You are not logged in.

#1 2012-09-03 10:44:54

kayaman
Member
Registered: 2012-09-03
Posts: 10

b43 module wont load wlan interface

hi,

i followed the wiki https://wiki.archlinux.org/index.php/Broadcom_wireless.

i have the Broadcom Corporation BCM43228 802.11a/b/g/n wlan card and i load the b43 module, also firmware and fwcutter is installed:

[-@- ~]$ lspci |grep Broad
02:00.0 Network controller: Broadcom Corporation BCM43228 802.11a/b/g/n
[-@- ~]$ lsmod |grep b43
b43                   353762  0 
ssb                    49827  1 b43
pcmcia                 35785  2 b43,ssb
bcma                   25146  1 b43
mmc_core               81526  4 b43,ssb,sdhci,sdhci_pci
mac80211              416391  1 b43
cfg80211              173210  2 b43,mac80211
[-@- ~]$ pacman -Q b43-fwcutter
b43-fwcutter 015-1
[-@- ~]$ pacman -Q b43-firmware
b43-firmware 5.100.138-2

i tried legacy.. same problem and i tried wl, which didnt even load any interface anymore.
There is no output!! when i: dmesg |grep b43

still no interface.

~]$ iwconfig
eth0      no wireless extensions.

lo        no wireless extensions.
~]$ ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN mode DEFAULT 
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT qlen 1000
    link/ether d4:be:d9:27:6e:e7 brd ff:ff:ff:ff:ff:ff
~]$ /etc/rc.d/net-auto-wireless start
/etc/rc.conf: Zeile 1: +#: Kommando nicht gefunden.
/etc/rc.conf: Zeile 1: +#: Kommando nicht gefunden.
:: Starting netcfg auto-wireless mode for interface wlan0                [FAIL]

any ideas?
ty

Offline

#2 2012-09-03 10:54:07

Gusar
Member
Registered: 2009-08-25
Posts: 3,431

Re: b43 module wont load wlan interface

http://www.spinics.net/lists/linux-wire … 94595.html <- no idea if that patch is enough, but it's the first step in trying the get it working.

You could also try the broadcom-wl driver.

Edit: From what I read, that patch is not enough. It's just the first step to get the card recognized, but further code in the b43 driver is needed for full support. So broadcom-wl is your only option.

Last edited by Gusar (2012-09-03 11:23:15)

Offline

#3 2012-09-03 10:57:02

wonder
Developer
From: Bucharest, Romania
Registered: 2006-07-05
Posts: 5,937
Website

Re: b43 module wont load wlan interface

post dmesg.


Give what you have. To someone, it may be better than you dare to think.
Blog

Offline

#4 2012-09-03 11:34:53

kayaman
Member
Registered: 2012-09-03
Posts: 10

Re: b43 module wont load wlan interface

as i said i tried wl already and it doesnt work at all hmm

if im correct i do need the source code to patch this? because i cant find any code in /usr/src/linux-3.5.3-1-ARCH/drivers/bcma only a Kconfig file  ... if this is the correct location

dmesg output:

