You are not logged in.
Pages: 1
I have got this problem since i bought this Ethernet adapter. I mainly boght it, because I wanted to run OpenBSD. But it just doesn't work. Theres i light when I plug my ethernet cable to it, but that it just about it.
I have tried to disable my onboard ethernet controller (VIA Technologies Inc|VT3119 Gigabit Ethernet Controller), and add "pci=routeirq". But that hasn't worked at all.
From 'lspci -vv
01:07.0 Ethernet controller: VIA Technologies, Inc. VT6105 [Rhine-III] (rev 86)
Subsystem: D-Link System Inc: Unknown device 1403
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at a000 [size=256]
Region 1: Memory at eb013000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: <available only to root>And from 'dmesg'
Linux version 2.6.12-ARCH (root@earth) (gcc version 3.4.3) #1 SMP Fri Jul 1 11:55:48 PDT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
On node 0 totalpages: 262128
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 32752 pages, LIFO batch:15
DMI 2.2 present.
ACPI: RSDP (v000 Nvidia ) @ 0x000f7a20
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff3000
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff3040
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff8300
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:10 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 40000000:bec00000)
Built 1 zonelists
Kernel command line: root=/dev/discs/disc0/part1 devfs=nomount pci=routeirq vga=792 ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2166.913 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1032576k/1048512k available (4079k kernel code, 15160k reserved, 1270k data, 288k init, 131008k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 4292.60 BogoMIPS (lpj=2146304)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: AMD Athlon(tm) XP 3000+ stepping 00
Total of 1 processors activated (4292.60 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=0 pin2=-1
Brought up 1 CPUs
CPU0 attaching sched-domain:
domain 0: span 1
groups: 1
domain 1: span 1
groups: 1
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfbb70, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:02:00.0
ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.HUB0._PRT]
ACPI: Power Resource [ISAV] (on)
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs *1, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 22) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: Routing PCI interrupts for all devices because "pci=routeirq" specified
ACPI: PCI Interrupt Link [APCS] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:01.1[A] -> Link [APCS] -> GSI 23 (level, low) -> IRQ 23
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 21 (level, high) -> IRQ 21
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 20 (level, high) -> IRQ 20
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 21 (level, high) -> IRQ 21
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [APSI] -> GSI 22 (level, high) -> IRQ 22
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 19
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18
ACPI: PCI Interrupt 0000:01:0a.1[B] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 19
ACPI: PCI Interrupt 0000:01:0a.2[C] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 19
pnp: 00:00: ioport range 0x4000-0x407f could not be reserved
pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
pnp: 00:00: ioport range 0x4400-0x447f has been reserved
pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved
pnp: 00:00: ioport range 0x4200-0x427f has been reserved
pnp: 00:00: ioport range 0x4280-0x42ff has been reserved
pnp: 00:01: ioport range 0x5000-0x503f has been reserved
pnp: 00:01: ioport range 0x5100-0x513f has been reserved
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
highmem bounce pool size: 64 pages
inotify device minor=63
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Installing knfsd (copyright (C) 1996 kir@monad.swb.de" target="_new">okir@monad.swb.de).
JFS: nTxBlock = 8070, nTxLock = 64560
SGI XFS with ACLs, security attributes, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
vesafb: framebuffer at 0xd0000000, mapped to 0xf8d00000, using 6144k, total 262144k
vesafb: mode is 1024x768x32, linelength=4096, pages=1
vesafb: protected mode interface info at c000:d4d0
vesafb: scrolling: redraw
vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (45 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected NVIDIA nForce2 chipset
agpgart: AGP aperture is 128M @ 0xe0000000
intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/915G chipsets
intelfb: Version 0.9.2
PNP: PS/2 Controller [PNP0303S2K,PNP0f13S2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2-U400R: IDE controller at PCI slot 0000:00:09.0
NFORCE2-U400R: chipset revision 163
NFORCE2-U400R: not 100% native mode: will probe irqs later
NFORCE2-U400R: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2-U400R: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2-U400R: 0000:00:09.0 (rev a3) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hdaMA, hdbMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdcMA, hddMA
Probing IDE interface ide0...
hda: SAMSUNG SP1203N, ATA DISK drive
hdb: Maxtor 6Y080P0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: LITE-ON LTR-52327S, ATAPI CD/DVD-ROM drive
hdd: DVD-ROM BDV316E, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 1024KiB
hda: 234493056 sectors (120060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
hdb: max request size: 128KiB
hdb: 160086528 sectors (81964 MB) w/7936KiB Cache, CHS=65535/16/63, UDMA(133)
hdb: cache flushes supported
/dev/ide/host0/bus0/target1/lun0: p1 p2
hdc: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 40X DVD-ROM drive, 512kB Cache
libata version 1.11 loaded.
