You are not logged in.

Pages: 1

#1 2015-10-27 19:32:53

LCvanDinteren
Member
From: Netherlands
Registered: 2015-10-27
Posts: 153

[Solved] [E19] Compositor Warning: Display driver does not support...

Hello everyone,
I am getting the following compositor warning:

Your display driver does not support OpenGL, GLSL shaders or no OpenGL engines were compiled or installed for Evas or Ecore-Evas. Falling back to software engine.

You will need an OpenGL 2.0 (or OpenGL ES 2.0) capable GPU to use OpenGL with compositing.

My setup:
I did a clean arch install with enlightenment and XDM (will probably uninstall XDM soon... I don't like it)
I got 2 ati radeon 7770 cards, both recognized, 3 monitors connected to Card0, all recognized and i can expand screens on all three using xrandr.
I installed the unofficial drivers using 

sudo pacman -S xf86-video-ati

Created the necessary .conf files in /etc/X11/Xorg.conf.d/ to initialize on startup. (will post .conf files on request, but I don't think it is necessary)
After login I have 3 cloned displays and need to manually configure with xrandr.
I think the issue is in the warning I get on boot up, if you think it is unrelated I will have another careful look at my .conf files.

Any ideas on the warning? I've done some googling but can't find much, mainly some raspberry pi stuff.

Below is the start of my Xorg.0.log (after this part it shows supported devices and resolutions)

