You are not logged in.
- Topics: Active | Unanswered
#551 2009-12-31 03:27:51
- insanemal
- Member
- From: Brisbane/Australia
- Registered: 2009-05-05
- Posts: 140
Re: Discussion: the ati/radeon open source drivers & radeon repository
Hey, how do you disable the IRQ gear?
I tried removing radeon_ucode but that didn't do it.. Heck everything is still working fine.
My 3D performance has tanked hard in QuakeLive. It went from super-awesome to fail. So any ideas?
EDIT:
The reason things still worked with radeon_ucode removed is because i use early start... so it was in the initial ram drive. LULZ Reverting to 32.1-1 nukes the IRQ waits.
It isn't the IRQ waits causing the speed issue. Im going back to the stable stuff...
EDIT 2: The stable stuff doesn't give me anything.. With or without KMS. There is something really screwy with the 32.2-1 kernel and the "Stable" libs.
Oh well.. I'm on my slow bleeding edge drivers.. Mind you they are only slow in Quake.. lots of other things are really fast.. I would say the speed issue is due to the increase in the opengl level. Mesa 7.8 uses OpenGL 2.0 where as 7.7 seems to use 1.4 or something. I think this could be at fault. Anyway...
Big regression is big.
Last edited by insanemal (2009-12-31 06:27:00)
Offline
#552 2010-01-01 21:45:59
- descendent87
- Member
- Registered: 2009-07-23
- Posts: 105
Re: Discussion: the ati/radeon open source drivers & radeon repository
3D is working fine for me (haven't tried KMS) from the repo's, thinking about updating to git versions though, is there much of a difference at the moment? If so which is better (and safer) to go for kernel26-rc or kernel26-git?
Offline
#553 2010-01-02 00:08:34
- Perry3D
- Member
- Registered: 2008-03-20
- Posts: 553
Re: Discussion: the ati/radeon open source drivers & radeon repository
@descendent87: I prefer kernel26-git.
I take a look at the libdrm-PKGBUILD from extra. The radeon-experimental-api is disabled. Maybe this produce some problems with KMS enabled.
Offline
#554 2010-01-02 01:50:35
- Willem
- Member
- From: Wellington, NZ
- Registered: 2009-10-09
- Posts: 18
Re: Discussion: the ati/radeon open source drivers & radeon repository
I am using the all latest in stable and 3D is working fine.
I have an 4850 HD, is it possible to configure it with monitors with different resolutions?
Any pointers/links would be appreciated. I used to be able to do with the proprietary driver but can't get it to work with xf86-video-ati and still have 3D
Offline
#555 2010-01-02 03:10:35
- Perry3D
- Member
- Registered: 2008-03-20
- Posts: 553
Re: Discussion: the ati/radeon open source drivers & radeon repository
Did you try the xrandr tool?
Or the Display Settings from your DE?
Offline
#556 2010-01-02 20:56:02
- Willem
- Member
- From: Wellington, NZ
- Registered: 2009-10-09
- Posts: 18
Re: Discussion: the ati/radeon open source drivers & radeon repository
Perry3D: Thanks got it working http://bbs.archlinux.org/viewtopic.php?id=87901
Offline
#557 2010-01-05 14:11:41
- toroseduto
- Member
- Registered: 2009-11-17
- Posts: 1
Re: Discussion: the ati/radeon open source drivers & radeon repository
Hi, I followed the How To in the first post of this thread, I installed kernel26-git, libdrm-git, dri2proto-git, glrptoto-git , mesa-full and xf86-video-ati-git from AUR.
I don't use a xorg.conf file.
I have an ATI radeon HD3470 video card on an acer aspire 5920g notebook.
Without KMS it works fine, I can play nexuiz (although only with low effects).
When I enable KMS (creating /etc/modprobe.d/radeon.conf and writing "options radeon modeset=1" in it) 3d acceleration stops working:
[toroseduto@LHC ~]$ glxinfo |grep -i opengl
OpenGL vendor string: Mesa Project
OpenGL renderer string: Software Rasterizer
OpenGL version string: 2.1 Mesa 7.8-devel
OpenGL shading language version string: 1.20
OpenGL extensions:Here there is my /var/log/Xorg.0.log:
This is a pre-release version of the X server from The X.Org Foundation.
It is not supported in any way.
Bugs may be filed in the bugzilla at http://bugs.freedesktop.org/.
Select the "xorg" product for bugs you find in this release.
Before reporting bugs in pre-release versions please check the
latest version in the X.Org Foundation git repository.
See http://wiki.x.org/wiki/GitPage for git access instructions.
X.Org X Server 1.7.3.902 (1.7.4 RC 2)
Release Date: 2009-12-26
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.32-ARCH x86_64
Current Operating System: Linux LHC 2.6.33-rc2-00302-gc5974b8-dirty #1 SMP PREEMPT Tue Jan 5 13:30:40 CET 2010 x86_64
Kernel command line: root=/dev/sda2 ro
Build Date: 26 December 2009 02:34:45PM
Current version of pixman: 0.16.4
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Tue Jan 5 15:02:33 2010
(II) Loader magic: 0x7c09c0
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 6.0
X.Org XInput driver : 7.0
X.Org Server Extension : 2.0
(++) using VT number 7
(--) PCI:*(0:1:0:0) 1002:95c4:1025:0121 ATI Technologies Inc Mobility Radeon HD 3400 Series rev 0, Mem @ 0xd0000000/268435456, 0xf0200000/65536, I/O @ 0x00002000/256, BIOS @ 0x????????/131072
(==) Using default built-in configuration (30 lines)
(==) --- Start of built-in configuration ---
Section "Device"
Identifier "Builtin Default ati Device 0"
Driver "ati"
EndSection
Section "Screen"
Identifier "Builtin Default ati Screen 0"
Device "Builtin Default ati Device 0"
EndSection
Section "Device"
Identifier "Builtin Default vesa Device 0"
Driver "vesa"
EndSection
Section "Screen"
Identifier "Builtin Default vesa Screen 0"
Device "Builtin Default vesa Device 0"
EndSection
Section "Device"
Identifier "Builtin Default fbdev Device 0"
Driver "fbdev"
EndSection
Section "Screen"
Identifier "Builtin Default fbdev Screen 0"
Device "Builtin Default fbdev Device 0"
EndSection
Section "ServerLayout"
Identifier "Builtin Default Layout"
Screen "Builtin Default ati Screen 0"
Screen "Builtin Default vesa Screen 0"
Screen "Builtin Default fbdev Screen 0"
EndSection
(==) --- End of built-in configuration ---
(==) ServerLayout "Builtin Default Layout"
(**) |-->Screen "Builtin Default ati Screen 0" (0)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default ati Device 0"
(==) No monitor specified for screen "Builtin Default ati Screen 0".
Using a default monitor configuration.
(**) |-->Screen "Builtin Default vesa Screen 0" (1)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default vesa Device 0"
(==) No monitor specified for screen "Builtin Default vesa Screen 0".
Using a default monitor configuration.
(**) |-->Screen "Builtin Default fbdev Screen 0" (2)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default fbdev Device 0"
(==) No monitor specified for screen "Builtin Default fbdev Screen 0".
Using a default monitor configuration.
(==) Automatically adding devices
(==) Automatically enabling devices
(==) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/Type1
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) Cannot locate a core pointer device.
(II) Cannot locate a core keyboard device.
(II) The server relies on HAL to provide the list of input devices.
If no devices become available, reconfigure HAL or disable AutoAddDevices.
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions/libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions/libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.1.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "ati"
(II) Loading /usr/lib/xorg/modules/drivers/ati_drv.so
(II) Module ati: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 6.12.99
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 6.0
(II) LoadModule: "radeon"
(II) Loading /usr/lib/xorg/modules/drivers/radeon_drv.so
(II) Module radeon: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 6.12.99
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 6.0
(II) LoadModule: "vesa"
(II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
(II) Module vesa: vendor="X.Org Foundation"
compiled for 1.7.0.901, module version = 2.2.1
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 6.0
(II) LoadModule: "fbdev"
(WW) Warning, couldn't open module fbdev
(II) UnloadModule: "fbdev"
(EE) Failed to load module "fbdev" (module does not exist, 0)
(II) RADEON: Driver for ATI Radeon chipsets:
ATI Radeon Mobility X600 (M24) 3150 (PCIE), ATI FireMV 2400 (PCI),
ATI Radeon Mobility X300 (M24) 3152 (PCIE),
ATI FireGL M24 GL 3154 (PCIE), ATI Radeon X600 (RV380) 3E50 (PCIE),
ATI FireGL V3200 (RV380) 3E54 (PCIE), ATI Radeon IGP320 (A3) 4136,
ATI Radeon IGP330/340/350 (A4) 4137, ATI Radeon 9500 AD (AGP),
ATI Radeon 9500 AE (AGP), ATI Radeon 9600TX AF (AGP),
ATI FireGL Z1 AG (AGP), ATI Radeon 9800SE AH (AGP),
ATI Radeon 9800 AI (AGP), ATI Radeon 9800 AJ (AGP),
ATI FireGL X2 AK (AGP), ATI Radeon 9600 AP (AGP),
ATI Radeon 9600SE AQ (AGP), ATI Radeon 9600XT AR (AGP),
ATI Radeon 9600 AS (AGP), ATI FireGL T2 AT (AGP), ATI Radeon 9650,
ATI FireGL RV360 AV (AGP), ATI Radeon 7000 IGP (A4+) 4237,
ATI Radeon 8500 AIW BB (AGP), ATI Radeon 8500 AIW BC (AGP),
