You are not logged in.

#1 2013-01-22 16:09:26

pesh1983
Member
Registered: 2012-08-30
Posts: 8

After exit from suspend mode cpu cooler running very fast

Hi everybody! I have a problem when exit from suspend mode on my desktop. My cooler starts running very fast and don't stop after time. If I reboot it's running very quiet. How can I solve this problem? Any suggestions? Thanks.

Offline

#2 2013-01-22 19:00:58

boris220
Member
Registered: 2013-01-21
Posts: 5

Re: After exit from suspend mode cpu cooler running very fast

Hey! Perhaps this is helping you: https://bugs.archlinux.org/task/32025

Offline

#3 2013-01-23 03:50:29

reasterling
Member
Registered: 2012-09-01
Posts: 8

Re: After exit from suspend mode cpu cooler running very fast

Hello pesh1983,
I believe that I am having the same problem.

before suspend:

cheap% sensors
acpitz-virtual-0
Adapter: Virtual device
temp1:        +46.0°C  (crit = +256.0°C)
temp2:        +50.0°C  (crit = +105.0°C)
temp3:        +45.0°C  (crit = +105.0°C)
temp4:        +32.0°C  (crit = +105.0°C)
temp5:         +0.0°C  (crit = +110.0°C)

coretemp-isa-0000
Adapter: ISA adapter
Core 0:       +55.0°C  (high = +100.0°C, crit = +100.0°C)
Core 1:       +55.0°C  (high = +100.0°C, crit = +100.0°C)

After suspend:

cheap% sensors
acpitz-virtual-0
Adapter: Virtual device
temp1:        +55.0°C  (crit = +256.0°C)
temp2:        +47.0°C  (crit = +105.0°C)
temp3:        +45.0°C  (crit = +105.0°C)
temp4:        +32.0°C  (crit = +105.0°C)
temp5:        +90.0°C  (crit = +110.0°C)

coretemp-isa-0000
Adapter: ISA adapter
Core 0:       +51.0°C  (high = +100.0°C, crit = +100.0°C)
Core 1:       +52.0°C  (high = +100.0°C, crit = +100.0°C)

I am confident that temp5 is not 90 degrees.  After suspend my system fan runs non-stop.  I edited /etc/sensors3.conf and added the lines to ignore temp5.  Now sensors will not show output for temp5, but my fan still runs all the time after resume.

Offline

#4 2013-01-23 17:38:43

mich41
Member
Registered: 2012-06-22
Posts: 592

Re: After exit from suspend mode cpu cooler running very fast

On most desktop motherboards, fans are controlled by SuperIO chip which is also connected to few temperature sensors deployed on the motherboard. Typical SuperIO can be configured to run each fan at constant speed or to vary its speed according to some temperature input, e.g. CPU fan can be controlled by thermal sensor installed under CPU socket.

This configuration is performed by BIOS during boot-up. OS's have little control over this part of SuperIO because it's often accessed concurrently by ACPI code (e.g. this ACPI temperature reader you have). This means that post-suspend restoration of fan settings needs to be performed by BIOS, before resuming the OS. However, BIOSes are the most buggy pieces of software ever seen on this planet, so ...

Your options are:
1. Try modprobe fan and see if there is some ACPI interface for controlling the fans manually. Probably there's none.
2. If the problem happens after hibernation (not sleep), try hibernating with echo shutdown >/sys/power/disk ; echo disk >/sys/power/state . This will run normal "shutdown" ACPI code after hibernating and will trick the BIOS to perform full power-on procedure when you turn the machine on again, including SuperIO configuration.
3. Update BIOS.
4. Complain to your motherboard's vendor smile
5. Boot with acpi_enforce_resources=lax and run sensors-detect to find out if there is a Linux driver for your SuperIO. This will give you manual control over SuperIO configuration at the cost of potential problems if ACPI code and linux driver ever decide to poke SuperIO registers at the same time.

