You are not logged in.
Pages: 1
I use a USB 3G Modem (Teracm LW272) to connect to the internet. Whenever the ac supply gets cut off and the laptop switches to battery mode or vice versa, the modem quits unexpectedly.
The part of the dmesg output is attached, when this happens.
usb 2-1: new high speed USB device using ehci_hcd and address 8
option 2-1:1.0: GSM modem (1-port) converter detected
usb 2-1: GSM modem (1-port) converter now attached to ttyUSB0
option 2-1:1.1: GSM modem (1-port) converter detected
usb 2-1: GSM modem (1-port) converter now attached to ttyUSB1
option 2-1:1.2: GSM modem (1-port) converter detected
usb 2-1: GSM modem (1-port) converter now attached to ttyUSB2
option 2-1:1.3: GSM modem (1-port) converter detected
usb 2-1: GSM modem (1-port) converter now attached to ttyUSB3
scsi9 : usb-storage 2-1:1.4
scsi 9:0:0:0: Direct-Access HSPA MMC Storage 2.31 PQ: 0 ANSI: 2
sd 9:0:0:0: Attached scsi generic sg2 type 0
sd 9:0:0:0: [sdb] Attached SCSI removable disk
ata1: hard resetting link
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: configured for UDMA/133
ata1: EH complete
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: configured for UDMA/133
ata1: EH complete
usb 2-1: USB disconnect, address 8
option: option_instat_callback: error -108
option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
option 2-1:1.0: device disconnected
option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
option 2-1:1.1: device disconnected
option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
option 2-1:1.2: device disconnected
option1 ttyUSB3: GSM modem (1-port) converter now disconnected from ttyUSB3
option 2-1:1.3: device disconnected
ADDRCONF(NETDEV_UP): wlan0: link is not ready
usb 2-1: new high speed USB device using ehci_hcd and address 9
option 2-1:1.0: GSM modem (1-port) converter detected
usb 2-1: GSM modem (1-port) converter now attached to ttyUSB0
option 2-1:1.1: GSM modem (1-port) converter detected
usb 2-1: GSM modem (1-port) converter now attached to ttyUSB1
option 2-1:1.2: GSM modem (1-port) converter detected
usb 2-1: GSM modem (1-port) converter now attached to ttyUSB2
option 2-1:1.3: GSM modem (1-port) converter detected
usb 2-1: GSM modem (1-port) converter now attached to ttyUSB3
scsi10 : usb-storage 2-1:1.4
scsi 10:0:0:0: Direct-Access HSPA MMC Storage 2.31 PQ: 0 ANSI: 2
sd 10:0:0:0: Attached scsi generic sg2 type 0
sd 10:0:0:0: [sdb] Attached SCSI removable disk
atkbd serio0: Unknown key pressed (translated set 2, code 0x8e on isa0060/serio0).
atkbd serio0: Use 'setkeycodes e00e <keycode>' to make it known.
atkbd serio0: Unknown key pressed (translated set 2, code 0x8e on isa0060/serio0).
atkbd serio0: Use 'setkeycodes e00e <keycode>' to make it known.
ADDRCONF(NETDEV_UP): wlan0: link is not ready
ADDRCONF(NETDEV_UP): wlan0: link is not ready
Last edited by theta (2010-09-03 04:03:01)
Offline
The same doen't happen if I use the modem on Windows XP or the power goes for a very short time, like less than 1.5 secs.
Regards,
Apoorv
Offline
Pages: 1