ATI Radeon IGP320M (U1) 4336, ATI Radeon IGP330M/340M/350M (U2) 4337,
ATI Radeon Mobility 7000 IGP 4437, ATI Radeon 9000/PRO If (AGP/PCI),
ATI Radeon 9000 Ig (AGP/PCI), ATI Radeon X800 (R420) JH (AGP),
ATI Radeon X800PRO (R420) JI (AGP),
ATI Radeon X800SE (R420) JJ (AGP), ATI Radeon X800 (R420) JK (AGP),
ATI Radeon X800 (R420) JL (AGP), ATI FireGL X3 (R420) JM (AGP),
ATI Radeon Mobility 9800 (M18) JN (AGP),
ATI Radeon X800 SE (R420) (AGP), ATI Radeon X800XT (R420) JP (AGP),
ATI Radeon X800 VE (R420) JT (AGP), ATI Radeon X850 (R480) (AGP),
ATI Radeon X850 XT (R480) (AGP), ATI Radeon X850 SE (R480) (AGP),
ATI Radeon X850 PRO (R480) (AGP), ATI Radeon X850 XT PE (R480) (AGP),
ATI Radeon Mobility M7 LW (AGP),
ATI Mobility FireGL 7800 M7 LX (AGP),
ATI Radeon Mobility M6 LY (AGP), ATI Radeon Mobility M6 LZ (AGP),
ATI FireGL Mobility 9000 (M9) Ld (AGP),
ATI Radeon Mobility 9000 (M9) Lf (AGP),
ATI Radeon Mobility 9000 (M9) Lg (AGP), ATI Radeon 9700 Pro ND (AGP),
ATI Radeon 9700/9500Pro NE (AGP), ATI Radeon 9600TX NF (AGP),
ATI FireGL X1 NG (AGP), ATI Radeon 9800PRO NH (AGP),
ATI Radeon 9800 NI (AGP), ATI FireGL X2 NK (AGP),
ATI Radeon 9800XT NJ (AGP),
ATI Radeon Mobility 9600/9700 (M10/M11) NP (AGP),
ATI Radeon Mobility 9600 (M10) NQ (AGP),
ATI Radeon Mobility 9600 (M11) NR (AGP),
ATI Radeon Mobility 9600 (M10) NS (AGP),
ATI FireGL Mobility T2 (M10) NT (AGP),
ATI FireGL Mobility T2e (M11) NV (AGP), ATI Radeon QD (AGP),
ATI Radeon QE (AGP), ATI Radeon QF (AGP), ATI Radeon QG (AGP),
ATI FireGL 8700/8800 QH (AGP), ATI Radeon 8500 QL (AGP),
ATI Radeon 9100 QM (AGP), ATI Radeon 7500 QW (AGP/PCI),
ATI Radeon 7500 QX (AGP/PCI), ATI Radeon VE/7000 QY (AGP/PCI),
ATI Radeon VE/7000 QZ (AGP/PCI), ATI ES1000 515E (PCI),
ATI Radeon Mobility X300 (M22) 5460 (PCIE),
ATI Radeon Mobility X600 SE (M24C) 5462 (PCIE),
ATI FireGL M22 GL 5464 (PCIE), ATI Radeon X800 (R423) UH (PCIE),
ATI Radeon X800PRO (R423) UI (PCIE),
ATI Radeon X800LE (R423) UJ (PCIE),
ATI Radeon X800SE (R423) UK (PCIE),
ATI Radeon X800 XTP (R430) (PCIE), ATI Radeon X800 XL (R430) (PCIE),
ATI Radeon X800 SE (R430) (PCIE), ATI Radeon X800 (R430) (PCIE),
ATI FireGL V7100 (R423) (PCIE), ATI FireGL V5100 (R423) UQ (PCIE),
ATI FireGL unknown (R423) UR (PCIE),
ATI FireGL unknown (R423) UT (PCIE),
ATI Mobility FireGL V5000 (M26) (PCIE),
ATI Mobility FireGL V5000 (M26) (PCIE),
ATI Mobility Radeon X700 XL (M26) (PCIE),
ATI Mobility Radeon X700 (M26) (PCIE),
ATI Mobility Radeon X700 (M26) (PCIE),
ATI Radeon X550XTX 5657 (PCIE), ATI Radeon 9100 IGP (A5) 5834,
ATI Radeon Mobility 9100 IGP (U3) 5835,
ATI Radeon XPRESS 200 5954 (PCIE),
ATI Radeon XPRESS 200M 5955 (PCIE), ATI Radeon 9250 5960 (AGP),
ATI Radeon 9200 5961 (AGP), ATI Radeon 9200 5962 (AGP),
ATI Radeon 9200SE 5964 (AGP), ATI FireMV 2200 (PCI),
ATI ES1000 5969 (PCI), ATI Radeon XPRESS 200 5974 (PCIE),
ATI Radeon XPRESS 200M 5975 (PCIE),
ATI Radeon XPRESS 200 5A41 (PCIE),
ATI Radeon XPRESS 200M 5A42 (PCIE),
ATI Radeon XPRESS 200 5A61 (PCIE),
ATI Radeon XPRESS 200M 5A62 (PCIE),
ATI Radeon X300 (RV370) 5B60 (PCIE),
ATI Radeon X600 (RV370) 5B62 (PCIE),
ATI Radeon X550 (RV370) 5B63 (PCIE),
ATI FireGL V3100 (RV370) 5B64 (PCIE),
ATI FireMV 2200 PCIE (RV370) 5B65 (PCIE),
ATI Radeon Mobility 9200 (M9+) 5C61 (AGP),
ATI Radeon Mobility 9200 (M9+) 5C63 (AGP),
ATI Mobility Radeon X800 XT (M28) (PCIE),
ATI Mobility FireGL V5100 (M28) (PCIE),
ATI Mobility Radeon X800 (M28) (PCIE), ATI Radeon X850 5D4C (PCIE),
ATI Radeon X850 XT PE (R480) (PCIE),
ATI Radeon X850 SE (R480) (PCIE), ATI Radeon X850 PRO (R480) (PCIE),
ATI unknown Radeon / FireGL (R480) 5D50 (PCIE),
ATI Radeon X850 XT (R480) (PCIE),
ATI Radeon X800XT (R423) 5D57 (PCIE),
ATI FireGL V5000 (RV410) (PCIE), ATI Radeon X700 XT (RV410) (PCIE),
ATI Radeon X700 PRO (RV410) (PCIE),
ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X700 (RV410) (PCIE),
ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X1800,
ATI Mobility Radeon X1800 XT, ATI Mobility Radeon X1800,
ATI Mobility FireGL V7200, ATI FireGL V7200, ATI FireGL V5300,
ATI Mobility FireGL V7100, ATI Radeon X1800, ATI Radeon X1800,
ATI Radeon X1800, ATI Radeon X1800, ATI Radeon X1800,
ATI FireGL V7300, ATI FireGL V7350, ATI Radeon X1600, ATI RV505,
ATI Radeon X1300/X1550, ATI Radeon X1550, ATI M54-GL,
ATI Mobility Radeon X1400, ATI Radeon X1300/X1550,
ATI Radeon X1550 64-bit, ATI Mobility Radeon X1300,
ATI Mobility Radeon X1300, ATI Mobility Radeon X1300,
ATI Mobility Radeon X1300, ATI Radeon X1300, ATI Radeon X1300,
ATI RV505, ATI RV505, ATI FireGL V3300, ATI FireGL V3350,
ATI Radeon X1300, ATI Radeon X1550 64-bit, ATI Radeon X1300/X1550,
ATI Radeon X1600, ATI Radeon X1300/X1550, ATI Mobility Radeon X1450,
ATI Radeon X1300/X1550, ATI Mobility Radeon X2300,
ATI Mobility Radeon X2300, ATI Mobility Radeon X1350,
ATI Mobility Radeon X1350, ATI Mobility Radeon X1450,
ATI Radeon X1300, ATI Radeon X1550, ATI Mobility Radeon X1350,
ATI FireMV 2250, ATI Radeon X1550 64-bit, ATI Radeon X1600,
ATI Radeon X1650, ATI Radeon X1600, ATI Radeon X1600,
ATI Mobility FireGL V5200, ATI Mobility Radeon X1600,
ATI Radeon X1650, ATI Radeon X1650, ATI Radeon X1600,
ATI Radeon X1300 XT/X1600 Pro, ATI FireGL V3400,
ATI Mobility FireGL V5250, ATI Mobility Radeon X1700,
ATI Mobility Radeon X1700 XT, ATI FireGL V5200,
ATI Mobility Radeon X1700, ATI Radeon X2300HD,
ATI Mobility Radeon HD 2300, ATI Mobility Radeon HD 2300,
ATI Radeon X1950, ATI Radeon X1900, ATI Radeon X1950,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI AMD Stream Processor, ATI Radeon X1900, ATI Radeon X1950,
ATI RV560, ATI RV560, ATI Mobility Radeon X1900, ATI RV560,
ATI Radeon X1950 GT, ATI RV570, ATI RV570, ATI FireGL V7400,
ATI RV560, ATI Radeon X1650, ATI Radeon X1650, ATI RV560,
ATI Radeon 9100 PRO IGP 7834, ATI Radeon Mobility 9200 IGP 7835,
ATI Radeon X1200, ATI Radeon X1200, ATI Radeon X1200,
ATI Radeon X1200, ATI Radeon X1200, ATI RS740, ATI RS740M, ATI RS740,
ATI RS740M, ATI Radeon HD 2900 XT, ATI Radeon HD 2900 XT,
ATI Radeon HD 2900 XT, ATI Radeon HD 2900 Pro, ATI Radeon HD 2900 GT,
ATI FireGL V8650, ATI FireGL V8600, ATI FireGL V7600,
ATI Radeon 4800 Series, ATI Radeon HD 4870 x2,
ATI Radeon 4800 Series, ATI Radeon HD 4850 x2,
ATI FirePro V8750 (FireGL), ATI FirePro V7760 (FireGL),
ATI Mobility RADEON HD 4850, ATI Mobility RADEON HD 4850 X2,
ATI Radeon 4800 Series, ATI FirePro RV770, AMD FireStream 9270,
AMD FireStream 9250, ATI FirePro V8700 (FireGL),
ATI Mobility RADEON HD 4870, ATI Mobility RADEON M98,
ATI Radeon 4800 Series, ATI Radeon 4800 Series, ATI FirePro M7750,
ATI M98, ATI M98, ATI M98, ATI Mobility Radeon HD 4650,
ATI Radeon RV730 (AGP), ATI Mobility Radeon HD 4670,
ATI FirePro M5750, ATI Radeon RV730 (AGP),
ATI RV730XT [Radeon HD 4670], ATI RADEON E4600,
ATI Radeon HD 4600 Series, ATI RV730 PRO [Radeon HD 4650],
ATI FirePro V7750 (FireGL), ATI FirePro V5700 (FireGL),
ATI FirePro V3750 (FireGL), ATI Mobility Radeon HD 4830,
ATI Mobility Radeon HD 4850, ATI FirePro M7740, ATI RV740,
ATI Radeon HD 4770, ATI Radeon HD 4700 Series, ATI Radeon HD 4770,
ATI FirePro M5750, ATI RV610, ATI Radeon HD 2400 XT,
ATI Radeon HD 2400 Pro, ATI Radeon HD 2400 PRO AGP, ATI FireGL V4000,
ATI RV610, ATI Radeon HD 2350, ATI Mobility Radeon HD 2400 XT,
ATI Mobility Radeon HD 2400, ATI RADEON E2400, ATI RV610,
ATI FireMV 2260, ATI RV670, ATI Radeon HD3870,
ATI Mobility Radeon HD 3850, ATI Radeon HD3850,
ATI Mobility Radeon HD 3850 X2, ATI RV670,
ATI Mobility Radeon HD 3870, ATI Mobility Radeon HD 3870 X2,
ATI Radeon HD3870 X2, ATI FireGL V7700, ATI Radeon HD3850,
ATI Radeon HD3690, AMD Firestream 9170, ATI Radeon HD 4550,
ATI Radeon RV710, ATI Radeon RV710, ATI Radeon HD 4350,
ATI Mobility Radeon 4300 Series, ATI Mobility Radeon 4500 Series,
ATI Mobility Radeon 4500 Series, ATI FirePro RG220, ATI RV630,
ATI Mobility Radeon HD 2600, ATI Mobility Radeon HD 2600 XT,
ATI Radeon HD 2600 XT AGP, ATI Radeon HD 2600 Pro AGP,
ATI Radeon HD 2600 XT, ATI Radeon HD 2600 Pro, ATI Gemini RV630,
ATI Gemini Mobility Radeon HD 2600 XT, ATI FireGL V5600,
ATI FireGL V3600, ATI Radeon HD 2600 LE,
ATI Mobility FireGL Graphics Processor, ATI Radeon RV710,
ATI Radeon HD 3470, ATI Mobility Radeon HD 3430,
ATI Mobility Radeon HD 3400 Series, ATI Radeon HD 3450,
ATI Radeon HD 3450, ATI Radeon HD 3430, ATI Radeon HD 3450,
ATI FirePro V3700, ATI FireMV 2450, ATI FireMV 2260, ATI FireMV 2260,
ATI Radeon HD 3600 Series, ATI Radeon HD 3650 AGP,
ATI Radeon HD 3600 PRO, ATI Radeon HD 3600 XT,
ATI Radeon HD 3600 PRO, ATI Mobility Radeon HD 3650,
ATI Mobility Radeon HD 3670, ATI Mobility FireGL V5700,
ATI Mobility FireGL V5725, ATI Radeon HD 3200 Graphics,
ATI Radeon 3100 Graphics, ATI Radeon HD 3200 Graphics,
ATI Radeon 3100 Graphics, ATI Radeon HD 3300 Graphics,
ATI Radeon HD 3200 Graphics, ATI Radeon 3000 Graphics,
ATI Radeon HD 4200, ATI Radeon 4100, ATI Mobility Radeon HD 4200,
ATI Mobility Radeon 4100, ATI RS880
(II) VESA: driver for VESA chipsets: vesa
(II) Primary Device is: PCI 01@00:00:0
(II) [KMS] drm report modesetting isn't supported.
