You are not logged in.
I have an...
Acer C710-844G01ii
I have replaced the original SSD with a Mushkin 120GB SSD (MKNSSDCR120GB-7)
I've used John Lewis' script at https://johnlewis.ie to flash the firmware. It works great. It loads 64 bit dual arch iso (2014.10.01) written to a USB flashdrive (Well, I'm actually using SD card in a USB reader. Not sure if that makes a difference) without having to utilize the workaround listed on the Chromebook wiki page (https://wiki.archlinux.org/index.php/Ch … stallation). I just create a regular arch bootable usb and it seems to work fine. I can use the bootable USB tools. I can install arch to the hard disk fine. (I did this a couple of times on the original SSD that came with the chromebook before I replaced it, so I know it works without having to change the SSD).
The problem I'm having occurs after I install the patched kernel (linux-chromebook-3.16.4-1-x86_64 or linux-mainline-chromebook-3.17-1-x86_64 I've tried them both. Both times I wiped the hard drive and went through the entire install process from scratch). After booting, everything loads up fine except that I lose functionality of my USB ports. The custom BIOS still reads the arch bootable USB if I choose to boot into it. If I boot from the hard drive though, as soon as the patched kernel loads, the USB ports are not working.
The output of
dmesg | tailis the same before and after inserting a flash drive into a usb port.
Running the command
lsusbgives output
unable to initialize libusb: -99
Offline
Rhythagoras, do your USB ports work with the standard Arch kernels? Linux-chromebook and linux-mainline chromebook don't contain any patches specific to the C710 and the only changes they make regarding USB is disabling the EHCI modules since they can lead to kernel panics during suspend/resume on Haswell Chromebooks. Again, try the standard Arch kernels first and see if those work. Otherwise it could indicate some sort of hardware issue.
Last edited by SolarBoyMatt (2014-10-13 14:15:11)
Offline
Thank you for info on the custom kernels I mentioned.
Yes, the USB ports work with the standard Arch kernel. I have it set up on my chromebook at the moment with the standard Arch kernel. Using LXDE for a desktop environment. Everything works fine there. I can mount USB flash drives. My wireless USB mouse works.
I do have one concern with the standard Arch kernel though.
Sometimes, upon booting, it hangs on this message after fsck.
Well, I see the message as the machine is booting up every time, but sometimes the system stalls and will not accept input from the keyboard.
[ 1.23117] usb 1-1.1: string descriptor 0 read error: -22 Offline
Yes, the USB ports work with the standard Arch kernel.
...
Well, I see the message as the machine is booting up every time, but sometimes the system stalls and will not accept input from the keyboard.[ 1.23117] usb 1-1.1: string descriptor 0 read error: -22
Is it working now? If not, will you please post the output of 'dmesg' and 'lsusb', with the standard kernel?
Last edited by scot14 (2014-10-26 18:17:09)
Offline
Updated the system, now using arch kernel 3.17.1-1
Problem still exists.
dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.17.1-1-ARCH (nobody@var-lib-archbuild-testing-x86_64-tobias) (gcc version 4.9.1 20140903 (prerelease) (GCC) ) #1 SMP PREEMPT Wed Oct 15 15:04:35 CEST 2014
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=572dffe4-4501-4df5-967f-c535313cfa24 rw quiet
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000020200000-0x000000003fffffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000040000000-0x00000000401fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000040200000-0x00000000acee3fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000acee4000-0x00000000af9fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f0000000-0x00000000f3ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000014f5fffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: Google Parrot/Parrot, BIOS 4.0-6588-g4acd8ea-dirty 09/04/2014
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] e820: last_pfn = 0x14f600 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: write-back
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-back
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0AD000000 mask FFF000000 uncachable
[ 0.000000] 1 base 0AE000000 mask FFE000000 uncachable
[ 0.000000] 2 base 0B0000000 mask FF0000000 uncachable
[ 0.000000] 3 base 0C0000000 mask FF0000000 uncachable
[ 0.000000] 4 base 0D0000000 mask FF0000000 write-combining
[ 0.000000] 5 base 0E0000000 mask FE0000000 uncachable
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820: last_pfn = 0xacee4 max_arch_pfn = 0x400000000
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
[ 0.000000] reserving inaccessible SNB gfx pages
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x01b2f000, 0x01b2ffff] PGTABLE
[ 0.000000] BRK [0x01b30000, 0x01b30fff] PGTABLE
[ 0.000000] BRK [0x01b31000, 0x01b31fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x14f400000-0x14f5fffff]
[ 0.000000] [mem 0x14f400000-0x14f5fffff] page 2M
[ 0.000000] BRK [0x01b32000, 0x01b32fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x14c000000-0x14f3fffff]
[ 0.000000] [mem 0x14c000000-0x14f3fffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x14bffffff]
[ 0.000000] [mem 0x100000000-0x14bffffff] page 2M