Last edited by mich41 (2013-01-23 17:41:15)

Offline

#5 2013-01-23 17:48:59

reasterling
Member
Registered: 2012-09-01
Posts: 8

Re: After exit from suspend mode cpu cooler running very fast

mich41,
Thank you for your reply.  I am still trying to fix this.  It is interesting that this started the first time I boot to the 3.7.3 kernel.  I suspect that this is caused by a change in software/config.  I will try to roll back to my previous kernel when I get some time this evening to see if that will resolve the problem.

cheap% uname -a
Linux cheap 3.7.3-1-ARCH #1 SMP PREEMPT Thu Jan 17 18:52:30 CET 2013 x86_64 GNU/Linux

Offline

#6 2013-01-25 01:54:10

reasterling
Member
Registered: 2012-09-01
Posts: 8

Re: After exit from suspend mode cpu cooler running very fast

This is very frustrating.  It would seem that this is a known bug with the 3.7.* kernels.  So far there is no fix except to run an older kernel.

Offline

#7 2013-01-25 02:02:28

WonderWoofy
Member
From: Los Gatos, CA
Registered: 2012-05-19
Posts: 8,412

Re: After exit from suspend mode cpu cooler running very fast

Known bug?  Did you find a bug report or something?  I'm not trying to say you're wrong, I a genuinely interested.

Offline

#8 2013-01-25 22:16:27

reasterling
Member
Registered: 2012-09-01
Posts: 8

Re: After exit from suspend mode cpu cooler running very fast

Did you find a bug report or something?

Yes, I found "something".
https://lkml.org/lkml/2012/12/19/166

Offline

#9 2013-01-28 18:13:15

GNRS
Member
Registered: 2012-12-27
Posts: 3

Re: After exit from suspend mode cpu cooler running very fast

Same problem here... Any news on this issue?

Linux arch 3.7.4-1-ARCH #1 SMP PREEMPT Mon Jan 21 23:05:29 CET 2013 x86_64 GNU/Linux

Last edited by GNRS (2013-01-28 18:14:26)

Offline

#10 2013-01-29 05:15:26

reasterling
Member
Registered: 2012-09-01
Posts: 8

Re: After exit from suspend mode cpu cooler running very fast

GNRS,

I Still have this problem with the latest kernel.  However, I am able to use my laptop (HP tc4400) without this problem by using the LTS kernel provided through pacman.

# pacman -S linux-lts linux-lts-headers

To be able to boot the "new" old kernel, you will need to regenerate your grub.cfg file.

# cp /boot/grub/grub.cfg /boot/grub/grub.cfg.backup
# grub-mkconfig -o /boot/grub/grub.cfg

On my system this generated 4 boot enteries in grub.  Two for the LTS kernel (default), and two for the original latest kernel.

My system is currently running the LTS kernel without any problems.

cheap% uname -a
Linux cheap 3.0.60-1-lts #1 SMP Mon Jan 21 22:58:04 CET 2013 x86_64 GNU/Linux

I hope this helps you and I hope this problem gets resolved soon.

Last edited by reasterling (2013-01-29 05:26:21)

Offline

#11 2013-02-12 08:22:39

Yagi858
Member
Registered: 2008-12-17
Posts: 31

Re: After exit from suspend mode cpu cooler running very fast

I confirm the bug. I had this problem also with linux-lqx since 3.7.1 and now with the core kernel, so I am sure this is a regression on 3.7.* kernel. However if not suspended the kernel is usable as well.

Offline

#12 2013-02-12 16:21:44

mini
Member
Registered: 2006-12-18
Posts: 132

Re: After exit from suspend mode cpu cooler running very fast

Is the any solution in this case. My fan running very fast after hibernation.
My option is to hibernate with
echo shutdown >/sys/power/disk ; echo disk >/sys/power/state
but i can do it temporarily.
Is it any way to put this script in /usr/lib/pm-utils/module.d/hibernate?

Offline

#13 2013-02-14 18:18:47

tekstryder
Member
Registered: 2013-02-14
Posts: 19

Re: After exit from suspend mode cpu cooler running very fast

What graphics hardware are you using? I was experiencing this with my nVidia GPU. The fix in this post is specific to nVidia hardware and the nouveau driver.