(WW) Falling back to old probe method for vesa
(WW) VGA arbiter: cannot open kernel arbiter, no multi-card support
(II) RADEON(0): TOTO SAYS 00000000f0200000
(II) RADEON(0): MMIO registers at 0x00000000f0200000: size 64KB
(II) RADEON(0): PCI bus 1 card 0 func 0
(II) RADEON(0): Creating default Display subsection in Screen section
"Builtin Default ati Screen 0" for depth/fbbpp 24/32
(==) RADEON(0): Depth 24, (--) framebuffer bpp 32
(II) RADEON(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
(==) RADEON(0): Default visual is TrueColor
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules/libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 0.1.0
ABI class: X.Org Video Driver, version 6.0
(II) RADEON(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(==) RADEON(0): RGB weight 888
(II) RADEON(0): Using 8 bits per RGB (8 bit DAC)
(--) RADEON(0): Chipset: "ATI Mobility Radeon HD 3400 Series" (ChipID = 0x95c4)
(--) RADEON(0): Linear framebuffer at 0x00000000d0000000
(II) RADEON(0): PCIE card detected
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib/xorg/modules/libint10.so
(II) Module int10: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.0.0
ABI class: X.Org Video Driver, version 6.0
(II) RADEON(0): initializing int10
(II) RADEON(0): Primary V_BIOS segment is: 0xc000
(II) RADEON(0): ATOM BIOS detected
(II) RADEON(0): ATOM BIOS Rom:
SubsystemVendorID: 0x1002 SubsystemID: 0x95c4
IOBaseAddress: 0x2000
Filename: BR27808.001
BIOS Bootup Message:
Acer_M82XT_MXM M82 GDDR2_32Mx16 64bit 256MB 680e/500m
(II) RADEON(0): Framebuffer space used by Firmware (kb): 16
(II) RADEON(0): Start of VRAM area used by Firmware: 0xfffc000
(II) RADEON(0): AtomBIOS requests 16kB of VRAM scratch space
(II) RADEON(0): AtomBIOS VRAM scratch base: 0xfffc000
(II) RADEON(0): Cannot get VRAM scratch space. Allocating in main memory instead
(II) RADEON(0): Default Engine Clock: 680000
(II) RADEON(0): Default Memory Clock: 500000
(II) RADEON(0): Maximum Pixel ClockPLL Frequency Output: 1200000
(II) RADEON(0): Minimum Pixel ClockPLL Frequency Output: 0
(II) RADEON(0): Maximum Pixel ClockPLL Frequency Input: 13500
(II) RADEON(0): Minimum Pixel ClockPLL Frequency Input: 1000
(II) RADEON(0): Maximum Pixel Clock: 400000
(II) RADEON(0): Reference Clock: 27000
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (No such device or address)
drmOpenDevice: open result is -1, (No such device or address)
drmOpenDevice: Open failed
[drm] failed to load kernel module "radeon"
(EE) RADEON(0): [dri] RADEONDRIGetVersion failed to open the DRM
[dri] Disabling DRI.
(II) RADEON(0): using shadow framebuffer
(II) Loading sub module "shadow"
(II) LoadModule: "shadow"
(II) Loading /usr/lib/xorg/modules/libshadow.so
(II) Module shadow: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.1.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) RADEON(0): Detected total video RAM=262144K, accessible=262144K (PCI BAR=262144K)
(--) RADEON(0): Mapped VideoRAM: 262144 kByte (64 bit DDR SDRAM)
(II) RADEON(0): Color tiling disabled
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Module "i2c" already built-in
(II) RADEON(0): PLL parameters: rf=2700 rd=12 min=90000 max=120000; xclk=40000
(WW) RADEON(0): LVDS Info:
XRes: 1280, YRes: 800, DotClock: 68940
HBlank: 128, HOverPlus: 16, HSyncWidth: 48
VBlank: 16, VOverPlus: 1, VSyncWidth: 3
(II) RADEON(0): Output LVDS has no monitor section
(II) RADEON(0): I2C bus "LVDS" initialized.
(II) RADEON(0): Output HDMI-0 has no monitor section
(II) RADEON(0): I2C bus "HDMI-0" initialized.
(II) RADEON(0): Output DVI-0 has no monitor section
(II) RADEON(0): I2C bus "DVI-0" initialized.
(II) RADEON(0): Output VGA-0 has no monitor section
(II) RADEON(0): I2C bus "VGA-0" initialized.
(II) RADEON(0): Port0:
XRANDR name: LVDS
Connector: LVDS
LCD1: INTERNAL_KLDSCP_LVTMA
DDC reg: 0x7f68
(II) RADEON(0): Port1:
XRANDR name: HDMI-0
Connector: HDMI-A
DFP1: INTERNAL_UNIPHY
DDC reg: 0x7e60
(II) RADEON(0): Port2:
XRANDR name: DVI-0
Connector: DVI-I
DFP1: INTERNAL_UNIPHY
DDC reg: 0x7e60
(II) RADEON(0): Port3:
XRANDR name: VGA-0
Connector: VGA
CRT1: INTERNAL_KLDSCP_DAC1
DDC reg: 0x7e40
(II) RADEON(0): I2C device "LVDS:ddc2" registered at address 0xA0.
(II) RADEON(0): EDID vendor "SEC", prod id 14661
(II) RADEON(0): Printing DDC gathered Modelines:
(II) RADEON(0): Modeline "1280x800"x0.0 68.94 1280 1296 1344 1408 800 801 804 816 -hsync -vsync (49.0 kHz)
(II) RADEON(0): Output: LVDS, Detected Monitor Type: 2
(II) RADEON(0): EDID data from the display on output: LVDS ----------------------
(II) RADEON(0): Manufacturer: SEC Model: 3945 Serial#: 0
(II) RADEON(0): Year: 2007 Week: 0
(II) RADEON(0): EDID Version: 1.3
(II) RADEON(0): Digital Display Input
(II) RADEON(0): Max Image Size [cm]: horiz.: 33 vert.: 21
(II) RADEON(0): Gamma: 2.20
(II) RADEON(0): No DPMS capabilities specified
(II) RADEON(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
(II) RADEON(0): First detailed timing is preferred mode
(II) RADEON(0): redX: 0.580 redY: 0.340 greenX: 0.310 greenY: 0.550
(II) RADEON(0): blueX: 0.155 blueY: 0.155 whiteX: 0.313 whiteY: 0.329
(II) RADEON(0): Manufacturer's mask: 0
(II) RADEON(0): Supported detailed timing:
(II) RADEON(0): clock: 68.9 MHz Image Size: 331 x 207 mm
(II) RADEON(0): h_active: 1280 h_sync: 1296 h_sync_end 1344 h_blank_end 1408 h_border: 0
(II) RADEON(0): v_active: 800 v_sync: 801 v_sync_end 804 v_blanking: 816 v_border: 0
(II) RADEON(0): Unknown vendor-specific block f
(II) RADEON(0): SAMSUNG
(II) RADEON(0): 154AT01-001
(II) RADEON(0): EDID (in hex):
(II) RADEON(0): 00ffffffffffff004ca3453900000000
(II) RADEON(0): 00110103802115780a87f594574f8c27
(II) RADEON(0): 27505400000001010101010101010101
(II) RADEON(0): 010101010101ee1a0080502010301030
(II) RADEON(0): 13004bcf100000190000000f00000000
(II) RADEON(0): 00000000002387026400000000fe0053
(II) RADEON(0): 414d53554e470a2020202020000000fe
(II) RADEON(0): 00313534415430312d3030310a2000df
finished output detect: 0
(II) RADEON(0): I2C device "HDMI-0:ddc2" registered at address 0xA0.
(II) RADEON(0): Output: HDMI-0, Detected Monitor Type: 0
finished output detect: 1
(II) RADEON(0): I2C device "DVI-0:ddc2" registered at address 0xA0.
(II) RADEON(0): Output: DVI-0, Detected Monitor Type: 0
Unhandled monitor type 0
finished output detect: 2
(II) RADEON(0): I2C device "VGA-0:ddc2" registered at address 0xA0.
Dac detection success
(II) RADEON(0): Output: VGA-0, Detected Monitor Type: 0
finished output detect: 3
finished all detect
before xf86InitialConfiguration
(II) RADEON(0): EDID vendor "SEC", prod id 14661
(II) RADEON(0): Printing DDC gathered Modelines:
(II) RADEON(0): Modeline "1280x800"x0.0 68.94 1280 1296 1344 1408 800 801 804 816 -hsync -vsync (49.0 kHz)
(II) RADEON(0): Output: LVDS, Detected Monitor Type: 2
(II) RADEON(0): EDID data from the display on output: LVDS ----------------------
(II) RADEON(0): Manufacturer: SEC Model: 3945 Serial#: 0
(II) RADEON(0): Year: 2007 Week: 0
(II) RADEON(0): EDID Version: 1.3
(II) RADEON(0): Digital Display Input
(II) RADEON(0): Max Image Size [cm]: horiz.: 33 vert.: 21
(II) RADEON(0): Gamma: 2.20
(II) RADEON(0): No DPMS capabilities specified
(II) RADEON(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
(II) RADEON(0): First detailed timing is preferred mode
(II) RADEON(0): redX: 0.580 redY: 0.340 greenX: 0.310 greenY: 0.550
(II) RADEON(0): blueX: 0.155 blueY: 0.155 whiteX: 0.313 whiteY: 0.329
(II) RADEON(0): Manufacturer's mask: 0
(II) RADEON(0): Supported detailed timing:
(II) RADEON(0): clock: 68.9 MHz Image Size: 331 x 207 mm
(II) RADEON(0): h_active: 1280 h_sync: 1296 h_sync_end 1344 h_blank_end 1408 h_border: 0
(II) RADEON(0): v_active: 800 v_sync: 801 v_sync_end 804 v_blanking: 816 v_border: 0
(II) RADEON(0): Unknown vendor-specific block f
(II) RADEON(0): SAMSUNG
(II) RADEON(0): 154AT01-001
(II) RADEON(0): EDID (in hex):
(II) RADEON(0): 00ffffffffffff004ca3453900000000
(II) RADEON(0): 00110103802115780a87f594574f8c27
(II) RADEON(0): 27505400000001010101010101010101
(II) RADEON(0): 010101010101ee1a0080502010301030
(II) RADEON(0): 13004bcf100000190000000f00000000
(II) RADEON(0): 00000000002387026400000000fe0053
(II) RADEON(0): 414d53554e470a2020202020000000fe
(II) RADEON(0): 00313534415430312d3030310a2000df
(II) RADEON(0): EDID vendor "SEC", prod id 14661
(II) RADEON(0): Output: HDMI-0, Detected Monitor Type: 0
(II) RADEON(0): Output: DVI-0, Detected Monitor Type: 0
Unhandled monitor type 0
Dac detection success
(II) RADEON(0): Output: VGA-0, Detected Monitor Type: 0
(II) RADEON(0): Output LVDS connected
(II) RADEON(0): Output HDMI-0 disconnected
(II) RADEON(0): Output DVI-0 disconnected
(II) RADEON(0): Output VGA-0 disconnected
(II) RADEON(0): Using exact sizes for initial modes
(II) RADEON(0): Output LVDS using initial mode 1280x800
(II) RADEON(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
(**) RADEON(0): Display dimensions: (330, 210) mm
(**) RADEON(0): DPI set to (98, 154)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules/libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(!!) RADEON(0): MergedFB support has been removed and replaced with xrandr 1.2 support
(II) UnloadModule: "vesa"
(II) Unloading /usr/lib/xorg/modules/drivers/vesa_drv.so
(--) Depth 24 pixmap format is 32 bpp
(II) RADEON(0): RADEONScreenInit d0000000 0 0
Output DIG0 transmitter setup success
Blank CRTC 0 success
Disable CRTC memreq 0 success
Disable CRTC 0 success
Blank CRTC 1 success
Disable CRTC memreq 1 success
Disable CRTC 1 success
(II) RADEON(0): Dynamic Power Management Disabled
mc fb loc is 00df00d0
(II) RADEON(0): RADEONInitMemoryMap() :
(II) RADEON(0): mem_size : 0x10000000
(II) RADEON(0): MC_FB_LOCATION : 0x00df00d0
(II) RADEON(0): MC_AGP_LOCATION : 0x003f0000
(II) RADEON(0): Depth moves disabled by default
(II) RADEON(0): Memory manager initialized to (0,0) (1280,8191)
(II) RADEON(0): Reserved area from (0,1280) to (1280,1282)
(II) RADEON(0): Largest offscreen area available: 1280 x 6909
(II) RADEON(0): RADEONRestoreMemMapRegisters() :
(II) RADEON(0): MC_FB_LOCATION : 0x00df00d0 0x00df00d0
(II) RADEON(0): MC_AGP_LOCATION : 0x003f0000
(==) RADEON(0): Backing store disabled
(WW) RADEON(0): Direct rendering disabled
(EE) RADEON(0): Acceleration initialization failed
(II) RADEON(0): Acceleration disabled
(==) RADEON(0): DPMS enabled
(==) RADEON(0): Silken mouse enabled
(II) RADEON(0): Will use 32 kb for hardware cursor 0 at offset 0x00643000
(II) RADEON(0): Will use 32 kb for hardware cursor 1 at offset 0x00648000
(II) RADEON(0): Largest offscreen area available: 1280 x 6901