[ 0.000000] BRK [0x01b33000, 0x01b33fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x1fffffff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x1fffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x20200000-0x3fffffff]
[ 0.000000] [mem 0x20200000-0x3fffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x40200000-0xacee3fff]
[ 0.000000] [mem 0x40200000-0xacdfffff] page 2M
[ 0.000000] [mem 0xace00000-0xacee3fff] page 4k
[ 0.000000] BRK [0x01b34000, 0x01b34fff] PGTABLE
[ 0.000000] RAMDISK: [mem 0x379a0000-0x37cc7fff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F6DD0 000024 (v02 CORE )
[ 0.000000] ACPI: XSDT 0x00000000ACFEF0E0 00004C (v01 CORE COREBOOT 00000000 CORE 00000000)
[ 0.000000] ACPI: FACP 0x00000000ACFF2720 0000F4 (v03 CORE COREBOOT 00000000 CORE 00000001)
[ 0.000000] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 128/64 (20140724/tbfadt-618)
[ 0.000000] ACPI: DSDT 0x00000000ACFEF250 0034C7 (v02 COREv4 COREBOOT 20110725 INTL 20140114)
[ 0.000000] ACPI: FACS 0x00000000ACFEF210 000040
[ 0.000000] ACPI: HPET 0x00000000ACFF2820 000038 (v01 CORE COREBOOT 00000000 CORE 00000000)
[ 0.000000] ACPI: APIC 0x00000000ACFF2860 00005C (v01 CORE COREBOOT 00000000 CORE 00000000)
[ 0.000000] ACPI: MCFG 0x00000000ACFF28C0 00003C (v01 CORE COREBOOT 00000000 CORE 00000000)
[ 0.000000] ACPI: SSDT 0x00000000ACFF3900 000818 (v02 CORE COREBOOT 0000002A CORE 0000002A)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000014f5fffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x14f5fffff]
[ 0.000000] NODE_DATA [mem 0x14f5fa000-0x14f5fdfff]
[ 0.000000] [ffffea0000000000-ffffea00053fffff] PMD -> [ffff88014ac00000-ffff88014ebfffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x14f5fffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0009efff]
[ 0.000000] node 0: [mem 0x00100000-0x1fffffff]
[ 0.000000] node 0: [mem 0x20200000-0x3fffffff]
[ 0.000000] node 0: [mem 0x40200000-0xacee3fff]
[ 0.000000] node 0: [mem 0x100000000-0x14f5fffff]
[ 0.000000] On node 0 totalpages: 1032322
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 158 pages reserved
[ 0.000000] DMA zone: 3998 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 10988 pages used for memmap
[ 0.000000] DMA32 zone: 703204 pages, LIFO batch:31
[ 0.000000] Normal zone: 5080 pages used for memmap
[ 0.000000] Normal zone: 325120 pages, LIFO batch:31
[ 0.000000] Reserving Intel graphics stolen memory at 0xada00000-0xaf9fffff
[ 0.000000] ACPI: PM-Timer IO Port: 0x508
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x02] enabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x20000000-0x201fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x40000000-0x401fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xacee4000-0xaf9fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xafa00000-0xefffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xf3ffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf4000000-0xffffffff]
[ 0.000000] e820: [mem 0xafa00000-0xefffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88014f200000 s86848 r8192 d23744 u1048576
[ 0.000000] pcpu-alloc: s86848 r8192 d23744 u1048576 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1016032
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=572dffe4-4501-4df5-967f-c535313cfa24 rw quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave: enabled xstate_bv 0x3, cntxt size 0x240 using standard form
[ 0.000000] AGP: Checking aperture...
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 3981852K/4129288K available (5381K kernel code, 909K rwdata, 1712K rodata, 1140K init, 1176K bss, 147436K reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:8448 nr_irqs:440 0
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 16777216 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 1097.469 MHz processor
[ 0.000073] Calibrating delay loop (skipped), value calculated using timer frequency.. 2195.39 BogoMIPS (lpj=3658230)
[ 0.000078] pid_max: default: 32768 minimum: 301
[ 0.000089] ACPI: Core revision 20140724
[ 0.005690] ACPI: All ACPI Tables successfully acquired
[ 0.008808] Security Framework initialized
[ 0.008819] Yama: becoming mindful.
[ 0.009391] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.011193] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.012001] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.012017] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.012360] Initializing cgroup subsys memory
[ 0.012370] Initializing cgroup subsys devices
[ 0.012374] Initializing cgroup subsys freezer
[ 0.012378] Initializing cgroup subsys net_cls
[ 0.012382] Initializing cgroup subsys blkio
[ 0.012420] CPU: Physical Processor ID: 0
[ 0.012422] CPU: Processor Core ID: 0
[ 0.012432] mce: CPU supports 7 MCE banks
[ 0.012454] CPU0: Thermal monitoring enabled (TM1)
[ 0.012472] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 8
Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32, 1GB 0
[ 0.012675] Freeing SMP alternatives memory: 20K (ffffffff81a02000 - ffffffff81a07000)
[ 0.014781] ftrace: allocating 20674 entries in 81 pages
[ 0.037109] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.070117] smpboot: CPU0: Intel(R) Celeron(R) CPU 847 @ 1.10GHz (fam: 06, model: 2a, stepping: 07)
[ 0.070132] TSC deadline timer enabled
[ 0.070178] Performance Events: PEBS fmt1+, 16-deep LBR, SandyBridge events, full-width counters, Intel PMU driver.
