Arch Linux

fincan

Member

Registered: 2010-07-13

Posts: 27

Samsung Sata Dvdwr and Kernel Panic

I bought a new sata dvdwr(samsung sata dvdwr sh-s223c) but when I plug the new dvdwr, at boot kernel panic appears. well I try to plug the device from ICH8 chip of the motherboard and my system works on fakeraid0 on the same chip. On the other hand if I plug the device from jmicron onboard controller, there is no problem.

BTW there is no problem with my ubuntu install.

dmseg | grep -i scsi

[fincan@kahve ~]$ dmesg | grep -i scsi
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
SCSI subsystem initialized
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
scsi6 : ahci
scsi7 : ahci
scsi 0:0:0:0: Direct-Access     ATA      WDC WD2500KS-00M 02.0 PQ: 0 ANSI: 5
scsi 1:0:0:0: Direct-Access     ATA      WDC WD2500KS-00M 02.0 PQ: 0 ANSI: 5
scsi 2:0:0:0: Direct-Access     ATA      SAMSUNG HD080HJ  ZH10 PQ: 0 ANSI: 5
scsi 7:0:0:0: CD-ROM            TSSTcorp CDDVDW SH-S223C  SB02 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 47x/94x writer dvd-ram cd/rw xa/form2 cdda tray
sr 7:0:0:0: Attached scsi CD-ROM sr0
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 2:0:0:0: [sdc] Attached SCSI disk
sd 0:0:0:0: [sda] Attached SCSI disk
scsi8 : pata_jmicron
scsi9 : pata_jmicron