(II) RADEON(0): Textured video requires CP on R5xx/R6xx/R7xx/IGP
Output DIG0 transmitter setup success
Output CRT1 disable success
Blank CRTC 0 success
Disable CRTC memreq 0 success
Disable CRTC 0 success
Blank CRTC 1 success
Disable CRTC memreq 1 success
Disable CRTC 1 success
Output DIG0 transmitter setup success
Blank CRTC 0 success
Disable CRTC memreq 0 success
Disable CRTC 0 success
Mode 1280x800 - 1408 816 10
(II) RADEON(0): RADEONRestoreMemMapRegisters() :
(II) RADEON(0): MC_FB_LOCATION : 0x00df00d0 0x00df00d0
(II) RADEON(0): MC_AGP_LOCATION : 0x003f0000
before 6894
after 6894
ffreq: 68940.000000
best_freq: 68940
best_feedback_div: 86.8
best_ref_div: 2
best_post_div: 17
(II) RADEON(0): crtc(0) Clock: mode 68940, PLL 68940
(II) RADEON(0): crtc(0) PLL : refdiv 2, fbdiv 0x56(86), fracfbdiv 8, pdiv 17
Set CRTC 0 PLL success
Set CRTC Timing success
Set CRTC 0 Overscan success
Not using RMX
scaler 0 setup success
Set CRTC 0 Source success
crtc 0 YUV disable setup success
Output DIG0 transmitter setup success
Output DIG2 encoder setup success
Output DIG2 encoder setup success
Output DIG0 transmitter setup success
Output DIG0 transmitter setup success
Output DIG0 transmitter setup success
Output DIG0 transmitter setup success
Enable CRTC 0 success
Enable CRTC memreq 0 success
Unblank CRTC 0 success
Output CRT1 disable success
Blank CRTC 1 success
Disable CRTC memreq 1 success
Disable CRTC 1 success
(II) RADEON(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(--) RandR disabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) AIGLX: Screen 0 is not DRI2 capable
(II) AIGLX: Screen 0 is not DRI capable
(II) AIGLX: Loaded and initialized /usr/lib/xorg/modules/dri/swrast_dri.so
(II) GLX: Initialized DRISWRAST GL provider for screen 0
(II) RADEON(0): Setting screen physical size to 338 x 211
(II) config/hal: Adding input device SynPS/2 Synaptics TouchPad
(II) LoadModule: "synaptics"
(II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
(II) Module synaptics: vendor="X.Org Foundation"
compiled for 1.7.3.901, module version = 1.2.1
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 7.0
(II) Synaptics touchpad driver version 1.2.1
(**) Option "Device" "/dev/input/event12"
(II) SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5472
(II) SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4448
(II) SynPS/2 Synaptics TouchPad: pressure range 0 - 255
(II) SynPS/2 Synaptics TouchPad: finger width range 0 - 0
(II) SynPS/2 Synaptics TouchPad: buttons: left right
(**) Option "TapButton1" "1"
(**) Option "TapButton2" "2"
(**) Option "TapButton3" "3"
(--) SynPS/2 Synaptics TouchPad: touchpad found
(**) SynPS/2 Synaptics TouchPad: always reports core events
(II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD)
(**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
(**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 0
(--) SynPS/2 Synaptics TouchPad: touchpad found
(II) config/hal: Adding input device Acer CrystalEye webcam
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
compiled for 1.7.3, module version = 2.3.2
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 7.0
(**) Acer CrystalEye webcam: always reports core events
(**) Acer CrystalEye webcam: Device: "/dev/input/event11"
(II) Acer CrystalEye webcam: Found keys
(II) Acer CrystalEye webcam: Configuring as keyboard
(II) XINPUT: Adding extended input device "Acer CrystalEye webcam" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Logitech USB-PS/2 Optical Mouse
(**) Logitech USB-PS/2 Optical Mouse: always reports core events
(**) Logitech USB-PS/2 Optical Mouse: Device: "/dev/input/event10"
(II) Logitech USB-PS/2 Optical Mouse: Found 12 mouse buttons
(II) Logitech USB-PS/2 Optical Mouse: Found scroll wheel(s)
(II) Logitech USB-PS/2 Optical Mouse: Found relative axes
(II) Logitech USB-PS/2 Optical Mouse: Found x and y relative axes
(II) Logitech USB-PS/2 Optical Mouse: Configuring as mouse
(**) Logitech USB-PS/2 Optical Mouse: YAxisMapping: buttons 4 and 5
(**) Logitech USB-PS/2 Optical Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Logitech USB-PS/2 Optical Mouse" (type: MOUSE)
(**) Logitech USB-PS/2 Optical Mouse: (accel) keeping acceleration scheme 1
(**) Logitech USB-PS/2 Optical Mouse: (accel) acceleration profile 0
(II) Logitech USB-PS/2 Optical Mouse: initialized for relative axes.
(II) config/hal: Adding input device SynPS/2 Synaptics TouchPad
(II) Synaptics touchpad driver version 1.2.1
(**) Option "Device" "/dev/input/event8"
(II) SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5472
(II) SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4448
(II) SynPS/2 Synaptics TouchPad: pressure range 0 - 255
(II) SynPS/2 Synaptics TouchPad: finger width range 0 - 0
(II) SynPS/2 Synaptics TouchPad: buttons: left right
(**) Option "TapButton1" "1"
(**) Option "TapButton2" "2"
(**) Option "TapButton3" "3"
(--) SynPS/2 Synaptics TouchPad: touchpad found
(**) SynPS/2 Synaptics TouchPad: always reports core events
(II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD)
(**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
(**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 0
(--) SynPS/2 Synaptics TouchPad: touchpad found
(II) config/hal: Adding input device AT Translated Set 2 keyboard
(**) AT Translated Set 2 keyboard: always reports core events
(**) AT Translated Set 2 keyboard: Device: "/dev/input/event1"
(II) AT Translated Set 2 keyboard: Found keys
(II) AT Translated Set 2 keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Video Bus
(**) Video Bus: always reports core events
(**) Video Bus: Device: "/dev/input/event7"
(II) Video Bus: Found keys
(II) Video Bus: Configuring as keyboard
(II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Power Button
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event3"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Sleep Button
(**) Sleep Button: always reports core events
(**) Sleep Button: Device: "/dev/input/event4"
(II) Sleep Button: Found keys
(II) Sleep Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Power Button
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event5"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Macintosh mouse button emulation
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event0"
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Found relative axes
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Configuring as mouse
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
(**) Macintosh mouse button emulation: (accel) acceleration profile 0
(II) Macintosh mouse button emulation: initialized for relative axes.
(II) RADEON(0): EDID vendor "SEC", prod id 14661
(II) RADEON(0): Printing DDC gathered Modelines:
(II) RADEON(0): Modeline "1280x800"x0.0 68.94 1280 1296 1344 1408 800 801 804 816 -hsync -vsync (49.0 kHz)
(II) RADEON(0): Output: LVDS, Detected Monitor Type: 2
(II) RADEON(0): EDID data from the display on output: LVDS ----------------------
(II) RADEON(0): Manufacturer: SEC Model: 3945 Serial#: 0
(II) RADEON(0): Year: 2007 Week: 0
(II) RADEON(0): EDID Version: 1.3
(II) RADEON(0): Digital Display Input
(II) RADEON(0): Max Image Size [cm]: horiz.: 33 vert.: 21
(II) RADEON(0): Gamma: 2.20
(II) RADEON(0): No DPMS capabilities specified
(II) RADEON(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
(II) RADEON(0): First detailed timing is preferred mode
(II) RADEON(0): redX: 0.580 redY: 0.340 greenX: 0.310 greenY: 0.550
(II) RADEON(0): blueX: 0.155 blueY: 0.155 whiteX: 0.313 whiteY: 0.329
(II) RADEON(0): Manufacturer's mask: 0
(II) RADEON(0): Supported detailed timing:
(II) RADEON(0): clock: 68.9 MHz Image Size: 331 x 207 mm
(II) RADEON(0): h_active: 1280 h_sync: 1296 h_sync_end 1344 h_blank_end 1408 h_border: 0
(II) RADEON(0): v_active: 800 v_sync: 801 v_sync_end 804 v_blanking: 816 v_border: 0
(II) RADEON(0): Unknown vendor-specific block f
(II) RADEON(0): SAMSUNG
(II) RADEON(0): 154AT01-001
(II) RADEON(0): EDID (in hex):
(II) RADEON(0): 00ffffffffffff004ca3453900000000
(II) RADEON(0): 00110103802115780a87f594574f8c27
(II) RADEON(0): 27505400000001010101010101010101
(II) RADEON(0): 010101010101ee1a0080502010301030
(II) RADEON(0): 13004bcf100000190000000f00000000
(II) RADEON(0): 00000000002387026400000000fe0053
(II) RADEON(0): 414d53554e470a2020202020000000fe
(II) RADEON(0): 00313534415430312d3030310a2000df
(II) RADEON(0): EDID vendor "SEC", prod id 14661
(II) RADEON(0): Output: HDMI-0, Detected Monitor Type: 0
(II) RADEON(0): Output: DVI-0, Detected Monitor Type: 0
Unhandled monitor type 0
Dac detection success
(II) RADEON(0): Output: VGA-0, Detected Monitor Type: 0
(II) RADEON(0): EDID vendor "SEC", prod id 14661
(II) RADEON(0): Printing DDC gathered Modelines:
(II) RADEON(0): Modeline "1280x800"x0.0 68.94 1280 1296 1344 1408 800 801 804 816 -hsync -vsync (49.0 kHz)
(II) RADEON(0): Output: LVDS, Detected Monitor Type: 2
(II) RADEON(0): EDID data from the display on output: LVDS ----------------------
(II) RADEON(0): Manufacturer: SEC Model: 3945 Serial#: 0
(II) RADEON(0): Year: 2007 Week: 0
(II) RADEON(0): EDID Version: 1.3
(II) RADEON(0): Digital Display Input
(II) RADEON(0): Max Image Size [cm]: horiz.: 33 vert.: 21
(II) RADEON(0): Gamma: 2.20
(II) RADEON(0): No DPMS capabilities specified
(II) RADEON(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
(II) RADEON(0): First detailed timing is preferred mode
(II) RADEON(0): redX: 0.580 redY: 0.340 greenX: 0.310 greenY: 0.550
(II) RADEON(0): blueX: 0.155 blueY: 0.155 whiteX: 0.313 whiteY: 0.329
(II) RADEON(0): Manufacturer's mask: 0
(II) RADEON(0): Supported detailed timing:
(II) RADEON(0): clock: 68.9 MHz Image Size: 331 x 207 mm
(II) RADEON(0): h_active: 1280 h_sync: 1296 h_sync_end 1344 h_blank_end 1408 h_border: 0
(II) RADEON(0): v_active: 800 v_sync: 801 v_sync_end 804 v_blanking: 816 v_border: 0
(II) RADEON(0): Unknown vendor-specific block f
(II) RADEON(0): SAMSUNG
(II) RADEON(0): 154AT01-001
(II) RADEON(0): EDID (in hex):
(II) RADEON(0): 00ffffffffffff004ca3453900000000
(II) RADEON(0): 00110103802115780a87f594574f8c27
(II) RADEON(0): 27505400000001010101010101010101
(II) RADEON(0): 010101010101ee1a0080502010301030
(II) RADEON(0): 13004bcf100000190000000f00000000
(II) RADEON(0): 00000000002387026400000000fe0053
(II) RADEON(0): 414d53554e470a2020202020000000fe
(II) RADEON(0): 00313534415430312d3030310a2000df
(II) RADEON(0): EDID vendor "SEC", prod id 14661
(II) RADEON(0): Output: HDMI-0, Detected Monitor Type: 0
(II) RADEON(0): Output: DVI-0, Detected Monitor Type: 0
Unhandled monitor type 0