[ 0.070223] ... version: 3
[ 0.070226] ... bit width: 48
[ 0.070228] ... generic registers: 8
[ 0.070230] ... value mask: 0000ffffffffffff
[ 0.070232] ... max period: 0000ffffffffffff
[ 0.070234] ... fixed-purpose events: 3
[ 0.070237] ... event mask: 00000007000000ff
[ 0.090307] x86: Booting SMP configuration:
[ 0.090312] .... node #0, CPUs: #1
[ 0.103535] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.103559] x86: Booted up 1 node, 2 CPUs
[ 0.103563] smpboot: Total of 2 processors activated (4391.78 BogoMIPS)
[ 0.105926] devtmpfs: initialized
[ 0.112736] pinctrl core: initialized pinctrl subsystem
[ 0.112812] RTC time: 0:25:43, date: 10/27/14
[ 0.112986] NET: Registered protocol family 16
[ 0.113224] cpuidle: using governor ladder
[ 0.113230] cpuidle: using governor menu
[ 0.113291] ACPI: bus type PCI registered
[ 0.113295] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.113438] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000)
[ 0.113443] PCI: MMCONFIG at [mem 0xf0000000-0xf3ffffff] reserved in E820
[ 0.113650] PCI: Using configuration type 1 for base access
[ 0.124189] ACPI: Added _OSI(Module Device)
[ 0.124193] ACPI: Added _OSI(Processor Device)
[ 0.124196] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.124199] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.130313] ACPI: Interpreter enabled
[ 0.130327] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20140724/hwxface-580)
[ 0.130336] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140724/hwxface-580)
[ 0.130364] ACPI: (supports S0 S3 S4 S5)
[ 0.130367] ACPI: Using IOAPIC for interrupt routing
[ 0.130407] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.136949] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.136960] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.137053] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[ 0.137240] acpi PNP0A08:00: ignoring host bridge window [mem 0x000cc000-0x000cffff] (conflicts with Video ROM [mem 0x000c0000-0x000cedff])
[ 0.137249] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[ 0.137502] PCI host bridge to bus 0000:00
[ 0.137507] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.137512] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.137515] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.137519] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.137523] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000c3fff]
[ 0.137526] pci_bus 0000:00: root bus resource [mem 0x000c4000-0x000c7fff]
[ 0.137529] pci_bus 0000:00: root bus resource [mem 0x000c8000-0x000cbfff]
[ 0.137533] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff]
[ 0.137536] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff]
[ 0.137540] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff]
[ 0.137543] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff]
[ 0.137547] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff]
[ 0.137550] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff]
[ 0.137553] pci_bus 0000:00: root bus resource [mem 0x000e8000-0x000ebfff]
[ 0.137557] pci_bus 0000:00: root bus resource [mem 0x000ec000-0x000effff]
[ 0.137560] pci_bus 0000:00: root bus resource [mem 0x000f0000-0x000fffff]
[ 0.137564] pci_bus 0000:00: root bus resource [mem 0xafa00000-0xfebfffff]
[ 0.137567] pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed44fff]
[ 0.137583] pci 0000:00:00.0: [8086:0104] type 00 class 0x060000
[ 0.137752] pci 0000:00:02.0: [8086:0106] type 00 class 0x030000
[ 0.137774] pci 0000:00:02.0: reg 0x10: [mem 0xe0000000-0xe03fffff 64bit]
[ 0.137786] pci 0000:00:02.0: reg 0x18: [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.137796] pci 0000:00:02.0: reg 0x20: [io 0x1000-0x103f]
