You are not logged in.
Printer: hp psc 1350
I have hplip installed as well as cups and cups is started at boot.
Usb hardware works (mouse, webcam, phone link) until I turn on the printer.
After a few minutes the mouse no longer works and I get the following message when dmesg is run:
chromium[22036]: segfault at 10 ip 000000000105612d sp 00007fff00894320 error 4 in chromium[400000+25e4000]
chromium[22148]: segfault at 10 ip 000000000105612d sp 00007fff00894320 error 4 in chromium[400000+25e4000]
INFO: task scsi_eh_10:21277 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
scsi_eh_10 D ffff880216f51c80 0 21277 2 0x00000000
ffff8802157d3cc0 0000000000000046 0000000000000082 ffff88000888fa78
ffff8802157d3df8 00000000000052c0 ffff88000888fa00 ffffffff00000001
0000000000000008 ffff8802157d3fd8 ffff8802157d2000 ffff8802157d2000
Call Trace:
[<ffffffff8135b19d>] schedule_timeout+0x22d/0x360
[<ffffffffa0d014c2>] ? ohci_urb_dequeue+0x72/0x120 [ohci_hcd]
[<ffffffff8135a015>] wait_for_common+0xc5/0x160
[<ffffffff8104d700>] ? default_wake_function+0x0/0x10
[<ffffffff8135a148>] wait_for_completion+0x18/0x20
[<ffffffffa0dcdaac>] command_abort+0x7c/0xa0 [usb_storage]
[<ffffffffa00054fc>] scsi_error_handler+0x3dc/0x460 [scsi_mod]
[<ffffffffa0005120>] ? scsi_error_handler+0x0/0x460 [scsi_mod]
[<ffffffff81072d0e>] kthread+0x8e/0xa0
[<ffffffff8100ade4>] kernel_thread_helper+0x4/0x10
[<ffffffff81072c80>] ? kthread+0x0/0xa0
[<ffffffff8100ade0>] ? kernel_thread_helper+0x0/0x10
INFO: task hald-addon-stor:21351 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
hald-addon-st D ffff880210d6a3a0 0 21351 3982 0x00000000
ffff880210ca1868 0000000000000082 ffff880210ca17c8 ffff880216f563f8
ffff880008995c40 ffff880216f563c0 ffff8800089952c0 0000000000000000
00000000000152c0 ffff880210ca1fd8 ffff880210ca0000 ffff880210ca0000
Call Trace:
[<ffffffff8135b19d>] schedule_timeout+0x22d/0x360
[<ffffffff811b7adf>] ? blk_peek_request+0x13f/0x220
[<ffffffff8135a015>] wait_for_common+0xc5/0x160
[<ffffffff8104d700>] ? default_wake_function+0x0/0x10
[<ffffffff811b875d>] ? __generic_unplug_device+0x2d/0x40
[<ffffffff8135a148>] wait_for_completion+0x18/0x20
[<ffffffff811bdf49>] blk_execute_rq+0x89/0xf0
[<ffffffff811b964d>] ? blk_get_request+0x6d/0x90
[<ffffffffa0008007>] scsi_execute+0xf7/0x160 [scsi_mod]
[<ffffffffa0008115>] scsi_execute_req+0xa5/0x1c0 [scsi_mod]
[<ffffffffa0052714>] sd_revalidate_disk+0x134/0x1a60 [sd_mod]
[<ffffffffa00082d4>] ? scsi_test_unit_ready+0xa4/0x1e0 [scsi_mod]
[<ffffffff81150aba>] ? __invalidate_device+0x4a/0x60
[<ffffffff81150000>] ? bio_copy_user_iov+0x3e0/0x4e0
[<ffffffff81150cc0>] check_disk_change+0x60/0x70
[<ffffffffa005216a>] sd_open+0x8a/0x170 [sd_mod]
[<ffffffff81151dec>] __blkdev_get+0xcc/0x420
[<ffffffff81152150>] ? blkdev_open+0x0/0xc0
[<ffffffff8115214b>] blkdev_get+0xb/0x10
[<ffffffff811521bc>] blkdev_open+0x6c/0xc0
[<ffffffff811203a8>] __dentry_open+0x148/0x3f0
[<ffffffff811a0c5a>] ? security_inode_permission+0x1a/0x20
[<ffffffff81120754>] nameidata_to_filp+0x54/0x70
[<ffffffff81130e10>] do_filp_open+0x950/0xd80
[<ffffffff81122112>] ? do_sync_read+0xd2/0x110
[<ffffffff81120144>] do_sys_open+0x64/0x130
[<ffffffff8112023b>] sys_open+0x1b/0x20
[<ffffffff81009fc2>] system_call_fastpath+0x16/0x1bI was trying to set up the printer via localhost:631 to see if that would work (it didn't) since using hp-toolbox caused a lock up.
Thanks in advance for your help.
Arch64
KDE4 user
Offline