You are not logged in.
- Topics: Active | Unanswered
#1 2011-10-22 21:56:05
- Revestek
- Member
- Registered: 2011-10-22
- Posts: 5
[SOLVED] wpa_supplicant causes system to crash
UPDATE: For anyone else having this problem, Gusar provided the solution that worked for me here
FIrst, let me say that I'm relatively new to Arch, so please bear with me.
Whenever I try to connect to my wireless network according to the wiki article on 'wireless setup', the terminal freezes (I can't ^C), and I end up having to hard reboot. The computer does still respond, but I can't do anything related to networking.
My wireless adapter is a Broadcom BCM43225.
Output from 'wpa_supplicant -ddd -Dwext -i wlan0 -c /etc/wpa_supplicant.conf':
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ctrl_interface='DIR=/var/run/wpa_supplicant GROUP=wheel'
Line: 2 - start of a new network block
ssid - hexdump_ascii(len=9):
64 6c 69 6e 6b 32 39 32 35 dlink2925
PSK - hexdump(len=32): [REMOVED]
Priority group 0
id=0 ssid='dlink2925'
WEXT: cfg80211-based driver detected
SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf flags 0x0
netlink: Operstate: linkmode=1, operstate=5
Own MAC address: b4:74:9f:f7:25:17
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
RSN: flushing PMKID list in the driver
Setting scan request: 0 sec 100000 usec
WPS: UUID based on MAC address - hexdump(len=16): 5f c3 d8 5a 7c 14 5b 3f b3 c1 ab f8 d5 87 2a cf
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: Supplicant port status: Unauthorized
EAPOL: Supplicant port status: Unauthorized
Using existing control interface directory.
ctrl_interface_group=10 (from group name 'wheel')
Added interface wlan0
RTM_NEWLINK: operstate=0 ifi_flags=0x1043 ([UP][RUNNING])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b06 len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b1a len=16
State: DISCONNECTED -> SCANNING
Starting AP scan for wildcard SSID
Scan requested (ret=0) - scan timeout 5 seconds
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b19 len=16
Received 1735 bytes of scan results (3 BSSes)
BSS: Start scan result update 1
BSS: Add new id 0 BSSID 00:18:e7:d1:6c:28 SSID 'dlink2925'
BSS: Add new id 1 BSSID 00:19:5b:b2:89:bd SSID 'Drage'
BSS: Add new id 2 BSSID 14:d6:4d:38:36:a4 SSID 'lassenett'
New scan results available
WPS: attr type=0x104a len=1
WPS: attr type=0x1044 len=1
WPS: attr type=0x103b len=1
WPS: attr type=0x1047 len=16
WPS: attr type=0x1021 len=14
WPS: attr type=0x1023 len=7
WPS: attr type=0x1024 len=2
WPS: attr type=0x1042 len=4
WPS: attr type=0x1054 len=8
WPS: attr type=0x1011 len=23
WPS: attr type=0x1008 len=2
WPS: attr type=0x104a len=1
WPS: attr type=0x1044 len=1
WPS: attr type=0x103b len=1
WPS: attr type=0x1047 len=16
WPS: attr type=0x1021 len=14
WPS: attr type=0x1023 len=7
WPS: attr type=0x1024 len=2
WPS: attr type=0x1042 len=4
WPS: attr type=0x1054 len=8
WPS: attr type=0x1011 len=23
WPS: attr type=0x1008 len=2
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:18:e7:d1:6c:28 ssid='dlink2925' wpa_ie_len=26 rsn_ie_len=24 caps=0x11
selected based on RSN IE
selected WPA AP 00:18:e7:d1:6c:28 ssid='dlink2925'
Trying to associate with 00:18:e7:d1:6c:28 (SSID='dlink2925' freq=2472 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
RSN: using IEEE 802.11i/D9.0
WPA: Selected cipher suites: group 8 pairwise 24 key_mgmt 2 proto 2
WPA: set AP WPA IE - hexdump(len=28): dd 1a 00 50 f2 01 01 00 00 50 f2 02 02 00 00 50 f2 02 00 50 f2 04 01 00 00 50 f2 02
WPA: set AP RSN IE - hexdump(len=26): 30 18 01 00 00 0f ac 02 02 00 00 0f ac 02 00 0f ac 04 01 00 00 0f ac 02 00 00
WPA: using GTK TKIP
WPA: using PTK CCMP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
No keys have been configured - skip key clearing
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_pskI have consulted the forums and wiki, so I hope someone is able to help.
If you need any more info like logfiles etc. let me know.
Last edited by Revestek (2011-10-23 18:08:03)
Offline
#2 2011-10-22 22:03:41
- Gusar
- Member
- Registered: 2009-08-25
- Posts: 3,605
Re: [SOLVED] wpa_supplicant causes system to crash
The output of dmesg would be useful. But just at a guess, blacklist the bcma and b43 modules. Another thing to try, use -Dnl80211 instead of -Dwext
Last edited by Gusar (2011-10-22 22:05:11)
Offline
#3 2011-10-22 22:52:59
- Revestek
- Member
- Registered: 2011-10-22
- Posts: 5
Re: [SOLVED] wpa_supplicant causes system to crash
Thank you for your response!
I blacklisted bcma and b43 and tried nl80211, and there was some change. Now I can still use the wired connection after having tried to start wireless, but as soon as I hit ctrl+c it breaks.
Here's the outpout from wpa_supplicant when using nl80211:
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'nl80211' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ctrl_interface='DIR=/var/run/wpa_supplicant GROUP=wheel'
Line: 2 - start of a new network block
ssid - hexdump_ascii(len=9):
64 6c 69 6e 6b 32 39 32 35 dlink2925
PSK - hexdump(len=32): [REMOVED]
Priority group 0
id=0 ssid='dlink2925'
netlink: Operstate: linkmode=1, operstate=5
Own MAC address: b4:74:9f:f7:25:17
wpa_driver_nl80211_set_key: ifindex=3 alg=0 addr=0x464cd9 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=3 alg=0 addr=0x464cd9 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=3 alg=0 addr=0x464cd9 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=3 alg=0 addr=0x464cd9 key_idx=3 set_tx=0 seq_len=0 key_len=0
RSN: flushing PMKID list in the driver
Setting scan request: 0 sec 100000 usec
WPS: UUID based on MAC address - hexdump(len=16): 5f c3 d8 5a 7c 14 5b 3f b3 c1 ab f8 d5 87 2a cf
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: Supplicant port status: Unauthorized
EAPOL: Supplicant port status: Unauthorized
ctrl_interface_group=10 (from group name 'wheel')
Added interface wlan0
RTM_NEWLINK: operstate=0 ifi_flags=0x1043 ([UP][RUNNING])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
State: DISCONNECTED -> SCANNING
Starting AP scan for wildcard SSID
nl80211: Scan SSID - hexdump_ascii(len=0): [NULL]
Scan requested (ret=0) - scan timeout 10 seconds
nl80211: Event message available
nl80211: Scan trigger
nl80211: Event message available
nl80211: New scan results available
Received scan results (3 BSSes)
BSS: Start scan result update 1
BSS: Add new id 0 BSSID 00:18:e7:d1:6c:28 SSID 'dlink2925'
BSS: Add new id 1 BSSID 00:19:5b:b2:89:bd SSID 'Drage'
BSS: Add new id 2 BSSID 6c:f0:49:a0:6b:e4 SSID 'Redet'
New scan results available
WPS: attr type=0x104a len=1
WPS: attr type=0x1044 len=1
WPS: attr type=0x104a len=1
WPS: attr type=0x1044 len=1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:18:e7:d1:6c:28 ssid='dlink2925' wpa_ie_len=26 rsn_ie_len=24 caps=0x431
selected based on RSN IE
selected WPA AP 00:18:e7:d1:6c:28 ssid='dlink2925'
Automatic auth_alg selection: 0x1
RSN: using IEEE 802.11i/D9.0
WPA: Selected cipher suites: group 8 pairwise 24 key_mgmt 2 proto 2
WPA: set AP WPA IE - hexdump(len=28): dd 1a 00 50 f2 01 01 00 00 50 f2 02 02 00 00 50 f2 02 00 50 f2 04 01 00 00 50 f2 02
WPA: set AP RSN IE - hexdump(len=26): 30 18 01 00 00 0f ac 02 02 00 00 0f ac 02 00 0f ac 04 01 00 00 0f ac 02 00 00
WPA: using GTK TKIP
WPA: using PTK CCMP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
Cancelling scan request
Trying to authenticate with 00:18:e7:d1:6c:28 (SSID='dlink2925' freq=2472 MHz)
No keys have been configured - skip key clearing
State: SCANNING -> AUTHENTICATING
EAPOL: External notification - EAP success=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - EAP fail=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portControl=Auto
EAPOL: Supplicant port status: Unauthorized
nl80211: Authenticate (ifindex=3)
* bssid=00:18:e7:d1:6c:28
* freq=2472
* SSID - hexdump_ascii(len=9):
64 6c 69 6e 6b 32 39 32 35 dlink2925
* IEs - hexdump(len=0): [NULL]
* Auth Type 0
nl80211: Authentication request send successfully
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
EAPOL: disable timer tick
EAPOL: Supplicant port status: UnauthorizedAnd here's dmesg:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.0-ARCH (tobias@T-POWA-LX) (gcc version 4.6.1 20110819 (prerelease) (GCC) ) #1 SMP PREEMPT Wed Oct 19 10:27:51 CEST 2011
[ 0.000000] Command line: root=/dev/sda3 rootfstype=ext4 resume=/dev/sda2 ro
[ 0.000000] Disabled fast string operations
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009d800 (usable)
[ 0.000000] BIOS-e820: 000000000009d800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007a3ef000 (usable)
[ 0.000000] BIOS-e820: 000000007a3ef000 - 000000007a6ef000 (reserved)
[ 0.000000] BIOS-e820: 000000007a6ef000 - 000000007a79f000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007a79f000 - 000000007a7ff000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007a7ff000 - 000000007a800000 (usable)
[ 0.000000] BIOS-e820: 000000007a800000 - 000000007f200000 (reserved)
[ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed08000 - 00000000fed09000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed10000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffd80000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000100600000 (usable)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.6 present.
