UI (PCIE),
    ATI Radeon X800LE (R423) UJ (PCIE),
    ATI Radeon X800SE (R423) UK (PCIE),
    ATI Radeon X800 XTP (R430) (PCIE), ATI Radeon X800 XL (R430) (PCIE),
    ATI Radeon X800 SE (R430) (PCIE), ATI Radeon X800 (R430) (PCIE),
    ATI FireGL V7100 (R423) (PCIE), ATI FireGL V5100 (R423) UQ (PCIE),
    ATI FireGL unknown (R423) UR (PCIE),
    ATI FireGL unknown (R423) UT (PCIE),
    ATI Mobility FireGL V5000 (M26) (PCIE),
    ATI Mobility FireGL V5000 (M26) (PCIE),
    ATI Mobility Radeon X700 XL (M26) (PCIE),
    ATI Mobility Radeon X700 (M26) (PCIE),
    ATI Mobility Radeon X700 (M26) (PCIE),
    ATI Radeon X550XTX 5657 (PCIE), ATI Radeon 9100 IGP (A5) 5834,
    ATI Radeon Mobility 9100 IGP (U3) 5835,
    ATI Radeon XPRESS 200 5954 (PCIE),
    ATI Radeon XPRESS 200M 5955 (PCIE), ATI Radeon 9250 5960 (AGP),
    ATI Radeon 9200 5961 (AGP), ATI Radeon 9200 5962 (AGP),
    ATI Radeon 9200SE 5964 (AGP), ATI FireMV 2200 (PCI),
    ATI ES1000 5969 (PCI), ATI Radeon XPRESS 200 5974 (PCIE),
    ATI Radeon XPRESS 200M 5975 (PCIE),
    ATI Radeon XPRESS 200 5A41 (PCIE),
    ATI Radeon XPRESS 200M 5A42 (PCIE),
    ATI Radeon XPRESS 200 5A61 (PCIE),
    ATI Radeon XPRESS 200M 5A62 (PCIE),
    ATI Radeon X300 (RV370) 5B60 (PCIE),
    ATI Radeon X600 (RV370) 5B62 (PCIE),
    ATI Radeon X550 (RV370) 5B63 (PCIE),
    ATI FireGL V3100 (RV370) 5B64 (PCIE),
    ATI FireMV 2200 PCIE (RV370) 5B65 (PCIE),
    ATI Radeon Mobility 9200 (M9+) 5C61 (AGP),
    ATI Radeon Mobility 9200 (M9+) 5C63 (AGP),
    ATI Mobility Radeon X800 XT (M28) (PCIE),
    ATI Mobility FireGL V5100 (M28) (PCIE),
    ATI Mobility Radeon X800 (M28) (PCIE), ATI Radeon X850 5D4C (PCIE),
    ATI Radeon X850 XT PE (R480) (PCIE),
    ATI Radeon X850 SE (R480) (PCIE), ATI Radeon X850 PRO (R480) (PCIE),
    ATI unknown Radeon / FireGL (R480) 5D50 (PCIE),
    ATI Radeon X850 XT (R480) (PCIE),
    ATI Radeon X800XT (R423) 5D57 (PCIE),
    ATI FireGL V5000 (RV410) (PCIE), ATI Radeon X700 XT (RV410) (PCIE),
    ATI Radeon X700 PRO (RV410) (PCIE),
    ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X700 (RV410) (PCIE),
    ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X1800,
    ATI Mobility Radeon X1800 XT, ATI Mobility Radeon X1800,
    ATI Mobility FireGL V7200, ATI FireGL V7200, ATI FireGL V5300,
    ATI Mobility FireGL V7100, ATI Radeon X1800, ATI Radeon X1800,
    ATI Radeon X1800, ATI Radeon X1800, ATI Radeon X1800,
    ATI FireGL V7300, ATI FireGL V7350, ATI Radeon X1600, ATI RV505,
    ATI Radeon X1300/X1550, ATI Radeon X1550, ATI M54-GL,
    ATI Mobility Radeon X1400, ATI Radeon X1300/X1550,
    ATI Radeon X1550 64-bit, ATI Mobility Radeon X1300,
    ATI Mobility Radeon X1300, ATI Mobility Radeon X1300,
    ATI Mobility Radeon X1300, ATI Radeon X1300, ATI Radeon X1300,
    ATI RV505, ATI RV505, ATI FireGL V3300, ATI FireGL V3350,
    ATI Radeon X1300, ATI Radeon X1550 64-bit, ATI Radeon X1300/X1550,
    ATI Radeon X1600, ATI Radeon X1300/X1550, ATI Mobility Radeon X1450,
    ATI Radeon X1300/X1550, ATI Mobility Radeon X2300,
    ATI Mobility Radeon X2300, ATI Mobility Radeon X1350,
    ATI Mobility Radeon X1350, ATI Mobility Radeon X1450,
    ATI Radeon X1300, ATI Radeon X1550, ATI Mobility Radeon X1350,
    ATI FireMV 2250, ATI Radeon X1550 64-bit, ATI Radeon X1600,
    ATI Radeon X1650, ATI Radeon X1600, ATI Radeon X1600,
    ATI Mobility FireGL V5200, ATI Mobility Radeon X1600,
    ATI Radeon X1650, ATI Radeon X1650, ATI Radeon X1600,
    ATI Radeon X1300 XT/X1600 Pro, ATI FireGL V3400,
    ATI Mobility FireGL V5250, ATI Mobility Radeon X1700,
    ATI Mobility Radeon X1700 XT, ATI FireGL V5200,
    ATI Mobility Radeon X1700, ATI Radeon X2300HD,
    ATI Mobility Radeon HD 2300, ATI Mobility Radeon HD 2300,
    ATI Radeon X1950, ATI Radeon X1900, ATI Radeon X1950,
    ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
    ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
    ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
    ATI AMD Stream Processor, ATI Radeon X1900, ATI Radeon X1950,
    ATI RV560, ATI RV560, ATI Mobility Radeon X1900, ATI RV560,
    ATI Radeon X1950 GT, ATI RV570, ATI RV570, ATI FireGL V7400,
    ATI RV560, ATI Radeon X1650, ATI Radeon X1650, ATI RV560,
    ATI Radeon 9100 PRO IGP 7834, ATI Radeon Mobility 9200 IGP 7835,
    ATI Radeon X1200, ATI Radeon X1200, ATI Radeon X1200,
    ATI Radeon X1200, ATI Radeon X1200, ATI RS740, ATI RS740M, ATI RS740,
    ATI RS740M, ATI Radeon HD 2900 XT, ATI Radeon HD 2900 XT,
    ATI Radeon HD 2900 XT, ATI Radeon HD 2900 Pro, ATI Radeon HD 2900 GT,
