You are not logged in.

#1 2019-07-13 03:29:37

rbrinson
Member
Registered: 2019-07-12
Posts: 16

[SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

I just bought the new Dell XPS 15 7590 (2019) laptop, and I wanted to install Arch Linux on it in place of Windows. I knew that it being new hardware could pose some challenges, but I believed that a distro running the latest Linux kernel would mitigate the problems. Case in point, the new Dell XPS 15 ships with a Killer Wi-Fi 6 AX1650 wireless network adapter. This is really just a rebranded Intel AX200 chip, which has supposedly had kernel support since version 5.1. Unfortunately, the Killer AX1650 doesn't advertise itself as an Intel AX200. So, it wasn't until Linux 5.2 that the Killer AX1650 was able to be properly detected.

So, I made and saved off a disk image of the Windows installation, and I proceeded to boot up the Arch Linux Live environment. I was able to complete the basic installation of an Arch Linux system on the Dell XPS 15 7590 using an ethernet dongle, and when I booted into the newly installed Arch Linux, I was happy to find:

$ uname -r
5.2.0-arch2-1-ARCH

I was very excited when I saw:

$ ip addr show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: wlp59s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether d0:ab:d5:15:54:00 brd ff:ff:ff:ff:ff:ff

Also, checking iw dev:

$ iw dev
phy#0
	Interface wlp59s0
		ifindex 2
		wdev 0x1
		addr d0:ab:d5:15:54:00
		type managed
		txpower 0.00 dBm
		multicast TXQ:
			qsz-byt	qsz-pkt	flows	drops	marks	overlmt	hashcoltx-bytes	tx-packets
			0	0	0	0	0	0	0	0

However, I noticed that the interface was DOWN. So, I proceeded to try to bring it up:

$ ip link set wlp59s0 up
RTNETLINK answers: Connection timed out

So, then I was disappointed, and I began to poke through things to see what was wrong. The first thing I checked was lspci to see what it was saying about the network adapter and the module/driver being used. I've abbreviated the output to just the network adapter, but if anyone needs to see additional output, just let me know.

$ lspci -v
...
3b:00.0 Network controller: Intel Corporation Device 2723 (rev 1a)
	Subsystem: Bigfoot Networks, Inc. Device 1654
	Flags: bus master, fast devsel, latency 0, IRQ 16
	Memory at ed400000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: [c8] Power Management version 3
	Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
	Capabilities: [40] Express Endpoint, MSI 00
	Capabilities: [80] MSI-X: Enable+ Count=16 Masked-
	Capabilities: [100] Advanced Error Reporting
	Capabilities: [14c] Latency Tolerance Reporting
	Capabilities: [154] L1 PM Substates
	Kernel driver in use: iwlwifi
	Kernel modules: iwlwifi
...

So, it is definitely picking the correct driver. I then checked dmesg for iwlwifi. I saved the entire dmesg output if further information is needed from there.

$ dmesg | grep iwlwifi
[    2.481359] iwlwifi 0000:3b:00.0: enabling device (0000 -> 0002)
[    2.493380] iwlwifi 0000:3b:00.0: Found debug destination: EXTERNAL_DRAM
[    2.493381] iwlwifi 0000:3b:00.0: Found debug configuration: 0
[    2.493514] iwlwifi 0000:3b:00.0: loaded firmware version 48.13675109.0 op_mode iwlmvm
[    2.583805] iwlwifi 0000:3b:00.0: Detected Killer(R) Wi-Fi 6 AX1650x 160MHz Wireless Network Adapter (200NGW), REV=0x340
[    2.597598] iwlwifi 0000:3b:00.0: Applying debug destination EXTERNAL_DRAM
[    2.597749] iwlwifi 0000:3b:00.0: Allocated 0x00400000 bytes for firmware monitor.
[    2.771649] iwlwifi 0000:3b:00.0: base HW address: d0:ab:d5:15:54:00
[    2.790099] iwlwifi 0000:3b:00.0 wlp59s0: renamed from wlan0
[  380.174498] Modules linked in: hid_multitouch snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic hid_generic mei_hdcp mei_wdt iTCO_wdt iTCO_vendor_support joydev mousedev arc4 uvcvideo btusb videobuf2_vmalloc videobuf2_memops btrtl videobuf2_v4l2 btbcm btintel videobuf2_common bluetooth videodev media ecdh_generic cdc_acm ecc intel_rapl x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel kvm iwlmvm nouveau i915 irqbypass mac80211 sof_pci_dev snd_sof_intel_hda_common snd_sof_intel_hda snd_sof_intel_byt snd_sof_intel_ipc snd_sof snd_sof_xtensa_dsp snd_soc_skl snd_soc_hdac_hda snd_hda_ext_core snd_soc_skl_ipc snd_soc_sst_ipc snd_soc_sst_dsp snd_soc_acpi_intel_match snd_soc_acpi iwlwifi snd_soc_core crct10dif_pclmul ttm crc32_pclmul i2c_algo_bit ghash_clmulni_intel snd_compress drm_kms_helper ac97_bus snd_pcm_dmaengine dell_laptop snd_hda_intel ledtrig_audio dell_wmi snd_hda_codec drm idma64 aesni_intel dell_smbios cfg80211 snd_hda_core snd_hwdep snd_pcm aes_x86_64 crypto_simd

This output makes me think that it has correctly identified the network adapter as a Killer AX1650, and is loading up the iwlmvm firmware, which is correct according to the Linux Wireless Wiki.

I then checked dmesg for firmware:

$ dmesg | grep firmware
[    0.168772] Spectre V2 : Enabling Restricted Speculation for firmware calls
[    2.479682] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    2.512687] iwlwifi 0000:3b:00.0: loaded firmware version 48.13675109.0 op_mode iwlmvm
[    2.601407] iwlwifi 0000:3b:00.0: Allocated 0x00400000 bytes for firmware monitor.
[    2.626755] [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4)
[  357.558471] iwlwifi 0000:3b:00.0: Loaded firmware version: 48.13675109.0
[  369.505267] iwlwifi 0000:3b:00.0: Loaded firmware version: 48.13675109.0
[  370.042012] iwlwifi 0000:3b:00.0: loaded firmware version 48.13675109.0 op_mode iwlmvm
[  370.055127] iwlwifi 0000:3b:00.0: Allocated 0x00400000 bytes for firmware monitor.
[  417.291919] iwlwifi 0000:3b:00.0: Loaded firmware version: 48.13675109.0

I have checked rfkill to see if something was blocking the wireless network adapter, but nothing showed up there:

$ rfkill list
0: hci0: Bluetooth
	Soft blocked: no
	Hard blocked: no
1: phy0: Wireless LAN
	Soft blocked: no
	Hard blocked: no

I looked at lsmod to see if the modules were loaded:

$ lsmod | grep iwlwifi
iwlwifi               380928  1 iwlmvm
cfg80211              839680  3 iwlmvm,iwlwifi,mac80211
$ lsmod | grep iwlmvm
iwlmvm                454656  0
mac80211              983040  1 iwlmvm
iwlwifi               380928  1 iwlmvm
cfg80211              839680  3 iwlmvm,iwlwifi,mac80211

I did see that there is an Arch Wiki page concerning the Dell XPS 15 7590, and it does have a Wifi section. However, I have seen these instructions before on the Killer Networking support site. However, since I'm running Linux 5.2, and it is properly detecting the Killer AX1650, I don't think I need to build the iwlwifi driver or pull in firmware. I think that the driver and firmware in Linux 5.2 and the latest linux-firmware package are already current. I have also tried disabling bluetooth in the BIOS to make sure that bluetooth wasn't interfering with the wireless network adapter, but no joy.

Can anyone see what might be causing me to not be able bring up the detected wlp59s0 interface? If there is anymore information that you need me to provide, please let me know. Thank you for any help you can provide!

Last edited by rbrinson (2019-07-20 02:27:43)

Offline

#2 2019-07-13 04:01:56

jasonwryan
Anarchist
From: .nz
Registered: 2009-05-09
Posts: 30,424
Website

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

You could try disabling power saving https://wiki.archlinux.org/index.php/Wi … on#iwlwifi or using the git firmware package to see if that helps.


Arch + dwm   •   Mercurial repos  •   Surfraw

Registered Linux User #482438

Offline

#3 2019-07-13 08:40:16

Noxult
Member
Registered: 2019-07-13
Posts: 12

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

Same error. It should be noted that Wifi works well on Linux 5.1.16 following the instruction given on the Killer support site.

On Linux 5.1.16

$ lsmod | grep iwlwifi
iwlwifi               417792  1 iwlmvm
cfg80211              786432  3 iwlmvm,iwlwifi,mac80211
compat                 16384  4 iwlmvm,iwlwifi,mac80211,cfg80211
$ lsmod | grep iwlmvm
iwlmvm                491520  0
mac80211              905216  1 iwlmvm
iwlwifi               417792  1 iwlmvm
cfg80211              786432  3 iwlmvm,iwlwifi,mac80211
compat                 16384  4 iwlmvm,iwlwifi,mac80211,cfg80211
$ dmesg
[    2.732256] iwlwifi 0000:3b:00.0: enabling device (0000 -> 0002)
[    2.742592] iwlwifi 0000:3b:00.0: Direct firmware load for iwl-dbg-cfg.ini failed with error -2
[    2.742617] iwlwifi 0000:3b:00.0: Direct firmware load for iwlwifi-cc-a0-51.ucode failed with error -2
[    2.742627] iwlwifi 0000:3b:00.0: Direct firmware load for iwlwifi-cc-a0-50.ucode failed with error -2
[    2.742634] iwlwifi 0000:3b:00.0: Direct firmware load for iwlwifi-cc-a0-49.ucode failed with error -2
[    2.743793] iwlwifi 0000:3b:00.0: TLV_FW_FSEQ_VERSION: FSEQ Version: 43.2.23.17
[    2.743795] iwlwifi 0000:3b:00.0: Found debug destination: EXTERNAL_DRAM
[    2.743796] iwlwifi 0000:3b:00.0: Found debug configuration: 0
[    2.744043] iwlwifi 0000:3b:00.0: loaded firmware version 48.13675109.0 op_mode iwlmvm
[    2.816589] iwlwifi 0000:3b:00.0: Detected Killer(R) Wi-Fi 6 AX1650x 160MHz Wireless Network Adapter (200NGW), REV=0x340
[    2.829810] iwlwifi 0000:3b:00.0: Applying debug destination EXTERNAL_DRAM
[    2.829957] iwlwifi 0000:3b:00.0: Allocated 0x00400000 bytes for firmware monitor.

On Linux 5.2.0 the dmesg gives something different. I've taken a photo but did not take a copy, the message is something like this:

loaded firmware version 48.13675109.0
0x00000084 | NMI_INTERRUPT_UNKNOWN
... | trm_hw_status0
... | trm_hw_status2
... | branchlink2
... | interruptlink1
... | interruptlink2
... | data1
... | data2
...
... | FSEQ_ERROR_CODE
...
Firmware not running - cannot dump error
Error sending GEO_TX_POWER_LIMIT: time out after 2000ms.

Even if you backport and do some compiling stuff things doesn't change.

Some relevant issues : https://bbs.archlinux.org/viewtopic.php?id=247575
But in my case downgrading linux-firmware alone doesn't work. And when running Linux 5.1.16 with the latest linux-firmware (linux-firmware 20190628.70e4394-1) there is no issue.

Moreover, it seems that on Linux 5.2 iwlwifi-Qu-b0-hr-b0-48 or some other firmware is being tried to be loaded, while one that is ought to be loaded is iwlwifi-cc-a0-48; I have downgraded the kernel to 5.1.16, so I cannot confirm.

Last edited by Noxult (2020-02-13 17:48:45)

Offline

#4 2019-07-13 19:15:35

rbrinson
Member
Registered: 2019-07-12
Posts: 16

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

Hey, @Noxult, thank you for the reply. I followed the link you posted to bbs.archlinux.org, and following that rabbit trail, it seems like there are updates coming to iwlwifi which will hopefully fix this problem, though I'm not sure how long before they will be in a released version of the kernel. Hopefully, it will all work in the next release of the 5.2.x series. In the meantime, I was going to try doing as you suggested and use Linux 5.1.16. However, that immediately presented a few problems.

  1. How can I even get the Arch package for Linux 5.1.16, as it no longer appears in the Core repository? (The branch does exist in the Arch git repo.)

  2. Once I have the Arch Package for Linux 5.1.16, how do I apply the patch referenced on the Killer Networking website?

  3. Does Arch have a special way that they make the kernel and modules and get them installed?

Sorry, I know that's a lot of info to ask. I've never patched the Linux kernel, and the last time that I configured and compiled Linux was many years ago on Gentoo. So, I'm rusty, and I'm not familiar with the ins and outs of building packages on Arch. If there's any way you can help or point to the Internet documentation that you use when doing this, I would greatly appreciate it.

Offline

#5 2019-07-13 21:51:38

loqs
Member
Registered: 2014-03-06
Posts: 17,196

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

@rbrinson what is the full dmesg output from linux 5.2?