I recently bisected nouveau git master upon realizing fan control is busted with newer kernels (3.3+) and could no longer control my GTX 260 (nv50 gpu) fan. When resuming from suspend, the fan would run at full speed. Loud and unnecessary!

Here's my bug report and patch: https://bugs.freedesktop.org/show_bug.cgi?id=60704

Note: due to restructuring of the nouveau driver in recent kernels there are separate patches for 3.4.x series and 3.7.x. I applied against 3.4.30 and can confirm it resolves the problem. I've ported the patch for upstream stable 3.7.x and git master 3.8-rc7. After building all 3 aforementioned kernels patched, sensors detect my fan controller successfully. Peace and quiet has been restored!

I am hoping to see this merged into stable!

Offline

#14 2013-02-14 19:03:08

mini
Member
Registered: 2006-12-18
Posts: 132

Re: After exit from suspend mode cpu cooler running very fast

My graphic is Radeon X2300.
I am not sure what kind of patch I have to use (seek).

Offline

#15 2013-02-18 08:40:12

Yagi858
Member
Registered: 2008-12-17
Posts: 31

Re: After exit from suspend mode cpu cooler running very fast

I have nVidia GTX275 and I used nuveau-dri since ten months ago. I didn't have this issue with 3.6.* kernel. I will try to downgrade kernel so to confirm this.

Offline

#16 2013-03-01 01:15:23

Aroko
Member
Registered: 2012-03-29
Posts: 4

Re: After exit from suspend mode cpu cooler running very fast

Hi guys, I have same symptoms, but my graphics is an integrated intel.

Offline

#17 2013-03-01 02:18:38

frank604
Member
From: BC, Canada
Registered: 2011-04-20
Posts: 966
Website

Re: After exit from suspend mode cpu cooler running very fast

Same bug as 32025.  Same as https://bbs.archlinux.org/viewtopic.php?id=158465
Basically, the bug report has a fix.  Use lts kernel or manually install kernel 3.8+

Last edited by frank604 (2013-03-01 02:20:04)


github       bible       blog

Offline

#18 2013-03-03 18:08:48

Tuxe
Member
From: Finland
Registered: 2005-02-28
Posts: 8
Website

Re: After exit from suspend mode cpu cooler running very fast

Hello,

I have the same problem on my HP ProBook 5310m laptop. I run the following after resume from suspend to fix the fan speed:

for i in {1..15}; do echo 0 > /sys/class/thermal/cooling_device$i/cur_state; done
echo 1 > /sys/class/thermal/cooling_device15/cur_state

If you have a different machine, you may need to change which cooling_devices you tinker with. Check the correct values after a reboot when the fan is running at the correct speed.

Offline

#19 2013-03-12 08:49:54

Yagi858
Member
Registered: 2008-12-17
Posts: 31

Re: After exit from suspend mode cpu cooler running very fast

frank604 wrote:

Same bug as 32025.  Same as https://bbs.archlinux.org/viewtopic.php?id=158465
Basically, the bug report has a fix.  Use lts kernel or manually install kernel 3.8+

Lts kernel is OK and for me this is just a trick, it is not a fix. The bug is still present on 3.8.+ (from testing at moment) kernel. My hardware as wrote before is GTX275 with nouveau.

Last edited by Yagi858 (2013-03-12 10:39:57)

Offline

#20 2013-03-20 16:11:34

lfxgroove
Member
Registered: 2012-05-10
Posts: 13

Re: After exit from suspend mode cpu cooler running very fast

Having this problem aswell with 3.8.3 from stable, will try the echo fix and see if it works for me.

Offline

#21 2013-03-20 19:02:54

cris9288
Member
Registered: 2013-01-07
Posts: 347

Re: After exit from suspend mode cpu cooler running very fast

I just started having this problem after upgrading to 3.8.3-2 from 3.7.10. Of course, I didn't suspend for some time after I upgrade so I already cleared my cache. Hope someone finds a fix. I'm seeing this pop up in dmesg, but I don't know if it's related or if it was there before