    ATI FireGL V8650, ATI FireGL V8600, ATI FireGL V7600,
    ATI Radeon 4800 Series, ATI Radeon HD 4870 x2,
    ATI Radeon 4800 Series, ATI Radeon HD 4850 x2,
    ATI FirePro V8750 (FireGL), ATI FirePro V7760 (FireGL),
    ATI Mobility RADEON HD 4850, ATI Mobility RADEON HD 4850 X2,
    ATI Radeon 4800 Series, ATI FirePro RV770, AMD FireStream 9270,
    AMD FireStream 9250, ATI FirePro V8700 (FireGL),
    ATI Mobility RADEON HD 4870, ATI Mobility RADEON M98,
    ATI Radeon 4800 Series, ATI Radeon 4800 Series, ATI FirePro M7750,
    ATI M98, ATI M98, ATI M98, ATI Mobility Radeon HD 4650,
    ATI Radeon RV730 (AGP), ATI Mobility Radeon HD 4670,
    ATI FirePro M5750, ATI Radeon RV730 (AGP),
    ATI RV730XT [Radeon HD 4670], ATI RADEON E4600,
    ATI Radeon HD 4600 Series, ATI RV730 PRO [Radeon HD 4650],
    ATI FirePro V7750 (FireGL), ATI FirePro V5700 (FireGL),
    ATI FirePro V3750 (FireGL), ATI Mobility Radeon HD 4830,
    ATI Mobility Radeon HD 4850, ATI FirePro M7740, ATI RV740,
    ATI Radeon HD 4770, ATI Radeon HD 4700 Series, ATI Radeon HD 4770,
    ATI FirePro M5750, ATI RV610, ATI Radeon HD 2400 XT,
    ATI Radeon HD 2400 Pro, ATI Radeon HD 2400 PRO AGP, ATI FireGL V4000,
    ATI RV610, ATI Radeon HD 2350, ATI Mobility Radeon HD 2400 XT,
    ATI Mobility Radeon HD 2400, ATI RADEON E2400, ATI RV610,
    ATI FireMV 2260, ATI RV670, ATI Radeon HD3870,
    ATI Mobility Radeon HD 3850, ATI Radeon HD3850,
    ATI Mobility Radeon HD 3850 X2, ATI RV670,
    ATI Mobility Radeon HD 3870, ATI Mobility Radeon HD 3870 X2,
    ATI Radeon HD3870 X2, ATI FireGL V7700, ATI Radeon HD3850,
    ATI Radeon HD3690, AMD Firestream 9170, ATI Radeon HD 4550,
    ATI Radeon RV710, ATI Radeon RV710, ATI Radeon HD 4350,
    ATI Mobility Radeon 4300 Series, ATI Mobility Radeon 4500 Series,
    ATI Mobility Radeon 4500 Series, ATI FirePro RG220, ATI RV630,
    ATI Mobility Radeon HD 2600, ATI Mobility Radeon HD 2600 XT,
    ATI Radeon HD 2600 XT AGP, ATI Radeon HD 2600 Pro AGP,
    ATI Radeon HD 2600 XT, ATI Radeon HD 2600 Pro, ATI Gemini RV630,
    ATI Gemini Mobility Radeon HD 2600 XT, ATI FireGL V5600,
    ATI FireGL V3600, ATI Radeon HD 2600 LE,
    ATI Mobility FireGL Graphics Processor, ATI Radeon RV710,
    ATI Radeon HD 3470, ATI Mobility Radeon HD 3430,
    ATI Mobility Radeon HD 3400 Series, ATI Radeon HD 3450,
    ATI Radeon HD 3450, ATI Radeon HD 3430, ATI Radeon HD 3450,
    ATI FirePro V3700, ATI FireMV 2450, ATI FireMV 2260, ATI FireMV 2260,
    ATI Radeon HD 3600 Series, ATI Radeon HD 3650 AGP,
    ATI Radeon HD 3600 PRO, ATI Radeon HD 3600 XT,
    ATI Radeon HD 3600 PRO, ATI Mobility Radeon HD 3650,
    ATI Mobility Radeon HD 3670, ATI Mobility FireGL V5700,
    ATI Mobility FireGL V5725, ATI Radeon HD 3200 Graphics,
    ATI Radeon 3100 Graphics, ATI Radeon HD 3200 Graphics,
    ATI Radeon 3100 Graphics, ATI Radeon HD 3300 Graphics,
    ATI Radeon HD 3200 Graphics, ATI Radeon 3000 Graphics,
    ATI Radeon HD 4200, ATI Radeon 4100, ATI Mobility Radeon HD 4200,
    ATI Mobility Radeon 4100, ATI RS880
(II) Primary Device is: PCI 01@00:00:0
(II) RADEON(0): TOTO SAYS 00000000f9000000
(II) RADEON(0): MMIO registers at 0x00000000f9000000: size 64KB
(II) RADEON(0): PCI bus 1 card 0 func 0
(II) RADEON(0): Creating default Display subsection in Screen section
    "Builtin Default ati Screen 0" for depth/fbbpp 24/32
(==) RADEON(0): Depth 24, (--) framebuffer bpp 32
(II) RADEON(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
(==) RADEON(0): Default visual is TrueColor
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules/libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
    compiled for 1.7.5, module version = 0.1.0
    ABI class: X.Org Video Driver, version 6.0
(II) RADEON(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(==) RADEON(0): RGB weight 888
(II) RADEON(0): Using 8 bits per RGB (8 bit DAC)
(--) RADEON(0): Chipset: "ATI Radeon HD 3450" (ChipID = 0x95c6)
(--) RADEON(0): Linear framebuffer at 0x00000000e0000000
(II) RADEON(0): AGP card detected
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib/xorg/modules/libint10.so
(II) Module int10: vendor="X.Org Foundation"
    compiled for 1.7.5, module version = 1.0.0
    ABI class: X.Org Video Driver, version 6.0
(II) RADEON(0): initializing int10
(II) RADEON(0): Primary V_BIOS segment is: 0xc000
(II) RADEON(0): ATOM BIOS detected
(II) RADEON(0): ATOM BIOS Rom: 
    SubsystemVendorID: 0x1043 SubsystemID: 0x0028
    IOBaseAddress: 0x9000
    Filename: SV31552.bin 
    BIOS Bootup Message: 

