You are not logged in.

#1 2012-10-17 02:37:38

ilkyest
Member
From: Brazil
Registered: 2010-02-13
Posts: 269

Printer problems - again fighting with my p1005 [solved]

Pals. I were fighting about 3 weeks. First to install without AIF

done

after to let all ok

done

and now, with my p1005 printer
What happens. The firmware isn't loaded. If I go to windows, print something, return to linux, and put something to print, I can print a lot

It I put the printer off, and on again nothing more about printing.

When you switch on the printer, on normal ways it works twice. After on, and about 3 or 4 seconds after it, that is when firmware are loaded.

I've installed it with foo2zjs, that were the way I've used last time. Compiled it with pkg and install with pacman -U

localhost:631 shows "sending data to printer" but nothing happens. If I go, and came back from windows, sending data to printer, and printer prints...... until switch off again

[  136.822503] usblp0: removed
[  170.701302] usblp 3-4:1.0: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x03F0 pid 0x3D17

after print something on linux

[  136.822503] usblp0: removed
[  170.701302] usblp 3-4:1.0: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x03F0 pid 0x3D17
[  589.263983] usblp0: removed
[  590.169775] usblp 3-4:1.0: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x03F0 pid 0x3D17

reading about something on wiki, it says about hp-firmware -n, but this weren't found

hplip doesn't installs firmware (hp plugin install failed) and I couldn't ever install it, but had ever worked with foo2zjs

Last edited by ilkyest (2012-11-15 15:04:04)

Offline

#2 2012-10-17 15:48:31

ilkyest
Member
From: Brazil
Registered: 2010-02-13
Posts: 269

Re: Printer problems - again fighting with my p1005 [solved]

more try

modprobe usblp
rmmod usblp
modprobe usbcore
/etc/rc.d/cupsd restart

nothing helps yet

Offline

#3 2012-10-17 18:03:36

dare023
Member
Registered: 2010-04-21
Posts: 64

Re: Printer problems - again fighting with my p1005 [solved]

I have same printer.Just use foo2zjs driver.There are more themes about it,it used to work nicely but not with latest versions of hplip.

Offline

#4 2012-10-17 22:11:26

ilkyest
Member
From: Brazil
Registered: 2010-02-13
Posts: 269

Re: Printer problems - again fighting with my p1005 [solved]

don't work to me....

Offline

#5 2012-10-18 17:01:24

dare023
Member
Registered: 2010-04-21
Posts: 64

Re: Printer problems - again fighting with my p1005 [solved]

That is strange.Did you install from aur?This one was always working,with some small issues.

Offline

#6 2012-10-18 21:34:45

ilkyest
Member
From: Brazil
Registered: 2010-02-13
Posts: 269

Re: Printer problems - again fighting with my p1005 [solved]

yeah. I've installed from aur. first by yaourt, after, downloading and makepkg

I don't know how could I restart from begin with all, without install all arch

Offline

#7 2012-10-22 21:00:22

issproevolution
Member
Registered: 2007-04-15
Posts: 7

Re: Printer problems - again fighting with my p1005 [solved]

ilkyest wrote:

I don't know how could I restart from begin with all, without install all arch

I just installed arch from scratch now and I have the same problem, and I have the same printer: HP p1005.
I try install the printer in cups with foo2zjs's driver, with hplip, with hpcups but it doesn't work.. I try to print the test page and in all case that I write before, cups says "job complete" but the printer don't work..
Which is the problem?
thanks a lot!!

Offline

#8 2012-11-15 15:03:30

ilkyest
Member
From: Brazil
Registered: 2010-02-13
Posts: 269

Re: Printer problems - again fighting with my p1005 [solved]

Ok pals. After go to fedora, I should, again, return back to my dear arch. I`ve used the helmuthdu script, and  taaaaaaaadaaaaaaaaaaaaaaaa

even without installing the printer the firmware uploads...... (two working after turns on the device)

So, I think that the script installed something more than I tried first time. And so.... who can`t make it work, install de base system as wiki says, after, download the script, and make it work.
I haven`t installed the ATI driver by the script, but a big part of programs I use, I`ve installed by that script

If someone want try

conect to internet
install base and base-devel
logged as root

Install git: `pacman -Sy git`
- get it: `git clone git://github.com/helmuthdu/aui`
- run it: `cd aui && ./aui`

I haven`t installed base system by this script. I have installed base system by wiki way

Offline

#9 2012-11-15 18:12:59

dare023
Member
Registered: 2010-04-21
Posts: 64

Re: Printer problems - again fighting with my p1005 [solved]

Did you try to print some tables from calc or pdf?My printer was always working,just cannot get to print table borders,don't know why..

Offline

Board footer

Powered by FluxBB