$ dmesg | grep Warning
[    6.270643] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \PMIO 1 (20121018/utaddress-251)
[    6.270650] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \_SB_.PCI0.LPCB.PMBS 2 (20121018/utaddress-251)
[    6.270658] ACPI Warning: 0x0000000000000740-0x000000000000074f SystemIO conflicts with Region \GPIO 1 (20121018/utaddress-251)
[    6.270662] ACPI Warning: 0x0000000000000730-0x000000000000073f SystemIO conflicts with Region \GPIO 1 (20121018/utaddress-251)
[    6.270665] ACPI Warning: 0x0000000000000730-0x000000000000073f SystemIO conflicts with Region \_SB_.PCI0.LPCB.GPIO 2 (20121018/utaddress-251)
[    6.270669] ACPI Warning: 0x0000000000000700-0x000000000000072f SystemIO conflicts with Region \GPIO 1 (20121018/utaddress-251)
[    6.270674] ACPI Warning: 0x0000000000000700-0x000000000000072f SystemIO conflicts with Region \_SB_.PCI0.LPCB.GPIO 2 (20121018/utaddress-251)
[    6.549609] ACPI Warning: 0x0000000000004040-0x000000000000405f SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20121018/utaddress-251)

Offline

#22 2013-03-21 14:24:48

mich41
Member
Registered: 2012-06-22
Posts: 592

Re: After exit from suspend mode cpu cooler running very fast

Are you booting with acpi_enforce_resources set to 'no' or 'lax'? What's printed immediately before and after these warnings?

What modules are loaded?

Offline

#23 2013-03-21 18:15:52

cris9288
Member
Registered: 2013-01-07
Posts: 347

Re: After exit from suspend mode cpu cooler running very fast

Here's a more complete output. For what it's worth, the reported behavior stopped on my machine once I removed laptop-mode-tools. I replaced it with powerdown, but i don't think that's relevant.

$ dmesg | grep -A 5 -B 5 Warning

[    6.177445] ACPI: Power Button [PWRF]
[    6.178998] thermal LNXTHERM:00: registered as thermal_zone0
[    6.179001] ACPI: Thermal Zone [TZ00] (33 C)
[    6.179633] thermal LNXTHERM:01: registered as thermal_zone1
[    6.179636] ACPI: Thermal Zone [TZ01] (0 C)
[    6.215316] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \PMIO 1 (20121018/utaddress-251)
[    6.215324] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \_SB_.PCI0.LPCB.PMBS 2 (20121018/utaddress-251)
[    6.215327] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    6.215331] ACPI Warning: 0x0000000000000740-0x000000000000074f SystemIO conflicts with Region \GPIO 1 (20121018/utaddress-251)
[    6.215334] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    6.215336] ACPI Warning: 0x0000000000000730-0x000000000000073f SystemIO conflicts with Region \GPIO 1 (20121018/utaddress-251)
[    6.215339] ACPI Warning: 0x0000000000000730-0x000000000000073f SystemIO conflicts with Region \_SB_.PCI0.LPCB.GPIO 2 (20121018/utaddress-251)
[    6.215341] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    6.215343] ACPI Warning: 0x0000000000000700-0x000000000000072f SystemIO conflicts with Region \GPIO 1 (20121018/utaddress-251)
[    6.215345] ACPI Warning: 0x0000000000000700-0x000000000000072f SystemIO conflicts with Region \_SB_.PCI0.LPCB.GPIO 2 (20121018/utaddress-251)
[    6.215348] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    6.215349] lpc_ich: Resource conflict(s) found affecting gpio_ich
[    6.285009] ACPI: AC Adapter [AC] (off-line)
[    6.286120] cfg80211: Calling CRDA to update world regulatory domain
[    6.341485] atl1c 0000:08:00.0: version 1.0.1.1-NAPI
[    6.389512] wmi: Mapper loaded
[    6.540828] ACPI: Requesting acpi_cpufreq
[    6.582939] ACPI Warning: 0x0000000000004040-0x000000000000405f SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20121018/utaddress-251)
[    6.582946] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    6.621268] lib80211: common routines for IEEE802.11 drivers
[    6.621271] lib80211_crypt: registered algorithm 'NULL'
[    6.680311] mei 0000:00:16.0: setting latency timer to 64
[    6.680386] mei 0000:00:16.0: irq 41 for MSI/MSI-X