Offline

#6 2019-07-13 23:21:28

rbrinson
Member
Registered: 2019-07-12
Posts: 16

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

Hi, @loqs. Thank you for being willing to take a look. The full dmesg output from Linux 5.2 is:

[    0.000000] Linux version 5.2.0-arch2-1-ARCH (builduser@heftig-101614) (gcc version 9.1.0 (GCC)) #1 SMP PREEMPT Mon Jul 8 18:18:54 UTC 2019
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=df4369a4-2b53-4c91-9968-e7e6109ffcb6 rw audit=0 loglevel=3 quiet
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   Hygon HygonGenuine
[    0.000000]   Centaur CentaurHauls
[    0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x008: 'MPX bounds registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x010: 'MPX CSR'
[    0.000000] x86/fpu: xstate_offset[2]:  576, xstate_sizes[2]:  256
[    0.000000] x86/fpu: xstate_offset[3]:  832, xstate_sizes[3]:   64
[    0.000000] x86/fpu: xstate_offset[4]:  896, xstate_sizes[4]:   64
[    0.000000] x86/fpu: Enabled xstate features 0x1f, context size is 960 bytes, using 'compacted' format.
[    0.000000] BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009dfff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009e000-0x000000000009efff] reserved
[    0.000000] BIOS-e820: [mem 0x000000000009f000-0x000000000009ffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000000a0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000003fffffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000040000000-0x00000000403fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000040400000-0x000000005c5b3fff] usable
[    0.000000] BIOS-e820: [mem 0x000000005c5b4000-0x000000005c5b4fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x000000005c5b5000-0x000000005c5b5fff] reserved
[    0.000000] BIOS-e820: [mem 0x000000005c5b6000-0x000000006c037fff] usable
[    0.000000] BIOS-e820: [mem 0x000000006c038000-0x000000006d7affff] reserved
[    0.000000] BIOS-e820: [mem 0x000000006d7b0000-0x000000006d82cfff] ACPI data
[    0.000000] BIOS-e820: [mem 0x000000006d82d000-0x000000006e1a1fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x000000006e1a2000-0x000000006fe21fff] reserved
[    0.000000] BIOS-e820: [mem 0x000000006fe22000-0x000000006fffefff] type 20
[    0.000000] BIOS-e820: [mem 0x000000006ffff000-0x000000006fffffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000070000000-0x0000000077ffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000078000000-0x0000000078dfffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000078e00000-0x000000007f7fffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000f0000000-0x00000000f7ffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fe000000-0x00000000fe010fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000047c7fffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] efi: EFI v2.70 by American Megatrends
[    0.000000] efi:  ACPI 2.0=0x6d7c9000  ACPI=0x6d7c9000  SMBIOS=0xf0000  SMBIOS 3.0=0xf0020  ESRT=0x6fa68018  MEMATTR=0x69825018 
[    0.000000] SMBIOS 3.2.0 present.
[    0.000000] DMI: Dell Inc. XPS 15 7590/0VYV0G, BIOS 1.1.1 05/31/2019
[    0.000000] tsc: Detected 2600.000 MHz processor
[    0.003481] tsc: Detected 2592.000 MHz TSC
[    0.003481] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.003482] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.003487] last_pfn = 0x47c800 max_arch_pfn = 0x400000000
[    0.003512] MTRR default type: write-back
[    0.003513] MTRR fixed ranges enabled:
[    0.003514]   00000-9FFFF write-back
[    0.003514]   A0000-BFFFF uncachable
[    0.003515]   C0000-FFFFF write-protect
[    0.003515] MTRR variable ranges enabled:
[    0.003516]   0 base 00C0000000 mask 7FC0000000 uncachable
[    0.003517]   1 base 007C000000 mask 7FFC000000 uncachable
[    0.003517]   2 base 007B000000 mask 7FFF000000 uncachable
[    0.003518]   3 base 00A0000000 mask 7FE0000000 uncachable
[    0.003518]   4 base 0090000000 mask 7FF0000000 uncachable
[    0.003519]   5 base 0080000000 mask 7FF0000000 write-combining
[    0.003519]   6 disabled
[    0.003520]   7 disabled
[    0.003520]   8 disabled
[    0.003520]   9 disabled
[    0.004642] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT  
[    0.004829] last_pfn = 0x78e00 max_arch_pfn = 0x400000000
[    0.010030] esrt: Reserving ESRT space from 0x000000006fa68018 to 0x000000006fa68050.
[    0.010036] check: Scanning 1 areas for low memory corruption
[    0.010040] Using GB pages for direct mapping
[    0.010041] BRK [0x10401000, 0x10401fff] PGTABLE
[    0.010042] BRK [0x10402000, 0x10402fff] PGTABLE
[    0.010043] BRK [0x10403000, 0x10403fff] PGTABLE
[    0.010056] BRK [0x10404000, 0x10404fff] PGTABLE
[    0.010057] BRK [0x10405000, 0x10405fff] PGTABLE
[    0.010109] BRK [0x10406000, 0x10406fff] PGTABLE
[    0.010125] BRK [0x10407000, 0x10407fff] PGTABLE
[    0.010164] BRK [0x10408000, 0x10408fff] PGTABLE
[    0.010192] BRK [0x10409000, 0x10409fff] PGTABLE
[    0.010213] Secure boot could not be determined
[    0.010214] RAMDISK: [mem 0x36e4b000-0x3771cfff]
[    0.010222] ACPI: Early table checksum verification disabled
[    0.010224] ACPI: RSDP 0x000000006D7C9000 000024 (v02 DELL  )
[    0.010226] ACPI: XSDT 0x000000006D7C90C8 000114 (v01 DELL   CBX3     01072009 AMI  00010013)
[    0.010229] ACPI: FACP 0x000000006D80A0A8 000114 (v06 DELL   CBX3     01072009 AMI  00010013)
[    0.010232] ACPI: DSDT 0x000000006D7C9270 040E36 (v02 DELL   CBX3     01072009 INTL 20160527)
[    0.010234] ACPI: FACS 0x000000006E1A0C00 000040
[    0.010235] ACPI: APIC 0x000000006D80A1C0 0000F4 (v04 DELL   CBX3     01072009 AMI  00010013)
[    0.010237] ACPI: FPDT 0x000000006D80A2B8 000044 (v01 DELL   CBX3     01072009 AMI  00010013)
[    0.010238] ACPI: FIDT 0x000000006D80A300 00009C (v01 DELL   CBX3     01072009 AMI  00010013)
[    0.010240] ACPI: MCFG 0x000000006D80A3A0 00003C (v01 DELL   CBX3     01072009 MSFT 00000097)
[    0.010241] ACPI: SSDT 0x000000006D80A3E0 001B5F (v02 CpuRef CpuSsdt  00003000 INTL 20160527)
[    0.010243] ACPI: BOOT 0x000000006D80BF40 000028 (v01 DELL   CBX3     01072009 AMI  00010013)
[    0.010245] ACPI: SSDT 0x000000006D80BF68 001663 (v02 SaSsdt SaSsdt   00003000 INTL 20160527)
[    0.010246] ACPI: SSDT 0x000000006D80D5D0 002644 (v02 PegSsd PegSsdt  00001000 INTL 20160527)
[    0.010248] ACPI: HPET 0x000000006D80FC18 000038 (v01 DELL\x CBX3     00000002      01000013)
[    0.010249] ACPI: SSDT 0x000000006D80FC50 001441 (v02 DELL\x CflH_Tbt 00001000 INTL 20160527)
[    0.010251] ACPI: UEFI 0x000000006D811098 000042 (v01 DELL\x CBX3     00000002      01000013)
[    0.010252] ACPI: LPIT 0x000000006D8110E0 000094 (v01 DELL\x CBX3     00000002      01000013)
[    0.010254] ACPI: WSMT 0x000000006D811178 000028 (v01 DELL   CBX3     00000002      01000013)
[    0.010255] ACPI: SSDT 0x000000006D8111A0 0027DE (v02 DELL\x PtidDevc 00001000 INTL 20160527)
[    0.010257] ACPI: SSDT 0x000000006D813980 00037A (v02 DELL\x TbtTypeC 00000000 INTL 20160527)
[    0.010258] ACPI: DBGP 0x000000006D813D00 000034 (v01 DELL\x CBX3     00000002      01000013)
[    0.010260] ACPI: DBG2 0x000000006D813D38 000054 (v00 DELL\x CBX3     00000002      01000013)
[    0.010261] ACPI: SSDT 0x000000006D813D90 0007DC (v02 DELL\x UsbCTabl 00001000 INTL 20160527)
[    0.010263] ACPI: SSDT 0x000000006D814570 00BC5A (v02 DptfTa DptfTabl 00001000 INTL 20160527)
[    0.010264] ACPI: MSDM 0x000000006D8201D0 000055 (v03 DELL   CBX3     06222004 AMI  00010013)
[    0.010266] ACPI: SLIC 0x000000006D820228 000176 (v03 DELL   CBX3     01072009 MSFT 00010013)
[    0.010267] ACPI: DMAR 0x000000006D8203A0 0000C8 (v01 INTEL  EDK2     00000002      01000013)
[    0.010269] ACPI: SSDT 0x000000006D820468 000144 (v02 Intel  ADebTabl 00001000 INTL 20160527)
[    0.010271] ACPI: SSDT 0x000000006D8205B0 0000AE (v02 SgRef  SgPeg    00001000 INTL 20160527)
[    0.010272] ACPI: NHLT 0x000000006D820660 00002D (v00 INTEL  EDK2     00000002      01000013)
[    0.010274] ACPI: BGRT 0x000000006D820690 000038 (v00 DELL   CBX3     01072009 AMI  00010013)
[    0.010275] ACPI: TPM2 0x000000006D8206C8 000034 (v04 DELL\x CBX3     00000001 AMI  00000000)
[    0.010277] ACPI: ASF! 0x000000006D820700 0000A0 (v32 DELL\x CBX3     00000002      01000013)
[    0.010278] ACPI: SSDT 0x000000006D8207A0 001E51 (v01 OptRef OptTabl  00001000 INTL 20160527)
[    0.010283] ACPI: Local APIC address 0xfee00000
[    0.010575] No NUMA configuration found
[    0.010576] Faking a node at [mem 0x0000000000000000-0x000000047c7fffff]
[    0.010578] NODE_DATA(0) allocated [mem 0x47c7fc000-0x47c7fffff]
[    0.010593] Zone ranges:
[    0.010594]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.010594]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
[    0.010595]   Normal   [mem 0x0000000100000000-0x000000047c7fffff]
[    0.010596]   Device   empty
[    0.010596] Movable zone start for each node
[    0.010596] Early memory node ranges
[    0.010597]   node   0: [mem 0x0000000000001000-0x000000000009dfff]
[    0.010597]   node   0: [mem 0x000000000009f000-0x000000000009ffff]
[    0.010598]   node   0: [mem 0x0000000000100000-0x000000003fffffff]
[    0.010598]   node   0: [mem 0x0000000040400000-0x000000005c5b3fff]
[    0.010599]   node   0: [mem 0x000000005c5b6000-0x000000006c037fff]
[    0.010599]   node   0: [mem 0x000000006ffff000-0x000000006fffffff]
[    0.010599]   node   0: [mem 0x0000000078000000-0x0000000078dfffff]
[    0.010600]   node   0: [mem 0x0000000100000000-0x000000047c7fffff]
[    0.010759] Zeroed struct page in unavailable ranges: 46635 pages
[    0.010760] Initmem setup node 0 [mem 0x0000000000001000-0x000000047c7fffff]
[    0.010761] On node 0 totalpages: 4100565
[    0.010762]   DMA zone: 64 pages used for memmap
[    0.010762]   DMA zone: 23 pages reserved
[    0.010763]   DMA zone: 3998 pages, LIFO batch:0
[    0.010793]   DMA32 zone: 6889 pages used for memmap
[    0.010794]   DMA32 zone: 440887 pages, LIFO batch:63
[    0.014694]   Normal zone: 57120 pages used for memmap
[    0.014695]   Normal zone: 3655680 pages, LIFO batch:63
[    0.036795] Reserving Intel graphics memory at [mem 0x7b800000-0x7f7fffff]
[    0.038233] ACPI: PM-Timer IO Port: 0x1808
[    0.038234] ACPI: Local APIC address 0xfee00000
[    0.038238] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.038239] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[    0.038239] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[    0.038240] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[    0.038240] ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
[    0.038240] ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
[    0.038241] ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
[    0.038241] ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1])
[    0.038241] ACPI: LAPIC_NMI (acpi_id[0x09] high edge lint[0x1])
[    0.038242] ACPI: LAPIC_NMI (acpi_id[0x0a] high edge lint[0x1])
[    0.038242] ACPI: LAPIC_NMI (acpi_id[0x0b] high edge lint[0x1])
[    0.038242] ACPI: LAPIC_NMI (acpi_id[0x0c] high edge lint[0x1])
[    0.038307] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-119
[    0.038308] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.038309] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.038310] ACPI: IRQ0 used by override.
[    0.038311] ACPI: IRQ9 used by override.
[    0.038312] Using ACPI (MADT) for SMP configuration information
[    0.038313] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.038316] smpboot: Allowing 12 CPUs, 0 hotplug CPUs
[    0.038335] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.038336] PM: Registered nosave memory: [mem 0x0009e000-0x0009efff]
[    0.038336] PM: Registered nosave memory: [mem 0x000a0000-0x000fffff]
[    0.038337] PM: Registered nosave memory: [mem 0x40000000-0x403fffff]
[    0.038338] PM: Registered nosave memory: [mem 0x5c5b4000-0x5c5b4fff]
[    0.038339] PM: Registered nosave memory: [mem 0x5c5b5000-0x5c5b5fff]
