You are not logged in.
I upgraded both the ati driver and xorg yesterday, restarted x, and my triple monitor setup, using 2 ATI cards no longer worked. In my prior setup, I used a 10-monitor.conf with xinerama disabled, then when xserver started, I'd run a script to start i3 on my second card with a DISPLAY= command, and my other monitor with xrandr [messy, but it always worked for my needs]
That broke, and I could no longer navigate onto my secondary card [which is the onboard one] I could see it, it just wouldn't let me even navigate a mouse pointer there.
I enabled xinerama, and I have it essentially working [with no need for the scripts I previously used], but now my card that has 2 screens off the one card is playing up. Left screen = fine, middle screen = starts as clone of left screen, if I scroll right, it enters the actual middle monitor area, then if I keep scrolling it goes into monitor 3 [the right most one]
Then if I scroll back to monitor on the far left, I can no longer see what is on the middle screen, which isn't great from a productivity POV.
/etc/X11/xorg.d/10-monitor.conf :
Section "Monitor"
Identifier "Monitor0"
EndSection
Section "Monitor"
Identifier "Monitor1"
EndSection
Section "Monitor"
Identifier "Monitor2"
EndSection
Section "Device"
Identifier "Device1"
Driver "radeon"
# Option "ZaphodHeads" "VGA-1"
BusID "PCI:1:05:0"
EndSection
Section "Device"
Identifier "Device2"
Driver "radeon"
# Option "ZophodHeads" "DVI-0"
# Option "ZaphodHaeds" "VGA-0"
BusID "PCI:2:0:0"
EndSection
Section "Device"
Identifier "Device3"
Driver "radeon"
# Option "ZophodHeads" "VGA-0"
BusID "PCI:2.0.0"
EndSection
Section "Screen"
Identifier "Screen2" #Collapse Monitor and Device section to Screen section
Device "Device1"
Monitor "Monitor1"
DefaultDepth 16 #Choose the depth (16||24)
SubSection "Display"
Depth 16
Modes "1280x1024_60.00" #Choose the resolution
# Modes "1024x768_60.00" #Choose the resolution
EndSubSection
EndSection
Section "Screen"
Identifier "Screen1" #Collapse Monitor and Device section to Screen section
Device "Device2"
Monitor "Monitor0"
DefaultDepth 16 #Choose the depth (16||24)
SubSection "Display"
Depth 16
# Modes "1024x768_60.00" #Choose the resolution
Virtual 2560 1048
Modes "1280x1024_60.00" #Choose the resolution
EndSubSection
EndSection
Section "Screen"
Identifier "Screen3"
Device "Device2"
Monitor "Monitor2"
DefaultDepth 16
SubSection "Display"
Depth 16
Virtual 2560 1048
Modes "1280x1024_60.00"
EndSubSection
EndSection
Section "ServerLayout"
Identifier "TripleSreen"
Screen 0 "Screen1" 0 0
Screen 1 "Screen2" RightOf "Screen1"
Screen 2 "Screen3" RightOf "screen2"
Option "Clone" "off"
Option "Composite" "off"
Option "Xinerama" "on" #To move windows between screens
# Option "Xinerama" "0"
EndSectionagain, it is a bit of a mess, but it has just been added to gradually with changes
Any help much appreciated.
Last edited by hume's doona (2012-10-16 08:56:34)
Offline
I think you need to remove the numbers on the Screen lines inside ServerLayout. I believe those are only needed in non-Xinerama setup. I currently have a triple head with two radeon cards, one onboard and one discrete working with linux 3.6.2 and xorg 1.13. Here is my xorg.conf file. Also, it was a while ago but I recall using "RightOf" had some problem and when I used "LeftOf" it worked better, it is something you can try.
Section "ServerLayout"
Identifier "multihead"
Screen "onboard-vga"
Screen "r6670" LeftOf "onboard-vga"
Screen "onboard-dvi" LeftOf "r6670"
Option "Xinerama" "on"
EndSection
Section "Monitor"
Identifier "etronix"
EndSection
Section "Monitor"
Identifier "dell"
EndSection
Section "Monitor"
Identifier "hannsg"
EndSection
Section "Device"
Identifier "r6670"
Driver "radeon"
BusID "PCI:2:0:0"
EndSection
Section "Device"
Identifier "onboard-vga"
Driver "radeon"
BusID "PCI:1:5:0"
EndSection
Section "Device"
Identifier "onboard-dvi"
Driver "radeon"
BusID "PCI:1:5:0"
Screen 1
EndSection
Section "Screen"
Identifier "r6670"
Device "r6670"
Monitor "hannsg"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Section "Screen"
Identifier "onboard-dvi"
Device "onboard-dvi"
Monitor "etronix"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Section "Screen"
Identifier "onboard-vga"
Device "onboard-vga"
Monitor "dell"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSectionLast edited by wuzzeb (2012-10-15 22:33:16)
Offline
Thank you, oddly enough: "LeftOf" fixed it
Offline