95C6.10.88.0.19.AS02                    

                                    
(II) RADEON(0): Framebuffer space used by Firmware (kb): 20
(II) RADEON(0): Start of VRAM area used by Firmware: 0x1fffb000
(II) RADEON(0): AtomBIOS requests 20kB of VRAM scratch space
(II) RADEON(0): AtomBIOS VRAM scratch base: 0x1fffb000
(II) RADEON(0): Cannot get VRAM scratch space. Allocating in main memory instead
(II) RADEON(0): Default Engine Clock: 600000
(II) RADEON(0): Default Memory Clock: 400000
(II) RADEON(0): Maximum Pixel ClockPLL Frequency Output: 1200000
(II) RADEON(0): Minimum Pixel ClockPLL Frequency Output: 0
(II) RADEON(0): Maximum Pixel ClockPLL Frequency Input: 13500
(II) RADEON(0): Minimum Pixel ClockPLL Frequency Input: 1000
(II) RADEON(0): Maximum Pixel Clock: 400000
(II) RADEON(0): Reference Clock: 27000
drmOpenDevice: node name is /dev/dri/card0
drmOpenByBusid: Searching for BusID pci:0000:01:00.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 10, (OK)
drmOpenByBusid: drmOpenMinor returns 10
drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
(II) RADEON(0): [dri] Found DRI library version 1.3.0 and kernel module version 1.31.0
(==) RADEON(0): Page Flipping disabled on r5xx and newer chips.