[    0.038340] PM: Registered nosave memory: [mem 0x6c038000-0x6d7affff]
[    0.038340] PM: Registered nosave memory: [mem 0x6d7b0000-0x6d82cfff]
[    0.038340] PM: Registered nosave memory: [mem 0x6d82d000-0x6e1a1fff]
[    0.038341] PM: Registered nosave memory: [mem 0x6e1a2000-0x6fe21fff]
[    0.038341] PM: Registered nosave memory: [mem 0x6fe22000-0x6fffefff]
[    0.038342] PM: Registered nosave memory: [mem 0x70000000-0x77ffffff]
[    0.038343] PM: Registered nosave memory: [mem 0x78e00000-0x7f7fffff]
[    0.038343] PM: Registered nosave memory: [mem 0x7f800000-0xefffffff]
[    0.038344] PM: Registered nosave memory: [mem 0xf0000000-0xf7ffffff]
[    0.038344] PM: Registered nosave memory: [mem 0xf8000000-0xfdffffff]
[    0.038344] PM: Registered nosave memory: [mem 0xfe000000-0xfe010fff]
[    0.038345] PM: Registered nosave memory: [mem 0xfe011000-0xfebfffff]
[    0.038345] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[    0.038345] PM: Registered nosave memory: [mem 0xfec01000-0xfedfffff]
[    0.038346] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[    0.038346] PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
[    0.038346] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
[    0.038348] [mem 0x7f800000-0xefffffff] available for PCI devices
[    0.038348] Booting paravirtualized kernel on bare hardware
[    0.038350] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370452778343963 ns
[    0.097603] setup_percpu: NR_CPUS:320 nr_cpumask_bits:320 nr_cpu_ids:12 nr_node_ids:1
[    0.097832] percpu: Embedded 54 pages/cpu s184320 r8192 d28672 u262144
[    0.097836] pcpu-alloc: s184320 r8192 d28672 u262144 alloc=1*2097152
[    0.097837] pcpu-alloc: [0] 00 01 02 03 04 05 06 07 [0] 08 09 10 11 -- -- -- -- 
[    0.097851] Built 1 zonelists, mobility grouping on.  Total pages: 4036469
[    0.097852] Policy zone: Normal
[    0.097853] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=df4369a4-2b53-4c91-9968-e7e6109ffcb6 rw audit=0 loglevel=3 quiet
[    0.097877] audit: disabled (until reboot)
[    0.100485] Calgary: detecting Calgary via BIOS EBDA area
[    0.100486] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.125641] Memory: 15977984K/16402260K available (12291K kernel code, 1320K rwdata, 3888K rodata, 1608K init, 3632K bss, 424276K reserved, 0K cma-reserved)
[    0.125723] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=12, Nodes=1
[    0.125730] Kernel/User page tables isolation: enabled
[    0.125740] ftrace: allocating 37368 entries in 146 pages
[    0.135214] rcu: Preemptible hierarchical RCU implementation.
[    0.135214] rcu: 	CONFIG_RCU_FANOUT set to non-default value of 32.
[    0.135215] rcu: 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.135215] rcu: 	RCU restricting CPUs from NR_CPUS=320 to nr_cpu_ids=12.
[    0.135216] rcu: 	RCU priority boosting: priority 1 delay 500 ms.
[    0.135217] 	Tasks RCU enabled.
[    0.135218] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    0.135219] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=12
[    0.136295] NR_IRQS: 20736, nr_irqs: 2152, preallocated irqs: 16
[    0.136508] rcu: 	Offload RCU callbacks from CPUs: (none).
[    0.136790] random: get_random_bytes called from start_kernel+0x37e/0x559 with crng_init=0
[    0.136806] Console: colour dummy device 80x25
[    0.136809] printk: console [tty0] enabled
[    0.136820] ACPI: Core revision 20190509
[    0.137250] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635855245 ns
[    0.137320] hpet clockevent registered
[    0.137395] APIC: Switch to symmetric I/O mode setup
[    0.137396] DMAR: Host address width 39
[    0.137397] DMAR: DRHD base: 0x000000fed90000 flags: 0x0
[    0.137400] DMAR: dmar0: reg_base_addr fed90000 ver 1:0 cap 1c0000c40660462 ecap 19e2ff0505e
[    0.137401] DMAR: DRHD base: 0x000000fed91000 flags: 0x1
[    0.137403] DMAR: dmar1: reg_base_addr fed91000 ver 1:0 cap d2008c40660462 ecap f050da
[    0.137404] DMAR: RMRR base: 0x0000006d684000 end: 0x0000006d6a3fff
[    0.137404] DMAR: RMRR base: 0x0000007b000000 end: 0x0000007f7fffff
[    0.137405] DMAR: RMRR base: 0x0000006d730000 end: 0x0000006d7affff
[    0.137406] DMAR-IR: IOAPIC id 2 under DRHD base  0xfed91000 IOMMU 1
[    0.137406] DMAR-IR: HPET id 0 under DRHD base 0xfed91000
[    0.137407] DMAR-IR: Queued invalidation will be enabled to support x2apic and Intr-remapping.
[    0.140483] DMAR-IR: Enabled IRQ remapping in x2apic mode
[    0.140484] x2apic enabled
[    0.140515] Switched APIC routing to cluster x2apic.
[    0.150253] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.164010] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x255cb6cc5db, max_idle_ns: 440795203504 ns
[    0.164013] Calibrating delay loop (skipped), value calculated using timer frequency.. 5186.00 BogoMIPS (lpj=8640000)
[    0.164014] pid_max: default: 32768 minimum: 301
[    0.166133] LSM: Security Framework initializing
[    0.166136] Yama: becoming mindful.
[    0.167595] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[    0.168317] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.168348] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.168369] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.168459] *** VALIDATE proc ***
[    0.168488] *** VALIDATE cgroup1 ***
[    0.168489] *** VALIDATE cgroup2 ***
[    0.168519] mce: CPU0: Thermal monitoring enabled (TM1)
[    0.168534] process: using mwait in idle threads
[    0.168536] Last level iTLB entries: 4KB 64, 2MB 8, 4MB 8
[    0.168536] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0, 1GB 4
[    0.168537] Spectre V2 : Mitigation: Full generic retpoline
[    0.168537] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[    0.168538] Spectre V2 : Enabling Restricted Speculation for firmware calls
[    0.168539] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier
[    0.168539] Spectre V2 : User space: Mitigation: STIBP via seccomp and prctl
[    0.168540] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl and seccomp
[    0.168541] MDS: Vulnerable: Clear CPU buffers attempted, no microcode
[    0.168706] Freeing SMP alternatives memory: 32K
[    0.170615] TSC deadline timer enabled
[    0.170626] smpboot: CPU0: Intel(R) Core(TM) i7-9750H CPU @ 2.60GHz (family: 0x6, model: 0x9e, stepping: 0xa)
[    0.187364] Performance Events: PEBS fmt3+, Skylake events, 32-deep LBR, full-width counters, Intel PMU driver.
[    0.187455] ... version:                4
[    0.187457] ... bit width:              48
[    0.187459] ... generic registers:      4
[    0.187461] ... value mask:             0000ffffffffffff
[    0.187463] ... max period:             00007fffffffffff
[    0.187464] ... fixed-purpose events:   3
[    0.187466] ... event mask:             000000070000000f
[    0.194020] rcu: Hierarchical SRCU implementation.
[    0.217629] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[    0.224035] smp: Bringing up secondary CPUs ...
[    0.264043] x86: Booting SMP configuration:
[    0.264046] .... node  #0, CPUs:        #1  #2  #3  #4  #5  #6
[    0.464583] MDS CPU bug present and SMT on, data leak possible. See https://www.kernel.org/doc/html/latest/admin-guide/hw-vuln/mds.html for more details.
[    0.504047]   #7  #8  #9 #10 #11
[    0.664499] smp: Brought up 1 node, 12 CPUs
[    0.664499] smpboot: Max logical packages: 1
[    0.664499] smpboot: Total of 12 processors activated (62232.00 BogoMIPS)
[    0.667671] devtmpfs: initialized
[    0.667671] x86/mm: Memory block size: 128MB
[    0.668041] PM: Registering ACPI NVS region [mem 0x5c5b4000-0x5c5b4fff] (4096 bytes)
[    0.668041] PM: Registering ACPI NVS region [mem 0x6d82d000-0x6e1a1fff] (9916416 bytes)
[    0.668041] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.668041] futex hash table entries: 4096 (order: 6, 262144 bytes)
[    0.668041] pinctrl core: initialized pinctrl subsystem
[    0.668041] PM: RTC time: 20:22:15, date: 2019-07-12
[    0.668041] NET: Registered protocol family 16
[    0.668041] cpuidle: using governor ladder
[    0.668041] cpuidle: using governor menu
[    0.668041] Simple Boot Flag at 0x47 set to 0x80
[    0.668041] KVM setup pv remote TLB flush
[    0.668041] ACPI: bus type PCI registered
[    0.668041] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.668041] PCI: MMCONFIG for domain 0000 [bus 00-7f] at [mem 0xf0000000-0xf7ffffff] (base 0xf0000000)
[    0.668041] PCI: MMCONFIG at [mem 0xf0000000-0xf7ffffff] reserved in E820
[    0.668041] PCI: Using configuration type 1 for base access
[    0.668041] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[    0.668041] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.668041] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.670747] ACPI: Added _OSI(Module Device)
[    0.670748] ACPI: Added _OSI(Processor Device)
[    0.670748] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.670749] ACPI: Added _OSI(Processor Aggregator Device)
[    0.670749] ACPI: Added _OSI(Linux-Dell-Video)
[    0.670750] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[    0.670750] ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics)
[    0.712542] ACPI: 12 ACPI AML tables successfully acquired and loaded
[    0.773211] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[    0.786409] ACPI: Dynamic OEM Table Load:
[    0.786414] ACPI: SSDT 0xFFFF8B6929208900 0000F4 (v02 PmRef  Cpu0Psd  00003000 INTL 20160527)
[    0.786911] ACPI: \_SB_.PR00: _OSC native thermal LVT Acked
[    0.788051] ACPI: Dynamic OEM Table Load:
[    0.788056] ACPI: SSDT 0xFFFF8B69291CE000 000400 (v02 PmRef  Cpu0Cst  00003001 INTL 20160527)
[    0.788686] ACPI: Dynamic OEM Table Load:
[    0.788691] ACPI: SSDT 0xFFFF8B6929853800 000581 (v02 PmRef  Cpu0Ist  00003000 INTL 20160527)
[    0.789409] ACPI: Dynamic OEM Table Load:
[    0.789413] ACPI: SSDT 0xFFFF8B6929769600 000149 (v02 PmRef  Cpu0Hwp  00003000 INTL 20160527)
[    0.789935] ACPI: Dynamic OEM Table Load:
[    0.789941] ACPI: SSDT 0xFFFF8B6929854800 000724 (v02 PmRef  HwpLvt   00003000 INTL 20160527)
[    0.790739] ACPI: Dynamic OEM Table Load:
[    0.790743] ACPI: SSDT 0xFFFF8B6929853000 0005FC (v02 PmRef  ApIst    00003000 INTL 20160527)
[    0.791355] ACPI: Dynamic OEM Table Load:
[    0.791359] ACPI: SSDT 0xFFFF8B69291C9000 000317 (v02 PmRef  ApHwp    00003000 INTL 20160527)
[    0.791989] ACPI: Dynamic OEM Table Load:
[    0.791993] ACPI: SSDT 0xFFFF8B69295BE000 000AB0 (v02 PmRef  ApPsd    00003000 INTL 20160527)
[    0.793147] ACPI: Dynamic OEM Table Load:
[    0.793152] ACPI: SSDT 0xFFFF8B69291CE400 00030A (v02 PmRef  ApCst    00003000 INTL 20160527)
[    0.797912] ACPI: EC: EC started
[    0.797913] ACPI: EC: interrupt blocked
[    0.806038] ACPI: \_SB_.PCI0.LPCB.ECDV: Used as first EC
[    0.806040] ACPI: \_SB_.PCI0.LPCB.ECDV: GPE=0x6e, EC_CMD/EC_SC=0x934, EC_DATA=0x930
[    0.806040] ACPI: \_SB_.PCI0.LPCB.ECDV: Boot DSDT EC used to handle transactions
[    0.806041] ACPI: Interpreter enabled
[    0.806077] ACPI: (supports S0 S3 S4 S5)
[    0.806078] ACPI: Using IOAPIC for interrupt routing
[    0.806113] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.806643] ACPI: Enabled 10 GPEs in block 00 to 7F
[    0.808770] ACPI: Power Resource [PG00] (on)
[    0.812151] ACPI: Power Resource [WRST] (on)
[    0.812189] ACPI: Power Resource [DRST] (on)
[    0.816068] ACPI: Power Resource [PXP] (on)
[    0.820827] ACPI: Power Resource [USBC] (on)
[    0.823484] ACPI: Power Resource [V0PR] (on)
[    0.823622] ACPI: Power Resource [V1PR] (on)
[    0.823755] ACPI: Power Resource [V2PR] (on)
[    0.828399] ACPI: Power Resource [WRST] (on)
[    0.836316] ACPI: Power Resource [PIN] (off)
[    0.836671] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7e])
[    0.836676] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3]
[    0.838300] acpi PNP0A08:00: _OSC: platform does not support [AER]
[    0.841373] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug SHPCHotplug PME PCIeCapability LTR]