dmseg | grep -i pci

[fincan@kahve ~]$ dmesg | grep -i pci
Allocating PCI resources starting at 7ff00000 (gap: 7ff00000:60100000)
ACPI: bus type pci registered
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
PCI: Using configuration type 1 for base access
PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci_root PNP0A08:00: host bridge window [io  0x0000-0x0cf7] (ignored)
pci_root PNP0A08:00: host bridge window [io  0x0d00-0xffff] (ignored)
pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
pci_root PNP0A08:00: host bridge window [mem 0x000c0000-0x000dffff] (ignored)
pci_root PNP0A08:00: host bridge window [mem 0x7ff00000-0xfebfffff] (ignored)
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:1a.0: reg 20: [io  0xff00-0xff1f]
pci 0000:00:1a.1: reg 20: [io  0xfe00-0xfe1f]
pci 0000:00:1a.7: reg 10: [mem 0xfdfff000-0xfdfff3ff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: PME# disabled
pci 0000:00:1b.0: reg 10: [mem 0xfdff4000-0xfdff7fff 64bit]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.2: PME# disabled
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: PME# disabled
pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.5: PME# disabled
pci 0000:00:1d.0: reg 20: [io  0xfd00-0xfd1f]
pci 0000:00:1d.1: reg 20: [io  0xfc00-0xfc1f]
pci 0000:00:1d.2: reg 20: [io  0xfb00-0xfb1f]
pci 0000:00:1d.7: reg 10: [mem 0xfdffe000-0xfdffe3ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: [io  0x0400-0x047f] claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: [io  0x0480-0x04bf] claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 00e0 (mask 000f)
pci 0000:00:1f.2: reg 10: [io  0xfa00-0xfa07]
pci 0000:00:1f.2: reg 14: [io  0xf900-0xf903]
pci 0000:00:1f.2: reg 18: [io  0xf800-0xf807]
pci 0000:00:1f.2: reg 1c: [io  0xf700-0xf703]
pci 0000:00:1f.2: reg 20: [io  0xf600-0xf61f]
pci 0000:00:1f.2: reg 24: [mem 0xfdffd000-0xfdffd7ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 10: [mem 0xfdffc000-0xfdffc0ff]
pci 0000:00:1f.3: reg 20: [io  0x0500-0x051f]
pci 0000:01:00.0: reg 10: [mem 0xfa000000-0xfaffffff]
pci 0000:01:00.0: reg 14: [mem 0xd0000000-0xdfffffff 64bit pref]
pci 0000:01:00.0: reg 1c: [mem 0xf8000000-0xf9ffffff 64bit]
pci 0000:01:00.0: reg 24: [io  0xbf00-0xbf7f]
pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:00:01.0:   bridge window [io  0xb000-0xbfff]
pci 0000:00:01.0:   bridge window [mem 0xf8000000-0xfbffffff]
pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
pci 0000:00:1c.0: PCI bridge to [bus 02-02]
pci 0000:00:1c.0:   bridge window [io  0xa000-0xafff]
pci 0000:00:1c.0:   bridge window [mem 0xfda00000-0xfdafffff]
pci 0000:00:1c.0:   bridge window [mem 0xfd700000-0xfd7fffff 64bit pref]
pci 0000:03:00.0: reg 10: [io  0x9e00-0x9eff]
pci 0000:03:00.0: reg 18: [mem 0xfd6ff000-0xfd6fffff 64bit]
pci 0000:03:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
pci 0000:03:00.0: supports D1 D2
pci 0000:03:00.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:03:00.0: PME# disabled
pci 0000:00:1c.2: PCI bridge to [bus 03-03]
pci 0000:00:1c.2:   bridge window [io  0x9000-0x9fff]
pci 0000:00:1c.2:   bridge window [mem 0xfd600000-0xfd6fffff]
pci 0000:00:1c.2:   bridge window [mem 0xfd500000-0xfd5fffff 64bit pref]
pci 0000:04:00.0: reg 10: [io  0xde00-0xdeff]
pci 0000:04:00.0: reg 18: [mem 0xfdeff000-0xfdefffff 64bit]
pci 0000:04:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
pci 0000:04:00.0: supports D1 D2
pci 0000:04:00.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:04:00.0: PME# disabled
pci 0000:00:1c.4: PCI bridge to [bus 04-04]
pci 0000:00:1c.4:   bridge window [io  0xd000-0xdfff]
pci 0000:00:1c.4:   bridge window [mem 0xfde00000-0xfdefffff]
pci 0000:00:1c.4:   bridge window [mem 0xfdd00000-0xfddfffff 64bit pref]
pci 0000:05:00.0: reg 24: [mem 0xfdcfe000-0xfdcfffff]
pci 0000:05:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
pci 0000:05:00.0: PME# supported from D3hot
pci 0000:05:00.0: PME# disabled
pci 0000:05:00.1: reg 10: [io  0xcf00-0xcf07]
pci 0000:05:00.1: reg 14: [io  0xce00-0xce03]
pci 0000:05:00.1: reg 18: [io  0xcd00-0xcd07]
pci 0000:05:00.1: reg 1c: [io  0xcc00-0xcc03]
pci 0000:05:00.1: reg 20: [io  0xcb00-0xcb0f]
pci 0000:00:1c.5: PCI bridge to [bus 05-05]
pci 0000:00:1c.5:   bridge window [io  0xc000-0xcfff]
pci 0000:00:1c.5:   bridge window [mem 0xfdc00000-0xfdcfffff]
pci 0000:00:1c.5:   bridge window [mem 0xfdb00000-0xfdbfffff 64bit pref]
pci 0000:06:02.0: reg 10: [mem 0xfd9ff000-0xfd9ff7ff]
pci 0000:06:02.0: reg 14: [mem 0xfd9f8000-0xfd9fbfff]
pci 0000:06:02.0: supports D1 D2
pci 0000:06:02.0: PME# supported from D0 D1 D2 D3hot
pci 0000:06:02.0: PME# disabled
pci 0000:00:1e.0: PCI bridge to [bus 06-06] (subtractive decode)
pci 0000:00:1e.0:   bridge window [io  0x8000-0x8fff]
pci 0000:00:1e.0:   bridge window [mem 0xfd900000-0xfd9fffff]
pci 0000:00:1e.0:   bridge window [mem 0xfd800000-0xfd8fffff 64bit pref]
pci 0000:00:1e.0:   bridge window [io  0x0000-0xffff] (subtractive decode)
pci 0000:00:1e.0:   bridge window [mem 0x00000000-0xffffffffffffffff] (subtractive decode)
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 4 5 *7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNK0] (IRQs *4 5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNK1] (IRQs 4 5 7 10 *11 14 15)
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
pci 0000:01:00.0: BAR 6: assigned [mem 0xfb000000-0xfb01ffff pref]
