You are not logged in.

#1 2012-07-02 16:05:07

mcapu
Member
Registered: 2012-07-02
Posts: 6

GDM and Gnome not working, showing only the cursor and wallpaper

Hi all, I've just started with ArchLinux. After a clean install GDM and Gnome don't work. I'll explain my error:

- gdm freezes just when I start it and show only the mouse cursor. I can move it.

- gnome shows only the wallpaper and again I can move the cursor, but nothing happens.
I've tried starting it whit startx, with kdm and with slim. None of them works. The .xinitrc I have been using consists in a single line:

#!/bin/sh
exec gnome-session
#exec ck-launch-session gnome-session
#exec ck-launch-session dbus-launch gnome-session

I have tried the three commands. I have tried loading slim and kdm from inittab and from rc.conf, as well as directly typing the command in the tty.

Openbox and KDE work just fine. I have tried to find something in the .xsession-errors, but it doesn't exist. The best I can get is the slim.log in /var/log/ and the gdm logs in /var/log/gdm/
I have tried switching the graphic drivers from nvidia to nouveau. I have even reinstalled Arch from scratch but it did nothing to stop this error.

Dbus is running from rc.conf and showing in the ps as running, but the gdm logs show that somehow they aren't communicating (or at least I think so).
In the logs I can see an error saying that .Xauthority does not exist, but the strangest thing is that it DOES exist.

I have been three days struggling with this, searching in these forums but I can't solve it. Any help will be much appreciated, thanks.

PS: There they are the logs from /var/log:

/var/log/gdm/:0-slave.log

gdm-welcome][588]: AccountsService-WARNING: Failed to connect to the D-Bus daemon: No se pudo conectar: No existe el fichero o el directorio
gdm-welcome][588]: GLib-GIO-CRITICAL: g_dbus_proxy_call_internal: assertion `G_IS_DBUS_PROXY (proxy)' failed
**
AccountsService:ERROR:act-user-manager.c:2115:load_users: assertion failed: (manager->priv->accounts_proxy != NULL)
gdm[589]: ******************* START **********************************
gdm[589]: [Thread debugging using libthread_db enabled]
gdm[589]: Using host libthread_db library "/lib/libthread_db.so.1".
gdm[589]: 0x00007f6b09090cca in waitpid () from /lib/libpthread.so.0
Traceback (most recent call last):
  File "/usr/share/gdb/auto-load/usr/lib/libgobject-2.0.so.0.3200.3-gdb.py", line 9, in <module>
    from gobject import register
  File "/usr/share/glib-2.0/gdb/gobject.py", line 3, in <module>
    import gdb.backtrace
ImportError: No module named backtrace
gdm[589]: #0  0x00007f6b09090cca in waitpid () from /lib/libpthread.so.0
gdm[589]: #1  0x000000000040e020 in ?? ()
gdm[589]: #2  0x000000000040e35a in ?? ()
gdm[589]: #3  <signal handler called>
gdm[589]: #4  0x00007f6b08592c35 in raise () from /lib/libc.so.6
gdm[589]: #5  0x00007f6b085940b8 in abort () from /lib/libc.so.6
gdm[589]: #6  0x00007f6b08ba8627 in g_assertion_message () from /usr/lib/libglib-2.0.so.0
gdm[589]: #7  0x00007f6b08ba8b44 in g_assertion_message_expr () from /usr/lib/libglib-2.0.so.0
gdm[589]: #8  0x00007f6b08918206 in ?? () from /usr/lib/libaccountsservice.so.0
gdm[589]: #9  0x00007f6b08b874a5 in g_main_context_dispatch () from /usr/lib/libglib-2.0.so.0
gdm[589]: #10 0x00007f6b08b877d8 in ?? () from /usr/lib/libglib-2.0.so.0
gdm[589]: #11 0x00007f6b08b87bd2 in g_main_loop_run () from /usr/lib/libglib-2.0.so.0
gdm[589]: #12 0x000000000040533e in ?? ()
gdm[589]: #13 0x00007f6b0857f455 in __libc_start_main () from /lib/libc.so.6
gdm[589]: #14 0x00000000004053e1 in ?? ()
gdm[589]: #15 0x00007fff6ce1f2c8 in ?? ()
gdm[589]: #16 0x0000000000000000 in ?? ()
gdm[589]: 
gdm[589]: Thread 1 (Thread 0x7f6b06b27700 (LWP 588)):
gdm[589]: #0  0x00007f6b09090cca in waitpid () from /lib/libpthread.so.0
gdm[589]: No symbol table info available.
gdm[589]: #1  0x000000000040e020 in ?? ()
gdm[589]: No symbol table info available.
gdm[589]: #2  0x000000000040e35a in ?? ()
gdm[589]: No symbol table info available.
gdm[589]: #3  <signal handler called>
gdm[589]: No symbol table info available.
gdm[589]: #4  0x00007f6b08592c35 in raise () from /lib/libc.so.6
gdm[589]: No symbol table info available.
gdm[589]: #5  0x00007f6b085940b8 in abort () from /lib/libc.so.6
gdm[589]: No symbol table info available.
gdm[589]: #6  0x00007f6b08ba8627 in g_assertion_message () from /usr/lib/libglib-2.0.so.0
gdm[589]: No symbol table info available.
gdm[589]: #7  0x00007f6b08ba8b44 in g_assertion_message_expr () from /usr/lib/libglib-2.0.so.0
gdm[589]: No symbol table info available.
gdm[589]: #8  0x00007f6b08918206 in ?? () from /usr/lib/libaccountsservice.so.0
gdm[589]: No symbol table info available.
gdm[589]: #9  0x00007f6b08b874a5 in g_main_context_dispatch () from /usr/lib/libglib-2.0.so.0
gdm[589]: No symbol table info available.
gdm[589]: #10 0x00007f6b08b877d8 in ?? () from /usr/lib/libglib-2.0.so.0
gdm[589]: No symbol table info available.
gdm[589]: #11 0x00007f6b08b87bd2 in g_main_loop_run () from /usr/lib/libglib-2.0.so.0
gdm[589]: No symbol table info available.
gdm[589]: #12 0x000000000040533e in ?? ()
gdm[589]: No symbol table info available.
gdm[589]: #13 0x00007f6b0857f455 in __libc_start_main () from /lib/libc.so.6
gdm[589]: No symbol table info available.
gdm[589]: #14 0x00000000004053e1 in ?? ()
gdm[589]: No symbol table info available.
gdm[589]: #15 0x00007fff6ce1f2c8 in ?? ()
gdm[589]: No symbol table info available.
gdm[589]: #16 0x0000000000000000 in ?? ()
gdm[589]: No symbol table info available.
gdm[589]: A debugging session is active.
gdm[589]: 
gdm[589]:     Inferior 1 [process 588] will be detached.
gdm[589]: 
gdm[589]: Quit anyway? (y or n) [answered Y; input not from terminal]
gdm[589]: ******************* END **********************************
gdm-simple-slave[566]: WARNING: Freeing conversation 'gdm-welcome' with active job

/var/log/slim.log

X.Org X Server 1.12.2
Release Date: 2012-05-29
X Protocol Version 11, Revision 0
Build Operating System: Linux 3.0.32-1-lts x86_64 
Current Operating System: Linux mcapu 3.4.4-2-ARCH #1 SMP PREEMPT Sun Jun 24 18:59:47 CEST 2012 x86_64
Kernel command line: root=/dev/sda4 ro
Build Date: 30 May 2012  07:24:13PM
 
Current version of pixman: 0.26.2
    Before reporting problems, check [url]http://wiki.x.org[/url]
    to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Mon Jul  2 03:08:15 2012
(==) Using config file: "/etc/X11/xorg.conf"
(==) Using config directory: "/etc/X11/xorg.conf.d"

slim: waiting for X server to begin accepting connections.
/usr/bin/xauth:  file /home/prueba/.Xauthority does not exist
GNOME_KEYRING_CONTROL=/home/prueba/.cache/keyring-4r9utW
SSH_AUTH_SOCK=/home/prueba/.cache/keyring-4r9utW/ssh
GNOME_KEYRING_CONTROL=/home/prueba/.cache/keyring-4r9utW
SSH_AUTH_SOCK=/home/prueba/.cache/keyring-4r9utW/ssh
GNOME_KEYRING_CONTROL=/home/prueba/.cache/keyring-4r9utW
SSH_AUTH_SOCK=/home/prueba/.cache/keyring-4r9utW/ssh
GPG_AGENT_INFO=/home/prueba/.cache/keyring-4r9utW/gpg:0:1
GNOME_KEYRING_CONTROL=/home/prueba/.cache/keyring-4r9utW
SSH_AUTH_SOCK=/home/prueba/.cache/keyring-4r9utW/ssh
GPG_AGENT_INFO=/home/prueba/.cache/keyring-4r9utW/gpg:0:1

(gnome-settings-daemon:639): libupower-glib-WARNING **: Couldn't enumerate devices: Message did not receive a reply (timeout by message bus)

(gnome-settings-daemon:639): power-plugin-WARNING **: failed to get device list: Message did not receive a reply (timeout by message bus)

(gnome-settings-daemon:639): print-notifications-plugin-WARNING **: Unable to start print-notifications manager: No se pudo conectar: No existe el fichero o el directorio

** (gnome-settings-daemon:639): WARNING **: cannot connect to ConsoleKit: No se pudo conectar: No existe el fichero o el directorio

(gnome-settings-daemon:639): power-plugin-WARNING **: Could not connect to UPower: No se pudo conectar: No existe el fichero o el directorio

(gnome-settings-daemon:639): power-plugin-WARNING **: Could not connect to UPower: No se pudo conectar: No existe el fichero o el directorio

** (gnome-settings-daemon:639): WARNING **: cannot connect to ConsoleKit: No se pudo conectar: No existe el fichero o el directorio

(gnome-settings-daemon:639): color-plugin-WARNING **: failed to connect to colord: No se pudo conectar: No existe el fichero o el directorio

(gnome-settings-daemon:639): media-keys-plugin-WARNING **: Failed to get proxy for upower: No se pudo conectar: No existe el fichero o el directorio
Initializing tracker-miner-fs...
Tracker-Message: Setting up monitor for changes to config file:'/home/prueba/.config/tracker/tracker-miner-fs.cfg'
Starting log:
  File:'/home/prueba/.local/share/tracker/tracker-miner-fs.log'
Failed to play sound: File or data not found
Initializing tracker-store...
Tracker-Message: Setting up monitor for changes to config file:'/home/prueba/.config/tracker/tracker-store.cfg'
Tracker-Message: Setting up monitor for changes to config file:'/home/prueba/.config/tracker/tracker-store.cfg'
Starting log:
  File:'/home/prueba/.local/share/tracker/tracker-store.log'
The XKEYBOARD keymap compiler (xkbcomp) reports:
> Warning:          Compat map for group 2 redefined
>                   Using new definition
> Warning:          Compat map for group 3 redefined
>                   Using new definition
> Warning:          Compat map for group 4 redefined
>                   Using new definition
Errors from xkbcomp are not fatal to the X server

** (nm-applet:689): WARNING **: Could not initialize NMClient /org/freedesktop/NetworkManager: Launch helper exited with unknown return code 1
** Message: applet now removed from the notification area

** (nm-applet:689): WARNING **: fetch_connections_done: error fetching connections: (25) Launch helper exited with unknown return code 1.

(tracker-store:697): Tracker-CRITICAL **: D-Bus service name:'org.freedesktop.Tracker1' is already taken, perhaps the daemon is already running?

** (nm-applet:689): WARNING **: Failed to register as an agent: (25) Launch helper exited with unknown return code 1

(tracker-miner-fs:688): GVFS-RemoteVolumeMonitor-WARNING **: remote volume monitor with dbus name org.gtk.Private.UDisks2VolumeMonitor is not supported

(gnome-shell:682): GVFS-RemoteVolumeMonitor-WARNING **: remote volume monitor with dbus name org.gtk.Private.UDisks2VolumeMonitor is not supported
    JS ERROR: !!!   Exception was: Error: Error invoking Gio.bus_get_sync: No se pudo conectar: No existe el fichero o el directorio
    JS ERROR: !!!     lineNumber = '0'
    JS ERROR: !!!     fileName = '"gjs_throw"'
    JS ERROR: !!!     stack = '"("Error invoking Gio.bus_get_sync: No se pudo conectar: No existe el fichero o el directorio")@gjs_throw:0
()@/usr/share/gjs-1.0/overrides/Gio.js:341
ConsoleKitManager()@/usr/share/gnome-shell/js/ui/automountManager.js:40
()@/usr/share/gnome-shell/js/ui/automountManager.js:84
wrapper()@/usr/share/gjs-1.0/lang.js:204
()@/usr/share/gjs-1.0/lang.js:145
()@/usr/share/gjs-1.0/lang.js:239
_createUserSession()@/usr/share/gnome-shell/js/ui/main.js:86
start()@/usr/share/gnome-shell/js/ui/main.js:226
@<main>:1
"'
    JS ERROR: !!!     message = '"Error invoking Gio.bus_get_sync: No se pudo conectar: No existe el fichero o el directorio"'
Advertencia del gestor de ventanas: Log level 32: Execution of main.js threw exception: Error: Error invoking Gio.bus_get_sync: No se pudo conectar: No existe el fichero o el directorio
** Message: Starting applet secret agent because GNOME Shell disappeared

Last edited by mcapu (2012-07-02 16:13:59)

Offline

#2 2012-07-02 16:10:38

Inxsible
Forum Fellow
From: Chicago
Registered: 2008-06-09
Posts: 9,183

Re: GDM and Gnome not working, showing only the cursor and wallpaper

welcome to the forums mcapu. Please edit your posts and use [ code ] tags as opposed to [ quote ] tags. [ code ] tags provide scrollers which avoids the thread from getting too long.


Forum Rules

There's no such thing as a stupid question, but there sure are a lot of inquisitive idiots !

Offline

#3 2012-07-03 15:22:20

mcapu
Member
Registered: 2012-07-02
Posts: 6

Re: GDM and Gnome not working, showing only the cursor and wallpaper

Well, I read somewhere that this could be happening due to having created the user before installing gnome, but I made another user for testing and the same problem occurs.

Offline

#4 2012-07-03 15:24:00

nomorewindows
Member
Registered: 2010-04-03
Posts: 3,362

Re: GDM and Gnome not working, showing only the cursor and wallpaper

The line in .xinitrc needs to be exec ck-launch-session gnome-session


I may have to CONSOLE you about your usage of ridiculously easy graphical interfaces...
Look ma, no mouse.

Offline

#5 2012-07-03 15:46:44

mcapu
Member
Registered: 2012-07-02
Posts: 6

Re: GDM and Gnome not working, showing only the cursor and wallpaper

nomorewindows wrote:

The line in .xinitrc needs to be exec ck-launch-session gnome-session

Yes, I tried that one too. I tried the three lines posted there.

Offline

#6 2012-07-04 19:04:19

mcapu
Member
Registered: 2012-07-02
Posts: 6

Re: GDM and Gnome not working, showing only the cursor and wallpaper

Any advice?

Offline

#7 2012-07-04 23:05:20

nomorewindows
Member
Registered: 2010-04-03
Posts: 3,362

Re: GDM and Gnome not working, showing only the cursor and wallpaper

How about your /var/log/Xorg.0.log or dmesg?


I may have to CONSOLE you about your usage of ridiculously easy graphical interfaces...
Look ma, no mouse.

Offline

#8 2012-07-05 02:18:15

liveag
Member
Registered: 2011-08-20
Posts: 3

Re: GDM and Gnome not working, showing only the cursor and wallpaper

I'm having the same problem too.
My X writes this:

X.Org X Server 1.12.2
Release Date: 2012-05-29
X Protocol Version 11, Revision 0
Build Operating System: Linux 3.0.32-1-lts x86_64 
Current Operating System: Linux guru 3.4.4-2-ARCH #1 SMP PREEMPT Sun Jun 24 18:59:47 CEST 2012 x86_64
Kernel command line: root=/dev/sdb1 ro vga=795
Build Date: 30 May 2012  07:24:13PM
 
Current version of pixman: 0.26.2
	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.1.log", Time: Thu Jul  5 06:14:45 2012
(==) Using config directory: "/etc/X11/xorg.conf.d"

(process:2265): Gtk-WARNING **: Locale not supported by C library.
	Using the fallback 'C' locale.

(process:2272): Gtk-WARNING **: Locale not supported by C library.
	Using the fallback 'C' locale.
GNOME_KEYRING_CONTROL=/home/gabriel/.cache/keyring-zOty4S
GPG_AGENT_INFO=/home/gabriel/.cache/keyring-zOty4S/gpg:0:1
GNOME_KEYRING_PID=2281

(process:2276): Gtk-WARNING **: Locale not supported by C library.
	Using the fallback 'C' locale.
GNOME_KEYRING_CONTROL=/home/gabriel/.cache/keyring-zOty4S
GPG_AGENT_INFO=/home/gabriel/.cache/keyring-zOty4S/gpg:0:1
SSH_AUTH_SOCK=/home/gabriel/.cache/keyring-zOty4S/ssh
GNOME_KEYRING_CONTROL=/home/gabriel/.cache/keyring-zOty4S
GPG_AGENT_INFO=/home/gabriel/.cache/keyring-zOty4S/gpg:0:1
SSH_AUTH_SOCK=/home/gabriel/.cache/keyring-zOty4S/ssh
GNOME_KEYRING_CONTROL=/home/gabriel/.cache/keyring-zOty4S
GPG_AGENT_INFO=/home/gabriel/.cache/keyring-zOty4S/gpg:0:1
SSH_AUTH_SOCK=/home/gabriel/.cache/keyring-zOty4S/ssh

(gnome-settings-daemon:2276): libupower-glib-WARNING **: Couldn't enumerate devices: Message did not receive a reply (timeout by message bus)

(gnome-settings-daemon:2276): power-plugin-WARNING **: failed to get device list: Message did not receive a reply (timeout by message bus)

(gnome-settings-daemon:2276): print-notifications-plugin-WARNING **: Unable to start print-notifications manager: Could not connect: No such file or directory

** (gnome-settings-daemon:2276): WARNING **: cannot connect to ConsoleKit: Could not connect: No such file or directory

(gnome-settings-daemon:2276): power-plugin-WARNING **: Could not connect to UPower: Could not connect: No such file or directory

(gnome-settings-daemon:2276): power-plugin-WARNING **: Could not connect to UPower: Could not connect: No such file or directory

** (gnome-settings-daemon:2276): WARNING **: cannot connect to ConsoleKit: Could not connect: No such file or directory

(gnome-settings-daemon:2276): color-plugin-WARNING **: failed to connect to colord: Could not connect: No such file or directory

(gnome-settings-daemon:2276): media-keys-plugin-WARNING **: Failed to get proxy for upower: Could not connect: No such file or directory
Window manager warning: Locale not understood by C library, internationalization will not work

(gnome-shell:2355): Clutter-WARNING **: Locale not supported by C library.
Using the fallback 'C' locale.

(gnome-shell:2355): Gtk-WARNING **: Locale not supported by C library.
	Using the fallback 'C' locale.
[1341461713,000,xklavier.c:xkl_engine_start_listen/] 	The backend does not require manual layout management - but it is provided by the application

(process:2362): Gtk-WARNING **: Locale not supported by C library.
	Using the fallback 'C' locale.

(process:2363): Gtk-WARNING **: Locale not supported by C library.
	Using the fallback 'C' locale.

(process:2365): Gtk-WARNING **: Locale not supported by C library.
	Using the fallback 'C' locale.

(process:2366): Gtk-WARNING **: Locale not supported by C library.
	Using the fallback 'C' locale.
The XKEYBOARD keymap compiler (xkbcomp) reports:
> Warning:          Compat map for group 2 redefined
>                   Using new definition
> Warning:          Compat map for group 3 redefined
>                   Using new definition
> Warning:          Compat map for group 4 redefined
>                   Using new definition
Errors from xkbcomp are not fatal to the X server
Failed to play sound: File or data not found

** (nm-applet:2363): WARNING **: Could not initialize NMClient /org/freedesktop/NetworkManager: Launch helper exited with unknown return code 1
** Message: applet now removed from the notification area

** (nm-applet:2363): WARNING **: fetch_connections_done: error fetching connections: (25) Launch helper exited with unknown return code 1.

It is started with

ck-launch-session dbus-launch gnome-session

Offline

#9 2012-07-05 03:50:27

nomorewindows
Member
Registered: 2010-04-03
Posts: 3,362

Re: GDM and Gnome not working, showing only the cursor and wallpaper

liveag wrote:

I'm having the same problem too.
My X writes this:

X.Org X Server 1.12.2
Release Date: 2012-05-29
X Protocol Version 11, Revision 0
Build Operating System: Linux 3.0.32-1-lts x86_64 
Current Operating System: Linux guru 3.4.4-2-ARCH #1 SMP PREEMPT Sun Jun 24 18:59:47 CEST 2012 x86_64
Kernel command line: root=/dev/sdb1 ro vga=795
Build Date: 30 May 2012  07:24:13PM
 
Current version of pixman: 0.26.2
	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.1.log", Time: Thu Jul  5 06:14:45 2012
(==) Using config directory: "/etc/X11/xorg.conf.d"

(process:2265): Gtk-WARNING **: Locale not supported by C library.
	Using the fallback 'C' locale.

(process:2272): Gtk-WARNING **: Locale not supported by C library.
	Using the fallback 'C' locale.
GNOME_KEYRING_CONTROL=/home/gabriel/.cache/keyring-zOty4S
GPG_AGENT_INFO=/home/gabriel/.cache/keyring-zOty4S/gpg:0:1
GNOME_KEYRING_PID=2281

(process:2276): Gtk-WARNING **: Locale not supported by C library.
	Using the fallback 'C' locale.
GNOME_KEYRING_CONTROL=/home/gabriel/.cache/keyring-zOty4S
GPG_AGENT_INFO=/home/gabriel/.cache/keyring-zOty4S/gpg:0:1
SSH_AUTH_SOCK=/home/gabriel/.cache/keyring-zOty4S/ssh
GNOME_KEYRING_CONTROL=/home/gabriel/.cache/keyring-zOty4S
GPG_AGENT_INFO=/home/gabriel/.cache/keyring-zOty4S/gpg:0:1
SSH_AUTH_SOCK=/home/gabriel/.cache/keyring-zOty4S/ssh
GNOME_KEYRING_CONTROL=/home/gabriel/.cache/keyring-zOty4S
GPG_AGENT_INFO=/home/gabriel/.cache/keyring-zOty4S/gpg:0:1
SSH_AUTH_SOCK=/home/gabriel/.cache/keyring-zOty4S/ssh

(gnome-settings-daemon:2276): libupower-glib-WARNING **: Couldn't enumerate devices: Message did not receive a reply (timeout by message bus)

(gnome-settings-daemon:2276): power-plugin-WARNING **: failed to get device list: Message did not receive a reply (timeout by message bus)

(gnome-settings-daemon:2276): print-notifications-plugin-WARNING **: Unable to start print-notifications manager: Could not connect: No such file or directory

** (gnome-settings-daemon:2276): WARNING **: cannot connect to ConsoleKit: Could not connect: No such file or directory

(gnome-settings-daemon:2276): power-plugin-WARNING **: Could not connect to UPower: Could not connect: No such file or directory

(gnome-settings-daemon:2276): power-plugin-WARNING **: Could not connect to UPower: Could not connect: No such file or directory

** (gnome-settings-daemon:2276): WARNING **: cannot connect to ConsoleKit: Could not connect: No such file or directory

(gnome-settings-daemon:2276): color-plugin-WARNING **: failed to connect to colord: Could not connect: No such file or directory

(gnome-settings-daemon:2276): media-keys-plugin-WARNING **: Failed to get proxy for upower: Could not connect: No such file or directory
Window manager warning: Locale not understood by C library, internationalization will not work

(gnome-shell:2355): Clutter-WARNING **: Locale not supported by C library.
Using the fallback 'C' locale.

(gnome-shell:2355): Gtk-WARNING **: Locale not supported by C library.
	Using the fallback 'C' locale.
[1341461713,000,xklavier.c:xkl_engine_start_listen/] 	The backend does not require manual layout management - but it is provided by the application

(process:2362): Gtk-WARNING **: Locale not supported by C library.
	Using the fallback 'C' locale.

(process:2363): Gtk-WARNING **: Locale not supported by C library.
	Using the fallback 'C' locale.

(process:2365): Gtk-WARNING **: Locale not supported by C library.
	Using the fallback 'C' locale.

(process:2366): Gtk-WARNING **: Locale not supported by C library.
	Using the fallback 'C' locale.
The XKEYBOARD keymap compiler (xkbcomp) reports:
> Warning:          Compat map for group 2 redefined
>                   Using new definition
> Warning:          Compat map for group 3 redefined
>                   Using new definition
> Warning:          Compat map for group 4 redefined
>                   Using new definition
Errors from xkbcomp are not fatal to the X server
Failed to play sound: File or data not found

** (nm-applet:2363): WARNING **: Could not initialize NMClient /org/freedesktop/NetworkManager: Launch helper exited with unknown return code 1
** Message: applet now removed from the notification area

** (nm-applet:2363): WARNING **: fetch_connections_done: error fetching connections: (25) Launch helper exited with unknown return code 1.

It is started with

ck-launch-session dbus-launch gnome-session

This is your stderr/stdout messages, these aren't your /var/log/Xorg.0.log or dmesg output.


I may have to CONSOLE you about your usage of ridiculously easy graphical interfaces...
Look ma, no mouse.

Offline

#10 2012-07-05 14:53:43

mcapu
Member
Registered: 2012-07-02
Posts: 6

Re: GDM and Gnome not working, showing only the cursor and wallpaper

nomorewindows wrote:

How about your /var/log/Xorg.0.log or dmesg?