[    0.842180] PCI host bridge to bus 0000:00
[    0.842182] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.842182] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.842183] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.842184] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000c3fff window]
[    0.842184] pci_bus 0000:00: root bus resource [mem 0x000c4000-0x000c7fff window]
[    0.842185] pci_bus 0000:00: root bus resource [mem 0x000c8000-0x000cbfff window]
[    0.842185] pci_bus 0000:00: root bus resource [mem 0x000cc000-0x000cffff window]
[    0.842186] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff window]
[    0.842187] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff window]
[    0.842187] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff window]
[    0.842188] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff window]
[    0.842188] pci_bus 0000:00: root bus resource [mem 0x7f800000-0xefffffff window]
[    0.842189] pci_bus 0000:00: root bus resource [mem 0xfc800000-0xfe7fffff window]
[    0.842190] pci_bus 0000:00: root bus resource [bus 00-7e]
[    0.842195] pci 0000:00:00.0: [8086:3ec4] type 00 class 0x060000
[    0.842297] pci 0000:00:01.0: [8086:1901] type 01 class 0x060400
[    0.842330] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.842531] pci 0000:00:02.0: [8086:3e9b] type 00 class 0x030000
[    0.842538] pci 0000:00:02.0: reg 0x10: [mem 0xeb000000-0xebffffff 64bit]
[    0.842541] pci 0000:00:02.0: reg 0x18: [mem 0x80000000-0x8fffffff 64bit pref]
[    0.842544] pci 0000:00:02.0: reg 0x20: [io  0x4000-0x403f]
[    0.842554] pci 0000:00:02.0: BAR 2: assigned to efifb
[    0.842659] pci 0000:00:04.0: [8086:1903] type 00 class 0x118000
[    0.842667] pci 0000:00:04.0: reg 0x10: [mem 0xed510000-0xed517fff 64bit]
[    0.842817] pci 0000:00:08.0: [8086:1911] type 00 class 0x088000
[    0.842824] pci 0000:00:08.0: reg 0x10: [mem 0xed528000-0xed528fff 64bit]
[    0.843020] pci 0000:00:12.0: [8086:a379] type 00 class 0x118000
[    0.843061] pci 0000:00:12.0: reg 0x10: [mem 0xed527000-0xed527fff 64bit]
[    0.843363] pci 0000:00:14.0: [8086:a36d] type 00 class 0x0c0330
[    0.843406] pci 0000:00:14.0: reg 0x10: [mem 0xed500000-0xed50ffff 64bit]
[    0.843539] pci 0000:00:14.0: PME# supported from D3hot D3cold
[    0.843688] pci 0000:00:14.2: [8086:a36f] type 00 class 0x050000
[    0.843722] pci 0000:00:14.2: reg 0x10: [mem 0xed51e000-0xed51ffff 64bit]
[    0.843740] pci 0000:00:14.2: reg 0x18: [mem 0xed526000-0xed526fff 64bit]
[    0.844164] pci 0000:00:15.0: [8086:a368] type 00 class 0x0c8000
[    0.844893] pci 0000:00:15.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit]
[    0.847574] pci 0000:00:15.1: [8086:a369] type 00 class 0x0c8000
[    0.848302] pci 0000:00:15.1: reg 0x10: [mem 0x00000000-0x00000fff 64bit]
[    0.850774] pci 0000:00:16.0: [8086:a360] type 00 class 0x078000
[    0.850814] pci 0000:00:16.0: reg 0x10: [mem 0xed523000-0xed523fff 64bit]
[    0.850928] pci 0000:00:16.0: PME# supported from D3hot
[    0.851159] pci 0000:00:17.0: [8086:a353] type 00 class 0x010601
[    0.851223] pci 0000:00:17.0: reg 0x10: [mem 0xed51c000-0xed51dfff]
[    0.851248] pci 0000:00:17.0: reg 0x14: [mem 0xed522000-0xed5220ff]
[    0.851271] pci 0000:00:17.0: reg 0x18: [io  0x4090-0x4097]
[    0.851294] pci 0000:00:17.0: reg 0x1c: [io  0x4080-0x4083]
[    0.851317] pci 0000:00:17.0: reg 0x20: [io  0x4060-0x407f]
[    0.851339] pci 0000:00:17.0: reg 0x24: [mem 0xed521000-0xed5217ff]
[    0.851477] pci 0000:00:17.0: PME# supported from D3hot
[    0.851676] pci 0000:00:1b.0: [8086:a340] type 01 class 0x060400
[    0.851916] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.851948] pci 0000:00:1b.0: PTM enabled (root), 4dns granularity
[    0.852186] pci 0000:00:1c.0: [8086:a338] type 01 class 0x060400
[    0.852385] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.852415] pci 0000:00:1c.0: PTM enabled (root), 4dns granularity
[    0.852607] pci 0000:00:1c.4: [8086:a33c] type 01 class 0x060400
[    0.852795] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[    0.852824] pci 0000:00:1c.4: PTM enabled (root), 4dns granularity
[    0.853019] pci 0000:00:1d.0: [8086:a330] type 01 class 0x060400
[    0.853206] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    0.853238] pci 0000:00:1d.0: PTM enabled (root), 4dns granularity
[    0.853474] pci 0000:00:1f.0: [8086:a30e] type 00 class 0x060100
[    0.853745] pci 0000:00:1f.3: [8086:a348] type 00 class 0x040380
[    0.853823] pci 0000:00:1f.3: reg 0x10: [mem 0xed518000-0xed51bfff 64bit]
[    0.853896] pci 0000:00:1f.3: reg 0x20: [mem 0xed100000-0xed1fffff 64bit]
[    0.854044] pci 0000:00:1f.3: PME# supported from D3hot D3cold
[    0.854278] pci 0000:00:1f.4: [8086:a323] type 00 class 0x0c0500
[    0.854431] pci 0000:00:1f.4: reg 0x10: [mem 0xed520000-0xed5200ff 64bit]
[    0.854601] pci 0000:00:1f.4: reg 0x20: [io  0xefa0-0xefbf]
[    0.854912] pci 0000:00:1f.5: [8086:a324] type 00 class 0x0c8000
[    0.854938] pci 0000:00:1f.5: reg 0x10: [mem 0xfe010000-0xfe010fff]
[    0.855153] pci 0000:01:00.0: [10de:1f91] type 00 class 0x030200
[    0.855179] pci 0000:01:00.0: reg 0x10: [mem 0xec000000-0xecffffff]
[    0.855193] pci 0000:01:00.0: reg 0x14: [mem 0xc0000000-0xcfffffff 64bit pref]
[    0.855207] pci 0000:01:00.0: reg 0x1c: [mem 0xd0000000-0xd1ffffff 64bit pref]
[    0.855215] pci 0000:01:00.0: reg 0x24: [io  0x3000-0x307f]
[    0.855223] pci 0000:01:00.0: reg 0x30: [mem 0xed000000-0xed07ffff pref]
[    0.855296] pci 0000:01:00.0: PME# supported from D0 D3hot
[    0.855414] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.855416] pci 0000:00:01.0:   bridge window [io  0x3000-0x3fff]
[    0.855417] pci 0000:00:01.0:   bridge window [mem 0xec000000-0xed0fffff]
[    0.855419] pci 0000:00:01.0:   bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
[    0.855579] pci 0000:02:00.0: [8086:15da] type 01 class 0x060400
[    0.855682] pci 0000:02:00.0: enabling Extended Tags
[    0.855816] pci 0000:02:00.0: supports D1 D2
[    0.855817] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.855979] pci 0000:00:1b.0: PCI bridge to [bus 02-3a]
[    0.855988] pci 0000:00:1b.0:   bridge window [mem 0xd4000000-0xea0fffff]
[    0.855996] pci 0000:00:1b.0:   bridge window [mem 0x90000000-0xb1ffffff 64bit pref]
[    0.856081] pci 0000:03:00.0: [8086:15da] type 01 class 0x060400
[    0.856187] pci 0000:03:00.0: enabling Extended Tags
[    0.856324] pci 0000:03:00.0: supports D1 D2
[    0.856325] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.856447] pci 0000:03:01.0: [8086:15da] type 01 class 0x060400
[    0.856553] pci 0000:03:01.0: enabling Extended Tags
[    0.856691] pci 0000:03:01.0: supports D1 D2
[    0.856692] pci 0000:03:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.856815] pci 0000:03:02.0: [8086:15da] type 01 class 0x060400
[    0.856921] pci 0000:03:02.0: enabling Extended Tags
[    0.857054] pci 0000:03:02.0: supports D1 D2
[    0.857055] pci 0000:03:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.857215] pci 0000:02:00.0: PCI bridge to [bus 03-3a]
[    0.857228] pci 0000:02:00.0:   bridge window [mem 0xd4000000-0xea0fffff]
[    0.857236] pci 0000:02:00.0:   bridge window [mem 0x90000000-0xb1ffffff 64bit pref]
[    0.857307] pci 0000:04:00.0: [8086:15d9] type 00 class 0x088000
[    0.857351] pci 0000:04:00.0: reg 0x10: [mem 0xea000000-0xea03ffff]
[    0.857366] pci 0000:04:00.0: reg 0x14: [mem 0xea040000-0xea040fff]
[    0.857447] pci 0000:04:00.0: enabling Extended Tags
[    0.857586] pci 0000:04:00.0: supports D1 D2
[    0.857587] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.857783] pci 0000:03:00.0: PCI bridge to [bus 04]
[    0.857795] pci 0000:03:00.0:   bridge window [mem 0xea000000-0xea0fffff]
[    0.857858] pci 0000:03:01.0: PCI bridge to [bus 05-39]
[    0.857870] pci 0000:03:01.0:   bridge window [mem 0xd4000000-0xe9efffff]
[    0.857878] pci 0000:03:01.0:   bridge window [mem 0x90000000-0xb1ffffff 64bit pref]
[    0.857964] pci 0000:3a:00.0: [8086:15db] type 00 class 0x0c0330
[    0.858010] pci 0000:3a:00.0: reg 0x10: [mem 0xe9f00000-0xe9f0ffff]
[    0.858110] pci 0000:3a:00.0: enabling Extended Tags
[    0.858252] pci 0000:3a:00.0: supports D1 D2
[    0.858252] pci 0000:3a:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.858344] pci 0000:3a:00.0: 8.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x4 link at 0000:03:02.0 (capable of 31.504 Gb/s with 8 GT/s x4 link)
[    0.858466] pci 0000:03:02.0: PCI bridge to [bus 3a]
[    0.858479] pci 0000:03:02.0:   bridge window [mem 0xe9f00000-0xe9ffffff]
[    0.859302] pci 0000:3b:00.0: [8086:2723] type 00 class 0x028000
[    0.860013] pci 0000:3b:00.0: reg 0x10: [mem 0xed400000-0xed403fff 64bit]
[    0.862768] pci 0000:3b:00.0: PME# supported from D0 D3hot D3cold
[    0.864670] pci 0000:00:1c.0: PCI bridge to [bus 3b]
[    0.864679] pci 0000:00:1c.0:   bridge window [mem 0xed400000-0xed4fffff]
[    0.864848] pci 0000:3c:00.0: [10ec:525a] type 00 class 0xff0000
[    0.864894] pci 0000:3c:00.0: reg 0x14: [mem 0xed300000-0xed300fff]
[    0.865051] pci 0000:3c:00.0: supports D1 D2
[    0.865052] pci 0000:3c:00.0: PME# supported from D1 D2 D3hot D3cold
[    0.865228] pci 0000:00:1c.4: PCI bridge to [bus 3c]
[    0.865236] pci 0000:00:1c.4:   bridge window [mem 0xed300000-0xed3fffff]
[    0.865394] pci 0000:3d:00.0: [1179:011a] type 00 class 0x010802
[    0.865441] pci 0000:3d:00.0: reg 0x10: [mem 0xed200000-0xed203fff 64bit]
[    0.865775] pci 0000:00:1d.0: PCI bridge to [bus 3d]
[    0.865783] pci 0000:00:1d.0:   bridge window [mem 0xed200000-0xed2fffff]
[    0.868088] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 11 12 14 15) *0
[    0.868157] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15) *1
[    0.868225] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 11 12 14 15) *0
[    0.868292] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 11 12 14 15) *0
[    0.868359] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0
[    0.868426] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0
[    0.868493] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 11 12 14 15) *0
[    0.868560] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 11 12 14 15) *0
[    0.881882] ACPI: EC: interrupt unblocked
[    0.881909] ACPI: EC: event unblocked
[    0.881953] ACPI: \_SB_.PCI0.LPCB.ECDV: GPE=0x6e, EC_CMD/EC_SC=0x934, EC_DATA=0x930
[    0.881954] ACPI: \_SB_.PCI0.LPCB.ECDV: Boot DSDT EC used to handle transactions and events
[    0.882032] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[    0.882032] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[    0.882032] pci 0000:00:02.0: vgaarb: bridge control possible
[    0.882032] vgaarb: loaded
[    0.882032] ACPI: bus type USB registered
[    0.882032] usbcore: registered new interface driver usbfs
[    0.882032] usbcore: registered new interface driver hub
[    0.882032] usbcore: registered new device driver usb
[    0.882032] pps_core: LinuxPPS API ver. 1 registered
[    0.882032] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.882032] PTP clock support registered
[    0.882032] EDAC MC: Ver: 3.0.0
[    0.882032] Registered efivars operations
[    0.940718] PCI: Using ACPI for IRQ routing
[    0.966433] PCI: pci_cache_line_size set to 64 bytes
[    0.966979] e820: reserve RAM buffer [mem 0x0009e000-0x0009ffff]
[    0.966980] e820: reserve RAM buffer [mem 0x5c5b4000-0x5fffffff]
[    0.966980] e820: reserve RAM buffer [mem 0x6c038000-0x6fffffff]
[    0.966981] e820: reserve RAM buffer [mem 0x78e00000-0x7bffffff]
[    0.966981] e820: reserve RAM buffer [mem 0x47c800000-0x47fffffff]
[    0.967042] NetLabel: Initializing
[    0.967042] NetLabel:  domain hash size = 128
[    0.967043] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.967051] NetLabel:  unlabeled traffic allowed by default
[    0.967053] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[    0.967053] hpet0: 8 comparators, 64-bit 24.000000 MHz counter
