Arch Linux

woodykiang

Member

Registered: 2009-01-25

Posts: 13

I can't connect my Sony Ericsson w980

Every times after I connect it to my box, dmesg give me tons of continually, and no /dev/sdx# is created.

usb 1-3: new high speed USB device using ehci_hcd and address 6
usb 1-3: configuration #2 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
scsi 2:0:0:0: Direct-Access     Sony Eri Memory Stick        0 PQ: 0 ANSI: 0
sd 2:0:0:0: [sdb] 15520084 512-byte hardware sectors: (7.94 GB/7.40 GiB)
sd 2:0:0:0: [sdb] Test WP failed, assume Write Enabled
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] 15520084 512-byte hardware sectors: (7.94 GB/7.40 GiB)
sd 2:0:0:0: [sdb] Test WP failed, assume Write Enabled
sd 2:0:0:0: [sdb] Assuming drive cache: write through
 sdb: sdb1
sd 2:0:0:0: [sdb] Attached SCSI removable disk
sd 2:0:0:0: Attached scsi generic sg2 type 0
usb-storage: device scan complete
sd 2:0:0:0: [sdb] Sense Key : 0x0 [current] 
sd 2:0:0:0: [sdb] ASC=0x0 ASCQ=0x0
sd 2:0:0:0: [sdb] Sense Key : 0x0 [current] 
sd 2:0:0:0: [sdb] ASC=0x0 ASCQ=0x0
sd 2:0:0:0: [sdb] Sense Key : 0x0 [current] 
sd 2:0:0:0: [sdb] ASC=0x0 ASCQ=0x0
...
...
...
sd 2:0:0:0: [sdb] Sense Key : 0x0 [current] 
sd 2:0:0:0: [sdb] ASC=0x0 ASCQ=0x0

% uname -r
2.6.29-ARCH

% lsusb -v
Bus 001 Device 006: ID 0fce:e0da Sony Ericsson Mobile Communications AB 
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  idVendor           0x0fce Sony Ericsson Mobile Communications AB
  idProduct          0xe0da 
  bcdDevice            0.00
  iManufacturer           1 
  iProduct                2 
  iSerial                 3 
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     2
    iConfiguration          6 
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              500mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         8 Mass Storage
      bInterfaceSubClass      6 SCSI
      bInterfaceProtocol     80 Bulk (Zip)
      iInterface              7 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x05  EP 5 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x85  EP 5 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0

It works in Ubuntu 8.04 live CD (kernel 2.6.24)
Here is the dmesg of Ubuntu.

[  334.477333] usb 5-4: new high speed USB device using ehci_hcd and address 7
[  335.197253] usb 5-4: configuration #2 chosen from 1 choice
[  336.046146] usbcore: registered new interface driver libusual
[  336.091689] Initializing USB Mass Storage driver...
[  336.091961] scsi2 : SCSI emulation for USB Mass Storage devices
[  336.092193] usbcore: registered new interface driver usb-storage
[  336.092198] USB Mass Storage support registered.
[  336.092782] usb-storage: device found at 7
[  336.092786] usb-storage: waiting for device to settle before scanning
[  341.090541] usb-storage: device scan complete
[  341.091150] scsi 2:0:0:0: Direct-Access     Sony Eri Memory Stick        0 PQ: 0 ANSI: 0
[  341.103504] sd 2:0:0:0: [sdb] 15520084 512-byte hardware sectors (7946 MB)
[  341.104750] sd 2:0:0:0: [sdb] Test WP failed, assume Write Enabled
[  341.104756] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[  341.106868] sd 2:0:0:0: [sdb] 15520084 512-byte hardware sectors (7946 MB)
[  341.108121] sd 2:0:0:0: [sdb] Test WP failed, assume Write Enabled
[  341.108126] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[  341.108131]  sdb: sdb1
[  341.111040] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[  341.111095] sd 2:0:0:0: Attached scsi generic sg2 type 0
[  341.362012] sd 2:0:0:0: [sdb] Sense Key : No Sense [current] 
[  341.362023] sd 2:0:0:0: [sdb] Add. Sense: No additional sense information
[  341.413988] sd 2:0:0:0: [sdb] Sense Key : No Sense [current] 
[  341.413994] sd 2:0:0:0: [sdb] Add. Sense: No additional sense information
[  341.465967] sd 2:0:0:0: [sdb] Sense Key : No Sense [current] 
[  341.465974] sd 2:0:0:0: [sdb] Add. Sense: No additional sense information
[  341.530065] sd 2:0:0:0: [sdb] Sense Key : No Sense [current] 
[  341.530083] sd 2:0:0:0: [sdb] Add. Sense: No additional sense information
[  341.581794] sd 2:0:0:0: [sdb] Sense Key : No Sense [current] 
[  341.581801] sd 2:0:0:0: [sdb] Add. Sense: No additional sense information
[  341.742247] sd 2:0:0:0: [sdb] Sense Key : No Sense [current] 
[  341.742260] sd 2:0:0:0: [sdb] Add. Sense: No additional sense information
[  341.793841] sd 2:0:0:0: [sdb] Sense Key : No Sense [current] 
[  341.793853] sd 2:0:0:0: [sdb] Add. Sense: No additional sense information
[  547.577089] kjournald starting.  Commit interval 5 seconds
[  547.577100] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
[  547.583182] EXT3 FS on sda1, internal journal
[  547.583191] EXT3-fs: mounted filesystem with ordered data mode.
[  560.824670] SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
[  560.825713] SGI XFS Quota Management subsystem
[  560.874977] XFS mounting filesystem sda10
[  561.056773] Ending clean XFS mount for filesystem: sda10

It seems that arch linux is retrying something continually and Ubuntu stop trying after several times?

