You are not logged in.

#1 2012-10-15 10:08:47

hume's doona
Member
Registered: 2009-12-11
Posts: 206

[SOLVED]ATI - Xorg update broke triple monitor-two card setup

I upgraded both the ati driver and xorg yesterday, restarted x, and my triple monitor setup, using 2 ATI cards no longer worked. In my prior setup, I used a 10-monitor.conf with xinerama disabled, then when xserver started, I'd run a script to start i3 on my second card with a DISPLAY= command, and my other monitor with xrandr [messy, but it always worked for my needs]

That broke, and I could no longer navigate onto my secondary card [which is the onboard one] I could see it, it just wouldn't let me even navigate a mouse pointer there.

I enabled xinerama, and I have it essentially working [with no need for the scripts I previously used], but now my card that has 2 screens off the one card is playing up. Left screen = fine, middle screen = starts as clone of left screen, if I scroll right, it enters the actual middle monitor area, then if I keep scrolling it goes into monitor 3 [the right most one]

Then if I scroll back to monitor on the far left, I can no longer see what is on the middle screen, which isn't great from a productivity POV.

/etc/X11/xorg.d/10-monitor.conf :

Section "Monitor"
    Identifier             "Monitor0"
EndSection
Section "Monitor"
    Identifier             "Monitor1"
EndSection
Section "Monitor"
    Identifier		   "Monitor2"
EndSection
Section "Device"
    Identifier             "Device1"
    Driver                 "radeon"
#    Option	           "ZaphodHeads" "VGA-1"
    BusID                  "PCI:1:05:0"
EndSection
Section "Device"
    Identifier             "Device2"
    Driver                 "radeon"
#    Option		   "ZophodHeads" "DVI-0"
#    Option		   "ZaphodHaeds" "VGA-0"
    BusID                  "PCI:2:0:0"
EndSection
Section "Device"
    Identifier             "Device3"
    Driver                 "radeon"
#    Option		   "ZophodHeads" "VGA-0"
    BusID		   "PCI:2.0.0"
EndSection
Section "Screen"
    Identifier             "Screen2"  #Collapse Monitor and Device section to Screen section
    Device                 "Device1"
    Monitor                "Monitor1"
    DefaultDepth            16 #Choose the depth (16||24)
    SubSection             "Display"
        Depth               16
        Modes              "1280x1024_60.00" #Choose the resolution
#        Modes              "1024x768_60.00" #Choose the resolution
    EndSubSection
EndSection
Section "Screen"
    Identifier             "Screen1"  #Collapse Monitor and Device section to Screen section
    Device                 "Device2"
    Monitor                "Monitor0"
    DefaultDepth            16 #Choose the depth (16||24)
    SubSection             "Display"
        Depth               16
#        Modes              "1024x768_60.00" #Choose the resolution
	Virtual		   2560 1048
        Modes              "1280x1024_60.00" #Choose the resolution
    EndSubSection
EndSection
Section "Screen"
    Identifier		   "Screen3"
    Device		   "Device2"
    Monitor		   "Monitor2"
    DefaultDepth	    16
    SubSection		   "Display"
	    Depth	    16
	    Virtual	    2560 1048
	    Modes	   "1280x1024_60.00"
    EndSubSection
EndSection
Section "ServerLayout"
    Identifier     "TripleSreen"
    Screen      0 "Screen1" 0 0 
    Screen	1 "Screen2" RightOf "Screen1"
    Screen	2 "Screen3" RightOf "screen2"
    Option	   "Clone" "off"
    Option         "Composite" "off"
    Option         "Xinerama" "on" #To move windows between screens
#    Option         "Xinerama" "0"
EndSection

again, it is a bit of a mess, but it has just been added to gradually with changes

Any help much appreciated.

Last edited by hume's doona (2012-10-16 08:56:34)

Offline

#2 2012-10-15 22:31:03

wuzzeb
Member
Registered: 2012-10-15
Posts: 6

Re: [SOLVED]ATI - Xorg update broke triple monitor-two card setup

I think you need to remove the numbers on the Screen lines inside ServerLayout.  I believe those are only needed in non-Xinerama setup.  I currently have a triple head with two radeon cards, one onboard and one discrete working with linux 3.6.2 and xorg 1.13.  Here is my xorg.conf file.  Also, it was a while ago but I recall using "RightOf" had some problem and when I used "LeftOf" it worked better, it is something you can try.

Section "ServerLayout"
	Identifier     "multihead"
	Screen         "onboard-vga"
	Screen         "r6670" LeftOf "onboard-vga"
	Screen         "onboard-dvi" LeftOf "r6670"
	Option         "Xinerama" "on"
EndSection

Section "Monitor"
	Identifier   "etronix"
EndSection

Section "Monitor"
	Identifier   "dell"
EndSection

Section "Monitor"
	Identifier   "hannsg"
EndSection

Section "Device"
	Identifier  "r6670"
	Driver      "radeon"
	BusID       "PCI:2:0:0"
EndSection

Section "Device"
	Identifier  "onboard-vga"
	Driver      "radeon"
	BusID       "PCI:1:5:0"
EndSection

Section "Device"
	Identifier  "onboard-dvi"
	Driver      "radeon"
	BusID       "PCI:1:5:0"
	Screen      1
EndSection

Section "Screen"
	Identifier "r6670"
	Device     "r6670"
	Monitor    "hannsg"
	DefaultDepth     24
	SubSection "Display"
		Viewport   0 0
		Depth     24
	EndSubSection
EndSection

Section "Screen"
	Identifier "onboard-dvi"
	Device     "onboard-dvi"
	Monitor    "etronix"
	DefaultDepth     24
	SubSection "Display"
		Viewport   0 0
		Depth     24
	EndSubSection
EndSection

Section "Screen"
	Identifier "onboard-vga"
	Device     "onboard-vga"
	Monitor    "dell"
	DefaultDepth     24
	SubSection "Display"
		Viewport   0 0
		Depth     24
	EndSubSection
EndSection

Last edited by wuzzeb (2012-10-15 22:33:16)

Offline

#3 2012-10-16 08:56:08

hume's doona
Member
Registered: 2009-12-11
Posts: 206

Re: [SOLVED]ATI - Xorg update broke triple monitor-two card setup

Thank you, oddly enough: "LeftOf" fixed it

Offline

Board footer

Powered by FluxBB