[    0.969431] clocksource: Switched to clocksource tsc-early
[    0.974179] VFS: Disk quotas dquot_6.6.0
[    0.974192] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.974205] *** VALIDATE hugetlbfs ***
[    0.974227] pnp: PnP ACPI init
[    0.974302] system 00:00: [mem 0x40000000-0x403fffff] has been reserved
[    0.974305] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.974443] system 00:01: [io  0x0680-0x069f] has been reserved
[    0.974444] system 00:01: [io  0x164e-0x164f] has been reserved
[    0.974446] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.974480] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.974556] system 00:03: [io  0x1854-0x1857] has been reserved
[    0.974558] system 00:03: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[    0.974661] pnp 00:04: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.974672] pnp 00:05: Plug and Play ACPI device, IDs DLL0905 PNP0f13 (active)
[    0.974821] system 00:06: [mem 0xfed10000-0xfed17fff] has been reserved
[    0.974822] system 00:06: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.974823] system 00:06: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.974824] system 00:06: [mem 0xf0000000-0xf7ffffff] has been reserved
[    0.974824] system 00:06: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.974825] system 00:06: [mem 0xfed90000-0xfed93fff] could not be reserved
[    0.974826] system 00:06: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.974827] system 00:06: [mem 0xfee00000-0xfeefffff] could not be reserved
[    0.974828] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.975017] system 00:07: [io  0x1800-0x18fe] could not be reserved
[    0.975018] system 00:07: [mem 0xfd000000-0xfd69ffff] has been reserved
[    0.975018] system 00:07: [mem 0xfd6c0000-0xfd6cffff] has been reserved
[    0.975019] system 00:07: [mem 0xfd6f0000-0xfdffffff] has been reserved
[    0.975020] system 00:07: [mem 0xfe000000-0xfe01ffff] could not be reserved
[    0.975021] system 00:07: [mem 0xfe200000-0xfe7fffff] has been reserved
[    0.975021] system 00:07: [mem 0xff000000-0xffffffff] has been reserved
[    0.975023] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.975275] system 00:08: [io  0x2000-0x20fe] has been reserved
[    0.975277] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.976168] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.983535] pnp: PnP ACPI: found 10 devices
[    0.988747] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.988752] pci 0000:03:01.0: bridge window [io  0x1000-0x0fff] to [bus 05-39] add_size 1000
[    0.988754] pci 0000:02:00.0: bridge window [io  0x1000-0x0fff] to [bus 03-3a] add_size 1000
[    0.988755] pci 0000:00:1b.0: bridge window [io  0x1000-0x0fff] to [bus 02-3a] add_size 2000
[    0.988762] pci 0000:00:15.0: BAR 0: assigned [mem 0x7f800000-0x7f800fff 64bit]
[    0.989033] pci 0000:00:15.1: BAR 0: assigned [mem 0x7f801000-0x7f801fff 64bit]
[    0.989300] pci 0000:00:1b.0: BAR 13: assigned [io  0x5000-0x6fff]
[    0.989302] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.989303] pci 0000:00:01.0:   bridge window [io  0x3000-0x3fff]
[    0.989305] pci 0000:00:01.0:   bridge window [mem 0xec000000-0xed0fffff]
[    0.989306] pci 0000:00:01.0:   bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
[    0.989309] pci 0000:02:00.0: BAR 13: assigned [io  0x5000-0x5fff]
[    0.989310] pci 0000:03:01.0: BAR 13: assigned [io  0x5000-0x5fff]
[    0.989311] pci 0000:03:00.0: PCI bridge to [bus 04]
[    0.989321] pci 0000:03:00.0:   bridge window [mem 0xea000000-0xea0fffff]
[    0.989333] pci 0000:03:01.0: PCI bridge to [bus 05-39]
[    0.989335] pci 0000:03:01.0:   bridge window [io  0x5000-0x5fff]
[    0.989342] pci 0000:03:01.0:   bridge window [mem 0xd4000000-0xe9efffff]
[    0.989346] pci 0000:03:01.0:   bridge window [mem 0x90000000-0xb1ffffff 64bit pref]
[    0.989355] pci 0000:03:02.0: PCI bridge to [bus 3a]
[    0.989361] pci 0000:03:02.0:   bridge window [mem 0xe9f00000-0xe9ffffff]
[    0.989373] pci 0000:02:00.0: PCI bridge to [bus 03-3a]
[    0.989376] pci 0000:02:00.0:   bridge window [io  0x5000-0x5fff]
[    0.989382] pci 0000:02:00.0:   bridge window [mem 0xd4000000-0xea0fffff]
[    0.989387] pci 0000:02:00.0:   bridge window [mem 0x90000000-0xb1ffffff 64bit pref]
[    0.989394] pci 0000:00:1b.0: PCI bridge to [bus 02-3a]
[    0.989397] pci 0000:00:1b.0:   bridge window [io  0x5000-0x6fff]
[    0.989403] pci 0000:00:1b.0:   bridge window [mem 0xd4000000-0xea0fffff]
[    0.989408] pci 0000:00:1b.0:   bridge window [mem 0x90000000-0xb1ffffff 64bit pref]
[    0.989416] pci 0000:00:1c.0: PCI bridge to [bus 3b]
[    0.989424] pci 0000:00:1c.0:   bridge window [mem 0xed400000-0xed4fffff]
[    0.989436] pci 0000:00:1c.4: PCI bridge to [bus 3c]
[    0.989443] pci 0000:00:1c.4:   bridge window [mem 0xed300000-0xed3fffff]
[    0.989455] pci 0000:00:1d.0: PCI bridge to [bus 3d]
[    0.989461] pci 0000:00:1d.0:   bridge window [mem 0xed200000-0xed2fffff]
[    0.989474] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.989475] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.989475] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.989476] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff window]
[    0.989476] pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff window]
[    0.989477] pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff window]
[    0.989478] pci_bus 0000:00: resource 10 [mem 0x000cc000-0x000cffff window]
[    0.989478] pci_bus 0000:00: resource 11 [mem 0x000d0000-0x000d3fff window]
[    0.989479] pci_bus 0000:00: resource 12 [mem 0x000d4000-0x000d7fff window]
[    0.989479] pci_bus 0000:00: resource 13 [mem 0x000d8000-0x000dbfff window]
[    0.989480] pci_bus 0000:00: resource 14 [mem 0x000dc000-0x000dffff window]
[    0.989481] pci_bus 0000:00: resource 15 [mem 0x7f800000-0xefffffff window]
[    0.989481] pci_bus 0000:00: resource 16 [mem 0xfc800000-0xfe7fffff window]
[    0.989482] pci_bus 0000:01: resource 0 [io  0x3000-0x3fff]
[    0.989483] pci_bus 0000:01: resource 1 [mem 0xec000000-0xed0fffff]
[    0.989483] pci_bus 0000:01: resource 2 [mem 0xc0000000-0xd1ffffff 64bit pref]
[    0.989484] pci_bus 0000:02: resource 0 [io  0x5000-0x6fff]
[    0.989484] pci_bus 0000:02: resource 1 [mem 0xd4000000-0xea0fffff]
[    0.989485] pci_bus 0000:02: resource 2 [mem 0x90000000-0xb1ffffff 64bit pref]
[    0.989486] pci_bus 0000:03: resource 0 [io  0x5000-0x5fff]
[    0.989486] pci_bus 0000:03: resource 1 [mem 0xd4000000-0xea0fffff]
[    0.989487] pci_bus 0000:03: resource 2 [mem 0x90000000-0xb1ffffff 64bit pref]
[    0.989487] pci_bus 0000:04: resource 1 [mem 0xea000000-0xea0fffff]
[    0.989488] pci_bus 0000:05: resource 0 [io  0x5000-0x5fff]
[    0.989489] pci_bus 0000:05: resource 1 [mem 0xd4000000-0xe9efffff]
[    0.989489] pci_bus 0000:05: resource 2 [mem 0x90000000-0xb1ffffff 64bit pref]
[    0.989490] pci_bus 0000:3a: resource 1 [mem 0xe9f00000-0xe9ffffff]
[    0.989490] pci_bus 0000:3b: resource 1 [mem 0xed400000-0xed4fffff]
[    0.989491] pci_bus 0000:3c: resource 1 [mem 0xed300000-0xed3fffff]
[    0.989492] pci_bus 0000:3d: resource 1 [mem 0xed200000-0xed2fffff]
[    0.989614] NET: Registered protocol family 2
[    0.989693] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes)
[    0.989726] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.989832] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.989908] TCP: Hash tables configured (established 131072 bind 65536)
[    0.989932] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[    0.989956] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[    0.990018] NET: Registered protocol family 1
[    0.990021] NET: Registered protocol family 44
[    0.990027] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.990391] pci 0000:02:00.0: CLS mismatch (64 != 128), using 64 bytes
[    0.990489] pci 0000:02:00.0: enabling device (0006 -> 0007)
[    0.990711] Trying to unpack rootfs image as initramfs...
[    1.069957] Freeing initrd memory: 9032K
[    1.094095] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    1.094097] software IO TLB: mapped [mem 0x63203000-0x67203000] (64MB)
[    1.094134] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x255cb6cc5db, max_idle_ns: 440795203504 ns
[    1.094152] clocksource: Switched to clocksource tsc
[    1.094288] check: Scanning for low memory corruption every 60 seconds
[    1.094868] Initialise system trusted keyrings
[    1.094876] Key type blacklist registered
[    1.094901] workingset: timestamp_bits=41 max_order=22 bucket_order=0
[    1.095948] zbud: loaded
[    1.097354] Key type asymmetric registered
[    1.097355] Asymmetric key parser 'x509' registered
[    1.097362] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[    1.097413] io scheduler mq-deadline registered
[    1.097414] io scheduler kyber registered
[    1.097458] io scheduler bfq registered
[    1.101788] pcieport 0000:00:01.0: PME: Signaling with IRQ 122
[    1.101917] pcieport 0000:00:1b.0: PME: Signaling with IRQ 123
[    1.101950] pcieport 0000:00:1b.0: pciehp: Slot #20 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Interlock- NoCompl+ LLActRep+
[    1.102309] pcieport 0000:00:1c.0: PME: Signaling with IRQ 124
[    1.102636] pcieport 0000:00:1c.4: PME: Signaling with IRQ 125
[    1.102956] pcieport 0000:00:1d.0: PME: Signaling with IRQ 126
[    1.103432] pcieport 0000:03:01.0: enabling device (0006 -> 0007)
[    1.103548] pcieport 0000:03:01.0: pciehp: Slot #1 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Interlock- NoCompl+ LLActRep+
[    1.103881] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    1.103938] efifb: probing for efifb
[    1.103951] efifb: showing boot graphics
[    1.105653] efifb: framebuffer at 0x80000000, using 32448k, total 32448k
[    1.105654] efifb: mode is 3840x2160x32, linelength=15360, pages=1
[    1.105654] efifb: scrolling: redraw
[    1.105655] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    1.105676] fbcon: Deferring console take-over
[    1.105677] fb0: EFI VGA frame buffer device
[    1.105681] intel_idle: MWAIT substates: 0x11142120
[    1.105681] intel_idle: v0.4.1 model 0x9E
[    1.106096] intel_idle: lapic_timer_reliable_states 0xffffffff
[    1.106185] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[    1.107387] ACPI: Lid Switch [LID0]
[    1.107422] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[    1.107508] ACPI: Power Button [PBTN]
[    1.107524] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[    1.107540] ACPI: Sleep Button [SBTN]
[    1.110201] thermal LNXTHERM:00: registered as thermal_zone0
[    1.110202] ACPI: Thermal Zone [THM] (25 C)
[    1.110418] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.112146] nvme nvme0: pci function 0000:3d:00.0
[    1.112160] usbcore: registered new interface driver usbserial_generic
[    1.112176] usbserial: USB Serial support registered for generic
[    1.112242] rtc_cmos 00:02: RTC can wake from S4
[    1.113349] rtc_cmos 00:02: registered as rtc0
[    1.113356] rtc_cmos 00:02: alarms up to one month, y3k, 242 bytes nvram
[    1.113404] intel_pstate: Intel P-state driver initializing
[    1.113443] intel_pstate: Disabling energy efficiency optimization
[    1.114269] intel_pstate: HWP enabled
[    1.114810] ledtrig-cpu: registered to indicate activity on CPUs
[    1.114872] intel_pmc_core intel_pmc_core.0:  initialized
[    1.115053] NET: Registered protocol family 10
[    1.120297] Segment Routing with IPv6
[    1.120309] NET: Registered protocol family 17
[    1.121281] mce: Using 12 MCE banks
[    1.121290] RAS: Correctable Errors collector initialized.
[    1.121352] microcode: sig=0x906ea, pf=0x20, revision=0xaa
[    1.121721] microcode: Microcode Update Driver: v2.2.
[    1.121727] sched_clock: Marking stable (1124456607, -2736861)->(1144606756, -22887010)