sata_nv version 0.6
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [APSI] -> GSI 22 (level, high) -> IRQ 22
PCI: Setting latency timer of device 0000:00:0b.0 to 64
ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xE000 irq 22
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xE008 irq 22
ata1: no device found (phy stat 00000000)
scsi0 : sata_nv
ata2: no device found (phy stat 00000000)
scsi1 : sata_nv
mice: PS/2 mouse device common for all mice
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid10 personality registered as nr 9
md: raid5 personality registered as nr 4
raid5: automatically using best checksumming function: pIII_sse
pIII_sse : 5844.000 MB/sec
raid5: using function: pIII_sse (5844.000 MB/sec)
raid6: int32x1 894 MB/s
raid6: int32x2 1093 MB/s
raid6: int32x4 710 MB/s
raid6: int32x8 687 MB/s
raid6: mmxx1 1808 MB/s
raid6: mmxx2 3082 MB/s
raid6: sse1x1 1730 MB/s
raid6: sse1x2 2816 MB/s
raid6: using algorithm sse1x2 (2816 MB/s)
md: raid6 personality registered as nr 8
md: multipath personality registered as nr 7
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 64Kbytes
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 10
Disabled Privacy Extensions on device c05dbde0(lo)
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
ACPI wakeup devices:
HUB0 HUB1 USB0 USB1 USB2 F139 MMAC MMCI UAR1
ACPI: (supports S0 S1 S4 S5)
devfs_mk_dev: could not append to parent for md/0
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
ReiserFS: hda1: found reiserfs format "3.6" with standard journal
input: AT Translated Set 2 keyboard on isa0060/serio0
input: PS2++ Logitech MX Mouse on isa0060/serio1
ReiserFS: hda1: using ordered data mode
ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda1: checking transaction log (hda1)
ReiserFS: hda1: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 288k freed
cdrom: open failed.
cdrom: open failed.
Adding 128512k swap on /dev/discs/disc0/part2. Priority:-1 extents:1
ReiserFS: hda3: found reiserfs format "3.6" with standard journal
ReiserFS: hda3: using ordered data mode
ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda3: checking transaction log (hda3)
ReiserFS: hda3: Using r5 hash to sort names
usbcore: registered new driver usbfs
usbcore: registered new driver hub
VIA Networking Velocity Family Gigabit Ethernet Adapter Driver Ver. 1.13
Copyright (c) 2002, 2003 VIA Networking Technologies, Inc.
Copyright (c) 2004 Red Hat Inc.
ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18
PCI: Via IRQ fixup for 0000:01:0b.0, from 10 to 2
eth0: VIA Networking Velocity Family Gigabit Ethernet Adapter
eth0: Ethernet Address: 00:50:8D:62:92:E4
Velocity is AUTO mode
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16
Audigy2 value:Special config.
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
kqemu: module license 'unspecified' taints kernel.
QEMU Accelerator Module version 1.1.0, Copyright (c) 2005 Fabrice Bellard
This is a proprietary product. Read the LICENSE file for more information
Redistribution of this module is prohibited without authorization
KQEMU installed, max_instances=4 max_locked_mem=129156kB.
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 19
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7667 Fri Jun 17 07:01:04 PDT 2005
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x5000
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5100
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 19
PCI: Via IRQ fixup for 0000:01:07.0, from 5 to 3
eth1: VIA Rhine III at 0x1a000, 00:11:95:d8:3b:a6, IRQ 19.
eth1: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18
PCI: Via IRQ fixup for 0000:01:0a.0, from 10 to 2
uhci_hcd 0000:01:0a.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:01:0a.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:01:0a.0: irq 18, io base 0x0000a800
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:01:0a.1[B] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 19
PCI: Via IRQ fixup for 0000:01:0a.1, from 5 to 3
uhci_hcd 0000:01:0a.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:01:0a.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:01:0a.1: irq 19, io base 0x0000ac00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 21 (level, high) -> IRQ 21
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: nVidia Corporation MCP2A USB Controller
ehci_hcd 0000:00:02.2: debug port 1
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:02.2: irq 21, io mem 0xec004000
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:01:0a.2[C] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16
PCI: Via IRQ fixup for 0000:01:0a.2, from 3 to 0
ehci_hcd 0000:01:0a.2: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:01:0a.2: new USB bus registered, assigned bus number 4
ehci_hcd 0000:01:0a.2: irq 16, io mem 0xeb011000
ehci_hcd 0000:01:0a.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 4 ports detected
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 21 (level, high) -> IRQ 21
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: nVidia Corporation MCP2A USB Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:02.0: irq 21, io mem 0xec002000
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 20 (level, high) -> IRQ 20
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: nVidia Corporation MCP2A USB Controller (#2)
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 6
ohci_hcd 0000:00:02.1: irq 20, io mem 0xec003000
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 4 ports detected
eth0: no IPv6 routers present
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:02:00.0 into 8x mode
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:02:00.0 into 8x mode
Velocity is AUTO mode
eth0: Link autonegation speed 100M bps full duplex
eth0: no IPv6 routers presentCould anyone tell me the problem? I am not strong in this kind of hardware.
Arch - It's something refreshing
Offline
Pages: 1