Again, not sure if this will help solve anything. I no longer have the fan control problem and am still getting these warnings.

here's lsmod

Module                  Size  Used by
msr                     2704  0 
cpufreq_stats           3826  0 
michael_mic             2074  4 
arc4                    2007  2 
ecb                     2105  0 
cpufreq_powersave       1278  4 
snd_hda_codec_hdmi     27848  1 
snd_hda_codec_idt      55567  1 
joydev                  9727  0 
coretemp                6198  0 
kvm                   392222  0 
crc32c_intel           14313  0 
lib80211_crypt_tkip     9082  0 
acpi_cpufreq           10630  1 
mperf                   1267  1 acpi_cpufreq
ghash_clmulni_intel     4597  0 
cryptd                  8741  1 ghash_clmulni_intel
hp_accel               16520  0 
lis3lv02d              11603  1 hp_accel
hp_wmi                  8058  0 
snd_hda_intel          34194  0 
i915                  558806  2 
snd_hda_codec         102453  3 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel
wl                   2557001  0 
intel_agp              10872  1 i915
intel_gtt              12566  2 i915,intel_agp
snd_hwdep               6428  1 snd_hda_codec
snd_pcm                78146  3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel
drm_kms_helper         35517  1 i915
snd_page_alloc          7426  2 snd_pcm,snd_hda_intel
snd_timer              18934  1 snd_pcm
drm                   226103  3 i915,drm_kms_helper
snd                    60156  7 snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_hda_codec_idt,snd_pcm,snd_hda_codec,snd_hda_intel
i2c_algo_bit            5391  1 i915
iTCO_wdt                5447  0 
soundcore               5442  1 snd
iTCO_vendor_support     1929  1 iTCO_wdt
microcode              14465  0 
psmouse                76175  0 
mei                    59991  0 
lib80211                3949  2 wl,lib80211_crypt_tkip
i2c_i801               11077  0 
i2c_core               23171  5 drm,i915,i2c_i801,drm_kms_helper,i2c_algo_bit
evdev                  10136  11 
input_polldev           2914  1 lis3lv02d
sparse_keymap           3088  1 hp_wmi
processor              27431  1 acpi_cpufreq
serio_raw               5105  0 
wmi                     8379  1 hp_wmi
atl1c                  36302  0 
ac                      2568  0 
cfg80211              433688  1 wl
lpc_ich                11601  0 
thermal                 8577  0 
video                  11363  1 i915
button                  4701  1 i915
battery                 7098  0 
fan                     2785  0 
rfkill                 15996  3 cfg80211,hp_wmi
ext4                  478274  3 
crc16                   1359  1 ext4
jbd2                   77917  1 ext4
mbcache                 6026  1 ext4
sr_mod                 14823  0 
cdrom                  35520  1 sr_mod
sd_mod                 31258  4 
ahci                   22160  3 
libahci                20906  1 ahci
libata                168683  2 ahci,libahci
ehci_pci                4120  0 
ehci_hcd               47423  1 ehci_pci
sdhci_pci              11412  0 
sdhci                  28375  1 sdhci_pci
scsi_mod              130797  3 libata,sd_mod,sr_mod
mmc_core               91956  2 sdhci,sdhci_pci
usbcore               175061  2 ehci_hcd,ehci_pci
usb_common               954  1 usbcore

and kernel parameter

 GRUB_CMDLINE_LINUX_DEFAULT="quiet nmi_watchdog=0" 

Offline

#24 2013-03-21 20:02:31

mich41
Member
Registered: 2012-06-22
Posts: 592

Re: After exit from suspend mode cpu cooler running very fast

These warnings indicate that some driver wanted to access some device which is already controlled by ACPI.

They are harmless, but if you were booting with acpi_enforce_resources disabled they would get ignored and the conflicting driver would get enabled anyway.

