You are not logged in.

#1 2012-05-31 13:47:56

rdm
Member
From: Italy
Registered: 2012-05-31
Posts: 48

Increase screen resolution

Hello.

I've got a Packard Bell netbook, and because of some application, I'd need to increase my screen resolution, which is currently 1024x600, to values such as 1024x768. I don't know whether it's possible, neither if it depends only on hardware, even though I've heard something about some softwares like newrez (but it seems to be a Nautilus script, while I use KDE).

Thus, anyone could suggest me on how to proceed?

Offline

#2 2012-05-31 14:09:28

Trilby
Inspector Parrot
Registered: 2011-11-29
Posts: 30,557
Website

Re: Increase screen resolution

Have you checked xrandr?  If that resolution is an option there, then just select it with xrandr.  If it's not an option in xrandr, then you'd need a different video driver - and this is assuming your hardware even supports that resolution.

Useful information to proceed would be the output of `xrandr` and `lspci | grep -i vga` as well as what video driver you are currently using (ie `pacman -Qs xf86-video`)


"UNIX is simple and coherent" - Dennis Ritchie; "GNU's Not Unix" - Richard Stallman

Offline

#3 2012-05-31 14:17:09

vacant
Member
From: downstairs
Registered: 2004-11-05
Posts: 816

Re: Increase screen resolution

You can probably have a desktop bigger than your physical screen size - it just scrolls when the pointer hits an edge.

Offline

#4 2012-05-31 15:05:06

rdm
Member
From: Italy
Registered: 2012-05-31
Posts: 48

Re: Increase screen resolution

Yes, xrandr says that the maximum resolution is 4096x4096, but when I tried to create and add a new mode, then it printed some errors.
Here's some steps:

[riccardo@server1 ~]$ xrandr
Screen 0: minimum 320 x 200, current 1024 x 600, maximum 4096 x 4096
LVDS1 connected 1024x600+0+0 (normal left inverted right x axis y axis) 222mm x 125mm
   1024x600       60.0*+
   800x600        60.3     56.2  
   640x480        59.9  
VGA1 disconnected (normal left inverted right x axis y axis)

[riccardo@server1 ~]$ cvt 1024 768
# 1024x768 59.92 Hz (CVT 0.79M3) hsync: 47.82 kHz; pclk: 63.50 MHz
Modeline "1024x768_60.00"   63.50  1024 1072 1176 1328  768 771 775 798 -hsync +vsync

[riccardo@server1 ~]$ xrandr --newmode "1024x768_60.00"   63.50  1024 1072 1176 1328  768 771 775 798 -hsync +vsync

[riccardo@server1 ~]$ xrandr --addmode LVDS1 1024x768_60.00
X Error of failed request:  BadMatch (invalid parameter attributes)
  Major opcode of failed request:  149 (RANDR)
  Minor opcode of failed request:  18 (RRAddOutputMode)
  Serial number of failed request:  25
  Current serial number in output stream:  26

[riccardo@server1 ~]$ xrandr --output LVDS1 --mode 1024x768_60.00
xrandr: cannot find mode 1024x768_60.00

At this point I started getting confused, so I typed again

[riccardo@server1 ~]$ xrandr
Screen 0: minimum 320 x 200, current 1024 x 600, maximum 4096 x 4096
LVDS1 connected 1024x600+0+0 (normal left inverted right x axis y axis) 222mm x 125mm
   1024x600       60.0*+
   800x600        60.3     56.2  
   640x480        59.9  
VGA1 disconnected (normal left inverted right x axis y axis)
  1024x768_60.00 (0x173)   63.5MHz
        h: width  1024 start 1072 end 1176 total 1328 skew    0 clock   47.8KHz
        v: height  768 start  771 end  775 total  798           clock   59.9Hz

What does that mean? Did I do anything wrong?

Other useful information:

[riccardo@server1 ~]$ lspci  
00:00.0 Host bridge: Intel Corporation N10 Family DMI Bridge (rev 02)
00:02.0 VGA compatible controller: Intel Corporation N10 Family Integrated Graphics Controller (rev 02)
00:02.1 Display controller: Intel Corporation N10 Family Integrated Graphics Controller (rev 02)
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02)
00:1d.0 USB controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02)
00:1d.1 USB controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02)
00:1d.2 USB controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02)
00:1d.3 USB controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02)
00:1d.7 USB controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation NM10 Family LPC Controller (rev 02)
00:1f.2 IDE interface: Intel Corporation N10/ICH7 Family SATA Controller [IDE mode] (rev 02)
00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02)
01:00.0 Ethernet controller: Atheros Communications Inc. AR8152 v1.1 Fast Ethernet (rev c1)
02:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)

[riccardo@server1 ~]$ pacman -Qs xf86-video
local/xf86-video-fbdev 0.4.2-5 (xorg-drivers xorg)
    X.org framebuffer video driver
local/xf86-video-intel 2.17.0-2 (xorg-drivers xorg)
    X.org Intel i810/i830/i915/945G/G965+ video drivers
local/xf86-video-vesa 2.3.0-7 (xorg-drivers xorg)
    X.org vesa video driver

Offline

Board footer

Powered by FluxBB