Hi, thanks for answering. My /var/log/Xorg.0.log is this one (I already checked for errors so I thought it wouldn't be needed, sorry):

[    18.049] 
X.Org X Server 1.12.2
Release Date: 2012-05-29
[    18.049] X Protocol Version 11, Revision 0
[    18.049] Build Operating System: Linux 3.0.32-1-lts x86_64 
[    18.049] Current Operating System: Linux mcapu 3.4.4-2-ARCH #1 SMP PREEMPT Sun Jun 24 18:59:47 CEST 2012 x86_64
[    18.049] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=2cf171c4-d86a-4d68-894e-d503cec468f1 ro quiet add_efi_memmap
[    18.049] Build Date: 30 May 2012  07:24:13PM
[    18.049]  
[    18.049] Current version of pixman: 0.26.2
[    18.049] 	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
[    18.049] Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    18.049] (==) Log file: "/var/log/Xorg.0.log", Time: Tue Jul  3 00:57:20 2012
[    18.082] (==) Using config file: "/etc/X11/xorg.conf"
[    18.082] (==) Using config directory: "/etc/X11/xorg.conf.d"
[    18.141] (==) ServerLayout "Layout0"
[    18.141] (**) |-->Screen "Screen0" (0)
[    18.141] (**) |   |-->Monitor "Monitor0"
[    18.142] (**) |   |-->Device "Device0"
[    18.142] (**) |-->Input Device "Keyboard0"
[    18.142] (**) |-->Input Device "Mouse0"
[    18.142] (**) Option "Xinerama" "0"
[    18.142] (==) Automatically adding devices
[    18.142] (==) Automatically enabling devices
[    18.191] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[    18.192] 	Entry deleted from font path.
[    18.231] (==) FontPath set to:
	/usr/share/fonts/misc/,
	/usr/share/fonts/TTF/,
	/usr/share/fonts/Type1/,
	/usr/share/fonts/100dpi/,
	/usr/share/fonts/75dpi/
[    18.231] (==) ModulePath set to "/usr/lib/xorg/modules"
[    18.231] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
[    18.231] (WW) Disabling Keyboard0
[    18.231] (WW) Disabling Mouse0
[    18.231] (II) Loader magic: 0x7c58e0
[    18.231] (II) Module ABI versions:
[    18.231] 	X.Org ANSI C Emulation: 0.4
[    18.231] 	X.Org Video Driver: 12.0
[    18.231] 	X.Org XInput driver : 16.0
[    18.231] 	X.Org Server Extension : 6.0
[    18.232] (--) PCI:*(0:1:0:0) 10de:0649:1025:0146 rev 161, Mem @ 0xd2000000/16777216, 0xc0000000/268435456, 0xd0000000/33554432, I/O @ 0x00006000/128
[    18.233] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[    18.233] (II) LoadModule: "extmod"
[    18.242] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[    18.250] (II) Module extmod: vendor="X.Org Foundation"
[    18.250] 	compiled for 1.12.2, module version = 1.0.0
[    18.250] 	Module class: X.Org Server Extension
[    18.250] 	ABI class: X.Org Server Extension, version 6.0
[    18.250] (II) Loading extension MIT-SCREEN-SAVER
[    18.250] (II) Loading extension XFree86-VidModeExtension
[    18.250] (II) Loading extension XFree86-DGA
[    18.250] (II) Loading extension DPMS
[    18.250] (II) Loading extension XVideo
[    18.250] (II) Loading extension XVideo-MotionCompensation
[    18.250] (II) Loading extension X-Resource
[    18.250] (II) LoadModule: "dbe"
[    18.250] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[    18.255] (II) Module dbe: vendor="X.Org Foundation"
[    18.255] 	compiled for 1.12.2, module version = 1.0.0
[    18.255] 	Module class: X.Org Server Extension
[    18.255] 	ABI class: X.Org Server Extension, version 6.0
[    18.255] (II) Loading extension DOUBLE-BUFFER
[    18.255] (II) LoadModule: "glx"
[    18.255] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[    19.077] (II) Module glx: vendor="NVIDIA Corporation"
[    19.077] 	compiled for 4.0.2, module version = 1.0.0
[    19.077] 	Module class: X.Org Server Extension
[    19.077] (II) NVIDIA GLX Module  302.17  Tue Jun 12 16:22:45 PDT 2012
[    19.077] (II) Loading extension GLX
[    19.077] (II) LoadModule: "record"
[    19.078] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[    19.092] (II) Module record: vendor="X.Org Foundation"
[    19.092] 	compiled for 1.12.2, module version = 1.13.0
[    19.093] 	Module class: X.Org Server Extension
[    19.093] 	ABI class: X.Org Server Extension, version 6.0
[    19.093] (II) Loading extension RECORD
[    19.093] (II) LoadModule: "dri"
[    19.093] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[    19.108] (II) Module dri: vendor="X.Org Foundation"
[    19.108] 	compiled for 1.12.2, module version = 1.0.0
[    19.108] 	ABI class: X.Org Server Extension, version 6.0
[    19.108] (II) Loading extension XFree86-DRI
[    19.108] (II) LoadModule: "dri2"
[    19.109] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[    19.110] (II) Module dri2: vendor="X.Org Foundation"
[    19.110] 	compiled for 1.12.2, module version = 1.2.0
[    19.110] 	ABI class: X.Org Server Extension, version 6.0
[    19.110] (II) Loading extension DRI2
[    19.110] (II) LoadModule: "nvidia"
[    19.120] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
[    19.228] (II) Module nvidia: vendor="NVIDIA Corporation"
[    19.228] 	compiled for 4.0.2, module version = 1.0.0
[    19.228] 	Module class: X.Org Video Driver
[    19.256] (II) NVIDIA dlloader X Driver  302.17  Tue Jun 12 16:04:53 PDT 2012
[    19.256] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
[    19.257] (++) using VT number 7

[    19.410] (II) Loading sub module "fb"
[    19.410] (II) LoadModule: "fb"
[    19.414] (II) Loading /usr/lib/xorg/modules/libfb.so
[    19.438] (II) Module fb: vendor="X.Org Foundation"
[    19.438] 	compiled for 1.12.2, module version = 1.0.0
[    19.438] 	ABI class: X.Org ANSI C Emulation, version 0.4
[    19.438] (II) Loading sub module "wfb"
[    19.438] (II) LoadModule: "wfb"
[    19.439] (II) Loading /usr/lib/xorg/modules/libwfb.so
[    19.453] (II) Module wfb: vendor="X.Org Foundation"
[    19.453] 	compiled for 1.12.2, module version = 1.0.0
[    19.453] 	ABI class: X.Org ANSI C Emulation, version 0.4
[    19.453] (II) Loading sub module "ramdac"
[    19.453] (II) LoadModule: "ramdac"
[    19.453] (II) Module "ramdac" already built-in
[    19.479] (**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32
[    19.479] (==) NVIDIA(0): RGB weight 888
[    19.479] (==) NVIDIA(0): Default visual is TrueColor
[    19.479] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
[    19.479] (**) NVIDIA(0): Option "Stereo" "0"
[    19.479] (**) NVIDIA(0): Option "nvidiaXineramaInfoOrder" "CRT-0"
[    19.480] (**) NVIDIA(0): Stereo disabled by request
[    19.480] (**) NVIDIA(0): Option "MetaModes" "CRT: nvidia-auto-select +0+0"
[    19.480] (**) NVIDIA(0): Enabling 2D acceleration
[    21.747] (II) NVIDIA(GPU-0): Display (BenQ BL2400 (CRT-0)) does not support NVIDIA 3D
[    21.747] (II) NVIDIA(GPU-0):     Vision stereo.
[    21.747] (II) NVIDIA(GPU-0): Display (Seiko/Epson (DFP-0)) does not support NVIDIA 3D
[    21.747] (II) NVIDIA(GPU-0):     Vision stereo.
[    21.751] (II) NVIDIA(0): NVIDIA GPU GeForce 9600M GT (G96) at PCI:1:0:0 (GPU-0)
[    21.751] (--) NVIDIA(0): Memory: 524288 kBytes
[    21.751] (--) NVIDIA(0): VideoBIOS: 62.94.38.00.04
[    21.751] (II) NVIDIA(0): Detected PCI Express Link width: 16X
[    21.751] (--) NVIDIA(0): Interlaced video modes are supported on this GPU
[    21.755] (--) NVIDIA(0): Valid display device(s) on GeForce 9600M GT at PCI:1:0:0
[    21.755] (--) NVIDIA(0):     BenQ BL2400 (CRT-0) (connected)
[    21.755] (--) NVIDIA(0):     Seiko/Epson (DFP-0) (connected)
[    21.755] (--) NVIDIA(0):     DFP-1
[    21.755] (--) NVIDIA(0):     DFP-3
[    21.755] (--) NVIDIA(0): BenQ BL2400 (CRT-0): 400.0 MHz maximum pixel clock
[    21.755] (--) NVIDIA(0): Seiko/Epson (DFP-0): 330.0 MHz maximum pixel clock
[    21.755] (--) NVIDIA(0): Seiko/Epson (DFP-0): Internal Dual Link LVDS
[    21.755] (--) NVIDIA(0): DFP-1: 165.0 MHz maximum pixel clock
[    21.755] (--) NVIDIA(0): DFP-1: Internal Single Link TMDS
[    21.755] (--) NVIDIA(0): DFP-3: 480.0 MHz maximum pixel clock
[    21.755] (--) NVIDIA(0): DFP-3: Internal DisplayPort
[    21.755] (**) NVIDIA(0): Using HorizSync/VertRefresh ranges from the EDID for display
[    21.755] (**) NVIDIA(0):     device BenQ BL2400 (CRT-0) (Using EDID frequencies has
[    21.755] (**) NVIDIA(0):     been enabled on all display devices.)
[    21.774] (**) NVIDIA(0): Using HorizSync/VertRefresh ranges from the EDID for display
[    21.774] (**) NVIDIA(0):     device Seiko/Epson (DFP-0) (Using EDID frequencies has
[    21.774] (**) NVIDIA(0):     been enabled on all display devices.)
[    21.774] (II) NVIDIA(0): Validated modes:
[    21.774] (II) NVIDIA(0):     "CRT:nvidia-auto-select+0+0"
[    21.774] (II) NVIDIA(0): Virtual screen size determined to be 1920 x 1080
[    21.798] (--) NVIDIA(0): DPI set to (92, 91); computed from "UseEdidDpi" X config
[    21.798] (--) NVIDIA(0):     option
[    21.798] (--) Depth 24 pixmap format is 32 bpp
[    21.799] (II) NVIDIA: Using 768.00 MB of virtual memory for indirect memory access.
[    21.806] (II) NVIDIA(0): ACPI: failed to connect to the ACPI event daemon; the daemon
[    21.806] (II) NVIDIA(0):     may not be running or the "AcpidSocketPath" X
[    21.806] (II) NVIDIA(0):     configuration option may not be set correctly.  When the
[    21.806] (II) NVIDIA(0):     ACPI event daemon is available, the NVIDIA X driver will
[    21.806] (II) NVIDIA(0):     try to use it to receive ACPI event notifications.  For
[    21.806] (II) NVIDIA(0):     details, please see the "ConnectToAcpid" and
[    21.806] (II) NVIDIA(0):     "AcpidSocketPath" X configuration options in Appendix B: X
[    21.806] (II) NVIDIA(0):     Config Options in the README.
[    21.809] (II) NVIDIA(0): Setting mode "CRT:nvidia-auto-select+0+0"
[    21.853] (II) Loading extension NV-GLX
[    21.918] (==) NVIDIA(0): Disabling shared memory pixmaps
[    21.918] (==) NVIDIA(0): Backing store disabled
[    21.918] (==) NVIDIA(0): Silken mouse enabled
[    21.918] (**) NVIDIA(0): DPMS enabled
[    21.918] (II) Loading extension NV-CONTROL
[    21.919] (II) Loading extension XINERAMA
[    21.919] (II) Loading sub module "dri2"
[    21.919] (II) LoadModule: "dri2"
[    21.919] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[    21.919] (II) Module dri2: vendor="X.Org Foundation"
[    21.919] 	compiled for 1.12.2, module version = 1.2.0
[    21.919] 	ABI class: X.Org Server Extension, version 6.0
[    21.919] (II) NVIDIA(0): [DRI2] Setup complete
[    21.919] (II) NVIDIA(0): [DRI2]   VDPAU driver: nvidia
[    21.919] (--) RandR disabled
[    21.919] (II) Initializing built-in extension Generic Event Extension
[    21.919] (II) Initializing built-in extension SHAPE
[    21.919] (II) Initializing built-in extension MIT-SHM
[    21.919] (II) Initializing built-in extension XInputExtension
[    21.919] (II) Initializing built-in extension XTEST
[    21.919] (II) Initializing built-in extension BIG-REQUESTS
[    21.919] (II) Initializing built-in extension SYNC
[    21.919] (II) Initializing built-in extension XKEYBOARD
[    21.919] (II) Initializing built-in extension XC-MISC
[    21.919] (II) Initializing built-in extension SECURITY
[    21.919] (II) Initializing built-in extension XINERAMA
[    21.919] (II) Initializing built-in extension XFIXES
[    21.919] (II) Initializing built-in extension RENDER
[    21.919] (II) Initializing built-in extension RANDR
[    21.919] (II) Initializing built-in extension COMPOSITE
[    21.919] (II) Initializing built-in extension DAMAGE
[    21.921] (II) Initializing extension GLX
[    22.438] (II) config/udev: Adding input device Power Button (/dev/input/event4)
[    22.439] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    22.439] (II) LoadModule: "evdev"
[    22.439] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    22.458] (II) Module evdev: vendor="X.Org Foundation"
[    22.458] 	compiled for 1.12.0, module version = 2.7.0
[    22.458] 	Module class: X.Org XInput Driver
[    22.458] 	ABI class: X.Org XInput driver, version 16.0
[    22.458] (II) Using input driver 'evdev' for 'Power Button'
[    22.458] (**) Power Button: always reports core events
[    22.458] (**) evdev: Power Button: Device: "/dev/input/event4"
[    22.458] (--) evdev: Power Button: Vendor 0 Product 0x1
[    22.458] (--) evdev: Power Button: Found keys
[    22.458] (II) evdev: Power Button: Configuring as keyboard
[    22.458] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4/event4"
[    22.458] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[    22.458] (**) Option "xkb_rules" "evdev"
[    22.458] (**) Option "xkb_model" "evdev"
[    22.458] (**) Option "xkb_layout" "us"
[    22.490] (II) config/udev: Adding input device Video Bus (/dev/input/event6)
[    22.490] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[    22.490] (II) Using input driver 'evdev' for 'Video Bus'
[    22.490] (**) Video Bus: always reports core events
[    22.490] (**) evdev: Video Bus: Device: "/dev/input/event6"
[    22.490] (--) evdev: Video Bus: Vendor 0 Product 0x6
[    22.490] (--) evdev: Video Bus: Found keys
[    22.490] (II) evdev: Video Bus: Configuring as keyboard
[    22.490] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input6/event6"
[    22.490] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[    22.490] (**) Option "xkb_rules" "evdev"
[    22.490] (**) Option "xkb_model" "evdev"
[    22.490] (**) Option "xkb_layout" "us"
[    22.490] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[    22.490] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    22.490] (II) Using input driver 'evdev' for 'Power Button'
[    22.490] (**) Power Button: always reports core events
[    22.490] (**) evdev: Power Button: Device: "/dev/input/event2"
[    22.490] (--) evdev: Power Button: Vendor 0 Product 0x1
[    22.490] (--) evdev: Power Button: Found keys
[    22.490] (II) evdev: Power Button: Configuring as keyboard
[    22.490] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2/event2"
[    22.490] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[    22.490] (**) Option "xkb_rules" "evdev"
[    22.490] (**) Option "xkb_model" "evdev"
[    22.490] (**) Option "xkb_layout" "us"
[    22.491] (II) config/udev: Adding input device Lid Switch (/dev/input/event3)
[    22.491] (II) No input driver specified, ignoring this device.
[    22.491] (II) This device may have been added with another device file.
[    22.491] (II) config/udev: Adding input device Sleep Button (/dev/input/event1)
[    22.491] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[    22.491] (II) Using input driver 'evdev' for 'Sleep Button'
[    22.491] (**) Sleep Button: always reports core events
[    22.491] (**) evdev: Sleep Button: Device: "/dev/input/event1"
[    22.491] (--) evdev: Sleep Button: Vendor 0 Product 0x3
[    22.491] (--) evdev: Sleep Button: Found keys
[    22.491] (II) evdev: Sleep Button: Configuring as keyboard
[    22.491] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1/event1"
[    22.491] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 9)
[    22.491] (**) Option "xkb_rules" "evdev"
[    22.491] (**) Option "xkb_model" "evdev"
[    22.491] (**) Option "xkb_layout" "us"
[    22.492] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event15)
[    22.492] (II) No input driver specified, ignoring this device.
[    22.492] (II) This device may have been added with another device file.
[    22.492] (II) config/udev: Adding input device HDA Intel Line (/dev/input/event17)
[    22.492] (II) No input driver specified, ignoring this device.
[    22.492] (II) This device may have been added with another device file.
[    22.492] (II) config/udev: Adding input device HDA Intel Mic (/dev/input/event18)
[    22.492] (II) No input driver specified, ignoring this device.
[    22.492] (II) This device may have been added with another device file.
[    22.492] (II) config/udev: Adding input device HDA Intel Front Headphone (/dev/input/event19)
[    22.492] (II) No input driver specified, ignoring this device.
[    22.492] (II) This device may have been added with another device file.
[    22.493] (II) config/udev: Adding input device Microsoft Wired Keyboard 600 (/dev/input/event8)
[    22.493] (**) Microsoft Wired Keyboard 600: Applying InputClass "evdev keyboard catchall"
[    22.493] (II) Using input driver 'evdev' for 'Microsoft Wired Keyboard 600'
[    22.493] (**) Microsoft Wired Keyboard 600: always reports core events
[    22.493] (**) evdev: Microsoft Wired Keyboard 600: Device: "/dev/input/event8"
[    22.493] (--) evdev: Microsoft Wired Keyboard 600: Vendor 0x45e Product 0x750
[    22.493] (--) evdev: Microsoft Wired Keyboard 600: Found keys
[    22.493] (II) evdev: Microsoft Wired Keyboard 600: Configuring as keyboard
[    22.493] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.0/input/input8/event8"
[    22.493] (II) XINPUT: Adding extended input device "Microsoft Wired Keyboard 600" (type: KEYBOARD, id 10)
[    22.493] (**) Option "xkb_rules" "evdev"
[    22.493] (**) Option "xkb_model" "evdev"
[    22.493] (**) Option "xkb_layout" "us"
[    22.493] (II) config/udev: Adding input device Microsoft Wired Keyboard 600 (/dev/input/event9)
[    22.493] (**) Microsoft Wired Keyboard 600: Applying InputClass "evdev keyboard catchall"
[    22.493] (II) Using input driver 'evdev' for 'Microsoft Wired Keyboard 600'
[    22.493] (**) Microsoft Wired Keyboard 600: always reports core events
[    22.493] (**) evdev: Microsoft Wired Keyboard 600: Device: "/dev/input/event9"
[    22.493] (--) evdev: Microsoft Wired Keyboard 600: Vendor 0x45e Product 0x750
[    22.493] (--) evdev: Microsoft Wired Keyboard 600: Found 1 mouse buttons
[    22.493] (--) evdev: Microsoft Wired Keyboard 600: Found scroll wheel(s)
[    22.493] (--) evdev: Microsoft Wired Keyboard 600: Found relative axes
[    22.493] (--) evdev: Microsoft Wired Keyboard 600: Found absolute axes
[    22.493] (--) evdev: Microsoft Wired Keyboard 600: Found x and y absolute axes
[    22.493] (--) evdev: Microsoft Wired Keyboard 600: Found keys
[    22.493] (II) evdev: Microsoft Wired Keyboard 600: Configuring as mouse
[    22.493] (II) evdev: Microsoft Wired Keyboard 600: Configuring as keyboard
[    22.493] (II) evdev: Microsoft Wired Keyboard 600: Adding scrollwheel support
[    22.494] (**) evdev: Microsoft Wired Keyboard 600: YAxisMapping: buttons 4 and 5
[    22.494] (**) evdev: Microsoft Wired Keyboard 600: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    22.494] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.1/input/input9/event9"
[    22.494] (II) XINPUT: Adding extended input device "Microsoft Wired Keyboard 600" (type: KEYBOARD, id 11)
[    22.494] (**) Option "xkb_rules" "evdev"
[    22.494] (**) Option "xkb_model" "evdev"
[    22.494] (**) Option "xkb_layout" "us"
[    22.494] (II) evdev: Microsoft Wired Keyboard 600: initialized for relative axes.
[    22.494] (WW) evdev: Microsoft Wired Keyboard 600: ignoring absolute axes.
[    22.494] (**) Microsoft Wired Keyboard 600: (accel) keeping acceleration scheme 1
[    22.494] (**) Microsoft Wired Keyboard 600: (accel) acceleration profile 0
[    22.494] (**) Microsoft Wired Keyboard 600: (accel) acceleration factor: 2.000
[    22.494] (**) Microsoft Wired Keyboard 600: (accel) acceleration threshold: 4
[    22.494] (II) config/udev: Adding input device Microsoft Wired Keyboard 600 (/dev/input/js0)
[    22.494] (II) No input driver specified, ignoring this device.
[    22.494] (II) This device may have been added with another device file.
[    22.494] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/event10)
[    22.494] (**) Logitech USB Receiver: Applying InputClass "evdev pointer catchall"
[    22.494] (II) Using input driver 'evdev' for 'Logitech USB Receiver'
[    22.495] (**) Logitech USB Receiver: always reports core events
[    22.495] (**) evdev: Logitech USB Receiver: Device: "/dev/input/event10"
[    22.495] (--) evdev: Logitech USB Receiver: Vendor 0x46d Product 0xc51a
[    22.495] (--) evdev: Logitech USB Receiver: Found 20 mouse buttons
[    22.495] (--) evdev: Logitech USB Receiver: Found scroll wheel(s)
[    22.495] (--) evdev: Logitech USB Receiver: Found relative axes
[    22.495] (--) evdev: Logitech USB Receiver: Found x and y relative axes
[    22.495] (II) evdev: Logitech USB Receiver: Configuring as mouse
[    22.495] (II) evdev: Logitech USB Receiver: Adding scrollwheel support
[    22.495] (**) evdev: Logitech USB Receiver: YAxisMapping: buttons 4 and 5
[    22.495] (**) evdev: Logitech USB Receiver: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    22.495] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input10/event10"
[    22.495] (II) XINPUT: Adding extended input device "Logitech USB Receiver" (type: MOUSE, id 12)
[    22.495] (II) evdev: Logitech USB Receiver: initialized for relative axes.
[    22.495] (**) Logitech USB Receiver: (accel) keeping acceleration scheme 1
[    22.495] (**) Logitech USB Receiver: (accel) acceleration profile 0
[    22.495] (**) Logitech USB Receiver: (accel) acceleration factor: 2.000
[    22.495] (**) Logitech USB Receiver: (accel) acceleration threshold: 4
[    22.495] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/mouse0)
[    22.495] (II) No input driver specified, ignoring this device.
[    22.495] (II) This device may have been added with another device file.
[    22.495] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/event11)
[    22.495] (**) Logitech USB Receiver: Applying InputClass "evdev keyboard catchall"
[    22.495] (II) Using input driver 'evdev' for 'Logitech USB Receiver'
[    22.495] (**) Logitech USB Receiver: always reports core events
[    22.496] (**) evdev: Logitech USB Receiver: Device: "/dev/input/event11"
[    22.496] (--) evdev: Logitech USB Receiver: Vendor 0x46d Product 0xc51a
[    22.496] (--) evdev: Logitech USB Receiver: Found 1 mouse buttons
[    22.496] (--) evdev: Logitech USB Receiver: Found scroll wheel(s)
[    22.496] (--) evdev: Logitech USB Receiver: Found relative axes
[    22.496] (II) evdev: Logitech USB Receiver: Forcing relative x/y axes to exist.
[    22.496] (--) evdev: Logitech USB Receiver: Found absolute axes
[    22.496] (II) evdev: Logitech USB Receiver: Forcing absolute x/y axes to exist.
[    22.496] (--) evdev: Logitech USB Receiver: Found keys
[    22.496] (II) evdev: Logitech USB Receiver: Configuring as mouse
[    22.496] (II) evdev: Logitech USB Receiver: Configuring as keyboard
[    22.496] (II) evdev: Logitech USB Receiver: Adding scrollwheel support
[    22.496] (**) evdev: Logitech USB Receiver: YAxisMapping: buttons 4 and 5
[    22.496] (**) evdev: Logitech USB Receiver: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    22.496] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input11/event11"
[    22.496] (II) XINPUT: Adding extended input device "Logitech USB Receiver" (type: KEYBOARD, id 13)
[    22.496] (**) Option "xkb_rules" "evdev"
[    22.496] (**) Option "xkb_model" "evdev"
[    22.496] (**) Option "xkb_layout" "us"
[    22.496] (II) evdev: Logitech USB Receiver: initialized for relative axes.
[    22.496] (WW) evdev: Logitech USB Receiver: ignoring absolute axes.
[    22.496] (**) Logitech USB Receiver: (accel) keeping acceleration scheme 1
[    22.496] (**) Logitech USB Receiver: (accel) acceleration profile 0
[    22.496] (**) Logitech USB Receiver: (accel) acceleration factor: 2.000
[    22.496] (**) Logitech USB Receiver: (accel) acceleration threshold: 4
[    22.496] (II) config/udev: Adding input device PS/2+USB Mouse (/dev/input/event12)
[    22.496] (**) PS/2+USB Mouse: Applying InputClass "evdev pointer catchall"
[    22.496] (II) Using input driver 'evdev' for 'PS/2+USB Mouse'
[    22.496] (**) PS/2+USB Mouse: always reports core events
[    22.496] (**) evdev: PS/2+USB Mouse: Device: "/dev/input/event12"
[    22.496] (--) evdev: PS/2+USB Mouse: Vendor 0x4f3 Product 0x212
[    22.496] (--) evdev: PS/2+USB Mouse: Found 9 mouse buttons
[    22.496] (--) evdev: PS/2+USB Mouse: Found scroll wheel(s)
[    22.497] (--) evdev: PS/2+USB Mouse: Found relative axes
[    22.497] (--) evdev: PS/2+USB Mouse: Found x and y relative axes
[    22.497] (II) evdev: PS/2+USB Mouse: Configuring as mouse
[    22.497] (II) evdev: PS/2+USB Mouse: Adding scrollwheel support
[    22.497] (**) evdev: PS/2+USB Mouse: YAxisMapping: buttons 4 and 5
[    22.497] (**) evdev: PS/2+USB Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    22.497] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.1/usb6/6-2/6-2:1.0/input/input12/event12"
[    22.497] (II) XINPUT: Adding extended input device "PS/2+USB Mouse" (type: MOUSE, id 14)
[    22.497] (II) evdev: PS/2+USB Mouse: initialized for relative axes.
[    22.497] (**) PS/2+USB Mouse: (accel) keeping acceleration scheme 1
[    22.497] (**) PS/2+USB Mouse: (accel) acceleration profile 0
[    22.497] (**) PS/2+USB Mouse: (accel) acceleration factor: 2.000
[    22.497] (**) PS/2+USB Mouse: (accel) acceleration threshold: 4
[    22.497] (II) config/udev: Adding input device PS/2+USB Mouse (/dev/input/mouse1)
[    22.497] (II) No input driver specified, ignoring this device.
[    22.497] (II) This device may have been added with another device file.
[    22.497] (II) config/udev: Adding input device Acer HD Crystal Eye webcam (/dev/input/event13)
[    22.497] (**) Acer HD Crystal Eye webcam: Applying InputClass "evdev keyboard catchall"
[    22.497] (II) Using input driver 'evdev' for 'Acer HD Crystal Eye webcam'
[    22.497] (**) Acer HD Crystal Eye webcam: always reports core events
[    22.497] (**) evdev: Acer HD Crystal Eye webcam: Device: "/dev/input/event13"
[    22.497] (--) evdev: Acer HD Crystal Eye webcam: Vendor 0x64e Product 0xa117
[    22.497] (--) evdev: Acer HD Crystal Eye webcam: Found keys
[    22.497] (II) evdev: Acer HD Crystal Eye webcam: Configuring as keyboard
[    22.497] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-6/2-6:1.0/input/input13/event13"
[    22.497] (II) XINPUT: Adding extended input device "Acer HD Crystal Eye webcam" (type: KEYBOARD, id 15)
[    22.497] (**) Option "xkb_rules" "evdev"
[    22.497] (**) Option "xkb_model" "evdev"
[    22.497] (**) Option "xkb_layout" "us"
[    22.498] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[    22.498] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[    22.498] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[    22.498] (**) AT Translated Set 2 keyboard: always reports core events
[    22.498] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[    22.498] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[    22.498] (--) evdev: AT Translated Set 2 keyboard: Found keys
[    22.498] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[    22.498] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[    22.498] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 16)
[    22.498] (**) Option "xkb_rules" "evdev"
[    22.498] (**) Option "xkb_model" "evdev"
[    22.498] (**) Option "xkb_layout" "us"
[    22.498] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event16)
[    22.498] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "evdev touchpad catchall"
[    22.498] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "touchpad catchall"
[    22.498] (II) LoadModule: "synaptics"
[    22.499] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[    22.515] (II) Module synaptics: vendor="X.Org Foundation"
[    22.515] 	compiled for 1.12.2, module version = 1.6.2
[    22.515] 	Module class: X.Org XInput Driver
[    22.515] 	ABI class: X.Org XInput driver, version 16.0
[    22.515] (II) Using input driver 'synaptics' for 'SynPS/2 Synaptics TouchPad'
[    22.515] (**) SynPS/2 Synaptics TouchPad: always reports core events
[    22.515] (**) Option "Device" "/dev/input/event16"
[    22.515] (--) synaptics: SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5472
[    22.515] (--) synaptics: SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4448
[    22.515] (--) synaptics: SynPS/2 Synaptics TouchPad: pressure range 0 - 255
[    22.515] (--) synaptics: SynPS/2 Synaptics TouchPad: finger width range 0 - 15
[    22.515] (--) synaptics: SynPS/2 Synaptics TouchPad: buttons: left right scroll-buttons
[    22.515] (--) synaptics: SynPS/2 Synaptics TouchPad: Vendor 0x2 Product 0x7
[    22.515] (**) Option "TapButton1" "1"
[    22.515] (**) Option "TapButton2" "2"
[    22.515] (**) Option "TapButton3" "3"
[    22.515] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[    22.515] (**) SynPS/2 Synaptics TouchPad: always reports core events
[    22.515] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio2/input/input16/event16"
[    22.515] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD, id 17)
[    22.515] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) MinSpeed is now constant deceleration 2.5
[    22.515] (**) synaptics: SynPS/2 Synaptics TouchPad: MaxSpeed is now 1.75
[    22.515] (**) synaptics: SynPS/2 Synaptics TouchPad: AccelFactor is now 0.040
[    22.516] (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
[    22.516] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 1
[    22.516] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[    22.516] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[    22.516] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[    22.516] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse3)
[    22.516] (II) No input driver specified, ignoring this device.
[    22.516] (II) This device may have been added with another device file.
[    22.516] (II) config/udev: Adding input device PC Speaker (/dev/input/event5)
[    22.516] (II) No input driver specified, ignoring this device.
[    22.516] (II) This device may have been added with another device file.
[    22.517] (II) config/udev: Adding input device MCE IR Keyboard/Mouse (ite-cir) (/dev/input/event14)
[    22.517] (**) MCE IR Keyboard/Mouse (ite-cir): Applying InputClass "evdev pointer catchall"
[    22.517] (**) MCE IR Keyboard/Mouse (ite-cir): Applying InputClass "evdev keyboard catchall"
[    22.517] (II) Using input driver 'evdev' for 'MCE IR Keyboard/Mouse (ite-cir)'
[    22.517] (**) MCE IR Keyboard/Mouse (ite-cir): always reports core events
[    22.517] (**) evdev: MCE IR Keyboard/Mouse (ite-cir): Device: "/dev/input/event14"
[    22.517] (--) evdev: MCE IR Keyboard/Mouse (ite-cir): Vendor 0 Product 0
[    22.517] (--) evdev: MCE IR Keyboard/Mouse (ite-cir): Found 3 mouse buttons
[    22.517] (--) evdev: MCE IR Keyboard/Mouse (ite-cir): Found relative axes
[    22.517] (--) evdev: MCE IR Keyboard/Mouse (ite-cir): Found x and y relative axes
[    22.517] (--) evdev: MCE IR Keyboard/Mouse (ite-cir): Found keys
[    22.517] (II) evdev: MCE IR Keyboard/Mouse (ite-cir): Configuring as mouse
[    22.517] (II) evdev: MCE IR Keyboard/Mouse (ite-cir): Configuring as keyboard
[    22.517] (**) evdev: MCE IR Keyboard/Mouse (ite-cir): YAxisMapping: buttons 4 and 5
[    22.517] (**) evdev: MCE IR Keyboard/Mouse (ite-cir): EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    22.517] (**) Option "config_info" "udev:/sys/devices/virtual/input/input14/event14"
[    22.517] (II) XINPUT: Adding extended input device "MCE IR Keyboard/Mouse (ite-cir)" (type: KEYBOARD, id 18)
[    22.517] (**) Option "xkb_rules" "evdev"
[    22.517] (**) Option "xkb_model" "evdev"
[    22.517] (**) Option "xkb_layout" "us"
[    22.517] (II) evdev: MCE IR Keyboard/Mouse (ite-cir): initialized for relative axes.
[    22.517] (**) MCE IR Keyboard/Mouse (ite-cir): (accel) keeping acceleration scheme 1
[    22.517] (**) MCE IR Keyboard/Mouse (ite-cir): (accel) acceleration profile 0
[    22.517] (**) MCE IR Keyboard/Mouse (ite-cir): (accel) acceleration factor: 2.000
[    22.517] (**) MCE IR Keyboard/Mouse (ite-cir): (accel) acceleration threshold: 4
[    22.517] (II) config/udev: Adding input device MCE IR Keyboard/Mouse (ite-cir) (/dev/input/mouse2)
[    22.517] (II) No input driver specified, ignoring this device.
[    22.517] (II) This device may have been added with another device file.
[    22.518] (II) config/udev: Adding input device ITE8708 CIR transceiver (/dev/input/event7)
[    22.518] (**) ITE8708 CIR transceiver: Applying InputClass "evdev keyboard catchall"
[    22.518] (II) Using input driver 'evdev' for 'ITE8708 CIR transceiver'
[    22.518] (**) ITE8708 CIR transceiver: always reports core events
[    22.518] (**) evdev: ITE8708 CIR transceiver: Device: "/dev/input/event7"
[    22.518] (--) evdev: ITE8708 CIR transceiver: Vendor 0x1283 Product 0
[    22.518] (--) evdev: ITE8708 CIR transceiver: Found keys
[    22.518] (II) evdev: ITE8708 CIR transceiver: Configuring as keyboard
[    22.518] (**) Option "config_info" "udev:/sys/devices/virtual/rc/rc0/input7/event7"
[    22.518] (II) XINPUT: Adding extended input device "ITE8708 CIR transceiver" (type: KEYBOARD, id 19)
[    22.518] (**) Option "xkb_rules" "evdev"
[    22.518] (**) Option "xkb_model" "evdev"
[    22.518] (**) Option "xkb_layout" "us"
[    75.752] (II) evdev: ITE8708 CIR transceiver: Close
[    75.753] (II) UnloadModule: "evdev"
[    75.753] (II) evdev: MCE IR Keyboard/Mouse (ite-cir): Close
[    75.753] (II) UnloadModule: "evdev"
[    75.753] (II) UnloadModule: "synaptics"
[    75.753] (II) evdev: AT Translated Set 2 keyboard: Close
[    75.753] (II) UnloadModule: "evdev"
[    75.753] (II) evdev: Acer HD Crystal Eye webcam: Close
[    75.753] (II) UnloadModule: "evdev"
[    75.753] (II) evdev: PS/2+USB Mouse: Close
[    75.753] (II) UnloadModule: "evdev"
[    75.753] (II) evdev: Logitech USB Receiver: Close
[    75.753] (II) UnloadModule: "evdev"
[    75.753] (II) evdev: Logitech USB Receiver: Close
[    75.753] (II) UnloadModule: "evdev"
[    75.753] (II) evdev: Microsoft Wired Keyboard 600: Close
[    75.753] (II) UnloadModule: "evdev"
[    75.753] (II) evdev: Microsoft Wired Keyboard 600: Close
[    75.753] (II) UnloadModule: "evdev"
[    75.753] (II) evdev: Sleep Button: Close
[    75.753] (II) UnloadModule: "evdev"
[    75.753] (II) evdev: Power Button: Close
[    75.753] (II) UnloadModule: "evdev"
[    75.753] (II) evdev: Video Bus: Close
[    75.753] (II) UnloadModule: "evdev"
[    75.753] (II) evdev: Power Button: Close
[    75.753] (II) UnloadModule: "evdev"
[    75.874] Server terminated successfully (0). Closing log file.