Offline

#25 2013-04-02 20:33:19

koshak
Member
Registered: 2013-03-13
Posts: 35

Re: After exit from suspend mode cpu cooler running very fast

Tuxe wrote:

Hello,

I have the same problem on my HP ProBook 5310m laptop. I run the following after resume from suspend to fix the fan speed:

for i in {1..15}; do echo 0 > /sys/class/thermal/cooling_device$i/cur_state; done
echo 1 > /sys/class/thermal/cooling_device15/cur_state

If you have a different machine, you may need to change which cooling_devices you tinker with. Check the correct values after a reboot when the fan is running at the correct speed.

That really helps!

Before suspend I have

mininote ~ % for i in {0..9};do echo "/sys/class/thermal/cooling_device$i"; cat /sys/class/thermal/cooling_device$i/cur_state; done
/sys/class/thermal/cooling_device0
0
/sys/class/thermal/cooling_device1
0
/sys/class/thermal/cooling_device2
0
/sys/class/thermal/cooling_device3
0
/sys/class/thermal/cooling_device4
0
/sys/class/thermal/cooling_device5
0
/sys/class/thermal/cooling_device6
1
/sys/class/thermal/cooling_device7
0
/sys/class/thermal/cooling_device8
0
/sys/class/thermal/cooling_device9
0

After resume from suspend:

mininote ~ % for i in {0..9};do echo "/sys/class/thermal/cooling_device$i"; cat /sys/class/thermal/cooling_device$i/cur_state; done
/sys/class/thermal/cooling_device0
1
/sys/class/thermal/cooling_device1
1
/sys/class/thermal/cooling_device2
1
/sys/class/thermal/cooling_device3
1
/sys/class/thermal/cooling_device4
1
/sys/class/thermal/cooling_device5
0
/sys/class/thermal/cooling_device6
1
/sys/class/thermal/cooling_device7
0
/sys/class/thermal/cooling_device8
0
/sys/class/thermal/cooling_device9
0

Here are events on suspend:

апр 03 00:08:02 mininote systemd-logind[263]: Lid closed.
апр 03 00:08:02 mininote systemd-logind[263]: Suspending...
апр 03 00:08:02 mininote systemd[1]: Starting Sleep.
апр 03 00:08:02 mininote systemd[1]: Reached target Sleep.
апр 03 00:08:02 mininote systemd[1]: Starting Suspend...
апр 03 00:08:02 mininote systemd-sleep[1655]: Suspending system...
апр 03 00:08:03 mininote kernel: PM: Syncing filesystems ... done.
апр 03 00:08:03 mininote kernel: PM: Preparing system for mem sleep
апр 03 00:08:16 mininote kernel: Freezing user space processes ... (elapsed 0.01 seconds) done.
апр 03 00:08:16 mininote systemd[1]: Time has been changed
апр 03 00:08:16 mininote systemd[1]: systemd-tmpfiles-clean.timer: time change, recalculating next elapse.

After resume from suspend:

апр 03 00:08:16 mininote systemd-logind[263]: Lid opened.
апр 03 00:08:16 mininote kernel: Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
апр 03 00:08:16 mininote kernel: PM: Entering mem sleep
апр 03 00:08:16 mininote kernel: Suspending console(s) (use no_console_suspend to debug)
апр 03 00:08:16 mininote kernel: sd 0:0:0:0: [sda] Synchronizing SCSI cache
апр 03 00:08:16 mininote kernel: sd 0:0:0:0: [sda] Stopping disk
апр 03 00:08:16 mininote kernel: e1000e 0000:00:19.0: System wakeup enabled by ACPI
апр 03 00:08:16 mininote kernel: snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D3hot
апр 03 00:08:16 mininote kernel: ACPI: Cannot transition to non-D0 state from D3
апр 03 00:08:16 mininote kernel: PM: suspend of devices complete after 564.432 msecs
апр 03 00:08:16 mininote kernel: PM: late suspend of devices complete after 0.488 msecs
апр 03 00:08:16 mininote kernel: ehci-pci 0000:00:1d.7: System wakeup enabled by ACPI
апр 03 00:08:16 mininote kernel: uhci_hcd 0000:00:1d.2: System wakeup enabled by ACPI
апр 03 00:08:16 mininote kernel: uhci_hcd 0000:00:1d.1: System wakeup enabled by ACPI
апр 03 00:08:16 mininote kernel: uhci_hcd 0000:00:1d.0: System wakeup enabled by ACPI
апр 03 00:08:16 mininote kernel: ehci-pci 0000:00:1a.7: System wakeup enabled by ACPI
апр 03 00:08:16 mininote kernel: uhci_hcd 0000:00:1a.1: System wakeup enabled by ACPI
апр 03 00:08:16 mininote kernel: uhci_hcd 0000:00:1a.0: System wakeup enabled by ACPI
апр 03 00:08:16 mininote kernel: PM: noirq suspend of devices complete after 38.190 msecs
апр 03 00:08:16 mininote kernel: ACPI: Preparing to enter system sleep state S3
апр 03 00:08:16 mininote kernel: PM: Saving platform NVS memory
апр 03 00:08:16 mininote kernel: Disabling non-boot CPUs ...
апр 03 00:08:16 mininote kernel: smpboot: CPU 1 is now offline
апр 03 00:08:16 mininote kernel: Extended CMOS year: 2000
апр 03 00:08:16 mininote kernel: ACPI: Low-level resume complete
апр 03 00:08:16 mininote kernel: PM: Restoring platform NVS memory
апр 03 00:08:16 mininote kernel: Extended CMOS year: 2000
апр 03 00:08:16 mininote kernel: CPU0: Thermal monitoring handled by SMI
апр 03 00:08:16 mininote kernel: Enabling non-boot CPUs ...
апр 03 00:08:16 mininote kernel: smpboot: Booting Node 0 Processor 1 APIC 0x1
апр 03 00:08:16 mininote kernel: Initializing CPU#1
апр 03 00:08:16 mininote kernel: CPU1: Thermal monitoring handled by SMI
апр 03 00:08:16 mininote kernel: CPU1 is up
апр 03 00:08:16 mininote kernel: ACPI: Waking up from system sleep state S3
апр 03 00:08:16 mininote kernel: uhci_hcd 0000:00:1a.0: System wakeup disabled by ACPI
апр 03 00:08:16 mininote kernel: uhci_hcd 0000:00:1a.1: System wakeup disabled by ACPI
апр 03 00:08:16 mininote kernel: ehci-pci 0000:00:1a.7: System wakeup disabled by ACPI
апр 03 00:08:16 mininote kernel: snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0
апр 03 00:08:16 mininote kernel: uhci_hcd 0000:00:1d.0: System wakeup disabled by ACPI
апр 03 00:08:16 mininote kernel: uhci_hcd 0000:00:1d.1: System wakeup disabled by ACPI
апр 03 00:08:16 mininote kernel: uhci_hcd 0000:00:1d.2: System wakeup disabled by ACPI
апр 03 00:08:16 mininote kernel: ehci-pci 0000:00:1d.7: System wakeup disabled by ACPI
апр 03 00:08:16 mininote kernel: PM: noirq resume of devices complete after 121.565 msecs
апр 03 00:08:16 mininote kernel: PM: early resume of devices complete after 0.381 msecs
апр 03 00:08:16 mininote kernel: i915 0000:00:02.0: setting latency timer to 64
апр 03 00:08:16 mininote kernel: ata_generic 0000:00:03.2: setting latency timer to 64
апр 03 00:08:16 mininote kernel: e1000e 0000:00:19.0: System wakeup disabled by ACPI