[ 0.000000] DMI: SAMSUNG ELECTRONICS CO., LTD. 900X1B/900X1B, BIOS 01FQ 06/09/2011
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x100600 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0FFC00000 mask FFFC00000 write-protect
[ 0.000000] 1 base 000000000 mask F80000000 write-back
[ 0.000000] 2 base 07C000000 mask FFC000000 uncachable
[ 0.000000] 3 base 07B000000 mask FFF000000 uncachable
[ 0.000000] 4 base 07A800000 mask FFF800000 uncachable
[ 0.000000] 5 base 100000000 mask FE0000000 write-back
[ 0.000000] 6 base 110000000 mask FF0000000 uncachable
[ 0.000000] 7 base 108000000 mask FF8000000 uncachable
[ 0.000000] 8 base 104000000 mask FFC000000 uncachable
[ 0.000000] 9 base 102000000 mask FFE000000 uncachable
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] last_pfn = 0x7a800 max_arch_pfn = 0x400000000
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 20480
[ 0.000000] init_memory_mapping: 0000000000000000-000000007a800000
[ 0.000000] 0000000000 - 007a800000 page 2M
[ 0.000000] kernel direct mapping tables up to 7a800000 @ 7a3ec000-7a3ef000
[ 0.000000] init_memory_mapping: 0000000100000000-0000000100600000
[ 0.000000] 0100000000 - 0100600000 page 2M
[ 0.000000] kernel direct mapping tables up to 100600000 @ 1005fa000-100600000
[ 0.000000] RAMDISK: 37dcc000 - 37ff0000
[ 0.000000] ACPI: RSDP 00000000000f00e0 00024 (v02 SECCSD)
[ 0.000000] ACPI: XSDT 000000007a7fe120 00084 (v01 SECCSD LH43STAR 00000002 PTEC 00000002)
[ 0.000000] ACPI: FACP 000000007a7ef000 000F4 (v03 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: DSDT 000000007a7f2000 0828A (v02 SECCSD SNB-CPT 00000000 INTL 20061109)
[ 0.000000] ACPI: FACS 000000007a73e000 00040
[ 0.000000] ACPI: SLIC 000000007a7fd000 00176 (v01 SECCSD LH43STAR 00000002 PTEC 00000001)
[ 0.000000] ACPI: SSDT 000000007a7fb000 01068 (v01 SECCSD PtidDevc 00001000 INTL 20061109)
[ 0.000000] ACPI: ASF! 000000007a7f1000 000A5 (v32 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: HPET 000000007a7ee000 00038 (v01 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: APIC 000000007a7ed000 00098 (v01 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: MCFG 000000007a7ec000 0003C (v01 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: SSDT 000000007a7eb000 006FC (v01 PmRef Cpu0Ist 00003000 INTL 20061109)
[ 0.000000] ACPI: SSDT 000000007a7ea000 00996 (v01 PmRef CpuPm 00003000 INTL 20061109)
[ 0.000000] ACPI: UEFI 000000007a7e9000 0003E (v01 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: UEFI 000000007a7e8000 00042 (v01 PTL COMBUF 00000001 PTL 00000001)
[ 0.000000] ACPI: UEFI 000000007a7e7000 00256 (v01 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-0000000100600000
[ 0.000000] Initmem setup node 0 0000000000000000-0000000100600000
[ 0.000000] NODE_DATA [00000001005fb000 - 00000001005fffff]
[ 0.000000] [ffffea0000000000-ffffea00039fffff] PMD -> [ffff880077c00000-ffff8800799fffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00100600
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[4] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009d
[ 0.000000] 0: 0x00000100 -> 0x0007a3ef
[ 0.000000] 0: 0x0007a7ff -> 0x0007a800
[ 0.000000] 0: 0x00100000 -> 0x00100600
[ 0.000000] On node 0 totalpages: 502141
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 5 pages reserved
[ 0.000000] DMA zone: 3920 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 482344 pages, LIFO batch:31
[ 0.000000] Normal zone: 21 pages used for memmap
[ 0.000000] Normal zone: 1515 pages, LIFO batch:0
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000
[ 0.000000] SMP: Allowing 8 CPUs, 4 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009d000 - 000000000009e000
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 000000007a3ef000 - 000000007a6ef000
[ 0.000000] PM: Registered nosave memory: 000000007a6ef000 - 000000007a79f000
[ 0.000000] PM: Registered nosave memory: 000000007a79f000 - 000000007a7ff000
[ 0.000000] PM: Registered nosave memory: 000000007a800000 - 000000007f200000
[ 0.000000] PM: Registered nosave memory: 000000007f200000 - 00000000f8000000
[ 0.000000] PM: Registered nosave memory: 00000000f8000000 - 00000000fc000000
[ 0.000000] PM: Registered nosave memory: 00000000fc000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
[ 0.000000] PM: Registered nosave memory: 00000000fec01000 - 00000000fed08000
[ 0.000000] PM: Registered nosave memory: 00000000fed08000 - 00000000fed09000
[ 0.000000] PM: Registered nosave memory: 00000000fed09000 - 00000000fed10000
[ 0.000000] PM: Registered nosave memory: 00000000fed10000 - 00000000fed1a000
[ 0.000000] PM: Registered nosave memory: 00000000fed1a000 - 00000000fed1c000
[ 0.000000] PM: Registered nosave memory: 00000000fed1c000 - 00000000fed20000
[ 0.000000] PM: Registered nosave memory: 00000000fed20000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ffd80000
[ 0.000000] PM: Registered nosave memory: 00000000ffd80000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at 7f200000 (gap: 7f200000:78e00000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 27 pages/cpu @ffff880100200000 s78464 r8192 d23936 u262144
[ 0.000000] pcpu-alloc: s78464 r8192 d23936 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 487779
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: root=/dev/sda3 rootfstype=ext4 resume=/dev/sda2 ro
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave/xrstor: enabled xstate_bv 0x7, cntxt size 0x340
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 1899028k/4200448k available (4066k kernel code, 2191884k absent, 109536k reserved, 3302k data, 712k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:2304
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 17825792 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.003333] Detected 1297.092 MHz processor.
[ 0.000004] Calibrating delay loop (skipped), value calculated using timer frequency.. 2595.27 BogoMIPS (lpj=4323640)
[ 0.000010] pid_max: default: 32768 minimum: 301
[ 0.000199] Security Framework initialized
[ 0.000205] AppArmor: AppArmor disabled by boot time parameter
[ 0.000593] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.001434] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.001785] Mount-cache hash table entries: 256
[ 0.002309] Initializing cgroup subsys cpuacct
[ 0.002355] Initializing cgroup subsys memory
[ 0.002379] Initializing cgroup subsys devices
[ 0.002382] Initializing cgroup subsys freezer
[ 0.002385] Initializing cgroup subsys net_cls
[ 0.002388] Initializing cgroup subsys blkio
[ 0.002462] Disabled fast string operations
[ 0.002465] CPU: Physical Processor ID: 0
[ 0.002468] CPU: Processor Core ID: 0
[ 0.002476] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.002478] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.002482] mce: CPU supports 7 MCE banks
[ 0.002501] CPU0: Thermal monitoring enabled (TM1)
[ 0.002513] using mwait in idle threads.
[ 0.003883] ACPI: Core revision 20110413
[ 0.018341] ftrace: allocating 16144 entries in 64 pages
[ 0.027758] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.060747] CPU0: Intel(R) Core(TM) i3-2357M CPU @ 1.30GHz stepping 07
[ 0.167197] Performance Events: PEBS fmt1+, SandyBridge events, Intel PMU driver.
[ 0.167206] ... version: 3
[ 0.167208] ... bit width: 48
[ 0.167210] ... generic registers: 4
[ 0.167212] ... value mask: 0000ffffffffffff
[ 0.167214] ... max period: 000000007fffffff
[ 0.167217] ... fixed-purpose events: 3
[ 0.167219] ... event mask: 000000070000000f
[ 0.187381] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.213857] Booting Node 0, Processors #1
[ 0.213863] smpboot cpu 1: start_ip = 98000
[ 0.307121] Disabled fast string operations
[ 0.327209] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.347126] #2
[ 0.347138] smpboot cpu 2: start_ip = 98000
[ 0.440365] Disabled fast string operations
[ 0.460448] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.480363] #3
[ 0.480366] smpboot cpu 3: start_ip = 98000
[ 0.573609] Disabled fast string operations
[ 0.593676] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.600252] Brought up 4 CPUs
[ 0.600257] Total of 4 processors activated (10380.53 BogoMIPS).
[ 0.604579] devtmpfs: initialized
[ 0.605768] PM: Registering ACPI NVS region at 7a6ef000 (720896 bytes)
[ 0.607046] print_constraints: dummy:
[ 0.607158] NET: Registered protocol family 16
[ 0.607301] ACPI: bus type pci registered
[ 0.607538] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.607542] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.625509] PCI: Using configuration type 1 for base access
[ 0.626174] bio: create slab <bio-0> at 0
[ 0.628558] ACPI: EC: Look up EC in DSDT
[ 0.630714] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.650312] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.661407] ACPI: SSDT 000000007a6e0718 00670 (v01 PmRef Cpu0Cst 00003001 INTL 20061109)
[ 0.661954] ACPI: Dynamic OEM Table Load:
[ 0.661958] ACPI: SSDT (null) 00670 (v01 PmRef Cpu0Cst 00003001 INTL 20061109)
[ 0.670573] ACPI: SSDT 000000007a6e1a98 00303 (v01 PmRef ApIst 00003000 INTL 20061109)
[ 0.671157] ACPI: Dynamic OEM Table Load:
[ 0.671161] ACPI: SSDT (null) 00303 (v01 PmRef ApIst 00003000 INTL 20061109)
[ 0.680357] ACPI: SSDT 000000007a6dfd98 00119 (v01 PmRef ApCst 00003000 INTL 20061109)
[ 0.680902] ACPI: Dynamic OEM Table Load:
[ 0.680906] ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000 INTL 20061109)
[ 0.693632] ACPI: Interpreter enabled
[ 0.693638] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.693674] ACPI: Using IOAPIC for interrupt routing
[ 0.713260] ACPI: Power Resource [FN00] (off)
[ 0.713380] ACPI: Power Resource [FN01] (off)
[ 0.713495] ACPI: Power Resource [FN02] (off)
[ 0.713627] ACPI: Power Resource [FN03] (off)
[ 0.713745] ACPI: Power Resource [FN04] (off)
[ 0.714187] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[ 0.714438] ACPI: No dock devices found.
[ 0.714441] HEST: Table not found.
