You are not logged in.
Pages: 1
Hello,
I just installed i3 on my laptop because kde plasma was draining my battery to fast but now i cant connect to my colleges wifi.
When i start sudo wifi-menu i get this: scanning for networks... nl80211: could not set interface 'p2p-dev-wl2s0' up
p2p-dev-wl2s0: failed to initialize driver interface
Then the wifi menu starts and i try to connect but nothing happens.
My classmate who is a more experianced arch user said my intefaces where doing fine but he didnt know what to do.
The laptop in question is a msi gt72 6qd dominator g
I hope you guys can help me.
Last edited by philipW (2017-03-22 23:51:48)
Offline
What are the output of systemctl list-unit-files --state=enabled and ip addr
?
Nothing is too wonderful to be true, if it be consistent with the laws of nature -- Michael Faraday
The shortest way to ruin a country is to give power to demagogues.— Dionysius of Halicarnassus
---
How to Ask Questions the Smart Way
Offline
lemme check
Offline
systemctl list-unit-files --state=enabled says:
UNIT FILE STATE
org.cups.cupsd.path enabled
autovt@.service enabled
avahi-daemon.service enabled
bluetooth.service enabled
dbus-org.bluez.service enabled
dbus-org.freedesktop.Avahi.service enabled
dbus-org.freedesktop.ModemManager1.service enabled
dbus-org.freedesktop.NetworkManager.service enabled
dbus-org.freedesktop.nm-dispatcher.service enabled
display-manager.service enabled
getty@.service enabled
haveged.service enabled
lightdm.service enabled
ModemManager.service enabled
NetworkManager-dispatcher.service enabled
NetworkManager.service enabled
org.cups.cupsd.service enabled
ufw.service enabled
avahi-daemon.socket enabled
org.cups.cupsd.socket enabled
remote-fs.target enabled
21 unit files listed.and ip addr says:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: enp4s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000
link/ether d8:cb:8a:f0:d1:62 brd ff:ff:ff:ff:ff:ff
3: wlp2s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000
link/ether 9a:59:73:1d:bf:14 brd ff:ff:ff:ff:ff:ff Last edited by philipW (2017-03-21 17:58:24)
Offline
Don't do that. If someone who is trying to help asks for the output of a command, paste it. In code tags:
https://wiki.archlinux.org/index.php/Co … s_and_code
Moving to NC...
Offline
oops sorry
Offline
systemctl list-unit-files --state=enabledsays everything is enabled
https://bbs.archlinux.org/viewtopic.php?id=57855
Please do not paraphrase the output of commands but post the output itself. Without providing the output there is no way to know which specific units are enabled.
Edit:
Grammar change what to which.
Last edited by loqs (2017-03-21 17:25:06)
Offline
philipW wrote:systemctl list-unit-files --state=enabledsays everything is enabled
https://bbs.archlinux.org/viewtopic.php?id=57855
Please do not paraphrase the output of commands but post the output itself. Without providing the output there is no way to know which specific units are enabled.
Edit:
Grammar change what to which.
fixed it
Offline
Stop / disable NetworkManager then please work through Wireless_network_configuration#Manual_setup
Edit:
To make sure that no network services are trying to control the interface I suggest rebooting the system and check the output of `$ ip address`
<NO-CARRIER,BROADCAST,MULTICAST,UP>should change to
<NO-CARRIER,BROADCAST,MULTICAST>Last edited by loqs (2017-03-21 18:45:18)
Offline
Stop / disable NetworkManager then please work through Wireless_network_configuration#Manual_setup
oke i will try that and report back when im done
Offline
I also have i3wm and used NetworkManager for a while, but few minutes ago I configured netctl https://wiki.archlinux.org/index.php/netctl and seems to work fine. Maybe this may help You.
Offline
I also have i3wm and used NetworkManager for a while, but few minutes ago I configured netctl https://wiki.archlinux.org/index.php/netctl and seems to work fine. Maybe this may help You.
Too many medicines does more harm than good.
He is already have networkmanager and modemmanager working, adding netctl to the list won't help.
Arch is home!
https://github.com/Docbroke
Offline
nowakpawel wrote:I also have i3wm and used NetworkManager for a while, but few minutes ago I configured netctl https://wiki.archlinux.org/index.php/netctl and seems to work fine. Maybe this may help You.
Too many medicines does more harm than good.
He is already have networkmanager and modemmanager working, adding netctl to the list won't help.
Also this seems somewhat ironic to me as nowakpawel has an open issue which could very well be caused by exactly this but instead of answering jasonwryan's question makes this ill advised suggestion.
Edit:
remove superfluous instead
Last edited by loqs (2017-03-22 01:44:08)
Offline
Just trying to help. My previous post about netctl was written about half year ago from my previous Arch installation where I also had problems with UEFI partitions and something went wrong and I remove Arch for few months, now I decided to install it once again and learn as much as I can
Sorry for mess I really want to clean my profile and close old posts. This topic about netctl is probably solved now, but I want to test it for few days before I marked it as so.
Offline
Sorry for not getting back -- busy night. The issue here is that you are using NetworkManager to control your WiFi. That is fine, but wifi-menu is a GUI tool for netctl. The two will fight with each other.
The appropriate tool for NetworkManager is nm-applet for a GUI interface, or nmcli or nmtui for a command line / curses interface.
Nothing is too wonderful to be true, if it be consistent with the laws of nature -- Michael Faraday
The shortest way to ruin a country is to give power to demagogues.— Dionysius of Halicarnassus
---
How to Ask Questions the Smart Way
Offline
Sorry for not getting back -- busy night. The issue here is that you are using NetworkManager to control your WiFi. That is fine, but wifi-menu is a GUI tool for netctl. The two will fight with each other.
The appropriate tool for NetworkManager is nm-applet for a GUI interface, or nmcli or nmtui for a command line / curses interface.
It worked!
I couldnt make much sense of nmcli but nmtui does the job.
thanks for the replies, people.
now i can finaly use i3.
Offline
Please always remember to mark the thread as [SOLVED] by editing your initial post - once it is ;-)
Offline
Pages: 1