[ 0.138004] pci 0000:00:16.0: [8086:1e3a] type 00 class 0x078000
[ 0.138046] pci 0000:00:16.0: reg 0x10: [mem 0xe0706100-0xe070610f 64bit]
[ 0.138188] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.138353] pci 0000:00:1a.0: [8086:1e2d] type 00 class 0x0c0320
[ 0.138392] pci 0000:00:1a.0: reg 0x10: [mem 0xe0705800-0xe0705bff]
[ 0.138555] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.138624] pci 0000:00:1a.0: System wakeup disabled by ACPI
[ 0.138714] pci 0000:00:1b.0: [8086:1e20] type 00 class 0x040300
[ 0.138746] pci 0000:00:1b.0: reg 0x10: [mem 0xe0700000-0xe0703fff 64bit]
[ 0.138900] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.138967] pci 0000:00:1b.0: System wakeup disabled by ACPI
[ 0.139051] pci 0000:00:1c.0: [8086:1e12] type 01 class 0x060400
[ 0.139207] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.139354] pci 0000:00:1c.1: [8086:1e14] type 01 class 0x060400
[ 0.139506] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.139671] pci 0000:00:1d.0: [8086:1e26] type 00 class 0x0c0320
[ 0.139708] pci 0000:00:1d.0: reg 0x10: [mem 0xe0705c00-0xe0705fff]
[ 0.139869] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.139938] pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 0.140021] pci 0000:00:1f.0: [8086:1e5f] type 00 class 0x060100
[ 0.140331] pci 0000:00:1f.2: [8086:1e03] type 00 class 0x010601
[ 0.140373] pci 0000:00:1f.2: reg 0x10: [io 0x1060-0x1067]
[ 0.140391] pci 0000:00:1f.2: reg 0x14: [io 0x1070-0x1073]
[ 0.140409] pci 0000:00:1f.2: reg 0x18: [io 0x1068-0x106f]
[ 0.140427] pci 0000:00:1f.2: reg 0x1c: [io 0x1074-0x1077]
[ 0.140444] pci 0000:00:1f.2: reg 0x20: [io 0x1040-0x105f]
[ 0.140461] pci 0000:00:1f.2: reg 0x24: [mem 0xe0705000-0xe07057ff]
[ 0.140568] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.140707] pci 0000:00:1f.3: [8086:1e22] type 00 class 0x0c0500
[ 0.140738] pci 0000:00:1f.3: reg 0x10: [mem 0xe0706000-0xe07060ff 64bit]
[ 0.140781] pci 0000:00:1f.3: reg 0x20: [io 0x0400-0x041f]
[ 0.140941] pci 0000:00:1f.6: [8086:1e24] type 00 class 0x118000
[ 0.140981] pci 0000:00:1f.6: reg 0x10: [mem 0xe0704000-0xe0704fff 64bit]
[ 0.141361] pci 0000:01:00.0: [168c:0034] type 00 class 0x028000
[ 0.141432] pci 0000:01:00.0: reg 0x10: [mem 0xe0400000-0xe047ffff 64bit]
[ 0.141586] pci 0000:01:00.0: reg 0x30: [mem 0xe0480000-0xe048ffff pref]
[ 0.141772] pci 0000:01:00.0: supports D1 D2
[ 0.141776] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.146966] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.146982] pci 0000:00:1c.0: bridge window [mem 0xe0400000-0xe04fffff]
[ 0.147186] pci 0000:02:00.0: [14e4:16b5] type 00 class 0x020000
[ 0.147261] pci 0000:02:00.0: reg 0x10: [mem 0xe0500000-0xe050ffff 64bit pref]
[ 0.147314] pci 0000:02:00.0: reg 0x18: [mem 0xe0510000-0xe051ffff 64bit pref]
[ 0.147412] pci 0000:02:00.0: reg 0x30: [mem 0xe0600000-0xe06007ff pref]
[ 0.147646] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 0.147839] pci 0000:02:00.1: [14e4:16bc] type 00 class 0x080501
[ 0.147913] pci 0000:02:00.1: reg 0x10: [mem 0xe0520000-0xe052ffff 64bit pref]
[ 0.148270] pci 0000:02:00.1: PME# supported from D0 D3hot D3cold
[ 0.153657] pci 0000:00:1c.1: PCI bridge to [bus 02]
[ 0.153672] pci 0000:00:1c.1: bridge window [mem 0xe0600000-0xe06fffff]
[ 0.153686] pci 0000:00:1c.1: bridge window [mem 0xe0500000-0xe05fffff 64bit pref]
[ 0.153903] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11, disabled.
[ 0.153995] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10, disabled.
[ 0.154081] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11, disabled.
[ 0.154165] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15), disabled.
[ 0.154248] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11, disabled.