[ 0.714445] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.715130] \_SB_.PCI0:_OSC invalid UUID
[ 0.715132] _OSC request data:1 8 1f
[ 0.715138] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 0.715976] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 0.715980] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 0.715984] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.715989] pci_root PNP0A08:00: host bridge window [mem 0x7f200000-0xfeafffff]
[ 0.715993] pci_root PNP0A08:00: host bridge window [mem 0xfed40000-0xfed44fff]
[ 0.716009] pci 0000:00:00.0: [8086:0104] type 0 class 0x000600
[ 0.716062] pci 0000:00:02.0: [8086:0116] type 0 class 0x000300
[ 0.716080] pci 0000:00:02.0: reg 10: [mem 0x90000000-0x903fffff 64bit]
[ 0.716091] pci 0000:00:02.0: reg 18: [mem 0x80000000-0x8fffffff 64bit pref]
[ 0.716099] pci 0000:00:02.0: reg 20: [io 0x3000-0x303f]
[ 0.716189] pci 0000:00:16.0: [8086:1c3a] type 0 class 0x000780
[ 0.716229] pci 0000:00:16.0: reg 10: [mem 0x90705000-0x9070500f 64bit]
[ 0.716336] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.716343] pci 0000:00:16.0: PME# disabled
[ 0.716401] pci 0000:00:1a.0: [8086:1c2d] type 0 class 0x000c03
[ 0.716437] pci 0000:00:1a.0: reg 10: [mem 0x9070a000-0x9070a3ff]
[ 0.716563] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.716570] pci 0000:00:1a.0: PME# disabled
[ 0.716611] pci 0000:00:1b.0: [8086:1c20] type 0 class 0x000403
[ 0.716641] pci 0000:00:1b.0: reg 10: [mem 0x90700000-0x90703fff 64bit]
[ 0.716750] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.716757] pci 0000:00:1b.0: PME# disabled
[ 0.716791] pci 0000:00:1c.0: [8086:1c10] type 1 class 0x000604
[ 0.716914] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.716921] pci 0000:00:1c.0: PME# disabled
[ 0.716965] pci 0000:00:1c.3: [8086:1c16] type 1 class 0x000604
[ 0.717080] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.717087] pci 0000:00:1c.3: PME# disabled
[ 0.717125] pci 0000:00:1c.4: [8086:1c18] type 1 class 0x000604
[ 0.717240] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.717246] pci 0000:00:1c.4: PME# disabled
[ 0.717301] pci 0000:00:1d.0: [8086:1c26] type 0 class 0x000c03
[ 0.717337] pci 0000:00:1d.0: reg 10: [mem 0x90709000-0x907093ff]
[ 0.717463] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.717470] pci 0000:00:1d.0: PME# disabled
[ 0.717507] pci 0000:00:1f.0: [8086:1c49] type 0 class 0x000601
[ 0.717693] pci 0000:00:1f.2: [8086:1c03] type 0 class 0x000106
[ 0.717733] pci 0000:00:1f.2: reg 10: [io 0x3088-0x308f]
[ 0.717750] pci 0000:00:1f.2: reg 14: [io 0x3094-0x3097]
[ 0.717766] pci 0000:00:1f.2: reg 18: [io 0x3080-0x3087]
[ 0.717782] pci 0000:00:1f.2: reg 1c: [io 0x3090-0x3093]
[ 0.717799] pci 0000:00:1f.2: reg 20: [io 0x3060-0x307f]
[ 0.717815] pci 0000:00:1f.2: reg 24: [mem 0x90708000-0x907087ff]
[ 0.717886] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.717892] pci 0000:00:1f.2: PME# disabled
[ 0.717924] pci 0000:00:1f.3: [8086:1c22] type 0 class 0x000c05
[ 0.717954] pci 0000:00:1f.3: reg 10: [mem 0x90704000-0x907040ff 64bit]
[ 0.717996] pci 0000:00:1f.3: reg 20: [io 0xefa0-0xefbf]
[ 0.718190] pci 0000:01:00.0: [14e4:4357] type 0 class 0x000280
[ 0.718231] pci 0000:01:00.0: reg 10: [mem 0x90600000-0x90603fff 64bit]
[ 0.718394] pci 0000:01:00.0: supports D1 D2
[ 0.718397] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.718404] pci 0000:01:00.0: PME# disabled
[ 0.723567] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 0.723574] pci 0000:00:1c.0: bridge window [io 0xf000-0x0000] (disabled)
[ 0.723581] pci 0000:00:1c.0: bridge window [mem 0x90600000-0x906fffff]
[ 0.723592] pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.723756] pci 0000:02:00.0: [10ec:8168] type 0 class 0x000200
[ 0.723832] pci 0000:02:00.0: reg 10: [io 0x2000-0x20ff]
[ 0.723968] pci 0000:02:00.0: reg 18: [mem 0x90404000-0x90404fff 64bit pref]
[ 0.724052] pci 0000:02:00.0: reg 20: [mem 0x90400000-0x90403fff 64bit pref]
[ 0.724291] pci 0000:02:00.0: supports D1 D2
[ 0.724294] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.724311] pci 0000:02:00.0: PME# disabled
[ 0.730232] pci 0000:00:1c.3: PCI bridge to [bus 02-02]
[ 0.730239] pci 0000:00:1c.3: bridge window [io 0x2000-0x2fff]
[ 0.730246] pci 0000:00:1c.3: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 0.730257] pci 0000:00:1c.3: bridge window [mem 0x90400000-0x904fffff 64bit pref]
[ 0.730370] pci 0000:03:00.0: [1033:0194] type 0 class 0x000c03
[ 0.730409] pci 0000:03:00.0: reg 10: [mem 0x90500000-0x90501fff 64bit]
[ 0.730564] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[ 0.730572] pci 0000:03:00.0: PME# disabled
[ 0.730647] pci 0000:00:1c.4: PCI bridge to [bus 03-03]
[ 0.730653] pci 0000:00:1c.4: bridge window [io 0xf000-0x0000] (disabled)
[ 0.730661] pci 0000:00:1c.4: bridge window [mem 0x90500000-0x905fffff]
[ 0.730671] pci 0000:00:1c.4: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.730702] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.730867] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.730921] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
[ 0.730967] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP05._PRT]
[ 0.731173] \_SB_.PCI0:_OSC invalid UUID
[ 0.731175] _OSC request data:1 1f 1f
[ 0.731181] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.731307] \_SB_.PCI0:_OSC invalid UUID
[ 0.731309] _OSC request data:1 0 1d
[ 0.731314] pci0000:00: ACPI _OSC request failed (AE_ERROR), returned control mask: 0x1d
[ 0.731317] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 0.735022] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[ 0.735090] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.735158] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[ 0.735221] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[ 0.735285] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 *5 6 10 11 12 14 15)
[ 0.735348] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.735412] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[ 0.735475] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 *5 6 10 11 12 14 15)
[ 0.735594] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.735603] vgaarb: loaded
[ 0.735605] vgaarb: bridge control possible 0000:00:02.0
[ 0.735707] PCI: Using ACPI for IRQ routing
[ 0.739317] PCI: pci_cache_line_size set to 64 bytes
[ 0.739435] reserve RAM buffer: 000000000009d800 - 000000000009ffff
[ 0.739438] reserve RAM buffer: 000000007a3ef000 - 000000007bffffff
[ 0.739442] reserve RAM buffer: 000000007a800000 - 000000007bffffff
[ 0.739445] reserve RAM buffer: 0000000100600000 - 0000000103ffffff
[ 0.739602] NetLabel: Initializing
[ 0.739605] NetLabel: domain hash size = 128
[ 0.739607] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.739627] NetLabel: unlabeled traffic allowed by default
[ 0.739648] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.739656] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.741679] Switching to clocksource hpet
[ 0.743496] Switched to NOHz mode on CPU #0
[ 0.743583] Switched to NOHz mode on CPU #3
[ 0.743599] Switched to NOHz mode on CPU #2
[ 0.743606] Switched to NOHz mode on CPU #1
[ 0.748890] pnp: PnP ACPI init
[ 0.748911] ACPI: bus type pnp registered
[ 0.749374] pnp 00:00: [bus 00-3e]
[ 0.749378] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.749381] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.749384] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.749387] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.749390] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 0.749393] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 0.749396] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 0.749399] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 0.749402] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 0.749405] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 0.749411] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 0.749414] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 0.749417] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[ 0.749420] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[ 0.749423] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[ 0.749426] pnp 00:00: [mem 0x000ec000-0x000effff window]
[ 0.749429] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[ 0.749432] pnp 00:00: [mem 0x7f200000-0xfeafffff window]
[ 0.749435] pnp 00:00: [mem 0xfed40000-0xfed44fff window]
[ 0.749528] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.749856] pnp 00:01: [io 0x0000-0x001f]
[ 0.749859] pnp 00:01: [io 0x0081-0x0091]
[ 0.749862] pnp 00:01: [io 0x0093-0x009f]
[ 0.749864] pnp 00:01: [io 0x00c0-0x00df]
[ 0.749867] pnp 00:01: [dma 4]
[ 0.749901] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.749913] pnp 00:02: [mem 0xff000000-0xffffffff]
[ 0.749942] pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.750043] pnp 00:03: [mem 0xfed00000-0xfed003ff]
[ 0.750080] pnp 00:03: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.750094] pnp 00:04: [io 0x00f0]
[ 0.750106] pnp 00:04: [irq 13]
[ 0.750136] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.750152] pnp 00:05: [io 0x002e-0x002f]
[ 0.750155] pnp 00:05: [io 0x004e-0x004f]
[ 0.750157] pnp 00:05: [io 0x0061]
[ 0.750159] pnp 00:05: [io 0x0063]
[ 0.750162] pnp 00:05: [io 0x0065]
[ 0.750164] pnp 00:05: [io 0x0067]
[ 0.750166] pnp 00:05: [io 0x0070]
[ 0.750169] pnp 00:05: [io 0x0080]
[ 0.750171] pnp 00:05: [io 0x0092]
[ 0.750173] pnp 00:05: [io 0x00b2-0x00b3]
[ 0.750176] pnp 00:05: [io 0x0680-0x069f]
[ 0.750178] pnp 00:05: [io 0x1000-0x100f]
[ 0.750181] pnp 00:05: [io 0x5000-0x5003]
[ 0.750183] pnp 00:05: [io 0xffff]
[ 0.750186] pnp 00:05: [io 0x0400-0x0453]
[ 0.750188] pnp 00:05: [io 0x0458-0x047f]
[ 0.750191] pnp 00:05: [io 0x0500-0x057f]
[ 0.750193] pnp 00:05: [io 0x0a00-0x0a0f]
[ 0.750196] pnp 00:05: [io 0x164e-0x164f]
[ 0.750198] pnp 00:05: [io 0x5000-0x500f]
[ 0.750259] system 00:05: [io 0x0680-0x069f] has been reserved
[ 0.750263] system 00:05: [io 0x1000-0x100f] has been reserved
[ 0.750266] system 00:05: [io 0x5000-0x5003] has been reserved
[ 0.750269] system 00:05: [io 0xffff] has been reserved
[ 0.750273] system 00:05: [io 0x0400-0x0453] has been reserved
[ 0.750276] system 00:05: [io 0x0458-0x047f] has been reserved
[ 0.750280] system 00:05: [io 0x0500-0x057f] has been reserved
[ 0.750283] system 00:05: [io 0x0a00-0x0a0f] has been reserved
[ 0.750286] system 00:05: [io 0x164e-0x164f] has been reserved
[ 0.750290] system 00:05: [io 0x5000-0x500f] could not be reserved
[ 0.750295] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.750307] pnp 00:06: [io 0x0070-0x0077]
[ 0.750314] pnp 00:06: [irq 8]
[ 0.750348] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.750385] pnp 00:07: [io 0x0454-0x0457]
[ 0.750431] system 00:07: [io 0x0454-0x0457] has been reserved
[ 0.750435] system 00:07: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 0.750455] pnp 00:08: [io 0x0060]
[ 0.750460] pnp 00:08: [io 0x0064]
[ 0.750466] pnp 00:08: [irq 1]
[ 0.750501] pnp 00:08: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.750523] pnp 00:09: [irq 12]
[ 0.750554] pnp 00:09: Plug and Play ACPI device, IDs PNP0f13 (active)
[ 0.750718] pnp 00:0a: [mem 0xfed1c000-0xfed1ffff]
[ 0.750721] pnp 00:0a: [mem 0xfed10000-0xfed17fff]
[ 0.750723] pnp 00:0a: [mem 0xfed18000-0xfed18fff]
[ 0.750726] pnp 00:0a: [mem 0xfed19000-0xfed19fff]
[ 0.750729] pnp 00:0a: [mem 0xf8000000-0xfbffffff]
[ 0.750732] pnp 00:0a: [mem 0xfed20000-0xfed3ffff]
[ 0.750734] pnp 00:0a: [mem 0xfed90000-0xfed93fff]
[ 0.750737] pnp 00:0a: [mem 0xfed45000-0xfed8ffff]
[ 0.750740] pnp 00:0a: [mem 0xff000000-0xffffffff]
[ 0.750742] pnp 00:0a: [mem 0xfee00000-0xfeefffff]
[ 0.750746] pnp 00:0a: [mem 0x00000000-0xffffffffffffffff disabled]
[ 0.750800] system 00:0a: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.750804] system 00:0a: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.750807] system 00:0a: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.750811] system 00:0a: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.750815] system 00:0a: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.750818] system 00:0a: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.750822] system 00:0a: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.750825] system 00:0a: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.750829] system 00:0a: [mem 0xff000000-0xffffffff] could not be reserved
[ 0.750833] system 00:0a: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.750837] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.751343] pnp 00:0b: can't evaluate _CRS: 12311
[ 0.751470] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.751547] pnp: PnP ACPI: found 12 devices
[ 0.751549] ACPI: ACPI bus type pnp unregistered
[ 0.757981] PCI: max bus depth: 1 pci_try_num: 2
[ 0.758028] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 0.758031] pci 0000:00:1c.0: bridge window [io disabled]
[ 0.758040] pci 0000:00:1c.0: bridge window [mem 0x90600000-0x906fffff]
[ 0.758047] pci 0000:00:1c.0: bridge window [mem pref disabled]
[ 0.758058] pci 0000:00:1c.3: PCI bridge to [bus 02-02]
[ 0.758063] pci 0000:00:1c.3: bridge window [io 0x2000-0x2fff]
[ 0.758072] pci 0000:00:1c.3: bridge window [mem disabled]
[ 0.758079] pci 0000:00:1c.3: bridge window [mem 0x90400000-0x904fffff 64bit pref]
[ 0.758090] pci 0000:00:1c.4: PCI bridge to [bus 03-03]
[ 0.758092] pci 0000:00:1c.4: bridge window [io disabled]
[ 0.758101] pci 0000:00:1c.4: bridge window [mem 0x90500000-0x905fffff]
[ 0.758108] pci 0000:00:1c.4: bridge window [mem pref disabled]
[ 0.758132] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.758140] pci 0000:00:1c.0: setting latency timer to 64
[ 0.758153] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.758160] pci 0000:00:1c.3: setting latency timer to 64
[ 0.758170] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.758176] pci 0000:00:1c.4: setting latency timer to 64
[ 0.758182] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.758186] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.758189] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.758192] pci_bus 0000:00: resource 7 [mem 0x7f200000-0xfeafffff]
[ 0.758196] pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfed44fff]
[ 0.758199] pci_bus 0000:01: resource 1 [mem 0x90600000-0x906fffff]
[ 0.758203] pci_bus 0000:02: resource 0 [io 0x2000-0x2fff]
[ 0.758206] pci_bus 0000:02: resource 2 [mem 0x90400000-0x904fffff 64bit pref]
[ 0.758210] pci_bus 0000:03: resource 1 [mem 0x90500000-0x905fffff]
[ 0.758296] NET: Registered protocol family 2
[ 0.758520] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.759783] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.760974] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.761199] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.761202] TCP reno registered
[ 0.761218] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.761236] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.761569] NET: Registered protocol family 1
[ 0.761587] pci 0000:00:02.0: Boot video device
[ 0.776653] PCI: CLS 64 bytes, default 64
[ 0.776708] Unpacking initramfs...
