Me and my internet.

BlackFenix · 2005-01-28 22:00:38

Before post my problem i'm try another distro (ubuntu) and my net work's fine.

Back to arch (for me, it's better) i make some modifications in /etc/hotplug/blacklist adding shcphp because hotplug fail to load this.
I have a D-Link DSL500G (admin ip 10.1.1.1) and configure my eth0 to 10.1.1.5 mask 255.255.255.0 and broadcast 10.1.1.255
My module is sis900 and are loaded.
But i can't connect. Ping 10.1.1.1 and works fine. Ping -c 3 ftp.archlinux.org after some seconds fail.

Where is the error ?

phrakture · 2005-01-28 22:09:56

ok, I am assuming the D-Link is a router... if you can ping the router, but can't get through it... and you're on a static IP... do you have your route setup... you need a default for static IP...

BlackFenix · 2005-01-28 22:17:11

phrakture wrote:

ok, I am assuming the D-Link is a router...

Yes, my modem is a router

phrakture wrote:

if you can ping the router, but can't get through it... and you're on a static IP... do you have your route setup... you need a default for static IP...

yes again, i can ping the router and i defined a static ip because network don't start if is configured to dhcp.
But how ubuntu can connect with the same config ? Sorry, i don't understand what you say with "do you have your route setup... you need a default for static IP."

A friend will translate for me... :oops:

phrakture · 2005-01-28 22:27:09

in rc.conf:

gateway="default gw 192.168.1.1"
ROUTES=(gateway)

or in a console:

# route add default gw 192.168.1.1 netmask 0.0.0.0 dev eth0

no this needs to be adapted to your setup, so I think you want 10.1.1.1 as your gateway

BlackFenix · 2005-01-28 22:40:45

i forgot to mention: my gateway already configured to 10.1.1.1

Benedict_White · 2005-01-28 23:48:36

the 10.0.0.0 private network is as a default defined as a class A network, with a mask of 255.0.0.0

(That said it can of course be configured any way you want.)

Try a class A mask rather than a class C one and let us know what happens.

BlackFenix · 2005-01-31 11:17:32

Sorry for post my problem ( http://bbs.archlinux.org/viewtopic.php?t=9541
) in a wrong place Embarassed
Benedict_White wrote:
the 10.0.0.0 private network is as a default defined as a class A network, with a mask of 255.0.0.0
(That said it can of course be configured any way you want.)
Try a class A mask rather than a class C one and let us know what happens.

Nothing happens
I'm try slackware and it's also work but i want use arch.
In salckware, i'm fill IP, Mask, Gateway and "DNS". How i can change DNS information in arch ? rc.conf ? How ?

BlackFenix · 2005-01-31 12:34:27

From me to me

http://bbs.archlinux.org/viewtopic.php? … ns+rc+conf

BlackFenix · 2005-02-01 11:13:35

I give up :cry:
My rc.conf, resolv.conf is fine my module is loaded but arch don't connect.

IceRAM · 2005-02-01 11:48:58

Are you sure you did everything here:
http://wiki2.archlinux.org/index.php/St … and%20DHCP
?

Try running hwd - search forums = it will detect the necessary modules [it did for me, as I didn't know I had to manually load (I don't use hotplug) "uhci_hcd"]

BlackFenix · 2005-02-01 14:39:27

Hummm...
I will check the hosts file....

Arch Linux

#1 2005-01-28 22:00:38

Me and my internet.

#2 2005-01-28 22:09:56

Re: Me and my internet.

#3 2005-01-28 22:17:11

Re: Me and my internet.

#4 2005-01-28 22:27:09

Re: Me and my internet.

#5 2005-01-28 22:40:45

Re: Me and my internet.

#6 2005-01-28 23:48:36

Re: Me and my internet.

#7 2005-01-31 11:17:32

Re: Me and my internet.

#8 2005-01-31 12:34:27

Re: Me and my internet.

#9 2005-02-01 11:13:35

Re: Me and my internet.

#10 2005-02-01 11:48:58

Re: Me and my internet.

#11 2005-02-01 14:39:27

Re: Me and my internet.

Board footer