~ » cat /var/log/Xorg.0.log                                                                              
[     9.432]
X.Org X Server 1.17.2
Release Date: 2015-06-16
[     9.432] X Protocol Version 11, Revision 0
[     9.432] Build Operating System: Linux 4.0.4-2-ARCH x86_64
[     9.432] Current Operating System: Linux archy 4.2.3-1-ARCH #1 SMP PREEMPT Sat Oct 3 18:52:50 CEST 2015 x86_64
[     9.432] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=3805f2d3-7c49-470a-8584-361473f22b2b rw quie
t
[     9.432] Build Date: 17 July 2015  05:38:19PM
[     9.432]
[     9.432] Current version of pixman: 0.32.8
[     9.432] 	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
[     9.432] Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[     9.432] (==) Log file: "/var/log/Xorg.0.log", Time: Tue Oct 27 19:46:47 2015
[     9.432] (==) Using config file: "/etc/X11/xorg.conf"
[     9.432] (==) Using config directory: "/etc/X11/xorg.conf.d"
[     9.432] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[     9.432] (==) ServerLayout "Main"
[     9.432] (**) |-->Screen "DP" (0)
[     9.432] (**) |   |-->Monitor "DP"
[     9.432] (**) |   |-->Device "Card0"
[     9.433] (**) |-->Screen "DVI" (1)
[     9.433] (**) |   |-->Monitor "DVI"
[     9.433] (**) |   |-->Device "Card0"
[     9.433] (**) |-->Screen "HDMI" (2)
[     9.433] (**) |   |-->Monitor "HDMI"
[     9.433] (**) |   |-->Device "Card0"
[     9.433] (==) Automatically adding devices
[     9.433] (==) Automatically enabling devices
[     9.433] (==) Automatically adding GPU devices
[     9.433] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[     9.433] 	Entry deleted from font path.
[     9.433] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[     9.433] 	Entry deleted from font path.
[     9.433] 	(Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[     9.433] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[     9.433] 	Entry deleted from font path.
[     9.433] 	(Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[     9.433] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[     9.433] 	Entry deleted from font path.
[     9.433] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[     9.433] 	Entry deleted from font path.
[     9.433] 	(Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[     9.433] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[     9.433] 	Entry deleted from font path.
[     9.433] 	(Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[     9.433] (**) FontPath set to:
	/usr/share/fonts/misc/,
	/usr/share/fonts/TTF/,
	/usr/share/fonts/OTF/,
	/usr/share/fonts/misc/,
	/usr/share/fonts/TTF/,
	/usr/share/fonts/OTF/
[     9.433] (**) ModulePath set to "/usr/lib/xorg/modules"
[     9.433] (II) The server relies on udev to provide the list of input devices.
	If no devices become available, reconfigure udev or disable AutoAddDevices.
[     9.433] (II) Loader magic: 0x817d60
[     9.433] (II) Module ABI versions:
[     9.433] 	X.Org ANSI C Emulation: 0.4
[     9.433] 	X.Org Video Driver: 19.0
[     9.433] 	X.Org XInput driver : 21.1
[     9.433] 	X.Org Server Extension : 9.0
[     9.435] (EE) systemd-logind: failed to get session: PID 482 does not belong to any known session
[     9.436] (II) xfree86: Adding drm device (/dev/dri/card0)
[     9.436] (II) xfree86: Adding drm device (/dev/dri/card1)
[     9.439] (--) PCI:*(0:2:0:0) 1002:683d:1043:0429 rev 0, Mem @ 0xc0000000/268435456, 0xfb980000/262144, I/O @ 0x0000
9000/256, BIOS @ 0x????????/131072
[     9.439] (--) PCI: (0:3:0:0) 1002:683d:1043:0429 rev 0, Mem @ 0xd0000000/268435456, 0xfba80000/262144, I/O @ 0x0000
a000/256, BIOS @ 0x????????/131072
[     9.439] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[     9.439] (II) "glx" will be loaded. This was enabled by default and also specified in the config file.
[     9.439] (II) LoadModule: "glx"
[     9.439] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[     9.440] (II) Module glx: vendor="X.Org Foundation"
[     9.440] 	compiled for 1.17.2, module version = 1.0.0
[     9.440] 	ABI class: X.Org Server Extension, version 9.0
[     9.440] (==) AIGLX enabled
[     9.440] (II) LoadModule: "radeon"
[     9.440] (II) Loading /usr/lib/xorg/modules/drivers/radeon_drv.so
[     9.440] (II) Module radeon: vendor="X.Org Foundation"
[     9.440] 	compiled for 1.17.0, module version = 7.5.0
[     9.440] 	Module class: X.Org Video Driver
[     9.440] 	ABI class: X.Org Video Driver, version 19.0
[     9.440] (II) RADEON: Driver for ATI Radeon chipsets:
[     9.443] (WW) xf86OpenConsole: setpgid failed: Operation not permitted