(II) RADEON(0): Will not try to use DMA for Xv image transfers
(II) RADEON(0): Detected total video RAM=524288K, accessible=262144K (PCI BAR=262144K)
(--) RADEON(0): Mapped VideoRAM: 262144 kByte (64 bit DDR SDRAM)
(II) RADEON(0): Color tiling disabled
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Module "i2c" already built-in
(II) RADEON(0): ref_freq: 2700, min_out_pll: 64800, max_out_pll: 120000, min_in_pll: 100, max_in_pll: 1350, xclk: 40000, sclk: 600.000000, mclk: 400.000000
(II) RADEON(0): PLL parameters: rf=2700 rd=12 min=64800 max=120000; xclk=40000
Shared DDC line: 0 3
(II) RADEON(0): Output VGA-0 has no monitor section
(II) RADEON(0): I2C bus "VGA-0" initialized.
(II) RADEON(0): Output HDMI-0 has no monitor section
(II) RADEON(0): I2C bus "HDMI-0" initialized.
(II) RADEON(0): Output DVI-0 has no monitor section
(II) RADEON(0): I2C bus "DVI-0" initialized.
(II) RADEON(0): Port0:
  XRANDR name: VGA-0
  Connector: VGA
  CRT1: INTERNAL_KLDSCP_DAC1
  DDC reg: 0x7e40
(II) RADEON(0): Port1:
  XRANDR name: HDMI-0
  Connector: HDMI-A
  DFP1: INTERNAL_UNIPHY
  DDC reg: 0x7e60
(II) RADEON(0): Port2:
  XRANDR name: DVI-0
  Connector: DVI-I
  CRT2: INTERNAL_KLDSCP_DAC2
  DFP2: INTERNAL_KLDSCP_LVTMA
  DDC reg: 0x7e50
(II) RADEON(0): I2C device "VGA-0:ddc2" registered at address 0xA0.
Dac detection success
(II) RADEON(0): Output: VGA-0, Detected Monitor Type: 0
finished output detect: 0
(II) RADEON(0): I2C device "HDMI-0:ddc2" registered at address 0xA0.
(II) RADEON(0): Output: HDMI-0, Detected Monitor Type: 0
finished output detect: 1
(II) RADEON(0): I2C device "DVI-0:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "DVI-0:DDC control interface" registered at address 0x6E.
(II) RADEON(0): Output: DVI-0, Detected Monitor Type: 3
(II) RADEON(0): EDID data from the display on output: DVI-0 ----------------------
(II) RADEON(0): Manufacturer: AIC  Model: 23  Serial#: 673
(II) RADEON(0): Year: 2007  Week: 26
(II) RADEON(0): EDID Version: 1.3
(II) RADEON(0): Digital Display Input
(II) RADEON(0): Max Image Size [cm]: horiz.: 47  vert.: 30
(II) RADEON(0): Gamma: 2.20
(II) RADEON(0): DPMS capabilities: StandBy Suspend Off
(II) RADEON(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 
(II) RADEON(0): First detailed timing not preferred mode in violation of standard!
(II) RADEON(0): redX: 0.648 redY: 0.335   greenX: 0.282 greenY: 0.604
(II) RADEON(0): blueX: 0.150 blueY: 0.072   whiteX: 0.312 whiteY: 0.328
(II) RADEON(0): Supported established timings:
(II) RADEON(0): 720x400@70Hz
(II) RADEON(0): 640x480@60Hz
(II) RADEON(0): 640x480@67Hz
(II) RADEON(0): 640x480@72Hz
(II) RADEON(0): 640x480@75Hz
(II) RADEON(0): 800x600@56Hz
(II) RADEON(0): 800x600@60Hz
(II) RADEON(0): 800x600@72Hz
(II) RADEON(0): 800x600@75Hz
(II) RADEON(0): 832x624@75Hz
(II) RADEON(0): 1024x768@60Hz
(II) RADEON(0): 1024x768@70Hz
(II) RADEON(0): 1024x768@75Hz
(II) RADEON(0): 1280x1024@75Hz
(II) RADEON(0): 1152x864@75Hz
(II) RADEON(0): Manufacturer's mask: 0
(II) RADEON(0): Supported standard timings:
(II) RADEON(0): #0: hsize: 1280  vsize 960  refresh: 60  vid: 16513
(II) RADEON(0): #1: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
(II) RADEON(0): #2: hsize: 1280  vsize 720  refresh: 60  vid: 49281
(II) RADEON(0): #3: hsize: 1440  vsize 900  refresh: 60  vid: 149
(II) RADEON(0): #4: hsize: 1440  vsize 900  refresh: 75  vid: 3989
(II) RADEON(0): #5: hsize: 1680  vsize 1050  refresh: 60  vid: 179
(II) RADEON(0): Supported detailed timing:
(II) RADEON(0): clock: 119.0 MHz   Image Size:  470 x 300 mm
(II) RADEON(0): h_active: 1680  h_sync: 1728  h_sync_end 1760 h_blank_end 1840 h_border: 0
(II) RADEON(0): v_active: 1050  v_sync: 1053  v_sync_end 1059 v_blanking: 1080 v_border: 0
(II) RADEON(0): Serial No: 00673
(II) RADEON(0): Ranges: V min: 55 V max: 75 Hz, H min: 24 H max: 83 kHz, PixClock max 150 MHz
(II) RADEON(0): Monitor name: H-W22 DVI
(II) RADEON(0): EDID (in hex):
(II) RADEON(0):     00ffffffffffff0005232300a1020000
(II) RADEON(0):     1a110103802f1e78e837a0a655489a26
(II) RADEON(0):     125054bfef808140818081c09500950f
(II) RADEON(0):     b300010101017c2e90a0601a1e403020
(II) RADEON(0):     3600d62c1100001a000000ff00303036
(II) RADEON(0):     37330a20202020202020000000fd0037
(II) RADEON(0):     4b18530f000a202020202020000000fc
(II) RADEON(0):     00482d573232204456490a2020200061
finished output detect: 2
finished all detect
before xf86InitialConfiguration
Dac detection success
(II) RADEON(0): Output: VGA-0, Detected Monitor Type: 0
(II) RADEON(0): Output: HDMI-0, Detected Monitor Type: 0
(II) RADEON(0): Output: DVI-0, Detected Monitor Type: 3
(II) RADEON(0): EDID data from the display on output: DVI-0 ----------------------
(II) RADEON(0): Manufacturer: AIC  Model: 23  Serial#: 673
(II) RADEON(0): Year: 2007  Week: 26
(II) RADEON(0): EDID Version: 1.3
(II) RADEON(0): Digital Display Input
(II) RADEON(0): Max Image Size [cm]: horiz.: 47  vert.: 30
(II) RADEON(0): Gamma: 2.20
(II) RADEON(0): DPMS capabilities: StandBy Suspend Off
(II) RADEON(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 
(II) RADEON(0): First detailed timing not preferred mode in violation of standard!
(II) RADEON(0): redX: 0.648 redY: 0.335   greenX: 0.282 greenY: 0.604
(II) RADEON(0): blueX: 0.150 blueY: 0.072   whiteX: 0.312 whiteY: 0.328
(II) RADEON(0): Supported established timings:
(II) RADEON(0): 720x400@70Hz
(II) RADEON(0): 640x480@60Hz
(II) RADEON(0): 640x480@67Hz
(II) RADEON(0): 640x480@72Hz
(II) RADEON(0): 640x480@75Hz
(II) RADEON(0): 800x600@56Hz
(II) RADEON(0): 800x600@60Hz
(II) RADEON(0): 800x600@72Hz
(II) RADEON(0): 800x600@75Hz
(II) RADEON(0): 832x624@75Hz
(II) RADEON(0): 1024x768@60Hz
(II) RADEON(0): 1024x768@70Hz
(II) RADEON(0): 1024x768@75Hz
(II) RADEON(0): 1280x1024@75Hz
(II) RADEON(0): 1152x864@75Hz
(II) RADEON(0): Manufacturer's mask: 0
(II) RADEON(0): Supported standard timings:
(II) RADEON(0): #0: hsize: 1280  vsize 960  refresh: 60  vid: 16513
(II) RADEON(0): #1: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
(II) RADEON(0): #2: hsize: 1280  vsize 720  refresh: 60  vid: 49281
(II) RADEON(0): #3: hsize: 1440  vsize 900  refresh: 60  vid: 149
(II) RADEON(0): #4: hsize: 1440  vsize 900  refresh: 75  vid: 3989