[ 0.154330] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[ 0.154413] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[ 0.154495] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[ 0.155375] ACPI: Enabled 1 GPEs in block 00 to 3F
[ 0.155452] ACPI : EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[ 0.155654] vgaarb: setting as boot device: PCI:0000:00:02.0
[ 0.155658] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.155664] vgaarb: loaded
[ 0.155666] vgaarb: bridge control possible 0000:00:02.0
[ 0.155751] PCI: Using ACPI for IRQ routing
[ 0.159478] PCI: pci_cache_line_size set to 64 bytes
[ 0.159577] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[ 0.159581] e820: reserve RAM buffer [mem 0xacee4000-0xafffffff]
[ 0.159584] e820: reserve RAM buffer [mem 0x14f600000-0x14fffffff]
[ 0.159796] NetLabel: Initializing
[ 0.159799] NetLabel: domain hash size = 128
[ 0.159801] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.159829] NetLabel: unlabeled traffic allowed by default
[ 0.159874] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.159885] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.161931] Switched to clocksource hpet
[ 0.171668] pnp: PnP ACPI init
[ 0.171847] system 00:00: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.171852] system 00:00: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.171857] system 00:00: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.171861] system 00:00: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.171865] system 00:00: [mem 0xf0000000-0xf3ffffff] has been reserved
[ 0.171869] system 00:00: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.171873] system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved
[ 0.171877] system 00:00: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.171881] system 00:00: [mem 0x20000000-0x201fffff] has been reserved
[ 0.171885] system 00:00: [mem 0x40000000-0x401fffff] has been reserved
[ 0.171891] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.172584] system 00:01: [mem 0xfed00000-0xfed003ff] has been reserved
[ 0.172590] system 00:01: Plug and Play ACPI device, IDs PNP0103 PNP0c01 (active)
[ 0.172671] system 00:02: [io 0x0500-0x057f] could not be reserved
[ 0.172676] system 00:02: [io 0x0480-0x04bf] has been reserved
[ 0.172681] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.172727] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.172802] pnp 00:04: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[ 0.172844] pnp: PnP ACPI: found 5 devices
[ 0.181140] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.181153] pci 0000:00:1c.0: bridge window [mem 0xe0400000-0xe04fffff]
[ 0.181169] pci 0000:00:1c.1: PCI bridge to [bus 02]
[ 0.181179] pci 0000:00:1c.1: bridge window [mem 0xe0600000-0xe06fffff]
[ 0.181187] pci 0000:00:1c.1: bridge window [mem 0xe0500000-0xe05fffff 64bit pref]
[ 0.181201] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.181205] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.181209] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.181212] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff]
[ 0.181216] pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff]
[ 0.181219] pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff]
[ 0.181223] pci_bus 0000:00: resource 10 [mem 0x000d0000-0x000d3fff]
[ 0.181226] pci_bus 0000:00: resource 11 [mem 0x000d4000-0x000d7fff]
[ 0.181230] pci_bus 0000:00: resource 12 [mem 0x000d8000-0x000dbfff]
[ 0.181233] pci_bus 0000:00: resource 13 [mem 0x000dc000-0x000dffff]
[ 0.181237] pci_bus 0000:00: resource 14 [mem 0x000e0000-0x000e3fff]
[ 0.181240] pci_bus 0000:00: resource 15 [mem 0x000e4000-0x000e7fff]
[ 0.181243] pci_bus 0000:00: resource 16 [mem 0x000e8000-0x000ebfff]
[ 0.181247] pci_bus 0000:00: resource 17 [mem 0x000ec000-0x000effff]
[ 0.181250] pci_bus 0000:00: resource 18 [mem 0x000f0000-0x000fffff]
[ 0.181254] pci_bus 0000:00: resource 19 [mem 0xafa00000-0xfebfffff]
[ 0.181257] pci_bus 0000:00: resource 20 [mem 0xfed40000-0xfed44fff]
[ 0.181262] pci_bus 0000:01: resource 1 [mem 0xe0400000-0xe04fffff]
[ 0.181266] pci_bus 0000:02: resource 1 [mem 0xe0600000-0xe06fffff]
[ 0.181269] pci_bus 0000:02: resource 2 [mem 0xe0500000-0xe05fffff 64bit pref]
[ 0.181319] NET: Registered protocol family 2
[ 0.181671] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.181835] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.181980] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.182017] TCP: reno registered
[ 0.182031] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.182066] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.182162] NET: Registered protocol family 1
[ 0.182192] pci 0000:00:02.0: Video device with shadowed ROM
[ 0.182773] PCI: CLS 64 bytes, default 64
[ 0.182860] Unpacking initramfs...
[ 0.302677] Freeing initrd memory: 3232K (ffff8800379a0000 - ffff880037cc8000)
[ 0.302693] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.302698] software IO TLB [mem 0xa8ee4000-0xacee4000] (64MB) mapped at [ffff8800a8ee4000-ffff8800acee3fff]
[ 0.302960] RAPL PMU detected, hw unit 2^-16 Joules, API unit is 2^-32 Joules, 3 fixed counters 163840 ms ovfl timer
[ 0.303038] microcode: CPU0 sig=0x206a7, pf=0x10, revision=0x28
[ 0.303051] microcode: CPU1 sig=0x206a7, pf=0x10, revision=0x28
[ 0.303148] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 0.303201] Scanning for low memory corruption every 60 seconds
[ 0.303637] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.303657] Initialise system trusted keyring
[ 0.304287] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.307213] zpool: loaded
[ 0.307219] zbud: loaded
[ 0.307572] VFS: Disk quotas dquot_6.5.2
[ 0.307644] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.307867] msgmni has been set to 7783
[ 0.307975] Key type big_key registered
[ 0.308262] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.308317] io scheduler noop registered
[ 0.308322] io scheduler deadline registered
[ 0.308380] io scheduler cfq registered (default)
[ 0.308697] pcieport 0000:00:1c.0: irq 24 for MSI/MSI-X
[ 0.308978] pcieport 0000:00:1c.1: irq 25 for MSI/MSI-X
[ 0.309161] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
[ 0.309165] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[ 0.309172] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
[ 0.309208] pcieport 0000:00:1c.1: Signaling PME through PCIe PME interrupt
[ 0.309212] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
[ 0.309215] pci 0000:02:00.1: Signaling PME through PCIe PME interrupt
[ 0.309223] pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme loaded
[ 0.309253] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.309285] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.309344] vesafb: mode is 1366x768x32, linelength=5504, pages=0
[ 0.309346] vesafb: scrolling: redraw
[ 0.309350] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 0.309380] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90004780000, using 4160k, total 4160k
[ 0.315773] Console: switching to colour frame buffer device 170x48
[ 0.321847] fb0: VESA VGA frame buffer device
[ 0.321882] intel_idle: MWAIT substates: 0x21120
[ 0.321884] intel_idle: v0.4 model 0x2A
[ 0.321887] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 0.322122] GHES: HEST is not enabled!