[     9.444] (WW) xf86OpenConsole: setsid failed: Operation not permitted
[     9.444] (II) [KMS] Kernel modesetting enabled.
[     9.444] (II) [KMS] Kernel modesetting enabled.
[     9.444] (II) RADEON(0): Creating default Display subsection in Screen section
	"DP" for depth/fbbpp 16/16
[     9.444] (**) RADEON(0): Depth 16, (--) framebuffer bpp 16
[     9.444] (II) RADEON(0): Pixel depth = 16 bits stored in 2 bytes (16 bpp pixmaps)
[     9.444] (==) RADEON(0): Default visual is TrueColor
[     9.444] (==) RADEON(0): RGB weight 565
[     9.444] (II) RADEON(0): Using 6 bits per RGB (8 bit DAC)
[     9.444] (--) RADEON(0): Chipset: "VERDE" (ChipID = 0x683d)
[     9.444] (II) Loading sub module "dri2"
[     9.444] (II) LoadModule: "dri2"
[     9.444] (II) Module "dri2" already built-in
[     9.444] (WW) RADEON(0): glamor requires depth >= 24, disabling.
[     9.444] (II) Loading sub module "shadow"
[     9.444] (II) LoadModule: "shadow"
[     9.444] (II) Loading /usr/lib/xorg/modules/libshadow.so
[     9.444] (II) Module shadow: vendor="X.Org Foundation"
[     9.444] 	compiled for 1.17.2, module version = 1.1.0
[     9.444] 	ABI class: X.Org ANSI C Emulation, version 0.4
[     9.444] (II) RADEON(0): KMS Color Tiling: disabled
[     9.444] (II) RADEON(0): KMS Color Tiling 2D: disabled
[     9.444] (II) RADEON(0): KMS Pageflipping: enabled
[     9.444] (II) RADEON(0): SwapBuffers wait for vsync: enabled
[     9.483] (II) RADEON(0): Output DisplayPort-0 using monitor section DP
[     9.543] (II) RADEON(0): Output HDMI-0 using monitor section HDMI
[     9.543] (**) RADEON(0): Option "RightOf" "DVI"
[     9.576] (II) RADEON(0): Output DVI-0 using monitor section DVI
[     9.576] (**) RADEON(0): Option "RightOf" "DP"
[     9.587] (II) RADEON(0): Output DVI-1 has no monitor section
[     9.626] (II) RADEON(0): EDID for output DisplayPort-0
[     9.626] (II) RADEON(0): Manufacturer: SAM  Model: 5c4  Serial#: 1162228275
[     9.626] (II) RADEON(0): Year: 2010  Week: 8
[     9.626] (II) RADEON(0): EDID Version: 1.3
[     9.626] (II) RADEON(0): Digital Display Input
[     9.626] (II) RADEON(0): Max Image Size [cm]: horiz.: 51  vert.: 29
[     9.627] (II) RADEON(0): Gamma: 2.20
[     9.627] (II) RADEON(0): DPMS capabilities: Off
[     9.627] (II) RADEON(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[     9.627] (II) RADEON(0): First detailed timing is preferred mode
[     9.627] (II) RADEON(0): redX: 0.640 redY: 0.330   greenX: 0.150 greenY: 0.060
[     9.627] (II) RADEON(0): blueX: 0.300 blueY: 0.600   whiteX: 0.312 whiteY: 0.329
[     9.627] (II) RADEON(0): Supported established timings:
[     9.627] (II) RADEON(0): 640x480@60Hz
[     9.627] (II) RADEON(0): 800x600@56Hz
[     9.627] (II) RADEON(0): 800x600@60Hz
[     9.627] (II) RADEON(0): 1024x768@60Hz
[     9.627] (II) RADEON(0): Manufacturer's mask: 0
[     9.627] (II) RADEON(0): Supported standard timings:
[     9.627] (II) RADEON(0): #0: hsize: 1280  vsize 800  refresh: 60  vid: 129
[     9.627] (II) RADEON(0): #1: hsize: 1280  vsize 960  refresh: 60  vid: 16513
[     9.627] (II) RADEON(0): #2: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
[     9.627] (II) RADEON(0): #3: hsize: 1440  vsize 900  refresh: 60  vid: 149
[     9.627] (II) RADEON(0): #4: hsize: 1600  vsize 1200  refresh: 60  vid: 16553
[     9.627] (II) RADEON(0): #5: hsize: 1680  vsize 1050  refresh: 60  vid: 179
[     9.627] (II) RADEON(0): Supported detailed timing:
[     9.627] (II) RADEON(0): clock: 148.5 MHz   Image Size:  510 x 287 mm
[     9.627] (II) RADEON(0): h_active: 1920  h_sync: 2008  h_sync_end 2052 h_blank_end 2200 h_border: 0
[     9.627] (II) RADEON(0): v_active: 1080  v_sync: 1084  v_sync_end 1089 v_blanking: 1125 v_border: 0
[     9.627] (II) RADEON(0): Ranges: V min: 56 V max: 60 Hz, H min: 30 H max: 81 kHz, PixClock max 175 MHz
[     9.627] (II) RADEON(0): Monitor name: SyncMaster
[     9.627] (II) RADEON(0): Serial No: H9MZ218009
[     9.627] (II) RADEON(0): EDID (in hex):
[     9.627] (II) RADEON(0): 	00ffffffffffff004c2dc40533324645
[     9.627] (II) RADEON(0): 	0814010380331d782ae9e1a354260f4c
[     9.627] (II) RADEON(0): 	9950542308008100814081809500a940
[     9.627] (II) RADEON(0): 	b30001010101023a801871382d40582c
[     9.627] (II) RADEON(0): 	4500fe1f1100001e000000fd00383c1e
[     9.627] (II) RADEON(0): 	5111000a202020202020000000fc0053
[     9.627] (II) RADEON(0): 	796e634d61737465720a2020000000ff
[     9.627] (II) RADEON(0): 	0048394d5a3231383030390a20200072
[     9.627] (II) RADEON(0): Printing probed modes for output DisplayPort-0