Dac detection success
(II) RADEON(0): Output: VGA-0, Detected Monitor Type: 0
Output DIG0 transmitter setup success
Blank CRTC 0 success
Disable CRTC memreq 0 success
Disable CRTC 0 success
Mode 1280x800 - 1408 816 0
(II) RADEON(0): RADEONRestoreMemMapRegisters() :
(II) RADEON(0): MC_FB_LOCATION : 0x00df00d0 0x00df00d0
(II) RADEON(0): MC_AGP_LOCATION : 0x003f0000
before 6894
after 6894
ffreq: 68940.000000
best_freq: 68940
best_feedback_div: 86.8
best_ref_div: 2
best_post_div: 17
(II) RADEON(0): crtc(0) Clock: mode 68940, PLL 68940
(II) RADEON(0): crtc(0) PLL : refdiv 2, fbdiv 0x56(86), fracfbdiv 8, pdiv 17
Set CRTC 0 PLL success
Set CRTC Timing success
Set CRTC 0 Overscan success
Using RMX
scaler 0 setup success
Set CRTC 0 Source success
crtc 0 YUV disable setup success
Output DIG0 transmitter setup success
Output DIG2 encoder setup success
Output DIG2 encoder setup success
Output DIG0 transmitter setup success
Output DIG0 transmitter setup success
Output DIG0 transmitter setup success
Output DIG0 transmitter setup success
Enable CRTC 0 success
Enable CRTC memreq 0 success
Unblank CRTC 0 success
Output CRT1 disable success
Blank CRTC 1 success
Disable CRTC memreq 1 success
Disable CRTC 1 success
Output DIG0 transmitter setup success
Blank CRTC 0 success
Disable CRTC memreq 0 success
Disable CRTC 0 success
Mode 1280x800 - 1408 816 10
(II) RADEON(0): RADEONRestoreMemMapRegisters() :
(II) RADEON(0): MC_FB_LOCATION : 0x00df00d0 0x00df00d0
(II) RADEON(0): MC_AGP_LOCATION : 0x003f0000
before 6894
after 6894
ffreq: 68940.000000
best_freq: 68940
best_feedback_div: 86.8
best_ref_div: 2
best_post_div: 17
(II) RADEON(0): crtc(0) Clock: mode 68940, PLL 68940
(II) RADEON(0): crtc(0) PLL : refdiv 2, fbdiv 0x56(86), fracfbdiv 8, pdiv 17
Set CRTC 0 PLL success
Set CRTC Timing success
Set CRTC 0 Overscan success
Not using RMX
scaler 0 setup success
Set CRTC 0 Source success
crtc 0 YUV disable setup success
Output DIG0 transmitter setup success
Output DIG2 encoder setup success
Output DIG2 encoder setup success
Output DIG0 transmitter setup success
Output DIG0 transmitter setup success
Output DIG0 transmitter setup success
Output DIG0 transmitter setup success
Enable CRTC 0 success
Enable CRTC memreq 0 success
Unblank CRTC 0 success
Output CRT1 disable success
Blank CRTC 1 success
Disable CRTC memreq 1 success
Disable CRTC 1 successAnd here there is the output of dmesg:
http://pastebay.com/80523
Sorry it is too long for the forum I had to upload it somewhere....
Last edited by toroseduto (2010-01-05 14:13:02)
Offline
#558 2010-01-05 14:28:29
- Perry3D
- Member
- Registered: 2008-03-20
- Posts: 553
Re: Discussion: the ati/radeon open source drivers & radeon repository
From your dmesg:
r600_cp: Failed to load firmware "radeon/RV620_pfp.bin"
Make sure you installed kernel26-firmware-git and radeon_ucode from AUR.
Last edited by Perry3D (2010-01-05 14:28:42)
Offline
#559 2010-01-05 14:33:49
- Nezmer
- Member
- Registered: 2008-10-24
- Posts: 559
- Website
Re: Discussion: the ati/radeon open source drivers & radeon repository
toroseduto wrote:
And here there is the output of dmesg:
http://pastebay.com/80523
Sorry it is too long for the forum I had to upload it somewhere....
[drm] Loading RV620 Microcode
platform radeon_cp.0: firmware: requesting radeon/RV620_pfp.bin
firmware radeon_cp.0: firmware_loading_store: unexpected value (0)
r600_cp: Failed to load firmware "radeon/RV620_pfp.bin"
[drm:r600_startup] *ERROR* Failed to load firmware!You forgot kernel26-firmware?
English is not my native language .
Offline
#560 2010-01-06 08:36:34
- hunterthomson
- Member
- Registered: 2008-06-22
- Posts: 794
- Website
Re: Discussion: the ati/radeon open source drivers & radeon repository
I know this is not a good place to ask but I will anyway.....
Anyone know how well if at all the Open Driver is working on OpenBSD/NetBSD/FreeBSD or OpenSolaris?
Last edited by hunterthomson (2010-01-06 08:37:24)
OpenBSD-current Thinkpad X230, i7-3520M, 16GB CL9 Kingston, Samsung 830 256GB
Contributor: linux-grsec
Offline
#561 2010-01-06 08:44:17
- flamelab
- Member
- From: Athens, Hellas (Greece)
- Registered: 2007-12-26
- Posts: 2,160
Re: Discussion: the ati/radeon open source drivers & radeon repository
hunterthomson wrote:
I know this is not a good place to ask but I will anyway.....
Anyone know how well if at all the Open Driver is working on OpenBSD/NetBSD/FreeBSD or OpenSolaris?
I 'm sure that it works OK on FreeBSD 8.x, I'm not sure if you need -current ports.
Offline
#562 2010-01-06 08:57:28
- hunterthomson
- Member
- Registered: 2008-06-22
- Posts: 794
- Website
Re: Discussion: the ati/radeon open source drivers & radeon repository
Awe, ya it seems it is. I have a bad habit of posting too soon.
http://wiki.freebsd.org/DriDrivers
From 7.2-RELEASE, the radeondrm kernel module supports R600 and R700 cards but it only enables EXA and Xv acceleration at present. There is preliminary support for R6/700 3D in 8-STABLE and 9-CURRENT but this requires Mesa from git, not the version currently (20090831) in ports. The xf86-video-ati driver is the one being used by the developer with fairly good results.
It's ruff. I REALY want to use BSD but I am trying to study for the RHCE test. So, I have to stay on Linux otherwise I'll never learn enough to pass. I know for sure I could get the Linux+ in a month or two but it doesn't seem like anyone cares about the Linux+. The only things I need to learn are the RedHat only stuff like the tools they made, supported hardware and the RPM. I've never used RPM. Owe, I also like don't know much vi stuff because I like never use it when I am really coding. I wish there was a disto independent Linux Certification that was respected as much as RHCE. RedHat sucks anyway.... Hardened-Gentoo it the way to go for a secure Linux server IMHO.
Last edited by hunterthomson (2010-01-06 09:47:35)
OpenBSD-current Thinkpad X230, i7-3520M, 16GB CL9 Kingston, Samsung 830 256GB
Contributor: linux-grsec
Offline
#563 2010-01-06 19:35:53
- acmps
- Member
- Registered: 2009-09-01
- Posts: 44
Re: Discussion: the ati/radeon open source drivers & radeon repository
I have two problems.
1st. I can't get KMS working with 2.6.32.2 (yes I know you'll be all saying "but in this version it's broken", just read). I know this version doesn't support KMS but I don't even see any reference to drm or kms in dmesg! I'm using everything from git + radeon-initrd + radeon_ucode (just to be safe). Any help will be appreciated.
2nd. Can someone upload a package of kernel26-git or kernel26-rc (stock configs)? I can't compile it as my laptop overheats and shuts down when compiling the kernel (compiling other stuff works, it's just the kernel). Thanks.
Offline
#564 2010-01-06 20:12:56
- Rabauke
- Member
- From: Germany
- Registered: 2009-12-19
- Posts: 19
Re: Discussion: the ati/radeon open source drivers & radeon repository
acmps wrote:
I can't compile it as my laptop overheats and shuts down when compiling the kernel (compiling other stuff works, it's just the kernel). Thanks.
Yeah, I can confirm this. Had this issue last weekend. But you can continue compiling after restart.
Offline
#565 2010-01-06 22:23:49
- exiquio
- Member
- From: Santa Fe, NM, United States
- Registered: 2009-10-20
- Posts: 32
Re: Discussion: the ati/radeon open source drivers & radeon repository
EDIT:
I reinstalled the whole stack (from git) and now I have 3d with this kernel (2.6.33rc3) and kms:
OpenGL vendor string: Advanced Micro Devices, Inc.
OpenGL renderer string: Mesa DRI R600 (RS780 9612) 20090101 TCL DRI2
OpenGL version string: 2.0 Mesa 7.8-devel
OpenGL shading language version string: 1.10
OpenGL extensions:***
I am running kernel 2.6.33rc3. I compiled radeon as a module because it seems like kms no longer works when it is static. I have the kernel defaulting to kms. I have 3d acceleration when kms is off, but not when it is on.
Output from "glxinfo | grep opengl" (kms enabled):
OpenGL vendor string: Mesa Project
OpenGL renderer string: Software Rasterizer
OpenGL version string: 2.1 Mesa 7.8-devel
OpenGL shading language version string: 1.20
OpenGL extensions:Xorg.0.log (kms enabled):
This is a pre-release version of the X server from The X.Org Foundation.
It is not supported in any way.
Bugs may be filed in the bugzilla at http://bugs.freedesktop.org/.
Select the "xorg" product for bugs you find in this release.
Before reporting bugs in pre-release versions please check the
latest version in the X.Org Foundation git repository.
See http://wiki.x.org/wiki/GitPage for git access instructions.
X.Org X Server 1.7.3.902 (1.7.4 RC 2)
Release Date: 2009-12-26
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.33-rc2-CUSTOM x86_64
Current Operating System: Linux ghost_in_the_shell 2.6.33-rc3-CUSTOM #20 PREEMPT Wed Jan 6 14:35:50 MST 2010 x86_64
Kernel command line: cryptdevice=/dev/sda3:root root=/dev/mapper/root ro
Build Date: 27 December 2009 08:18:38PM
Current version of pixman: 0.16.4
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Wed Jan 6 14:48:17 2010
(II) Loader magic: 0x7b91c0
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 6.0
X.Org XInput driver : 7.0
X.Org Server Extension : 2.0
(--) using VT number 7
(--) PCI:*(0:1:5:0) 1002:9612:1025:028d ATI Technologies Inc RS780M/RS780MN [Radeon HD 3200 Graphics] rev 0, Mem @ 0xc0000000/268435456, 0xd2200000/65536, 0xd2100000/1048576, I/O @ 0x00007000/256
(==) Using default built-in configuration (30 lines)
(==) --- Start of built-in configuration ---
Section "Device"
Identifier "Builtin Default ati Device 0"
Driver "ati"
EndSection
Section "Screen"
Identifier "Builtin Default ati Screen 0"
Device "Builtin Default ati Device 0"
EndSection
Section "Device"
Identifier "Builtin Default vesa Device 0"
Driver "vesa"
EndSection
Section "Screen"
Identifier "Builtin Default vesa Screen 0"
Device "Builtin Default vesa Device 0"
EndSection
Section "Device"
Identifier "Builtin Default fbdev Device 0"
Driver "fbdev"
EndSection
Section "Screen"
Identifier "Builtin Default fbdev Screen 0"
Device "Builtin Default fbdev Device 0"
EndSection
Section "ServerLayout"
Identifier "Builtin Default Layout"
Screen "Builtin Default ati Screen 0"
Screen "Builtin Default vesa Screen 0"
Screen "Builtin Default fbdev Screen 0"
EndSection
(==) --- End of built-in configuration ---
(==) ServerLayout "Builtin Default Layout"
(**) |-->Screen "Builtin Default ati Screen 0" (0)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default ati Device 0"
(==) No monitor specified for screen "Builtin Default ati Screen 0".