[    1.122180] registered taskstats version 1
[    1.122183] Loading compiled-in X.509 certificates
[    1.124867] Loaded X.509 cert 'Build time autogenerated kernel key: 07dd371a413a09c89d871775aff3f9b6d725cdd4'
[    1.124883] zswap: loaded using pool lzo/zbud
[    1.129462] Key type big_key registered
[    1.130445] PM:   Magic number: 11:851:396
[    1.130800] rtc_cmos 00:02: setting system clock to 2019-07-12T20:22:15 UTC (1562962935)
[    1.335806] nvme nvme0: 12/0/0 default/read/poll queues
[    1.340705]  nvme0n1: p1 p2 p3 p4
[    1.344481] Freeing unused decrypted memory: 2040K
[    1.345143] Freeing unused kernel image memory: 1608K
[    1.374389] Write protecting the kernel read-only data: 18432k
[    1.375619] Freeing unused kernel image memory: 2012K
[    1.375981] Freeing unused kernel image memory: 208K
[    1.384360] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    1.384361] x86/mm: Checking user space page tables
[    1.389329] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    1.389330] Run /init as init process
[    1.536571] fbcon: Taking over console
[    1.536617] Console: switching to colour frame buffer device 480x135
[    1.584410] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    1.584917] i8042: Warning: Keylock active
[    1.586790] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.586818] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.590325] SCSI subsystem initialized
[    1.590439] rtsx_pci 0000:3c:00.0: enabling device (0000 -> 0002)
[    1.592937] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    1.592942] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[    1.594046] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x110 quirks 0x0000000000009810
[    1.594054] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[    1.594206] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[    1.594207] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.594208] usb usb1: Product: xHCI Host Controller
[    1.594209] usb usb1: Manufacturer: Linux 5.2.0-arch2-1-ARCH xhci-hcd
[    1.594209] usb usb1: SerialNumber: 0000:00:14.0
[    1.594281] hub 1-0:1.0: USB hub found
[    1.594299] hub 1-0:1.0: 16 ports detected
[    1.595531] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    1.595533] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[    1.595537] xhci_hcd 0000:00:14.0: Host supports USB 3.0 SuperSpeed
[    1.595565] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.02
[    1.595566] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.595567] usb usb2: Product: xHCI Host Controller
[    1.595568] usb usb2: Manufacturer: Linux 5.2.0-arch2-1-ARCH xhci-hcd
[    1.595568] usb usb2: SerialNumber: 0000:00:14.0
[    1.595596] libata version 3.00 loaded.
[    1.595636] hub 2-0:1.0: USB hub found
[    1.595651] hub 2-0:1.0: 10 ports detected
[    1.596017] usb: port power management may be unreliable
[    1.596712] xhci_hcd 0000:3a:00.0: xHCI Host Controller
[    1.596716] xhci_hcd 0000:3a:00.0: new USB bus registered, assigned bus number 3
[    1.597657] ahci 0000:00:17.0: version 3.0
[    1.597915] xhci_hcd 0000:3a:00.0: hcc params 0x200077c1 hci version 0x110 quirks 0x0000000200009810
[    1.598002] ahci 0000:00:17.0: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x4 impl SATA mode
[    1.598003] ahci 0000:00:17.0: flags: 64bit ncq sntf pm clo only pio slum part ems deso sadm sds apst 
[    1.598200] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[    1.598202] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.598203] usb usb3: Product: xHCI Host Controller
[    1.598204] usb usb3: Manufacturer: Linux 5.2.0-arch2-1-ARCH xhci-hcd
[    1.598205] usb usb3: SerialNumber: 0000:3a:00.0
[    1.598301] hub 3-0:1.0: USB hub found
[    1.598315] hub 3-0:1.0: 2 ports detected
[    1.598739] xhci_hcd 0000:3a:00.0: xHCI Host Controller
[    1.598742] xhci_hcd 0000:3a:00.0: new USB bus registered, assigned bus number 4
[    1.598745] xhci_hcd 0000:3a:00.0: Host supports USB 3.0 SuperSpeed
[    1.598778] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.02
[    1.598779] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.598780] usb usb4: Product: xHCI Host Controller
[    1.598780] usb usb4: Manufacturer: Linux 5.2.0-arch2-1-ARCH xhci-hcd
[    1.598781] usb usb4: SerialNumber: 0000:3a:00.0
[    1.598845] hub 4-0:1.0: USB hub found
[    1.598858] hub 4-0:1.0: 2 ports detected
[    1.599715] scsi host0: ahci
[    1.599935] scsi host1: ahci
[    1.599999] scsi host2: ahci
[    1.600032] ata1: DUMMY
[    1.600032] ata2: DUMMY
[    1.600045] ata3: SATA max UDMA/133 abar m2048@0xed521000 port 0xed521200 irq 145
[    1.600828] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[    1.913019] ata3: SATA link down (SStatus 4 SControl 300)
[    1.924336] usb 1-4: new full-speed USB device number 2 using xhci_hcd
[    1.980808] EXT4-fs (nvme0n1p2): mounted filesystem with ordered data mode. Opts: (null)
[    1.991819] random: fast init done
[    2.043150] systemd[1]: systemd 242.32-3-arch running in system mode. (+PAM +AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
[    2.057847] systemd[1]: Detected architecture x86-64.
[    2.066695] systemd[1]: Set hostname to <creator>.
[    2.068773] usb 1-4: New USB device found, idVendor=8087, idProduct=0029, bcdDevice= 0.01
[    2.068774] usb 1-4: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.113137] systemd[1]: Listening on Process Core Dump Socket.
[    2.113211] systemd[1]: Listening on Journal Socket (/dev/log).
[    2.113257] systemd[1]: Listening on Journal Socket.
[    2.113296] systemd[1]: Listening on LVM2 metadata daemon socket.
[    2.114815] systemd[1]: Created slice User and Session Slice.
[    2.114825] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[    2.114830] systemd[1]: Reached target Slices.
[    2.123253] EXT4-fs (nvme0n1p2): re-mounted. Opts: (null)
[    2.129556] random: lvm: uninitialized urandom read (4 bytes read)
[    2.130951] random: systemd-random-: uninitialized urandom read (512 bytes read)
[    2.194062] usb 1-7: new full-speed USB device number 3 using xhci_hcd
[    2.296390] systemd-journald[341]: Received request to flush runtime journal from PID 1
[    2.310294] ACPI: AC Adapter [AC] (on-line)
[    2.312363] input: Intel HID events as /devices/platform/INT33D5:00/input/input5
[    2.313799] intel-hid INT33D5:00: platform supports 5 button array
[    2.313832] input: Intel HID 5 button array as /devices/platform/INT33D5:00/input/input6
[    2.319848] acpi PNP0C14:04: duplicate WMI GUID 05901221-D566-11D1-B2F0-00A0C9062910 (first instance was on PNP0C14:03)
[    2.319909] wmi_bus wmi_bus-PNP0C14:05: WQBC data block query control method not found
[    2.319911] acpi PNP0C14:05: duplicate WMI GUID 05901221-D566-11D1-B2F0-00A0C9062910 (first instance was on PNP0C14:03)
[    2.324509] acpi PNP0C14:06: duplicate WMI GUID 05901221-D566-11D1-B2F0-00A0C9062910 (first instance was on PNP0C14:03)
[    2.335177] usb 1-7: New USB device found, idVendor=27c6, idProduct=5395, bcdDevice= 1.00
[    2.335179] usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.335180] usb 1-7: Product: Goodix Fingerprint Device 
[    2.335181] usb 1-7: Manufacturer: HTMicroelectronics
[    2.335182] usb 1-7: SerialNumber: HTK32
[    2.354298] acpi PNP0C14:07: duplicate WMI GUID 05901221-D566-11D1-B2F0-00A0C9062910 (first instance was on PNP0C14:03)
[    2.355831] tpm_tis MSFT0101:00: 2.0 TPM (device-id 0xFC, rev-id 1)
[    2.371200] hidraw: raw HID events driver (C) Jiri Kosina
[    2.386319] input: PC Speaker as /devices/platform/pcspkr/input/input7
[    2.390928] Adding 39845884k swap on /dev/nvme0n1p3.  Priority:-2 extents:1 across:39845884k SSFS
[    2.394149] RAPL PMU: API unit is 2^-32 Joules, 5 fixed counters, 655360 ms ovfl timer
[    2.394150] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
[    2.394151] RAPL PMU: hw unit of domain package 2^-14 Joules
[    2.394151] RAPL PMU: hw unit of domain dram 2^-14 Joules
[    2.394152] RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules
[    2.394153] RAPL PMU: hw unit of domain psys 2^-14 Joules
[    2.394372] i801_smbus 0000:00:1f.4: SPD Write Disable is set
[    2.394444] i801_smbus 0000:00:1f.4: SMBus using PCI interrupt
[    2.399173] mei_me 0000:00:16.0: enabling device (0000 -> 0002)
[    2.404863] Linux agpgart interface v0.103
[    2.405196] proc_thermal 0000:00:04.0: enabling device (0000 -> 0002)
[    2.409677] cryptd: max_cpu_qlen set to 1000
[    2.419826] intel-lpss 0000:00:15.0: enabling device (0000 -> 0002)
[    2.426225] AVX2 version of gcm_enc/dec engaged.
[    2.426226] AES CTR mode by8 optimization enabled
[    2.440685] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    2.447062] idma64 idma64.0: Found Intel integrated DMA 64-bit
[    2.447977] input: Dell WMI hotkeys as /devices/platform/PNP0C14:05/wmi_bus/wmi_bus-PNP0C14:05/9DBB5994-A997-11DA-B012-B622A1EF5492/input/input9
[    2.450766] snd_hda_intel 0000:00:1f.3: enabling device (0000 -> 0002)
[    2.455015] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    2.455643] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    2.455645] cfg80211: failed to load regulatory.db
[    2.464023] usb 1-12: new high-speed USB device number 4 using xhci_hcd
[    2.481103] Intel(R) Wireless WiFi driver for Linux
[    2.481104] Copyright(c) 2003- 2015 Intel Corporation
[    2.481359] iwlwifi 0000:3b:00.0: enabling device (0000 -> 0002)
[    2.493380] iwlwifi 0000:3b:00.0: Found debug destination: EXTERNAL_DRAM
[    2.493381] iwlwifi 0000:3b:00.0: Found debug configuration: 0
[    2.493514] iwlwifi 0000:3b:00.0: loaded firmware version 48.13675109.0 op_mode iwlmvm
[    2.561510] checking generic (80000000 1fb0000) vs hw (80000000 10000000)
[    2.561511] fb0: switching to inteldrmfb from EFI VGA
[    2.561527] Console: switching to colour dummy device 80x25
[    2.561602] i915 0000:00:02.0: vgaarb: deactivate vga console
[    2.575452] MXM: GUID detected in BIOS
[    2.575503] ACPI Warning: \_SB.PCI0.GFX0._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20190509/nsarguments-59)
[    2.575607] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20190509/nsarguments-59)
[    2.583805] iwlwifi 0000:3b:00.0: Detected Killer(R) Wi-Fi 6 AX1650x 160MHz Wireless Network Adapter (200NGW), REV=0x340
[    2.597598] iwlwifi 0000:3b:00.0: Applying debug destination EXTERNAL_DRAM
[    2.597749] iwlwifi 0000:3b:00.0: Allocated 0x00400000 bytes for firmware monitor.
[    2.612493] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    2.612494] [drm] Driver supports precise vblank timestamp query.
[    2.612606] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem
[    2.614544] [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4)
[    2.614904] intel_rapl: Found RAPL domain package
[    2.614905] intel_rapl: Found RAPL domain core
[    2.614906] intel_rapl: Found RAPL domain uncore
[    2.614907] intel_rapl: Found RAPL domain dram
[    2.620580] usb 1-12: New USB device found, idVendor=0c45, idProduct=6723, bcdDevice=80.08
[    2.620581] usb 1-12: New USB device strings: Mfr=2, Product=1, SerialNumber=0
[    2.620582] usb 1-12: Product: Integrated_Webcam_HD
[    2.620583] usb 1-12: Manufacturer: CN09357G8LG0095FA9NGA01
[    2.626176] cdc_acm 1-7:1.0: ttyACM0: USB ACM device
[    2.626290] usbcore: registered new interface driver cdc_acm
[    2.626291] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    2.628557] media: Linux media interface: v0.10
[    2.658405] videodev: Linux video capture interface: v2.00
[    2.660261] Bluetooth: Core ver 2.22
[    2.660273] NET: Registered protocol family 31
[    2.660273] Bluetooth: HCI device and connection manager initialized
[    2.660276] Bluetooth: HCI socket layer initialized
[    2.660277] Bluetooth: L2CAP socket layer initialized
[    2.660279] Bluetooth: SCO socket layer initialized
[    2.668333] usbcore: registered new interface driver btusb