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.5.3-1-ARCH (tobias@T-POWA-LX) (gcc version 4.7.1 20120721 (prerelease) (GCC) ) #1 SMP PREEMPT Sun Aug 26 09:14:51 CEST 2012
[    0.000000] Command line: root=/dev/sda1 ro initrd=../initramfs-linux.img BOOT_IMAGE=../vmlinuz-linux 
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x00000000000913ff] usable
[    0.000000] BIOS-e820: [mem 0x0000000000091400-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000020200000-0x000000003fffffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000040000000-0x00000000401fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000040200000-0x00000000caa24fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000caa25000-0x00000000caa68fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000caa69000-0x00000000cadb6fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000cadb7000-0x00000000cade6fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000cade7000-0x00000000cafe6fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cafe7000-0x00000000caffefff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000cafff000-0x00000000caffffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ffc00000-0x00000000ffc1ffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000022dffffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] DMI 2.6 present.
[    0.000000] DMI: Dell Inc. Latitude E6520/0CMN08, BIOS A08 10/18/2011
[    0.000000] e820: update [mem 0x00000000-0x0000ffff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] No AGP bridge found
[    0.000000] e820: last_pfn = 0x22e000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 080000000 mask FC0000000 write-back
[    0.000000]   2 base 0C0000000 mask FF8000000 write-back
[    0.000000]   3 base 0C8000000 mask FFC000000 write-back
[    0.000000]   4 base 0CB000000 mask FFF000000 uncachable
[    0.000000]   5 base 100000000 mask F00000000 write-back
[    0.000000]   6 base 200000000 mask FE0000000 write-back
[    0.000000]   7 base 220000000 mask FF0000000 write-back
[    0.000000]   8 base 22E000000 mask FFE000000 uncachable
[    0.000000]   9 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820: update [mem 0xcb000000-0xffffffff] usable ==> reserved
[    0.000000] e820: last_pfn = 0xcb000 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [mem 0x000f1a70-0x000f1a7f] mapped at [ffff8800000f1a70]
[    0.000000] initial memory mapped: [mem 0x00000000-0x1fffffff]
[    0.000000] Base memory trampoline at [ffff88000008b000] 8b000 size 24576
[    0.000000] init_memory_mapping: [mem 0x00000000-0xcaffffff]
[    0.000000]  [mem 0x00000000-0xcaffffff] page 2M
[    0.000000] kernel direct mapping tables up to 0xcaffffff @ [mem 0x1f6ce000-0x1fd2afff]
[    0.000000] init_memory_mapping: [mem 0x100000000-0x22dffffff]
[    0.000000]  [mem 0x100000000-0x22dffffff] page 2M
[    0.000000] kernel direct mapping tables up to 0x22dffffff @ [mem 0xcadad000-0xcadb6fff]
[    0.000000] RAMDISK: [mem 0x1fd2b000-0x1fffefff]
[    0.000000] ACPI: RSDP 00000000000fe300 00024 (v02 DELL  )
[    0.000000] ACPI: XSDT 00000000caffde18 00074 (v01 DELL    CBX3    06222004 MSFT 00010013)
[    0.000000] ACPI: FACP 00000000caf77d98 000F4 (v04 DELL    CBX3    06222004 MSFT 00010013)
[    0.000000] ACPI Warning: 32/64 FACS address mismatch in FADT - two FACS tables! (20120320/tbfadt-378)
[    0.000000] ACPI Warning: 32/64X FACS address mismatch in FADT - 0xCAFD4E40/0x00000000CAFD4D40, using 32 (20120320/tbfadt-502)
[    0.000000] ACPI: DSDT 00000000caf45018 08774 (v02 INT430 SYSFexxx 00001001 INTL 20090903)
[    0.000000] ACPI: FACS 00000000cafd4e40 00040
[    0.000000] ACPI: APIC 00000000caffcf18 000CC (v02 DELL    CBX3    06222004 MSFT 00010013)
[    0.000000] ACPI: TCPA 00000000cafd5d18 00032 (v02                 00000000      00000000)
[    0.000000] ACPI: SSDT 00000000caf78a98 002F9 (v01 DELLTP      TPM 00003000 INTL 20090903)
[    0.000000] ACPI: MCFG 00000000cafd5c98 0003C (v01 DELL   SNDYBRDG 06222004 MSFT 00000097)
[    0.000000] ACPI: HPET 00000000cafd5c18 00038 (v01 A M I   PCHHPET 06222004 AMI. 00000003)
[    0.000000] ACPI: BOOT 00000000cafd5b98 00028 (v01 DELL   CBX3     06222004 AMI  00010013)
[    0.000000] ACPI: SSDT 00000000caf5c018 00804 (v01  PmRef  Cpu0Ist 00003000 INTL 20090903)
[    0.000000] ACPI: SSDT 00000000caf5b018 00996 (v01  PmRef    CpuPm 00003000 INTL 20090903)
[    0.000000] ACPI: SLIC 00000000caf65c18 00176 (v03 DELL    CBX3    06222004 MSFT 00010013)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x000000022dffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x22dffffff]
[    0.000000]   NODE_DATA [mem 0x22dffc000-0x22dffffff]
[    0.000000]  [ffffea0000000000-ffffea0008bfffff] PMD -> [ffff880225600000-ffff88022d5fffff] on node 0
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00010000-0x00ffffff]
[    0.000000]   DMA32    [mem 0x01000000-0xffffffff]
[    0.000000]   Normal   [mem 0x100000000-0x22dffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00010000-0x00090fff]
[    0.000000]   node   0: [mem 0x00100000-0x1fffffff]
[    0.000000]   node   0: [mem 0x20200000-0x3fffffff]
[    0.000000]   node   0: [mem 0x40200000-0xcaa24fff]
[    0.000000]   node   0: [mem 0xcaa69000-0xcadb6fff]
[    0.000000]   node   0: [mem 0xcafff000-0xcaffffff]
[    0.000000]   node   0: [mem 0x100000000-0x22dffffff]
[    0.000000] On node 0 totalpages: 2066677
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 6 pages reserved
[    0.000000]   DMA zone: 3899 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 16320 pages used for memmap
[    0.000000]   DMA32 zone: 809396 pages, LIFO batch:31
[    0.000000]   Normal zone: 19328 pages used for memmap
[    0.000000]   Normal zone: 1217664 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x08] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x09] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x0a] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x0b] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x0c] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x0d] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x0e] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x10] lapic_id[0x0f] disabled)
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[    0.000000] SMP: Allowing 16 CPUs, 12 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 0000000000091000 - 0000000000092000
[    0.000000] PM: Registered nosave memory: 0000000000092000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[    0.000000] PM: Registered nosave memory: 0000000020000000 - 0000000020200000
[    0.000000] PM: Registered nosave memory: 0000000040000000 - 0000000040200000
[    0.000000] PM: Registered nosave memory: 00000000caa25000 - 00000000caa69000
[    0.000000] PM: Registered nosave memory: 00000000cadb7000 - 00000000cade7000
[    0.000000] PM: Registered nosave memory: 00000000cade7000 - 00000000cafe7000
[    0.000000] PM: Registered nosave memory: 00000000cafe7000 - 00000000cafff000
[    0.000000] PM: Registered nosave memory: 00000000cb000000 - 00000000fed1c000
[    0.000000] PM: Registered nosave memory: 00000000fed1c000 - 00000000fed20000
[    0.000000] PM: Registered nosave memory: 00000000fed20000 - 00000000ffc00000
[    0.000000] PM: Registered nosave memory: 00000000ffc00000 - 00000000ffc20000
[    0.000000] PM: Registered nosave memory: 00000000ffc20000 - 0000000100000000
[    0.000000] e820: [mem 0xcb000000-0xfed1bfff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:16 nr_node_ids:1
[    0.000000] PERCPU: Embedded 28 pages/cpu @ffff88022dc00000 s83392 r8192 d23104 u131072
[    0.000000] pcpu-alloc: s83392 r8192 d23104 u131072 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 2030959
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: root=/dev/sda1 ro initrd=../initramfs-linux.img BOOT_IMAGE=../vmlinuz-linux 
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] __ex_table already sorted, skipping sort
[    0.000000] xsave/xrstor: enabled xstate_bv 0x7, cntxt size 0x340
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 8053656k/9142272k available (4635k kernel code, 875564k absent, 213052k reserved, 4212k data, 756k init)
[    0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] 	Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] NR_IRQS:4352 nr_irqs:808 16
[    0.000000] Extended CMOS year: 2000
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] allocated 33554432 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] hpet clockevent registered
[    0.000000] Fast TSC calibration using PIT
[    0.003333] Detected 2394.808 MHz processor.