Using a default monitor configuration.
(**) |-->Screen "Builtin Default vesa Screen 0" (1)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default vesa Device 0"
(==) No monitor specified for screen "Builtin Default vesa Screen 0".
Using a default monitor configuration.
(**) |-->Screen "Builtin Default fbdev Screen 0" (2)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default fbdev Device 0"
(==) No monitor specified for screen "Builtin Default fbdev Screen 0".
Using a default monitor configuration.
(==) Automatically adding devices
(==) Automatically enabling devices
(==) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/Type1
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) Cannot locate a core pointer device.
(II) Cannot locate a core keyboard device.
(II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
(II) Open ACPI successful (/var/run/acpid.socket)
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions/libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions/librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions/libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.1.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "ati"
(II) Loading /usr/lib/xorg/modules/drivers/ati_drv.so
(II) Module ati: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 6.12.99
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 6.0
(II) LoadModule: "radeon"
(II) Loading /usr/lib/xorg/modules/drivers/radeon_drv.so
(II) Module radeon: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 6.12.99
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 6.0
(II) LoadModule: "vesa"
(II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
(II) Module vesa: vendor="X.Org Foundation"
compiled for 1.7.0.901, module version = 2.2.1
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 6.0
(II) LoadModule: "fbdev"
(WW) Warning, couldn't open module fbdev
(II) UnloadModule: "fbdev"
(EE) Failed to load module "fbdev" (module does not exist, 0)
(II) RADEON: Driver for ATI Radeon chipsets:
ATI Radeon Mobility X600 (M24) 3150 (PCIE), ATI FireMV 2400 (PCI),
ATI Radeon Mobility X300 (M24) 3152 (PCIE),
ATI FireGL M24 GL 3154 (PCIE), ATI Radeon X600 (RV380) 3E50 (PCIE),
ATI FireGL V3200 (RV380) 3E54 (PCIE), ATI Radeon IGP320 (A3) 4136,
ATI Radeon IGP330/340/350 (A4) 4137, ATI Radeon 9500 AD (AGP),
ATI Radeon 9500 AE (AGP), ATI Radeon 9600TX AF (AGP),
ATI FireGL Z1 AG (AGP), ATI Radeon 9800SE AH (AGP),
ATI Radeon 9800 AI (AGP), ATI Radeon 9800 AJ (AGP),
ATI FireGL X2 AK (AGP), ATI Radeon 9600 AP (AGP),
ATI Radeon 9600SE AQ (AGP), ATI Radeon 9600XT AR (AGP),
ATI Radeon 9600 AS (AGP), ATI FireGL T2 AT (AGP), ATI Radeon 9650,
ATI FireGL RV360 AV (AGP), ATI Radeon 7000 IGP (A4+) 4237,
ATI Radeon 8500 AIW BB (AGP), ATI Radeon 8500 AIW BC (AGP),
ATI Radeon IGP320M (U1) 4336, ATI Radeon IGP330M/340M/350M (U2) 4337,
ATI Radeon Mobility 7000 IGP 4437, ATI Radeon 9000/PRO If (AGP/PCI),
ATI Radeon 9000 Ig (AGP/PCI), ATI Radeon X800 (R420) JH (AGP),
ATI Radeon X800PRO (R420) JI (AGP),
ATI Radeon X800SE (R420) JJ (AGP), ATI Radeon X800 (R420) JK (AGP),
ATI Radeon X800 (R420) JL (AGP), ATI FireGL X3 (R420) JM (AGP),
ATI Radeon Mobility 9800 (M18) JN (AGP),
ATI Radeon X800 SE (R420) (AGP), ATI Radeon X800XT (R420) JP (AGP),
ATI Radeon X800 VE (R420) JT (AGP), ATI Radeon X850 (R480) (AGP),
ATI Radeon X850 XT (R480) (AGP), ATI Radeon X850 SE (R480) (AGP),
ATI Radeon X850 PRO (R480) (AGP), ATI Radeon X850 XT PE (R480) (AGP),
ATI Radeon Mobility M7 LW (AGP),
ATI Mobility FireGL 7800 M7 LX (AGP),
ATI Radeon Mobility M6 LY (AGP), ATI Radeon Mobility M6 LZ (AGP),
ATI FireGL Mobility 9000 (M9) Ld (AGP),
ATI Radeon Mobility 9000 (M9) Lf (AGP),
ATI Radeon Mobility 9000 (M9) Lg (AGP), ATI Radeon 9700 Pro ND (AGP),
ATI Radeon 9700/9500Pro NE (AGP), ATI Radeon 9600TX NF (AGP),
ATI FireGL X1 NG (AGP), ATI Radeon 9800PRO NH (AGP),
ATI Radeon 9800 NI (AGP), ATI FireGL X2 NK (AGP),
ATI Radeon 9800XT NJ (AGP),
ATI Radeon Mobility 9600/9700 (M10/M11) NP (AGP),
ATI Radeon Mobility 9600 (M10) NQ (AGP),
ATI Radeon Mobility 9600 (M11) NR (AGP),
ATI Radeon Mobility 9600 (M10) NS (AGP),
ATI FireGL Mobility T2 (M10) NT (AGP),
ATI FireGL Mobility T2e (M11) NV (AGP), ATI Radeon QD (AGP),
ATI Radeon QE (AGP), ATI Radeon QF (AGP), ATI Radeon QG (AGP),
ATI FireGL 8700/8800 QH (AGP), ATI Radeon 8500 QL (AGP),
ATI Radeon 9100 QM (AGP), ATI Radeon 7500 QW (AGP/PCI),
ATI Radeon 7500 QX (AGP/PCI), ATI Radeon VE/7000 QY (AGP/PCI),
ATI Radeon VE/7000 QZ (AGP/PCI), ATI ES1000 515E (PCI),
ATI Radeon Mobility X300 (M22) 5460 (PCIE),
ATI Radeon Mobility X600 SE (M24C) 5462 (PCIE),
ATI FireGL M22 GL 5464 (PCIE), ATI Radeon X800 (R423) UH (PCIE),
ATI Radeon X800PRO (R423) UI (PCIE),
ATI Radeon X800LE (R423) UJ (PCIE),
ATI Radeon X800SE (R423) UK (PCIE),
ATI Radeon X800 XTP (R430) (PCIE), ATI Radeon X800 XL (R430) (PCIE),
ATI Radeon X800 SE (R430) (PCIE), ATI Radeon X800 (R430) (PCIE),
ATI FireGL V7100 (R423) (PCIE), ATI FireGL V5100 (R423) UQ (PCIE),
ATI FireGL unknown (R423) UR (PCIE),
ATI FireGL unknown (R423) UT (PCIE),
ATI Mobility FireGL V5000 (M26) (PCIE),
ATI Mobility FireGL V5000 (M26) (PCIE),
ATI Mobility Radeon X700 XL (M26) (PCIE),
ATI Mobility Radeon X700 (M26) (PCIE),
ATI Mobility Radeon X700 (M26) (PCIE),
ATI Radeon X550XTX 5657 (PCIE), ATI Radeon 9100 IGP (A5) 5834,
ATI Radeon Mobility 9100 IGP (U3) 5835,
ATI Radeon XPRESS 200 5954 (PCIE),
ATI Radeon XPRESS 200M 5955 (PCIE), ATI Radeon 9250 5960 (AGP),
ATI Radeon 9200 5961 (AGP), ATI Radeon 9200 5962 (AGP),
ATI Radeon 9200SE 5964 (AGP), ATI FireMV 2200 (PCI),
ATI ES1000 5969 (PCI), ATI Radeon XPRESS 200 5974 (PCIE),
ATI Radeon XPRESS 200M 5975 (PCIE),
ATI Radeon XPRESS 200 5A41 (PCIE),
ATI Radeon XPRESS 200M 5A42 (PCIE),
ATI Radeon XPRESS 200 5A61 (PCIE),
ATI Radeon XPRESS 200M 5A62 (PCIE),
ATI Radeon X300 (RV370) 5B60 (PCIE),
ATI Radeon X600 (RV370) 5B62 (PCIE),
ATI Radeon X550 (RV370) 5B63 (PCIE),
ATI FireGL V3100 (RV370) 5B64 (PCIE),
ATI FireMV 2200 PCIE (RV370) 5B65 (PCIE),
ATI Radeon Mobility 9200 (M9+) 5C61 (AGP),
ATI Radeon Mobility 9200 (M9+) 5C63 (AGP),
ATI Mobility Radeon X800 XT (M28) (PCIE),
ATI Mobility FireGL V5100 (M28) (PCIE),
ATI Mobility Radeon X800 (M28) (PCIE), ATI Radeon X850 5D4C (PCIE),
ATI Radeon X850 XT PE (R480) (PCIE),
ATI Radeon X850 SE (R480) (PCIE), ATI Radeon X850 PRO (R480) (PCIE),
ATI unknown Radeon / FireGL (R480) 5D50 (PCIE),
ATI Radeon X850 XT (R480) (PCIE),
ATI Radeon X800XT (R423) 5D57 (PCIE),
ATI FireGL V5000 (RV410) (PCIE), ATI Radeon X700 XT (RV410) (PCIE),
ATI Radeon X700 PRO (RV410) (PCIE),
ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X700 (RV410) (PCIE),
ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X1800,
ATI Mobility Radeon X1800 XT, ATI Mobility Radeon X1800,
ATI Mobility FireGL V7200, ATI FireGL V7200, ATI FireGL V5300,
ATI Mobility FireGL V7100, ATI Radeon X1800, ATI Radeon X1800,
ATI Radeon X1800, ATI Radeon X1800, ATI Radeon X1800,
ATI FireGL V7300, ATI FireGL V7350, ATI Radeon X1600, ATI RV505,
ATI Radeon X1300/X1550, ATI Radeon X1550, ATI M54-GL,
ATI Mobility Radeon X1400, ATI Radeon X1300/X1550,
ATI Radeon X1550 64-bit, ATI Mobility Radeon X1300,
ATI Mobility Radeon X1300, ATI Mobility Radeon X1300,
ATI Mobility Radeon X1300, ATI Radeon X1300, ATI Radeon X1300,
ATI RV505, ATI RV505, ATI FireGL V3300, ATI FireGL V3350,
ATI Radeon X1300, ATI Radeon X1550 64-bit, ATI Radeon X1300/X1550,
ATI Radeon X1600, ATI Radeon X1300/X1550, ATI Mobility Radeon X1450,
ATI Radeon X1300/X1550, ATI Mobility Radeon X2300,
ATI Mobility Radeon X2300, ATI Mobility Radeon X1350,
ATI Mobility Radeon X1350, ATI Mobility Radeon X1450,
ATI Radeon X1300, ATI Radeon X1550, ATI Mobility Radeon X1350,
ATI FireMV 2250, ATI Radeon X1550 64-bit, ATI Radeon X1600,
ATI Radeon X1650, ATI Radeon X1600, ATI Radeon X1600,
ATI Mobility FireGL V5200, ATI Mobility Radeon X1600,
ATI Radeon X1650, ATI Radeon X1650, ATI Radeon X1600,
ATI Radeon X1300 XT/X1600 Pro, ATI FireGL V3400,
ATI Mobility FireGL V5250, ATI Mobility Radeon X1700,
ATI Mobility Radeon X1700 XT, ATI FireGL V5200,
ATI Mobility Radeon X1700, ATI Radeon X2300HD,
ATI Mobility Radeon HD 2300, ATI Mobility Radeon HD 2300,
ATI Radeon X1950, ATI Radeon X1900, ATI Radeon X1950,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI AMD Stream Processor, ATI Radeon X1900, ATI Radeon X1950,
ATI RV560, ATI RV560, ATI Mobility Radeon X1900, ATI RV560,
ATI Radeon X1950 GT, ATI RV570, ATI RV570, ATI FireGL V7400,
ATI RV560, ATI Radeon X1650, ATI Radeon X1650, ATI RV560,
ATI Radeon 9100 PRO IGP 7834, ATI Radeon Mobility 9200 IGP 7835,
ATI Radeon X1200, ATI Radeon X1200, ATI Radeon X1200,
ATI Radeon X1200, ATI Radeon X1200, ATI RS740, ATI RS740M, ATI RS740,
ATI RS740M, ATI Radeon HD 2900 XT, ATI Radeon HD 2900 XT,
ATI Radeon HD 2900 XT, ATI Radeon HD 2900 Pro, ATI Radeon HD 2900 GT,
ATI FireGL V8650, ATI FireGL V8600, ATI FireGL V7600,
ATI Radeon 4800 Series, ATI Radeon HD 4870 x2,
ATI Radeon 4800 Series, ATI Radeon HD 4850 x2,
ATI FirePro V8750 (FireGL), ATI FirePro V7760 (FireGL),
ATI Mobility RADEON HD 4850, ATI Mobility RADEON HD 4850 X2,
ATI Radeon 4800 Series, ATI FirePro RV770, AMD FireStream 9270,
AMD FireStream 9250, ATI FirePro V8700 (FireGL),
ATI Mobility RADEON HD 4870, ATI Mobility RADEON M98,
ATI Radeon 4800 Series, ATI Radeon 4800 Series, ATI FirePro M7750,
ATI M98, ATI M98, ATI M98, ATI Mobility Radeon HD 4650,
ATI Radeon RV730 (AGP), ATI Mobility Radeon HD 4670,
ATI FirePro M5750, ATI Radeon RV730 (AGP),
ATI RV730XT [Radeon HD 4670], ATI RADEON E4600,