[ 0.322261] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.323099] Linux agpgart interface v0.103
[ 0.323175] rtc_cmos 00:03: RTC can wake from S4
[ 0.323405] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 0.323444] rtc_cmos 00:03: alarms up to one month, 242 bytes nvram, hpet irqs
[ 0.323464] Intel P-state driver initializing.
[ 0.323700] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.323974] TCP: cubic registered
[ 0.324249] NET: Registered protocol family 10
[ 0.324810] NET: Registered protocol family 17
[ 0.325630] Loading compiled-in X.509 certificates
[ 0.325667] registered taskstats version 1
[ 0.326469] Magic number: 2:425:406
[ 0.326624] rtc_cmos 00:03: setting system clock to 2014-10-27 00:25:43 UTC (1414369543)
[ 0.326771] PM: Hibernation image not present or could not be loaded.
[ 0.328979] Freeing unused kernel memory: 1140K (ffffffff818e5000 - ffffffff81a02000)
[ 0.328984] Write protecting the kernel read-only data: 8192k
[ 0.334234] Freeing unused kernel memory: 752K (ffff880001544000 - ffff880001600000)
[ 0.336362] Freeing unused kernel memory: 336K (ffff8800017ac000 - ffff880001800000)
[ 0.352574] random: systemd-tmpfile urandom read with 1 bits of entropy available
[ 0.355532] systemd-udevd[47]: starting version 216
[ 0.387858] ACPI: bus type USB registered
[ 0.387913] usbcore: registered new interface driver usbfs
[ 0.387936] usbcore: registered new interface driver hub
[ 0.388039] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 0.388042] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 0.391270] usbcore: registered new device driver usb
[ 0.392129] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.392223] sdhci: Secure Digital Host Controller Interface driver
[ 0.392228] sdhci: Copyright(c) Pierre Ossman
[ 0.392414] ehci-pci: EHCI PCI platform driver
[ 0.392656] ehci-pci 0000:00:1a.0: EHCI Host Controller
[ 0.392671] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 0.392674] sdhci-pci 0000:02:00.1: SDHCI controller found [14e4:16bc] (rev 10)
[ 0.392714] ehci-pci 0000:00:1a.0: debug port 2
[ 0.393158] sdhci-pci 0000:02:00.1: No vmmc regulator found
[ 0.393163] sdhci-pci 0000:02:00.1: No vqmmc regulator found
[ 0.395522] mmc0: SDHCI controller on PCI [0000:02:00.1] using ADMA
[ 0.397372] SCSI subsystem initialized
[ 0.400613] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[ 0.400649] ehci-pci 0000:00:1a.0: irq 21, io mem 0xe0705800
[ 0.402598] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.402906] libata version 3.00 loaded.