Offline

#11 2012-07-06 01:59:45

nomorewindows
Member
Registered: 2010-04-03
Posts: 3,362

Re: GDM and Gnome not working, showing only the cursor and wallpaper

I don't see anything either in your Xorg.0.log how about your dmesg output?
Seems as though there is a strange problem between gnome and video drivers not sure what it is.


I may have to CONSOLE you about your usage of ridiculously easy graphical interfaces...
Look ma, no mouse.

Offline

#12 2012-07-06 17:23:55

mcapu
Member
Registered: 2012-07-02
Posts: 6

Re: GDM and Gnome not working, showing only the cursor and wallpaper

nomorewindows wrote:

I don't see anything either in your Xorg.0.log how about your dmesg output?
Seems as though there is a strange problem between gnome and video drivers not sure what it is.

Thanks, this is the dmesg.log:

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.4.4-2-ARCH (tobias@T-POWA-LX) (gcc version 4.7.1 (GCC) ) #1 SMP PREEMPT Sun Jun 24 18:59:47 CEST 2012
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=2cf171c4-d86a-4d68-894e-d503cec468f1 ro quiet add_efi_memmap
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009e000 (usable)
[    0.000000]  BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000bfc69000 (usable)
[    0.000000]  BIOS-e820: 00000000bfc69000 - 00000000bfcbf000 (reserved)
[    0.000000]  BIOS-e820: 00000000bfcbf000 - 00000000bfd82000 (usable)
[    0.000000]  BIOS-e820: 00000000bfd82000 - 00000000bfdbf000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000bfdbf000 - 00000000bfdeb000 (usable)
[    0.000000]  BIOS-e820: 00000000bfdeb000 - 00000000bfdff000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000bfdff000 - 00000000bfe00000 (usable)
[    0.000000]  BIOS-e820: 00000000bfe00000 - 00000000c0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed10000 - 00000000fed14000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed18000 - 00000000fed1a000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[    0.000000]  BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] DMI 2.4 present.
[    0.000000] DMI: Acer Aspire 6935/Aspire 6935, BIOS V1.21 03/03/2011
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] No AGP bridge found
[    0.000000] last_pfn = 0x140000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-DFFFF write-protect
[    0.000000]   E0000-EFFFF uncachable
[    0.000000]   F0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 0FFFA0000 mask FFFFC0000 write-protect
[    0.000000]   1 base 0FFFE0000 mask FFFFE0000 write-protect
[    0.000000]   2 base 000000000 mask F80000000 write-back
[    0.000000]   3 base 080000000 mask FC0000000 write-back
[    0.000000]   4 base 0BFE00000 mask FFFE00000 uncachable
[    0.000000]   5 base 100000000 mask FC0000000 write-back
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] last_pfn = 0xbfe00 max_arch_pfn = 0x400000000
[    0.000000] initial memory mapped : 0 - 20000000
[    0.000000] Base memory trampoline at [ffff880000099000] 99000 size 20480
[    0.000000] init_memory_mapping: 0000000000000000-00000000bfe00000
[    0.000000]  0000000000 - 00bfe00000 page 2M
[    0.000000] kernel direct mapping tables up to bfe00000 @ 1fffc000-20000000
[    0.000000] init_memory_mapping: 0000000100000000-0000000140000000
[    0.000000]  0100000000 - 0140000000 page 2M
[    0.000000] kernel direct mapping tables up to 140000000 @ bfde5000-bfdeb000
[    0.000000] RAMDISK: 37a4a000 - 37d1d000
[    0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 ACRSYS)
[    0.000000] ACPI: XSDT 00000000bfdfe120 0006C (v01 ACRSYS ACRPRDCT 00000001      01000013)
[    0.000000] ACPI: FACP 00000000bfdfc000 000F4 (v04 ACRSYS ACRPRDCT 00000001 1025 01000013)
[    0.000000] ACPI: DSDT 00000000bfdee000 0913C (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
[    0.000000] ACPI: FACS 00000000bfd8f000 00040
[    0.000000] ACPI: DMAR 00000000bfdfd000 000B0 (v01               ? 00000001      00000000)
[    0.000000] ACPI: HPET 00000000bfdfb000 00038 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
[    0.000000] ACPI: APIC 00000000bfdfa000 0006C (v02 ACRSYS ACRPRDCT 00000001 1025 01000013)
[    0.000000] ACPI: MCFG 00000000bfdf9000 0003C (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
[    0.000000] ACPI: ASF! 00000000bfdf8000 000A5 (v32 ACRSYS ACRPRDCT 00000001 1025 01000013)
[    0.000000] ACPI: SLIC 00000000bfded000 00176 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
[    0.000000] ACPI: BOOT 00000000bfdec000 00028 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
[    0.000000] ACPI: SSDT 00000000bfdeb000 00655 (v01  PmRef    CpuPm 00003000 INTL 20051117)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at 0000000000000000-0000000140000000
[    0.000000] Initmem setup node 0 0000000000000000-0000000140000000
[    0.000000]   NODE_DATA [000000013fffc000 - 000000013fffffff]
[    0.000000]  [ffffea0000000000-ffffea0004ffffff] PMD -> [ffff88013b600000-ffff88013f5fffff] on node 0
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   DMA32    0x00001000 -> 0x00100000
[    0.000000]   Normal   0x00100000 -> 0x00140000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009e
[    0.000000]     0: 0x00000100 -> 0x000bfc69
[    0.000000]     0: 0x000bfcbf -> 0x000bfd82
[    0.000000]     0: 0x000bfdbf -> 0x000bfdeb
[    0.000000]     0: 0x000bfdff -> 0x000bfe00
[    0.000000]     0: 0x00100000 -> 0x00140000
[    0.000000] On node 0 totalpages: 1047783
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 5 pages reserved
[    0.000000]   DMA zone: 3913 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 16320 pages used for memmap
[    0.000000]   DMA32 zone: 765337 pages, LIFO batch:31
[    0.000000]   Normal zone: 4096 pages used for memmap
[    0.000000]   Normal zone: 258048 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x00] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x00] disabled)
[    0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[    0.000000] PM: Registered nosave memory: 00000000bfc69000 - 00000000bfcbf000
[    0.000000] PM: Registered nosave memory: 00000000bfd82000 - 00000000bfdbf000
[    0.000000] PM: Registered nosave memory: 00000000bfdeb000 - 00000000bfdff000
[    0.000000] PM: Registered nosave memory: 00000000bfe00000 - 00000000c0000000
[    0.000000] PM: Registered nosave memory: 00000000c0000000 - 00000000f8000000
[    0.000000] PM: Registered nosave memory: 00000000f8000000 - 00000000fc000000
[    0.000000] PM: Registered nosave memory: 00000000fc000000 - 00000000fec00000
[    0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
[    0.000000] PM: Registered nosave memory: 00000000fec01000 - 00000000fed10000
[    0.000000] PM: Registered nosave memory: 00000000fed10000 - 00000000fed14000
[    0.000000] PM: Registered nosave memory: 00000000fed14000 - 00000000fed18000
[    0.000000] PM: Registered nosave memory: 00000000fed18000 - 00000000fed1a000
[    0.000000] PM: Registered nosave memory: 00000000fed1a000 - 00000000fed1c000
[    0.000000] PM: Registered nosave memory: 00000000fed1c000 - 00000000fed20000
[    0.000000] PM: Registered nosave memory: 00000000fed20000 - 00000000fee00000
[    0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[    0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ffe00000
[    0.000000] PM: Registered nosave memory: 00000000ffe00000 - 0000000100000000
[    0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:38000000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] PERCPU: Embedded 28 pages/cpu @ffff88013fc00000 s82880 r8192 d23616 u524288
[    0.000000] pcpu-alloc: s82880 r8192 d23616 u524288 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 1027298
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=2cf171c4-d86a-4d68-894e-d503cec468f1 ro quiet add_efi_memmap
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 4045004k/5242880k available (4538k kernel code, 1051748k absent, 146128k reserved, 4308k data, 740k init)
[    0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] 	Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] NR_IRQS:4352 nr_irqs:712 16
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] allocated 16777216 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] hpet clockevent registered
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 2261.057 MHz processor.
[    0.003337] Calibrating delay loop (skipped), value calculated using timer frequency.. 4523.53 BogoMIPS (lpj=7536856)
[    0.003341] pid_max: default: 32768 minimum: 301
[    0.003370] Security Framework initialized
[    0.003375] AppArmor: AppArmor disabled by boot time parameter
[    0.003708] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.008010] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.008979] Mount-cache hash table entries: 256
[    0.009226] Initializing cgroup subsys cpuacct
[    0.009229] Initializing cgroup subsys memory
[    0.009239] Initializing cgroup subsys devices
[    0.009242] Initializing cgroup subsys freezer
[    0.009244] Initializing cgroup subsys net_cls
[    0.009246] Initializing cgroup subsys blkio
[    0.009280] CPU: Physical Processor ID: 0
[    0.009282] CPU: Processor Core ID: 0
[    0.009284] mce: CPU supports 6 MCE banks
[    0.009292] CPU0: Thermal monitoring enabled (TM1)
[    0.009297] using mwait in idle threads.
[    0.010610] ACPI: Core revision 20120320
[    0.016684] ftrace: allocating 17820 entries in 70 pages
[    0.023402] DMAR: Host address width 36
[    0.023405] DMAR: DRHD base: 0x000000feb00000 flags: 0x0
[    0.023411] IOMMU 0: reg_base_addr feb00000 ver 1:0 cap c9008020e30260 ecap 1000
[    0.023413] DMAR: DRHD base: 0x000000feb03000 flags: 0x1
[    0.023421] IOMMU 1: reg_base_addr feb03000 ver 1:0 cap c90080206f0460 ecap 1000
[    0.023423] DMAR: RMRR base: 0x00000000000000 end: 0x00000000000000
[    0.023942] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.058922] CPU0: Intel(R) Core(TM)2 Duo CPU     P8400  @ 2.26GHz stepping 06
[    0.059996] Performance Events: PEBS fmt0+, 4-deep LBR, Core2 events, Intel PMU driver.
[    0.059996] ... version:                2
[    0.059996] ... bit width:              40
[    0.059996] ... generic registers:      2
[    0.059996] ... value mask:             000000ffffffffff
[    0.059996] ... max period:             000000007fffffff
[    0.059996] ... fixed-purpose events:   3
[    0.059996] ... event mask:             0000000700000003
[    0.076786] NMI watchdog: enabled, takes one hw-pmu counter.
[    0.096677] Booting Node   0, Processors  #1
[    0.109814] NMI watchdog: enabled, takes one hw-pmu counter.
[    0.109865] Brought up 2 CPUs
[    0.109867] Total of 2 processors activated (9047.07 BogoMIPS).
[    0.110077] devtmpfs: initialized
[    0.110094] PM: Registering ACPI NVS region [mem 0xbfd82000-0xbfdbefff] (249856 bytes)
[    0.113983] NET: Registered protocol family 16
[    0.114112] ACPI: bus type pci registered
[    0.114186] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[    0.114189] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[    0.127430] PCI: Using configuration type 1 for base access
[    0.127559] mtrr: your CPUs had inconsistent variable MTRR settings
[    0.127560] mtrr: probably your BIOS does not setup all CPUs.
[    0.127562] mtrr: corrected configuration.
[    0.127937] bio: create slab <bio-0> at 0
[    0.127937] ACPI: Added _OSI(Module Device)
[    0.127937] ACPI: Added _OSI(Processor Device)
[    0.127937] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.127937] ACPI: Added _OSI(Processor Aggregator Device)
[    0.127937] ACPI: EC: Look up EC in DSDT
[    0.128917] ACPI: Executed 1 blocks of module-level executable AML code
[    0.143334] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[    0.153703] ACPI: SSDT 00000000bfc77c18 00265 (v01  PmRef  Cpu0Ist 00003000 INTL 20051117)
[    0.154109] ACPI: Dynamic OEM Table Load:
[    0.154112] ACPI: SSDT           (null) 00265 (v01  PmRef  Cpu0Ist 00003000 INTL 20051117)
[    0.154252] ACPI: SSDT 00000000bfc75598 00537 (v01  PmRef  Cpu0Cst 00003001 INTL 20051117)
[    0.154645] ACPI: Dynamic OEM Table Load:
[    0.154647] ACPI: SSDT           (null) 00537 (v01  PmRef  Cpu0Cst 00003001 INTL 20051117)
[    0.156899] ACPI: SSDT 00000000bfc76e18 001CF (v01  PmRef    ApIst 00003000 INTL 20051117)
[    0.157317] ACPI: Dynamic OEM Table Load:
[    0.157320] ACPI: SSDT           (null) 001CF (v01  PmRef    ApIst 00003000 INTL 20051117)
[    0.157331] ACPI: SSDT 00000000bfc77f18 0008D (v01  PmRef    ApCst 00003000 INTL 20051117)
[    0.157331] ACPI: Dynamic OEM Table Load:
[    0.157331] ACPI: SSDT           (null) 0008D (v01  PmRef    ApCst 00003000 INTL 20051117)
[    0.160035] ACPI: Interpreter enabled
[    0.160039] ACPI: (supports S0 S3 S4 S5)
[    0.160069] ACPI: Using IOAPIC for interrupt routing
[    0.160964] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[    0.164272] ACPI: Power Resource [FN00] (off)
[    0.164984] ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62
[    0.165148] ACPI: No dock devices found.
[    0.165152] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.165406] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.165860] pci_root PNP0A08:00: host bridge window [io  0x0000-0x0cf7]
[    0.165863] pci_root PNP0A08:00: host bridge window [io  0x0d00-0xffff]
[    0.165866] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[    0.165870] pci_root PNP0A08:00: host bridge window [mem 0xc0000000-0xfebfffff]
[    0.165901] PCI host bridge to bus 0000:00
[    0.165903] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.165905] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff]
[    0.165910] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.165912] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xfebfffff]
[    0.165922] pci 0000:00:00.0: [8086:2a40] type 00 class 0x060000
[    0.165942] DMAR: Forcing write-buffer flush capability
[    0.165944] DMAR: Disabling IOMMU for graphics on this chipset
[    0.165969] pci 0000:00:01.0: [8086:2a41] type 01 class 0x060400
[    0.166009] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.166059] pci 0000:00:1a.0: [8086:2937] type 00 class 0x0c0300
[    0.166126] pci 0000:00:1a.0: reg 20: [io  0x70e0-0x70ff]
[    0.166203] pci 0000:00:1a.1: [8086:2938] type 00 class 0x0c0300
[    0.166273] pci 0000:00:1a.1: reg 20: [io  0x70c0-0x70df]
[    0.166371] pci 0000:00:1a.7: [8086:293c] type 00 class 0x0c0320
[    0.167157] pci 0000:00:1a.7: reg 10: [mem 0xdb305c00-0xdb305fff]
[    0.171499] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[    0.171534] pci 0000:00:1b.0: [8086:293e] type 00 class 0x040300
[    0.171552] pci 0000:00:1b.0: reg 10: [mem 0xdb300000-0xdb303fff 64bit]
[    0.171637] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.171664] pci 0000:00:1c.0: [8086:2940] type 01 class 0x060400
[    0.171752] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.171780] pci 0000:00:1c.1: [8086:2942] type 01 class 0x060400
[    0.171874] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.171906] pci 0000:00:1c.3: [8086:2946] type 01 class 0x060400
[    0.171997] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[    0.172026] pci 0000:00:1c.4: [8086:2948] type 01 class 0x060400
[    0.172115] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[    0.172150] pci 0000:00:1d.0: [8086:2934] type 00 class 0x0c0300
[    0.172219] pci 0000:00:1d.0: reg 20: [io  0x70a0-0x70bf]
[    0.172302] pci 0000:00:1d.1: [8086:2935] type 00 class 0x0c0300
[    0.172369] pci 0000:00:1d.1: reg 20: [io  0x7080-0x709f]
[    0.172453] pci 0000:00:1d.2: [8086:2936] type 00 class 0x0c0300
[    0.172526] pci 0000:00:1d.2: reg 20: [io  0x7060-0x707f]
[    0.172609] pci 0000:00:1d.3: [8086:2939] type 00 class 0x0c0300
[    0.172677] pci 0000:00:1d.3: reg 20: [io  0x7040-0x705f]
[    0.172770] pci 0000:00:1d.7: [8086:293a] type 00 class 0x0c0320
[    0.173713] pci 0000:00:1d.7: reg 10: [mem 0xdb305800-0xdb305bff]
[    0.178161] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.178189] pci 0000:00:1e.0: [8086:2448] type 01 class 0x060401
[    0.178268] pci 0000:00:1f.0: [8086:2919] type 00 class 0x060100
[    0.178418] pci 0000:00:1f.2: [8086:2929] type 00 class 0x010601
[    0.178442] pci 0000:00:1f.2: reg 10: [io  0x7108-0x710f]
[    0.178452] pci 0000:00:1f.2: reg 14: [io  0x7114-0x7117]
[    0.178462] pci 0000:00:1f.2: reg 18: [io  0x7100-0x7107]
[    0.178471] pci 0000:00:1f.2: reg 1c: [io  0x7110-0x7113]
[    0.178481] pci 0000:00:1f.2: reg 20: [io  0x7020-0x703f]
[    0.178491] pci 0000:00:1f.2: reg 24: [mem 0xdb305000-0xdb3057ff]
[    0.178549] pci 0000:00:1f.2: PME# supported from D3hot
[    0.178572] pci 0000:00:1f.3: [8086:2930] type 00 class 0x0c0500
[    0.178590] pci 0000:00:1f.3: reg 10: [mem 0xdb306000-0xdb3060ff 64bit]
[    0.178616] pci 0000:00:1f.3: reg 20: [io  0x7000-0x701f]
[    0.178661] pci 0000:00:1f.6: [8086:2932] type 00 class 0x118000
[    0.178691] pci 0000:00:1f.6: reg 10: [mem 0xdb304000-0xdb304fff 64bit]
[    0.178871] pci 0000:01:00.0: [10de:0649] type 00 class 0x030000
[    0.178907] pci 0000:01:00.0: reg 10: [mem 0xd2000000-0xd2ffffff]
[    0.178933] pci 0000:01:00.0: reg 14: [mem 0xc0000000-0xcfffffff 64bit pref]
[    0.178958] pci 0000:01:00.0: reg 1c: [mem 0xd0000000-0xd1ffffff 64bit]
[    0.178977] pci 0000:01:00.0: reg 24: [io  0x6000-0x607f]
[    0.178997] pci 0000:01:00.0: reg 30: [mem 0xfff80000-0xffffffff pref]
[    0.183347] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.183351] pci 0000:00:01.0:   bridge window [io  0x6000-0x6fff]
[    0.183354] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xd2ffffff]
[    0.183358] pci 0000:00:01.0:   bridge window [mem 0xc0000000-0xcfffffff 64bit pref]
[    0.183432] pci 0000:02:00.0: [1969:1026] type 00 class 0x020000
[    0.183463] pci 0000:02:00.0: reg 10: [mem 0xda200000-0xda23ffff 64bit]
[    0.183480] pci 0000:02:00.0: reg 18: [io  0x4000-0x407f]
[    0.183624] pci 0000:02:00.0: PME# supported from D3hot D3cold
[    0.183658] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.183669] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[    0.183674] pci 0000:00:1c.0:   bridge window [io  0x4000-0x5fff]
[    0.183678] pci 0000:00:1c.0:   bridge window [mem 0xda200000-0xdb2fffff]
[    0.183685] pci 0000:00:1c.0:   bridge window [mem 0xd3000000-0xd3ffffff 64bit pref]
[    0.183734] pci 0000:00:1c.1: PCI bridge to [bus 03-04]
[    0.183738] pci 0000:00:1c.1:   bridge window [io  0x3000-0x3fff]
[    0.183743] pci 0000:00:1c.1:   bridge window [mem 0xd9200000-0xda1fffff]
[    0.183749] pci 0000:00:1c.1:   bridge window [mem 0xd4000000-0xd4ffffff 64bit pref]
[    0.183861] pci 0000:05:00.0: [8086:4232] type 00 class 0x028000
[    0.183903] pci 0000:05:00.0: reg 10: [mem 0xd8100000-0xd8101fff 64bit]
[    0.184097] pci 0000:05:00.0: PME# supported from D0 D3hot D3cold
[    0.184196] pci 0000:00:1c.3: PCI bridge to [bus 05-05]
[    0.184200] pci 0000:00:1c.3:   bridge window [io  0x2000-0x2fff]
[    0.184204] pci 0000:00:1c.3:   bridge window [mem 0xd8100000-0xd91fffff]
[    0.184211] pci 0000:00:1c.3:   bridge window [mem 0xd5000000-0xd5ffffff 64bit pref]
[    0.184260] pci 0000:00:1c.4: PCI bridge to [bus 06-06]
[    0.184265] pci 0000:00:1c.4:   bridge window [io  0x1000-0x1fff]
[    0.184269] pci 0000:00:1c.4:   bridge window [mem 0xd7000000-0xd80fffff]
[    0.184276] pci 0000:00:1c.4:   bridge window [mem 0xd6000000-0xd6ffffff 64bit pref]
[    0.184354] pci 0000:00:1e.0: PCI bridge to [bus 07-07] (subtractive decode)
[    0.184366] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.184368] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.184371] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.184373] pci 0000:00:1e.0:   bridge window [mem 0xc0000000-0xfebfffff] (subtractive decode)
[    0.184403] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.184546] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
[    0.184598] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
[    0.184659] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
[    0.184701] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
[    0.184746] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP4._PRT]
[    0.184789] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP5._PRT]
[    0.184840]  pci0000:00: Requesting ACPI _OSC control (0x1d)
[    0.184843]  pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d
[    0.184845] ACPI _OSC control for PCIe not granted, disabling ASPM
[    0.189093] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
[    0.189145] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12)
[    0.189196] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
[    0.189247] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
[    0.189297] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[    0.189348] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 *10 11 12)
[    0.189397] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 *11 12)
[    0.189448] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12)
[    0.189517] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.189517] vgaarb: loaded
[    0.189517] vgaarb: bridge control possible 0000:01:00.0
[    0.189517] PCI: Using ACPI for IRQ routing
[    0.191592] PCI: pci_cache_line_size set to 64 bytes
[    0.191745] reserve RAM buffer: 000000000009e000 - 000000000009ffff 
[    0.191748] reserve RAM buffer: 00000000bfc69000 - 00000000bfffffff 
[    0.191751] reserve RAM buffer: 00000000bfd82000 - 00000000bfffffff 
[    0.191753] reserve RAM buffer: 00000000bfdeb000 - 00000000bfffffff 
[    0.191755] reserve RAM buffer: 00000000bfe00000 - 00000000bfffffff 
[    0.191854] NetLabel: Initializing
[    0.191855] NetLabel:  domain hash size = 128
[    0.191857] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.191870] NetLabel:  unlabeled traffic allowed by default
[    0.191884] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[    0.191890] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[    0.191894] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[    0.210001] Switching to clocksource hpet
[    0.216948] pnp: PnP ACPI init
[    0.216967] ACPI: bus type pnp registered
[    0.217300] pnp 00:00: [bus 00-ff]
[    0.217303] pnp 00:00: [io  0x0000-0x0cf7 window]
[    0.217305] pnp 00:00: [io  0x0cf8-0x0cff]
[    0.217307] pnp 00:00: [io  0x0d00-0xffff window]
[    0.217309] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[    0.217311] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[    0.217313] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[    0.217315] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[    0.217317] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[    0.217319] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[    0.217321] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[    0.217323] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[    0.217325] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[    0.217327] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[    0.217329] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[    0.217331] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[    0.217333] pnp 00:00: [mem 0x000ec000-0x000effff window]
[    0.217335] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[    0.217337] pnp 00:00: [mem 0xc0000000-0xfebfffff window]
[    0.217339] pnp 00:00: [mem 0xfed40000-0xfed44fff window]
[    0.217420] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[    0.217558] pnp 00:01: [io  0x002e-0x002f]
[    0.217560] pnp 00:01: [io  0x004e-0x004f]
[    0.217562] pnp 00:01: [io  0x164e-0x164f]
[    0.217563] pnp 00:01: [io  0x0061]
[    0.217565] pnp 00:01: [io  0x0070]
[    0.217567] pnp 00:01: [io  0x0080]
[    0.217568] pnp 00:01: [io  0x0092]
[    0.217570] pnp 00:01: [io  0x00b2-0x00b3]
[    0.217571] pnp 00:01: [io  0x0063]
[    0.217573] pnp 00:01: [io  0x0065]
[    0.217575] pnp 00:01: [io  0x0067]
[    0.217576] pnp 00:01: [io  0x0600-0x060f]
[    0.217578] pnp 00:01: [io  0x0610]
[    0.217580] pnp 00:01: [io  0x0800-0x080f]
[    0.217582] pnp 00:01: [io  0x0810-0x0817]
[    0.217583] pnp 00:01: [io  0x0820-0x0823]
[    0.217585] pnp 00:01: [io  0x0400-0x047f]
[    0.217587] pnp 00:01: [io  0x0500-0x053f]
[    0.217588] pnp 00:01: [mem 0xf8000000-0xfbffffff]
[    0.217590] pnp 00:01: [mem 0xfed1c000-0xfed1ffff]
[    0.217592] pnp 00:01: [mem 0xfed10000-0xfed13fff]
[    0.217597] pnp 00:01: [mem 0xfed18000-0xfed18fff]
[    0.217599] pnp 00:01: [mem 0xfed19000-0xfed19fff]
[    0.217601] pnp 00:01: [mem 0xfec00000-0xfec00fff]
[    0.217603] pnp 00:01: [mem 0xfed20000-0xfed3ffff]
[    0.217604] pnp 00:01: [mem 0xfed40000-0xfed44fff]
[    0.217606] pnp 00:01: [mem 0xfed45000-0xfed8ffff]
[    0.217608] pnp 00:01: [mem 0xfee00000-0xfee00fff]
[    0.217637] pnp 00:01: disabling [io  0x164e-0x164f] because it overlaps 0000:00:1c.4 BAR 13 [io  0x1000-0x1fff]
[    0.217706] system 00:01: [io  0x0600-0x060f] has been reserved
[    0.217708] system 00:01: [io  0x0610] has been reserved
[    0.217711] system 00:01: [io  0x0800-0x080f] has been reserved
[    0.217713] system 00:01: [io  0x0810-0x0817] has been reserved
[    0.217716] system 00:01: [io  0x0820-0x0823] has been reserved
[    0.217718] system 00:01: [io  0x0400-0x047f] has been reserved
[    0.217720] system 00:01: [io  0x0500-0x053f] has been reserved
[    0.217724] system 00:01: [mem 0xf8000000-0xfbffffff] has been reserved
[    0.217727] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.217729] system 00:01: [mem 0xfed10000-0xfed13fff] has been reserved
[    0.217732] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.217734] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.217737] system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.217739] system 00:01: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.217742] system 00:01: [mem 0xfed40000-0xfed44fff] has been reserved
[    0.217744] system 00:01: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.217747] system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.217751] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.217760] pnp 00:02: [io  0x0000-0x001f]
[    0.217762] pnp 00:02: [io  0x0081-0x0091]
[    0.217764] pnp 00:02: [io  0x0093-0x009f]
[    0.217765] pnp 00:02: [io  0x00c0-0x00df]
[    0.217768] pnp 00:02: [dma 4]
[    0.217800] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.217822] pnp 00:03: [io  0x0070-0x0077]
[    0.217853] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.217907] pnp 00:04: [irq 0 disabled]
[    0.217920] pnp 00:04: [irq 8]
[    0.217921] pnp 00:04: [mem 0xfed00000-0xfed003ff]
[    0.217956] pnp 00:04: Plug and Play ACPI device, IDs PNP0103 (active)
[    0.217966] pnp 00:05: [io  0x00f0]
[    0.217972] pnp 00:05: [irq 13]
[    0.218003] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.218012] pnp 00:06: [mem 0xff800000-0xffffffff]
[    0.218046] pnp 00:06: Plug and Play ACPI device, IDs INT0800 (active)
[    0.218061] pnp 00:07: [io  0x0060]
[    0.218063] pnp 00:07: [io  0x0064]
[    0.218069] pnp 00:07: [irq 1]
[    0.218100] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.218112] pnp 00:08: [irq 12]
[    0.218149] pnp 00:08: Plug and Play ACPI device, IDs SYN1b19 SYN1b00 SYN0002 PNP0f13 (active)
[    0.218197] pnp 00:09: [io  0x0310-0x0317]
[    0.218202] pnp 00:09: [irq 6]
[    0.218236] pnp 00:09: Plug and Play ACPI device, IDs ITE8708 (active)
[    0.218322] pnp: PnP ACPI: found 10 devices
[    0.218324] ACPI: ACPI bus type pnp unregistered
[    0.225251] pci 0000:01:00.0: no compatible bridge window for [mem 0xfff80000-0xffffffff pref]
[    0.225313] pci 0000:01:00.0: BAR 6: can't assign mem pref (size 0x80000)
[    0.225317] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.225320] pci 0000:00:01.0:   bridge window [io  0x6000-0x6fff]
[    0.225324] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xd2ffffff]
[    0.225328] pci 0000:00:01.0:   bridge window [mem 0xc0000000-0xcfffffff 64bit pref]
[    0.225333] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[    0.225336] pci 0000:00:1c.0:   bridge window [io  0x4000-0x5fff]
[    0.225342] pci 0000:00:1c.0:   bridge window [mem 0xda200000-0xdb2fffff]
[    0.225347] pci 0000:00:1c.0:   bridge window [mem 0xd3000000-0xd3ffffff 64bit pref]
[    0.225354] pci 0000:00:1c.1: PCI bridge to [bus 03-04]
[    0.225357] pci 0000:00:1c.1:   bridge window [io  0x3000-0x3fff]
[    0.225363] pci 0000:00:1c.1:   bridge window [mem 0xd9200000-0xda1fffff]
[    0.225368] pci 0000:00:1c.1:   bridge window [mem 0xd4000000-0xd4ffffff 64bit pref]
[    0.225375] pci 0000:00:1c.3: PCI bridge to [bus 05-05]
[    0.225378] pci 0000:00:1c.3:   bridge window [io  0x2000-0x2fff]
[    0.225384] pci 0000:00:1c.3:   bridge window [mem 0xd8100000-0xd91fffff]
[    0.225389] pci 0000:00:1c.3:   bridge window [mem 0xd5000000-0xd5ffffff 64bit pref]
[    0.225396] pci 0000:00:1c.4: PCI bridge to [bus 06-06]
[    0.225399] pci 0000:00:1c.4:   bridge window [io  0x1000-0x1fff]
[    0.225405] pci 0000:00:1c.4:   bridge window [mem 0xd7000000-0xd80fffff]
[    0.225410] pci 0000:00:1c.4:   bridge window [mem 0xd6000000-0xd6ffffff 64bit pref]
[    0.225417] pci 0000:00:1e.0: PCI bridge to [bus 07-07]
[    0.225456] pci 0000:00:1c.1: enabling device (0000 -> 0003)
[    0.225478] pci 0000:00:1e.0: setting latency timer to 64
[    0.225483] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.225485] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.225487] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.225489] pci_bus 0000:00: resource 7 [mem 0xc0000000-0xfebfffff]
[    0.225492] pci_bus 0000:01: resource 0 [io  0x6000-0x6fff]
[    0.225494] pci_bus 0000:01: resource 1 [mem 0xd0000000-0xd2ffffff]
[    0.225496] pci_bus 0000:01: resource 2 [mem 0xc0000000-0xcfffffff 64bit pref]
[    0.225499] pci_bus 0000:02: resource 0 [io  0x4000-0x5fff]
[    0.225501] pci_bus 0000:02: resource 1 [mem 0xda200000-0xdb2fffff]
[    0.225503] pci_bus 0000:02: resource 2 [mem 0xd3000000-0xd3ffffff 64bit pref]
[    0.225506] pci_bus 0000:03: resource 0 [io  0x3000-0x3fff]
[    0.225508] pci_bus 0000:03: resource 1 [mem 0xd9200000-0xda1fffff]
[    0.225510] pci_bus 0000:03: resource 2 [mem 0xd4000000-0xd4ffffff 64bit pref]
[    0.225512] pci_bus 0000:05: resource 0 [io  0x2000-0x2fff]
[    0.225514] pci_bus 0000:05: resource 1 [mem 0xd8100000-0xd91fffff]
[    0.225517] pci_bus 0000:05: resource 2 [mem 0xd5000000-0xd5ffffff 64bit pref]
[    0.225519] pci_bus 0000:06: resource 0 [io  0x1000-0x1fff]
[    0.225521] pci_bus 0000:06: resource 1 [mem 0xd7000000-0xd80fffff]
[    0.225523] pci_bus 0000:06: resource 2 [mem 0xd6000000-0xd6ffffff 64bit pref]
[    0.225526] pci_bus 0000:07: resource 4 [io  0x0000-0x0cf7]
[    0.225528] pci_bus 0000:07: resource 5 [io  0x0d00-0xffff]
[    0.225530] pci_bus 0000:07: resource 6 [mem 0x000a0000-0x000bffff]
[    0.225532] pci_bus 0000:07: resource 7 [mem 0xc0000000-0xfebfffff]
[    0.225577] NET: Registered protocol family 2
[    0.225710] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.226699] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[    0.230444] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.230929] TCP: Hash tables configured (established 524288 bind 65536)
[    0.230931] TCP: reno registered
[    0.230941] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.230978] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.231109] NET: Registered protocol family 1
[    0.256751] pci 0000:01:00.0: Boot video device
[    0.256789] PCI: CLS 64 bytes, default 64
[    0.256842] Unpacking initramfs...
[    0.318354] Freeing initrd memory: 2892k freed
[    0.319318] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.319321] Placing 64MB software IO TLB between ffff8800bbc69000 - ffff8800bfc69000
[    0.319324] software IO TLB at phys 0xbbc69000 - 0xbfc69000
[    0.319349] Simple Boot Flag value 0x5 read from CMOS RAM was invalid
[    0.319351] Simple Boot Flag at 0x44 set to 0x1
[    0.319837] audit: initializing netlink socket (disabled)
[    0.319852] type=2000 audit(1341402531.316:1): initialized
[    0.320397] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.322524] VFS: Disk quotas dquot_6.5.2
[    0.322571] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.322673] msgmni has been set to 7906
[    0.322867] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.322901] io scheduler noop registered
[    0.322903] io scheduler deadline registered
[    0.322956] io scheduler cfq registered (default)
[    0.323083] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[    0.323182] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[    0.323305] pcieport 0000:00:1c.1: irq 42 for MSI/MSI-X
[    0.323456] pcieport 0000:00:1c.3: irq 43 for MSI/MSI-X
[    0.323583] pcieport 0000:00:1c.4: irq 44 for MSI/MSI-X
[    0.323729] vesafb: mode is 1280x1024x32, linelength=5120, pages=0
[    0.323732] vesafb: scrolling: redraw
[    0.323734] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    0.324991] vesafb: framebuffer at 0xd1000000, mapped to 0xffffc90005100000, using 5120k, total 5120k
[    0.385388] Console: switching to colour frame buffer device 160x64
[    0.445542] fb0: VESA VGA frame buffer device
[    0.445553] intel_idle: does not run on family 6 model 23
[    0.445602] GHES: HEST is not enabled!
[    0.445668] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.446104] Linux agpgart interface v0.103
[    0.446175] i8042: PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOUE] at 0x60,0x64 irq 1,12
[    0.449763] i8042: Detected active multiplexing controller, rev 1.1
[    0.451174] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.451208] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    0.451233] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    0.451256] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    0.451281] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    0.451388] mousedev: PS/2 mouse device common for all mice
[    0.451459] rtc_cmos 00:03: RTC can wake from S4
[    0.451595] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    0.451624] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[    0.451633] cpuidle: using governor ladder
[    0.451634] cpuidle: using governor menu
[    0.451768] TCP: cubic registered
[    0.451873] NET: Registered protocol family 10
[    0.452064] NET: Registered protocol family 17
[    0.452068] Registering the dns_resolver key type
[    0.452203] PM: Hibernation image not present or could not be loaded.
[    0.452210] registered taskstats version 1
[    0.452925] rtc_cmos 00:03: setting system clock to 2012-07-04 11:48:52 UTC (1341402532)
[    0.452983] Initializing network drop monitor service
[    0.454579] Freeing unused kernel memory: 740k freed
[    0.454787] Write protecting the kernel read-only data: 8192k
[    0.459598] Freeing unused kernel memory: 1588k freed
[    0.461962] Freeing unused kernel memory: 640k freed
[    0.469490] udevd[41]: starting version 185
[    0.490202] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    0.504006] usbcore: registered new interface driver usbfs
[    0.504034] usbcore: registered new interface driver hub
[    0.504994] usbcore: registered new device driver usb
[    0.505577] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.505631] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[    0.505635] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[    0.505658] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[    0.505691] ehci_hcd 0000:00:1a.7: debug port 1
[    0.509570] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
[    0.509598] ehci_hcd 0000:00:1a.7: irq 19, io mem 0xdb305c00
[    0.510751] SCSI subsystem initialized
[    0.512443] libata version 3.00 loaded.
[    0.513645] uhci_hcd: USB Universal Host Controller Interface driver
[    0.516688] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[    0.516872] hub 1-0:1.0: USB hub found
[    0.516877] hub 1-0:1.0: 4 ports detected
[    0.517006] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    0.517010] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    0.517019] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[    0.517048] ehci_hcd 0000:00:1d.7: debug port 1
[    0.520920] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[    0.520938] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xdb305800
[    0.530133] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    0.530334] hub 2-0:1.0: USB hub found
[    0.530339] hub 2-0:1.0: 8 ports detected
[    0.530720] ahci 0000:00:1f.2: version 3.0
[    0.530789] ahci 0000:00:1f.2: irq 45 for MSI/MSI-X
[    0.530872] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x33 impl SATA mode
[    0.530876] ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc ems sxs 
[    0.530882] ahci 0000:00:1f.2: setting latency timer to 64
[    0.550648] scsi0 : ahci
[    0.550743] scsi1 : ahci
[    0.550823] scsi2 : ahci
[    0.550897] scsi3 : ahci
[    0.550973] scsi4 : ahci
[    0.551046] scsi5 : ahci
[    0.551180] ata1: SATA max UDMA/133 abar m2048@0xdb305000 port 0xdb305100 irq 45
[    0.551183] ata2: SATA max UDMA/133 abar m2048@0xdb305000 port 0xdb305180 irq 45
[    0.551185] ata3: DUMMY
[    0.551187] ata4: DUMMY
[    0.551189] ata5: SATA max UDMA/133 abar m2048@0xdb305000 port 0xdb305300 irq 45
[    0.551193] ata6: SATA max UDMA/133 abar m2048@0xdb305000 port 0xdb305380 irq 45
[    0.551247] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[    0.551251] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[    0.551266] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[    0.551306] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000070e0
[    0.551464] hub 3-0:1.0: USB hub found
[    0.551468] hub 3-0:1.0: 2 ports detected
[    0.551557] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[    0.551561] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[    0.551571] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[    0.551613] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000070c0
[    0.551755] hub 4-0:1.0: USB hub found
[    0.551759] hub 4-0:1.0: 2 ports detected
[    0.551840] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    0.551844] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    0.551852] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[    0.551879] uhci_hcd 0000:00:1d.0: irq 23, io base 0x000070a0
[    0.552036] hub 5-0:1.0: USB hub found
[    0.552040] hub 5-0:1.0: 2 ports detected
[    0.552119] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    0.552123] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    0.552130] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[    0.552159] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00007080
[    0.552296] hub 6-0:1.0: USB hub found
[    0.552300] hub 6-0:1.0: 2 ports detected
[    0.552380] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    0.552383] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    0.552391] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[    0.552418] uhci_hcd 0000:00:1d.2: irq 16, io base 0x00007060
[    0.552554] hub 7-0:1.0: USB hub found
[    0.552558] hub 7-0:1.0: 2 ports detected
[    0.552636] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    0.552640] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    0.552648] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 8
[    0.552684] uhci_hcd 0000:00:1d.3: irq 18, io base 0x00007040
[    0.552808] hub 8-0:1.0: USB hub found
[    0.552811] hub 8-0:1.0: 2 ports detected
[    0.870075] ata6: SATA link down (SStatus 0 SControl 300)
[    0.870106] ata5: SATA link down (SStatus 0 SControl 300)
[    1.036699] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.036725] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.038977] ata2.00: ATAPI: Slimtype BD  E  DS4E1S, EA12, max UDMA/100
[    1.040251] ata2.00: configured for UDMA/100
[    1.065379] ata1.00: ATA-8: WDC WD3200BEKT-22F3T0, 11.01A11, max UDMA/133
[    1.065382] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[    1.068097] ata1.00: configured for UDMA/133
[    1.068217] scsi 0:0:0:0: Direct-Access     ATA      WDC WD3200BEKT-2 11.0 PQ: 0 ANSI: 5
[    1.071394] scsi 1:0:0:0: CD-ROM            Slimtype BD  E  DS4E1S    EA12 PQ: 0 ANSI: 5
[    1.076154] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[    1.076201] sd 0:0:0:0: [sda] Write Protect is off
[    1.076204] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.076225] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.080468] sr0: scsi3-mmc drive: 24x/1x writer dvd-ram cd/rw xa/form2 cdda pop-up
[    1.080471] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.080588] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.115470]  sda: sda1 sda2 < sda5 sda6 > sda3 sda4
[    1.115891] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.143359] usb 2-6: new high-speed USB device number 5 using ehci_hcd
[    1.320023] Refined TSC clocksource calibration: 2260.999 MHz.
[    1.320028] Switching to clocksource tsc
[    1.570011] usb 5-1: new low-speed USB device number 2 using uhci_hcd
[    1.718565] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
[    1.970014] usb 5-2: new full-speed USB device number 3 using uhci_hcd
[    2.376678] usb 4-2: new full-speed USB device number 2 using uhci_hcd
[    2.753346] usb 6-2: new low-speed USB device number 2 using uhci_hcd
[    3.125047] systemd-vconsole-setup[146]: /usr/bin/setfont failed with error code 64.
[    3.356254] udevd[153]: starting version 185
[    3.638516] fuse init (API version 7.18)
[    3.974507] wmi: Mapper loaded
[    4.006267] microcode: CPU0 sig=0x10676, pf=0x80, revision=0x60c
[    4.078776] ACPI: Fan [FAN0] (off)
[    4.080657] thermal LNXTHERM:00: registered as thermal_zone0
[    4.080659] ACPI: Thermal Zone [TZ00] (34 C)
[    4.080754] [Firmware Bug]: ACPI(EVGA) defines _DOD but not _DOS
[    4.081411] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1
[    4.081418] ACPI: Sleep Button [SLPB]
[    4.081812] ACPI: Battery Slot [BAT0] (battery absent)
[    4.081891] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
[    4.081896] ACPI: Power Button [PWRB]
[    4.081950] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input3
[    4.081981] ACPI: Lid Switch [LID0]
[    4.082049] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[    4.082053] ACPI: Power Button [PWRF]
[    4.082165] thermal LNXTHERM:01: registered as thermal_zone1
[    4.082167] ACPI: Thermal Zone [TZVR] (36 C)
[    4.082773] ACPI: AC Adapter [ADP0] (on-line)
[    4.082995] thermal LNXTHERM:02: registered as thermal_zone2
[    4.082997] ACPI: Thermal Zone [TZVL] (36 C)
[    4.083092] thermal LNXTHERM:03: registered as thermal_zone3
[    4.083094] ACPI: Thermal Zone [TZ01] (28 C)
[    4.090918] ACPI: Requesting acpi_cpufreq
[    4.093406] Monitor-Mwait will be used to enter C-1 state
[    4.093438] Monitor-Mwait will be used to enter C-2 state
[    4.093458] Monitor-Mwait will be used to enter C-3 state
[    4.093464] Marking TSC unstable due to TSC halts in idle
[    4.093481] ACPI: acpi_idle registered with cpuidle
[    4.093694] Switching to clocksource hpet
[    4.100177] ACPI Warning: _BQC returned an invalid level (20120320/video-472)
[    4.156642] input: PC Speaker as /devices/platform/pcspkr/input/input5
[    4.190149] acpi device:03: registered as cooling_device3
[    4.190348] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input6
[    4.190385] ACPI: Video Device [EVGA] (multi-head: yes  rom: no  post: no)
[    4.190406] [Firmware Bug]: Duplicate ACPI video bus devices for the same VGA controller, please try module parameter "video.allow_duplicates=1"if the current driver doesn't work.
[    4.191185] acer_wmi: Acer Laptop ACPI-WMI Extras
[    4.191405] acer_wmi: Function bitmap for Communication Device: 0x17
[    4.191408] acer_wmi: Brightness must be controlled by acpi video driver
[    4.283614] ite_cir: Auto-detected model: ITE8708 CIR transceiver
[    4.283617] ite_cir: Using model: ITE8708 CIR transceiver
[    4.283619] ite_cir: TX-capable: 1
[    4.283621] ite_cir: Sample period (ns): 8680
[    4.283622] ite_cir: TX carrier frequency (Hz): 38000
[    4.283624] ite_cir: TX duty cycle (%): 33
[    4.283625] ite_cir: RX low carrier frequency (Hz): 0
[    4.283627] ite_cir: RX high carrier frequency (Hz): 0
[    4.310896] microcode: CPU1 sig=0x10676, pf=0x80, revision=0x60c
[    4.311341] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    4.316730] Registered IR keymap rc-rc6-mce
[    4.316894] input: ITE8708 CIR transceiver as /devices/virtual/rc/rc0/input7
[    4.317018] rc0: ITE8708 CIR transceiver as /devices/virtual/rc/rc0
[    4.317734] ite_cir: driver has been successfully loaded
[    4.397616] iTCO_vendor_support: vendor-support=0
[    4.402037] Linux media interface: v0.10
[    4.509627] IR NEC protocol handler initialized
[    4.535560] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[    4.535722] iTCO_wdt: Found a ICH9M TCO device (Version=2, TCOBASE=0x0460)
[    4.535862] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    4.602419] input: Microsoft Wired Keyboard 600 as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.0/input/input8
[    4.602529] generic-usb 0003:045E:0750.0001: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Wired Keyboard 600] on usb-0000:00:1d.0-1/input0
[    4.604027] cfg80211: Calling CRDA to update world regulatory domain
[    4.633087] input: Microsoft Wired Keyboard 600 as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.1/input/input9
[    4.633474] generic-usb 0003:045E:0750.0002: input,hidraw1: USB HID v1.11 Device [Microsoft Wired Keyboard 600] on usb-0000:00:1d.0-1/input1
[    4.636175] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input10
[    4.636363] generic-usb 0003:046D:C51A.0003: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-2/input0
[    4.641047] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input11
[    4.641188] generic-usb 0003:046D:C51A.0004: input,hiddev0,hidraw3: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.0-2/input1
[    4.654691] input: PS/2+USB Mouse as /devices/pci0000:00/0000:00:1d.1/usb6/6-2/6-2:1.0/input/input12
[    4.655025] generic-usb 0003:04F3:0212.0005: input,hidraw4: USB HID v1.11 Mouse [PS/2+USB Mouse] on usb-0000:00:1d.1-2/input0
[    4.655087] usbcore: registered new interface driver usbhid
[    4.655090] usbhid: USB HID core driver
[    4.660356] IR RC5(x) protocol handler initialized
[    4.664681] IR RC6 protocol handler initialized
[    4.682897] snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
[    4.736813] psmouse serio2: synaptics: Touchpad model: 1, fw: 6.3, id: 0x12a0b1, caps: 0xa04711/0xa04000/0x0
[    4.775308] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input13
[    4.797063] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input14
[    4.798791] Linux video capture interface: v2.00
[    4.803231] IR JVC protocol handler initialized
[    4.816214] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input15
[    4.816338] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input16
[    4.816415] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input17
[    4.845611] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree:
[    4.845614] Copyright(c) 2003-2012 Intel Corporation
[    4.845773] iwlwifi 0000:05:00.0: pci_resource_len = 0x00002000
[    4.845776] iwlwifi 0000:05:00.0: pci_resource_base = ffffc900050dc000
[    4.845778] iwlwifi 0000:05:00.0: HW Revision ID = 0x0
[    4.845921] iwlwifi 0000:05:00.0: irq 47 for MSI/MSI-X
[    4.852513] uvcvideo: Found UVC 1.00 device Acer HD Crystal Eye webcam (064e:a117)
[    4.861949] input: Acer HD Crystal Eye webcam as /devices/pci0000:00/0000:00:1d.7/usb2/2-6/2-6:1.0/input/input18
[    4.862054] usbcore: registered new interface driver uvcvideo
[    4.862057] USB Video Class driver (1.1.1)
[    5.008907] IR Sony protocol handler initialized
[    5.077571] IR SANYO protocol handler initialized
[    5.147667] iwlwifi 0000:05:00.0: loaded firmware version 8.83.5.1 build 33692
[    5.147930] iwlwifi 0000:05:00.0: CONFIG_IWLWIFI_DEBUG disabled
[    5.147932] iwlwifi 0000:05:00.0: CONFIG_IWLWIFI_DEBUGFS disabled
[    5.147934] iwlwifi 0000:05:00.0: CONFIG_IWLWIFI_DEVICE_TRACING enabled
[    5.147936] iwlwifi 0000:05:00.0: CONFIG_IWLWIFI_DEVICE_TESTMODE enabled
[    5.147938] iwlwifi 0000:05:00.0: CONFIG_IWLWIFI_P2P disabled
[    5.147942] iwlwifi 0000:05:00.0: Detected Intel(R) WiFi Link 5100 AGN, REV=0x54
[    5.148055] iwlwifi 0000:05:00.0: L1 Enabled; Disabling L0S
[    5.167580] input: MCE IR Keyboard/Mouse (ite-cir) as /devices/virtual/input/input19
[    5.167665] IR MCE Keyboard/mouse protocol handler initialized
[    5.169880] iwlwifi 0000:05:00.0: device EEPROM VER=0x11f, CALIB=0x4
[    5.169883] iwlwifi 0000:05:00.0: Device SKU: 0xF0
[    5.169886] iwlwifi 0000:05:00.0: Valid Tx ant: 0x2, Valid Rx ant: 0x3
[    5.169900] iwlwifi 0000:05:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels
[    5.169961] Registered led device: phy0-led
[    5.198842] lirc_dev: IR Remote Control driver registered, major 250 
[    5.199113] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs'
[    5.200250] rc rc0: lirc_dev: driver ir-lirc-codec (ite-cir) registered at minor = 0
[    5.200252] IR LIRC bridge handler initialized
[    5.236794] nvidia: module license 'NVIDIA' taints kernel.
[    5.236798] Disabling lock debugging due to kernel taint
[    5.252851] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[    5.253021] NVRM: loading NVIDIA UNIX x86_64 Kernel Module  302.17  Tue Jun 12 16:03:22 PDT 2012
[    6.330450] EXT4-fs (sda4): re-mounted. Opts: (null)
[    6.365118] Adding 2122748k swap on /dev/sda6.  Priority:-1 extents:1 across:2122748k 

Offline

#13 2012-07-06 22:37:24

nomorewindows
Member
Registered: 2010-04-03
Posts: 3,362

Re: GDM and Gnome not working, showing only the cursor and wallpaper

nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
NVRM: loading NVIDIA UNIX x86_64 Kernel Module  302.17  Tue Jun 12 16:03:22 PDT 2012

Are you using nvidia from the repos?
Can you get a framerate?  I usually use stellarium, because it is affected by hardware acceleration settings.  If you are only getting ~5FPS, there isn't any acceleration, but if you're getting ~20 or better, hardware acceleration is working.  glxgears doesn't give a reliable reading.  If worse comes to worse, make sure your user is in the video group.  This seemed to make a difference for everything else besides gnome (even kde).  I still haven't really figured out what has gone weird in gnome.