[    0.000003] Calibrating delay loop (skipped), value calculated using timer frequency.. 4791.18 BogoMIPS (lpj=7982693)
[    0.000005] pid_max: default: 32768 minimum: 301
[    0.000030] Security Framework initialized
[    0.000033] AppArmor: AppArmor disabled by boot time parameter
[    0.000513] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.002138] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.002840] Mount-cache hash table entries: 256
[    0.003007] Initializing cgroup subsys cpuacct
[    0.003009] Initializing cgroup subsys memory
[    0.003016] Initializing cgroup subsys devices
[    0.003017] Initializing cgroup subsys freezer
[    0.003018] Initializing cgroup subsys net_cls
[    0.003037] Initializing cgroup subsys blkio
[    0.003061] CPU: Physical Processor ID: 0
[    0.003061] CPU: Processor Core ID: 0
[    0.003065] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[    0.003065] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[    0.003068] mce: CPU supports 7 MCE banks
[    0.003079] CPU0: Thermal monitoring enabled (TM1)
[    0.003085] using mwait in idle threads.
[    0.004268] ACPI: Core revision 20120320
[    0.009622] ftrace: allocating 17956 entries in 71 pages
[    0.018390] Switched APIC routing to physical flat.
[    0.018810] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.051768] CPU0: Intel(R) Core(TM) i5-2430M CPU @ 2.40GHz stepping 07
[    0.156132] Performance Events: PEBS fmt1+, 16-deep LBR, SandyBridge events, Intel PMU driver.
[    0.156137] PEBS disabled due to CPU errata.
[    0.156139] ... version:                3
[    0.156140] ... bit width:              48
[    0.156140] ... generic registers:      4
[    0.156141] ... value mask:             0000ffffffffffff
[    0.156142] ... max period:             000000007fffffff
[    0.156143] ... fixed-purpose events:   3
[    0.156144] ... event mask:             000000070000000f
[    0.176278] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.189433] Booting Node   0, Processors  #1 #2 #3
[    0.249280] Brought up 4 CPUs
[    0.249283] Total of 4 processors activated (19166.73 BogoMIPS).
[    0.252572] devtmpfs: initialized
[    0.253763] PM: Registering ACPI NVS region [mem 0xcade7000-0xcafe6fff] (2097152 bytes)
[    0.254421] NET: Registered protocol family 16
[    0.254532] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.254534] ACPI: bus type pci registered
[    0.254600] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[    0.254602] PCI: not using MMCONFIG
[    0.254603] PCI: Using configuration type 1 for base access
[    0.254611] dmi type 0xB1 record - unknown flag
[    0.255120] bio: create slab <bio-0> at 0
[    0.255168] ACPI: Added _OSI(Module Device)
[    0.255169] ACPI: Added _OSI(Processor Device)
[    0.255171] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.255172] ACPI: Added _OSI(Processor Aggregator Device)
[    0.256424] ACPI: EC: Look up EC in DSDT
[    0.259938] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[    0.267388] ACPI: SSDT 00000000cadd7798 00727 (v01  PmRef  Cpu0Cst 00003001 INTL 20090903)
[    0.267707] ACPI: Dynamic OEM Table Load:
[    0.267709] ACPI: SSDT           (null) 00727 (v01  PmRef  Cpu0Cst 00003001 INTL 20090903)
[    0.267933] ACPI: SSDT 00000000cadd8a98 00303 (v01  PmRef    ApIst 00003000 INTL 20090903)
[    0.268276] ACPI: Dynamic OEM Table Load:
[    0.268279] ACPI: SSDT           (null) 00303 (v01  PmRef    ApIst 00003000 INTL 20090903)
[    0.268379] ACPI: SSDT 00000000cadd6d98 00119 (v01  PmRef    ApCst 00003000 INTL 20090903)
[    0.268690] ACPI: Dynamic OEM Table Load:
[    0.268692] ACPI: SSDT           (null) 00119 (v01  PmRef    ApCst 00003000 INTL 20090903)
[    0.270135] ACPI: Interpreter enabled
[    0.270138] ACPI: (supports S0 S3 S4 S5)
[    0.270157] ACPI: Using IOAPIC for interrupt routing
[    0.270172] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[    0.270515] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in ACPI motherboard resources
[    0.288975] ACPI: EC: GPE = 0x10, I/O: command/status = 0x934, data = 0x930
[    0.290564] ACPI: No dock devices found.
[    0.290568] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.290824] \_SB_.PCI0:_OSC invalid UUID
[    0.290825] _OSC request data:1 8 1f 
[    0.290829] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[    0.291258] pci_root PNP0A08:00: host bridge window [io  0x0000-0x0cf7]
[    0.291261] pci_root PNP0A08:00: host bridge window [io  0x0d00-0xffff]
[    0.291262] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[    0.291265] pci_root PNP0A08:00: host bridge window [mem 0xcfa00000-0xfeafffff]
[    0.291267] pci_root PNP0A08:00: host bridge window [mem 0xfed40000-0xfed44fff]
[    0.291295] PCI host bridge to bus 0000:00
[    0.291297] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.291298] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff]
[    0.291300] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.291302] pci_bus 0000:00: root bus resource [mem 0xcfa00000-0xfeafffff]
[    0.291303] pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed44fff]
[    0.291311] pci 0000:00:00.0: [8086:0104] type 00 class 0x060000
[    0.291347] pci 0000:00:02.0: [8086:0116] type 00 class 0x030000
[    0.291357] pci 0000:00:02.0: reg 10: [mem 0xe1400000-0xe17fffff 64bit]
[    0.291363] pci 0000:00:02.0: reg 18: [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.291367] pci 0000:00:02.0: reg 20: [io  0x4000-0x403f]
[    0.291421] pci 0000:00:16.0: [8086:1c3a] type 00 class 0x078000
[    0.291445] pci 0000:00:16.0: reg 10: [mem 0xe2eb0000-0xe2eb000f 64bit]
[    0.291523] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[    0.291556] pci 0000:00:19.0: [8086:1502] type 00 class 0x020000
[    0.291575] pci 0000:00:19.0: reg 10: [mem 0xe2e00000-0xe2e1ffff]
[    0.291584] pci 0000:00:19.0: reg 14: [mem 0xe2e80000-0xe2e80fff]
[    0.291593] pci 0000:00:19.0: reg 18: [io  0x4080-0x409f]
[    0.291658] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[    0.291685] pci 0000:00:1a.0: [8086:1c2d] type 00 class 0x0c0320
[    0.291706] pci 0000:00:1a.0: reg 10: [mem 0xe2e70000-0xe2e703ff]
[    0.291797] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[    0.291823] pci 0000:00:1b.0: [8086:1c20] type 00 class 0x040300
[    0.291839] pci 0000:00:1b.0: reg 10: [mem 0xe2e60000-0xe2e63fff 64bit]
[    0.291908] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.291936] pci 0000:00:1c.0: [8086:1c10] type 01 class 0x060400
[    0.292064] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.292103] pci 0000:00:1c.1: [8086:1c12] type 01 class 0x060400
[    0.292234] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.292275] pci 0000:00:1c.2: [8086:1c14] type 01 class 0x060400
[    0.292404] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[    0.292442] pci 0000:00:1c.3: [8086:1c16] type 01 class 0x060400
[    0.292573] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[    0.292615] pci 0000:00:1c.5: [8086:1c1a] type 01 class 0x060400
[    0.292699] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[    0.292734] pci 0000:00:1d.0: [8086:1c26] type 00 class 0x0c0320
[    0.292755] pci 0000:00:1d.0: reg 10: [mem 0xe2e50000-0xe2e503ff]
[    0.292846] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    0.292873] pci 0000:00:1f.0: [8086:1c4f] type 00 class 0x060100
[    0.292999] pci 0000:00:1f.2: [8086:282a] type 00 class 0x010400
[    0.293018] pci 0000:00:1f.2: reg 10: [io  0x40d0-0x40d7]
[    0.293026] pci 0000:00:1f.2: reg 14: [io  0x40c0-0x40c3]
[    0.293034] pci 0000:00:1f.2: reg 18: [io  0x40b0-0x40b7]
[    0.293043] pci 0000:00:1f.2: reg 1c: [io  0x40a0-0x40a3]
[    0.293051] pci 0000:00:1f.2: reg 20: [io  0x4060-0x407f]
[    0.293059] pci 0000:00:1f.2: reg 24: [mem 0xe2e40000-0xe2e407ff]
[    0.293105] pci 0000:00:1f.2: PME# supported from D3hot
[    0.293124] pci 0000:00:1f.3: [8086:1c22] type 00 class 0x0c0500
[    0.293141] pci 0000:00:1f.3: reg 10: [mem 0xe2e30000-0xe2e300ff 64bit]
[    0.293162] pci 0000:00:1f.3: reg 20: [io  0x4040-0x405f]
[    0.293261] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[    0.293403] pci 0000:02:00.0: [14e4:4359] type 00 class 0x028000
[    0.293440] pci 0000:02:00.0: reg 10: [mem 0xe2d00000-0xe2d03fff 64bit]
[    0.293626] pci 0000:02:00.0: supports D1 D2
[    0.293627] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[    0.299313] pci 0000:00:1c.1: PCI bridge to [bus 02-02]
[    0.299334] pci 0000:00:1c.1:   bridge window [mem 0xe2d00000-0xe2dfffff]
[    0.299383] pci 0000:00:1c.2: PCI bridge to [bus 03-08]
[    0.299388] pci 0000:00:1c.2:   bridge window [io  0x3000-0x3fff]