[ 0.408631] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 0.408994] hub 1-0:1.0: USB hub found
[ 0.409010] hub 1-0:1.0: 3 ports detected
[ 0.409474] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 0.409486] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 0.409509] ehci-pci 0000:00:1d.0: debug port 2
[ 0.413433] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 0.413449] ehci-pci 0000:00:1d.0: irq 19, io mem 0xe0705c00
[ 0.421967] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 0.422311] hub 2-0:1.0: USB hub found
[ 0.422325] hub 2-0:1.0: 3 ports detected
[ 0.422611] ahci 0000:00:1f.2: version 3.0
[ 0.422819] ahci 0000:00:1f.2: irq 26 for MSI/MSI-X
[ 0.422858] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
[ 0.422890] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 6 Gbps 0x1 impl SATA mode
[ 0.422896] ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck stag pm led clo pio slum part apst
[ 0.425306] scsi host0: ahci
[ 0.427777] scsi host1: ahci
[ 0.430423] scsi host2: ahci
[ 0.431139] scsi host3: ahci
[ 0.431256] ata1: SATA max UDMA/133 abar m2048@0xe0705000 port 0xe0705100 irq 26
[ 0.431260] ata2: DUMMY
[ 0.431262] ata3: DUMMY
[ 0.431265] ata4: DUMMY
[ 0.475720] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.715469] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 0.748738] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 0.760911] ata1.00: ATA-8: MKNSSDCR120GB-7, 582ABBF0, max UDMA/133
[ 0.760921] ata1.00: 234441648 sectors, multi 1: LBA48 NCQ (depth 31/32), AA
[ 0.770881] ata1.00: configured for UDMA/133
[ 0.771363] scsi 0:0:0:0: Direct-Access ATA MKNSSDCR120GB-7 BBF0 PQ: 0 ANSI: 5
[ 0.782066] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
[ 0.782627] sd 0:0:0:0: [sda] Write Protect is off
[ 0.782637] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.782810] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.785152] sda: sda1 sda2 sda3
[ 0.786014] sd 0:0:0:0: [sda] Attached SCSI disk
[ 0.839907] hub 1-1:1.0: USB hub found
[ 0.840119] hub 1-1:1.0: 4 ports detected
[ 0.935913] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 0.945475] usb 2-1: new high-speed USB device number 2 using ehci-pci
[ 1.069643] hub 2-1:1.0: USB hub found
[ 1.069827] hub 2-1:1.0: 4 ports detected
[ 1.148949] usb 1-1.1: new full-speed USB device number 3 using ehci-pci
[ 1.233928] usb 1-1.1: string descriptor 0 read error: -22
[ 1.290134] EXT4-fs (sda1): re-mounted. Opts: data=ordered
[ 1.305272] tsc: Refined TSC clocksource calibration: 1097.506 MHz
[ 1.315437] usb 1-1.3: new high-speed USB device number 4 using ehci-pci
[ 1.344309] systemd-udevd[136]: starting version 216
[ 1.352295] systemd-journald[119]: Received request to flush runtime journal from PID 1
[ 1.607498] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 1.610413] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
[ 1.610471] ACPI: Lid Switch [LID0]
[ 1.610565] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[ 1.610572] ACPI: Power Button [PWRB]
[ 1.610653] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input3
[ 1.610657] ACPI: Sleep Button [TPAD]
[ 1.610758] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 1.610763] ACPI: Power Button [PWRF]
[ 1.626490] mei_me 0000:00:16.0: irq 27 for MSI/MSI-X
[ 1.645724] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 1.645942] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input5
[ 1.653739] thermal LNXTHERM:00: registered as thermal_zone0
[ 1.653745] ACPI: Thermal Zone [THRM] (0 C)
[ 1.660772] [Firmware Bug]: battery: (dis)charge rate invalid.
[ 1.665282] ACPI: Battery Slot [BATX] (battery present)
[ 1.666038] ACPI: AC Adapter [AC] (on-line)
[ 1.681337] ACPI Warning: SystemIO range 0x0000000000000528-0x000000000000052f conflicts with OpRegion 0x0000000000000500-0x000000000000057f (\PMIO) (20140724/utaddress-258)
[ 1.681351] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 1.681358] ACPI Warning: SystemIO range 0x00000000000004c0-0x00000000000004cf conflicts with OpRegion 0x0000000000000480-0x00000000000004eb (\GPIO) (20140724/utaddress-258)
[ 1.681364] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 1.681367] ACPI Warning: SystemIO range 0x00000000000004b0-0x00000000000004bf conflicts with OpRegion 0x0000000000000480-0x00000000000004eb (\GPIO) (20140724/utaddress-258)
[ 1.681374] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 1.681376] ACPI Warning: SystemIO range 0x0000000000000480-0x00000000000004af conflicts with OpRegion 0x0000000000000480-0x00000000000004eb (\GPIO) (20140724/utaddress-258)
[ 1.681382] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 1.681385] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 1.688249] [drm] Initialized drm 1.1.0 20060810
[ 1.691201] pps_core: LinuxPPS API ver. 1 registered
[ 1.691207] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.700706] i801_smbus 0000:00:1f.3: SMBus using PCI Interrupt
[ 1.701200] PTP clock support registered
[ 1.706524] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 1.752871] tg3.c:v3.137 (May 11, 2014)
[ 1.753314] Adding 8167872k swap on /dev/sda2. Priority:-1 extents:1 across:8167872k SSFS
[ 1.757127] Bluetooth: Core ver 2.19
[ 1.757151] NET: Registered protocol family 31
[ 1.757154] Bluetooth: HCI device and connection manager initialized
[ 1.757166] Bluetooth: HCI socket layer initialized