[ 0.825513] Freeing initrd memory: 2192k freed
[ 0.826017] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.826022] Placing 64MB software IO TLB between ffff880073c00000 - ffff880077c00000
[ 0.826026] software IO TLB at phys 0x73c00000 - 0x77c00000
[ 0.826654] audit: initializing netlink socket (disabled)
[ 0.826667] type=2000 audit(1319322690.663:1): initialized
[ 0.830289] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.839042] VFS: Disk quotas dquot_6.5.2
[ 0.839231] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.839454] msgmni has been set to 3713
[ 0.839756] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.839807] io scheduler noop registered
[ 0.839809] io scheduler deadline registered
[ 0.839880] io scheduler cfq registered (default)
[ 0.840339] intel_idle: MWAIT substates: 0x21120
[ 0.840342] intel_idle: v0.4 model 0x2A
[ 0.840344] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 0.840393] ERST: Table is not found!
[ 0.840464] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.055246] Linux agpgart interface v0.103
[ 1.055347] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:SPAD] at 0x60,0x64 irq 1,12
[ 1.058245] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.058285] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.058386] mousedev: PS/2 mouse device common for all mice
[ 1.058589] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 1.058621] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 1.058791] cpuidle: using governor ladder
[ 1.059054] cpuidle: using governor menu
[ 1.059314] TCP cubic registered
[ 1.059317] NET: Registered protocol family 17
[ 1.059326] Registering the dns_resolver key type
[ 1.059433] PM: Checking hibernation image partition /dev/sda2
[ 1.091500] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 1.096393] PM: Hibernation image not present or could not be loaded.
[ 1.096412] registered taskstats version 1
[ 1.100139] rtc_cmos 00:06: setting system clock to 2011-10-22 22:31:31 UTC (1319322691)
[ 1.100219] Initializing network drop monitor service
[ 1.102440] Freeing unused kernel memory: 712k freed
[ 1.102583] Write protecting the kernel read-only data: 6144k
[ 1.102920] Freeing unused kernel memory: 12k freed
[ 1.106891] Freeing unused kernel memory: 776k freed
[ 1.130889] udevd[76]: starting version 173
[ 1.137284] SCSI subsystem initialized
[ 1.143176] libata version 3.00 loaded.
[ 1.144939] ahci 0000:00:1f.2: version 3.0
[ 1.144958] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.145042] ahci 0000:00:1f.2: irq 40 for MSI/MSI-X
[ 1.145088] ahci: SSS flag set, parallel bus scan disabled
[ 1.158285] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x19 impl SATA mode
[ 1.158293] ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck stag pm led clo pio slum part ems sxs apst
[ 1.158302] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.174277] scsi0 : ahci
[ 1.174593] scsi1 : ahci
[ 1.174948] scsi2 : ahci
[ 1.175374] scsi3 : ahci
[ 1.175545] scsi4 : ahci
[ 1.175729] scsi5 : ahci
[ 1.176069] ata1: SATA max UDMA/133 abar m2048@0x90708000 port 0x90708100 irq 40
[ 1.176074] ata2: DUMMY
[ 1.176077] ata3: DUMMY
[ 1.176081] ata4: SATA max UDMA/133 abar m2048@0x90708000 port 0x90708280 irq 40
[ 1.176088] ata5: SATA max UDMA/133 abar m2048@0x90708000 port 0x90708300 irq 40
[ 1.176092] ata6: DUMMY
[ 1.494727] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.500042] ata1.00: ATA-8: SAMSUNG MZMPA064HMDR-00000, AXM1701Q, max UDMA/133
[ 1.500048] ata1.00: 125045424 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.501411] ata1.00: configured for UDMA/133
[ 1.501740] scsi 0:0:0:0: Direct-Access ATA SAMSUNG MZMPA064 AXM1 PQ: 0 ANSI: 5
[ 1.505239] sd 0:0:0:0: [sda] 125045424 512-byte logical blocks: (64.0 GB/59.6 GiB)
[ 1.505314] sd 0:0:0:0: [sda] Write Protect is off
[ 1.505318] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.505341] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.505979] sda: sda1 sda2 sda3 sda4
[ 1.506507] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.821190] ata4: SATA link down (SStatus 0 SControl 300)
[ 1.827845] Refined TSC clocksource calibration: 1297.055 MHz.
[ 1.827853] Switching to clocksource tsc
[ 2.140992] ata5: SATA link down (SStatus 0 SControl 300)
[ 2.146517] usbcore: registered new interface driver usbfs
[ 2.146545] usbcore: registered new interface driver hub
[ 2.146596] usbcore: registered new device driver usb
[ 2.148825] xhci_hcd 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.148870] xhci_hcd 0000:03:00.0: setting latency timer to 64
[ 2.148877] xhci_hcd 0000:03:00.0: xHCI Host Controller
[ 2.148940] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 1
[ 2.149130] xhci_hcd 0000:03:00.0: irq 16, io mem 0x90500000
[ 2.149219] xhci_hcd 0000:03:00.0: irq 41 for MSI/MSI-X
[ 2.149224] xhci_hcd 0000:03:00.0: irq 42 for MSI/MSI-X
[ 2.149228] xhci_hcd 0000:03:00.0: irq 43 for MSI/MSI-X
[ 2.149233] xhci_hcd 0000:03:00.0: irq 44 for MSI/MSI-X
[ 2.149237] xhci_hcd 0000:03:00.0: irq 45 for MSI/MSI-X
[ 2.149498] xHCI xhci_add_endpoint called for root hub
[ 2.149502] xHCI xhci_check_bandwidth called for root hub
[ 2.149561] hub 1-0:1.0: USB hub found
[ 2.149574] hub 1-0:1.0: 2 ports detected
[ 2.149712] xhci_hcd 0000:03:00.0: xHCI Host Controller
[ 2.149721] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 2
[ 2.152641] xHCI xhci_add_endpoint called for root hub
[ 2.152645] xHCI xhci_check_bandwidth called for root hub
[ 2.152731] hub 2-0:1.0: USB hub found
[ 2.152744] hub 2-0:1.0: 2 ports detected
[ 2.154447] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.154500] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.154539] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[ 2.154544] ehci_hcd 0000:00:1a.0: EHCI Host Controller
[ 2.154562] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 2.154600] ehci_hcd 0000:00:1a.0: debug port 2
[ 2.158490] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
[ 2.158506] ehci_hcd 0000:00:1a.0: irq 16, io mem 0x9070a000
[ 2.170903] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 2.171099] hub 3-0:1.0: USB hub found
[ 2.171107] hub 3-0:1.0: 2 ports detected
[ 2.171280] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 2.171311] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 2.171316] ehci_hcd 0000:00:1d.0: EHCI Host Controller
[ 2.171329] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
[ 2.171363] ehci_hcd 0000:00:1d.0: debug port 2
[ 2.175265] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
[ 2.175290] ehci_hcd 0000:00:1d.0: irq 23, io mem 0x90709000
[ 2.187543] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 2.187838] hub 4-0:1.0: USB hub found
[ 2.187848] hub 4-0:1.0: 2 ports detected
[ 2.454138] usb 1-1: new low speed USB device number 2 using xhci_hcd
[ 2.491477] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 2.497381] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 2.501096] EXT4-fs (sda3): INFO: recovery required on readonly filesystem
[ 2.501101] EXT4-fs (sda3): write access will be enabled during recovery
[ 2.502374] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 2.503530] usb 1-1: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 2.503537] usb 1-1: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 2.510381] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 2.521338] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint
[ 2.532631] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1c.4/0000:03:00.0/usb1/1-1/1-1:1.0/input/input1
[ 2.532723] generic-usb 0003:046D:C521.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:03:00.0-1/input0
[ 2.534325] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint
[ 2.548360] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 2.551374] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 2.556348] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 2.556641] EXT4-fs (sda3): recovery complete
[ 2.556804] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 2.557608] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1c.4/0000:03:00.0/usb1/1-1/1-1:1.1/input/input2
[ 2.557806] generic-usb 0003:046D:C521.0002: input,hiddev0,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:03:00.0-1/input1
[ 2.557851] usbcore: registered new interface driver usbhid
[ 2.557855] usbhid: USB HID core driver
[ 2.617375] usb 3-1: new high speed USB device number 2 using ehci_hcd
[ 2.741324] hub 3-1:1.0: USB hub found
[ 2.741520] hub 3-1:1.0: 6 ports detected
[ 2.847237] usb 4-1: new high speed USB device number 2 using ehci_hcd
[ 2.971123] hub 4-1:1.0: USB hub found
[ 2.971177] hub 4-1:1.0: 6 ports detected
[ 3.037214] usb 3-1.4: new high speed USB device number 3 using ehci_hcd
[ 3.091996] udevd[265]: starting version 173
[ 3.155751] ACPI: acpi_idle yielding to intel_idle
[ 3.158196] mei: module is from the staging directory, the quality is unknown, you have been warned.
[ 3.161195] agpgart-intel 0000:00:00.0: Intel Sandybridge Chipset
[ 3.161462] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
[ 3.163625] agpgart-intel 0000:00:00.0: detected 65536K stolen memory
[ 3.167374] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x80000000
[ 3.169264] mei 0000:00:16.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.169277] mei 0000:00:16.0: setting latency timer to 64
[ 3.173510] ACPI: Fan [FAN0] (off)
[ 3.173973] ACPI: Fan [FAN1] (off)
[ 3.174068] ACPI: Fan [FAN2] (off)
[ 3.174141] ACPI: Fan [FAN3] (off)
[ 3.174217] ACPI: Fan [FAN4] (off)
[ 3.178420] ACPI: AC Adapter [ADP1] (on-line)
[ 3.178667] thermal LNXTHERM:00: registered as thermal_zone0
[ 3.178673] ACPI: Thermal Zone [TZ00] (58 C)
[ 3.179302] thermal LNXTHERM:01: registered as thermal_zone1
[ 3.179307] ACPI: Thermal Zone [TZ01] (30 C)
[ 3.181648] iTCO_vendor_support: vendor-support=0
[ 3.182776] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input3
[ 3.182838] ACPI: Lid Switch [LID0]
[ 3.182948] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
[ 3.182958] ACPI: Power Button [PWRB]
[ 3.183045] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input5
[ 3.183052] ACPI: Sleep Button [SLPB]
[ 3.183148] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input6
[ 3.183156] ACPI: Power Button [PWRF]
[ 3.188593] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
[ 3.188905] iTCO_wdt: Found a Cougar Point TCO device (Version=2, TCOBASE=0x0460)
[ 3.189082] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 3.196126] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 3.196159] r8169 0000:02:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 3.196245] r8169 0000:02:00.0: setting latency timer to 64
[ 3.196256] r8169 0000:02:00.0: (unregistered net_device): unknown MAC, using family default
[ 3.196364] r8169 0000:02:00.0: irq 46 for MSI/MSI-X
[ 3.213950] [drm] Initialized drm 1.1.0 20060810
[ 3.217549] r8169 0000:02:00.0: eth0: RTL8168b/8111b at 0xffffc90000360000, e8:11:32:77:38:2f, XID 0c900800 IRQ 46
[ 3.217671] cfg80211: Calling CRDA to update world regulatory domain
[ 3.230916] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 3.231023] HDA Intel 0000:00:1b.0: irq 47 for MSI/MSI-X
[ 3.231068] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 3.236095] brcmutil: module is from the staging directory, the quality is unknown, you have been warned.
[ 3.256095] ACPI: Battery Slot [BAT1] (battery present)
[ 3.260805] brcmsmac: module is from the staging directory, the quality is unknown, you have been warned.