[    2.669299] Bluetooth: hci0: Bootloader revision 0.3 build 0 week 24 2017
[    2.670309] Bluetooth: hci0: Device revision is 1
[    2.670310] Bluetooth: hci0: Secure boot is enabled
[    2.670311] Bluetooth: hci0: OTP lock is enabled
[    2.670311] Bluetooth: hci0: API lock is enabled
[    2.670312] Bluetooth: hci0: Debug lock is disabled
[    2.670312] Bluetooth: hci0: Minimum firmware build 1 week 10 2014
[    2.671052] Bluetooth: hci0: Found device firmware: intel/ibt-20-1-3.sfi
[    2.673923] uvcvideo: Found UVC 1.00 device Integrated_Webcam_HD (0c45:6723)
[    2.678846] uvcvideo 1-12:1.0: Entity type for entity Extension 4 was not initialized!
[    2.678847] uvcvideo 1-12:1.0: Entity type for entity Extension 3 was not initialized!
[    2.678848] uvcvideo 1-12:1.0: Entity type for entity Processing 2 was not initialized!
[    2.678849] uvcvideo 1-12:1.0: Entity type for entity Camera 1 was not initialized!
[    2.678887] input: Integrated_Webcam_HD: Integrate as /devices/pci0000:00/0000:00:14.0/usb1/1-12/1-12:1.0/input/input10
[    2.678920] usbcore: registered new interface driver uvcvideo
[    2.678921] USB Video Class driver (1.1.1)
[    2.771649] iwlwifi 0000:3b:00.0: base HW address: d0:ab:d5:15:54:00
[    2.788296] thermal thermal_zone9: failed to read out thermal zone (-61)
[    2.790099] iwlwifi 0000:3b:00.0 wlp59s0: renamed from wlan0
[    2.920927] [drm] Initialized i915 1.6.0 20190417 for 0000:00:02.0 on minor 0
[    2.946261] pci 0000:01:00.0: optimus capabilities: enabled, status dynamic power, hda bios codec supported
[    2.946266] VGA switcheroo: detected Optimus DSM method \_SB_.PCI0.PEG0.PEGP handle
[    2.946266] nouveau: detected PR support, will not use DSM
[    2.946323] nouveau 0000:01:00.0: enabling device (0000 -> 0003)
[    2.947276] nouveau 0000:01:00.0: NVIDIA TU117 (167000a1)
[    2.998834] random: crng init done
[    3.007086] EXT4-fs (nvme0n1p4): mounted filesystem with ordered data mode. Opts: (null)
[    3.031372] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[    3.047665] nouveau 0000:01:00.0: bios: version 90.17.1c.40.4b
[    3.048312] nouveau 0000:01:00.0: fb: 4096 MiB GDDR5
[    3.056431] proc_thermal 0000:00:04.0: Creating sysfs group for PROC_THERMAL_PCI
[    3.091908] vga_switcheroo: enabled
[    3.092014] [TTM] Zone  kernel: Available graphics memory: 8025098 KiB
[    3.092015] [TTM] Zone   dma32: Available graphics memory: 2097152 KiB
[    3.092015] [TTM] Initializing pool allocator
[    3.092017] [TTM] Initializing DMA pool allocator
[    3.092028] nouveau 0000:01:00.0: DRM: VRAM: 4096 MiB
[    3.092029] nouveau 0000:01:00.0: DRM: GART: 536870912 MiB
[    3.092030] nouveau 0000:01:00.0: DRM: BIT table 'A' not found
[    3.092031] nouveau 0000:01:00.0: DRM: BIT table 'L' not found
[    3.092032] nouveau 0000:01:00.0: DRM: Pointer to TMDS table invalid
[    3.092032] nouveau 0000:01:00.0: DRM: DCB version 4.1
[    3.092222] nouveau 0000:01:00.0: DRM: failed to create kernel channel, -22
[    3.092399] nouveau 0000:01:00.0: DRM: MM: using COPY for buffer copies
[    3.124188] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input11
[    3.124335] ACPI: Video Device [PEGP] (multi-head: no  rom: yes  post: no)
[    3.124361] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:0b/LNXVIDEO:01/input/input12
[    3.124502] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
[    3.134874] 0000:01:00.0 initialised, 1048576 pages in 7ms
[    3.135233] fbcon: i915drmfb (fb0) is primary device
[    3.140105] nouveau 0000:01:00.0: DRM: DMEM: registered 4096MB of device memory
[    3.140196] [drm] Initialized nouveau 1.3.1 20120801 for 0000:01:00.0 on minor 1
[    3.209617] psmouse serio1: synaptics: queried max coordinates: x [..5664], y [..4646]
[    3.213250] battery: ACPI: Battery Slot [BAT0] (battery present)
[    3.239396] psmouse serio1: synaptics: queried min coordinates: x [1278..], y [1206..]
[    3.239399] psmouse serio1: synaptics: Your touchpad (PNP: DLL0905 PNP0f13) says it can support a different bus. If i2c-hid and hid-rmi are not used, you might want to try setting psmouse.synaptics_intertouch to 1 and report this to linux-input@vger.kernel.org.
[    3.296729] psmouse serio1: synaptics: Touchpad model: 1, fw: 8.2, id: 0x1e2b1, caps: 0xf00123/0x840300/0x12e800/0x0, board id: 3125, fw id: 2378871
[    3.331811] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8
[    3.341752] mousedev: PS/2 mouse device common for all mice
[    3.475722] iTCO_vendor_support: vendor-support=0
[    3.481001] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[    3.481247] iTCO_wdt iTCO_wdt: can't request region for resource [mem 0x00c5fffc-0x00c5ffff]
[    3.481251] iTCO_wdt: probe of iTCO_wdt failed with error -16
[    3.613223] intel-lpss 0000:00:15.1: enabling device (0000 -> 0002)
[    3.613488] idma64 idma64.1: Found Intel integrated DMA 64-bit
[    3.672066] i2c_hid i2c-SYNA2393:00: i2c-SYNA2393:00 supply vdd not found, using dummy regulator
[    3.672073] i2c_hid i2c-SYNA2393:00: i2c-SYNA2393:00 supply vddl not found, using dummy regulator
[    4.302627] Bluetooth: hci0: Waiting for firmware download to complete
[    4.303353] Bluetooth: hci0: Firmware loaded in 1596697 usecs
[    4.303432] Bluetooth: hci0: Waiting for device to boot
[    4.316383] Bluetooth: hci0: Device booted in 12697 usecs
[    4.316603] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-20-1-3.ddc
[    4.331416] Bluetooth: hci0: Applying Intel DDC parameters completed
[    4.991441] Console: switching to colour frame buffer device 480x135
[    5.016355] i915 0000:00:02.0: fb0: i915drmfb frame buffer device
[    5.077051] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC3266: line_outs=1 (0x17/0x0/0x0/0x0/0x0) type:speaker
[    5.077052] snd_hda_codec_realtek hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[    5.077053] snd_hda_codec_realtek hdaudioC0D0:    hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[    5.077053] snd_hda_codec_realtek hdaudioC0D0:    mono: mono_out=0x0
[    5.077054] snd_hda_codec_realtek hdaudioC0D0:    inputs:
[    5.077055] snd_hda_codec_realtek hdaudioC0D0:      Headset Mic=0x18
[    5.077055] snd_hda_codec_realtek hdaudioC0D0:      Headphone Mic=0x1a
[    5.077056] snd_hda_codec_realtek hdaudioC0D0:      Internal Mic=0x12
[    5.134898] input: HDA Intel PCH Headphone Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input13
[    5.134963] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input14
[    5.135005] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input15
[    5.135096] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input16
[    5.135157] input: HDA Intel PCH HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input17
[    5.135217] input: HDA Intel PCH HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input18
[    5.161384] input: SYNA2393:00 06CB:7A13 Mouse as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-27/i2c-SYNA2393:00/0018:06CB:7A13.0001/input/input19
[    5.161612] input: SYNA2393:00 06CB:7A13 Touchpad as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-27/i2c-SYNA2393:00/0018:06CB:7A13.0001/input/input20
[    5.161897] hid-generic 0018:06CB:7A13.0001: input,hidraw0: I2C HID v1.00 Mouse [SYNA2393:00 06CB:7A13] on i2c-SYNA2393:00
[    5.330299] input: SYNA2393:00 06CB:7A13 Touchpad as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-27/i2c-SYNA2393:00/0018:06CB:7A13.0001/input/input23
[    5.330524] hid-multitouch 0018:06CB:7A13.0001: input,hidraw0: I2C HID v1.00 Mouse [SYNA2393:00 06CB:7A13] on i2c-SYNA2393:00
[   52.491407] nouveau 0000:01:00.0: Refused to change power state, currently in D3
[   73.974006] nouveau 0000:01:00.0: DRM: failed to idle channel 0 [DRM]
[  171.583994] nouveau 0000:01:00.0: DRM: failed to idle channel 0 [DRM]
[  380.173961] nouveau 0000:01:00.0: DRM: failed to idle channel 0 [DRM]
[  380.174491] ------------[ cut here ]------------
[  380.174491] nouveau 0000:01:00.0: disabling already-disabled device
[  380.174498] WARNING: CPU: 9 PID: 298 at drivers/pci/pci.c:1923 pci_disable_device+0x8c/0xb0
[  380.174498] Modules linked in: hid_multitouch snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic hid_generic mei_hdcp mei_wdt iTCO_wdt iTCO_vendor_support joydev mousedev arc4 uvcvideo btusb videobuf2_vmalloc videobuf2_memops btrtl videobuf2_v4l2 btbcm btintel videobuf2_common bluetooth videodev media ecdh_generic cdc_acm ecc intel_rapl x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel kvm iwlmvm nouveau i915 irqbypass mac80211 sof_pci_dev snd_sof_intel_hda_common snd_sof_intel_hda snd_sof_intel_byt snd_sof_intel_ipc snd_sof snd_sof_xtensa_dsp snd_soc_skl snd_soc_hdac_hda snd_hda_ext_core snd_soc_skl_ipc snd_soc_sst_ipc snd_soc_sst_dsp snd_soc_acpi_intel_match snd_soc_acpi iwlwifi snd_soc_core crct10dif_pclmul ttm crc32_pclmul i2c_algo_bit ghash_clmulni_intel snd_compress drm_kms_helper ac97_bus snd_pcm_dmaengine dell_laptop snd_hda_intel ledtrig_audio dell_wmi snd_hda_codec drm idma64 aesni_intel dell_smbios cfg80211 snd_hda_core snd_hwdep snd_pcm aes_x86_64 crypto_simd
[  380.174515]  cryptd glue_helper intel_gtt snd_timer intel_cstate agpgart intel_uncore mei_me syscopyarea sysfillrect sysimgblt dell_wmi_descriptor wmi_bmof processor_thermal_device intel_lpss_pci dcdbas psmouse ucsi_acpi snd typec_ucsi tpm_crb input_leds mxm_wmi intel_wmi_thunderbolt rtsx_pci_ms intel_rapl_perf thunderbolt pcspkr soundcore i2c_i801 mei memstick rfkill fb_sys_fops i2c_hid intel_lpss intel_soc_dts_iosf intel_pch_thermal typec evdev mac_hid hid battery tpm_tis tpm_tis_core int3403_thermal int340x_thermal_zone tpm dell_smo8800 wmi rng_core int3400_thermal pcc_cpufreq intel_hid acpi_thermal_rel sparse_keymap ac ip_tables x_tables ext4 crc32c_generic crc16 mbcache jbd2 rtsx_pci_sdmmc mmc_core serio_raw atkbd libps2 ahci libahci libata xhci_pci crc32c_intel xhci_hcd rtsx_pci scsi_mod i8042 serio
[  380.174530] CPU: 9 PID: 298 Comm: kworker/9:2 Not tainted 5.2.0-arch2-1-ARCH #1
[  380.174531] Hardware name: Dell Inc. XPS 15 7590/0VYV0G, BIOS 1.1.1 05/31/2019
[  380.174532] Workqueue: pm pm_runtime_work
[  380.174534] RIP: 0010:pci_disable_device+0x8c/0xb0
[  380.174535] Code: 4d 85 e4 75 07 4c 8b a3 b0 00 00 00 48 8d bb b0 00 00 00 e8 16 04 15 00 4c 89 e2 48 c7 c7 c8 0c b0 a8 48 89 c6 e8 c3 76 bd ff <0f> 0b eb 8e 48 89 df e8 e8 fe ff ff 80 a3 c9 07 00 00 df 5b 41 5c
[  380.174535] RSP: 0018:ffff91c7c2297d40 EFLAGS: 00010286
[  380.174536] RAX: 0000000000000000 RBX: ffff8b69293de000 RCX: 0000000000000000
[  380.174536] RDX: 0000000000000037 RSI: ffffffffa929d437 RDI: 0000000000000246
[  380.174537] RBP: ffff8b69293de0b0 R08: 00000058842a5fb1 R09: 0000000000000037
[  380.174537] R10: ffffffffa929d7e0 R11: ffffffffa929d407 R12: ffff8b69293a4b30
[  380.174538] R13: 00000000fffffff0 R14: 0000000000000000 R15: ffff8b6924ea0000
[  380.174538] FS:  0000000000000000(0000) GS:ffff8b692c440000(0000) knlGS:0000000000000000
[  380.174539] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  380.174539] CR2: 00007f173f80c984 CR3: 000000000fa0a002 CR4: 00000000003606e0
[  380.174540] Call Trace:
[  380.174568]  nouveau_pmops_runtime_suspend+0x53/0xa0 [nouveau]
[  380.174570]  pci_pm_runtime_suspend+0x58/0x140
[  380.174571]  ? __switch_to_asm+0x40/0x70
[  380.174572]  ? pci_has_legacy_pm_support+0x70/0x70
[  380.174573]  __rpm_callback+0x7b/0x130
[  380.174574]  ? pci_has_legacy_pm_support+0x70/0x70
[  380.174575]  rpm_callback+0x1f/0x70
[  380.174576]  rpm_suspend+0x136/0x610
[  380.174577]  pm_runtime_work+0x94/0xa0
[  380.174578]  process_one_work+0x1d1/0x3e0
[  380.174579]  worker_thread+0x4a/0x3d0
[  380.174581]  kthread+0xfb/0x130
[  380.174581]  ? process_one_work+0x3e0/0x3e0
[  380.174582]  ? kthread_park+0x90/0x90
[  380.174583]  ret_from_fork+0x35/0x40
[  380.174584] ---[ end trace 161db7215c37e20e ]---
[  403.050642] nouveau 0000:01:00.0: DRM: failed to idle channel 0 [DRM]

