[SOLVED] lxde wont save

skfrik · 2010-08-07 19:51:42

So, in a console i do have correct keymap,but when i start lxde it changes back to US layout. Also whenever i logout/reboot/shutdown when i start lxde again it doesnt save old settings, doesnt save resolution or any settings

Last edited by skfrik (2010-08-10 14:28:51)

karol · 2010-08-07 20:12:13

Console and X are two different things wrt to keymap. I have 'setxkbmap pl' in my .xinitrc.

What resolution do you have on reboot and which one do you want?

skfrik · 2010-08-07 20:20:34

x.xinitrc solved keymap, thank. It always starts on 1680x1050 and I need it to be 1152x864

karol · 2010-08-07 20:23:54

skfrik wrote:

x.xinitrc solved keymap, thank. It always starts on 1680x1050 and I need it to be 1152x864

Try setting your resolution in xorg.conf or 10-monitor.conf: http://wiki.archlinux.org/index.php/Xor … ng_started

skfrik · 2010-08-07 20:37:40

argh, didn't work, still getting 1680x1050, any other ideas? btw how to save xset m 3 2 (mouse speed), i tried to put it in xinit but didn't workout

karol · 2010-08-07 20:51:45

I think you should keep your xset settings in .xinitrc, so it's weird it didn't work. Be sure to first set the desired settings and only later launch lxde.
If it still doesn't work, post your .xinitrc.

Try

xrandr -s 1152x864

If it works, put it in your .xinitrc.

skfrik · 2010-08-07 20:59:08

great, resolution solved too! but mouse is still slow on start

.xinitrc
setxkbmap hr
xset m 3 2
xrandr -s 1152x864
exec ck-launch-session startlxde

karol · 2010-08-07 21:09:03

Does 'xset m 3 2' work if you type it in the terminal? Try some higher values for threshold, like 'xset m 3 10' or lower acceleration 'xset m 2 2'.

skfrik · 2010-08-07 21:23:48

yea,all combos work fine in terminal, i did try 2,2 but doesnt' work either

karol · 2010-08-07 21:29:13

skfrik wrote:

yea,all combos work fine in terminal, i did try 2,2 but doesnt' work either

Try executing it first:

xset m 3 2
setxkbmap hr
xrandr -s 1152x864
exec ck-launch-session startlxde

Maybe you need to background it 'xset m 3 2 &' but it should work w/o the '&'. Try 'xset mouse 3 2' too.

skfrik · 2010-08-07 21:37:07

tried all 3 solutions, didn't work

skfrik · 2010-08-08 13:51:12

Solved by adding command in /etc/xdg/lxsession/LXDE/autostart

Arch Linux

#1 2010-08-07 19:51:42

[SOLVED] lxde wont save

#2 2010-08-07 20:12:13

Re: [SOLVED] lxde wont save

#3 2010-08-07 20:20:34

Re: [SOLVED] lxde wont save

#4 2010-08-07 20:23:54

Re: [SOLVED] lxde wont save

#5 2010-08-07 20:37:40

Re: [SOLVED] lxde wont save

#6 2010-08-07 20:51:45

Re: [SOLVED] lxde wont save

#7 2010-08-07 20:59:08

Re: [SOLVED] lxde wont save

#8 2010-08-07 21:09:03

Re: [SOLVED] lxde wont save

#9 2010-08-07 21:23:48

Re: [SOLVED] lxde wont save

#10 2010-08-07 21:29:13

Re: [SOLVED] lxde wont save

#11 2010-08-07 21:37:07

Re: [SOLVED] lxde wont save

#12 2010-08-08 13:51:12

Re: [SOLVED] lxde wont save

Board footer