[ 3.268555] wmi: Mapper loaded
[ 3.273793] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.274473] brcmsmac 0000:01:00.0: bus 1 slot 0 func 0 irq 11
[ 3.274526] brcmsmac 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.274538] brcmsmac 0000:01:00.0: setting latency timer to 64
[ 3.280464] input: PC Speaker as /devices/platform/pcspkr/input/input7
[ 3.381804] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 3.468535] Linux media interface: v0.10
[ 3.472584] Linux video capture interface: v2.00
[ 3.476090] uvcvideo: Found UVC 1.00 device WebCam SC-13HDL10B31N (2232:1012)
[ 3.495699] input: WebCam SC-13HDL10B31N as /devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.4/3-1.4:1.0/input/input8
[ 3.495876] usbcore: registered new interface driver uvcvideo
[ 3.495885] USB Video Class driver (v1.1.0)
[ 3.523669] usb 4-1.3: new full speed USB device number 3 using ehci_hcd
[ 3.629495] Bluetooth: Core ver 2.16
[ 3.629633] NET: Registered protocol family 31
[ 3.629637] Bluetooth: HCI device and connection manager initialized
[ 3.629641] Bluetooth: HCI socket layer initialized
[ 3.629645] Bluetooth: L2CAP socket layer initialized
[ 3.629758] Bluetooth: SCO socket layer initialized
[ 3.631920] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 3.632198] usbcore: registered new interface driver btusb
[ 3.780683] hda_codec: ALC269VB: BIOS auto-probing.
[ 3.785509] HDMI status: Pin=5 Presence_Detect=0 ELD_Valid=0
[ 3.788196] input: HDA Intel PCH HDMI/DP as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 3.788318] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 3.788431] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[ 3.788746] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.788753] i915 0000:00:02.0: setting latency timer to 64
[ 3.879455] mtrr: no more MTRRs available
[ 3.879460] [drm] MTRR allocation failed. Graphics performance may suffer.
[ 3.879870] i915 0000:00:02.0: irq 48 for MSI/MSI-X
[ 3.879877] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 3.879879] [drm] Driver supports precise vblank timestamp query.
[ 3.879926] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 4.049455] Synaptics Touchpad, model: 1, fw: 8.0, id: 0x1e2b1, caps: 0xd00123/0x840300/0x120c00
[ 4.086894] fbcon: inteldrmfb (fb0) is primary device
[ 4.091216] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input12
[ 4.256322] Console: switching to colour frame buffer device 170x48
[ 4.260265] fb0: inteldrmfb frame buffer device
[ 4.260268] drm: registered panic notifier
[ 4.291118] acpi device:34: registered as cooling_device9
[ 4.291437] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input13
[ 4.291501] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 4.291577] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 4.291636] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 4.857453] EXT4-fs (sda3): re-mounted. Opts: (null)
[ 4.873110] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
[ 4.881576] Adding 2441212k swap on /dev/sda2. Priority:-1 extents:1 across:2441212k SSOffline
#4 2011-10-22 23:04:56
- Gusar
- Member
- Registered: 2009-08-25
- Posts: 3,605
Re: [SOLVED] wpa_supplicant causes system to crash
What do you mean by "it breaks"? Do you even know what ctrl+c does?
I expected a bit more from dmesg, but maybe the brcmsmac driver simply isn't very chatty. Though, when did you run dmesg, did you do it after things "break"?
Last edited by Gusar (2011-10-22 23:05:09)
Offline
#5 2011-10-22 23:54:45
- Revestek
- Member
- Registered: 2011-10-22
- Posts: 5
Re: [SOLVED] wpa_supplicant causes system to crash
Sorry for being unclear. When I said that it breaks, I meant that it returns to the same state that it was in before, ie. the wired network doesn't work and I have to hard reboot to get it back.
I see now that I didn't include everything in the previous dmesg output, so I ran it again (no ctrl+c, wired network still working):
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.0-ARCH (tobias@T-POWA-LX) (gcc version 4.6.1 20110819 (prerelease) (GCC) ) #1 SMP PREEMPT Wed Oct 19 10:27:51 CEST 2011
[ 0.000000] Command line: root=/dev/sda3 rootfstype=ext4 resume=/dev/sda2 ro
[ 0.000000] Disabled fast string operations
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009d800 (usable)
[ 0.000000] BIOS-e820: 000000000009d800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007a3ef000 (usable)
[ 0.000000] BIOS-e820: 000000007a3ef000 - 000000007a6ef000 (reserved)
[ 0.000000] BIOS-e820: 000000007a6ef000 - 000000007a79f000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007a79f000 - 000000007a7ff000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007a7ff000 - 000000007a800000 (usable)
[ 0.000000] BIOS-e820: 000000007a800000 - 000000007f200000 (reserved)
[ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed08000 - 00000000fed09000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed10000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffd80000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000100600000 (usable)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.6 present.
[ 0.000000] DMI: SAMSUNG ELECTRONICS CO., LTD. 900X1B/900X1B, BIOS 01FQ 06/09/2011
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x100600 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0FFC00000 mask FFFC00000 write-protect
[ 0.000000] 1 base 000000000 mask F80000000 write-back
[ 0.000000] 2 base 07C000000 mask FFC000000 uncachable
[ 0.000000] 3 base 07B000000 mask FFF000000 uncachable
[ 0.000000] 4 base 07A800000 mask FFF800000 uncachable
[ 0.000000] 5 base 100000000 mask FE0000000 write-back
[ 0.000000] 6 base 110000000 mask FF0000000 uncachable
[ 0.000000] 7 base 108000000 mask FF8000000 uncachable
[ 0.000000] 8 base 104000000 mask FFC000000 uncachable
[ 0.000000] 9 base 102000000 mask FFE000000 uncachable
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] last_pfn = 0x7a800 max_arch_pfn = 0x400000000
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 20480
[ 0.000000] init_memory_mapping: 0000000000000000-000000007a800000
[ 0.000000] 0000000000 - 007a800000 page 2M
[ 0.000000] kernel direct mapping tables up to 7a800000 @ 7a3ec000-7a3ef000
[ 0.000000] init_memory_mapping: 0000000100000000-0000000100600000
[ 0.000000] 0100000000 - 0100600000 page 2M
[ 0.000000] kernel direct mapping tables up to 100600000 @ 1005fa000-100600000
[ 0.000000] RAMDISK: 37dcc000 - 37ff0000
[ 0.000000] ACPI: RSDP 00000000000f00e0 00024 (v02 SECCSD)
[ 0.000000] ACPI: XSDT 000000007a7fe120 00084 (v01 SECCSD LH43STAR 00000002 PTEC 00000002)
[ 0.000000] ACPI: FACP 000000007a7ef000 000F4 (v03 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: DSDT 000000007a7f2000 0828A (v02 SECCSD SNB-CPT 00000000 INTL 20061109)
[ 0.000000] ACPI: FACS 000000007a73e000 00040
[ 0.000000] ACPI: SLIC 000000007a7fd000 00176 (v01 SECCSD LH43STAR 00000002 PTEC 00000001)
[ 0.000000] ACPI: SSDT 000000007a7fb000 01068 (v01 SECCSD PtidDevc 00001000 INTL 20061109)
[ 0.000000] ACPI: ASF! 000000007a7f1000 000A5 (v32 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: HPET 000000007a7ee000 00038 (v01 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: APIC 000000007a7ed000 00098 (v01 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: MCFG 000000007a7ec000 0003C (v01 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: SSDT 000000007a7eb000 006FC (v01 PmRef Cpu0Ist 00003000 INTL 20061109)
[ 0.000000] ACPI: SSDT 000000007a7ea000 00996 (v01 PmRef CpuPm 00003000 INTL 20061109)
[ 0.000000] ACPI: UEFI 000000007a7e9000 0003E (v01 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: UEFI 000000007a7e8000 00042 (v01 PTL COMBUF 00000001 PTL 00000001)
[ 0.000000] ACPI: UEFI 000000007a7e7000 00256 (v01 SECCSD LH43STAR 00000002 PTL 00000002)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-0000000100600000
[ 0.000000] Initmem setup node 0 0000000000000000-0000000100600000
[ 0.000000] NODE_DATA [00000001005fb000 - 00000001005fffff]
[ 0.000000] [ffffea0000000000-ffffea00039fffff] PMD -> [ffff880077c00000-ffff8800799fffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00100600
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[4] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009d
[ 0.000000] 0: 0x00000100 -> 0x0007a3ef
[ 0.000000] 0: 0x0007a7ff -> 0x0007a800
[ 0.000000] 0: 0x00100000 -> 0x00100600
[ 0.000000] On node 0 totalpages: 502141
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 5 pages reserved
[ 0.000000] DMA zone: 3920 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 482344 pages, LIFO batch:31
[ 0.000000] Normal zone: 21 pages used for memmap
[ 0.000000] Normal zone: 1515 pages, LIFO batch:0
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000
[ 0.000000] SMP: Allowing 8 CPUs, 4 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009d000 - 000000000009e000
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 000000007a3ef000 - 000000007a6ef000
[ 0.000000] PM: Registered nosave memory: 000000007a6ef000 - 000000007a79f000
[ 0.000000] PM: Registered nosave memory: 000000007a79f000 - 000000007a7ff000
[ 0.000000] PM: Registered nosave memory: 000000007a800000 - 000000007f200000
[ 0.000000] PM: Registered nosave memory: 000000007f200000 - 00000000f8000000
[ 0.000000] PM: Registered nosave memory: 00000000f8000000 - 00000000fc000000
[ 0.000000] PM: Registered nosave memory: 00000000fc000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
[ 0.000000] PM: Registered nosave memory: 00000000fec01000 - 00000000fed08000
[ 0.000000] PM: Registered nosave memory: 00000000fed08000 - 00000000fed09000
[ 0.000000] PM: Registered nosave memory: 00000000fed09000 - 00000000fed10000
[ 0.000000] PM: Registered nosave memory: 00000000fed10000 - 00000000fed1a000
[ 0.000000] PM: Registered nosave memory: 00000000fed1a000 - 00000000fed1c000
[ 0.000000] PM: Registered nosave memory: 00000000fed1c000 - 00000000fed20000
[ 0.000000] PM: Registered nosave memory: 00000000fed20000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ffd80000
[ 0.000000] PM: Registered nosave memory: 00000000ffd80000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at 7f200000 (gap: 7f200000:78e00000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 27 pages/cpu @ffff880100200000 s78464 r8192 d23936 u262144
[ 0.000000] pcpu-alloc: s78464 r8192 d23936 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 487779
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: root=/dev/sda3 rootfstype=ext4 resume=/dev/sda2 ro
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave/xrstor: enabled xstate_bv 0x7, cntxt size 0x340
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 1899028k/4200448k available (4066k kernel code, 2191884k absent, 109536k reserved, 3302k data, 712k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:2304
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 17825792 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.003333] Detected 1297.092 MHz processor.
[ 0.000004] Calibrating delay loop (skipped), value calculated using timer frequency.. 2595.27 BogoMIPS (lpj=4323640)
[ 0.000010] pid_max: default: 32768 minimum: 301
[ 0.000200] Security Framework initialized
[ 0.000205] AppArmor: AppArmor disabled by boot time parameter
[ 0.000591] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.001435] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.001784] Mount-cache hash table entries: 256
[ 0.002308] Initializing cgroup subsys cpuacct
[ 0.002354] Initializing cgroup subsys memory
[ 0.002378] Initializing cgroup subsys devices
[ 0.002382] Initializing cgroup subsys freezer
[ 0.002384] Initializing cgroup subsys net_cls
[ 0.002387] Initializing cgroup subsys blkio
[ 0.002462] Disabled fast string operations
[ 0.002465] CPU: Physical Processor ID: 0
[ 0.002468] CPU: Processor Core ID: 0
[ 0.002476] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.002477] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.002482] mce: CPU supports 7 MCE banks
[ 0.002501] CPU0: Thermal monitoring enabled (TM1)
[ 0.002513] using mwait in idle threads.