Greetings,
Leander

P.S.: This is my first post so please be gentle smile I've read the forum etiquette
If you need any further information, please ask and I will supply.

Last edited by LCvanDinteren (2015-10-28 08:11:39)

Offline

#2 2015-10-27 19:47:04

LCvanDinteren
Member
From: Netherlands
Registered: 2015-10-27
Posts: 153

Re: [Solved] [E19] Compositor Warning: Display driver does not support...

Some additional information, the output of: 

 glxinfo | grep -E 'OpenGL'
OpenGL vendor string: VMware, Inc.
OpenGL renderer string: Gallium 0.4 on llvmpipe (LLVM 3.7, 128 bits)
OpenGL version string: 3.0 Mesa 11.0.3
OpenGL shading language version string: 1.30
OpenGL context flags: (none)
OpenGL extensions:

Offline

#3 2015-10-27 20:19:35

ewaller
Administrator
From: Pasadena, CA
Registered: 2009-07-13
Posts: 19,797

Re: [Solved] [E19] Compositor Warning: Display driver does not support...

LCvanDinteren wrote:

Some additional information, the output of: 

 glxinfo | grep -E 'OpenGL'
OpenGL vendor string: VMware, Inc.
...

VMware?   I think you need to tell us more about your system.

Nothing is too wonderful to be true, if it be consistent with the laws of nature -- Michael Faraday
Sometimes it is the people no one can imagine anything of who do the things no one can imagine. -- Alan Turing
---
How to Ask Questions the Smart Way

Offline

#4 2015-10-27 20:21:45

LCvanDinteren
Member
From: Netherlands
Registered: 2015-10-27
Posts: 153

Re: [Solved] [E19] Compositor Warning: Display driver does not support...

What do you mean? I'm not running in VMware..

Offline

#5 2015-10-27 20:28:23

ewaller
Administrator
From: Pasadena, CA
Registered: 2009-07-13
Posts: 19,797

Re: [Solved] [E19] Compositor Warning: Display driver does not support...

The glxinfo reports that the vendor is VMware.  That is not what I would expect; but I have never uses ATI.
What packages related to mesa, ati, and opengl have you installed?

Nothing is too wonderful to be true, if it be consistent with the laws of nature -- Michael Faraday
Sometimes it is the people no one can imagine anything of who do the things no one can imagine. -- Alan Turing
---
How to Ask Questions the Smart Way

Offline

#6 2015-10-27 20:30:55

LCvanDinteren
Member
From: Netherlands
Registered: 2015-10-27
Posts: 153

Re: [Solved] [E19] Compositor Warning: Display driver does not support...

I installed all mesa packages (mesa, -demos, -libgl, -vdpau)
xf86-video-ati

none other as far as I recall..

Last edited by LCvanDinteren (2015-10-27 20:33:37)

Offline

#7 2015-10-27 20:46:23

jasonwryan
Anarchist
From: .nz
Registered: 2009-05-09
Posts: 30,424
Website

Re: [Solved] [E19] Compositor Warning: Display driver does not support...

Not an Installation issue, moving to NC...

Arch + dwm   •   Mercurial repos  •   Surfraw

Registered Linux User #482438

Offline

#8 2015-10-27 21:20:51

LCvanDinteren
Member
From: Netherlands
Registered: 2015-10-27
Posts: 153

Re: [Solved] [E19] Compositor Warning: Display driver does not support...

Thanks for moving jasonwryan.

In further news:
I reshuffled a little with my .conf files, the compositor warning is now gone and the glxinfo now says OpenGL vendor string: X.Org.
So I guess I made a mistake there somewhere.. now to fix my triple screen setup...

Current xorg.conf file: 

Section "ServerLayout"
	Identifier     "X.org Configured"
	Screen      0  "Screen0" 0 0
	Screen      1  "Screen1" RightOf "Screen0"
	Screen	    2  "Screen2" RightOf "Screen1"
	InputDevice    "Mouse0" "CorePointer"
	InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
	ModulePath   "/usr/lib/xorg/modules"
	FontPath     "/usr/share/fonts/misc/"
	FontPath     "/usr/share/fonts/TTF/"
	FontPath     "/usr/share/fonts/OTF/"
	FontPath     "/usr/share/fonts/Type1/"
	FontPath     "/usr/share/fonts/100dpi/"
	FontPath     "/usr/share/fonts/75dpi/"
EndSection

Section "Module"
	Load  "glx"
EndSection

Section "InputDevice"
	Identifier  "Keyboard0"
	Driver      "kbd"
EndSection

Section "InputDevice"
	Identifier  "Mouse0"
	Driver      "mouse"
	Option	    "Protocol" "auto"
	Option	    "Device" "/dev/input/mice"
	Option	    "ZAxisMapping" "4 5 6 7"
EndSection

Section "Monitor"
	Identifier   "Monitor0"
	VendorName   "Samsung"
	ModelName    "XL2370"
EndSection

Section "Monitor"
	Identifier   "Monitor1"
	VendorName   "iiyama"
	ModelName    "X2377HDS"
EndSection