[ 1.757170] Bluetooth: L2CAP socket layer initialized
[ 1.757180] Bluetooth: SCO socket layer initialized
[ 1.771585] usbcore: registered new interface driver btusb
[ 1.771864] snd_hda_intel 0000:00:1b.0: irq 28 for MSI/MSI-X
[ 1.777240] cfg80211: Calling CRDA to update world regulatory domain
[ 1.812626] sound hdaudioC0D0: autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[ 1.812635] sound hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 1.812640] sound hdaudioC0D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[ 1.812643] sound hdaudioC0D0: mono: mono_out=0x0
[ 1.812646] sound hdaudioC0D0: inputs:
[ 1.812650] sound hdaudioC0D0: Internal Mic=0x1b
[ 1.812654] sound hdaudioC0D0: Mic=0x19
[ 1.819178] tg3 0000:02:00.0 eth0: Tigon3 [partno(BCM57785) rev 57785100] (PCI Express) MAC address 20:89:84:c7:a0:92
[ 1.819187] tg3 0000:02:00.0 eth0: attached PHY is 57765 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1])
[ 1.819192] tg3 0000:02:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 1.819196] tg3 0000:02:00.0 eth0: dma_rwctrl[00000001] dma_mask[64-bit]
[ 1.834640] media: Linux media interface: v0.10
[ 1.845475] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/sound/card0/hdaudioC0D0/input7
[ 1.849543] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 1.850477] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 1.850623] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 1.851058] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[ 1.851353] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[ 1.860140] iTCO_vendor_support: vendor-support=0
[ 1.861704] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 1.861764] iTCO_wdt: Found a Panther Point TCO device (Version=2, TCOBASE=0x0560)
[ 1.862721] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 1.863690] Linux video capture interface: v2.00
[ 1.875723] usbcore: registered new interface driver ath3k
[ 1.914247] tg3 0000:02:00.0 enp2s0f0: renamed from eth0
[ 1.926001] systemd-udevd[145]: renamed network interface eth0 to enp2s0f0
[ 1.938186] usb 1-1.1: USB disconnect, device number 3
[ 1.944872] uvcvideo: Found UVC 1.00 device HD WebCam (04f2:b336)
[ 1.953353] input: HD WebCam as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input13
[ 1.953679] usbcore: registered new interface driver uvcvideo
[ 1.953684] USB Video Class driver (1.1.1)
[ 1.997073] intel_rapl: Found RAPL domain package
[ 1.997080] intel_rapl: Found RAPL domain core
[ 1.997083] intel_rapl: Found RAPL domain uncore
[ 1.999325] [drm] Memory usable by graphics device = 2048M
[ 1.999330] [drm] Replacing VGA console driver
[ 1.999337] checking generic (d0000000 410000) vs hw (d0000000 10000000)
[ 1.999340] fb: switching to inteldrmfb from VESA VGA
[ 1.999399] Console: switching to colour dummy device 80x25
[ 2.006114] i915 0000:00:02.0: irq 29 for MSI/MSI-X
[ 2.006130] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 2.006133] [drm] Driver supports precise vblank timestamp query.
[ 2.006275] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 2.010165] input: Cypress APA Trackpad (cyapa) as /devices/pci0000:00/0000:00:1f.3/i2c-0/0-0067/input/input14
[ 2.014824] mousedev: PS/2 mouse device common for all mice
[ 2.037823] ath: phy0: ASPM enabled: 0x43
[ 2.037831] ath: EEPROM regdomain: 0x6c
[ 2.037834] ath: EEPROM indicates we should expect a direct regpair map
[ 2.037838] ath: Country alpha2 being used: 00
[ 2.037840] ath: Regpair used: 0x6c
[ 2.044014] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 2.044617] ieee80211 phy0: Atheros AR9462 Rev:2 mem=0xffffc90004980000, irq=17
[ 2.050867] ath9k 0000:01:00.0 wlp1s0: renamed from wlan0
[ 2.054438] fbcon: inteldrmfb (fb0) is primary device
[ 2.054543] Console: switching to colour frame buffer device 170x48
[ 2.054559] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 2.054563] i915 0000:00:02.0: registered panic notifier
[ 2.066878] systemd-udevd[145]: renamed network interface wlan0 to wlp1s0
[ 2.070905] [drm] Initialized i915 1.6.0 20140725 for 0000:00:02.0 on minor 0
[ 2.125455] usb 1-1.1: new full-speed USB device number 5 using ehci-pci
[ 2.154830] tg3 0000:02:00.0: irq 30 for MSI/MSI-X
[ 2.154842] tg3 0000:02:00.0: irq 31 for MSI/MSI-X
[ 2.154849] tg3 0000:02:00.0: irq 32 for MSI/MSI-X
[ 2.714571] Switched to clocksource tsc
[ 2.714588] IPv6: ADDRCONF(NETDEV_UP): enp2s0f0: link is not ready
[ 2.731648] usb 1-1.1: string descriptor 0 read error: -22
[ 2.850571] random: nonblocking pool is initializedlsusb
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 004: ID 04f2:b336 Chicony Electronics Co., Ltd
Bus 001 Device 005: ID 0489:e04e Foxconn / Hon Hai
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hubOffline
Updated the system, now using arch kernel 3.17.1-1
Problem still exists.
The C710 has USB 2.0 ports, but the linux-chromebook packages are configured to only use USB 3.0, so they won't work with the C710.
See https://bbs.archlinux.org/viewtopic.php?id=180600 for more info on the USB error. I suspect this error isn't related to the boot failures, based on looking at the related kernel code, but not sure. You might try turning up the kernel log level output to receive more info in dmesg and the boot logs, and then view them on the first successful boot after a bad boot for clues.
Offline