ATI Radeon HD 4600 Series, ATI RV730 PRO [Radeon HD 4650],
ATI FirePro V7750 (FireGL), ATI FirePro V5700 (FireGL),
ATI FirePro V3750 (FireGL), ATI Mobility Radeon HD 4830,
ATI Mobility Radeon HD 4850, ATI FirePro M7740, ATI RV740,
ATI Radeon HD 4770, ATI Radeon HD 4700 Series, ATI Radeon HD 4770,
ATI FirePro M5750, ATI RV610, ATI Radeon HD 2400 XT,
ATI Radeon HD 2400 Pro, ATI Radeon HD 2400 PRO AGP, ATI FireGL V4000,
ATI RV610, ATI Radeon HD 2350, ATI Mobility Radeon HD 2400 XT,
ATI Mobility Radeon HD 2400, ATI RADEON E2400, ATI RV610,
ATI FireMV 2260, ATI RV670, ATI Radeon HD3870,
ATI Mobility Radeon HD 3850, ATI Radeon HD3850,
ATI Mobility Radeon HD 3850 X2, ATI RV670,
ATI Mobility Radeon HD 3870, ATI Mobility Radeon HD 3870 X2,
ATI Radeon HD3870 X2, ATI FireGL V7700, ATI Radeon HD3850,
ATI Radeon HD3690, AMD Firestream 9170, ATI Radeon HD 4550,
ATI Radeon RV710, ATI Radeon RV710, ATI Radeon HD 4350,
ATI Mobility Radeon 4300 Series, ATI Mobility Radeon 4500 Series,
ATI Mobility Radeon 4500 Series, ATI FirePro RG220, ATI RV630,
ATI Mobility Radeon HD 2600, ATI Mobility Radeon HD 2600 XT,
ATI Radeon HD 2600 XT AGP, ATI Radeon HD 2600 Pro AGP,
ATI Radeon HD 2600 XT, ATI Radeon HD 2600 Pro, ATI Gemini RV630,
ATI Gemini Mobility Radeon HD 2600 XT, ATI FireGL V5600,
ATI FireGL V3600, ATI Radeon HD 2600 LE,
ATI Mobility FireGL Graphics Processor, ATI Radeon RV710,
ATI Radeon HD 3470, ATI Mobility Radeon HD 3430,
ATI Mobility Radeon HD 3400 Series, ATI Radeon HD 3450,
ATI Radeon HD 3450, ATI Radeon HD 3430, ATI Radeon HD 3450,
ATI FirePro V3700, ATI FireMV 2450, ATI FireMV 2260, ATI FireMV 2260,
ATI Radeon HD 3600 Series, ATI Radeon HD 3650 AGP,
ATI Radeon HD 3600 PRO, ATI Radeon HD 3600 XT,
ATI Radeon HD 3600 PRO, ATI Mobility Radeon HD 3650,
ATI Mobility Radeon HD 3670, ATI Mobility FireGL V5700,
ATI Mobility FireGL V5725, ATI Radeon HD 3200 Graphics,
ATI Radeon 3100 Graphics, ATI Radeon HD 3200 Graphics,
ATI Radeon 3100 Graphics, ATI Radeon HD 3300 Graphics,
ATI Radeon HD 3200 Graphics, ATI Radeon 3000 Graphics,
ATI Radeon HD 4200, ATI Radeon 4100, ATI Mobility Radeon HD 4200,
ATI Mobility Radeon 4100, ATI RS880
(II) VESA: driver for VESA chipsets: vesa
(II) Primary Device is: PCI 01@00:05:0
(II) [KMS] Kernel modesetting enabled.
(WW) Falling back to old probe method for vesa
(II) RADEON(0): Creating default Display subsection in Screen section
"Builtin Default ati Screen 0" for depth/fbbpp 24/32
(==) RADEON(0): Depth 24, (--) framebuffer bpp 32
(II) RADEON(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
(==) RADEON(0): Default visual is TrueColor
(==) RADEON(0): RGB weight 888
(II) RADEON(0): Using 8 bits per RGB (8 bit DAC)
(--) RADEON(0): Chipset: "ATI Radeon HD 3200 Graphics" (ChipID = 0x9612)
(II) RADEON(0): PCI card detected
(WW) RADEON(0): Color tiling is not yet supported on R600/R700
(II) RADEON(0): KMS Color Tiling: disabled
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 9, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 9, (OK)
drmOpenByBusid: Searching for BusID pci:0000:01:05.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 9, (OK)
drmOpenByBusid: drmOpenMinor returns 9
drmOpenByBusid: drmGetBusid reports pci:0000:01:05.0
(II) [drm] DRM interface version 1.3
(II) [drm] DRM open master succeeded.
(II) RADEON(0): Output LVDS has no monitor section
(II) RADEON(0): Output VGA-0 has no monitor section
(II) RADEON(0): EDID vendor "LGD", prod id 450
(II) RADEON(0): Printing DDC gathered Modelines:
(II) RADEON(0): Modeline "1366x768"x0.0 72.30 1366 1414 1446 1526 768 771 776 790 -hsync -vsync (47.4 kHz)
(II) RADEON(0): Output LVDS connected
(II) RADEON(0): Output VGA-0 disconnected
(II) RADEON(0): Using exact sizes for initial modes
(II) RADEON(0): Output LVDS using initial mode 1366x768
(II) RADEON(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
(II) RADEON(0): mem size init: gart size :1fdff000 vram size: s:10000000 visible:fba0000
(II) RADEON(0): EXA: Driver will allow EXA pixmaps in VRAM
(**) RADEON(0): Display dimensions: (340, 190) mm
(**) RADEON(0): DPI set to (102, 102)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules/libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(II) Loading sub module "exa"
(II) LoadModule: "exa"
(II) Loading /usr/lib/xorg/modules/libexa.so
(II) Module exa: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 2.5.0
ABI class: X.Org Video Driver, version 6.0
(II) UnloadModule: "vesa"
(II) Unloading /usr/lib/xorg/modules/drivers/vesa_drv.so
(--) Depth 24 pixmap format is 32 bpp
(II) RADEON(0): [DRI2] Setup complete
(II) RADEON(0): Front buffer size: 4608K
(II) RADEON(0): VRAM usage limit set to 227750K
(==) RADEON(0): Backing store disabled
(II) RADEON(0): Direct rendering enabled
(II) RADEON(0): Setting EXA maxPitchBytes
(II) EXA(0): Driver allocated offscreen pixmaps
(II) EXA(0): Driver registered support for the following operations:
(II) Solid
(II) Copy
(II) Composite (RENDER acceleration)
(II) UploadToScreen
(II) DownloadFromScreen
(II) RADEON(0): Acceleration enabled
(==) RADEON(0): DPMS enabled
(==) RADEON(0): Silken mouse enabled
(II) RADEON(0): Set up textured video
(II) RADEON(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(--) RandR disabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
record: RECORD extension enabled at configure time.
record: This extension is known to be broken, disabling extension now..
record: http://bugs.freedesktop.org/show_bug.cgi?id=20500
(EE) AIGLX error: Calling driver entry point failed
(EE) AIGLX: reverting to software rendering
(II) AIGLX: Screen 0 is not DRI capable
(II) AIGLX: Loaded and initialized /usr/lib/xorg/modules/dri/swrast_dri.so
(II) GLX: Initialized DRISWRAST GL provider for screen 0
(II) RADEON(0): Setting screen physical size to 361 x 203
(II) config/udev: Adding input device "Power Button" (/dev/input/event3)
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
compiled for 1.7.3, module version = 2.3.2
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 7.0
(**) "Power Button": always reports core events
(**) "Power Button": Device: "/dev/input/event3"
(II) "Power Button": Found keys
(II) "Power Button": Configuring as keyboard
(II) XINPUT: Adding extended input device ""Power Button"" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/udev: Adding input device "Lid Switch" (/dev/input/event2)
(**) "Lid Switch": always reports core events
(**) "Lid Switch": Device: "/dev/input/event2"
(WW) "Lid Switch": Don't know how to use device
(II) UnloadModule: "evdev"
(EE) PreInit returned NULL for ""Lid Switch""
(II) config/udev: Adding input device "Video Bus" (/dev/input/event4)
(**) "Video Bus": always reports core events
(**) "Video Bus": Device: "/dev/input/event4"
(II) "Video Bus": Found keys
(II) "Video Bus": Configuring as keyboard
(II) XINPUT: Adding extended input device ""Video Bus"" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/udev: Adding input device "Power Button" (/dev/input/event0)
(**) "Power Button": always reports core events
(**) "Power Button": Device: "/dev/input/event0"
(II) "Power Button": Found keys
(II) "Power Button": Configuring as keyboard
(II) XINPUT: Adding extended input device ""Power Button"" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/udev: Adding input device "Sleep Button" (/dev/input/event1)
(**) "Sleep Button": always reports core events
(**) "Sleep Button": Device: "/dev/input/event1"
(II) "Sleep Button": Found keys
(II) "Sleep Button": Configuring as keyboard
(II) XINPUT: Adding extended input device ""Sleep Button"" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/udev: Adding input device "AT Translated Set 2 keyboard" (/dev/input/event6)
(**) "AT Translated Set 2 keyboard": always reports core events
(**) "AT Translated Set 2 keyboard": Device: "/dev/input/event6"
(II) "AT Translated Set 2 keyboard": Found keys
(II) "AT Translated Set 2 keyboard": Configuring as keyboard
(II) XINPUT: Adding extended input device ""AT Translated Set 2 keyboard"" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/udev: Adding input device "SynPS/2 Synaptics TouchPad" (/dev/input/event7)
(II) LoadModule: "synaptics"
(II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
(II) Module synaptics: vendor="X.Org Foundation"
compiled for 1.7.3.901, module version = 1.2.1
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 7.0
(II) Synaptics touchpad driver version 1.2.1
(**) Option "Device" "/dev/input/event7"
(II) "SynPS/2 Synaptics TouchPad": x-axis range 1472 - 5472
(II) "SynPS/2 Synaptics TouchPad": y-axis range 1408 - 4448
(II) "SynPS/2 Synaptics TouchPad": pressure range 0 - 255
(II) "SynPS/2 Synaptics TouchPad": finger width range 0 - 0
(II) "SynPS/2 Synaptics TouchPad": buttons: left right
(--) "SynPS/2 Synaptics TouchPad": touchpad found
(**) "SynPS/2 Synaptics TouchPad": always reports core events
(II) XINPUT: Adding extended input device ""SynPS/2 Synaptics TouchPad"" (type: TOUCHPAD)
(**) "SynPS/2 Synaptics TouchPad": (accel) keeping acceleration scheme 1
(**) "SynPS/2 Synaptics TouchPad": (accel) acceleration profile 0
(--) "SynPS/2 Synaptics TouchPad": touchpad found
(II) config/udev: Adding input device "PC Speaker" (/dev/input/event5)
(**) "PC Speaker": always reports core events
(**) "PC Speaker": Device: "/dev/input/event5"
(WW) "PC Speaker": Don't know how to use device
(II) UnloadModule: "evdev"
(EE) PreInit returned NULL for ""PC Speaker""I do have everything installed as suggested in the first post including radeon_ucode. Any help would be great. Thanks.
