You are not logged in.

#1 2007-08-03 07:40:55

vivek_ars
Member
Registered: 2007-08-03
Posts: 13

Cannot Detect On Board Ethernet Card

hi,

i am using arch linux on p4 3ghz, i am unable to configure my network b'coz arch linux is unable to detect onboard ethernet adapter, i had tried to detect with command hwd -h (which normally works to detect the network and ethernet adapter) but it shows no network or ethernet card found. The other part when i use the same computer for xp it (network) works. can somebody pls solve the problem.

Offline

#2 2007-08-03 08:11:30

STiAT
Member
From: Vienna, Austria
Registered: 2004-12-23
Posts: 606

Re: Cannot Detect On Board Ethernet Card

A very undetailed description. If at least the comparison system had been any other linux distribution.

Please, post the output of

lspci

or

lspci |grep Net

So we at least know which card you're talking about (card, chipset, revision).


Ability is nothing without opportunity.

Offline

#3 2007-08-03 08:37:08

vivek_ars
Member
Registered: 2007-08-03
Posts: 13

Re: Cannot Detect On Board Ethernet Card

output of lspci |grep net

04:08.0 Ehternet controller:Intel corp.:Unknown device 1094 (rev 01)

Offline

#4 2007-08-03 09:05:47

STiAT
Member
From: Vienna, Austria
Registered: 2004-12-23
Posts: 606

Re: Cannot Detect On Board Ethernet Card

Hmh, hard to say, since it's not specified at all.

I'd like to see the output of

lspci -vvv

for the card above.

A lot of those intel chipsets which are unknown devices work with the eepro100 driver, what might be worth a try.

Yours,
Georg


Ability is nothing without opportunity.

Offline

#5 2007-08-04 06:13:52

vivek_ars
Member
Registered: 2007-08-03
Posts: 13

Re: Cannot Detect On Board Ethernet Card

OUTPUT OF lspci -vvvv



00:00.0 Host bridge: Intel Corp.: Unknown device 2770 (rev 02)
    Subsystem: Intel Corp.: Unknown device d605
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
    Latency: 0
    Capabilities: <available only to root>

00:02.0 VGA compatible controller: Intel Corp.: Unknown device 2772 (rev 02) (prog-if 00 [VGA])
    Subsystem: Intel Corp.: Unknown device d605
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin A routed to IRQ 11
    Region 0: Memory at 30100000 (32-bit, non-prefetchable) [size=512K]
    Region 1: I/O ports at 20e0 [size=8]
    Region 2: Memory at 20000000 (32-bit, prefetchable) [size=256M]
    Region 3: Memory at 30180000 (32-bit, non-prefetchable) [size=256K]
    Expansion ROM at <unassigned> [disabled]
    Capabilities: <available only to root>

00:1b.0 Class 0403: Intel Corp.: Unknown device 27d8 (rev 01)
    Subsystem: Intel Corp.: Unknown device d605
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0, cache line size 10
    Interrupt: pin A routed to IRQ 9
    Region 0: Memory at 301c0000 (64-bit, non-prefetchable) [size=16K]
    Capabilities: <available only to root>

00:1c.0 PCI bridge: Intel Corp.: Unknown device 27d0 (rev 01) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0, cache line size 10
    Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: fff00000-000fffff
    Prefetchable memory behind bridge: fffffffffff00000-0000000000000000
    BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
    Capabilities: <available only to root>

00:1c.2 PCI bridge: Intel Corp.: Unknown device 27d4 (rev 01) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0, cache line size 10
    Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: fff00000-000fffff
    Prefetchable memory behind bridge: fffffffffff00000-0000000000000000
    BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
    Capabilities: <available only to root>

00:1c.3 PCI bridge: Intel Corp.: Unknown device 27d6 (rev 01) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0, cache line size 10
    Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: fff00000-000fffff
    Prefetchable memory behind bridge: fffffffffff00000-0000000000000000
    BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
    Capabilities: <available only to root>

00:1d.0 USB Controller: Intel Corp.: Unknown device 27c8 (rev 01) (prog-if 00 [UHCI])
    Subsystem: Intel Corp.: Unknown device d605
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin A routed to IRQ 23
    Region 4: I/O ports at 2080 [size=32]

00:1d.1 USB Controller: Intel Corp.: Unknown device 27c9 (rev 01) (prog-if 00 [UHCI])
    Subsystem: Intel Corp.: Unknown device d605
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin B routed to IRQ 19
    Region 4: I/O ports at 2060 [size=32]

00:1d.2 USB Controller: Intel Corp.: Unknown device 27ca (rev 01) (prog-if 00 [UHCI])
    Subsystem: Intel Corp.: Unknown device d605
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin C routed to IRQ 18
    Region 4: I/O ports at 2040 [size=32]

00:1d.3 USB Controller: Intel Corp.: Unknown device 27cb (rev 01) (prog-if 00 [UHCI])
    Subsystem: Intel Corp.: Unknown device d605
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin D routed to IRQ 16
    Region 4: I/O ports at 2020 [size=32]

00:1d.7 USB Controller: Intel Corp.: Unknown device 27cc (rev 01) (prog-if 20 [EHCI])
    Subsystem: Intel Corp.: Unknown device d605
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin A routed to IRQ 23
    Region 0: Memory at 301c4000 (32-bit, non-prefetchable) [size=1K]
    Capabilities: <available only to root>

00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB PCI Bridge (rev e1) (prog-if 01 [Subtractive decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
    I/O behind bridge: 00001000-00001fff
    Memory behind bridge: 30000000-300fffff
    Prefetchable memory behind bridge: fffffffffff00000-0000000000000000
    BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
    Capabilities: <available only to root>

00:1f.0 ISA bridge: Intel Corp.: Unknown device 27b8 (rev 01)
    Subsystem: Intel Corp.: Unknown device d605
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Capabilities: <available only to root>

00:1f.1 IDE interface: Intel Corp.: Unknown device 27df (rev 01) (prog-if 8a [Master SecP PriP])
    Subsystem: Intel Corp.: Unknown device d605
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin A routed to IRQ 18
    Region 0: I/O ports at <unassigned>
    Region 1: I/O ports at <unassigned>
    Region 2: I/O ports at <unassigned>
    Region 3: I/O ports at <unassigned>
    Region 4: I/O ports at 20b0 [size=16]

00:1f.2 IDE interface: Intel Corp.: Unknown device 27c0 (rev 01) (prog-if 8f [Master SecP SecO PriP PriO])
    Subsystem: Intel Corp.: Unknown device d605
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin B routed to IRQ 19
    Region 0: I/O ports at 20c8 [size=8]
    Region 1: I/O ports at 20ec [size=4]
    Region 2: I/O ports at 20c0 [size=8]
    Region 3: I/O ports at 20e8 [size=4]
    Region 4: I/O ports at 20a0 [size=16]
    Capabilities: <available only to root>

00:1f.3 SMBus: Intel Corp.: Unknown device 27da (rev 01)
    Subsystem: Intel Corp.: Unknown device d605
    Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin B routed to IRQ 11
    Region 4: I/O ports at 2000 [size=32]

04:08.0 Ethernet controller: Intel Corp.: Unknown device 1094 (rev 01)
    Subsystem: Intel Corp.: Unknown device d605
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32 (2000ns min, 14000ns max), cache line size 10
    Interrupt: pin A routed to IRQ 10
    Region 0: Memory at 30000000 (32-bit, non-prefetchable) [size=4K]
    Region 1: I/O ports at 1000 [size=64]
    Capabilities: <available only to root>

Offline

Board footer

Powered by FluxBB