апр 03 00:08:16 mininote kernel: e1000e 0000:00:19.0: irq 42 for MSI/MSI-X
апр 03 00:08:16 mininote kernel: uhci_hcd 0000:00:1a.0: setting latency timer to 64
апр 03 00:08:16 mininote kernel: usb usb2: root hub lost power or was reset
апр 03 00:08:16 mininote systemd-sleep[1655]: System resumed.
апр 03 00:08:16 mininote kernel: uhci_hcd 0000:00:1a.1: setting latency timer to 64
апр 03 00:08:16 mininote kernel: usb usb3: root hub lost power or was reset
апр 03 00:08:16 mininote kernel: ehci-pci 0000:00:1a.7: setting latency timer to 64
апр 03 00:08:16 mininote kernel: snd_hda_intel 0000:00:1b.0: irq 43 for MSI/MSI-X
апр 03 00:08:16 mininote kernel: uhci_hcd 0000:00:1d.0: setting latency timer to 64
апр 03 00:08:16 mininote kernel: usb usb4: root hub lost power or was reset
апр 03 00:08:16 mininote kernel: uhci_hcd 0000:00:1d.1: setting latency timer to 64
апр 03 00:08:16 mininote kernel: usb usb5: root hub lost power or was reset
апр 03 00:08:16 mininote kernel: uhci_hcd 0000:00:1d.2: setting latency timer to 64
апр 03 00:08:16 mininote kernel: usb usb6: root hub lost power or was reset
апр 03 00:08:16 mininote kernel: ehci-pci 0000:00:1d.7: setting latency timer to 64
апр 03 00:08:16 mininote kernel: pci 0000:00:1e.0: setting latency timer to 64
апр 03 00:08:16 mininote kernel: ata_piix 0000:00:1f.1: setting latency timer to 64
апр 03 00:08:16 mininote kernel: ACPI Exception: AE_AML_PACKAGE_LIMIT, Index (0x0000000000000005) is beyond end of object (20121018/exoparg2-418)
апр 03 00:08:16 mininote kernel: ACPI Error: Method parse/execution failed [\_SB_.C2C3] (Node f5c32a38), AE_AML_PACKAGE_LIMIT (20121018/psparse-537)
апр 03 00:08:16 mininote kernel: ACPI Error: Method parse/execution failed [\_SB_.C003.C0F6.C3F3._STM] (Node f5c36dc8), AE_AML_PACKAGE_LIMIT (20121018/psparse-537)
апр 03 00:08:16 mininote kernel: ata1: ACPI set timing mode failed (status=0x300b)
апр 03 00:08:16 mininote kernel: ata2: port disabled--ignoring
апр 03 00:08:16 mininote kernel: psmouse serio1: hgpk: ID: 10 00 64
апр 03 00:08:16 mininote kernel: ata1.01: ACPI cmd ef/03:0c:00:00:00:b0 (SET FEATURES) filtered out
апр 03 00:08:16 mininote kernel: ata1.01: ACPI cmd ef/03:40:00:00:00:b0 (SET FEATURES) filtered out
апр 03 00:08:16 mininote kernel: ata1.00: ACPI cmd ef/03:01:00:00:00:a0 (SET FEATURES) filtered out
апр 03 00:08:16 mininote kernel: ata1.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
апр 03 00:08:16 mininote kernel: ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
апр 03 00:08:16 mininote kernel: ata1.00: ACPI cmd b1/c1:00:00:00:00:a0 (DEVICE CONFIGURATION OVERLAY) filtered out
апр 03 00:08:16 mininote kernel: ata1.00: ACPI cmd c6/00:10:00:00:00:a0 (SET MULTIPLE MODE) succeeded
апр 03 00:08:16 mininote kernel: ata1.00: configured for UDMA/100
апр 03 00:08:16 mininote kernel: ata1.01: configured for MWDMA2
апр 03 00:08:16 mininote kernel: sd 0:0:0:0: [sda] Starting disk
апр 03 00:08:16 mininote kernel: PM: resume of devices complete after 2786.068 msecs
апр 03 00:08:16 mininote kernel: PM: Finishing wakeup.
апр 03 00:08:16 mininote kernel: Restarting tasks ... done.
апр 03 00:08:16 mininote kernel: video LNXVIDEO:00: Restoring backlight state
апр 03 00:08:16 mininote systemd[1]: Started Suspend.
апр 03 00:08:16 mininote systemd[1]: Service sleep.target is not needed anymore. Stopping.
апр 03 00:08:16 mininote systemd[1]: Stopping Sleep.
апр 03 00:08:16 mininote systemd[1]: Stopped target Sleep.
апр 03 00:08:16 mininote systemd[1]: Starting Suspend.
апр 03 00:08:16 mininote systemd[1]: Reached target Suspend.
апр 03 00:08:16 mininote systemd-logind[263]: Operation finished.

Offline

Board footer

Powered by FluxBB