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:00:01.0:   bridge window [io  0xb000-0xbfff]
pci 0000:00:01.0:   bridge window [mem 0xf8000000-0xfbffffff]
pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
pci 0000:00:1c.0: PCI bridge to [bus 02-02]
pci 0000:00:1c.0:   bridge window [io  0xa000-0xafff]
pci 0000:00:1c.0:   bridge window [mem 0xfda00000-0xfdafffff]
pci 0000:00:1c.0:   bridge window [mem 0xfd700000-0xfd7fffff 64bit pref]
pci 0000:03:00.0: BAR 6: assigned [mem 0xfd500000-0xfd51ffff pref]
pci 0000:00:1c.2: PCI bridge to [bus 03-03]
pci 0000:00:1c.2:   bridge window [io  0x9000-0x9fff]
pci 0000:00:1c.2:   bridge window [mem 0xfd600000-0xfd6fffff]
pci 0000:00:1c.2:   bridge window [mem 0xfd500000-0xfd5fffff 64bit pref]
pci 0000:04:00.0: BAR 6: assigned [mem 0xfdd00000-0xfdd1ffff pref]
pci 0000:00:1c.4: PCI bridge to [bus 04-04]
pci 0000:00:1c.4:   bridge window [io  0xd000-0xdfff]
pci 0000:00:1c.4:   bridge window [mem 0xfde00000-0xfdefffff]
pci 0000:00:1c.4:   bridge window [mem 0xfdd00000-0xfddfffff 64bit pref]
pci 0000:05:00.0: BAR 6: assigned [mem 0xfdb00000-0xfdb0ffff pref]
pci 0000:00:1c.5: PCI bridge to [bus 05-05]
pci 0000:00:1c.5:   bridge window [io  0xc000-0xcfff]
pci 0000:00:1c.5:   bridge window [mem 0xfdc00000-0xfdcfffff]
pci 0000:00:1c.5:   bridge window [mem 0xfdb00000-0xfdbfffff 64bit pref]
pci 0000:00:1e.0: PCI bridge to [bus 06-06]
pci 0000:00:1e.0:   bridge window [io  0x8000-0x8fff]
pci 0000:00:1e.0:   bridge window [mem 0xfd900000-0xfd9fffff]
pci 0000:00:1e.0:   bridge window [mem 0xfd800000-0xfd8fffff 64bit pref]
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:1c.2: setting latency timer to 64
pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.4: setting latency timer to 64
pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.5: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 [io  0x0000-0xffff]
pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffffffffffff]
pci_bus 0000:01: resource 0 [io  0xb000-0xbfff]
pci_bus 0000:01: resource 1 [mem 0xf8000000-0xfbffffff]
pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
pci_bus 0000:02: resource 0 [io  0xa000-0xafff]
pci_bus 0000:02: resource 1 [mem 0xfda00000-0xfdafffff]
pci_bus 0000:02: resource 2 [mem 0xfd700000-0xfd7fffff 64bit pref]
pci_bus 0000:03: resource 0 [io  0x9000-0x9fff]
pci_bus 0000:03: resource 1 [mem 0xfd600000-0xfd6fffff]
pci_bus 0000:03: resource 2 [mem 0xfd500000-0xfd5fffff 64bit pref]
pci_bus 0000:04: resource 0 [io  0xd000-0xdfff]
pci_bus 0000:04: resource 1 [mem 0xfde00000-0xfdefffff]
pci_bus 0000:04: resource 2 [mem 0xfdd00000-0xfddfffff 64bit pref]
pci_bus 0000:05: resource 0 [io  0xc000-0xcfff]
pci_bus 0000:05: resource 1 [mem 0xfdc00000-0xfdcfffff]
pci_bus 0000:05: resource 2 [mem 0xfdb00000-0xfdbfffff 64bit pref]
pci_bus 0000:06: resource 0 [io  0x8000-0x8fff]
pci_bus 0000:06: resource 1 [mem 0xfd900000-0xfd9fffff]
pci_bus 0000:06: resource 2 [mem 0xfd800000-0xfd8fffff 64bit pref]
pci_bus 0000:06: resource 4 [io  0x0000-0xffff]
pci_bus 0000:06: resource 5 [mem 0x00000000-0xffffffffffffffff]
pci 0000:01:00.0: Boot video device
PCI: CLS 64 bytes, default 64
pcieport 0000:00:01.0: setting latency timer to 64
pcieport 0000:00:01.0: irq 24 for MSI/MSI-X
pcieport 0000:00:1c.0: setting latency timer to 64
pcieport 0000:00:1c.0: irq 25 for MSI/MSI-X
pcieport 0000:00:1c.2: setting latency timer to 64
pcieport 0000:00:1c.2: irq 26 for MSI/MSI-X
pcieport 0000:00:1c.4: setting latency timer to 64
pcieport 0000:00:1c.4: irq 27 for MSI/MSI-X
pcieport 0000:00:1c.5: setting latency timer to 64
pcieport 0000:00:1c.5: irq 28 for MSI/MSI-X
pcieport 0000:00:01.0: Requesting control of PCIe PME from ACPI BIOS
pcieport 0000:00:01.0: Failed to receive control of PCIe PME service: no _OSC support
pcie_pme: probe of 0000:00:01.0:pcie01 failed with error -13
pcieport 0000:00:1c.0: Requesting control of PCIe PME from ACPI BIOS
pcieport 0000:00:1c.0: Failed to receive control of PCIe PME service: no _OSC support
pcie_pme: probe of 0000:00:1c.0:pcie01 failed with error -13
pcieport 0000:00:1c.2: Requesting control of PCIe PME from ACPI BIOS
pcieport 0000:00:1c.2: Failed to receive control of PCIe PME service: no _OSC support
pcie_pme: probe of 0000:00:1c.2:pcie01 failed with error -13
pcieport 0000:00:1c.4: Requesting control of PCIe PME from ACPI BIOS
pcieport 0000:00:1c.4: Failed to receive control of PCIe PME service: no _OSC support
pcie_pme: probe of 0000:00:1c.4:pcie01 failed with error -13
pcieport 0000:00:1c.5: Requesting control of PCIe PME from ACPI BIOS
pcieport 0000:00:1c.5: Failed to receive control of PCIe PME service: no _OSC support
pcie_pme: probe of 0000:00:1c.5:pcie01 failed with error -13
ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ahci 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input4
pata_jmicron 0000:05:00.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
r8169 0000:03:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
r8169 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
firewire_ohci 0000:06:02.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
input: zc3xx as /devices/pci0000:00/0000:00:1d.2/usb7/7-1/input/input5
input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2:1.0/input/input6
input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2:1.1/input/input7