(II) RADEON(0): #5: hsize: 1680  vsize 1050  refresh: 60  vid: 179
(II) RADEON(0): Supported detailed timing:
(II) RADEON(0): clock: 119.0 MHz   Image Size:  470 x 300 mm
(II) RADEON(0): h_active: 1680  h_sync: 1728  h_sync_end 1760 h_blank_end 1840 h_border: 0
(II) RADEON(0): v_active: 1050  v_sync: 1053  v_sync_end 1059 v_blanking: 1080 v_border: 0
(II) RADEON(0): Serial No: 00673
(II) RADEON(0): Ranges: V min: 55 V max: 75 Hz, H min: 24 H max: 83 kHz, PixClock max 150 MHz
(II) RADEON(0): Monitor name: H-W22 DVI
(II) RADEON(0): EDID (in hex):
(II) RADEON(0):     00ffffffffffff0005232300a1020000
(II) RADEON(0):     1a110103802f1e78e837a0a655489a26
(II) RADEON(0):     125054bfef808140818081c09500950f
(II) RADEON(0):     b300010101017c2e90a0601a1e403020
(II) RADEON(0):     3600d62c1100001a000000ff00303036
(II) RADEON(0):     37330a20202020202020000000fd0037
(II) RADEON(0):     4b18530f000a202020202020000000fc
(II) RADEON(0):     00482d573232204456490a2020200061
(II) RADEON(0): Panel infos found from DDC detailed: 1680x1050
(II) RADEON(0): EDID vendor "AIC", prod id 35
(II) RADEON(0): Output VGA-0 disconnected
(II) RADEON(0): Output HDMI-0 disconnected
(II) RADEON(0): Output DVI-0 connected
(II) RADEON(0): Using exact sizes for initial modes
(II) RADEON(0): Output DVI-0 using initial mode 1680x1050
(II) RADEON(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
after xf86InitialConfiguration
(==) RADEON(0): DPI set to (96, 96)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules/libfb.so
(II) Module fb: vendor="X.Org Foundation"
    compiled for 1.7.5, module version = 1.0.0
    ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(==) RADEON(0): Will attempt to use R6xx/R7xx EXA support if DRI is enabled.
(II) Loading sub module "exa"
(II) LoadModule: "exa"
(II) Loading /usr/lib/xorg/modules/libexa.so
(II) Module exa: vendor="X.Org Foundation"
    compiled for 1.7.5, module version = 2.5.0
    ABI class: X.Org Video Driver, version 6.0
(!!) RADEON(0): For information on using the multimedia capabilities
    of this adapter, please see http://gatos.sf.net.
(!!) RADEON(0): MergedFB support has been removed and replaced with xrandr 1.2 support
(--) Depth 24 pixmap format is 32 bpp
(II) RADEON(0): RADEONScreenInit e0000000 0 0
(II) RADEON(0): DIG0 transmitter: Coherent Mode enabled
Output DIG0 transmitter setup success
Blank CRTC 0 success
Disable CRTC 0 success
Disable CRTC memreq 0 success
Blank CRTC 1 success
Disable CRTC 1 success
Disable CRTC memreq 1 success
(==) RADEON(0): Using 24 bit depth buffer
mc fb loc is 00ff00e0
(II) RADEON(0): RADEONInitMemoryMap() : 
(II) RADEON(0):   mem_size         : 0x20000000
(II) RADEON(0):   MC_FB_LOCATION   : 0x00ff00e0
(II) RADEON(0):   MC_AGP_LOCATION  : 0x003f0000
(II) RADEON(0): Depth moves disabled by default
(II) RADEON(0): Allocating from a screen of 262144 kb
(II) RADEON(0): Will use 32 kb for hardware cursor 0 at offset 0x00b7c000
(II) RADEON(0): Will use 32 kb for hardware cursor 1 at offset 0x00b80000
(II) RADEON(0): Will use 11760 kb for front buffer at offset 0x00000000
(II) RADEON(0): Will use 11760 kb for back buffer at offset 0x00b84000
(II) RADEON(0): Will use 11760 kb for depth buffer at offset 0x01700000
(II) RADEON(0): Will use 112640 kb for textures at offset 0x0227c000
(II) RADEON(0): Will use 114192 kb for X Server offscreen at offset 0x0907c000
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 10, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 10, (OK)
drmOpenByBusid: Searching for BusID pci:0000:01:00.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 10, (OK)
drmOpenByBusid: drmOpenMinor returns 10
drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
(II) [drm] DRM interface version 1.3
(II) [drm] DRM open master succeeded.
(II) RADEON(0): [drm] Using the DRM lock SAREA also for drawables.
(II) RADEON(0): [drm] framebuffer handle = 0xe0000000
(II) RADEON(0): [drm] added 1 reserved context for kernel
(II) RADEON(0): X context handle = 0x1
(II) RADEON(0): [drm] installed DRM signal handler
(II) RADEON(0): [agp] Mode 0x1f00421b [AGP 0x10de/0x00e1; Card 0x1002/0x95c6 0x1043/0x0028]
(II) RADEON(0): [agp] 32768 kB allocated with handle 0x00000001
(II) RADEON(0): [agp] ring handle = 0xf0000000
(II) RADEON(0): [agp] Ring mapped at 0xb712c000
(II) RADEON(0): [agp] ring read ptr handle = 0xf0101000
(II) RADEON(0): [agp] Ring read ptr mapped at 0xb72fb000
(II) RADEON(0): [agp] vertex/indirect buffers handle = 0xf0102000
(II) RADEON(0): [agp] Vertex/indirect buffers mapped at 0xa6ebd000
(II) RADEON(0): [agp] GART texture map handle = 0xf0302000
(II) RADEON(0): [agp] GART Texture map mapped at 0xa523d000
(II) RADEON(0): [drm] register handle = 0x2f200000
(II) RADEON(0): [dri] Visual configs initialized
(II) RADEON(0): RADEONRestoreMemMapRegisters() : 
(II) RADEON(0):   MC_FB_LOCATION   : 0x00ff00e0 0x00ff00e0
(II) RADEON(0):   MC_AGP_LOCATION  : 0x003f0000
(==) RADEON(0): Backing store disabled
(II) RADEON(0): [DRI] installation complete
(II) RADEON(0): [drm] Added 32 65536 byte vertex/indirect buffers
(II) RADEON(0): [drm] Mapped 32 vertex/indirect buffers
(II) RADEON(0): [drm] dma control initialized, using IRQ 16
(II) RADEON(0): [drm] Initialized kernel GART heap manager, 29884416
(WW) RADEON(0): DRI init changed memory map, adjusting ...
(WW) RADEON(0):   MC_FB_LOCATION  was: 0x00ff00e0 is: 0x00ff00e0
(WW) RADEON(0):   MC_AGP_LOCATION was: 0x003f0000 is: 0x0000de00
(II) RADEON(0): RADEONRestoreMemMapRegisters() : 
(II) RADEON(0):   MC_FB_LOCATION   : 0x00ff00e0 0x00ff00e0
(II) RADEON(0):   MC_AGP_LOCATION  : 0x0000de00
(II) RADEON(0): Direct rendering enabled
(II) RADEON(0): Setting EXA maxPitchBytes
(II) EXA(0): Offscreen pixmap area of 116932608 bytes
(II) EXA(0): Driver registered support for the following operations:
(II)         Solid
(II)         Copy
(II)         Composite (RENDER acceleration)
(II) RADEON(0): Acceleration enabled
(==) RADEON(0): DPMS enabled
(==) RADEON(0): Silken mouse enabled
(II) RADEON(0): Set up textured video
Output CRT1 disable success
(II) RADEON(0): DIG0 transmitter: Coherent Mode enabled
Output DIG0 transmitter setup success
(II) RADEON(0): DIG0 transmitter: Coherent Mode enabled
Output DIG0 transmitter setup success
