You are not logged in.
Hey I was trying to get Starcraft II to work on my laptop, but unfortunately the lag is unbearable, I cannot even get logged in. So I have to decided to switch the open-source driver to the proprietary driver for my ati hd 5870 graphics card.
I have tried yaourt -S catalyst but I come to a point where it says:
catalyst-utils and libgl are in conflict. Remove libgl?
So I tried pacman -Rd libgl and i get
checking dependencies...
error: failed to prepare transaction (could not satisfy dependencies)
:: ati-dri: requires libgl
:: lib32-libgl: requires libgl
:: libva: requires libgl
:: mesa: requires libgl
:: mplayer2: requires libgl
:: qt: requires libgl
:: xorg-xdriinfo: requires libgl
I read somewhere I must use pacman -Rdd instead to get it off my computer.
But I'm worried that if i do I will mess up my computer, and I won't be able to use mplayer anymore.
Can anybody please give me some advice for switching my drivers.
Or if there is a way I can choose which driver I want to use on boot?
Help it greatly appreciated!
Last edited by Jabrick (2011-07-01 15:56:46)
Offline
If you want to install catalyst you need to remove libgl so...
Remove it and install catalyst. I did it, didn't had any problems.
Offline
Everything worked as normal?
As well as mplayer? (If you use it to begin with)
I just don't want to fall into some trouble because I don't have so much time on my hands lately, and still a newbie in linux
Is it also easy to switch back to open-source driver if need be?
Offline
Hi,
I have a Ati 5770 working great!!
Just follow this guide:
https://wiki.archlinux.org/index.php/ATI_Catalyst
But i didn't use the AUR driver, i just installed the catalyst repo and that's all
Good luck!
the truth is out there....
Offline
Everything worked as normal?
As well as mplayer? (If you use it to begin with)
I just don't want to fall into some trouble because I don't have so much time on my hands lately, and still a newbie in linux
Is it also easy to switch back to open-source driver if need be?
Yes I used mplayer. I think I' lucky because I didn't had, yet, any serious problems with catalyst. And for any reason you want to go back to opensource is the same procedure. It's very easy without any problem
You can use the reppository of catalyst like it was mention above
Offline
Everything will still work because catalyst-utils provides the libgl dependency. If something conflicted with libgl without providing its own GL library that would be strange.
6EA3 F3F3 B908 2632 A9CB E931 D53A 0445 B47A 0DAB
Great things come in tar.xz packages.
Offline
Before you install catalyst, remove _all_ the xf86-video-* and *-dri packages, Then just -Syu catalyst-whatever catalyst-utils from the catalyst repo, and pacman should handle the libgl replace fine without user intervention.
Evil #archlinux@libera.chat channel op and general support dude.
. files on github, Screenshots, Random pics and the rest
Offline
Thank you for the support everybody, I went ahead and installed the catalyst driver from the repository mentioned in the guide.
I rebooted and SLiM didn't start so I used
aticonfig --initial
It created an xorg.conf
I then rebooted and not after it boots I get a white flash and the screen turns off.
HELP!
I can't even access my virtual console!!!
Is it possible to go back? Recover my computer from a previous time??
--Panicked arch user
Offline
Did you disable kms as the wiki said?
Evil #archlinux@libera.chat channel op and general support dude.
. files on github, Screenshots, Random pics and the rest
Offline
Did you disable kms as the wiki said?
....
No I didn't!!!
Is there anyway I can reach my xorg.conf to disable it???
Thank you so much for the quick response!
UPDATE: So in grub i added "3 nomodeset" to the end of my kernel line and I am able to boot into my computer again.
I added the lines Mr.Elendig suggested and my /etc/X11/xorg.conf looks like this
Section "ServerLayout"
Identifier "aticonfig Layout"
Screen 0 "aticonfig-Screen[0]-0" 0 0
EndSection
Section "Module"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]-0"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]-0"
Driver "fglrx"
BusID "PCI:1:0:0"
Option "UseInternalAGPGART" "no"
Option "KernelModuleParm" "agplock=0" #AGP locked user pages: disabled
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]-0"
Device "aticonfig-Device[0]-0"
Monitor "aticonfig-Monitor[0]-0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Unfortunatley I still cannot boot normally after the adjustment.
Does anyone know what steps I should take to fix my computer?
Thanks again for the support.
UPDATE 2: Forget it ati proprietary drivers slows down my xmonad anyways. Too much headache and starcraft still didnt work.
I got the opensource drive back and learned alot Thanks everyone.
I will now attempt to dual boot win7. (Which i have tied previously it was a nightmare, was never stable)
Wish me luck!
Last edited by Jabrick (2011-07-01 16:46:06)
Offline
Good luck!
About adding the "nomodeset" line. You mean that you can boot into your system with proprietary drivers but only when you add that manually at the bootloader screen? You can also put it in your /boot/grub/menu.lst so it's automatically added every time.
6EA3 F3F3 B908 2632 A9CB E931 D53A 0445 B47A 0DAB
Great things come in tar.xz packages.
Offline