I may have to CONSOLE you about your usage of ridiculously easy graphical interfaces...
Look ma, no mouse.

Offline

#14 2012-07-07 08:55:37

Strike0
Member
From: Germany
Registered: 2011-09-05
Posts: 1,429

Re: GDM and Gnome not working, showing only the cursor and wallpaper

The nvidia lines look like mine (except the 64 bit). It works here, the module.

I sometimes get that error as well - and when it happens, it only seems to happen after a cold boot.
To quick fix I switch to a TTY, log  into the console, go to runlevel init 1 and back up. then Gnome is always fixed.
You may want to try that.

One thought I have about the reason of it happening is ntpd trying to sync time after a cold boot and finding a bigger time deviation. That's because in such cases I always see a time sync deviation in the terminal before logging in, but I still have to look into the issue.

Offline

#15 2012-07-21 17:24:51

drtechie
Member
Registered: 2012-02-29
Posts: 5

Re: GDM and Gnome not working, showing only the cursor and wallpaper

I am having the same problem. It happened about a week back, after an update and since then I am trying to fix it. After logging in the cursor and wallpaper shows but gnome-shell does not load.
I tried the following...

1.
a) I reverted back from catalyst 12.6 to 12.4
b) Installed lts kernel

That didn't change anything

2. I reset gnome with following

rm -rf .gnome .gnome2 .gconf .gconfd .metacity .cache .dbus .dmrc .mission-control .thumbnails

3. I removed following folders

~/.local/share/gnome-shell
~/.themes

and reinstalled gnome

4. Removed and reinstalled gnome and gnome extra

My Graphics card is ATI Mobility Radeon  HD4570
I am using [catalyst-hd234k-12.4] repository (earlier [catalyst-hd234k])

Here is my .xsession-errors

/etc/gdm/s.png is 1366x768 PNG image, color type RGB, 8 bit
  Zooming image by 100%...done
  Merging...didn't find evidence of prior run.
done
  Building XImage...done
/etc/gdm/Xsession: Beginning session setup...
/etc/gdm/Xsession: Setup done, will execute: /usr/bin/ssh-agent -- gnome-session
gnome-session[1374]: EggSMClient-WARNING: Desktop file '/home/drtechie/.config/autostart/dropbox.desktop' has malformed Icon key 'dropbox.png'(should not include extension)
GNOME_KEYRING_CONTROL=/home/drtechie/.cache/keyring-zo8uVh
GPG_AGENT_INFO=/home/drtechie/.cache/keyring-zo8uVh/gpg:0:1
GNOME_KEYRING_CONTROL=/home/drtechie/.cache/keyring-zo8uVh
GPG_AGENT_INFO=/home/drtechie/.cache/keyring-zo8uVh/gpg:0:1
GNOME_KEYRING_CONTROL=/home/drtechie/.cache/keyring-zo8uVh
GPG_AGENT_INFO=/home/drtechie/.cache/keyring-zo8uVh/gpg:0:1
GNOME_KEYRING_CONTROL=/home/drtechie/.cache/keyring-zo8uVh
GPG_AGENT_INFO=/home/drtechie/.cache/keyring-zo8uVh/gpg:0:1
SSH_AUTH_SOCK=/home/drtechie/.cache/keyring-zo8uVh/ssh

(gnome-settings-daemon:1409): libupower-glib-WARNING **: Couldn't enumerate devices: Message did not receive a reply (timeout by message bus)

(gnome-settings-daemon:1409): power-plugin-WARNING **: failed to get device list: Message did not receive a reply (timeout by message bus)

(gnome-settings-daemon:1409): print-notifications-plugin-WARNING **: Unable to start print-notifications manager: Could not connect: No such file or directory

** (gnome-settings-daemon:1409): WARNING **: cannot connect to ConsoleKit: Could not connect: No such file or directory

(gnome-settings-daemon:1409): color-plugin-WARNING **: failed to connect to colord: Could not connect: No such file or directory

** (gnome-settings-daemon:1409): WARNING **: cannot connect to ConsoleKit: Could not connect: No such file or directory

(gnome-settings-daemon:1409): power-plugin-WARNING **: Could not connect to UPower: Could not connect: No such file or directory

(gnome-settings-daemon:1409): power-plugin-WARNING **: Could not connect to UPower: Could not connect: No such file or directory

(gnome-settings-daemon:1409): media-keys-plugin-WARNING **: Failed to get proxy for upower: Could not connect: No such file or directory
gnome-session[1374]: WARNING: Failed to start app: Unable to start application: Failed to execute child process "unset" (No such file or directory)
Initializing tracker-store...
Tracker-Message: Setting up monitor for changes to config file:'/home/drtechie/.config/tracker/tracker-store.cfg'
Initializing tracker-miner-fs...
Tracker-Message: Setting up monitor for changes to config file:'/home/drtechie/.config/tracker/tracker-store.cfg'
Starting log:
  File:'/home/drtechie/.local/share/tracker/tracker-store.log'
Tracker-Message: Setting up monitor for changes to config file:'/home/drtechie/.config/tracker/tracker-miner-fs.cfg'
Starting log:
  File:'/home/drtechie/.local/share/tracker/tracker-miner-fs.log'

** (nm-applet:1457): WARNING **: Could not initialize NMClient /org/freedesktop/NetworkManager: Launch helper exited with unknown return code 1
** Message: applet now removed from the notification area

** (nm-applet:1457): WARNING **: fetch_connections_done: error fetching connections: (25) Launch helper exited with unknown return code 1.

** (nm-applet:1457): WARNING **: Failed to register as an agent: (25) Launch helper exited with unknown return code 1

(tracker-miner-fs:1456): GVFS-RemoteVolumeMonitor-WARNING **: remote volume monitor with dbus name org.gtk.Private.UDisks2VolumeMonitor is not supported

(gnome-shell:1449): GVFS-RemoteVolumeMonitor-WARNING **: remote volume monitor with dbus name org.gtk.Private.UDisks2VolumeMonitor is not supported
    JS ERROR: !!!   Exception was: Error: Error invoking Gio.bus_get_sync: Could not connect: No such file or directory
    JS ERROR: !!!     lineNumber = '0'
    JS ERROR: !!!     fileName = '"gjs_throw"'
    JS ERROR: !!!     stack = '"("Error invoking Gio.bus_get_sync: Could not connect: No such file or directory")@gjs_throw:0
()@/usr/share/gjs-1.0/overrides/Gio.js:341
ConsoleKitManager()@/usr/share/gnome-shell/js/ui/automountManager.js:40
()@/usr/share/gnome-shell/js/ui/automountManager.js:84
wrapper()@/usr/share/gjs-1.0/lang.js:204
()@/usr/share/gjs-1.0/lang.js:145
()@/usr/share/gjs-1.0/lang.js:239
_createUserSession()@/usr/share/gnome-shell/js/ui/main.js:86
start()@/usr/share/gnome-shell/js/ui/main.js:226
@<main>:1
"'
    JS ERROR: !!!     message = '"Error invoking Gio.bus_get_sync: Could not connect: No such file or directory"'
Window manager warning: Log level 32: Execution of main.js threw exception: Error: Error invoking Gio.bus_get_sync: Could not connect: No such file or directory
** Message: Starting applet secret agent because GNOME Shell disappeared