[    0.299392] pci 0000:00:1c.2:   bridge window [mem 0xe2200000-0xe2bfffff]
[    0.299398] pci 0000:00:1c.2:   bridge window [mem 0xe0a00000-0xe13fffff 64bit pref]
[    0.299443] pci 0000:00:1c.3: PCI bridge to [bus 09-09]
[    0.299447] pci 0000:00:1c.3:   bridge window [io  0x2000-0x2fff]
[    0.299451] pci 0000:00:1c.3:   bridge window [mem 0xe1800000-0xe21fffff]
[    0.299457] pci 0000:00:1c.3:   bridge window [mem 0xe0000000-0xe09fffff 64bit pref]
[    0.299546] pci 0000:0a:00.0: [1217:13f7] type 00 class 0x0c0010
[    0.299580] pci 0000:0a:00.0: reg 10: [mem 0xe2c30000-0xe2c30fff]
[    0.299829] pci 0000:0a:00.0: supports D1 D2
[    0.299830] pci 0000:0a:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.299916] pci 0000:0a:00.1: [1217:8321] type 00 class 0x080501
[    0.299949] pci 0000:0a:00.1: reg 10: [mem 0xe2c20000-0xe2c201ff]
[    0.300195] pci 0000:0a:00.1: supports D1 D2
[    0.300197] pci 0000:0a:00.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.300275] pci 0000:0a:00.2: [1217:8331] type 00 class 0x018000
[    0.300308] pci 0000:0a:00.2: reg 10: [mem 0xe2c10000-0xe2c103ff]
[    0.300353] pci 0000:0a:00.2: reg 18: [mem 0xe2c00000-0xe2c003ff]
[    0.300559] pci 0000:0a:00.2: supports D1 D2
[    0.300560] pci 0000:0a:00.2: PME# supported from D0 D1 D2 D3hot D3cold
[    0.305967] pci 0000:00:1c.5: PCI bridge to [bus 0a-0a]
[    0.305988] pci 0000:00:1c.5:   bridge window [mem 0xe2c00000-0xe2cfffff]
[    0.306031] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.306140] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[    0.306166] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[    0.306193] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
[    0.306218] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP06._PRT]
[    0.306252] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[    0.306315] \_SB_.PCI0:_OSC invalid UUID
[    0.306316] _OSC request data:1 1f 1f 
[    0.306320]  pci0000:00: Requesting ACPI _OSC control (0x1d)
[    0.306345] \_SB_.PCI0:_OSC invalid UUID
[    0.306346] _OSC request data:1 0 1d 
[    0.306349]  pci0000:00: ACPI _OSC request failed (AE_ERROR), returned control mask: 0x1d
[    0.306350] ACPI _OSC control for PCIe not granted, disabling ASPM
[    0.309122] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.309161] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[    0.309198] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.309238] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[    0.309274] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 *5 6 7 10 12 14 15)
[    0.309310] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[    0.309346] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 *3 4 5 6 7 10 12 14 15)
[    0.309381] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[    0.309457] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    0.309463] vgaarb: loaded
[    0.309464] vgaarb: bridge control possible 0000:00:02.0
[    0.309491] PCI: Using ACPI for IRQ routing
[    0.311132] PCI: pci_cache_line_size set to 64 bytes
[    0.311255] e820: reserve RAM buffer [mem 0x00091400-0x0009ffff]
[    0.311257] e820: reserve RAM buffer [mem 0xcaa25000-0xcbffffff]
[    0.311259] e820: reserve RAM buffer [mem 0xcadb7000-0xcbffffff]
[    0.311260] e820: reserve RAM buffer [mem 0xcb000000-0xcbffffff]
[    0.311262] e820: reserve RAM buffer [mem 0x22e000000-0x22fffffff]
[    0.311344] NetLabel: Initializing
[    0.311345] NetLabel:  domain hash size = 128
[    0.311346] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.311356] NetLabel:  unlabeled traffic allowed by default
[    0.311370] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[    0.311376] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[    0.314390] Switching to clocksource hpet
[    0.320004] pnp: PnP ACPI init
[    0.320020] ACPI: bus type pnp registered
[    0.320326] pnp 00:00: [bus 00-3e]
[    0.320330] pnp 00:00: [io  0x0000-0x0cf7 window]
[    0.320332] pnp 00:00: [io  0x0cf8-0x0cff]
[    0.320334] pnp 00:00: [io  0x0d00-0xffff window]
[    0.320336] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[    0.320337] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[    0.320339] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[    0.320340] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[    0.320342] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[    0.320344] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[    0.320345] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[    0.320347] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[    0.321620] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[    0.321633] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[    0.321634] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[    0.321636] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[    0.321637] pnp 00:00: [mem 0x000ec000-0x000effff window]
[    0.321639] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[    0.321641] pnp 00:00: [mem 0xcfa00000-0xfeafffff window]
[    0.321642] pnp 00:00: [mem 0xfed40000-0xfed44fff window]
[    0.321737] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[    0.341135] pnp 00:01: [io  0x0000-0x001f]
[    0.341137] pnp 00:01: [io  0x0081-0x0091]
[    0.341138] pnp 00:01: [io  0x0093-0x009f]
[    0.341140] pnp 00:01: [io  0x00c0-0x00df]
[    0.341141] pnp 00:01: [dma 4]
[    0.341163] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.341335] pnp 00:02: [mem 0xff000000-0xffffffff]
[    0.341358] pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active)
[    0.341496] pnp 00:03: [mem 0xfed00000-0xfed003ff]
[    0.344472] system 00:03: [mem 0xfed00000-0xfed003ff] has been reserved
[    0.344475] system 00:03: Plug and Play ACPI device, IDs PNP0103 PNP0c01 (active)
[    0.344484] pnp 00:04: [io  0x00f0]
[    0.344494] pnp 00:04: [irq 13]
[    0.344514] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.344523] pnp 00:05: [io  0x002e-0x002f]
[    0.344525] pnp 00:05: [io  0x004e-0x004f]
[    0.344526] pnp 00:05: [io  0x0061]
[    0.344527] pnp 00:05: [io  0x0063]
[    0.344529] pnp 00:05: [io  0x0065]
[    0.344530] pnp 00:05: [io  0x0067]
[    0.344531] pnp 00:05: [io  0x0070]
[    0.344533] pnp 00:05: [io  0x0080]
[    0.344534] pnp 00:05: [io  0x0092]
[    0.344535] pnp 00:05: [io  0x00b2-0x00b3]
[    0.344537] pnp 00:05: [io  0x0680-0x069f]
[    0.344538] pnp 00:05: [io  0x1000-0x100f]
[    0.344540] pnp 00:05: [io  0xffff]
[    0.344541] pnp 00:05: [io  0xffff]
[    0.344542] pnp 00:05: [io  0x0400-0x047f]
[    0.344544] pnp 00:05: [io  0x0500-0x057f]
[    0.344545] pnp 00:05: [io  0x164e-0x164f]
[    0.344575] system 00:05: [io  0x0680-0x069f] has been reserved
[    0.344577] system 00:05: [io  0x1000-0x100f] has been reserved
[    0.344579] system 00:05: [io  0xffff] has been reserved
[    0.344580] system 00:05: [io  0xffff] has been reserved
[    0.344582] system 00:05: [io  0x0400-0x047f] has been reserved
[    0.344584] system 00:05: [io  0x0500-0x057f] has been reserved
[    0.344586] system 00:05: [io  0x164e-0x164f] has been reserved
[    0.344588] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.344594] pnp 00:06: [io  0x0070-0x0077]
[    0.344599] pnp 00:06: [irq 8]
[    0.344617] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.344624] pnp 00:07: [io  0x0060]
[    0.344626] pnp 00:07: [io  0x0064]
[    0.344630] pnp 00:07: [irq 1]
[    0.344647] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.345517] pnp 00:08: Plug and Play ACPI device, IDs PNP0401 (disabled)
[    0.345528] pnp 00:09: [irq 12]
[    0.345546] pnp 00:09: Plug and Play ACPI device, IDs DLL0494 PNP0f13 (active)
[    0.345570] pnp 00:0a: [mem 0xfed40000-0xfed44fff]
[    0.345590] pnp 00:0a: Plug and Play ACPI device, IDs BCM0102 PNP0c31 (active)
[    0.345696] pnp 00:0b: [mem 0xfed1c000-0xfed1ffff]
[    0.345698] pnp 00:0b: [mem 0xfed10000-0xfed17fff]
[    0.345699] pnp 00:0b: [mem 0xfed18000-0xfed18fff]
[    0.345701] pnp 00:0b: [mem 0xfed19000-0xfed19fff]
[    0.345702] pnp 00:0b: [mem 0xf8000000-0xfbffffff]
[    0.345705] pnp 00:0b: [mem 0xfed20000-0xfed3ffff]
[    0.345707] pnp 00:0b: [mem 0xfed90000-0xfed93fff]
[    0.345708] pnp 00:0b: [mem 0xfed45000-0xfed8ffff]
[    0.345709] pnp 00:0b: [mem 0xff000000-0xffffffff]
[    0.345711] pnp 00:0b: [mem 0xfee00000-0xfeefffff]
[    0.345713] pnp 00:0b: [mem 0x00000000-0xffffffffffffffff disabled]
[    0.345714] pnp 00:0b: [mem 0x00000000-0xffffffffffffffff disabled]
[    0.345754] system 00:0b: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.345756] system 00:0b: [mem 0xfed10000-0xfed17fff] has been reserved