[ 0.003881] ACPI: Core revision 20110413
[ 0.018424] ftrace: allocating 16144 entries in 64 pages
[ 0.027846] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.060836] CPU0: Intel(R) Core(TM) i3-2357M CPU @ 1.30GHz stepping 07
[ 0.167197] Performance Events: PEBS fmt1+, SandyBridge events, Intel PMU driver.
[ 0.167206] ... version: 3
[ 0.167208] ... bit width: 48
[ 0.167210] ... generic registers: 4
[ 0.167212] ... value mask: 0000ffffffffffff
[ 0.167215] ... max period: 000000007fffffff
[ 0.167217] ... fixed-purpose events: 3
[ 0.167219] ... event mask: 000000070000000f
[ 0.187380] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.213860] Booting Node 0, Processors #1
[ 0.213866] smpboot cpu 1: start_ip = 98000
[ 0.307128] Disabled fast string operations
[ 0.327221] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.347134] #2
[ 0.347138] smpboot cpu 2: start_ip = 98000
[ 0.440378] Disabled fast string operations
[ 0.460456] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.480378] #3
[ 0.480382] smpboot cpu 3: start_ip = 98000
[ 0.573628] Disabled fast string operations
[ 0.593695] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.600273] Brought up 4 CPUs
[ 0.600278] Total of 4 processors activated (10380.91 BogoMIPS).
[ 0.604581] devtmpfs: initialized
[ 0.605760] PM: Registering ACPI NVS region at 7a6ef000 (720896 bytes)
[ 0.607029] print_constraints: dummy:
[ 0.607142] NET: Registered protocol family 16
[ 0.607284] ACPI: bus type pci registered
[ 0.607518] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.607523] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.625490] PCI: Using configuration type 1 for base access
[ 0.626152] bio: create slab <bio-0> at 0
[ 0.628540] ACPI: EC: Look up EC in DSDT
[ 0.630694] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.650335] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.661422] ACPI: SSDT 000000007a6e0718 00670 (v01 PmRef Cpu0Cst 00003001 INTL 20061109)
[ 0.661969] ACPI: Dynamic OEM Table Load:
[ 0.661974] ACPI: SSDT (null) 00670 (v01 PmRef Cpu0Cst 00003001 INTL 20061109)
[ 0.670598] ACPI: SSDT 000000007a6e1a98 00303 (v01 PmRef ApIst 00003000 INTL 20061109)
[ 0.671185] ACPI: Dynamic OEM Table Load:
[ 0.671188] ACPI: SSDT (null) 00303 (v01 PmRef ApIst 00003000 INTL 20061109)
[ 0.680383] ACPI: SSDT 000000007a6dfd98 00119 (v01 PmRef ApCst 00003000 INTL 20061109)
[ 0.680919] ACPI: Dynamic OEM Table Load:
[ 0.680922] ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000 INTL 20061109)
[ 0.693655] ACPI: Interpreter enabled
[ 0.693661] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.693697] ACPI: Using IOAPIC for interrupt routing
[ 0.713158] ACPI: Power Resource [FN00] (off)
[ 0.713278] ACPI: Power Resource [FN01] (off)
[ 0.713393] ACPI: Power Resource [FN02] (off)
[ 0.713512] ACPI: Power Resource [FN03] (off)
[ 0.713637] ACPI: Power Resource [FN04] (off)
[ 0.714084] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[ 0.714334] ACPI: No dock devices found.
[ 0.714337] HEST: Table not found.
[ 0.714341] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.715026] \_SB_.PCI0:_OSC invalid UUID
[ 0.715028] _OSC request data:1 8 1f
[ 0.715034] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 0.715875] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 0.715879] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 0.715883] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.715888] pci_root PNP0A08:00: host bridge window [mem 0x7f200000-0xfeafffff]
[ 0.715891] pci_root PNP0A08:00: host bridge window [mem 0xfed40000-0xfed44fff]
[ 0.715908] pci 0000:00:00.0: [8086:0104] type 0 class 0x000600
[ 0.715962] pci 0000:00:02.0: [8086:0116] type 0 class 0x000300
[ 0.715980] pci 0000:00:02.0: reg 10: [mem 0x90000000-0x903fffff 64bit]
[ 0.715990] pci 0000:00:02.0: reg 18: [mem 0x80000000-0x8fffffff 64bit pref]
[ 0.715998] pci 0000:00:02.0: reg 20: [io 0x3000-0x303f]
[ 0.716088] pci 0000:00:16.0: [8086:1c3a] type 0 class 0x000780
[ 0.716129] pci 0000:00:16.0: reg 10: [mem 0x90705000-0x9070500f 64bit]
[ 0.716235] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.716242] pci 0000:00:16.0: PME# disabled
[ 0.716301] pci 0000:00:1a.0: [8086:1c2d] type 0 class 0x000c03
[ 0.716337] pci 0000:00:1a.0: reg 10: [mem 0x9070a000-0x9070a3ff]
[ 0.716466] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.716473] pci 0000:00:1a.0: PME# disabled
[ 0.716514] pci 0000:00:1b.0: [8086:1c20] type 0 class 0x000403
[ 0.716545] pci 0000:00:1b.0: reg 10: [mem 0x90700000-0x90703fff 64bit]
[ 0.716655] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.716662] pci 0000:00:1b.0: PME# disabled
[ 0.716699] pci 0000:00:1c.0: [8086:1c10] type 1 class 0x000604
[ 0.716816] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.716823] pci 0000:00:1c.0: PME# disabled
[ 0.716873] pci 0000:00:1c.3: [8086:1c16] type 1 class 0x000604
[ 0.716991] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.716997] pci 0000:00:1c.3: PME# disabled
[ 0.717036] pci 0000:00:1c.4: [8086:1c18] type 1 class 0x000604
[ 0.717153] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.717159] pci 0000:00:1c.4: PME# disabled
[ 0.717215] pci 0000:00:1d.0: [8086:1c26] type 0 class 0x000c03
[ 0.717251] pci 0000:00:1d.0: reg 10: [mem 0x90709000-0x907093ff]
[ 0.717379] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.717386] pci 0000:00:1d.0: PME# disabled
[ 0.717423] pci 0000:00:1f.0: [8086:1c49] type 0 class 0x000601
[ 0.717609] pci 0000:00:1f.2: [8086:1c03] type 0 class 0x000106
[ 0.717650] pci 0000:00:1f.2: reg 10: [io 0x3088-0x308f]
[ 0.717667] pci 0000:00:1f.2: reg 14: [io 0x3094-0x3097]
[ 0.717683] pci 0000:00:1f.2: reg 18: [io 0x3080-0x3087]
[ 0.717699] pci 0000:00:1f.2: reg 1c: [io 0x3090-0x3093]
[ 0.717716] pci 0000:00:1f.2: reg 20: [io 0x3060-0x307f]
[ 0.717733] pci 0000:00:1f.2: reg 24: [mem 0x90708000-0x907087ff]
[ 0.717805] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.717811] pci 0000:00:1f.2: PME# disabled
[ 0.717843] pci 0000:00:1f.3: [8086:1c22] type 0 class 0x000c05
[ 0.717874] pci 0000:00:1f.3: reg 10: [mem 0x90704000-0x907040ff 64bit]
[ 0.717919] pci 0000:00:1f.3: reg 20: [io 0xefa0-0xefbf]
[ 0.718112] pci 0000:01:00.0: [14e4:4357] type 0 class 0x000280
[ 0.718153] pci 0000:01:00.0: reg 10: [mem 0x90600000-0x90603fff 64bit]
[ 0.718316] pci 0000:01:00.0: supports D1 D2
[ 0.718318] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.718326] pci 0000:01:00.0: PME# disabled
[ 0.723594] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 0.723601] pci 0000:00:1c.0: bridge window [io 0xf000-0x0000] (disabled)
[ 0.723609] pci 0000:00:1c.0: bridge window [mem 0x90600000-0x906fffff]
[ 0.723619] pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.723783] pci 0000:02:00.0: [10ec:8168] type 0 class 0x000200
[ 0.723859] pci 0000:02:00.0: reg 10: [io 0x2000-0x20ff]
[ 0.723995] pci 0000:02:00.0: reg 18: [mem 0x90404000-0x90404fff 64bit pref]
[ 0.724079] pci 0000:02:00.0: reg 20: [mem 0x90400000-0x90403fff 64bit pref]
[ 0.724317] pci 0000:02:00.0: supports D1 D2
[ 0.724319] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.724337] pci 0000:02:00.0: PME# disabled
[ 0.730261] pci 0000:00:1c.3: PCI bridge to [bus 02-02]
[ 0.730268] pci 0000:00:1c.3: bridge window [io 0x2000-0x2fff]
[ 0.730275] pci 0000:00:1c.3: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 0.730286] pci 0000:00:1c.3: bridge window [mem 0x90400000-0x904fffff 64bit pref]
[ 0.730403] pci 0000:03:00.0: [1033:0194] type 0 class 0x000c03
[ 0.730441] pci 0000:03:00.0: reg 10: [mem 0x90500000-0x90501fff 64bit]
[ 0.730596] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[ 0.730603] pci 0000:03:00.0: PME# disabled
[ 0.730678] pci 0000:00:1c.4: PCI bridge to [bus 03-03]
[ 0.730685] pci 0000:00:1c.4: bridge window [io 0xf000-0x0000] (disabled)
[ 0.730692] pci 0000:00:1c.4: bridge window [mem 0x90500000-0x905fffff]
[ 0.730703] pci 0000:00:1c.4: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.730734] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.730898] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.730952] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
[ 0.730999] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP05._PRT]
[ 0.731206] \_SB_.PCI0:_OSC invalid UUID
[ 0.731208] _OSC request data:1 1f 1f
[ 0.731214] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.731340] \_SB_.PCI0:_OSC invalid UUID
[ 0.731342] _OSC request data:1 0 1d
[ 0.731348] pci0000:00: ACPI _OSC request failed (AE_ERROR), returned control mask: 0x1d
[ 0.731350] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 0.735055] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[ 0.735124] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.735192] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[ 0.735256] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[ 0.735320] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 *5 6 10 11 12 14 15)
[ 0.735383] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.735447] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[ 0.735511] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 *5 6 10 11 12 14 15)
[ 0.735630] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.735640] vgaarb: loaded
[ 0.735642] vgaarb: bridge control possible 0000:00:02.0
[ 0.735743] PCI: Using ACPI for IRQ routing
[ 0.739377] PCI: pci_cache_line_size set to 64 bytes
[ 0.739494] reserve RAM buffer: 000000000009d800 - 000000000009ffff
[ 0.739498] reserve RAM buffer: 000000007a3ef000 - 000000007bffffff
[ 0.739501] reserve RAM buffer: 000000007a800000 - 000000007bffffff
[ 0.739504] reserve RAM buffer: 0000000100600000 - 0000000103ffffff
[ 0.739661] NetLabel: Initializing
[ 0.739663] NetLabel: domain hash size = 128
[ 0.739665] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.739686] NetLabel: unlabeled traffic allowed by default
[ 0.739706] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.739715] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.741737] Switching to clocksource hpet
[ 0.743524] Switched to NOHz mode on CPU #0
[ 0.743609] Switched to NOHz mode on CPU #3
[ 0.743622] Switched to NOHz mode on CPU #2
[ 0.743634] Switched to NOHz mode on CPU #1
[ 0.748960] pnp: PnP ACPI init
[ 0.748979] ACPI: bus type pnp registered
[ 0.749439] pnp 00:00: [bus 00-3e]
[ 0.749442] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.749446] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.749449] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.749452] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.749455] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 0.749458] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 0.749461] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 0.749464] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 0.749467] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 0.749470] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 0.749475] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 0.749478] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 0.749481] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[ 0.749485] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[ 0.749488] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[ 0.749491] pnp 00:00: [mem 0x000ec000-0x000effff window]