** (nm-applet:1457): WARNING **: Failed to register as an agent: (25) Launch helper exited with unknown return code 1

My dmesg.log

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.0.36-2-lts (nobody@rampage) (gcc version 4.7.1 (GCC) ) #1 SMP PREEMPT Tue Jul 3 15:04:30 UTC 2012
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-linux-lts root=UUID=59eeed7d-54a3-45b8-8b17-2db45884a6b2 ro quiet nomodeset
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009c400 (usable)
[    0.000000]  BIOS-e820: 000000000009c400 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000bdaa1000 (usable)
[    0.000000]  BIOS-e820: 00000000bdaa1000 - 00000000bdaa7000 (reserved)
[    0.000000]  BIOS-e820: 00000000bdaa7000 - 00000000bdbba000 (usable)
[    0.000000]  BIOS-e820: 00000000bdbba000 - 00000000bdc0f000 (reserved)
[    0.000000]  BIOS-e820: 00000000bdc0f000 - 00000000bdd08000 (usable)
[    0.000000]  BIOS-e820: 00000000bdd08000 - 00000000bdf0f000 (reserved)
[    0.000000]  BIOS-e820: 00000000bdf0f000 - 00000000bdf18000 (usable)
[    0.000000]  BIOS-e820: 00000000bdf18000 - 00000000bdf1f000 (reserved)
[    0.000000]  BIOS-e820: 00000000bdf1f000 - 00000000bdf63000 (usable)
[    0.000000]  BIOS-e820: 00000000bdf63000 - 00000000bdf9f000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000bdf9f000 - 00000000bdfe3000 (usable)
[    0.000000]  BIOS-e820: 00000000bdfe3000 - 00000000bdfff000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000bdfff000 - 00000000be000000 (usable)
[    0.000000]  BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] DMI present.
[    0.000000] DMI: Dell Inc. Studio 1555/0C234M, BIOS A13 04/02/2011
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] No AGP bridge found
[    0.000000] last_pfn = 0x140000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 080000000 mask FC0000000 write-back
[    0.000000]   2 base 100000000 mask FC0000000 write-back
[    0.000000]   3 base 0FFE00000 mask FFFE00000 write-protect
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] last_pfn = 0xbe000 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [ffff8800000f7900] f7900
[    0.000000] initial memory mapped : 0 - 20000000
[    0.000000] Base memory trampoline at [ffff880000097000] 97000 size 20480
[    0.000000] init_memory_mapping: 0000000000000000-00000000be000000
[    0.000000]  0000000000 - 00be000000 page 2M
[    0.000000] kernel direct mapping tables up to be000000 @ 1fffc000-20000000
[    0.000000] init_memory_mapping: 0000000100000000-0000000140000000
[    0.000000]  0100000000 - 0140000000 page 2M
[    0.000000] kernel direct mapping tables up to 140000000 @ bdfdd000-bdfe3000
[    0.000000] RAMDISK: 37b00000 - 37d78000
[    0.000000] ACPI: RSDP 00000000000f7850 00024 (v02 PTLTD )
[    0.000000] ACPI: XSDT 00000000bdff786c 00074 (v01 DELL    QA09    06040000  LTP 00000000)
[    0.000000] ACPI: FACP 00000000bdfe7000 000F4 (v03 INTEL  CRESTLNE 06040000 ALAN 00000001)
[    0.000000] ACPI: DSDT 00000000bdfe8000 072A6 (v02 Intel  CANTIGA  06040000 INTL 20061109)
[    0.000000] ACPI: FACS 00000000bdf9efc0 00040
[    0.000000] ACPI: HPET 00000000bdffed16 00038 (v01 INTEL  CRESTLNE 06040000 LOHR 0000005A)
[    0.000000] ACPI: MCFG 00000000bdffed4e 0003C (v01 INTEL  CRESTLNE 06040000 LOHR 0000005A)
[    0.000000] ACPI: APIC 00000000bdffed8a 00068 (v01 PTLTD  ? APIC   06040000  LTP 00000000)
[    0.000000] ACPI: BOOT 00000000bdffedf2 00028 (v01 PTLTD  $SBFTBL$ 06040000  LTP 00000001)
[    0.000000] ACPI: SLIC 00000000bdffee1a 00176 (v01 DELL    QA09    06040000  LTP 00000000)
[    0.000000] ACPI: OSFR 00000000bdffef90 00070 (v01 DELL   DELL     06040000 ASL  00000061)
[    0.000000] ACPI: SSDT 00000000bdfe6000 00655 (v01  PmRef    CpuPm 00003000 INTL 20050624)
[    0.000000] ACPI: SSDT 00000000bdfe5000 00259 (v01  PmRef  Cpu0Tst 00003000 INTL 20050624)
[    0.000000] ACPI: SSDT 00000000bdfe4000 0020F (v01  PmRef    ApTst 00003000 INTL 20050624)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at 0000000000000000-0000000140000000
[    0.000000] Initmem setup node 0 0000000000000000-0000000140000000
[    0.000000]   NODE_DATA [000000013fffb000 - 000000013fffffff]
[    0.000000]  [ffffea0000000000-ffffea00045fffff] PMD -> [ffff88013b600000-ffff88013edfffff] on node 0
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   DMA32    0x00001000 -> 0x00100000
[    0.000000]   Normal   0x00100000 -> 0x00140000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[9] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009c
[    0.000000]     0: 0x00000100 -> 0x000bdaa1
[    0.000000]     0: 0x000bdaa7 -> 0x000bdbba
[    0.000000]     0: 0x000bdc0f -> 0x000bdd08
[    0.000000]     0: 0x000bdf0f -> 0x000bdf18
[    0.000000]     0: 0x000bdf1f -> 0x000bdf63
[    0.000000]     0: 0x000bdf9f -> 0x000bdfe3
[    0.000000]     0: 0x000bdfff -> 0x000be000
[    0.000000]     0: 0x00100000 -> 0x00140000
[    0.000000] On node 0 totalpages: 1039563
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 5 pages reserved
[    0.000000]   DMA zone: 3919 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 14280 pages used for memmap
[    0.000000]   DMA32 zone: 759159 pages, LIFO batch:31
[    0.000000]   Normal zone: 3584 pages used for memmap
[    0.000000]   Normal zone: 258560 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009c000 - 000000000009d000
[    0.000000] PM: Registered nosave memory: 000000000009d000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d2000
[    0.000000] PM: Registered nosave memory: 00000000000d2000 - 00000000000d4000
[    0.000000] PM: Registered nosave memory: 00000000000d4000 - 00000000000e0000
[    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[    0.000000] PM: Registered nosave memory: 00000000bdaa1000 - 00000000bdaa7000
[    0.000000] PM: Registered nosave memory: 00000000bdbba000 - 00000000bdc0f000
[    0.000000] PM: Registered nosave memory: 00000000bdd08000 - 00000000bdf0f000
[    0.000000] PM: Registered nosave memory: 00000000bdf18000 - 00000000bdf1f000
[    0.000000] PM: Registered nosave memory: 00000000bdf63000 - 00000000bdf9f000
[    0.000000] PM: Registered nosave memory: 00000000bdfe3000 - 00000000bdfff000
[    0.000000] PM: Registered nosave memory: 00000000be000000 - 0000000100000000
[    0.000000] Allocating PCI resources starting at be000000 (gap: be000000:42000000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:2 nr_node_ids:1
[    0.000000] PERCPU: Embedded 27 pages/cpu @ffff88013fc00000 s79232 r8192 d23168 u1048576
[    0.000000] pcpu-alloc: s79232 r8192 d23168 u1048576 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 1021638
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux-lts root=UUID=59eeed7d-54a3-45b8-8b17-2db45884a6b2 ro quiet nomodeset
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] xsave/xrstor: enabled xstate_bv 0x3, cntxt size 0x240
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 4020344k/5242880k available (4261k kernel code, 1084628k absent, 137908k reserved, 5156k data, 720k init)
[    0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Verbose stalled-CPUs detection is disabled.
[    0.000000] NR_IRQS:2304
[    0.000000] Extended CMOS year: 2000
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] allocated 33554432 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] hpet clockevent registered
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 2394.012 MHz processor.
[    0.010004] Calibrating delay loop (skipped), value calculated using timer frequency.. 4788.02 BogoMIPS (lpj=23940120)
[    0.010008] pid_max: default: 32768 minimum: 301
[    0.010126] Security Framework initialized
[    0.010132] AppArmor: AppArmor disabled by boot time parameter
[    0.010477] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.012513] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.013496] Mount-cache hash table entries: 256
[    0.013949] Initializing cgroup subsys cpuacct
[    0.013991] Initializing cgroup subsys memory
[    0.014019] Initializing cgroup subsys devices
[    0.014021] Initializing cgroup subsys freezer
[    0.014023] Initializing cgroup subsys net_cls
[    0.014025] Initializing cgroup subsys blkio
[    0.014078] CPU: Physical Processor ID: 0
[    0.014079] CPU: Processor Core ID: 0
[    0.014081] mce: CPU supports 6 MCE banks
[    0.014090] CPU0: Thermal monitoring enabled (TM2)
[    0.014094] using mwait in idle threads.
[    0.015210] ACPI: Core revision 20110413
[    0.030021] ftrace: allocating 16727 entries in 66 pages
[    0.037178] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.144002] CPU0: Intel(R) Core(TM)2 Duo CPU     P8600  @ 2.40GHz stepping 0a
[    0.150000] Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
[    0.150000] ... version:                2
[    0.150000] ... bit width:              40
[    0.150000] ... generic registers:      2
[    0.150000] ... value mask:             000000ffffffffff
[    0.150000] ... max period:             000000007fffffff
[    0.150000] ... fixed-purpose events:   3
[    0.150000] ... event mask:             0000000700000003
[    0.200082] NMI watchdog enabled, takes one hw-pmu counter.
[    0.280012] Booting Node   0, Processors  #1 Ok.
[    0.280015] smpboot cpu 1: start_ip = 97000
[    0.450027] NMI watchdog enabled, takes one hw-pmu counter.
[    0.470004] Brought up 2 CPUs
[    0.470006] Total of 2 processors activated (9575.96 BogoMIPS).
[    0.471479] devtmpfs: initialized
[    0.471479] PM: Registering ACPI NVS region at bdf63000 (245760 bytes)
[    0.471479] NET: Registered protocol family 16
[    0.471479] ACPI: bus type pci registered
[    0.471479] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.471479] PCI: not using MMCONFIG
[    0.471479] PCI: Using configuration type 1 for base access
[    0.471479] dmi type 0xB1 record - unknown flag
[    0.471479] mtrr: your CPUs had inconsistent variable MTRR settings
[    0.471479] mtrr: probably your BIOS does not setup all CPUs.
[    0.471479] mtrr: corrected configuration.
[    0.471593] bio: create slab <bio-0> at 0
[    0.471593] ACPI: EC: Look up EC in DSDT
[    0.500030] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[    0.505243] ACPI: SSDT 00000000bdf1ac20 00265 (v01  PmRef  Cpu0Ist 00003000 INTL 20050624)
[    0.505551] ACPI: Dynamic OEM Table Load:
[    0.505554] ACPI: SSDT           (null) 00265 (v01  PmRef  Cpu0Ist 00003000 INTL 20050624)
[    0.505660] ACPI: SSDT 00000000bdf18620 00575 (v01  PmRef  Cpu0Cst 00003001 INTL 20050624)
[    0.505955] ACPI: Dynamic OEM Table Load:
[    0.505957] ACPI: SSDT           (null) 00575 (v01  PmRef  Cpu0Cst 00003001 INTL 20050624)
[    0.560200] ACPI: SSDT 00000000bdf19ca0 001CF (v01  PmRef    ApIst 00003000 INTL 20050624)
[    0.560519] ACPI: Dynamic OEM Table Load:
[    0.560521] ACPI: SSDT           (null) 001CF (v01  PmRef    ApIst 00003000 INTL 20050624)
[    0.590076] ACPI: SSDT 00000000bdf19f20 0008D (v01  PmRef    ApCst 00003000 INTL 20050624)
[    0.590381] ACPI: Dynamic OEM Table Load:
[    0.590383] ACPI: SSDT           (null) 0008D (v01  PmRef    ApCst 00003000 INTL 20050624)
[    0.620255] ACPI: Interpreter enabled
[    0.620258] ACPI: (supports S0 S3 S4 S5)
[    0.620276] ACPI: Using IOAPIC for interrupt routing
[    0.620294] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.620591] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[    0.690320] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
[    0.690320] ACPI: No dock devices found.
[    0.690320] HEST: Table not found.
[    0.690320] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.690392] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.690823] pci_root PNP0A08:00: host bridge window [io  0x0000-0x0cf7]
[    0.690826] pci_root PNP0A08:00: host bridge window [io  0x0d00-0xffff]
[    0.690828] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[    0.690831] pci_root PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff]
[    0.690833] pci_root PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff]
[    0.690835] pci_root PNP0A08:00: host bridge window [mem 0x000dc000-0x000dffff]
[    0.690838] pci_root PNP0A08:00: host bridge window [mem 0xc0000000-0xfebfffff]
[    0.690849] pci 0000:00:00.0: [8086:2a40] type 0 class 0x000600
[    0.690868] DMAR: Forcing write-buffer flush capability
[    0.690870] DMAR: Disabling IOMMU for graphics on this chipset
[    0.690893] pci 0000:00:01.0: [8086:2a41] type 1 class 0x000604
[    0.690931] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.690935] pci 0000:00:01.0: PME# disabled
[    0.690986] pci 0000:00:1a.0: [8086:2937] type 0 class 0x000c03
[    0.691060] pci 0000:00:1a.0: reg 20: [io  0x1800-0x181f]
[    0.691143] pci 0000:00:1a.1: [8086:2938] type 0 class 0x000c03
[    0.691201] pci 0000:00:1a.1: reg 20: [io  0x1820-0x183f]
[    0.691273] pci 0000:00:1a.2: [8086:2939] type 0 class 0x000c03
[    0.691344] pci 0000:00:1a.2: reg 20: [io  0x1840-0x185f]
[    0.691439] pci 0000:00:1a.7: [8086:293c] type 0 class 0x000c03
[    0.691465] pci 0000:00:1a.7: reg 10: [mem 0xfc504800-0xfc504bff]
[    0.691577] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[    0.691582] pci 0000:00:1a.7: PME# disabled
[    0.691611] pci 0000:00:1b.0: [8086:293e] type 0 class 0x000403
[    0.691632] pci 0000:00:1b.0: reg 10: [mem 0xfc500000-0xfc503fff 64bit]
[    0.691730] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.691734] pci 0000:00:1b.0: PME# disabled
[    0.691759] pci 0000:00:1c.0: [8086:2940] type 1 class 0x000604
[    0.691862] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.691866] pci 0000:00:1c.0: PME# disabled
[    0.691894] pci 0000:00:1c.1: [8086:2942] type 1 class 0x000604
[    0.691996] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.692000] pci 0000:00:1c.1: PME# disabled
[    0.692029] pci 0000:00:1c.3: [8086:2946] type 1 class 0x000604
[    0.692131] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[    0.692135] pci 0000:00:1c.3: PME# disabled
[    0.692164] pci 0000:00:1c.5: [8086:294a] type 1 class 0x000604
[    0.692266] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[    0.692270] pci 0000:00:1c.5: PME# disabled
[    0.692303] pci 0000:00:1d.0: [8086:2934] type 0 class 0x000c03
[    0.692378] pci 0000:00:1d.0: reg 20: [io  0x1860-0x187f]
[    0.692461] pci 0000:00:1d.1: [8086:2935] type 0 class 0x000c03
[    0.692518] pci 0000:00:1d.1: reg 20: [io  0x1880-0x189f]
[    0.692587] pci 0000:00:1d.2: [8086:2936] type 0 class 0x000c03
[    0.692646] pci 0000:00:1d.2: reg 20: [io  0x18a0-0x18bf]
[    0.692724] pci 0000:00:1d.7: [8086:293a] type 0 class 0x000c03
[    0.692750] pci 0000:00:1d.7: reg 10: [mem 0xfc504c00-0xfc504fff]
[    0.692864] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.692868] pci 0000:00:1d.7: PME# disabled
[    0.692891] pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604
[    0.692979] pci 0000:00:1f.0: [8086:2919] type 0 class 0x000601
[    0.693139] pci 0000:00:1f.2: [8086:2929] type 0 class 0x000106
[    0.693166] pci 0000:00:1f.2: reg 10: [io  0x18f0-0x18f7]
[    0.693177] pci 0000:00:1f.2: reg 14: [io  0x18e4-0x18e7]
[    0.693188] pci 0000:00:1f.2: reg 18: [io  0x18e8-0x18ef]
[    0.693199] pci 0000:00:1f.2: reg 1c: [io  0x18e0-0x18e3]
[    0.693210] pci 0000:00:1f.2: reg 20: [io  0x18c0-0x18df]
[    0.693221] pci 0000:00:1f.2: reg 24: [mem 0xfc504000-0xfc5047ff]
[    0.693290] pci 0000:00:1f.2: PME# supported from D3hot
[    0.693294] pci 0000:00:1f.2: PME# disabled
[    0.693316] pci 0000:00:1f.3: [8086:2930] type 0 class 0x000c05
[    0.693337] pci 0000:00:1f.3: reg 10: [mem 0x00000000-0x000000ff 64bit]
[    0.693367] pci 0000:00:1f.3: reg 20: [io  0x1c00-0x1c1f]
[    0.693439] pci 0000:01:00.0: [1002:9553] type 0 class 0x000300
[    0.693454] pci 0000:01:00.0: reg 10: [mem 0xd0000000-0xdfffffff pref]
[    0.693465] pci 0000:01:00.0: reg 14: [io  0x2000-0x20ff]
[    0.693476] pci 0000:01:00.0: reg 18: [mem 0xfc000000-0xfc00ffff]
[    0.693514] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[    0.693563] pci 0000:01:00.0: supports D1 D2
[    0.693592] pci 0000:01:00.1: [1002:aa38] type 0 class 0x000403
[    0.693607] pci 0000:01:00.1: reg 10: [mem 0xfc010000-0xfc013fff]
[    0.693710] pci 0000:01:00.1: supports D1 D2
[    0.693757] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.693760] pci 0000:00:01.0:   bridge window [io  0x2000-0x2fff]
[    0.693764] pci 0000:00:01.0:   bridge window [mem 0xfc000000-0xfc0fffff]
[    0.693768] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.693824] pci 0000:00:1c.0: PCI bridge to [bus 02-03]
[    0.693829] pci 0000:00:1c.0:   bridge window [io  0x3000-0x3fff]
[    0.693833] pci 0000:00:1c.0:   bridge window [mem 0xf6000000-0xf7ffffff]
[    0.693841] pci 0000:00:1c.0:   bridge window [mem 0xf0000000-0xf1ffffff 64bit pref]
[    0.693947] pci 0000:04:00.0: [8086:4232] type 0 class 0x000280
[    0.693991] pci 0000:04:00.0: reg 10: [mem 0xf8000000-0xf8001fff 64bit]
[    0.694185] pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
[    0.694196] pci 0000:04:00.0: PME# disabled
[    0.710042] pci 0000:00:1c.1: PCI bridge to [bus 04-05]
[    0.710047] pci 0000:00:1c.1:   bridge window [io  0x4000-0x4fff]
[    0.710051] pci 0000:00:1c.1:   bridge window [mem 0xf8000000-0xf9ffffff]
[    0.710059] pci 0000:00:1c.1:   bridge window [mem 0xf2000000-0xf3ffffff 64bit pref]
[    0.710115] pci 0000:00:1c.3: PCI bridge to [bus 06-07]
[    0.710119] pci 0000:00:1c.3:   bridge window [io  0x5000-0x5fff]
[    0.710124] pci 0000:00:1c.3:   bridge window [mem 0xfa000000-0xfbffffff]
[    0.710132] pci 0000:00:1c.3:   bridge window [mem 0xf4000000-0xf5ffffff 64bit pref]
[    0.710371] pci 0000:08:00.0: [14e4:1698] type 0 class 0x000200
[    0.710400] pci 0000:08:00.0: reg 10: [mem 0xfc100000-0xfc10ffff 64bit]
[    0.710563] pci 0000:08:00.0: PME# supported from D3hot D3cold
[    0.710570] pci 0000:08:00.0: PME# disabled
[    0.730169] pci 0000:00:1c.5: PCI bridge to [bus 08-08]
[    0.730174] pci 0000:00:1c.5:   bridge window [io  0xf000-0x0000] (disabled)
[    0.730180] pci 0000:00:1c.5:   bridge window [mem 0xfc100000-0xfc1fffff]
[    0.730187] pci 0000:00:1c.5:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.730232] pci 0000:09:01.0: [1180:0832] type 0 class 0x000c00
[    0.730257] pci 0000:09:01.0: reg 10: [mem 0xfc200000-0xfc2007ff]
[    0.730362] pci 0000:09:01.0: supports D1 D2
[    0.730364] pci 0000:09:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.730370] pci 0000:09:01.0: PME# disabled
[    0.730391] pci 0000:09:01.1: [1180:0822] type 0 class 0x000805
[    0.730414] pci 0000:09:01.1: reg 10: [mem 0xfc200800-0xfc2008ff]
[    0.730518] pci 0000:09:01.1: supports D1 D2
[    0.730520] pci 0000:09:01.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.730525] pci 0000:09:01.1: PME# disabled
[    0.730546] pci 0000:09:01.2: [1180:0592] type 0 class 0x000880
[    0.730567] pci 0000:09:01.2: reg 10: [mem 0xfc200c00-0xfc200cff]
[    0.730672] pci 0000:09:01.2: supports D1 D2
[    0.730673] pci 0000:09:01.2: PME# supported from D0 D1 D2 D3hot D3cold
[    0.730678] pci 0000:09:01.2: PME# disabled
[    0.730699] pci 0000:09:01.3: [1180:0852] type 0 class 0x000880
[    0.730722] pci 0000:09:01.3: reg 10: [mem 0xfc201000-0xfc2010ff]
[    0.730828] pci 0000:09:01.3: supports D1 D2
[    0.730830] pci 0000:09:01.3: PME# supported from D0 D1 D2 D3hot D3cold
[    0.730835] pci 0000:09:01.3: PME# disabled
[    0.730904] pci 0000:00:1e.0: PCI bridge to [bus 09-09] (subtractive decode)
[    0.730909] pci 0000:00:1e.0:   bridge window [io  0xf000-0x0000] (disabled)
[    0.730914] pci 0000:00:1e.0:   bridge window [mem 0xfc200000-0xfc2fffff]
[    0.730922] pci 0000:00:1e.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.730924] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.730927] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.730930] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.730933] pci 0000:00:1e.0:   bridge window [mem 0x000d4000-0x000d7fff] (subtractive decode)
[    0.730936] pci 0000:00:1e.0:   bridge window [mem 0x000d8000-0x000dbfff] (subtractive decode)
[    0.730938] pci 0000:00:1e.0:   bridge window [mem 0x000dc000-0x000dffff] (subtractive decode)
[    0.730941] pci 0000:00:1e.0:   bridge window [mem 0xc0000000-0xfebfffff] (subtractive decode)
[    0.730975] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.731044] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
[    0.731073] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[    0.731122] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[    0.731152] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[    0.731180] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
[    0.731203] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP06._PRT]
[    0.731236]  pci0000:00: Requesting ACPI _OSC control (0x1d)
[    0.731239]  pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d
[    0.731240] ACPI _OSC control for PCIe not granted, disabling ASPM
[    0.735743] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 12 14 15)
[    0.735785] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[    0.735824] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[    0.735863] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[    0.735903] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[    0.735942] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[    0.735981] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[    0.736020] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 *7 11 12 14 15)
[    0.736108] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.736113] vgaarb: loaded
[    0.736114] vgaarb: bridge control possible 0000:01:00.0
[    0.736156] PCI: Using ACPI for IRQ routing
[    0.746235] PCI: pci_cache_line_size set to 64 bytes
[    0.746534] reserve RAM buffer: 000000000009c400 - 000000000009ffff 
[    0.746538] reserve RAM buffer: 00000000bdaa1000 - 00000000bfffffff 
[    0.746541] reserve RAM buffer: 00000000bdbba000 - 00000000bfffffff 
[    0.746544] reserve RAM buffer: 00000000bdd08000 - 00000000bfffffff 
[    0.746547] reserve RAM buffer: 00000000bdf18000 - 00000000bfffffff 
[    0.746549] reserve RAM buffer: 00000000bdf63000 - 00000000bfffffff 
[    0.746552] reserve RAM buffer: 00000000bdfe3000 - 00000000bfffffff 
[    0.746554] reserve RAM buffer: 00000000be000000 - 00000000bfffffff 
[    0.746671] NetLabel: Initializing
[    0.746673] NetLabel:  domain hash size = 128
[    0.746674] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.746688] NetLabel:  unlabeled traffic allowed by default
[    0.746694] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[    0.746699] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[    0.746703] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[    0.790021] Switching to clocksource hpet
[    0.796147] pnp: PnP ACPI init
[    0.796165] ACPI: bus type pnp registered
[    0.796430] pnp 00:00: [bus 00-ff]
[    0.796432] pnp 00:00: [io  0x0000-0x0cf7 window]
[    0.796434] pnp 00:00: [io  0x0cf8-0x0cff]
[    0.796436] pnp 00:00: [io  0x0d00-0xffff window]
[    0.796438] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[    0.796440] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[    0.796442] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[    0.796444] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[    0.796446] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[    0.796448] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[    0.796450] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[    0.796451] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[    0.796453] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[    0.796455] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[    0.796457] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[    0.796459] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[    0.796461] pnp 00:00: [mem 0x000ec000-0x000effff window]
[    0.796463] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[    0.796465] pnp 00:00: [mem 0xc0000000-0xfebfffff window]
[    0.796467] pnp 00:00: [mem 0xfed40000-0xfed44fff window]
[    0.796531] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[    0.796579] pnp 00:01: [io  0x0000-0x001f]
[    0.796581] pnp 00:01: [io  0x0081-0x0091]
[    0.796582] pnp 00:01: [io  0x0093-0x009f]
[    0.796584] pnp 00:01: [io  0x00c0-0x00df]
[    0.796586] pnp 00:01: [dma 4]
[    0.796612] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.796677] pnp 00:02: [mem 0xfed00000-0xfed003ff]
[    0.796738] system 00:02: [mem 0xfed00000-0xfed003ff] has been reserved
[    0.796742] system 00:02: Plug and Play ACPI device, IDs PNP0103 PNP0c01 (active)
[    0.796751] pnp 00:03: [io  0x00f0]
[    0.796762] pnp 00:03: [irq 13]
[    0.796784] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.796795] pnp 00:04: [io  0x002e-0x002f]
[    0.796797] pnp 00:04: [io  0x004e-0x004f]
[    0.796798] pnp 00:04: [io  0x0061]
[    0.796800] pnp 00:04: [io  0x0063]
[    0.796801] pnp 00:04: [io  0x0065]
[    0.796803] pnp 00:04: [io  0x0067]
[    0.796805] pnp 00:04: [io  0x0068]
[    0.796806] pnp 00:04: [io  0x006c]
[    0.796807] pnp 00:04: [io  0x0070]
[    0.796809] pnp 00:04: [io  0x0080]
[    0.796810] pnp 00:04: [io  0x0092]
[    0.796812] pnp 00:04: [io  0x00b2-0x00b3]
[    0.796814] pnp 00:04: [io  0x0400-0x047f]
[    0.796815] pnp 00:04: [io  0x0680-0x069f]
[    0.796817] pnp 00:04: [io  0x0480-0x048f]
[    0.796819] pnp 00:04: [io  0xffff]
[    0.796820] pnp 00:04: [io  0xffff]
[    0.796822] pnp 00:04: [io  0x1000-0x107f]
[    0.796823] pnp 00:04: [io  0x1180-0x11ff]
[    0.796825] pnp 00:04: [io  0x164e-0x164f]
[    0.796826] pnp 00:04: [io  0xfe00]
[    0.796828] pnp 00:04: [io  0x0900-0x097f]
[    0.796884] system 00:04: [io  0x0400-0x047f] has been reserved
[    0.796887] system 00:04: [io  0x0680-0x069f] has been reserved
[    0.796889] system 00:04: [io  0x0480-0x048f] has been reserved
[    0.796891] system 00:04: [io  0xffff] has been reserved
[    0.796893] system 00:04: [io  0xffff] has been reserved
[    0.796895] system 00:04: [io  0x1000-0x107f] has been reserved
[    0.796898] system 00:04: [io  0x1180-0x11ff] has been reserved
[    0.796900] system 00:04: [io  0x164e-0x164f] has been reserved
[    0.796902] system 00:04: [io  0xfe00] has been reserved
[    0.796904] system 00:04: [io  0x0900-0x097f] has been reserved
[    0.796907] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.796915] pnp 00:05: [io  0x0070-0x0077]
[    0.796920] pnp 00:05: [irq 8]
[    0.796942] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.796951] pnp 00:06: [io  0x0060]
[    0.796953] pnp 00:06: [io  0x0064]
[    0.796958] pnp 00:06: [irq 1]
[    0.796980] pnp 00:06: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.796994] pnp 00:07: [irq 12]
[    0.797020] pnp 00:07: Plug and Play ACPI device, IDs PNP0f13 (active)
[    0.797128] pnp 00:08: [mem 0xfed1c000-0xfed1ffff]
[    0.797130] pnp 00:08: [mem 0xfed10000-0xfed13fff]
[    0.797132] pnp 00:08: [mem 0xfed18000-0xfed18fff]
[    0.797134] pnp 00:08: [mem 0xfed19000-0xfed19fff]
[    0.797135] pnp 00:08: [mem 0xe0000000-0xefffffff]
[    0.797137] pnp 00:08: [mem 0xfeb00000-0xfeb03fff]
[    0.797139] pnp 00:08: [mem 0xfed20000-0xfed3ffff]
[    0.797143] pnp 00:08: [mem 0xfed40000-0xfed44fff]