Section "Monitor"
	Identifier   "Monitor2"
	VendorName   "Samsung"
	ModelName    "P2370"
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
        ### <percent>: "<f>%"
        ### [arg]: arg optional
        #Option     "Accel"              	# [<bool>]
        #Option     "SWcursor"           	# [<bool>]
        #Option     "EnablePageFlip"     	# [<bool>]
        #Option     "ColorTiling"        	# [<bool>]
        #Option     "ColorTiling2D"      	# [<bool>]
        #Option     "RenderAccel"        	# [<bool>]
        #Option     "SubPixelOrder"      	# [<str>]
        #Option     "AccelMethod"        	# <str>
        #Option     "EXAVSync"           	# [<bool>]
        #Option     "EXAPixmaps"         	# [<bool>]
        #Option     "ZaphodHeads"        	# <str>
        #Option     "EnablePageFlip"     	# [<bool>]
        #Option     "SwapbuffersWait"    	# [<bool>]
	Identifier  "Card0"
	Driver      "radeon"
	BusID       "PCI:2:0:0"
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
        ### <percent>: "<f>%"
        ### [arg]: arg optional
        #Option     "Accel"              	# [<bool>]
        #Option     "SWcursor"           	# [<bool>]
        #Option     "EnablePageFlip"     	# [<bool>]
        #Option     "ColorTiling"        	# [<bool>]
        #Option     "ColorTiling2D"      	# [<bool>]
        #Option     "RenderAccel"        	# [<bool>]
        #Option     "SubPixelOrder"      	# [<str>]
        #Option     "AccelMethod"        	# <str>
        #Option     "EXAVSync"           	# [<bool>]
        #Option     "EXAPixmaps"         	# [<bool>]
        #Option     "ZaphodHeads"        	# <str>
        #Option     "EnablePageFlip"     	# [<bool>]
        #Option     "SwapbuffersWait"    	# [<bool>]
	Identifier  "Card1"
	Driver      "radeon"
	BusID       "PCI:3:0:0"
EndSection

Section "Screen"
	Identifier "Screen0"
	Device     "Card0"
	Monitor    "Monitor0"
	SubSection "Display"
		Viewport   0 0
		Depth     1
	EndSubSection
	SubSection "Display"
		Viewport   0 0
		Depth     4
	EndSubSection
	SubSection "Display"
		Viewport   0 0
		Depth     8
	EndSubSection
	SubSection "Display"
		Viewport   0 0
		Depth     15
	EndSubSection
	SubSection "Display"
		Viewport   0 0
		Depth     16
	EndSubSection
	SubSection "Display"
		Viewport   0 0
		Depth     24
	EndSubSection
EndSection

Section "Screen"
	Identifier "Screen1"
	Device     "Card0"
	Monitor    "Monitor1"
	SubSection "Display"
		Viewport   0 0
		Depth     1
	EndSubSection
	SubSection "Display"
		Viewport   0 0
		Depth     4
	EndSubSection
	SubSection "Display"
		Viewport   0 0
		Depth     8
	EndSubSection
	SubSection "Display"
		Viewport   0 0
		Depth     15
	EndSubSection
	SubSection "Display"
		Viewport   0 0
		Depth     16
	EndSubSection
	SubSection "Display"
		Viewport   0 0
		Depth     24
	EndSubSection
EndSection

Section "Screen"
	Identifier "Screen2"
	Device     "Card0"
	Monitor    "Monitor2"
	SubSection "Display"
		Viewport   0 0
		Depth     1
	EndSubSection
	SubSection "Display"
		Viewport   0 0
		Depth     4
	EndSubSection
	SubSection "Display"
		Viewport   0 0
		Depth     8
	EndSubSection
	SubSection "Display"
		Viewport   0 0
		Depth     15
	EndSubSection
	SubSection "Display"
		Viewport   0 0
		Depth     16
	EndSubSection
	SubSection "Display"
		Viewport   0 0
		Depth     24
	EndSubSection
EndSection

Any obvious mistakes on my part?

Should I mark this thread as solved with the answer being in the .conf files and, if necessary, create a new thread for the monitor setup?

Thanks for the support!
I really like the fast responses.

Offline

#9 2015-10-27 21:42:20

headkase
Member
Registered: 2011-12-06
Posts: 1,977

Re: [Solved] [E19] Compositor Warning: Display driver does not support...

LCvanDinteren wrote:

Should I mark this thread as solved with the answer being in the .conf files and, if necessary, create a new thread for the monitor setup?

You should mark this thread as solved and then start a new thread for the different issue.  One issue per thread.  As a note, with this threads current title, Compositor Warning, nobody is now going to come into it expecting to give help for a triple monitor setup..

Offline

#10 2015-10-28 08:11:00

LCvanDinteren
Member
From: Netherlands
Registered: 2015-10-27
Posts: 153

Re: [Solved] [E19] Compositor Warning: Display driver does not support...

Yes I know, I thought the issue was in the openGL drivers rather than my config.. should've known better...

Offline

Pages: 1

Board footer

Powered by FluxBB