[    0.345758] system 00:0b: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.345759] system 00:0b: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.345761] system 00:0b: [mem 0xf8000000-0xfbffffff] has been reserved
[    0.345763] system 00:0b: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.345765] system 00:0b: [mem 0xfed90000-0xfed93fff] has been reserved
[    0.345767] system 00:0b: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.345769] system 00:0b: [mem 0xff000000-0xffffffff] could not be reserved
[    0.345770] system 00:0b: [mem 0xfee00000-0xfeefffff] has been reserved
[    0.345773] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.346267] pnp 00:0c: [irq 23]
[    0.346294] pnp 00:0c: Plug and Play ACPI device, IDs SMO8800 (active)
[    0.348336] pnp 00:0d: [mem 0x20000000-0x201fffff]
[    0.348338] pnp 00:0d: [mem 0x40000000-0x401fffff]
[    0.348390] system 00:0d: [mem 0x20000000-0x201fffff] has been reserved
[    0.348392] system 00:0d: [mem 0x40000000-0x401fffff] has been reserved
[    0.348395] system 00:0d: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.348403] pnp: PnP ACPI: found 14 devices
[    0.348404] ACPI: ACPI bus type pnp unregistered
[    0.354876] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[    0.354895] pci 0000:00:1c.1: PCI bridge to [bus 02-02]
[    0.354902] pci 0000:00:1c.1:   bridge window [mem 0xe2d00000-0xe2dfffff]
[    0.354913] pci 0000:00:1c.2: PCI bridge to [bus 03-08]
[    0.354917] pci 0000:00:1c.2:   bridge window [io  0x3000-0x3fff]
[    0.354924] pci 0000:00:1c.2:   bridge window [mem 0xe2200000-0xe2bfffff]
[    0.354929] pci 0000:00:1c.2:   bridge window [mem 0xe0a00000-0xe13fffff 64bit pref]
[    0.354938] pci 0000:00:1c.3: PCI bridge to [bus 09-09]
[    0.354941] pci 0000:00:1c.3:   bridge window [io  0x2000-0x2fff]
[    0.354948] pci 0000:00:1c.3:   bridge window [mem 0xe1800000-0xe21fffff]
[    0.354953] pci 0000:00:1c.3:   bridge window [mem 0xe0000000-0xe09fffff 64bit pref]
[    0.354961] pci 0000:00:1c.5: PCI bridge to [bus 0a-0a]
[    0.354967] pci 0000:00:1c.5:   bridge window [mem 0xe2c00000-0xe2cfffff]
[    0.355025] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.355027] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.355029] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.355030] pci_bus 0000:00: resource 7 [mem 0xcfa00000-0xfeafffff]
[    0.355032] pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfed44fff]
[    0.355034] pci_bus 0000:02: resource 1 [mem 0xe2d00000-0xe2dfffff]
[    0.355036] pci_bus 0000:03: resource 0 [io  0x3000-0x3fff]
[    0.355037] pci_bus 0000:03: resource 1 [mem 0xe2200000-0xe2bfffff]
[    0.355039] pci_bus 0000:03: resource 2 [mem 0xe0a00000-0xe13fffff 64bit pref]
[    0.355041] pci_bus 0000:09: resource 0 [io  0x2000-0x2fff]
[    0.355042] pci_bus 0000:09: resource 1 [mem 0xe1800000-0xe21fffff]
[    0.355044] pci_bus 0000:09: resource 2 [mem 0xe0000000-0xe09fffff 64bit pref]
[    0.355046] pci_bus 0000:0a: resource 1 [mem 0xe2c00000-0xe2cfffff]
[    0.355069] NET: Registered protocol family 2
[    0.355221] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.355873] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[    0.357017] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.357141] TCP: Hash tables configured (established 524288 bind 65536)
[    0.357142] TCP: reno registered
[    0.357153] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[    0.357181] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[    0.357266] NET: Registered protocol family 1
[    0.357278] pci 0000:00:02.0: Boot video device
[    0.357437] PCI: CLS 64 bytes, default 64
[    0.357473] Unpacking initramfs...
[    0.408001] Freeing initrd memory: 2896k freed
[    0.408341] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.408345] software IO TLB [mem 0xc6a25000-0xcaa24fff] (64MB) mapped at [ffff8800c6a25000-ffff8800caa24fff]
[    0.408367] Simple Boot Flag at 0xf3 set to 0x1
[    0.408786] audit: initializing netlink socket (disabled)
[    0.408799] type=2000 audit(1346658808.303:1): initialized
[    0.419313] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.420944] VFS: Disk quotas dquot_6.5.2
[    0.420985] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.421064] msgmni has been set to 15735
[    0.421234] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.421262] io scheduler noop registered
[    0.421264] io scheduler deadline registered
[    0.421305] io scheduler cfq registered (default)
[    0.421740] intel_idle: MWAIT substates: 0x21120
[    0.421741] intel_idle: v0.4 model 0x2A
[    0.421742] intel_idle: lapic_timer_reliable_states 0xffffffff
[    0.421774] GHES: HEST is not enabled!
[    0.421815] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.422178] Linux agpgart interface v0.103
[    0.422240] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    0.422488] i8042: Warning: Keylock active
[    0.423675] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.423684] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.423776] mousedev: PS/2 mouse device common for all mice
[    0.423805] rtc_cmos 00:06: RTC can wake from S4
[    0.423942] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[    0.423975] rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs
[    0.424053] cpuidle: using governor ladder
[    0.424155] cpuidle: using governor menu
[    0.424273] drop_monitor: Initializing network drop monitor service
[    0.424336] TCP: cubic registered
[    0.424423] NET: Registered protocol family 10
[    0.424573] NET: Registered protocol family 17
[    0.424587] Key type dns_resolver registered
[    0.424860] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    0.424900] PM: Hibernation image not present or could not be loaded.
[    0.424910] registered taskstats version 1
[    0.425775] rtc_cmos 00:06: setting system clock to 2012-09-03 07:53:29 UTC (1346658809)
[    0.426873] Freeing unused kernel memory: 756k freed
[    0.426958] Write protecting the kernel read-only data: 8192k
[    0.433800] Freeing unused kernel memory: 1496k freed
[    0.435524] Freeing unused kernel memory: 616k freed
[    0.442243] systemd-udevd[49]: starting version 188
[    0.467403] ACPI: bus type usb registered
[    0.467498] usbcore: registered new interface driver usbfs
[    0.467513] usbcore: registered new interface driver hub
[    0.467668] usbcore: registered new device driver usb
[    0.468166] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.468223] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[    0.468228] ehci_hcd 0000:00:1a.0: EHCI Host Controller
[    0.468235] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[    0.468265] ehci_hcd 0000:00:1a.0: debug port 2
[    0.469024] SCSI subsystem initialized
[    0.470104] libata version 3.00 loaded.
[    0.472329] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
[    0.472352] ehci_hcd 0000:00:1a.0: irq 16, io mem 0xe2e70000
[    0.480859] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[    0.481027] hub 1-0:1.0: USB hub found
[    0.481033] hub 1-0:1.0: 2 ports detected
[    0.481192] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[    0.481197] ehci_hcd 0000:00:1d.0: EHCI Host Controller
[    0.481204] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    0.481237] ehci_hcd 0000:00:1d.0: debug port 2
[    0.485130] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
[    0.485149] ehci_hcd 0000:00:1d.0: irq 17, io mem 0xe2e50000
[    0.494259] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[    0.494494] hub 2-0:1.0: USB hub found
[    0.494498] hub 2-0:1.0: 2 ports detected
[    0.494581] ahci 0000:00:1f.2: version 3.0
[    0.494667] ahci 0000:00:1f.2: irq 40 for MSI/MSI-X
[    0.494703] ahci: SSS flag set, parallel bus scan disabled
[    0.507607] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x3b impl RAID mode
[    0.507612] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ems sxs apst 
[    0.507617] ahci 0000:00:1f.2: setting latency timer to 64
[    0.534731] scsi0 : ahci
[    0.534842] scsi1 : ahci
[    0.534924] scsi2 : ahci
[    0.535001] scsi3 : ahci
[    0.535073] scsi4 : ahci
[    0.535146] scsi5 : ahci
[    0.538957] ata1: SATA max UDMA/133 abar m2048@0xe2e40000 port 0xe2e40100 irq 40
[    0.538961] ata2: SATA max UDMA/133 abar m2048@0xe2e40000 port 0xe2e40180 irq 40
[    0.538963] ata3: DUMMY
[    0.538965] ata4: SATA max UDMA/133 abar m2048@0xe2e40000 port 0xe2e40280 irq 40
[    0.538968] ata5: SATA max UDMA/133 abar m2048@0xe2e40000 port 0xe2e40300 irq 40
[    0.538971] ata6: SATA max UDMA/133 abar m2048@0xe2e40000 port 0xe2e40380 irq 40