[    0.797145] pnp 00:08: [mem 0xfed45000-0xfed8ffff]
[    0.797199] system 00:08: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.797201] system 00:08: [mem 0xfed10000-0xfed13fff] has been reserved
[    0.797204] system 00:08: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.797206] system 00:08: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.797208] system 00:08: [mem 0xe0000000-0xefffffff] has been reserved
[    0.797211] system 00:08: [mem 0xfeb00000-0xfeb03fff] has been reserved
[    0.797213] system 00:08: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.797216] system 00:08: [mem 0xfed40000-0xfed44fff] has been reserved
[    0.797218] system 00:08: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.797221] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.797964] pnp: PnP ACPI: found 9 devices
[    0.797965] ACPI: ACPI bus type pnp unregistered
[    0.799933] Switched to NOHz mode on CPU #0
[    0.799978] Switched to NOHz mode on CPU #1
[    0.804052] PCI: max bus depth: 1 pci_try_num: 2
[    0.804109] pci 0000:00:1f.3: BAR 0: assigned [mem 0xc0000000-0xc00000ff 64bit]
[    0.804118] pci 0000:00:1f.3: BAR 0: set to [mem 0xc0000000-0xc00000ff 64bit] (PCI address [0xc0000000-0xc00000ff])
[    0.804122] pci 0000:00:1c.5: BAR 15: assigned [mem 0xc0100000-0xc02fffff 64bit pref]
[    0.804125] pci 0000:00:1c.5: BAR 13: assigned [io  0x6000-0x6fff]
[    0.804129] pci 0000:01:00.0: BAR 6: assigned [mem 0xfc020000-0xfc03ffff pref]
[    0.804131] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.804134] pci 0000:00:01.0:   bridge window [io  0x2000-0x2fff]
[    0.804137] pci 0000:00:01.0:   bridge window [mem 0xfc000000-0xfc0fffff]
[    0.804140] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.804144] pci 0000:00:1c.0: PCI bridge to [bus 02-03]
[    0.804148] pci 0000:00:1c.0:   bridge window [io  0x3000-0x3fff]
[    0.804153] pci 0000:00:1c.0:   bridge window [mem 0xf6000000-0xf7ffffff]
[    0.804158] pci 0000:00:1c.0:   bridge window [mem 0xf0000000-0xf1ffffff 64bit pref]
[    0.804165] pci 0000:00:1c.1: PCI bridge to [bus 04-05]
[    0.804168] pci 0000:00:1c.1:   bridge window [io  0x4000-0x4fff]
[    0.804174] pci 0000:00:1c.1:   bridge window [mem 0xf8000000-0xf9ffffff]
[    0.804178] pci 0000:00:1c.1:   bridge window [mem 0xf2000000-0xf3ffffff 64bit pref]
[    0.804185] pci 0000:00:1c.3: PCI bridge to [bus 06-07]
[    0.804188] pci 0000:00:1c.3:   bridge window [io  0x5000-0x5fff]
[    0.804194] pci 0000:00:1c.3:   bridge window [mem 0xfa000000-0xfbffffff]
[    0.804198] pci 0000:00:1c.3:   bridge window [mem 0xf4000000-0xf5ffffff 64bit pref]
[    0.804205] pci 0000:00:1c.5: PCI bridge to [bus 08-08]
[    0.804209] pci 0000:00:1c.5:   bridge window [io  0x6000-0x6fff]
[    0.804214] pci 0000:00:1c.5:   bridge window [mem 0xfc100000-0xfc1fffff]
[    0.804219] pci 0000:00:1c.5:   bridge window [mem 0xc0100000-0xc02fffff 64bit pref]
[    0.804226] pci 0000:00:1e.0: PCI bridge to [bus 09-09]
[    0.804228] pci 0000:00:1e.0:   bridge window [io  disabled]
[    0.804234] pci 0000:00:1e.0:   bridge window [mem 0xfc200000-0xfc2fffff]
[    0.804238] pci 0000:00:1e.0:   bridge window [mem pref disabled]
[    0.804252] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.804256] pci 0000:00:01.0: setting latency timer to 64
[    0.804264] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    0.804268] pci 0000:00:1c.0: setting latency timer to 64
[    0.804275] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[    0.804279] pci 0000:00:1c.1: setting latency timer to 64
[    0.804286] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    0.804291] pci 0000:00:1c.3: setting latency timer to 64
[    0.804297] pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[    0.804301] pci 0000:00:1c.5: setting latency timer to 64
[    0.804308] pci 0000:00:1e.0: setting latency timer to 64
[    0.804312] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.804314] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.804316] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.804318] pci_bus 0000:00: resource 7 [mem 0x000d4000-0x000d7fff]
[    0.804320] pci_bus 0000:00: resource 8 [mem 0x000d8000-0x000dbfff]
[    0.804323] pci_bus 0000:00: resource 9 [mem 0x000dc000-0x000dffff]
[    0.804325] pci_bus 0000:00: resource 10 [mem 0xc0000000-0xfebfffff]
[    0.804327] pci_bus 0000:01: resource 0 [io  0x2000-0x2fff]
[    0.804329] pci_bus 0000:01: resource 1 [mem 0xfc000000-0xfc0fffff]
[    0.804331] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.804334] pci_bus 0000:02: resource 0 [io  0x3000-0x3fff]
[    0.804336] pci_bus 0000:02: resource 1 [mem 0xf6000000-0xf7ffffff]
[    0.804338] pci_bus 0000:02: resource 2 [mem 0xf0000000-0xf1ffffff 64bit pref]
[    0.804340] pci_bus 0000:04: resource 0 [io  0x4000-0x4fff]
[    0.804342] pci_bus 0000:04: resource 1 [mem 0xf8000000-0xf9ffffff]
[    0.804344] pci_bus 0000:04: resource 2 [mem 0xf2000000-0xf3ffffff 64bit pref]
[    0.804346] pci_bus 0000:06: resource 0 [io  0x5000-0x5fff]
[    0.804348] pci_bus 0000:06: resource 1 [mem 0xfa000000-0xfbffffff]
[    0.804350] pci_bus 0000:06: resource 2 [mem 0xf4000000-0xf5ffffff 64bit pref]
[    0.804353] pci_bus 0000:08: resource 0 [io  0x6000-0x6fff]
[    0.804355] pci_bus 0000:08: resource 1 [mem 0xfc100000-0xfc1fffff]
[    0.804357] pci_bus 0000:08: resource 2 [mem 0xc0100000-0xc02fffff 64bit pref]
[    0.804359] pci_bus 0000:09: resource 1 [mem 0xfc200000-0xfc2fffff]
[    0.804361] pci_bus 0000:09: resource 4 [io  0x0000-0x0cf7]
[    0.804363] pci_bus 0000:09: resource 5 [io  0x0d00-0xffff]
[    0.804365] pci_bus 0000:09: resource 6 [mem 0x000a0000-0x000bffff]
[    0.804367] pci_bus 0000:09: resource 7 [mem 0x000d4000-0x000d7fff]
[    0.804369] pci_bus 0000:09: resource 8 [mem 0x000d8000-0x000dbfff]
[    0.804371] pci_bus 0000:09: resource 9 [mem 0x000dc000-0x000dffff]
[    0.804373] pci_bus 0000:09: resource 10 [mem 0xc0000000-0xfebfffff]
[    0.804446] NET: Registered protocol family 2
[    0.804634] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.805705] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[    0.809428] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.809916] TCP: Hash tables configured (established 524288 bind 65536)
[    0.809918] TCP reno registered
[    0.809932] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.809971] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.810445] NET: Registered protocol family 1
[    0.810477] pci 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.810497] pci 0000:00:1a.0: PCI INT A disabled
[    0.810511] pci 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[    0.810529] pci 0000:00:1a.1: PCI INT B disabled
[    0.810537] pci 0000:00:1a.2: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[    0.810556] pci 0000:00:1a.2: PCI INT C disabled
[    0.810566] pci 0000:00:1a.7: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[    0.810598] pci 0000:00:1a.7: PCI INT C disabled
[    0.810619] pci 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    0.810637] pci 0000:00:1d.0: PCI INT A disabled
[    0.810645] pci 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    0.810663] pci 0000:00:1d.1: PCI INT B disabled
[    0.810672] pci 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    0.810690] pci 0000:00:1d.2: PCI INT C disabled
[    0.810699] pci 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    0.810724] pci 0000:00:1d.7: PCI INT A disabled
[    0.810740] pci 0000:01:00.0: Boot video device
[    0.810936] PCI: CLS 64 bytes, default 64
[    0.810998] Unpacking initramfs...
[    0.861964] Freeing initrd memory: 2528k freed
[    0.862775] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.862779] Placing 64MB software IO TLB between ffff8800b9aa1000 - ffff8800bdaa1000
[    0.862782] software IO TLB at phys 0xb9aa1000 - 0xbdaa1000
[    0.862807] Simple Boot Flag at 0x36 set to 0x1
[    0.863176] audit: initializing netlink socket (disabled)
[    0.863188] type=2000 audit(1342909589.860:1): initialized
[    0.873821] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.899732] VFS: Disk quotas dquot_6.5.2
[    0.899864] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.900064] msgmni has been set to 7857
[    0.900285] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.900322] io scheduler noop registered
[    0.900324] io scheduler deadline registered (default)
[    0.900371] io scheduler cfq registered
[    0.900478] pcieport 0000:00:01.0: setting latency timer to 64
[    0.900505] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[    0.900552] pcieport 0000:00:1c.0: setting latency timer to 64
[    0.900601] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[    0.900671] pcieport 0000:00:1c.1: setting latency timer to 64
[    0.900718] pcieport 0000:00:1c.1: irq 42 for MSI/MSI-X
[    0.900790] pcieport 0000:00:1c.3: setting latency timer to 64
[    0.900838] pcieport 0000:00:1c.3: irq 43 for MSI/MSI-X
[    0.900907] pcieport 0000:00:1c.5: setting latency timer to 64
[    0.900955] pcieport 0000:00:1c.5: irq 44 for MSI/MSI-X
[    0.901080] vesafb: mode is 1024x768x32, linelength=4096, pages=0
[    0.901082] vesafb: scrolling: redraw
[    0.901084] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
[    0.902020] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90011100000, using 3072k, total 3072k
[    0.937741] Console: switching to colour frame buffer device 128x48
[    0.973421] fb0: VESA VGA frame buffer device
[    0.973431] intel_idle: MWAIT substates: 0x3122220
[    0.973433] intel_idle: does not run on family 6 model 23
[    0.973437] ERST: Table is not found!
[    0.973482] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    1.540223] Linux agpgart interface v0.103
[    1.540293] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    1.547512] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.547542] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.547615] mousedev: PS/2 mouse device common for all mice
[    1.547783] rtc_cmos 00:05: RTC can wake from S4
[    1.547877] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[    1.547906] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    1.547914] cpuidle: using governor ladder
[    1.547916] cpuidle: using governor menu
[    1.548135] TCP cubic registered
[    1.548279] NET: Registered protocol family 10
[    1.548885] NET: Registered protocol family 17
[    1.548890] Registering the dns_resolver key type
[    1.548983] PM: Hibernation image not present or could not be loaded.
[    1.548988] registered taskstats version 1
[    1.559520] rtc_cmos 00:05: setting system clock to 2012-07-21 22:26:33 UTC (1342909593)
[    1.559574] Initializing network drop monitor service
[    1.560636] Freeing unused kernel memory: 720k freed
[    1.560790] Write protecting the kernel read-only data: 8192k
[    1.566077] Freeing unused kernel memory: 1864k freed
[    1.568447] Freeing unused kernel memory: 712k freed
[    1.570549] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    1.576586] systemd-udevd[37]: starting version 186
[    1.603286] usbcore: registered new interface driver usbfs
[    1.603309] usbcore: registered new interface driver hub
[    1.609076] usbcore: registered new device driver usb
[    1.609695] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.609732] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[    1.609771] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[    1.609775] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[    1.609796] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[    1.609832] ehci_hcd 0000:00:1a.7: debug port 1
[    1.612016] SCSI subsystem initialized
[    1.613728] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
[    1.613748] ehci_hcd 0000:00:1a.7: irq 19, io mem 0xfc504800
[    1.614316] libata version 3.00 loaded.
[    1.620554] uhci_hcd: USB Universal Host Controller Interface driver
[    1.630028] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[    1.630156] hub 1-0:1.0: USB hub found
[    1.630161] hub 1-0:1.0: 6 ports detected
[    1.630273] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    1.630309] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    1.630313] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    1.630321] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[    1.630898] ehci_hcd 0000:00:1d.7: debug port 1
[    1.634779] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[    1.634798] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfc504c00
[    1.650019] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    1.650148] hub 2-0:1.0: USB hub found
[    1.650152] hub 2-0:1.0: 6 ports detected
[    1.650408] ahci 0000:00:1f.2: version 3.0
[    1.650419] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    1.650473] ahci 0000:00:1f.2: irq 45 for MSI/MSI-X
[    1.650547] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x23 impl SATA mode
[    1.650551] ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pmp pio slum part ccc sxs 
[    1.650556] ahci 0000:00:1f.2: setting latency timer to 64
[    1.651570] scsi0 : ahci
[    1.651674] scsi1 : ahci
[    1.651742] scsi2 : ahci
[    1.651807] scsi3 : ahci
[    1.651870] scsi4 : ahci
[    1.651933] scsi5 : ahci
[    1.651989] ata1: SATA max UDMA/133 abar m2048@0xfc504000 port 0xfc504100 irq 45
[    1.651993] ata2: SATA max UDMA/133 abar m2048@0xfc504000 port 0xfc504180 irq 45
[    1.651995] ata3: DUMMY
[    1.651996] ata4: DUMMY
[    1.651997] ata5: DUMMY
[    1.651999] ata6: SATA max UDMA/133 abar m2048@0xfc504000 port 0xfc504380 irq 45
[    1.652028] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.652037] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[    1.652041] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[    1.652051] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[    1.652090] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001800
[    1.652217] hub 3-0:1.0: USB hub found
[    1.652221] hub 3-0:1.0: 2 ports detected
[    1.652286] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[    1.652293] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[    1.652297] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[    1.652304] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[    1.652338] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001820
[    1.652447] hub 4-0:1.0: USB hub found
[    1.652451] hub 4-0:1.0: 2 ports detected
[    1.652512] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[    1.652519] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[    1.652522] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[    1.652529] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[    1.652556] uhci_hcd 0000:00:1a.2: irq 19, io base 0x00001840
[    1.652662] hub 5-0:1.0: USB hub found
[    1.652666] hub 5-0:1.0: 2 ports detected
[    1.652727] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    1.652735] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    1.652738] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    1.652744] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[    1.652769] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001860
[    1.652878] hub 6-0:1.0: USB hub found
[    1.652881] hub 6-0:1.0: 2 ports detected
[    1.653278] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    1.653286] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    1.653290] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    1.653296] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[    1.653321] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001880
[    1.653439] hub 7-0:1.0: USB hub found
[    1.653443] hub 7-0:1.0: 2 ports detected
[    1.653506] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    1.653513] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    1.653517] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    1.653523] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[    1.653556] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018a0
[    1.653664] hub 8-0:1.0: USB hub found
[    1.653667] hub 8-0:1.0: 2 ports detected
[    1.860021] Refined TSC clocksource calibration: 2393.999 MHz.
[    1.860026] Switching to clocksource tsc
[    2.000047] ata6: SATA link down (SStatus 0 SControl 300)
[    2.070010] usb 1-6: new high speed USB device number 3 using ehci_hcd
[    2.200014] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    2.200034] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    2.200306] ata1.00: ATA-8: INTEL SSDSA2CW120G3, 4PC10362, max UDMA/133
[    2.200309] ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32)
[    2.200607] ata1.00: configured for UDMA/133
[    2.200719] scsi 0:0:0:0: Direct-Access     ATA      INTEL SSDSA2CW12 4PC1 PQ: 0 ANSI: 5
[    2.205766] ata2.00: ATA-8: WDC WD10TPVT-00U4RT1, 01.01A01, max UDMA/133
[    2.205769] ata2.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    2.211833] ata2.00: configured for UDMA/133
[    2.211894] scsi 1:0:0:0: Direct-Access     ATA      WDC WD10TPVT-00U 01.0 PQ: 0 ANSI: 5
[    2.216318] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
[    2.216377] sd 0:0:0:0: [sda] Write Protect is off
[    2.216380] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.216399] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    2.216781] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[    2.216784] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[    2.216824] sd 1:0:0:0: [sdb] Write Protect is off
[    2.216827] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    2.216845] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.216966]  sda: sda1 sda2 sda3 sda4
[    2.217303] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.410010] usb 2-1: new high speed USB device number 2 using ehci_hcd
[    2.542426]  sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 >
[    2.542722] sd 1:0:0:0: [sdb] Attached SCSI disk
[    2.561635] hub 2-1:1.0: USB hub found
[    2.561974] hub 2-1:1.0: 4 ports detected
[    2.900020] usb 3-1: new full speed USB device number 2 using uhci_hcd
[    3.088159] hub 3-1:1.0: USB hub found
[    3.090131] hub 3-1:1.0: 3 ports detected
[    3.370009] usb 6-2: new low speed USB device number 2 using uhci_hcd
[    3.569044] input: DELL DELL USB Laser Mouse as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.0/input/input1
[    3.569107] generic-usb 0003:046D:C063.0001: input,hidraw0: USB HID v1.10 Mouse [DELL DELL USB Laser Mouse] on usb-0000:00:1d.0-2/input0
[    3.569119] usbcore: registered new interface driver usbhid
[    3.569121] usbhid: USB HID core driver
[    3.631130] usb 3-1.1: new full speed USB device number 3 using uhci_hcd
[    3.767343] input: HID 413c:8157 as /devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.1/3-1.1:1.0/input/input2
[    3.767393] generic-usb 0003:413C:8157.0002: input,hidraw1: USB HID v1.11 Keyboard [HID 413c:8157] on usb-0000:00:1a.0-1.1/input0
[    3.841131] usb 3-1.2: new full speed USB device number 4 using uhci_hcd
[    3.978439] input: HID 413c:8158 as /devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.2/3-1.2:1.0/input/input3
[    3.978511] generic-usb 0003:413C:8158.0003: input,hidraw2: USB HID v1.11 Mouse [HID 413c:8158] on usb-0000:00:1a.0-1.2/input0
[    4.229680] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[    4.565420] systemd-udevd[131]: starting version 186
[    4.610929] fuse init (API version 7.16)
[    4.616997] ACPI: acpi_idle registered with cpuidle
[    4.632517] Monitor-Mwait will be used to enter C-1 state
[    4.644056] Monitor-Mwait will be used to enter C-2 state
[    4.650496] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
[    4.650503] ACPI: Power Button [PWRB]
[    4.650546] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input5
[    4.650549] ACPI: Sleep Button [SLPB]
[    4.650595] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input6
[    4.651744] ACPI: Lid Switch [LID0]
[    4.654191] Monitor-Mwait will be used to enter C-3 state
[    4.654213] Marking TSC unstable due to TSC halts in idle
[    4.664829] Switching to clocksource hpet
[    4.667189] thermal LNXTHERM:00: registered as thermal_zone0
[    4.667192] ACPI: Thermal Zone [TZ00] (61 C)
[    4.676131] ACPI Warning: _BQC returned an invalid level (20110413/video-473)
[    4.688172] thermal LNXTHERM:01: registered as thermal_zone1
[    4.688175] ACPI: Thermal Zone [TZ01] (55 C)
[    4.689369] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input7
[    4.689375] ACPI: Power Button [PWRF]
[    4.690684] thermal LNXTHERM:02: registered as thermal_zone2
[    4.690687] ACPI: Thermal Zone [TZ02] (63 C)
[    4.708155] iTCO_vendor_support: vendor-support=0
[    4.712464] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[    4.712470] ACPI: resource 0000:00:1f.3 [io  0x1c00-0x1c1f] conflicts with ACPI region SMBI [io 0x1c00-0x1c0f]
[    4.712472] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    4.712531] acpi device:03: registered as cooling_device2
[    4.712613] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input8
[    4.712619] ACPI: Video Device [M86] (multi-head: yes  rom: no  post: no)
[    4.772319] Linux media interface: v0.10
[    4.774712] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[    4.860455] ACPI: AC Adapter [ADP1] (on-line)
[    4.887466] ACPI: Battery Slot [BAT0] (battery present)
[    4.888563] wmi: Mapper loaded
[    4.890409] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
[    4.890517] iTCO_wdt: Found a ICH9M TCO device (Version=2, TCOBASE=0x0460)
[    4.890596] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    4.890769] sdhci: Secure Digital Host Controller Interface driver
[    4.890771] sdhci: Copyright(c) Pierre Ossman
[    4.892943] r592 0000:09:01.2: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[    4.901135] cfg80211: Calling CRDA to update world regulatory domain
[    4.901299] r592: driver successfully loaded
[    4.901486] sdhci-pci 0000:09:01.1: SDHCI controller found [1180:0822] (rev 22)
[    4.901503] sdhci-pci 0000:09:01.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[    4.902116] tg3.c:v3.119 (May 18, 2011)
[    4.902280] tg3 0000:08:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    4.902290] tg3 0000:08:00.0: setting latency timer to 64
[    4.903586] Registered led device: mmc0::
[    4.904189] Linux video capture interface: v2.00
[    4.914664] mmc0: SDHCI controller on PCI [0000:09:01.1] using DMA
[    4.956773] firewire_ohci 0000:09:01.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    4.968613] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_2M (0c45:63ea)
[    4.975602] input: Laptop_Integrated_Webcam_2M as /devices/pci0000:00/0000:00:1a.7/usb1/1-6/1-6:1.0/input/input9
[    4.975668] usbcore: registered new interface driver uvcvideo
[    4.975670] USB Video Class driver (v1.1.0)
[    4.979030] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    4.985213] [drm] Initialized drm 1.1.0 20060810
[    4.986533] tg3 0000:08:00.0: eth0: Tigon3 [partno(BCM95784M) rev 5784100] (PCI Express) MAC address 00:22:19:ed:1f:24
[    4.986537] tg3 0000:08:00.0: eth0: attached PHY is 5784 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
[    4.986541] tg3 0000:08:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[    4.986543] tg3 0000:08:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[    4.987749] HDA Intel 0000:00:1b.0: irq 46 for MSI/MSI-X
[    4.987783] HDA Intel 0000:00:1b.0: setting latency timer to 64
[    4.990615] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree:
[    4.990618] iwlagn: Copyright(c) 2003-2011 Intel Corporation
[    4.990737] iwlagn 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    4.990811] iwlagn 0000:04:00.0: setting latency timer to 64
[    4.990896] iwlagn 0000:04:00.0: Detected Intel(R) WiFi Link 5100 AGN, REV=0x54
[    5.010179] firewire_ohci: Added fw-ohci device 0000:09:01.0, OHCI v1.10, 4 IR + 4 IT contexts, quirks 0x11
[    5.010769] r852 0000:09:01.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[    5.013832] iwlagn 0000:04:00.0: device EEPROM VER=0x11f, CALIB=0x4
[    5.013835] iwlagn 0000:04:00.0: Device SKU: 0Xb
[    5.013849] iwlagn 0000:04:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels
[    5.013972] iwlagn 0000:04:00.0: irq 47 for MSI/MSI-X
[    5.014180] r852: driver loaded successfully
[    5.016379] [drm] VGACON disable radeon kernel modesetting.
[    5.017330] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    5.017336] pci 0000:01:00.0: setting latency timer to 64
[    5.017502] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[    5.017504] [drm] No driver support for vblank timestamp query.
[    5.017507] [drm] Initialized radeon 1.33.0 20080528 for 0000:01:00.0 on minor 0
[    5.059319] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[    5.059324] Disabling lock debugging due to kernel taint
[    5.084163] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input10
[    5.121725] input: HDA Intel Mic at Ext Left Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[    5.121783] input: HDA Intel HP Out at Ext Left Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[    5.121842] input: HDA Intel HP Out at Ext Left Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
[    5.122004] HDA Intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    5.122082] HDA Intel 0000:01:00.1: irq 48 for MSI/MSI-X
[    5.122111] HDA Intel 0000:01:00.1: setting latency timer to 64
[    5.150860] [fglrx] Maximum main memory to use for locked dma buffers: 3769 MBytes.
[    5.151263] [fglrx]   vendor: 1002 device: 9553 count: 1
[    5.151900] [fglrx] ioport: bar 1, base 0x2000, size: 0x100
[    5.151908] pci 0000:01:00.0: setting latency timer to 64
[    5.152170] [fglrx] Kernel PAT support is enabled
[    5.152189] [fglrx] module loaded - fglrx 8.96.4 [Apr  5 2012] with 1 minors
[    5.168234] HDMI status: Pin=3 Presence_Detect=0 ELD_Valid=0
[    5.168489] input: HDA ATI HDMI HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input14
[    5.412389] usb 3-1.3: new full speed USB device number 5 using uhci_hcd
[    5.510318] firewire_core: created device fw0: GUID 484fc0003d440d58, S400
[    5.526172] input: Dell WMI hotkeys as /devices/virtual/input/input15
[    5.552412] iwlagn 0000:04:00.0: loaded firmware version 8.83.5.1 build 33692
[    5.553695] Registered led device: phy0-led
[    5.558834] Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000
[    5.559867] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs'
[    5.586093] Bluetooth: Core ver 2.16
[    5.586269] NET: Registered protocol family 31
[    5.586271] Bluetooth: HCI device and connection manager initialized
[    5.586274] Bluetooth: HCI socket layer initialized
[    5.586275] Bluetooth: L2CAP socket layer initialized
[    5.586330] Bluetooth: SCO socket layer initialized
[    5.587788] Bluetooth: Generic Bluetooth USB driver ver 0.6
[    5.590336] usbcore: registered new interface driver btusb
[    5.602043] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input16
[    7.452780] EXT4-fs (sda2): re-mounted. Opts: discard
[    7.586000] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[    8.672889] Adding 995324k swap on /dev/sda3.  Priority:-1 extents:1 across:995324k SS