Blank CRTC 0 success
Disable CRTC 0 success
Disable CRTC memreq 0 success
Blank CRTC 1 success
Disable CRTC 1 success
Disable CRTC memreq 1 success
(II) RADEON(0): DIG0 transmitter: Coherent Mode enabled
Output DIG0 transmitter setup success
Blank CRTC 0 success
Disable CRTC 0 success
Disable CRTC memreq 0 success
Mode 1680x1050 - 1840 1080 9
(II) RADEON(0): RADEONRestoreMemMapRegisters() : 
(II) RADEON(0):   MC_FB_LOCATION   : 0x00ff00e0 0x00ff00e0
(II) RADEON(0):   MC_AGP_LOCATION  : 0x0000de00
freq: 119000000
best_freq: 119000000
best_feedback_div: 119
best_ref_div: 3
best_post_div: 9
(II) RADEON(0): crtc(0) Clock: mode 119000, PLL 119000
(II) RADEON(0): crtc(0) PLL  : refdiv 3, fbdiv 0x77(119), pdiv 9
Set CRTC 0 PLL success
Set CRTC Timing success
Set CRTC 0 Overscan success
Not using RMX
scaler 0 setup success
Set CRTC 0 Source success
crtc 0 YUV disable setup success
(II) RADEON(0): DIG0 transmitter: Coherent Mode enabled
Output DIG0 transmitter setup success
Output DIG2 encoder setup success
Output DIG2 encoder setup success
(II) RADEON(0): DIG0 transmitter: Coherent Mode enabled
Output DIG0 transmitter setup success
(II) RADEON(0): DIG0 transmitter: Coherent Mode enabled
Output DIG0 transmitter setup success
(II) RADEON(0): DIG0 transmitter: Coherent Mode enabled
Output DIG0 transmitter setup success
Enable CRTC memreq 0 success
Enable CRTC 0 success
Unblank CRTC 0 success
Output CRT1 disable success
(II) RADEON(0): DIG0 transmitter: Coherent Mode enabled
Output DIG0 transmitter setup success
Blank CRTC 1 success
Disable CRTC 1 success
Disable CRTC memreq 1 success
(II) RADEON(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(II) RADEON(0): DIG0 transmitter: Coherent Mode enabled
Output DIG0 transmitter setup success
Blank CRTC 0 success
Disable CRTC 0 success
Disable CRTC memreq 0 success
Mode 1680x1050 - 1840 1080 9
(II) RADEON(0): RADEONRestoreMemMapRegisters() : 
(II) RADEON(0):   MC_FB_LOCATION   : 0x00ff00e0 0x00ff00e0
(II) RADEON(0):   MC_AGP_LOCATION  : 0x0000de00
freq: 119000000
best_freq: 119000000
best_feedback_div: 119
best_ref_div: 3
best_post_div: 9
(II) RADEON(0): crtc(0) Clock: mode 119000, PLL 119000
(II) RADEON(0): crtc(0) PLL  : refdiv 3, fbdiv 0x77(119), pdiv 9
Set CRTC 0 PLL success
Set CRTC Timing success
Set CRTC 0 Overscan success
Not using RMX
scaler 0 setup success
Set CRTC 0 Source success
crtc 0 YUV disable setup success
(II) RADEON(0): DIG0 transmitter: Coherent Mode enabled
Output DIG0 transmitter setup success
Output DIG2 encoder setup success
Output DIG2 encoder setup success
(II) RADEON(0): DIG0 transmitter: Coherent Mode enabled
Output DIG0 transmitter setup success
(II) RADEON(0): DIG0 transmitter: Coherent Mode enabled
Output DIG0 transmitter setup success
(II) RADEON(0): DIG0 transmitter: Coherent Mode enabled
Output DIG0 transmitter setup success
Enable CRTC memreq 0 success
Enable CRTC 0 success
Unblank CRTC 0 success
(--) RandR disabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) AIGLX: Screen 0 is not DRI2 capable
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 11, (OK)
drmOpenByBusid: Searching for BusID pci:0000:01:00.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 11, (OK)
drmOpenByBusid: drmOpenMinor returns 11
drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
(II) AIGLX: enabled GLX_MESA_copy_sub_buffer
(II) AIGLX: enabled GLX_SGI_make_current_read
(II) AIGLX: enabled GLX_texture_from_pixmap with driver support
(II) AIGLX: Loaded and initialized /usr/lib/xorg/modules/dri/r600_dri.so
(II) GLX: Initialized DRI GL provider for screen 0
(II) RADEON(0): Setting screen physical size to 444 x 277
(II) config/hal: Adding input device Macintosh mouse button emulation
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
    compiled for 1.7.3, module version = 2.3.2
    Module class: X.Org XInput Driver
    ABI class: X.Org XInput driver, version 7.0
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event0"
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Found relative axes
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Configuring as mouse
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
(**) Macintosh mouse button emulation: (accel) acceleration profile 0
(II) Macintosh mouse button emulation: initialized for relative axes.
(II) config/hal: Adding input device PS2++ Logitech MX Mouse
(**) PS2++ Logitech MX Mouse: always reports core events
(**) PS2++ Logitech MX Mouse: Device: "/dev/input/event4"
(II) PS2++ Logitech MX Mouse: Found 12 mouse buttons
(II) PS2++ Logitech MX Mouse: Found scroll wheel(s)
(II) PS2++ Logitech MX Mouse: Found relative axes
(II) PS2++ Logitech MX Mouse: Found x and y relative axes
(II) PS2++ Logitech MX Mouse: Configuring as mouse
(**) PS2++ Logitech MX Mouse: YAxisMapping: buttons 4 and 5
(**) PS2++ Logitech MX Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "PS2++ Logitech MX Mouse" (type: MOUSE)
(**) PS2++ Logitech MX Mouse: (accel) keeping acceleration scheme 1
(**) PS2++ Logitech MX Mouse: (accel) acceleration profile 0
(II) PS2++ Logitech MX Mouse: initialized for relative axes.
(II) config/hal: Adding input device AT Translated Set 2 keyboard
(**) AT Translated Set 2 keyboard: always reports core events
(**) AT Translated Set 2 keyboard: Device: "/dev/input/event1"
(II) AT Translated Set 2 keyboard: Found keys
(II) AT Translated Set 2 keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Power Button
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event2"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Power Button
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event3"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) AIGLX: Suspending AIGLX clients for VT switch
(II) RADEON(0): DIG0 transmitter: Coherent Mode enabled
Output DIG0 transmitter setup success
Blank CRTC 0 success
Disable CRTC 0 success
Disable CRTC memreq 0 success
Blank CRTC 1 success
Disable CRTC 1 success
Disable CRTC memreq 1 success
(II) RADEON(0): RADEONRestoreMemMapRegisters() : 
(II) RADEON(0):   MC_FB_LOCATION   : 0x00ff00e0 0x00ff00e0
(II) RADEON(0):   MC_AGP_LOCATION  : 0x00000000
(II) RADEON(0): avivo_restore !
Enable CRTC memreq 0 success
Enable CRTC 0 success
Unblank CRTC 0 success