[ 0.749494] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[ 0.749497] pnp 00:00: [mem 0x7f200000-0xfeafffff window]
[ 0.749500] pnp 00:00: [mem 0xfed40000-0xfed44fff window]
[ 0.749593] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.749928] pnp 00:01: [io 0x0000-0x001f]
[ 0.749931] pnp 00:01: [io 0x0081-0x0091]
[ 0.749933] pnp 00:01: [io 0x0093-0x009f]
[ 0.749936] pnp 00:01: [io 0x00c0-0x00df]
[ 0.749939] pnp 00:01: [dma 4]
[ 0.749973] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.749985] pnp 00:02: [mem 0xff000000-0xffffffff]
[ 0.750014] pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.750115] pnp 00:03: [mem 0xfed00000-0xfed003ff]
[ 0.750153] pnp 00:03: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.750167] pnp 00:04: [io 0x00f0]
[ 0.750178] pnp 00:04: [irq 13]
[ 0.750209] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.750225] pnp 00:05: [io 0x002e-0x002f]
[ 0.750227] pnp 00:05: [io 0x004e-0x004f]
[ 0.750230] pnp 00:05: [io 0x0061]
[ 0.750232] pnp 00:05: [io 0x0063]
[ 0.750234] pnp 00:05: [io 0x0065]
[ 0.750236] pnp 00:05: [io 0x0067]
[ 0.750239] pnp 00:05: [io 0x0070]
[ 0.750241] pnp 00:05: [io 0x0080]
[ 0.750243] pnp 00:05: [io 0x0092]
[ 0.750245] pnp 00:05: [io 0x00b2-0x00b3]
[ 0.750248] pnp 00:05: [io 0x0680-0x069f]
[ 0.750251] pnp 00:05: [io 0x1000-0x100f]
[ 0.750253] pnp 00:05: [io 0x5000-0x5003]
[ 0.750256] pnp 00:05: [io 0xffff]
[ 0.750258] pnp 00:05: [io 0x0400-0x0453]
[ 0.750260] pnp 00:05: [io 0x0458-0x047f]
[ 0.750263] pnp 00:05: [io 0x0500-0x057f]
[ 0.750265] pnp 00:05: [io 0x0a00-0x0a0f]
[ 0.750268] pnp 00:05: [io 0x164e-0x164f]
[ 0.750270] pnp 00:05: [io 0x5000-0x500f]
[ 0.750331] system 00:05: [io 0x0680-0x069f] has been reserved
[ 0.750334] system 00:05: [io 0x1000-0x100f] has been reserved
[ 0.750338] system 00:05: [io 0x5000-0x5003] has been reserved
[ 0.750341] system 00:05: [io 0xffff] has been reserved
[ 0.750344] system 00:05: [io 0x0400-0x0453] has been reserved
[ 0.750348] system 00:05: [io 0x0458-0x047f] has been reserved
[ 0.750351] system 00:05: [io 0x0500-0x057f] has been reserved
[ 0.750355] system 00:05: [io 0x0a00-0x0a0f] has been reserved
[ 0.750358] system 00:05: [io 0x164e-0x164f] has been reserved
[ 0.750362] system 00:05: [io 0x5000-0x500f] could not be reserved
[ 0.750366] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.750378] pnp 00:06: [io 0x0070-0x0077]
[ 0.750384] pnp 00:06: [irq 8]
[ 0.750417] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.750454] pnp 00:07: [io 0x0454-0x0457]
[ 0.750501] system 00:07: [io 0x0454-0x0457] has been reserved
[ 0.750505] system 00:07: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 0.750525] pnp 00:08: [io 0x0060]
[ 0.750530] pnp 00:08: [io 0x0064]
[ 0.750536] pnp 00:08: [irq 1]
[ 0.750571] pnp 00:08: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.750593] pnp 00:09: [irq 12]
[ 0.750624] pnp 00:09: Plug and Play ACPI device, IDs PNP0f13 (active)
[ 0.750789] pnp 00:0a: [mem 0xfed1c000-0xfed1ffff]
[ 0.750791] pnp 00:0a: [mem 0xfed10000-0xfed17fff]
[ 0.750794] pnp 00:0a: [mem 0xfed18000-0xfed18fff]
[ 0.750797] pnp 00:0a: [mem 0xfed19000-0xfed19fff]
[ 0.750800] pnp 00:0a: [mem 0xf8000000-0xfbffffff]
[ 0.750802] pnp 00:0a: [mem 0xfed20000-0xfed3ffff]
[ 0.750805] pnp 00:0a: [mem 0xfed90000-0xfed93fff]
[ 0.750808] pnp 00:0a: [mem 0xfed45000-0xfed8ffff]
[ 0.750810] pnp 00:0a: [mem 0xff000000-0xffffffff]
[ 0.750813] pnp 00:0a: [mem 0xfee00000-0xfeefffff]
[ 0.750816] pnp 00:0a: [mem 0x00000000-0xffffffffffffffff disabled]
[ 0.750870] system 00:0a: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.750874] system 00:0a: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.750877] system 00:0a: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.750881] system 00:0a: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.750885] system 00:0a: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.750888] system 00:0a: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.750892] system 00:0a: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.750895] system 00:0a: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.750899] system 00:0a: [mem 0xff000000-0xffffffff] could not be reserved
[ 0.750903] system 00:0a: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.750907] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.751415] pnp 00:0b: can't evaluate _CRS: 12311
[ 0.751543] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.751620] pnp: PnP ACPI: found 12 devices
[ 0.751622] ACPI: ACPI bus type pnp unregistered
[ 0.758061] PCI: max bus depth: 1 pci_try_num: 2
[ 0.758108] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 0.758111] pci 0000:00:1c.0: bridge window [io disabled]
[ 0.758120] pci 0000:00:1c.0: bridge window [mem 0x90600000-0x906fffff]
[ 0.758127] pci 0000:00:1c.0: bridge window [mem pref disabled]
[ 0.758138] pci 0000:00:1c.3: PCI bridge to [bus 02-02]
[ 0.758143] pci 0000:00:1c.3: bridge window [io 0x2000-0x2fff]
[ 0.758152] pci 0000:00:1c.3: bridge window [mem disabled]
[ 0.758159] pci 0000:00:1c.3: bridge window [mem 0x90400000-0x904fffff 64bit pref]
[ 0.758170] pci 0000:00:1c.4: PCI bridge to [bus 03-03]
[ 0.758173] pci 0000:00:1c.4: bridge window [io disabled]
[ 0.758181] pci 0000:00:1c.4: bridge window [mem 0x90500000-0x905fffff]
[ 0.758188] pci 0000:00:1c.4: bridge window [mem pref disabled]
[ 0.758213] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.758221] pci 0000:00:1c.0: setting latency timer to 64
[ 0.758234] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.758241] pci 0000:00:1c.3: setting latency timer to 64
[ 0.758251] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.758258] pci 0000:00:1c.4: setting latency timer to 64
[ 0.758264] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.758267] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.758270] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.758273] pci_bus 0000:00: resource 7 [mem 0x7f200000-0xfeafffff]
[ 0.758277] pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfed44fff]
[ 0.758280] pci_bus 0000:01: resource 1 [mem 0x90600000-0x906fffff]
[ 0.758284] pci_bus 0000:02: resource 0 [io 0x2000-0x2fff]
[ 0.758287] pci_bus 0000:02: resource 2 [mem 0x90400000-0x904fffff 64bit pref]
[ 0.758290] pci_bus 0000:03: resource 1 [mem 0x90500000-0x905fffff]
[ 0.758377] NET: Registered protocol family 2
[ 0.758602] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.759859] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.761045] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.761268] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.761271] TCP reno registered
[ 0.761288] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.761305] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.761640] NET: Registered protocol family 1
[ 0.761659] pci 0000:00:02.0: Boot video device
[ 0.776954] PCI: CLS 64 bytes, default 64
[ 0.777009] Unpacking initramfs...
[ 0.825852] Freeing initrd memory: 2192k freed
[ 0.826360] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.826365] Placing 64MB software IO TLB between ffff880073c00000 - ffff880077c00000
[ 0.826368] software IO TLB at phys 0x73c00000 - 0x77c00000
[ 0.826996] audit: initializing netlink socket (disabled)
[ 0.827009] type=2000 audit(1319324053.663:1): initialized
[ 0.830631] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.839386] VFS: Disk quotas dquot_6.5.2
[ 0.839574] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.839797] msgmni has been set to 3713
[ 0.840099] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.840150] io scheduler noop registered
[ 0.840152] io scheduler deadline registered
[ 0.840222] io scheduler cfq registered (default)
[ 0.840680] intel_idle: MWAIT substates: 0x21120
[ 0.840683] intel_idle: v0.4 model 0x2A
[ 0.840685] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 0.840734] ERST: Table is not found!
[ 0.840805] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.055304] Linux agpgart interface v0.103
[ 1.055406] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:SPAD] at 0x60,0x64 irq 1,12
[ 1.059090] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.059130] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.059230] mousedev: PS/2 mouse device common for all mice
[ 1.059431] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 1.059463] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 1.059634] cpuidle: using governor ladder
[ 1.059898] cpuidle: using governor menu
[ 1.060159] TCP cubic registered
[ 1.060162] NET: Registered protocol family 17
[ 1.060170] Registering the dns_resolver key type
[ 1.060287] PM: Checking hibernation image partition /dev/sda2
[ 1.092240] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 1.097116] PM: Hibernation image not present or could not be loaded.
[ 1.097134] registered taskstats version 1
[ 1.100859] rtc_cmos 00:06: setting system clock to 2011-10-22 22:54:14 UTC (1319324054)
[ 1.100939] Initializing network drop monitor service
[ 1.103158] Freeing unused kernel memory: 712k freed
[ 1.103302] Write protecting the kernel read-only data: 6144k
[ 1.103637] Freeing unused kernel memory: 12k freed
[ 1.107609] Freeing unused kernel memory: 776k freed
[ 1.131504] udevd[76]: starting version 173
[ 1.137887] SCSI subsystem initialized
[ 1.143893] libata version 3.00 loaded.
[ 1.145794] ahci 0000:00:1f.2: version 3.0
[ 1.145817] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.145916] ahci 0000:00:1f.2: irq 40 for MSI/MSI-X
[ 1.145962] ahci: SSS flag set, parallel bus scan disabled
[ 1.158335] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x19 impl SATA mode
[ 1.158343] ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck stag pm led clo pio slum part ems sxs apst
[ 1.158352] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.175170] scsi0 : ahci
[ 1.175540] scsi1 : ahci
[ 1.175883] scsi2 : ahci
[ 1.176210] scsi3 : ahci
[ 1.176681] scsi4 : ahci
[ 1.176993] scsi5 : ahci
[ 1.177125] ata1: SATA max UDMA/133 abar m2048@0x90708000 port 0x90708100 irq 40
[ 1.177128] ata2: DUMMY
[ 1.177130] ata3: DUMMY
[ 1.177133] ata4: SATA max UDMA/133 abar m2048@0x90708000 port 0x90708280 irq 40
[ 1.177138] ata5: SATA max UDMA/133 abar m2048@0x90708000 port 0x90708300 irq 40
[ 1.177141] ata6: DUMMY
[ 1.494785] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.499638] ata1.00: ATA-8: SAMSUNG MZMPA064HMDR-00000, AXM1701Q, max UDMA/133
[ 1.499645] ata1.00: 125045424 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.501031] ata1.00: configured for UDMA/133
[ 1.501322] scsi 0:0:0:0: Direct-Access ATA SAMSUNG MZMPA064 AXM1 PQ: 0 ANSI: 5
[ 1.505182] sd 0:0:0:0: [sda] 125045424 512-byte logical blocks: (64.0 GB/59.6 GiB)
[ 1.505331] sd 0:0:0:0: [sda] Write Protect is off
[ 1.505339] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.505385] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.506216] sda: sda1 sda2 sda3 sda4
[ 1.506837] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.821244] ata4: SATA link down (SStatus 0 SControl 300)
[ 1.827906] Refined TSC clocksource calibration: 1297.055 MHz.