and my xorg.0.log

[    15.739] 
X.Org X Server 1.11.4
Release Date: 2012-01-27
[    15.739] X Protocol Version 11, Revision 0
[    15.739] Build Operating System: Linux 3.3.7-1-ARCH x86_64 
[    15.739] Current Operating System: Linux phoenix 3.0.36-2-lts #1 SMP PREEMPT Tue Jul 3 15:04:30 UTC 2012 x86_64
[    15.739] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux-lts root=UUID=59eeed7d-54a3-45b8-8b17-2db45884a6b2 ro quiet nomodeset
[    15.739] Build Date: 01 June 2012  05:44:06PM
[    15.739]  
[    15.739] Current version of pixman: 0.26.2
[    15.739] 	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
[    15.739] Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    15.739] (==) Log file: "/var/log/Xorg.0.log", Time: Sat Jul 21 22:26:47 2012
[    15.741] (==) Using config file: "/etc/X11/xorg.conf"
[    15.741] (==) Using config directory: "/etc/X11/xorg.conf.d"
[    15.742] (==) ServerLayout "aticonfig Layout"
[    15.742] (**) |-->Screen "aticonfig-Screen[0]-0" (0)
[    15.742] (**) |   |-->Monitor "aticonfig-Monitor[0]-0"
[    15.743] (**) |   |-->Device "aticonfig-Device[0]-0"
[    15.743] (==) Automatically adding devices
[    15.743] (==) Automatically enabling devices
[    15.747] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[    15.747] 	Entry deleted from font path.
[    15.749] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[    15.749] 	Entry deleted from font path.
[    15.749] 	(Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[    15.750] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[    15.750] 	Entry deleted from font path.
[    15.750] 	(Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[    15.750] (==) FontPath set to:
	/usr/share/fonts/misc/,
	/usr/share/fonts/TTF/,
	/usr/share/fonts/Type1/
[    15.750] (==) ModulePath set to "/usr/lib/xorg/modules"
[    15.750] (II) The server relies on udev to provide the list of input devices.
	If no devices become available, reconfigure udev or disable AutoAddDevices.
[    15.750] (II) Loader magic: 0x7c7ae0
[    15.750] (II) Module ABI versions:
[    15.750] 	X.Org ANSI C Emulation: 0.4
[    15.750] 	X.Org Video Driver: 11.0
[    15.750] 	X.Org XInput driver : 13.0
[    15.750] 	X.Org Server Extension : 6.0
[    15.752] (--) PCI:*(0:1:0:0) 1002:9553:1028:02be rev 0, Mem @ 0xd0000000/268435456, 0xfc000000/65536, I/O @ 0x00002000/256, BIOS @ 0x????????/131072
[    15.752] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[    15.752] (II) "extmod" will be loaded by default.
[    15.752] (II) "dbe" will be loaded by default.
[    15.752] (II) "glx" will be loaded by default.
[    15.752] (II) "record" will be loaded by default.
[    15.752] (II) "dri" will be loaded by default.
[    15.752] (II) "dri2" will be loaded by default.
[    15.752] (II) LoadModule: "extmod"
[    15.753] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[    15.755] (II) Module extmod: vendor="X.Org Foundation"
[    15.755] 	compiled for 1.11.4, module version = 1.0.0
[    15.755] 	Module class: X.Org Server Extension
[    15.755] 	ABI class: X.Org Server Extension, version 6.0
[    15.755] (II) Loading extension MIT-SCREEN-SAVER
[    15.755] (II) Loading extension XFree86-VidModeExtension
[    15.755] (II) Loading extension XFree86-DGA
[    15.755] (II) Loading extension DPMS
[    15.755] (II) Loading extension XVideo
[    15.755] (II) Loading extension XVideo-MotionCompensation
[    15.755] (II) Loading extension X-Resource
[    15.755] (II) LoadModule: "dbe"
[    15.755] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[    15.755] (II) Module dbe: vendor="X.Org Foundation"
[    15.755] 	compiled for 1.11.4, module version = 1.0.0
[    15.755] 	Module class: X.Org Server Extension
[    15.755] 	ABI class: X.Org Server Extension, version 6.0
[    15.755] (II) Loading extension DOUBLE-BUFFER
[    15.755] (II) LoadModule: "glx"
[    15.756] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[    15.759] (II) Module glx: vendor="Advanced Micro Devices, Inc."
[    15.760] 	compiled for 6.9.0, module version = 1.0.0
[    15.760] (II) Loading extension GLX
[    15.760] (II) LoadModule: "record"
[    15.760] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[    15.761] (II) Module record: vendor="X.Org Foundation"
[    15.761] 	compiled for 1.11.4, module version = 1.13.0
[    15.761] 	Module class: X.Org Server Extension
[    15.761] 	ABI class: X.Org Server Extension, version 6.0
[    15.761] (II) Loading extension RECORD
[    15.761] (II) LoadModule: "dri"
[    15.761] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[    15.764] (II) Module dri: vendor="X.Org Foundation"
[    15.764] 	compiled for 1.11.4, module version = 1.0.0
[    15.764] 	ABI class: X.Org Server Extension, version 6.0
[    15.764] (II) Loading extension XFree86-DRI
[    15.764] (II) LoadModule: "dri2"
[    15.764] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[    15.765] (II) Module dri2: vendor="X.Org Foundation"
[    15.765] 	compiled for 1.11.4, module version = 1.2.0
[    15.765] 	ABI class: X.Org Server Extension, version 6.0
[    15.765] (II) Loading extension DRI2
[    15.765] (II) LoadModule: "fglrx"
[    15.765] (II) Loading /usr/lib/xorg/modules/drivers/fglrx_drv.so
[    15.826] (II) Module fglrx: vendor="FireGL - ATI Technologies Inc."
[    15.828] 	compiled for 1.4.99.906, module version = 8.96.4
[    15.828] 	Module class: X.Org Video Driver
[    15.829] (II) Loading sub module "fglrxdrm"
[    15.829] (II) LoadModule: "fglrxdrm"
[    15.829] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
[    15.832] (II) Module fglrxdrm: vendor="FireGL - ATI Technologies Inc."
[    15.832] 	compiled for 1.4.99.906, module version = 8.96.4
[    15.832] (II) ATI Proprietary Linux Driver Version Identifier:8.96.4
[    15.832] (II) ATI Proprietary Linux Driver Release Identifier: 8.961                                
[    15.832] (II) ATI Proprietary Linux Driver Build Date: Apr  5 2012 23:06:21
[    15.832] (++) using VT number 7