Another update: the card seems to work just fine under windows, so it is definitely a configuration or driver issue.

Last edited by Sander (2010-03-02 17:12:40)

---

You like cheese? You like peas? You'll love cheezy peas!

tss

Member

From: UIUC

Registered: 2008-08-27

Posts: 17

Website

Re: Xorg: blank screen, mouse cursor only - ATI Radeon HD3450

There are no obvious errors related to the xf86-video-ati driver in that log.  In fact, the log indicates 3D acceleration is enabled.  Are you using packages from AUR or testing?  If I recall correctly, xf86-video-ati from stable doesn't have 3D acceleration support for the R600 series enabled by default.  You might try using the package from stable if you aren't already.  3D support for R600 is experimental at this point.

A couple of notes:
  * xf86-video-ati is the correct driver. Do not use xf86-video-radeonhd.
  * Even though 3D support is experimental, it *should* work.  I have the same card and I've got it working.
  * Consider enabling KMS using the method linked to on the ATI wiki page.  That's what I've done and it works great, no X configuration necessary.  Note that the linked method isn't quite up to date, you'll have to read through the thread to find the relevant changes you need to make.
  * Have patience.   You will get it working eventually.  I know because I have the same card. :-p  It's a one time cost; once you have it figure out you'll be set until the card dies.

---

Code is everything I thought poetry was... Clean, expressive, urgent, all-encompassing. Fourteen lines can open up to fill the available universe.
Teach Yourself Programming | Learn To Ask Questions | Fight Lost Productivity

Sander

Member

Registered: 2006-02-26

Posts: 138

Re: Xorg: blank screen, mouse cursor only - ATI Radeon HD3450

Thanks for taking the time to reply
I'll give enabling KMS a try. What thread is it that you're talking about? Also should I follow the "early start" or "late start" instructions?

EDIT: I'm guessing you mean this one? http://bbs.archlinux.org/viewtopic.php?pid=613720

EDIT2:

I did the following:

For enabling KMS create a file in /etc/modprobe.d/ called radeon.conf with this content:

    options radeon modeset=1

... and behold, now I can actually see stuff

now I just have to get 3D acceleration to work again. I'll update soon.
for some reason my cursor seems to be stuck on "X" now... weird.

EDIT3:

I reenabled compiz-fusion, and now the screen turns white, for some reason. The expo effect works (albeit laggy), but it just shows 4 white, empty desktops. I guess this is sort of a different problem. I'm still researching it. The "options radeon modeset=1" thing helped me a lot further though, thanks!

EDIT4:

making further progress. Starting Compiz gives:

compiz (core) - Fatal: GLX_EXT_texture_from_pixmap is missing
compiz (core) - Error: Failed to manage screen: 0
compiz (core) - Fatal: No manageable screens found on display :0.0

And Xorg.0.log makes mention of:

(II) AIGLX: Screen 0 is not DRI2 capable
(II) AIGLX: Screen 0 is not DRI capable

I haven't googled this last bit yet, I'm getting to that now. Be back soon

EDIT5:

"Enabling KMS will make Xorg fall back to software rasterizing, at the cost of 3D performance. " <- is this still true at the moment? In that case, enabling KMS really isn't the solution I'm looking for. Back to square one

EDIT6:

Another clue from Xorg.0.log:

(EE) RADEON(0): [dri] RADEONDRIGetVersion failed because of a version mismatch.
[dri] radeon kernel module version is 2.0.0 but version 1.17.0 or newer is needed.
[dri] Disabling DRI.

So this is a DRI1 <-> DRI2 thing? I'm confused

EDIT7:

I found this, which says:

Your xf86-video-ati doesn't have support for KMS - you have to rebuild it against libdrm_radeon. This also means that you have to rebuild mesa against same new libdrm because mesa doesn't have KMS support without libdrm_radeon either.

Is this information applicable to my situation? No instructions on how to do this are provided, so I have no idea how to try it, or if it's worth trying at all.

EDIT8:

My abs tree was out of date, so I made some wrong assumptions. I'm going to recompile a few packages from ABS and see where that gets me.

Last edited by Sander (2010-03-02 19:50:01)

---

You like cheese? You like peas? You'll love cheezy peas!

tss

Member

From: UIUC

Registered: 2008-08-27

Posts: 17

Website

Re: Xorg: blank screen, mouse cursor only - ATI Radeon HD3450

"Enabling KMS will make Xorg fall back to software rasterizing, at the cost of 3D performance. " <- is this still true at the moment? In that case, enabling KMS really isn't the solution I'm looking for. Back to square one

This is not true.  Software rasterization indicates that KMS was not set up correctly.  You will get 3D acceleration with KMS correctly configured.

Thanks for taking the time to reply
I'll give enabling KMS a try. What thread is it that you're talking about? Also should I follow the "early start" or "late start" instructions?

EDIT: I'm guessing you mean this one? http://bbs.archlinux.org/viewtopic.php?pid=613720

That thread is the one I meant. 

Your xf86-video-ati doesn't have support for KMS - you have to rebuild it against libdrm_radeon. This also means that you have to rebuild mesa against same new libdrm because mesa doesn't have KMS support without libdrm_radeon either.

Is this information applicable to my situation? No instructions on how to do this are provided, so I have no idea how to try it, or if it's worth trying at all.

Yes, this is a problem.  You have to modify a PKGBUILD or two and build/install the packages in the correct order.  I detail the right way to do everything below.

I used the following packages:
* kernel26-git: http://aur.archlinux.org/packages.php?ID=25304 (you must configure with CONFIG_DRM_RADEON=m. CONFIG_DRM_RADEON_KMS=y enables KMS by default.  you should be presented with a configuration menu when the package builds.  type '/' to search.)
* kernel26-firmware-git: http://aur.archlinux.org/packages.php?ID=25782
* radeon_ucode: http://aur.archlinux.org/packages.php?ID=33016
* libdrm-git: http://aur.archlinux.org/packages.php?ID=10254 (you must edit the PKGBUILD to enable radeon support, see below)
* glproto-git: http://aur.archlinux.org/packages.php?ID=18964
* dri2proto-git: http://aur.archlinux.org/packages.php?ID=19051
* libgl-git: http://aur.archlinux.org/packages.php?ID=19044 (this is out of date and requires a patch.  see my comment on the AUR page)
* mesa-git: http://aur.archlinux.org/packages.php?ID=8266 (you can reuse src/mesa from libgl-git, it clones the same repository)
* xf86-video-ati-git: http://aur.archlinux.org/packages.php?ID=15374 (you can reuse src/mesa from libgl-git)

libdrm-git PKGBUILD:

....
  sh autogen.sh --prefix=/usr \
                --enable-nouveau-experimental-api \
        --enable-udev || return 1
#                --enable-radeon-experimental-api
....

libdrm-git PKGBUILD modified:

....
  sh autogen.sh --prefix=/usr \
                --enable-radeon-experimental-api \
        --enable-udev || return 1
....