[    0.787174] usb 1-1: new high-speed USB device number 2 using ehci_hcd
[    0.857070] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    0.861401] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[    0.861900] ata1.00: ATA-8: ST320LT007-9ZV142, 0003DEM1, max UDMA/133
[    0.861909] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
[    0.866666] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[    0.867176] ata1.00: configured for UDMA/133
[    0.873860] scsi 0:0:0:0: Direct-Access     ATA      ST320LT007-9ZV14 0003 PQ: 0 ANSI: 5
[    0.911064] hub 1-1:1.0: USB hub found
[    0.911143] hub 1-1:1.0: 6 ports detected
[    1.016828] usb 2-1: new high-speed USB device number 2 using ehci_hcd
[    1.140751] hub 2-1:1.0: USB hub found
[    1.140928] hub 2-1:1.0: 8 ports detected
[    1.193239] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.203154] ata2.00: ATAPI: TSSTcorp DVD+/-RW TS-U633J, D800, max UDMA/100
[    1.206646] usb 1-1.4: new full-speed USB device number 3 using ehci_hcd
[    1.217988] ata2.00: configured for UDMA/100
[    1.225774] scsi 1:0:0:0: CD-ROM            TSSTcorp DVD+-RW TS-U633J D800 PQ: 0 ANSI: 5
[    1.373138] usb 1-1.5: new high-speed USB device number 4 using ehci_hcd
[    1.409565] Refined TSC clocksource calibration: 2394.560 MHz.
[    1.409571] Switching to clocksource tsc
[    1.542709] ata4: SATA link down (SStatus 0 SControl 300)
[    1.542835] usb 2-1.1: new low-speed USB device number 3 using ehci_hcd
[    1.696065] usb 2-1.4: new low-speed USB device number 4 using ehci_hcd
[    1.793898] usbcore: registered new interface driver usbhid
[    1.793904] usbhid: USB HID core driver
[    1.852414] usb 2-1.8: new full-speed USB device number 5 using ehci_hcd
[    1.862236] ata5: SATA link down (SStatus 0 SControl 300)
[    1.961943] usb 2-1.8: config 0 descriptor??
[    2.181759] ata6: SATA link down (SStatus 0 SControl 300)
[    2.182777] input: Dell Dell USB Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/input/input1
[    2.183210] hid-generic 0003:413C:3012.0001: input,hidraw0: USB HID v1.11 Mouse [Dell Dell USB Optical Mouse] on usb-0000:00:1d.0-1.1/input0
[    2.183421] input: Dell Dell USB Entry Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.0/input/input2
[    2.183569] hid-generic 0003:413C:2107.0002: input,hidraw1: USB HID v1.10 Keyboard [Dell Dell USB Entry Keyboard] on usb-0000:00:1d.0-1.4/input0
[    2.187247] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[    2.187250] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    2.187301] sd 0:0:0:0: [sda] Write Protect is off
[    2.187303] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.187323] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.191243] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.191250] cdrom: Uniform CD-ROM driver Revision: 3.20
[    2.191465] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    2.235424]  sda: sda1 sda2 sda3
[    2.236013] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.064248] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    5.158105] systemd-udevd[153]: starting version 189
[    5.613813] cfg80211: Calling CRDA to update world regulatory domain
[    5.727146] Broadcom 43xx driver loaded [ Features: PMNLS ]
[    5.878570] fuse init (API version 7.19)
[    5.916998] vboxdrv: Found 4 processor cores.
[    5.919571] vboxdrv: fAsync=0 offMin=0x230 offMax=0xdc8
[    5.919632] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[    5.919633] vboxdrv: Successfully loaded version 4.1.20_OSE (interface 0x00190000).
[    5.974213] [drm] Initialized drm 1.1.0 20060810
[    6.097560] wmi: Mapper loaded
[    6.119052] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[    6.134588] tpm_tis 00:0a: 1.2 TPM (device-id 0x2001, rev-id 32)
[    6.141884] agpgart-intel 0000:00:00.0: Intel Sandybridge Chipset
[    6.141993] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
[    6.142912] agpgart-intel 0000:00:00.0: detected 65536K stolen memory
[    6.143010] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[    6.185314] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input3
[    6.193414] ACPI: Lid Switch [LID]
[    6.193491] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
[    6.193498] ACPI: Power Button [PBTN]
[    6.195805] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input5
[    6.195811] ACPI: Sleep Button [SBTN]
[    6.195972] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input6
[    6.195976] ACPI: Power Button [PWRF]
[    6.229557] parport_pc 00:08: [io  0x0378-0x037b]
[    6.229571] parport_pc 00:08: [io  0x0278-0x027b]
[    6.229578] parport_pc 00:08: [io  0x03bc-0x03bf]
[    6.229585] parport_pc 00:08: [io  0x0378-0x037b]
[    6.229679] parport_pc 00:08: [irq 7]
[    6.242392] firewire_ohci 0000:0a:00.0: added OHCI v1.10 device as card 0, 8 IR + 8 IT contexts, quirks 0x10
[    6.262534] input: Dell WMI hotkeys as /devices/virtual/input/input7
[    6.276246] ACPI: Requesting acpi_cpufreq
[    6.287581] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \PMIO 1 (20120320/utaddress-251)
[    6.287589] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    6.287595] ACPI Warning: 0x0000000000000500-0x000000000000057f SystemIO conflicts with Region \GPIO 1 (20120320/utaddress-251)
[    6.287600] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    6.287602] lpc_ich: Resource conflict(s) found affecting gpio_ich
[    6.310597] ppdev: user-space parallel port driver
[    6.428460] Bluetooth: Core ver 2.16
[    6.428477] NET: Registered protocol family 31
[    6.428479] Bluetooth: HCI device and connection manager initialized
[    6.428481] Bluetooth: HCI socket layer initialized
[    6.428483] Bluetooth: L2CAP socket layer initialized
[    6.428488] Bluetooth: SCO socket layer initialized
[    6.430670] e1000e: Intel(R) PRO/1000 Network Driver - 2.0.0-k
[    6.430672] e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
[    6.430711] e1000e 0000:00:19.0: setting latency timer to 64
[    6.430793] e1000e 0000:00:19.0: (unregistered net_device): Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[    6.430827] e1000e 0000:00:19.0: irq 41 for MSI/MSI-X
[    6.446714] usbcore: registered new interface driver btusb
[    6.460388] Linux media interface: v0.10
[    6.533319] input: PC Speaker as /devices/platform/pcspkr/input/input8
[    6.536304] sdhci: Secure Digital Host Controller Interface driver
[    6.536306] sdhci: Copyright(c) Pierre Ossman
[    6.620790] ACPI: AC Adapter [AC] (on-line)
[    6.625828] thermal LNXTHERM:00: registered as thermal_zone0
[    6.625831] ACPI: Thermal Zone [THM] (25 C)
[    6.685668] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) d4:be:d9:27:6e:e7
[    6.685672] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[    6.685717] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: 4041FF-0FF
[    6.685748] mei 0000:00:16.0: setting latency timer to 64
[    6.685998] mei 0000:00:16.0: irq 42 for MSI/MSI-X
[    6.690599] ACPI Warning: 0x0000000000004040-0x000000000000405f SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20120320/utaddress-251)
[    6.690606] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    6.697865] ACPI Error: [DCK9] Namespace lookup failure, AE_ALREADY_EXISTS (20120320/dswload2-316)
[    6.697870] ACPI Exception: AE_ALREADY_EXISTS, During name lookup/catalog (20120320/psloop-231)
[    6.697873] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.LPTE.CLPS] (Node ffff880222065e10), AE_ALREADY_EXISTS (20120320/psparse-536)
[    6.697878] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.LPTE._STA] (Node ffff880222065e38), AE_ALREADY_EXISTS (20120320/psparse-536)
[    6.697884] ACPI Error: Method execution failed [\_SB_.PCI0.LPCB.LPTE._STA] (Node ffff880222065e38), AE_ALREADY_EXISTS (20120320/uteval-103)
[    6.735482] ACPI: Marking method CLPS as Serialized because of AE_ALREADY_EXISTS error
[    6.741705] firewire_core 0000:0a:00.0: created device fw0: GUID 041baf01484fc000, S400
[    6.888106] parport_pc 00:08: activated
[    6.888112] parport_pc 00:08: reported by Plug and Play ACPI
[    6.899280] parport_pc 00:08: disabled
[    6.976879] ACPI: Battery Slot [BAT0] (battery present)
[    6.984864] ACPI: Battery Slot [BAT1] (battery absent)
[    6.995941] ACPI: Battery Slot [BAT2] (battery absent)
[    7.015489] iTCO_vendor_support: vendor-support=0
[    7.023380] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[    7.023458] iTCO_wdt: Found a Cougar Point TCO device (Version=2, TCOBASE=0x0460)
[    7.023476] iTCO_wdt: cannot register miscdev on minor=130 (err=-16)