[    15.868] (WW) Falling back to old probe method for fglrx
[    15.883] (II) Loading PCS database from /etc/ati/amdpcsdb
[    15.886] (--) Chipset Supported AMD Graphics Processor (0x9553) found
[    15.887] (WW) fglrx: No matching Device section for instance (BusID PCI:0@1:0:1) found
[    15.888] (II) AMD Video driver is running on a device belonging to a group targeted for this release
[    15.888] (II) AMD Video driver is signed
[    15.888] (II) Loading /usr/lib/xorg/modules/drivers/fglrx_drv.so
[    15.888] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
[    15.888] (II) fglrx(0): pEnt->device->identifier=0x1fb8fc0
[    15.888] (II) fglrx(0): === [xdl_xs111_atiddxPreInit] === begin
[    15.888] (II) Loading sub module "vgahw"
[    15.888] (II) LoadModule: "vgahw"
[    15.888] (II) Loading /usr/lib/xorg/modules/libvgahw.so
[    15.889] (II) Module vgahw: vendor="X.Org Foundation"
[    15.889] 	compiled for 1.11.4, module version = 0.1.0
[    15.889] 	ABI class: X.Org Video Driver, version 11.0
[    15.889] (**) fglrx(0): Depth 24, (--) framebuffer bpp 32
[    15.889] (II) fglrx(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
[    15.889] (==) fglrx(0): Default visual is TrueColor
[    15.889] (**) fglrx(0): Option "DPMS" "true"
[    15.889] (==) fglrx(0): RGB weight 888
[    15.889] (II) fglrx(0): Using 8 bits per RGB 
[    15.889] (==) fglrx(0): Buffer Tiling is ON
[    15.890] (II) Loading sub module "fglrxdrm"
[    15.890] (II) LoadModule: "fglrxdrm"
[    15.890] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
[    15.890] (II) Module fglrxdrm: vendor="FireGL - ATI Technologies Inc."
[    15.890] 	compiled for 1.4.99.906, module version = 8.96.4
[    15.892] ukiDynamicMajor: found major device number 249
[    15.893] ukiDynamicMajor: found major device number 249
[    15.893] ukiOpenByBusid: Searching for BusID PCI:1:0:0
[    15.893] ukiOpenDevice: node name is /dev/ati/card0
[    15.893] ukiOpenDevice: open result is 11, (OK)
[    15.893] ukiOpenByBusid: ukiOpenMinor returns 11
[    15.893] ukiOpenByBusid: ukiGetBusid reports PCI:1:0:0
[    15.893] (**) fglrx(0): NoAccel = NO
[    15.893] (**) fglrx(0): ATI 2D Acceleration Architecture enabled
[    15.893] (--) fglrx(0): Chipset: "ATI Mobility Radeon HD 4500 Series" (Chipset = 0x9553)
[    15.893] (--) fglrx(0): (PciSubVendor = 0x1028, PciSubDevice = 0x02be)
[    15.893] (==) fglrx(0): board vendor info: third party graphics adapter - NOT original ATI
[    15.893] (--) fglrx(0): Linear framebuffer (phys) at 0xd0000000
[    15.893] (--) fglrx(0): MMIO registers at 0xfc000000
[    15.893] (--) fglrx(0): I/O port at 0x00002000
[    15.893] (==) fglrx(0): ROM-BIOS at 0x000c0000
[    16.090] (II) fglrx(0): AC Adapter is used
[    16.104] (II) fglrx(0): Primary V_BIOS segment is: 0xc000
[    16.105] (II) Loading sub module "vbe"
[    16.105] (II) LoadModule: "vbe"
[    16.106] (II) Loading /usr/lib/xorg/modules/libvbe.so
[    16.107] (II) Module vbe: vendor="X.Org Foundation"
[    16.107] 	compiled for 1.11.4, module version = 1.1.0
[    16.107] 	ABI class: X.Org Video Driver, version 11.0
[    16.107] (II) fglrx(0): VESA BIOS detected
[    16.107] (II) fglrx(0): VESA VBE Version 3.0
[    16.107] (II) fglrx(0): VESA VBE Total Mem: 16384 kB
[    16.107] (II) fglrx(0): VESA VBE OEM: ATI ATOMBIOS
[    16.107] (II) fglrx(0): VESA VBE OEM Software Rev: 11.21
[    16.107] (II) fglrx(0): VESA VBE OEM Vendor: (C) 1988-2005, ATI Technologies Inc. 
[    16.107] (II) fglrx(0): VESA VBE OEM Product: M92
[    16.107] (II) fglrx(0): VESA VBE OEM Product Rev: 01.00
[    16.146] (II) fglrx(0): ATI Video BIOS revision 9 or later detected
[    16.146] (--) fglrx(0): Video RAM: 524288 kByte, Type: GDDR3
[    16.146] (II) fglrx(0): PCIE card detected
[    16.146] (--) fglrx(0): Using per-process page tables (PPPT) as GART.
[    16.146] (WW) fglrx(0): board is an unknown third party board, chipset is supported
[    16.151] (II) fglrx(0): Using adapter: 1:0.0.
[    16.179] (II) fglrx(0): [FB] MC range(MCFBBase = 0xf00000000, MCFBSize = 0x20000000)
[    16.204] (II) fglrx(0): Interrupt handler installed at IRQ 50.
[    16.204] (II) fglrx(0): RandR 1.2 support is enabled!
[    16.204] (II) fglrx(0): RandR 1.2 rotation support is enabled!
[    16.204] (==) fglrx(0): Center Mode is disabled 
[    16.204] (II) Loading sub module "fb"
[    16.204] (II) LoadModule: "fb"
[    16.205] (II) Loading /usr/lib/xorg/modules/libfb.so
[    16.207] (II) Module fb: vendor="X.Org Foundation"
[    16.207] 	compiled for 1.11.4, module version = 1.0.0
[    16.207] 	ABI class: X.Org ANSI C Emulation, version 0.4
[    16.207] (II) Loading sub module "ddc"
[    16.207] (II) LoadModule: "ddc"
[    16.207] (II) Module "ddc" already built-in
[    16.399] (II) fglrx(0): Finished Initialize PPLIB!
[    16.405] (II) fglrx(0): Output LVDS using monitor section aticonfig-Monitor[0]-0
[    16.405] (II) fglrx(0): Output DFP1 has no monitor section
[    16.405] (II) fglrx(0): Output CRT1 has no monitor section
[    16.405] (II) Loading sub module "ddc"
[    16.405] (II) LoadModule: "ddc"
[    16.405] (II) Module "ddc" already built-in
[    16.405] (II) fglrx(0): Connected Display0: LVDS
[    16.405] (II) fglrx(0): Display0 EDID data ---------------------------
[    16.405] (II) fglrx(0): Manufacturer: SEC  Model: 5441  Serial#: 0
[    16.405] (II) fglrx(0): Year: 2008  Week: 0
[    16.405] (II) fglrx(0): EDID Version: 1.3
[    16.405] (II) fglrx(0): Digital Display Input
[    16.405] (II) fglrx(0): Max Image Size [cm]: horiz.: 34  vert.: 19
[    16.405] (II) fglrx(0): Gamma: 2.20
[    16.405] (II) fglrx(0): No DPMS capabilities specified
[    16.405] (II) fglrx(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 
[    16.405] (II) fglrx(0): First detailed timing is preferred mode
[    16.405] (II) fglrx(0): redX: 0.580 redY: 0.340   greenX: 0.310 greenY: 0.550
[    16.405] (II) fglrx(0): blueX: 0.155 blueY: 0.155   whiteX: 0.313 whiteY: 0.329
[    16.405] (II) fglrx(0): Manufacturer's mask: 0
[    16.405] (II) fglrx(0): Supported detailed timing:
[    16.405] (II) fglrx(0): clock: 72.3 MHz   Image Size:  353 x 198 mm
[    16.405] (II) fglrx(0): h_active: 1366  h_sync: 1414  h_sync_end 1446 h_blank_end 1526 h_border: 0
[    16.405] (II) fglrx(0): v_active: 768  v_sync: 770  v_sync_end 775 v_blanking: 790 v_border: 0
[    16.405] (II) fglrx(0): Supported detailed timing:
[    16.405] (II) fglrx(0): clock: 72.3 MHz   Image Size:  344 x 194 mm
[    16.405] (II) fglrx(0): h_active: 1366  h_sync: 1414  h_sync_end 1446 h_blank_end 1526 h_border: 0
[    16.405] (II) fglrx(0): v_active: 768  v_sync: 770  v_sync_end 775 v_blanking: 790 v_border: 0
[    16.405] (II) fglrx(0):  C970J€156AT
[    16.405] (II) fglrx(0): Unknown vendor-specific block 0
[    16.405] (II) fglrx(0): EDID (in hex):
[    16.405] (II) fglrx(0): 	00ffffffffffff004ca3415400000000
[    16.405] (II) fglrx(0): 	00120103902213780a87f594574f8c27
[    16.405] (II) fglrx(0): 	27505400000001010101010101010101
[    16.405] (II) fglrx(0): 	010101010101411c56a0500016303020
[    16.405] (II) fglrx(0): 	250061c61000001a411c56a050001630
[    16.405] (II) fglrx(0): 	3020250058c21000001a000000fe0043
[    16.405] (II) fglrx(0): 	3937304a8031353641540a2000000000
[    16.405] (II) fglrx(0): 	00000000000000000001010a2020003e
[    16.405] (II) fglrx(0): End of Display0 EDID data --------------------
[    16.438] (II) fglrx(0): EDID for output LVDS
[    16.438] (II) fglrx(0): Manufacturer: SEC  Model: 5441  Serial#: 0
[    16.438] (II) fglrx(0): Year: 2008  Week: 0
[    16.438] (II) fglrx(0): EDID Version: 1.3
[    16.438] (II) fglrx(0): Digital Display Input
[    16.438] (II) fglrx(0): Max Image Size [cm]: horiz.: 34  vert.: 19
[    16.438] (II) fglrx(0): Gamma: 2.20
[    16.438] (II) fglrx(0): No DPMS capabilities specified
[    16.438] (II) fglrx(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 
[    16.438] (II) fglrx(0): First detailed timing is preferred mode
[    16.438] (II) fglrx(0): redX: 0.580 redY: 0.340   greenX: 0.310 greenY: 0.550
[    16.438] (II) fglrx(0): blueX: 0.155 blueY: 0.155   whiteX: 0.313 whiteY: 0.329
[    16.438] (II) fglrx(0): Manufacturer's mask: 0
[    16.438] (II) fglrx(0): Supported detailed timing:
[    16.438] (II) fglrx(0): clock: 72.3 MHz   Image Size:  353 x 198 mm
[    16.438] (II) fglrx(0): h_active: 1366  h_sync: 1414  h_sync_end 1446 h_blank_end 1526 h_border: 0
[    16.438] (II) fglrx(0): v_active: 768  v_sync: 770  v_sync_end 775 v_blanking: 790 v_border: 0
[    16.438] (II) fglrx(0): Supported detailed timing:
[    16.438] (II) fglrx(0): clock: 72.3 MHz   Image Size:  344 x 194 mm
[    16.438] (II) fglrx(0): h_active: 1366  h_sync: 1414  h_sync_end 1446 h_blank_end 1526 h_border: 0
[    16.438] (II) fglrx(0): v_active: 768  v_sync: 770  v_sync_end 775 v_blanking: 790 v_border: 0
[    16.438] (II) fglrx(0):  C970J€156AT
[    16.438] (II) fglrx(0): Unknown vendor-specific block 0
[    16.438] (II) fglrx(0): EDID (in hex):
[    16.438] (II) fglrx(0): 	00ffffffffffff004ca3415400000000
[    16.438] (II) fglrx(0): 	00120103902213780a87f594574f8c27
[    16.438] (II) fglrx(0): 	27505400000001010101010101010101
[    16.438] (II) fglrx(0): 	010101010101411c56a0500016303020
[    16.438] (II) fglrx(0): 	250061c61000001a411c56a050001630
[    16.438] (II) fglrx(0): 	3020250058c21000001a000000fe0043
[    16.438] (II) fglrx(0): 	3937304a8031353641540a2000000000
[    16.438] (II) fglrx(0): 	00000000000000000001010a2020003e
[    16.438] (II) fglrx(0): EDID vendor "SEC", prod id 21569
[    16.438] (II) fglrx(0): Printing DDC gathered Modelines:
[    16.438] (II) fglrx(0): Modeline "1366x768"x0.0   72.33  1366 1414 1446 1526  768 770 775 790 +hsync -vsync (47.4 kHz)
[    16.438] (II) fglrx(0): Printing probed modes for output LVDS
[    16.439] (II) fglrx(0): Modeline "1366x768"x60.0   72.33  1366 1414 1446 1526  768 770 775 790 -hsync +vsync (47.4 kHz)
[    16.439] (II) fglrx(0): Modeline "1280x768"x60.0   72.33  1280 1414 1446 1526  768 770 775 790 -hsync +vsync (47.4 kHz)
[    16.439] (II) fglrx(0): Modeline "1280x720"x60.0   72.33  1280 1414 1446 1526  720 770 775 790 -hsync +vsync (47.4 kHz)
[    16.439] (II) fglrx(0): Modeline "1024x768"x60.0   72.33  1024 1414 1446 1526  768 770 775 790 -hsync +vsync (47.4 kHz)
[    16.439] (II) fglrx(0): Modeline "1024x600"x60.0   72.33  1024 1414 1446 1526  600 770 775 790 -hsync +vsync (47.4 kHz)
[    16.439] (II) fglrx(0): Modeline "800x600"x60.0   72.33  800 1414 1446 1526  600 770 775 790 -hsync +vsync (47.4 kHz)
[    16.439] (II) fglrx(0): Modeline "800x480"x60.0   72.33  800 1414 1446 1526  480 770 775 790 -hsync +vsync (47.4 kHz)
[    16.439] (II) fglrx(0): Modeline "720x480"x60.0   72.33  720 1414 1446 1526  480 770 775 790 -hsync +vsync (47.4 kHz)
[    16.439] (II) fglrx(0): Modeline "640x480"x60.0   72.33  640 1414 1446 1526  480 770 775 790 -hsync +vsync (47.4 kHz)
[    16.439] (II) fglrx(0): EDID for output DFP1
[    16.439] (II) fglrx(0): EDID for output CRT1
[    16.439] (II) fglrx(0): Output LVDS connected
[    16.439] (II) fglrx(0): Output DFP1 disconnected
[    16.439] (II) fglrx(0): Output CRT1 disconnected
[    16.439] (II) fglrx(0): Using exact sizes for initial modes
[    16.439] (II) fglrx(0): Output LVDS using initial mode 1366x768
[    16.439] (II) fglrx(0): Display dimensions: (340, 190) mm
[    16.439] (II) fglrx(0): DPI set to (102, 102)
[    16.439] (II) fglrx(0): Adapter ATI Mobility Radeon HD 4500 Series has 2 configurable heads and 1 displays connected.
[    16.439] (==) fglrx(0):  PseudoColor visuals disabled
[    16.439] (II) Loading sub module "ramdac"
[    16.439] (II) LoadModule: "ramdac"
[    16.439] (II) Module "ramdac" already built-in
[    16.439] (==) fglrx(0): NoDRI = NO
[    16.439] (==) fglrx(0): Capabilities: 0x00000000
[    16.439] (==) fglrx(0): CapabilitiesEx: 0x00000000
[    16.439] (==) fglrx(0): OpenGL ClientDriverName: "fglrx_dri.so"
[    16.439] (==) fglrx(0): UseFastTLS=0
[    16.439] (--) Depth 24 pixmap format is 32 bpp
[    16.439] (II) Loading extension ATIFGLRXDRI
[    16.439] (II) fglrx(0): doing swlDriScreenInit
[    16.439] (II) fglrx(0): swlDriScreenInit for fglrx driver
[    16.439] ukiDynamicMajor: found major device number 249
[    16.439] ukiDynamicMajor: found major device number 249
[    16.439] ukiDynamicMajor: found major device number 249
[    16.439] ukiOpenByBusid: Searching for BusID PCI:1:0:0
[    16.439] ukiOpenDevice: node name is /dev/ati/card0
[    16.439] ukiOpenDevice: open result is 16, (OK)
[    16.439] ukiOpenByBusid: ukiOpenMinor returns 16
[    16.439] ukiOpenByBusid: ukiGetBusid reports PCI:1:0:0
[    16.439] (II) fglrx(0): [uki] DRM interface version 1.0
[    16.439] (II) fglrx(0): [uki] created "fglrx" driver at busid "PCI:1:0:0"
[    16.439] (II) fglrx(0): [uki] added 8192 byte SAREA at 0x2000
[    16.439] (II) fglrx(0): [uki] mapped SAREA 0x2000 to 0x7f6315e83000
[    16.439] (II) fglrx(0): [uki] framebuffer handle = 0x3000
[    16.439] (II) fglrx(0): [uki] added 1 reserved context for kernel
[    16.439] (II) fglrx(0): swlDriScreenInit done
[    16.439] (II) fglrx(0): Kernel Module Version Information:
[    16.439] (II) fglrx(0):     Name: fglrx
[    16.439] (II) fglrx(0):     Version: 8.96.4
[    16.439] (II) fglrx(0):     Date: Apr  5 2012
[    16.439] (II) fglrx(0):     Desc: ATI FireGL DRM kernel module
[    16.440] (II) fglrx(0): Kernel Module version matches driver.
[    16.440] (II) fglrx(0): Kernel Module Build Time Information:
[    16.440] (II) fglrx(0):     Build-Kernel UTS_RELEASE:        3.0.36-2-lts
[    16.440] (II) fglrx(0):     Build-Kernel MODVERSIONS:        no
[    16.440] (II) fglrx(0):     Build-Kernel __SMP__:            no
[    16.440] (II) fglrx(0):     Build-Kernel PAGE_SIZE:          0x1000
[    16.440] (II) fglrx(0): [uki] register handle = 0x00004000
[    16.464] (II) fglrx(0): DRI initialization successfull
[    16.465] (II) fglrx(0): FBADPhys: 0xf00000000 FBMappedSize: 0x01004000
[    16.467] (==) fglrx(0): Backing store disabled
[    16.467] (II) Loading extension FGLRXEXTENSION
[    16.467] (**) fglrx(0): DPMS enabled
[    16.467] (II) fglrx(0): Initialized in-driver Xinerama extension
[    16.467] (**) fglrx(0): Textured Video is enabled.
[    16.467] (II) LoadModule: "glesx"
[    16.468] (II) Loading /usr/lib/xorg/modules/glesx.so
[    16.494] (II) Module glesx: vendor="X.Org Foundation"
[    16.494] 	compiled for 1.4.99.906, module version = 1.0.0
[    16.494] (II) Loading extension GLESX
[    16.494] (II) fglrx(0): GLESX enableFlags = 528
[    16.495] (II) fglrx(0): GLESX is enabled
[    16.495] (II) LoadModule: "amdxmm"
[    16.495] (II) Loading /usr/lib/xorg/modules/amdxmm.so
[    16.498] (II) Module amdxmm: vendor="X.Org Foundation"
[    16.499] 	compiled for 1.4.99.906, module version = 2.0.0
[    16.499] (II) Loading extension AMDXVOPL
[    16.499] (II) Loading extension AMDXVBA
[    16.505] (II) fglrx(0): UVD feature is enabled(II) fglrx(0): 
[    16.513] (II) fglrx(0): Enable composite support successfully
[    16.513] (WW) fglrx(0): Option "VendorName" is not used
[    16.513] (WW) fglrx(0): Option "ModelName" is not used
[    16.513] (II) fglrx(0): X context handle = 0x1
[    16.514] (II) fglrx(0): [DRI] installation complete
[    16.514] (==) fglrx(0): Silken mouse enabled
[    16.514] (==) fglrx(0): Using HW cursor of display infrastructure!
[    16.515] (II) fglrx(0): Disabling in-server RandR and enabling in-driver RandR 1.2.
[    16.515] (II) fglrx(0): 'LVDS LCD' ConnectorType, abstracted as 'Panel'
[    16.515] (II) fglrx(0): 'eDP LCD' ConnectorType, abstracted as 'Panel'
[    17.547] (--) RandR disabled
[    17.547] (II) Initializing built-in extension Generic Event Extension
[    17.547] (II) Initializing built-in extension SHAPE
[    17.547] (II) Initializing built-in extension MIT-SHM
[    17.547] (II) Initializing built-in extension XInputExtension
[    17.547] (II) Initializing built-in extension XTEST
[    17.547] (II) Initializing built-in extension BIG-REQUESTS
[    17.547] (II) Initializing built-in extension SYNC
[    17.547] (II) Initializing built-in extension XKEYBOARD
[    17.547] (II) Initializing built-in extension XC-MISC
[    17.547] (II) Initializing built-in extension SECURITY
[    17.547] (II) Initializing built-in extension XINERAMA
[    17.547] (II) Initializing built-in extension XFIXES
[    17.547] (II) Initializing built-in extension RENDER
[    17.547] (II) Initializing built-in extension RANDR
[    17.547] (II) Initializing built-in extension COMPOSITE
[    17.547] (II) Initializing built-in extension DAMAGE
[    17.549] ukiDynamicMajor: found major device number 249
[    17.549] ukiDynamicMajor: found major device number 249
[    17.549] ukiOpenByBusid: Searching for BusID PCI:1:0:0
[    17.549] ukiOpenDevice: node name is /dev/ati/card0
[    17.549] ukiOpenDevice: open result is 17, (OK)
[    17.549] ukiOpenByBusid: ukiOpenMinor returns 17
[    17.549] ukiOpenByBusid: ukiGetBusid reports PCI:1:0:0
[    17.830] (II) AIGLX: Loaded and initialized OpenGL driver(II) GLX: Initialized DRI GL provider for screen 0
[    17.861] (II) fglrx(0): Enable the clock gating!
[    17.861] (II) fglrx(0): Setting screen physical size to 361 x 203
[    18.006] (II) config/udev: Adding input device Power Button (/dev/input/event7)
[    18.006] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    18.006] (II) LoadModule: "evdev"
[    18.006] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    18.007] (II) Module evdev: vendor="X.Org Foundation"
[    18.007] 	compiled for 1.10.99.902, module version = 2.6.0
[    18.007] 	Module class: X.Org XInput Driver
[    18.007] 	ABI class: X.Org XInput driver, version 13.0
[    18.007] (II) Using input driver 'evdev' for 'Power Button'
[    18.007] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    18.008] (**) Power Button: always reports core events
[    18.008] (**) Power Button: Device: "/dev/input/event7"
[    18.008] (--) Power Button: Found keys
[    18.008] (II) Power Button: Configuring as keyboard
[    18.008] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input7/event7"
[    18.008] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[    18.008] (**) Option "xkb_rules" "evdev"
[    18.008] (**) Option "xkb_model" "evdev"
[    18.008] (**) Option "xkb_layout" "us"
[    18.043] (II) config/udev: Adding input device Video Bus (/dev/input/event8)
[    18.043] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[    18.043] (II) Using input driver 'evdev' for 'Video Bus'
[    18.043] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    18.043] (**) Video Bus: always reports core events
[    18.043] (**) Video Bus: Device: "/dev/input/event8"
[    18.043] (--) Video Bus: Found keys
[    18.043] (II) Video Bus: Configuring as keyboard
[    18.043] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input8/event8"
[    18.043] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[    18.043] (**) Option "xkb_rules" "evdev"
[    18.043] (**) Option "xkb_model" "evdev"
[    18.043] (**) Option "xkb_layout" "us"
[    18.043] (II) config/udev: Adding input device Power Button (/dev/input/event4)
[    18.043] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    18.043] (II) Using input driver 'evdev' for 'Power Button'
[    18.043] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    18.043] (**) Power Button: always reports core events
[    18.043] (**) Power Button: Device: "/dev/input/event4"
[    18.043] (--) Power Button: Found keys
[    18.043] (II) Power Button: Configuring as keyboard
[    18.043] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4/event4"
[    18.043] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[    18.043] (**) Option "xkb_rules" "evdev"
[    18.043] (**) Option "xkb_model" "evdev"
[    18.043] (**) Option "xkb_layout" "us"
[    18.044] (II) config/udev: Adding input device Lid Switch (/dev/input/event6)
[    18.044] (II) No input driver specified, ignoring this device.
[    18.044] (II) This device may have been added with another device file.
[    18.044] (II) config/udev: Adding input device Sleep Button (/dev/input/event5)
[    18.044] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[    18.044] (II) Using input driver 'evdev' for 'Sleep Button'
[    18.044] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    18.044] (**) Sleep Button: always reports core events
[    18.044] (**) Sleep Button: Device: "/dev/input/event5"
[    18.044] (--) Sleep Button: Found keys
[    18.044] (II) Sleep Button: Configuring as keyboard
[    18.044] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input5/event5"
[    18.044] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 9)
[    18.044] (**) Option "xkb_rules" "evdev"
[    18.044] (**) Option "xkb_model" "evdev"
[    18.044] (**) Option "xkb_layout" "us"
[    18.044] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP (/dev/input/event13)
[    18.044] (II) No input driver specified, ignoring this device.
[    18.044] (II) This device may have been added with another device file.
[    18.045] (II) config/udev: Adding input device HID 413c:8157 (/dev/input/event2)
[    18.045] (**) HID 413c:8157: Applying InputClass "evdev keyboard catchall"
[    18.045] (II) Using input driver 'evdev' for 'HID 413c:8157'
[    18.045] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    18.045] (**) HID 413c:8157: always reports core events
[    18.045] (**) HID 413c:8157: Device: "/dev/input/event2"
[    18.045] (--) HID 413c:8157: Found keys
[    18.045] (II) HID 413c:8157: Configuring as keyboard
[    18.045] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.1/3-1.1:1.0/input/input2/event2"
[    18.045] (II) XINPUT: Adding extended input device "HID 413c:8157" (type: KEYBOARD, id 10)
[    18.045] (**) Option "xkb_rules" "evdev"
[    18.045] (**) Option "xkb_model" "evdev"
[    18.045] (**) Option "xkb_layout" "us"
[    18.045] (II) config/udev: Adding input device Laptop_Integrated_Webcam_2M (/dev/input/event9)
[    18.045] (**) Laptop_Integrated_Webcam_2M: Applying InputClass "evdev keyboard catchall"
[    18.045] (II) Using input driver 'evdev' for 'Laptop_Integrated_Webcam_2M'
[    18.045] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    18.045] (**) Laptop_Integrated_Webcam_2M: always reports core events
[    18.045] (**) Laptop_Integrated_Webcam_2M: Device: "/dev/input/event9"
[    18.045] (--) Laptop_Integrated_Webcam_2M: Found keys
[    18.045] (II) Laptop_Integrated_Webcam_2M: Configuring as keyboard
[    18.045] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.7/usb1/1-6/1-6:1.0/input/input9/event9"
[    18.045] (II) XINPUT: Adding extended input device "Laptop_Integrated_Webcam_2M" (type: KEYBOARD, id 11)
[    18.045] (**) Option "xkb_rules" "evdev"
[    18.045] (**) Option "xkb_model" "evdev"
[    18.045] (**) Option "xkb_layout" "us"
[    18.046] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event3)
[    18.046] (II) No input driver specified, ignoring this device.
[    18.046] (II) This device may have been added with another device file.
[    18.046] (II) config/udev: Adding input device HDA Intel Mic at Ext Left Jack (/dev/input/event10)
[    18.046] (II) No input driver specified, ignoring this device.
[    18.046] (II) This device may have been added with another device file.
[    18.046] (II) config/udev: Adding input device HDA Intel HP Out at Ext Left Jack (/dev/input/event11)
[    18.046] (II) No input driver specified, ignoring this device.
[    18.046] (II) This device may have been added with another device file.
[    18.046] (II) config/udev: Adding input device HDA Intel HP Out at Ext Left Jack (/dev/input/event12)
[    18.046] (II) No input driver specified, ignoring this device.
[    18.046] (II) This device may have been added with another device file.
[    18.047] (II) config/udev: Adding input device DELL DELL USB Laser Mouse (/dev/input/event1)
[    18.047] (**) DELL DELL USB Laser Mouse: Applying InputClass "evdev pointer catchall"
[    18.047] (II) Using input driver 'evdev' for 'DELL DELL USB Laser Mouse'
[    18.047] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    18.047] (**) DELL DELL USB Laser Mouse: always reports core events
[    18.047] (**) DELL DELL USB Laser Mouse: Device: "/dev/input/event1"
[    18.047] (--) DELL DELL USB Laser Mouse: Found 12 mouse buttons
[    18.047] (--) DELL DELL USB Laser Mouse: Found scroll wheel(s)
[    18.047] (--) DELL DELL USB Laser Mouse: Found relative axes
[    18.047] (--) DELL DELL USB Laser Mouse: Found x and y relative axes
[    18.047] (II) DELL DELL USB Laser Mouse: Configuring as mouse
[    18.047] (II) DELL DELL USB Laser Mouse: Adding scrollwheel support
[    18.047] (**) DELL DELL USB Laser Mouse: YAxisMapping: buttons 4 and 5
[    18.047] (**) DELL DELL USB Laser Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    18.047] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.0/input/input1/event1"
[    18.047] (II) XINPUT: Adding extended input device "DELL DELL USB Laser Mouse" (type: MOUSE, id 12)
[    18.047] (II) DELL DELL USB Laser Mouse: initialized for relative axes.
[    18.047] (**) DELL DELL USB Laser Mouse: (accel) keeping acceleration scheme 1
[    18.047] (**) DELL DELL USB Laser Mouse: (accel) acceleration profile 0
[    18.047] (**) DELL DELL USB Laser Mouse: (accel) acceleration factor: 2.000
[    18.047] (**) DELL DELL USB Laser Mouse: (accel) acceleration threshold: 4
[    18.047] (II) config/udev: Adding input device DELL DELL USB Laser Mouse (/dev/input/mouse0)
[    18.047] (II) No input driver specified, ignoring this device.
[    18.047] (II) This device may have been added with another device file.
[    18.048] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[    18.048] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[    18.048] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[    18.048] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    18.048] (**) AT Translated Set 2 keyboard: always reports core events
[    18.048] (**) AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[    18.048] (--) AT Translated Set 2 keyboard: Found keys
[    18.048] (II) AT Translated Set 2 keyboard: Configuring as keyboard
[    18.048] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[    18.048] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 13)
[    18.048] (**) Option "xkb_rules" "evdev"
[    18.048] (**) Option "xkb_model" "evdev"
[    18.048] (**) Option "xkb_layout" "us"
[    18.048] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event15)
[    18.048] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "evdev touchpad catchall"
[    18.048] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "touchpad catchall"
[    18.048] (II) LoadModule: "synaptics"
[    18.048] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[    18.049] (II) Module synaptics: vendor="X.Org Foundation"
[    18.049] 	compiled for 1.11.0, module version = 1.5.0
[    18.049] 	Module class: X.Org XInput Driver
[    18.050] 	ABI class: X.Org XInput driver, version 13.0
[    18.050] (II) Using input driver 'synaptics' for 'SynPS/2 Synaptics TouchPad'
[    18.050] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[    18.050] (**) SynPS/2 Synaptics TouchPad: always reports core events
[    18.050] (**) Option "Device" "/dev/input/event15"
[    18.690] (--) synaptics: SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5836
[    18.690] (--) synaptics: SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4908
[    18.690] (--) synaptics: SynPS/2 Synaptics TouchPad: pressure range 0 - 255
[    18.690] (--) synaptics: SynPS/2 Synaptics TouchPad: finger width range 0 - 0
[    18.690] (--) synaptics: SynPS/2 Synaptics TouchPad: buttons: left right double triple
[    18.690] (--) synaptics: SynPS/2 Synaptics TouchPad: Vendor 0x2 Product 0x7
[    18.690] (**) Option "TapButton1" "1"
[    18.690] (**) Option "TapButton2" "2"
[    18.690] (**) Option "TapButton3" "3"
[    19.010] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[    19.010] (**) SynPS/2 Synaptics TouchPad: always reports core events
[    19.330] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input16/event15"
[    19.330] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD, id 14)
[    19.330] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) MinSpeed is now constant deceleration 2.5
[    19.330] (**) synaptics: SynPS/2 Synaptics TouchPad: MaxSpeed is now 1.75
[    19.330] (**) synaptics: SynPS/2 Synaptics TouchPad: AccelFactor is now 0.036
[    19.331] (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
[    19.331] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 1
[    19.331] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[    19.331] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[    19.331] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[    19.332] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse1)
[    19.332] (II) No input driver specified, ignoring this device.
[    19.332] (II) This device may have been added with another device file.
[    19.333] (II) config/udev: Adding input device Dell WMI hotkeys (/dev/input/event14)
[    19.333] (**) Dell WMI hotkeys: Applying InputClass "evdev keyboard catchall"
[    19.333] (II) Using input driver 'evdev' for 'Dell WMI hotkeys'
[    19.333] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    19.334] (**) Dell WMI hotkeys: always reports core events
[    19.334] (**) Dell WMI hotkeys: Device: "/dev/input/event14"
[    19.334] (--) Dell WMI hotkeys: Found keys
[    19.334] (II) Dell WMI hotkeys: Configuring as keyboard
[    19.334] (**) Option "config_info" "udev:/sys/devices/virtual/input/input15/event14"
[    19.334] (II) XINPUT: Adding extended input device "Dell WMI hotkeys" (type: KEYBOARD, id 15)
[    19.334] (**) Option "xkb_rules" "evdev"
[    19.334] (**) Option "xkb_model" "evdev"
[    19.334] (**) Option "xkb_layout" "us"
[    19.814] (II) fglrx(0): Restoring Recent Mode via PCS is not supported in RANDR 1.2 capable environments
[    26.060] (II) AIGLX: Suspending AIGLX clients for VT switch
[    26.060] (II) fglrx(0): Backup framebuffer data.
[    26.069] (II) fglrx(0): Backup complete.
[   101.969] (II) AIGLX: Resuming AIGLX clients after VT switch
[   103.524] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[   109.147] (II) fglrx(0): EDID vendor "SEC", prod id 21569
[   109.147] (II) fglrx(0): Printing DDC gathered Modelines:
[   109.147] (II) fglrx(0): Modeline "1366x768"x0.0   72.33  1366 1414 1446 1526  768 770 775 790 +hsync -vsync (47.4 kHz)
[   116.050] (II) AIGLX: Suspending AIGLX clients for VT switch
[   116.050] (II) fglrx(0): Backup framebuffer data.
[   116.059] (II) fglrx(0): Backup complete.
[   135.166] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found

And after the update the reboot command started showing (just an extra info)

WARNING: could not determine runlevel - doing a soft reboot
(it's better to use shutdown instead of reboot from the command line)

Offline

#16 2012-07-22 09:07:38

bricklin
Member
Registered: 2010-07-26
Posts: 4

Re: GDM and Gnome not working, showing only the cursor and wallpaper

i have the exactly the same issue .. it seems no solution made...wait

Offline

#17 2012-08-22 16:08:19

Garr
Member
From: Poland
Registered: 2010-03-12
Posts: 20

Re: GDM and Gnome not working, showing only the cursor and wallpaper

similar problem here with both GDM and KDM when using nvidia proprietary drivers, everything works fine with nouveau driver

Offline

#18 2012-08-24 13:04:20

mellofone
Member
Registered: 2009-03-13
Posts: 37

Re: GDM and Gnome not working, showing only the cursor and wallpaper

I seem to have the same problem. But I am not using anything nVidia, I have a Radeon HD 4250. System boots fine, no errors. I however, don't boot to the login screen, I am using GDM. System boots, then the screen goes black. I can move the mouse around, but that's where it ends.

Offline

#19 2012-08-24 14:59:53

\〠/
Member
Registered: 2011-02-26
Posts: 29

Re: GDM and Gnome not working, showing only the cursor and wallpaper

Randomly similar problem here too, Radeon HD 4250. Forced me to try unity and surprisingly it works fine so far.

Offline

#20 2012-08-25 01:14:59

mozzcol
Member
Registered: 2012-08-25
Posts: 1

Re: GDM and Gnome not working, showing only the cursor and wallpaper

I think you should look here: https://bugs.archlinux.org/task/30476

I just solved a -> similar <- problem running dbus-uuidgen > /etc/machine-id as described there.
In my case /etc/machine-id was empty, both (GDM and Gnome) crashes on login and I was getting the following error: "Message did not receive a reply (timeout by message bus)"

Offline

#21 2012-08-27 12:46:49

mellofone
Member
Registered: 2009-03-13
Posts: 37

Re: GDM and Gnome not working, showing only the cursor and wallpaper

That made no difference for me. /etc/machine-id already existed and regenerating it made no difference.

Offline

#22 2012-08-27 13:47:44

Darkzom
Member
Registered: 2011-03-15
Posts: 28

Re: GDM and Gnome not working, showing only the cursor and wallpaper

Hi!

Something similar is happening to me lately since my last big update wich is 1 week ago. I went off on holidays for 3 weeks and when I returned I had a lot of packages to update.

The error is similar, gnome shell tries to start but I only get to see wallpaper and mouse cursor (movable), however the top side of the shell is blocked and no action can be done by clicking anywhere. I have also noticed that loads almost everything but the network indicator is in red, as if it had no network, however network is present and configured but it just locks right before changing network icon to OK.

I am currently at work so I can not paste logs but I have not seen any error on my logs so far. I thought it would happen when cold booting but sometimes the error is not fixed when forcing reboot from terminal.

The only solution I found is to manually switch to terminal and force stop and restart on GDM. ("sudo /etc/rc.d/gdm stop" and then "sudo /etc/rc.d/gdm start") and then everything works as expected.

It does not happen always... I would say about 50%.

Any guess on what did change or what do we have incorrectly configured?? My machine ID is also good.

Thanks and best regards,

Last edited by Darkzom (2012-08-27 13:49:33)

Offline

#23 2012-09-05 18:20:34

luvfree
Member
Registered: 2012-08-29
Posts: 81

Re: GDM and Gnome not working, showing only the cursor and wallpaper

mcapu wrote:

Well, I read somewhere that this could be happening due to having created the user before installing gnome, but I made another user for testing and the same problem occurs.

This worked for me but only after creating the new user by the command line using adduser.
Creating the new user via another desktop environment failed.


Linux only since 2002! Arch Linux only since 2010!
UEFI booting an intel based system trouble free since 2016!

Offline

#24 2012-09-07 21:50:23

jkain
Member
Registered: 2012-09-07
Posts: 1

Re: GDM and Gnome not working, showing only the cursor and wallpaper

I just experienced the same problem after an upgrade.  I found that the error (well, mine was in english but I think it's the same problem):

     '"Error invoking Gio.bus_get_sync: No se pudo conectar: No existe el fichero o el directorio"'

Refered to the file /var/run/dbus/system_bus_socket.  However, it seemed that /var/run had been moved to /run after the upgrade!  I removed /var/run and created a symlink from /var/run to /run and gnome starts up for me now.  I hope it works for you too.

Offline

#25 2012-09-10 02:32:48

AustinC
Member
From: Wash DC
Registered: 2012-01-22
Posts: 7

Re: GDM and Gnome not working, showing only the cursor and wallpaper

I was receiving the same log error referring to "Gio.bus_get_sync" after a system upgrade. As part of the upgrade my new /etc/rc.conf file did not include the dbus daemon. Adding dbus back to the rc.conf resolved the issue for me.

Offline

Board footer

Powered by FluxBB