Install those packages in that order and add yourself to the video group.  Make sure that your grub configuration has an option to select the new kernel.  Also make sure all of your PKGBUILDs from AUR are up to date.  A week or two ago they were all wrong (as a noted above, one of them is still wrong and requires a patch).

I hope that helps.  Eventually Arch will support KMS for radeon by default, but the driver and the kernel need to go through another release or two.

Last edited by tss (2010-03-02 20:34:52)

---

Code is everything I thought poetry was... Clean, expressive, urgent, all-encompassing. Fourteen lines can open up to fill the available universe.
Teach Yourself Programming | Learn To Ask Questions | Fight Lost Productivity

Sander

Member

Registered: 2006-02-26

Posts: 138

Re: Xorg: blank screen, mouse cursor only - ATI Radeon HD3450

I have recompiled libdrm from ABS with --enable-radeon-experimental-api added to the PKGBUILD. I am now recompiling mesa, also from ABS. I'm a bit reluctant to use the -git-versions of the packages you mentioned. Is that strictly necessary?

---

You like cheese? You like peas? You'll love cheezy peas!

tss

Member

From: UIUC

Registered: 2008-08-27

Posts: 17

Website

Re: Xorg: blank screen, mouse cursor only - ATI Radeon HD3450

I have recompiled libdrm from ABS with --enable-radeon-experimental-api added to the PKGBUILD. I am now recompiling mesa, also from ABS. I'm a bit reluctant to use the -git-versions of the packages you mentioned. Is that strictly necessary?

It's not strictly necessary no.  Definitely stick with ABS if you are more comfortable with that.  I will still help you debug errors.  I just posted the above because I know 100% that it works.

---

Code is everything I thought poetry was... Clean, expressive, urgent, all-encompassing. Fourteen lines can open up to fill the available universe.
Teach Yourself Programming | Learn To Ask Questions | Fight Lost Productivity

Sander

Member

Registered: 2006-02-26

Posts: 138

Re: Xorg: blank screen, mouse cursor only - ATI Radeon HD3450

Right, I recompiled libdrm from abs with --enable-radeon-experimental-api and installed it, then I recompiled mesa and xf86-video-ati, and installed all the resulting packages.
... to no avail. I still find the same 'version mismatch' message in Xorg.0.log

What am I missing? I followed the instructions from the wiki article, but I suppose they are out of date as well, then? Are there any other packages I need to recompile? Maybe I didn't recompile them correctly?

I guess I could try following your guide to the letter, but then I'd be using -git packages, which I don't quite like the idea of.

Either way, at the moment it's looking a lot like that's the only remaining option. Or I could downgrade the kernel anyway and give catalyst a try... which I don't like much, either.

Thank you for your help and patience, at any rate. This is the first ATI card I've ever bought so I'm pretty new to all of this. I'm thinking it's more than likely going to be the last, as well

---

You like cheese? You like peas? You'll love cheezy peas!

tss

Member

From: UIUC

Registered: 2008-08-27

Posts: 17

Website

Re: Xorg: blank screen, mouse cursor only - ATI Radeon HD3450

Right, I recompiled libdrm from abs with --enable-radeon-experimental-api and installed it, then I recompiled mesa and xf86-video-ati, and installed all the resulting packages.
... to no avail. I still find the same 'version mismatch' message in Xorg.0.log

What am I missing? I followed the instructions from the wiki article, but I suppose they are out of date as well, then? Are there any other packages I need to recompile? Maybe I didn't recompile them correctly?

I guess I could try following your guide to the letter, but then I'd be using -git packages, which I don't quite like the idea of.

One possible solution to this issue is documented on the Xorg wiki: http://www.x.org/wiki/radeonBuildHowTo# … MSproblems.  Make sure the module they talk about is loaded.

Also, it's possible mesa from ABS is not built with dri support for radeon.  See the mesa-git PKGBUILD: http://aur.archlinux.org/packages/mesa- … t/PKGBUILD.  The relevant part is:

....
  ./autogen.sh --prefix=/usr \
    --with-dri-driverdir=/usr/lib/xorg/modules/dri \
    --with-dri-drivers=swrast,radeon,r200,r300,r600,i810,i915,i965,unichrome,mach64,mga,r128,savage,sis,tdfx \
    --disable-gallium-intel \
    --enable-glx-tls \
    --with-driver=dri \
    --enable-xcb \
    --disable-glut --disable-gallium || return 1
....

You may have to modify the mesa PKGBUILD from ABS.

Either way, at the moment it's looking a lot like that's the only remaining option. Or I could downgrade the kernel anyway and give catalyst a try... which I don't like much, either.

Thank you for your help and patience, at any rate. This is the first ATI card I've ever bought so I'm pretty new to all of this. I'm thinking it's more than likely going to be the last, as well

Don't give up yet!  The fact is that both Nvidia and ATI don't support open source drivers like they should.  True, Nvidia's proprietary Linux drivers are better than ATI's proprietary Linux drivers, but it's nice to be able to use free software.  The good news is that the R600 series from ATI is getting to the point where it is well supported in the open source community.  KMS support will be standard in the kernel soon and power management options are on the way.

Of course, if you do gaming or video editing or anything where graphics performance is absolutely critical, Nvidia with the proprietary driver is the best choice.

Last edited by tss (2010-03-02 21:18:48)

---

Code is everything I thought poetry was... Clean, expressive, urgent, all-encompassing. Fourteen lines can open up to fill the available universe.
Teach Yourself Programming | Learn To Ask Questions | Fight Lost Productivity

Sander

Member

Registered: 2006-02-26

Posts: 138

Re: Xorg: blank screen, mouse cursor only - ATI Radeon HD3450

Thanks. I have been trying to get this to work all day, so I need a break now
Tomorrow I'm going to either try what you said, or go out and buy an Nvidia card, and sell the ATI one. The latter option is starting to look more and more attractive... it'll depend on how adventurous I'm feeling

Thanks again, I really appreciate it.

---

You like cheese? You like peas? You'll love cheezy peas!