[    7.023551] iTCO_wdt: probe of iTCO_wdt failed with error -16
[    7.055830] microcode: CPU0 sig=0x206a7, pf=0x10, revision=0x23
[    7.076648] Linux video capture interface: v2.00
[    7.098511] sdhci-pci 0000:0a:00.1: SDHCI controller found [1217:8321] (rev 5)
[    7.098565] sdhci-pci 0000:0a:00.1: Invalid iomem size. You may experience problems.
[    7.098739] Registered led device: mmc0::
[    7.124323] mmc0: SDHCI controller on PCI [0000:0a:00.1] using DMA
[    7.126604] i915 0000:00:02.0: setting latency timer to 64
[    7.134674] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_FHD (05ca:181c)
[    7.136509] input: Laptop_Integrated_Webcam_FHD as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.5/1-1.5:1.0/input/input9
[    7.136572] usbcore: registered new interface driver uvcvideo
[    7.136574] USB Video Class driver (1.1.1)
[    7.162672] i915 0000:00:02.0: irq 43 for MSI/MSI-X
[    7.162680] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[    7.162681] [drm] Driver supports precise vblank timestamp query.
[    7.162716] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[    7.170615] input: DualPoint Stick as /devices/platform/i8042/serio1/input/input10
[    7.183708] input: AlpsPS/2 ALPS DualPoint TouchPad as /devices/platform/i8042/serio1/input/input11
[    7.201619] microcode: CPU1 sig=0x206a7, pf=0x10, revision=0x23
[    7.201964] microcode: CPU2 sig=0x206a7, pf=0x10, revision=0x23
[    7.202235] microcode: CPU3 sig=0x206a7, pf=0x10, revision=0x23
[    7.202560] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    7.634857] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[    7.943584] fbcon: inteldrmfb (fb0) is primary device
[    8.341866] Console: switching to colour frame buffer device 240x67
[    8.346320] fb0: inteldrmfb frame buffer device
[    8.346322] drm: registered panic notifier
[    8.396447] acpi device:38: registered as cooling_device4
[    8.417899] ACPI: Video Device [VID] (multi-head: yes  rom: no  post: no)
[    8.418042] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input12
[    8.418288] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[    8.418542] snd_hda_intel 0000:00:1b.0: irq 44 for MSI/MSI-X
[    9.010633] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input13
[    9.044507] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14
[    9.044834] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input15
[    9.045006] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input16
[    9.045213] input: HDA Intel PCH Dock Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input17
[    9.045401] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input18
[    9.045590] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input19
[    9.045774] input: HDA Intel PCH Dock Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input20
[    9.851080] EXT4-fs (sda1): re-mounted. Opts: data=ordered
[    9.928398] Adding 2386636k swap on /dev/sda2.  Priority:-1 extents:1 across:2386636k 
[   11.335456] e1000e 0000:00:19.0: irq 41 for MSI/MSI-X
[   11.438143] e1000e 0000:00:19.0: irq 41 for MSI/MSI-X
[   11.439745] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   14.936033] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[   14.937523] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   29.456643] FS-Cache: Loaded
[   29.468431] RPC: Registered named UNIX socket transport module.
[   29.468434] RPC: Registered udp transport module.
[   29.468435] RPC: Registered tcp transport module.
[   29.468436] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   29.721322] NFS: Registering the id_resolver key type
[   29.721331] Key type id_resolver registered
[   29.721332] Key type id_legacy registered
[   29.721337] FS-Cache: Netfs 'nfs' registered for caching
[   33.850597] artha[673] trap int3 ip:7f677ddf45b1 sp:7fff0e664530 error:0
[   46.848189] EXT4-fs (sda1): re-mounted. Opts: data=ordered,commit=0
[ 5866.010937] warning: `VirtualBox' uses 32-bit capabilities (legacy support in use)
[ 5872.009504] EXT4-fs (sda1): Unaligned AIO/DIO on inode 4066605 by VirtualBox; performance will be poor.
[ 9832.630207] CPU3: Package power limit notification (total events = 1)
[ 9832.630209] CPU1: Package power limit notification (total events = 1)
[ 9832.630211] CPU2: Package power limit notification (total events = 1)
[ 9832.630213] CPU0: Package power limit notification (total events = 1)
[ 9832.641232] CPU1: Package power limit normal
[ 9832.641233] CPU3: Package power limit normal
[ 9832.641235] CPU2: Package power limit normal
[ 9832.641236] CPU0: Package power limit normal
[10723.881427] distort[7800]: segfault at 4 ip 0000000000403bd6 sp 00007fff79799000 error 4 in distort[400000+c000]
[11458.274361] usb 1-1.4: USB disconnect, device number 3
[11494.612382] Broadcom 43xx driver loaded [ Features: PMNLS ]
[11503.791968] usb 1-1.4: new full-speed USB device number 5 using ehci_hcd
[11512.094627] Broadcom 43xx driver loaded [ Features: PMNLS ]
[12174.162386] e1000e 0000:00:19.0: irq 41 for MSI/MSI-X
[12174.263349] e1000e 0000:00:19.0: irq 41 for MSI/MSI-X
[12174.264999] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[12176.810397] dell_wmi: Received unknown WMI event (0x0)
[12177.178734] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[12177.180274] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[12182.122084] dell_wmi: Received unknown WMI event (0x0)
[12626.796874] Broadcom 43xx-legacy driver loaded [ Features: PLID ]
[12991.850443] CPU3: Package power limit notification (total events = 2)
[12991.850445] CPU1: Package power limit notification (total events = 2)
[12991.850448] CPU2: Package power limit notification (total events = 2)
[12991.850450] CPU0: Package power limit notification (total events = 2)
[12991.861431] CPU3: Package power limit normal
[12991.861432] CPU1: Package power limit normal
[12991.861433] CPU2: Package power limit normal
[12991.861434] CPU0: Package power limit normal
[13536.099309] CPU1: Package power limit notification (total events = 5)
[13536.099311] CPU3: Package power limit notification (total events = 5)
[13536.099313] CPU2: Package power limit notification (total events = 5)
[13536.099314] CPU0: Package power limit notification (total events = 5)
[13536.110303] CPU3: Package power limit normal
[13536.110304] CPU2: Package power limit normal
[13536.110306] CPU1: Package power limit normal
[13536.110307] CPU0: Package power limit normal
[13895.513874] CPU2: Package power limit notification (total events = 11)
[13895.513877] CPU1: Package power limit notification (total events = 11)
[13895.513878] CPU3: Package power limit notification (total events = 11)
[13895.513880] CPU0: Package power limit notification (total events = 11)
[13895.524894] CPU3: Package power limit normal
[13895.524896] CPU2: Package power limit normal
[13895.524897] CPU1: Package power limit normal
[13895.524898] CPU0: Package power limit normal
[14195.076209] CPU3: Package power limit normal
[14195.076211] CPU2: Package power limit normal
[14195.076212] CPU1: Package power limit normal
[14195.076224] CPU0: Package power limit normal
[14554.525331] CPU2: Package power limit notification (total events = 44)
[14554.525334] CPU3: Package power limit notification (total events = 44)
[14554.525336] CPU1: Package power limit notification (total events = 44)
[14554.525338] CPU0: Package power limit notification (total events = 44)
[14554.529098] CPU2: Package power limit normal
[14554.529099] CPU1: Package power limit normal
[14554.529100] CPU3: Package power limit normal
[14554.529101] CPU0: Package power limit normal
[16505.674767] Broadcom 43xx driver loaded [ Features: PMNLS ]
[18154.234396] CPU2: Package power limit notification (total events = 54)
[18154.234399] CPU1: Package power limit notification (total events = 54)
[18154.234400] CPU3: Package power limit notification (total events = 54)
[18154.234402] CPU0: Package power limit notification (total events = 54)
[18154.234838] CPU2: Package power limit normal
[18154.234839] CPU1: Package power limit normal
[18154.234839] CPU3: Package power limit normal
[18154.234841] CPU0: Package power limit normal
[18633.518551] CPU2: Package power limit notification (total events = 64)
[18633.518554] CPU3: Package power limit notification (total events = 64)
[18633.518555] CPU1: Package power limit notification (total events = 64)
[18633.518557] CPU0: Package power limit notification (total events = 64)
[18633.529543] CPU3: Package power limit normal
[18633.529545] CPU1: Package power limit normal
[18633.529547] CPU2: Package power limit normal
[18633.529548] CPU0: Package power limit normal