Offline

#7 2019-07-14 04:25:55

Noxult
Member
Registered: 2019-07-13
Posts: 12

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

@rbrinson

1. Arch_Linux_Archive#Finding_packages_in_the_Historical_Archive
https://wiki.archlinux.org/index.php/Ar … al_Archive
2. Just follow the procedure given by the arch wiki page of DELL XPS 15 7590
3. In fact I am also new to Arch, so, I don't know.

Offline

#8 2019-07-14 17:09:39

rbrinson
Member
Registered: 2019-07-12
Posts: 16

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

Hey, @Noxult and/or @loqs. I just saw that Linux version 5.2.1 was just dropped a couple of hours ago in the Arch Linux git repo. I don't think it is in the Core package repository yet, but when it hits, would one of you mind checking out whether or not the Arch build of Linux 5.2.1 with the current linux-firmware package will just work out of the box with the killer ax1650 wireless network adapter. I would check it myself, but after unsuccessfully trying to create an Arch package for Linux 5.1.16 with the patch from the Killer Networking website, I decided to reinstall the Windows image that I made with Clonezilla before starting the process of installing Arch. I figured I will just have to wait for working killer ax1650 support to make its way into the iwlwifi kernel module and/or the linux-firmware package. Thank you!

Offline

#9 2019-07-14 17:54:53

progandy
Member
Registered: 2012-05-17
Posts: 5,184

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

I don't see any iwlwifi changes in the 5.2.1 release compared to 5.2.0. The killer firmware loading patch is already included in 5.2.0.

https://git.kernel.org/pub/scm/linux/ke … .2..v5.2.1

There are changes in git tree for 5.3,

https://git.kernel.org/pub/scm/linux/ke … .2..master

Last edited by progandy (2019-07-14 18:09:29)


| alias CUTF='LANG=en_XX.UTF-8@POSIX ' |

Offline

#10 2019-07-14 22:14:40

rbrinson
Member
Registered: 2019-07-12
Posts: 16

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

@progandy, thank you for the links, but that is unfortunate. I know that the patch for loading the killer ax1650 firmware was added to the 5.2.0 kernel, and the boot process does properly identify the hardware. However, the firmware fails to load for some reason. There's definitely a problem either with the kernel module as shipped in 5.2.0 or in the 20190628.70e4394-1 linux-firmware package.

Offline

#11 2019-07-15 00:13:44

loqs
Member
Registered: 2014-03-06
Posts: 17,196

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

@progandy perhaps in prepare() `git cherry-pick -m 1 237f83dfbe668443b5e31c3c7576125871cca674` to cherry-pick the 5.3 net merge?
This would limit the amount of new material,  although it is still very large.

Offline

#12 2019-07-15 08:34:51

progandy
Member
Registered: 2012-05-17
Posts: 5,184

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

@loqs: maybe, or is it possible to merge one of the iwlwifi trees or maybe somehow use the backports? I have never done that, so I don't know the process for that. https://git.kernel.org/pub/scm/linux/ke … t/iwlwifi/


@rbrinson: As for firmware, you could try the package 20190514.711d329 or remove usr/lib/firmware/iwlwifi-cc-a0-48.ucode to force use of the -46 firmware.


| alias CUTF='LANG=en_XX.UTF-8@POSIX ' |

Offline

#13 2019-07-16 02:56:30

Noxult
Member
Registered: 2019-07-13
Posts: 12

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

@progandy Now I have a Linux 5.1.16 running using the newest firmware available (that is, using the backports) without any wireless connection issue, while running Linux kernel 5.2 with the same setting and the same firmware(even if I backported again with the same procedure I followed when on Linux 5.1.16) throws out the error aformentioned, so it is highly probable that something is wrong with the kernel not the firmware. Moreover iwlwifi-cc-a0-48.ucode works perfectly on kernel 5.1.16.

Offline

#14 2019-07-16 14:22:03

rbrinson
Member
Registered: 2019-07-12
Posts: 16

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

HI, @Noxult, I didn't know if you had noticed, but packages for linux-5.2.1 and a newer linux-firmware (20190712.d52556e-1) have been dropped into the Core repository. If you have the time and are willing, would you mind testing to see if the Killer AX1650 will work with this new kernel and firmware combination? Thanks!

Offline

#15 2019-07-16 22:47:02

loqs
Member
Registered: 2014-03-06
Posts: 17,196

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

@progandy I tried backports which has the common issue of expecting python to be python2 I was able to get it to produce a backport that failed against 5.2.1
due to https://github.com/torvalds/linux/commi … 627c307110 while backports uses https://www.spinics.net/lists/backports/msg04680.html
even if I patch that then it fails due to 5.2.1 not having https://github.com/torvalds/linux/commi … cc800d3f5b

Offline

#16 2019-07-17 07:52:11

Noxult
Member
Registered: 2019-07-13
Posts: 12

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

@rbrinson Gave a try and still no luck. Same dmesg output.
And again I've pacman -U ed solely the linux kernel leaving the newest firmware untouched, everything works fine on kernel 5.1.16.

Last edited by Noxult (2019-07-17 07:59:39)

Offline

#17 2019-07-17 16:07:36

rbrinson
Member
Registered: 2019-07-12
Posts: 16

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

@Noxult, bummer. Thanks for trying!

Offline

#18 2019-07-18 04:50:22

tomberek
Member
Registered: 2019-07-18
Posts: 3

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

I can also verify on a Dell XPS 15 7590 that 5.1.18 can see and use the card, but 5.2.1 does not work.

Offline

#19 2019-07-19 04:21:54

rbrinson
Member
Registered: 2019-07-12
Posts: 16

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

Hey, @tomberek. I'm trying to follow the instructions on the Arch Wiki page for the Dell XPS 15 7590, and build the backport-iwlwifi repository with the current 5.2.1 kernel. Unfortunately I am getting an error during the 'make -j4' command. It says:

make[4] *** [Makefile:1595: backport-iwlwifi] Error 2
make[3] *** [Makefile.build:6: modules] Error 2
make[2] *** [Makefile.real:100: modules] Error 2
make[1] *** [Makefile:43: modules] Error 2
make: *** [Makefile:30: default] Error 2

Did you run into anything like this? do you or anybody else have any idea as to what the problem could be? Thanks!

Offline

#20 2019-07-19 06:49:17

Noxult
Member
Registered: 2019-07-13
Posts: 12

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

@rbrinson Oh I think the wiki page could be somehow misleading for it was written when the latest kernel available was 5.1.16. I don't think building it on 5.2.1 will help, since I've done that already.
As for the error you're now encountering, it is rather strange.. I've also got that error message when trying to make -j4 it (cloned about a week ago),then I re-cloned the repo and followed the procedure again, the error is gone.
I compared the output and found these lines in the ouput of the failed attempt

 CC [M]  /home/noxultranonerit/temp/backport-iwlwifi/net/mac80211/iface.o
  CC [M]  /home/noxultranonerit/temp/backport-iwlwifi/net/wireless/ap.o
/home/noxultranonerit/temp/backport-iwlwifi/net/mac80211/iface.c:2114:1: fatal error: opening dependency file /home/noxultranonerit/temp/backport-iwlwifi/net/mac80211/.iface.o.d: Permission denied
 2114 | }
      | ^
compilation terminated.
make[6]: *** [scripts/Makefile.build:276: /home/noxultranonerit/temp/backport-iwlwifi/net/mac80211/iface.o] Error 1
make[5]: *** [scripts/Makefile.build:486: /home/noxultranonerit/temp/backport-iwlwifi/net/mac80211] Error 2
make[5]: *** Waiting for unfinished jobs....
  CC [M]  /home/noxultranonerit/temp/backport-iwlwifi/net/wireless/trace.o

which in the success attempt shows something like

CC [M]  /home/noxultranonerit/temp/backport-iwlwifi/drivers/net/wireless/intel/iwlwifi/mvm/rs-fw.o
  CC [M]  /home/noxultranonerit/temp/backport-iwlwifi/net/wireless/ap.o
  CC [M]  /home/noxultranonerit/temp/backport-iwlwifi/net/mac80211/he.o
  CC [M]  /home/noxultranonerit/temp/backport-iwlwifi/drivers/net/wireless/intel/iwlwifi/iwl-eeprom-parse.o
  CC [M]  /home/noxultranonerit/temp/backport-iwlwifi/drivers/net/wireless/intel/iwlwifi/mvm/power.o
  CC [M]  /home/noxultranonerit/temp/backport-iwlwifi/net/wireless/trace.o

Offline

#21 2019-07-19 09:21:00

tomberek
Member
Registered: 2019-07-18
Posts: 3

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

Progress with 5.2.1:
Using https://git.kernel.org/pub/scm/linux/ke … rmware.git
on revision: bf13a71b18af229b4c900b321ef1f8443028ded8
then:

rm /lib/firmware/iwlwifi-cc-a0-48.ucode                         

And wireless works. It seems the cc-a0-48 would get loaded by mistake and perpetually fail, cycling the card. Remove cc-a0-48 and cc-a0-46 gets loaded.


[    4.269672] iwlwifi 0000:3b:00.0: enabling device (0000 -> 0002)
[    4.277593] iwlwifi 0000:3b:00.0: Direct firmware load for iwlwifi-cc-a0-48.ucode failed with error -2
[    4.277599] iwlwifi 0000:3b:00.0: Direct firmware load for iwlwifi-cc-a0-47.ucode failed with error -2
[    4.280181] iwlwifi 0000:3b:00.0: loaded firmware version 46.3cfab8da.0 op_mode iwlmvm
[    4.330162] iwlwifi 0000:3b:00.0: Detected Killer(R) Wi-Fi 6 AX1650x 160MHz Wireless Network Adapter (200NGW), REV=0x340
[    4.613134] iwlwifi 0000:3b:00.0 wlp59s0: renamed from wlan0

Offline

#22 2019-07-19 13:46:19

Noxult
Member
Registered: 2019-07-13
Posts: 12

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

@tomberek Thanks for the information, I'll give it a try.
Seems that there are some collision between the newer kernels and firmware version 48. For '[    2.744043] iwlwifi 0000:3b:00.0: loaded firmware version 48.13675109.0 op_mode iwlmvm' the 48th version firmware works perfectl on older kernels.

==================

Yes, it works. You don't even need to build the newest firmware, just pacman -Syu and remove the version 48 ucode and reboot.
For the time moment one should avoid updating the linux-firmware package, or should remove the ucode 48 file after each update of the package.

Last edited by Noxult (2019-07-19 13:56:34)

Offline

#23 2019-07-20 02:26:31

rbrinson
Member
Registered: 2019-07-12
Posts: 16

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

@tomberek and @Noxult, I can also confirm that removing or renaming the /lib/firmware/iwlwifi-cc-a0-48.ucode file that is installed with the linux-firmware_20190712.d52556e-1 package allows me to use wifi-menu to scan for and connect to my access point on Linux 5.2.1. This is not a perfect solution, but hey, I can ping google and run pacman! This linux-firmware package is already flagged as out-of-date in the Arch packages repository. So, maybe the next release will be better...but probably not! At least we now know how to get to a working state for the Killer AX1650 on the XPS 15 7590.

Offline

#24 2019-07-20 09:29:41

Noxult
Member
Registered: 2019-07-13
Posts: 12

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

Oh it should be noted that the latest kernel just doubles the energy consumption under normal usage, like from 6W to 13W, and the CPU package temperature easily exceeds 50 celcius while on kernel 5.1.16 it was around 45 celcius.. It is just like running windows.

Offline

#25 2019-07-22 01:37:39

tomberek
Member
Registered: 2019-07-18
Posts: 3

Re: [SOLVED] Killer AX1650 Wireless Adapter Not Working on Linux 5.2.0

@Noxult: Let's investigate and fix. What have you learned about the problem so far?

Offline

Board footer

Powered by FluxBB