You are not logged in.

#1 2012-08-27 18:42:32

DexterLB
Member
Registered: 2011-06-20
Posts: 51

[SOLVED] Trayer position

Is there a way to position Trayer at arbitrary x/y coordinates? I only seem to be able to set the screen edge, but not the position

Last edited by DexterLB (2012-08-30 05:49:14)


The best solution to a problem is usually the easiest one.

Offline

#2 2012-08-27 18:59:53

bgc1954
Member
From: Edmonton, AB, Canada
Registered: 2006-03-14
Posts: 1,160

Re: [SOLVED] Trayer position

Not really as far as I've ever been able to figure out the manpage.  You can pick an --edge and then --distance from the edge for the tray but thats about all.


Time is a great teacher, but unfortunately it kills all its pupils ... - Louis Hector Berlioz

Offline

#3 2012-08-28 06:23:58

DexterLB
Member
Registered: 2011-06-20
Posts: 51

Re: [SOLVED] Trayer position

bgc1954 wrote:

Not really as far as I've ever been able to figure out the manpage.  You can pick an --edge and then --distance from the edge for the tray but thats about all.

That's a shame.. is there any similar app with this feature?


The best solution to a problem is usually the easiest one.

Offline

#4 2012-08-28 17:50:25

bgc1954
Member
From: Edmonton, AB, Canada
Registered: 2006-03-14
Posts: 1,160

Re: [SOLVED] Trayer position

I believe stalonetray has a geometry setting but I haven't used it in a while so you'd have to check the wiki which has a link to the manpage.


Time is a great teacher, but unfortunately it kills all its pupils ... - Louis Hector Berlioz

Offline

#5 2012-08-28 17:54:06

2ManyDogs
Forum Fellow
Registered: 2012-01-15
Posts: 4,648

Re: [SOLVED] Trayer position

bgc1954 wrote:

I believe stalonetray has a geometry setting but I haven't used it in a while so you'd have to check the wiki which has a link to the manpage.

--geometry geometry_spec, geometry geometry_spec
           Set tray`s initial geometry to geometry_spec, specified in standard X notation: widthxheight[+x[+y]], where width and height are specified in
           icon slot multiples. Default value: 1x1+0-0.

(edit) -- you're right bgc. I just did it because I have stalonetray installed and I use it. I'll just point next time. wink

Last edited by 2ManyDogs (2012-08-28 18:53:10)

Offline

#6 2012-08-28 18:15:09

bgc1954
Member
From: Edmonton, AB, Canada
Registered: 2006-03-14
Posts: 1,160

Re: [SOLVED] Trayer position

@2manydogs - I suppose I could have done the same for him but I thought I'd just point him in the right direction. wink


Time is a great teacher, but unfortunately it kills all its pupils ... - Louis Hector Berlioz

Offline

#7 2012-08-29 07:29:12

DexterLB
Member
Registered: 2011-06-20
Posts: 51

Re: [SOLVED] Trayer position

stalonetray works perfectly, thanks both of you
and yeah, the pointer was enough, no need to quote the man page big_smile


The best solution to a problem is usually the easiest one.

Offline

#8 2012-08-29 08:17:03

bernarcher
Forum Fellow
From: Germany
Registered: 2009-02-17
Posts: 2,281

Re: [SOLVED] Trayer position

DexterLB please mark this thread as [SOLVED] then. See: Forum Rules


To know or not to know ...
... the questions remain forever.

Offline

Board footer

Powered by FluxBB