Last edited by exiquio (2010-01-08 02:09:49)
"Unix is simple. It just takes a genius to understand its simplicity." – Dennis Ritchie
Offline
#566 2010-01-07 01:01:50
- hunterthomson
- Member
- Registered: 2008-06-22
- Posts: 794
- Website
Re: Discussion: the ati/radeon open source drivers & radeon repository
acmps wrote:
2nd. Can someone upload a package of kernel26-git or kernel26-rc (stock configs)? I can't compile it as my laptop overheats and shuts down when compiling the kernel (compiling other stuff works, it's just the kernel). Thanks.
Wow, that sucks. If I had it built I'd upload it.
You know one thing you "Could" do is edit the /etc/makepkg.conf
If you change this line
#MAKEFLAGS="-j2"
to
MAKEFLAGS="-j1"
That "Should" limit the # of parallel compilation threads to only 1
You can also specify this setting in the PKGBUILD file and that will be the setting that is used for that package only.
Gentoo Handbook
http://www.gentoo.org/doc/en/handbook/h … xml?full=1
MAKEOPTS
With MAKEOPTS you define how many parallel compilations should occur when you install a package.
A good choice is the number of CPUs in your system plus one, but this guideline isn't always perfect.
MAKEOPTS for a regular, 1-CPU system
MAKEOPTS="-j2"(Less clear Arch WiKi for Makepkg.conf)
MAKEFLAGS=
This is often used to set the number of jobs used, for example, -j2. Typically, this is modified for SMP systems.Last edited by hunterthomson (2010-01-07 02:26:18)
OpenBSD-current Thinkpad X230, i7-3520M, 16GB CL9 Kingston, Samsung 830 256GB
Contributor: linux-grsec
Offline
#567 2010-01-07 07:52:16
- kinski
- Member
- Registered: 2009-03-25
- Posts: 9
Re: Discussion: the ati/radeon open source drivers & radeon repository
Hi, all according to the 2.6.32.3 changelog kms should work again for r600 cards.
commit 08ff73341f9d5bde2d5e54bfe4d6a3d2a3f2ee83
Author: Dave Airlie <airlied@redhat.com>
Date: Mon Dec 21 14:33:52 2009 +1000drm/radeon/kms: fix crtc vblank update for r600
In 2.6.32.2 r600 had no IRQ support, however the patch in
500b758725314ab1b5316eb0caa5b0fa26740e6b to fix vblanks on avivo
cards, needs irqs.
So check for an R600 card and avoid this path if so.
This is a stable only patch for 2.6.32.2 as 2.6.33 has IRQs for r600.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Offline
#568 2010-01-07 09:43:55
- Ultraman
- Member
- Registered: 2009-12-24
- Posts: 242
Re: Discussion: the ati/radeon open source drivers & radeon repository
kinski wrote:
Hi, all according to the 2.6.32.3 changelog kms should work again for r600 cards.
commit 08ff73341f9d5bde2d5e54bfe4d6a3d2a3f2ee83
Author: Dave Airlie <airlied@redhat.com>
Date: Mon Dec 21 14:33:52 2009 +1000drm/radeon/kms: fix crtc vblank update for r600
In 2.6.32.2 r600 had no IRQ support, however the patch in
500b758725314ab1b5316eb0caa5b0fa26740e6b to fix vblanks on avivo
cards, needs irqs.
So check for an R600 card and avoid this path if so.
This is a stable only patch for 2.6.32.2 as 2.6.33 has IRQs for r600.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I believe that was already known. Phoronix reported on that a while back. Good to see confirmation tho 
Related (interesting) stuff I could find quickly:
http://www.phoronix.com/scan.php?page=n … &px=Nzc1MQ
http://www.phoronix.com/scan.php?page=n … &px=NzY5OA
http://www.phoronix.com/scan.php?page=n … &px=Nzc4OQ
http://www.phoronix.com/scan.php?page=n … &px=NzgzMA
Last edited by Ultraman (2010-01-07 09:56:13)
Offline
#569 2010-01-07 16:41:16
- acmps
- Member
- Registered: 2009-09-01
- Posts: 44
Re: Discussion: the ati/radeon open source drivers & radeon repository
hunterthomson wrote:
acmps wrote:2nd. Can someone upload a package of kernel26-git or kernel26-rc (stock configs)? I can't compile it as my laptop overheats and shuts down when compiling the kernel (compiling other stuff works, it's just the kernel). Thanks.
Wow, that sucks. If I had it built I'd upload it.
You know one thing you "Could" do is edit the /etc/makepkg.conf
If you change this line
#MAKEFLAGS="-j2"to
MAKEFLAGS="-j1"That "Should" limit the # of parallel compilation threads to only 1
You can also specify this setting in the PKGBUILD file and that will be the setting that is used for that package only.Gentoo Handbook
http://www.gentoo.org/doc/en/handbook/h … xml?full=1MAKEOPTS With MAKEOPTS you define how many parallel compilations should occur when you install a package. A good choice is the number of CPUs in your system plus one, but this guideline isn't always perfect. MAKEOPTS for a regular, 1-CPU system MAKEOPTS="-j2"(Less clear Arch WiKi for Makepkg.conf)
MAKEFLAGS= This is often used to set the number of jobs used, for example, -j2. Typically, this is modified for SMP systems.
I have -j3 in MAKEOPTS, I'll try and change it to j1. Thanks!
Offline
#570 2010-01-08 05:18:50
- hunterthomson
- Member
- Registered: 2008-06-22
- Posts: 794
- Website
Re: Discussion: the ati/radeon open source drivers & radeon repository
Alright
I tried to install the new Catalyst and everything got all messed up. After about 2hrs I said F-this and just removed the catalyst and the patched Xserver, commented out the Ignorepackge line in pacman.conf, moved my xorg.conf to xorg.conf-bkp, pacman -Syu, Reboot pacman -S xorg xf86-video-ati.....
Way nicer then I thought it would be. I am never going back to the Catalyst. I'm on the Open Source driver from now on.
-------------
ATI Mobility FireGL v5700 aka HD3650 ... R600
Core 2 Duo P8400 2.26 45nm
4GB DDR2 667 4-4-4-12
Native Resolution 1680-1050
2.6.32.2-2-x86_64-ARCH
xf86-video-ati #NO xorg.conf
All stock Stable Repo packages
Kwin Effects ON # All WAY Better then with the Catalyst.
Flash Video EVEN Hulu! I can watch Full-Screen NOW YA! I could NEVER do that with the Catalyst.. well I think I could a long time ago but it keeps getting worse and worse with every new Catalyst release.
Quakelive at default settings Fullscreen at native resolution - 50FPS < 150FPS # Vary Vary Playable
- Kwin Effects OFF -
Nexuiz-GLX "Normal" settings Native Resolution - 25FPS < 45FPS # Vary Playable
OpenArena normal-low settings Native Resolution - ?FPS can't find how to run that on # Vary Vary Playable
AlainArena Lowest everything - 10FPS # Not Playable
----------------------
Xorg Error and Warnings
It just has some stuff about fbdev. However, latter in the log it dose load the radeon fbdev.
It also says HAL loads the dri, xvid and the other stuff
cat /var/log/Xorg.0.log | grep EE
Current Operating System: Linux LinuxBox 2.6.32-ARCH #1 SMP PREEMPT Sat Dec 26 09:02:58 CET 2009 x86_64
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(II) Loading extension MIT-SCREEN-SAVER
(EE) Failed to load module "fbdev" (module does not exist, 0)
cat /var/log/Xorg.0.log | grep WW
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(WW) Warning, couldn't open module fbdev
(WW) Falling back to old probe method for vesa
(WW) RADEON(0): LVDS Info:
(WW) RADEON(0): DRI init changed memory map, adjusting ...
(WW) RADEON(0): MC_FB_LOCATION was: 0x00cf00c0 is: 0x00cf00c0
(WW) RADEON(0): MC_AGP_LOCATION was: 0x003f0000 is: 0x00030000Last edited by hunterthomson (2010-01-08 11:36:39)
OpenBSD-current Thinkpad X230, i7-3520M, 16GB CL9 Kingston, Samsung 830 256GB
Contributor: linux-grsec
Offline
#571 2010-01-08 23:42:37
- badenov
- Member
- Registered: 2009-12-13
- Posts: 5
Re: Discussion: the ati/radeon open source drivers & radeon repository
After yesterday's nightly repo updates:
(EE) AIGLX error: dlopen of /usr/lib/xorg/modules/dri/r600_dri.so failed (/usr/lib/xorg/modules/dri/r600_dri.so: undefined symbol: _mesa_framebuffer_renderbuffer)
(EE) AIGLX: reverting to software rendering
(EE) AIGLX error: dlopen of /usr/lib/xorg/modules/dri/swrast_dri.so failed (/usr/lib/xorg/modules/dri/swrast_dri.so: undefined symbol: _mesa_framebuffer_renderbuffer)
(EE) GLX: could not load software renderer[badenov@./dri 1886]:) % pacman -Qo ./r600_dri.so
./r600_dri.so is owned by ati-dri-git 20100108-1Glxinfo, KMS, 3d don't work. I tried with kernel 2.6.32.2 and 2.6.33-rc2, ati-dri-git from nightly repo and compiled from git.
Offline
#572 2010-01-09 11:17:12
- slon
- Member
- Registered: 2009-12-28
- Posts: 29
Re: Discussion: the ati/radeon open source drivers & radeon repository
Everything taken from AUR so running 2.6.33rc3 kernel successfully with KMS ati 3650
Tremulous, Urban terror running fine
Alien arena very laggy so unplayable
Savage2 - Fatal Error: GLSL 1.20 not available.
Offline
#573 2010-01-09 11:24:46
- registeringsucks
- Member
- Registered: 2009-04-27
- Posts: 27
Re: Discussion: the ati/radeon open source drivers & radeon repository
I have a strange problem with compositing and kde4. If i boot normally, kde isnt able to turn compositing on.
After i do a "killall kdm" everything works nicely. How is that possible?
I have a Ati 4850 and use xf86-video-ati-git, everything else is from testing/extra.
Offline
#574 2010-01-09 13:37:14
- insanemal
- Member
- From: Brisbane/Australia
- Registered: 2009-05-05
- Posts: 140
Re: Discussion: the ati/radeon open source drivers & radeon repository
Well.. I've been mucking around with GIT Mesa builds...
7.7.1-Devel seems to be awesome.
It's only Ogl 1.4 and no GLSL, however QuakeLive is back to 60-100FPS from only 3fps.
I'm compiling Mesa-full from AUR with "git checkout mesa_7_7_branch" added in. Oh and you have to remove the lines to add Nouveau support as it doesn't compile at the moment.
I'm going to test out 7.8 again soon, as the last time I compiled it was back in December.. and there seems to have been quite a bit of work on the r600 support since then.
EDIT:
7.8 is still 4fps.
Last edited by insanemal (2010-01-09 14:08:14)
Offline
#575 2010-01-09 21:51:17
- slon
- Member
- Registered: 2009-12-28
- Posts: 29
Re: Discussion: the ati/radeon open source drivers & radeon repository
Yes I agree Mesa 7.8dev pretty much is useless for gaming But on 7.7 cant get KMS.....
Offline