Thanks

Last edited by woodykiang (2009-05-03 09:38:27)

woodykiang

Member

Registered: 2009-01-25

Posts: 13

Re: I can't connect my Sony Ericsson w980

I recompiled a debug enabled usb-storage and this is the log.(but I'm not quite understand it)

usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x10070000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage:  28 00 00 ec d1 40 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x641 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code -32; transferred 2048/4096
usb-storage: clearing endpoint halt for pipe 0xc0028680
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=85 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Bulk data transfer result 0x2
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x641 R 2048 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: -- unexpectedly short transfer
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x642 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x642 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x10070000
usb-storage: *** thread sleeping.
sd 2:0:0:0: [sdb] Sense Key : 0x0 [current] 
sd 2:0:0:0: [sdb] ASC=0x0 ASCQ=0x0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage:  28 00 00 ec d1 40 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x643 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code -32; transferred 2048/4096
usb-storage: clearing endpoint halt for pipe 0xc0028680
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=85 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Bulk data transfer result 0x2
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x643 R 2048 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: -- unexpectedly short transfer
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x644 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x644 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x10070000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage:  28 00 00 ec d1 40 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x645 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code -32; transferred 2048/4096
usb-storage: clearing endpoint halt for pipe 0xc0028680
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=85 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Bulk data transfer result 0x2
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x645 R 2048 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: -- unexpectedly short transfer
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x646 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x646 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x10070000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage:  28 00 00 ec d1 40 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x647 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code -32; transferred 2048/4096
usb-storage: clearing endpoint halt for pipe 0xc0028680
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=85 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Bulk data transfer result 0x2
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x647 R 2048 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: -- unexpectedly short transfer
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x648 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x648 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x10070000

senaxo

Member

From: The Netherlands

Registered: 2009-08-03

Posts: 6

Re: I can't connect my Sony Ericsson w980

I bump into the same problem, dmesg shows the 'Sense Key' loop and no /dev/sdx is being created. Is there a fix for this?

woodykiang

Member

Registered: 2009-01-25

Posts: 13

Re: I can't connect my Sony Ericsson w980

Hi,

After entirely update my system recently, this problem is still here... :-(

You can try this udev's patch on Ubuntu forum:
http://ubuntuforums.org/showthread.php?t=975622&page=3
but unfortunately it don't work for me.

I also tried modify the usb-storage module to add a unusual device entry for it, but still failed.
And now I just boot into Ubuntu live CD when I need to connect my mobile...

senaxo

Member

From: The Netherlands

Registered: 2009-08-03

Posts: 6

Re: I can't connect my Sony Ericsson w980

Hiya,

For me the udev patch also didn't work ... no other options, beside booting a Ubuntu live CD?

Last edited by senaxo (2009-08-05 14:35:33)

woodykiang

Member

Registered: 2009-01-25

Posts: 13

Re: I can't connect my Sony Ericsson w980

Um.. Yes, booting the Ubuntu live CD only in order to connect the phone is terrible for me too. Maybe if Virtualbox supports USB, it would be a handyer to boot a Ubuntu or Windows in it (but I'm not sure if they support that). If you have time and willing to try to fix this, maybe you should look at the usb-storage module :-) (adding a proper unusual entry? seeing what different between Ubuntu's and Archlinux's usb-storage module?).

olaf42

Member

Registered: 2009-08-07

Posts: 7

Re: I can't connect my Sony Ericsson w980

I got same promblem with SE C702. It might be something wrong with phone firmware.

senaxo

Member

From: The Netherlands

Registered: 2009-08-03

Posts: 6

Re: I can't connect my Sony Ericsson w980

Nah, it works under Ubuntu and other systems, so i guess the firmware of the phone is not the issue here ...

woodykiang

Member

Registered: 2009-01-25

Posts: 13

Re: I can't connect my Sony Ericsson w980

I've just updated my kernel to 2.6.30.4-1 and now the error message changed:

usb 1-5.2: new full speed USB device using ehci_hcd and address 39
usb 1-5.2: device descriptor read/64, error -32
usb 1-5.2: device descriptor read/64, error -32
usb 1-5.2: new full speed USB device using ehci_hcd and address 40
usb 1-5.2: device descriptor read/64, error -32
usb 1-5.2: device descriptor read/64, error -32
usb 1-5.2: new full speed USB device using ehci_hcd and address 41
usb 1-5.2: device not accepting address 41, error -32
usb 1-5.2: new full speed USB device using ehci_hcd and address 42
usb 1-5.2: device not accepting address 42, error -32
hub 1-5:1.0: unable to enumerate USB device on port 2

The error message became "familiar" which I have seen somewhere before...

b0uncyfr0

Member

Registered: 2008-05-11

Posts: 140

Re: I can't connect my Sony Ericsson w980

Did you guys ever get this working? I just ordered a W980, and im hoping it works. I dont want to get into windows just to copy files over to the phone.