[ 1.827916] Switching to clocksource tsc
[ 2.141051] ata5: SATA link down (SStatus 0 SControl 300)
[ 2.146792] usbcore: registered new interface driver usbfs
[ 2.146819] usbcore: registered new interface driver hub
[ 2.146878] usbcore: registered new device driver usb
[ 2.149121] xhci_hcd 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.149165] xhci_hcd 0000:03:00.0: setting latency timer to 64
[ 2.149172] xhci_hcd 0000:03:00.0: xHCI Host Controller
[ 2.149241] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 1
[ 2.149435] xhci_hcd 0000:03:00.0: irq 16, io mem 0x90500000
[ 2.149525] xhci_hcd 0000:03:00.0: irq 41 for MSI/MSI-X
[ 2.149531] xhci_hcd 0000:03:00.0: irq 42 for MSI/MSI-X
[ 2.149535] xhci_hcd 0000:03:00.0: irq 43 for MSI/MSI-X
[ 2.149539] xhci_hcd 0000:03:00.0: irq 44 for MSI/MSI-X
[ 2.149544] xhci_hcd 0000:03:00.0: irq 45 for MSI/MSI-X
[ 2.149788] xHCI xhci_add_endpoint called for root hub
[ 2.149792] xHCI xhci_check_bandwidth called for root hub
[ 2.149849] hub 1-0:1.0: USB hub found
[ 2.149862] hub 1-0:1.0: 2 ports detected
[ 2.150012] xhci_hcd 0000:03:00.0: xHCI Host Controller
[ 2.150022] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 2
[ 2.152944] xHCI xhci_add_endpoint called for root hub
[ 2.152948] xHCI xhci_check_bandwidth called for root hub
[ 2.153044] hub 2-0:1.0: USB hub found
[ 2.153056] hub 2-0:1.0: 2 ports detected
[ 2.154767] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.154802] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.154843] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[ 2.154851] ehci_hcd 0000:00:1a.0: EHCI Host Controller
[ 2.154869] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 2.154917] ehci_hcd 0000:00:1a.0: debug port 2
[ 2.158792] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
[ 2.158808] ehci_hcd 0000:00:1a.0: irq 16, io mem 0x9070a000
[ 2.171003] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 2.171212] hub 3-0:1.0: USB hub found
[ 2.171220] hub 3-0:1.0: 2 ports detected
[ 2.171354] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 2.171394] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 2.171402] ehci_hcd 0000:00:1d.0: EHCI Host Controller
[ 2.171419] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
[ 2.171467] ehci_hcd 0000:00:1d.0: debug port 2
[ 2.175353] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
[ 2.175379] ehci_hcd 0000:00:1d.0: irq 23, io mem 0x90709000
[ 2.187606] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 2.187855] hub 4-0:1.0: USB hub found
[ 2.187865] hub 4-0:1.0: 2 ports detected
[ 2.454201] usb 1-1: new low speed USB device number 2 using xhci_hcd
[ 2.490774] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 2.496772] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 2.501768] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 2.502974] usb 1-1: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 2.502985] usb 1-1: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 2.509778] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 2.519661] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint
[ 2.531190] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1c.4/0000:03:00.0/usb1/1-1/1-1:1.0/input/input1
[ 2.531294] generic-usb 0003:046D:C521.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:03:00.0-1/input0
[ 2.532736] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint
[ 2.546749] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 2.549753] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 2.554741] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 2.555943] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1c.4/0000:03:00.0/usb1/1-1/1-1:1.1/input/input2
[ 2.556101] generic-usb 0003:046D:C521.0002: input,hiddev0,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:03:00.0-1/input1
[ 2.556126] usbcore: registered new interface driver usbhid
[ 2.556129] usbhid: USB HID core driver
[ 2.567739] EXT4-fs (sda3): INFO: recovery required on readonly filesystem
[ 2.567744] EXT4-fs (sda3): write access will be enabled during recovery
[ 2.588127] EXT4-fs (sda3): recovery complete
[ 2.588294] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 2.617432] usb 3-1: new high speed USB device number 2 using ehci_hcd
[ 2.741316] hub 3-1:1.0: USB hub found
[ 2.741371] hub 3-1:1.0: 6 ports detected
[ 2.847205] usb 4-1: new high speed USB device number 2 using ehci_hcd
[ 2.896525] udevd[275]: starting version 173
[ 2.954520] ACPI: acpi_idle yielding to intel_idle
[ 2.970198] ACPI: AC Adapter [ADP1] (on-line)
[ 2.971183] hub 4-1:1.0: USB hub found
[ 2.971356] hub 4-1:1.0: 6 ports detected
[ 2.977757] agpgart-intel 0000:00:00.0: Intel Sandybridge Chipset
[ 2.978034] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
[ 2.980179] agpgart-intel 0000:00:00.0: detected 65536K stolen memory
[ 2.980349] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x80000000
[ 2.984494] mei: module is from the staging directory, the quality is unknown, you have been warned.
[ 2.986025] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input3
[ 2.986087] ACPI: Lid Switch [LID0]
[ 2.986404] ACPI: Fan [FAN0] (off)
[ 2.987216] ACPI: Fan [FAN1] (off)
[ 2.987480] mei 0000:00:16.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.987489] mei 0000:00:16.0: setting latency timer to 64
[ 2.989598] ACPI: Fan [FAN2] (off)
[ 2.989648] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
[ 2.989660] ACPI: Power Button [PWRB]
[ 2.989748] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input5
[ 2.989756] ACPI: Sleep Button [SLPB]
[ 2.990985] ACPI: Fan [FAN3] (off)
[ 2.991051] ACPI: Fan [FAN4] (off)
[ 2.991217] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input6
[ 2.991226] ACPI: Power Button [PWRF]
[ 2.994404] thermal LNXTHERM:00: registered as thermal_zone0
[ 2.994410] ACPI: Thermal Zone [TZ00] (57 C)
[ 2.997019] thermal LNXTHERM:01: registered as thermal_zone1
[ 2.997025] ACPI: Thermal Zone [TZ01] (30 C)
[ 3.011928] iTCO_vendor_support: vendor-support=0
[ 3.016996] ACPI: Battery Slot [BAT1] (battery present)
[ 3.019991] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
[ 3.020142] iTCO_wdt: Found a Cougar Point TCO device (Version=2, TCOBASE=0x0460)
[ 3.020239] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 3.033991] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 3.034024] r8169 0000:02:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 3.034118] r8169 0000:02:00.0: setting latency timer to 64
[ 3.034131] r8169 0000:02:00.0: (unregistered net_device): unknown MAC, using family default
[ 3.034239] r8169 0000:02:00.0: irq 46 for MSI/MSI-X
[ 3.036207] wmi: Mapper loaded
[ 3.037254] r8169 0000:02:00.0: eth0: RTL8168b/8111b at 0xffffc9000035a000, e8:11:32:77:38:2f, XID 0c900800 IRQ 46
[ 3.052026] input: PC Speaker as /devices/platform/pcspkr/input/input7
[ 3.053464] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.053965] cfg80211: Calling CRDA to update world regulatory domain
[ 3.055448] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 3.062580] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 3.062710] HDA Intel 0000:00:1b.0: irq 47 for MSI/MSI-X
[ 3.062759] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 3.063933] usb 3-1.4: new high speed USB device number 3 using ehci_hcd
[ 3.071272] brcmutil: module is from the staging directory, the quality is unknown, you have been warned.
[ 3.092328] brcmsmac: module is from the staging directory, the quality is unknown, you have been warned.
[ 3.095068] brcmsmac 0000:01:00.0: bus 1 slot 0 func 0 irq 11
[ 3.095119] brcmsmac 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.095131] brcmsmac 0000:01:00.0: setting latency timer to 64
[ 3.114082] [drm] Initialized drm 1.1.0 20060810
[ 3.181173] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 3.495242] Linux media interface: v0.10
[ 3.499312] Linux video capture interface: v2.00
[ 3.503007] uvcvideo: Found UVC 1.00 device WebCam SC-13HDL10B31N (2232:1012)
[ 3.522740] input: WebCam SC-13HDL10B31N as /devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.4/3-1.4:1.0/input/input8
[ 3.522912] usbcore: registered new interface driver uvcvideo
[ 3.522919] USB Video Class driver (v1.1.0)
[ 3.550329] usb 4-1.3: new full speed USB device number 3 using ehci_hcd
[ 3.610683] hda_codec: ALC269VB: BIOS auto-probing.
[ 3.614907] HDMI status: Pin=5 Presence_Detect=0 ELD_Valid=0
[ 3.617599] input: HDA Intel PCH HDMI/DP as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 3.617722] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 3.617842] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[ 3.618121] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.618127] i915 0000:00:02.0: setting latency timer to 64
[ 3.657973] Bluetooth: Core ver 2.16
[ 3.657998] NET: Registered protocol family 31
[ 3.658001] Bluetooth: HCI device and connection manager initialized
[ 3.658006] Bluetooth: HCI socket layer initialized
[ 3.658009] Bluetooth: L2CAP socket layer initialized
[ 3.661472] Bluetooth: SCO socket layer initialized
[ 3.663707] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 3.664407] usbcore: registered new interface driver btusb
[ 3.720204] mtrr: no more MTRRs available
[ 3.720210] [drm] MTRR allocation failed. Graphics performance may suffer.
[ 3.720608] i915 0000:00:02.0: irq 48 for MSI/MSI-X
[ 3.720615] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 3.720617] [drm] Driver supports precise vblank timestamp query.
[ 3.720666] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 3.821803] Synaptics Touchpad, model: 1, fw: 8.0, id: 0x1e2b1, caps: 0xd00123/0x840300/0x120c00
[ 3.863428] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input12
[ 3.927177] fbcon: inteldrmfb (fb0) is primary device
[ 4.093147] Console: switching to colour frame buffer device 170x48
[ 4.097088] fb0: inteldrmfb frame buffer device
[ 4.097091] drm: registered panic notifier
[ 4.127876] acpi device:34: registered as cooling_device9
[ 4.128226] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input13
[ 4.128281] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 4.128372] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 4.547119] EXT4-fs (sda3): re-mounted. Opts: (null)
[ 4.563155] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
[ 4.571769] Adding 2441212k swap on /dev/sda2. Priority:-1 extents:1 across:2441212k SS
[ 5.276395] r8169 0000:02:00.0: eth0: link down
[ 5.276406] r8169 0000:02:00.0: eth0: link down
[ 7.619952] r8169 0000:02:00.0: eth0: link up
[ 2470.852087] NET: Registered protocol family 10
[ 2481.093288] eth0: no IPv6 routers present
[ 2998.188909] ieee80211 phy0: wl_ops_config: change monitor mode: false (implement)
[ 2998.188916] ieee80211 phy0: wl_ops_config: change power-save mode: false (implement)
[ 2998.190426] ieee80211 phy0: wl_ops_bss_info_changed: qos enabled: false (implement)
[ 2998.190818] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2999.216057] wlan0: direct probe to 00:18:e7:d1:6c:28 (try 1/3)
[ 2999.414036] wlan0: direct probe to 00:18:e7:d1:6c:28 (try 2/3)
[ 2999.613915] wlan0: direct probe to 00:18:e7:d1:6c:28 (try 3/3)
[ 2999.813798] wlan0: direct probe to 00:18:e7:d1:6c:28 timed outEDIT: For what it's worth, I ran dmesg again after having tried ctrl+c in the wpa_supplicant terminal, and it gave the same output.
Last edited by Revestek (2011-10-23 00:03:52)
Offline
#6 2011-10-23 00:09:24
- Gusar
- Member
- Registered: 2009-08-25
- Posts: 3,605
Re: [SOLVED] wpa_supplicant causes system to crash
Ok, those messages I've seen before. Haven't seen a solution though, so don't know how to help further. Except maybe this: Use a 3.1 kernel (3.1-rc10 is the latest), and blacklist brcmsmac. The 3.1 kernel has support for this card in the bcma+b43 drivers. If you go that route, you also need firmware, the b43-firmware package from AUR will install the correct version.
Offline
#7 2011-10-23 01:29:01
- Revestek
- Member
- Registered: 2011-10-22
- Posts: 5
Re: [SOLVED] wpa_supplicant causes system to crash
Ok, I will try that tomorrow then. Thanks again for helping 
Offline
#8 2011-10-23 18:01:24
- Revestek
- Member
- Registered: 2011-10-22
- Posts: 5
Re: [SOLVED] wpa_supplicant causes system to crash
Hooray it worked 
I updated to the 3.1 kernel, installed b43-firmware and blacklisted brcmsmac, and now wpa_supplicant works without a hitch.
Offline