mkinitcpio.con

HOOKS="base udev autodetect scsi sata dmraid filesystems"

Last edited by fincan (2010-07-31 11:56:54)

fincan

Member

Registered: 2010-07-13

Posts: 27

Re: Samsung Sata Dvdwr and Kernel Panic

Bump!

nixpunk

Member

Registered: 2009-11-23

Posts: 271

Re: Samsung Sata Dvdwr and Kernel Panic

Bumping

Posting a single word or useless message (bumping) to attract attention to your thread is not allowed. Do your own research, continue to troubleshoot, post the results, and be patient with the community. If people are reading your thread without answering or offering help, you may try supplying more details, or ask to be pointed in the right direction. Often, the reason for posts remaining unanswered is due in large part to the sparse details in the original post itself, or, the obvious availability of solutions in the wiki, on the forum (by using the search function) or on the web, and the community's unwillingness to point out the obvious.

http://wiki.archlinux.org/index.php/For … te#Bumping

Anyhow, at what point during boot does this happen?  Did you check the logs for a kernel panic stack trace message?

Last edited by nixpunk (2010-07-31 18:11:58)

fincan

Member

Registered: 2010-07-13

Posts: 27

Re: Samsung Sata Dvdwr and Kernel Panic

well which log should I check? Kernel, Error,... these logs are some confusing .

nixpunk

Member

Registered: 2009-11-23

Posts: 271

Re: Samsung Sata Dvdwr and Kernel Panic

Well, you can check /var/log/messages.log and see if anything related has been logged there.  That's assuming the kernel panic happens after syslog-ng starts up.

Further, have you compared your modules/hooks with your Ubuntu install to see if there are any relevant differences that might be worth exploring?