Offline

#5 2012-09-03 11:43:48

Gusar
Member
Registered: 2009-08-25
Posts: 3,431

Re: b43 module wont load wlan interface

kayaman wrote:

as i said i tried wl already and it doesnt work at all hmm

That's not a useful bug report. Install the driver, modprobe the wl module, then check dmesg.

Last edited by Gusar (2012-09-03 11:45:36)

Offline

#6 2012-09-03 11:54:22

kayaman
Member
Registered: 2012-09-03
Posts: 10

Re: b43 module wont load wlan interface

Gusar wrote:
kayaman wrote:

as i said i tried wl already and it doesnt work at all hmm

That's not a useful bug report. Install the driver, modprobe the wl module, then check dmesg.

well then i wouldn't be able to post anything cause my eth0 driver wont even load ^^, still b43 is the newer module?
i think its a much more common error. mybe i forgot something hmm

Offline

#7 2012-09-03 12:30:37

Gusar
Member
Registered: 2009-08-25
Posts: 3,431

Re: b43 module wont load wlan interface

kayaman wrote:

well then i wouldn't be able to post anything cause my eth0 driver wont even load ^^

Err, why would installing the wl driver interfere with eth0? Ok, there's the possibility that wl loads first, in which case wireless would be eth0 and wired would be eth1. Search the wiki for persistent network names.

kayaman wrote:

still b43 is the newer module?

I don't know what you mean here. b43 is a driver. wl is another driver. b43 doesn't support your wifi card, wl does.

Offline

#8 2012-09-04 07:46:37

kayaman
Member
Registered: 2012-09-03
Posts: 10

Re: b43 module wont load wlan interface

well i tried again wl and this time i got eth0 and a eth1 running smile
ty for "encouraging" me to try it again.

Offline

#9 2012-09-04 10:25:26

nomorewindows
Member
Registered: 2010-04-03
Posts: 2,976

Re: b43 module wont load wlan interface

You need to install fw-cutter to grab the firmware.


I may have to CONSOLE you about your usage of ridiculously easy graphical interfaces...
Look ma, no mouse.

Offline

#10 2012-09-05 23:47:58

nomorewindows
Member
Registered: 2010-04-03
Posts: 2,976

Re: b43 module wont load wlan interface

Kernel 3.5.3-1 and b43 even with firmware isn't connecting to wireless routers.  Rolling back to a previous kernel 3.4.9, with restored operation.


I may have to CONSOLE you about your usage of ridiculously easy graphical interfaces...
Look ma, no mouse.

Offline

#11 2012-09-06 07:25:00

marko2010
Member
Registered: 2010-04-17
Posts: 66

Re: b43 module wont load wlan interface

nomorewindows wrote:

Kernel 3.5.3-1 and b43 even with firmware isn't connecting to wireless routers.

I have a Broadcom wireless card that uses the b43 firmware and its connecting just fine with the 3.5.3-1 kernel. I'm using netcfg to manage the connection.

Offline

#12 2012-09-07 21:35:13

nomorewindows
Member
Registered: 2010-04-03
Posts: 2,976

Re: b43 module wont load wlan interface

I'm using wicd and I couldn't get 3.5.3-1 to connect to anything.  I first thought it was the commercial cisco routers, and then it wouldn't connect to anything.  It sees all of the wireless stations, but it won't hold a connection, immediately dropping.


I may have to CONSOLE you about your usage of ridiculously easy graphical interfaces...
Look ma, no mouse.

Offline

#13 2012-11-26 19:36:57

lspci
Member
From: Virginia, USA
Registered: 2012-06-09
Posts: 242

Re: b43 module wont load wlan interface

Have you tried using this?  Broadcom Linux Drivers

I also have a Broadcom wireless adapter and would be using the drivers from the above website, but I couldn't figure out how to get them to work.  You have to compile them in a Linux 2.6 environment, so I used virtualbox and the 2009 release media for Arch Linux and managed to get it to compile, but once I compiled it I couldn't figure out how to load the modules.  Modprobing and insmoding didn't seem to work.  So I'm not really sure if this will be helpful or not, but the drivers on the site are supposed to be for BCM43228 64bit and/or 32bit. 

$ lspci | grep BCM43
03:00.0 Network controller: Broadcom Corporation BCM43228 802.11a/b/g/n

I could upload the compiled files to a git repo and make a PKGBUILD for them, I guess, but I have no idea what to do with the files now that they have compiled. 

$ ls
built-in.o  lib  Makefile  modules.order  Module.symvers src  sta  wl.ko  wl.mod.c  wl.mod.o  wl.o

Please don't be a help vampire. | Bitbucket

Give a little more for a little less today.  smile

Offline

#14 2012-11-26 21:03:36

10PinkPanther
Member
From: Croatia
Registered: 2012-11-10
Posts: 333

Re: b43 module wont load wlan interface

I have broadcom 4312 with b43,b43-fwcutter and b43-firmware.Works fine on all kernels.Fwcutter has to be installed before firmware.Wired and wireless works perfectly for me with netcfg and wpa_supplicant and I've enabled net-auto-wireless.All learned from the wiki.But for my card b43 is the only option.

Offline

#15 2012-12-07 14:43:04

lspci
Member
From: Virginia, USA
Registered: 2012-06-09
Posts: 242

Re: b43 module wont load wlan interface

kayaman wrote:

well i tried again wl and this time i got eth0 and a eth1 running smile
ty for "encouraging" me to try it again.

Marked this as solved if your problem has been resolved then. 

( I got my eth1 working by installing broadcom-wl, which I copied from a liveCD for ArchBang So, I'm good.)


Please don't be a help vampire. | Bitbucket

Give a little more for a little less today.  smile

Offline

Board footer

Powered by FluxBB