You are not logged in.
Pals. I were fighting about 3 weeks. First to install without AIF
done
after to let all ok
done
and now, with my p1005 printer
What happens. The firmware isn't loaded. If I go to windows, print something, return to linux, and put something to print, I can print a lot
It I put the printer off, and on again nothing more about printing.
When you switch on the printer, on normal ways it works twice. After on, and about 3 or 4 seconds after it, that is when firmware are loaded.
I've installed it with foo2zjs, that were the way I've used last time. Compiled it with pkg and install with pacman -U
localhost:631 shows "sending data to printer" but nothing happens. If I go, and came back from windows, sending data to printer, and printer prints...... until switch off again
[ 136.822503] usblp0: removed
[ 170.701302] usblp 3-4:1.0: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x03F0 pid 0x3D17
after print something on linux
[ 136.822503] usblp0: removed
[ 170.701302] usblp 3-4:1.0: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x03F0 pid 0x3D17
[ 589.263983] usblp0: removed
[ 590.169775] usblp 3-4:1.0: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x03F0 pid 0x3D17
reading about something on wiki, it says about hp-firmware -n, but this weren't found
hplip doesn't installs firmware (hp plugin install failed) and I couldn't ever install it, but had ever worked with foo2zjs
Last edited by ilkyest (2012-11-15 15:04:04)
Offline
more try
modprobe usblp
rmmod usblp
modprobe usbcore
/etc/rc.d/cupsd restart
nothing helps yet
Offline
I have same printer.Just use foo2zjs driver.There are more themes about it,it used to work nicely but not with latest versions of hplip.
Offline
don't work to me....
Offline
That is strange.Did you install from aur?This one was always working,with some small issues.
Offline
yeah. I've installed from aur. first by yaourt, after, downloading and makepkg
I don't know how could I restart from begin with all, without install all arch
Offline
I don't know how could I restart from begin with all, without install all arch
I just installed arch from scratch now and I have the same problem, and I have the same printer: HP p1005.
I try install the printer in cups with foo2zjs's driver, with hplip, with hpcups but it doesn't work.. I try to print the test page and in all case that I write before, cups says "job complete" but the printer don't work..
Which is the problem?
thanks a lot!!
Offline
Ok pals. After go to fedora, I should, again, return back to my dear arch. I`ve used the helmuthdu script, and taaaaaaaadaaaaaaaaaaaaaaaa
even without installing the printer the firmware uploads...... (two working after turns on the device)
So, I think that the script installed something more than I tried first time. And so.... who can`t make it work, install de base system as wiki says, after, download the script, and make it work.
I haven`t installed the ATI driver by the script, but a big part of programs I use, I`ve installed by that script
If someone want try
conect to internet
install base and base-devel
logged as root
Install git: `pacman -Sy git`
- get it: `git clone git://github.com/helmuthdu/aui`
- run it: `cd aui && ./aui`
I haven`t installed base system by this script. I have installed base system by wiki way
Offline
Did you try to print some tables from calc or pdf?My printer was always working,just cannot get to print table borders,don't know why..
Offline