You are not logged in.

#1 2013-03-24 17:33:31

damdim
Member
Registered: 2010-03-13
Posts: 48

Hybrid graphics i915/radeon. Switch to radeon results to black screen

I have installed Arch Linux on a Dell Inspiron R15 with hybrid Intel/AMD graphics. vga_switcheroo is enabled and I can control radeon power with "echo ON/OFF > /sys/kernel/debug/vgaswitcheroo/switch".
But when I try to switch to radeon in console with "echo DIS > /sys/kernel/debug/vgaswitcheroo/switch" the screen turns off. I can switch back to intel with "echo IGD > /sys/kernel/debug/vgaswitcheroo/switch" by blind typing it, and then the screen turns back on.
Any ideas?

lspci

00:00.0 Host bridge: Intel Corporation 3rd Gen Core processor DRAM Controller (rev 09)
	Subsystem: Dell Device 0598
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: [e0] Vendor Specific Information: Len=0c <?>

00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port (rev 09) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=01, subordinate=06, sec-latency=0
	I/O behind bridge: 00003000-00003fff
	Memory behind bridge: c0000000-c0ffffff
	Prefetchable memory behind bridge: 00000000a0000000-00000000afffffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [88] Subsystem: Dell Device 0598
	Capabilities: [80] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee002f8  Data: 0000
	Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 256 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #2, Speed 5GT/s, Width x8, ASPM L0s L1, Latency L0 <256ns, L1 <8us
			ClockPM- Surprise- LLActRep- BwNot+
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled+ Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
			Slot #1, PowerLimit 75.000W; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
			Changed: MRL- PresDet+ LinkState-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported ARIFwd-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [100 v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
			Status:	NegoPending+ InProgress-
	Capabilities: [140 v1] Root Complex Link
		Desc:	PortNumber=02 ComponentID=01 EltType=Config
		Link0:	Desc:	TargetPort=00 TargetComponent=01 AssocRCRB- LinkType=MemMapped LinkValid+
			Addr:	00000000fed19000
	Kernel driver in use: pcieport

00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09) (prog-if 00 [VGA controller])
	Subsystem: Dell Device 0598
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 43
	Region 0: Memory at c1000000 (64-bit, non-prefetchable) [size=4M]
	Region 2: Memory at b0000000 (64-bit, prefetchable) [size=256M]
	Region 4: I/O ports at 4000 [size=64]
	Expansion ROM at <unassigned> [disabled]
	Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee00018  Data: 0000
	Capabilities: [d0] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [a4] PCI Advanced Features
		AFCap: TP+ FLR+
		AFCtrl: FLR-
		AFStatus: TP-
	Kernel driver in use: i915

00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04) (prog-if 30 [XHCI])
	Subsystem: Dell Device 0598
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 45
	Region 0: Memory at c1600000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: [70] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
		Address: 00000000fee00338  Data: 0000
	Kernel driver in use: xhci_hcd

00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04)
	Subsystem: Dell Device 0598
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 47
	Region 0: Memory at c1614000 (64-bit, non-prefetchable) [size=16]
	Capabilities: [50] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+
		Address: 00000000fee00398  Data: 0000
	Kernel driver in use: mei

00:1a.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) (prog-if 20 [EHCI])
	Subsystem: Dell Device 0598
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at c1619000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Debug port: BAR=1 offset=00a0
	Capabilities: [98] PCI Advanced Features
		AFCap: TP+ FLR+
		AFCtrl: FLR-
		AFStatus: TP-
	Kernel driver in use: ehci-pci

00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04)
	Subsystem: Dell Device 0598
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 50
	Region 0: Memory at c1610000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
		Address: 00000000fee00418  Data: 0000
	Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag- RBE- FLReset+
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
		LnkCap:	Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
			ClockPM- Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
	Capabilities: [100 v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=01
			Status:	NegoPending- InProgress-
		VC1:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=1 ArbSelect=Fixed TC/VC=22
			Status:	NegoPending- InProgress-
	Capabilities: [130 v1] Root Complex Link
		Desc:	PortNumber=0f ComponentID=00 EltType=Config
		Link0:	Desc:	TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+
			Addr:	00000000fed1c000
	Kernel driver in use: snd_hda_intel

00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
	I/O behind bridge: 00002000-00002fff
	Prefetchable memory behind bridge: 00000000c1400000-00000000c14fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
		LnkCap:	Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
			ClockPM- Surprise- LLActRep+ BwNot-
		LnkCtl:	ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
			Slot #0, PowerLimit 10.000W; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
			Changed: MRL- PresDet- LinkState+
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
		Address: 00000000  Data: 0000
	Capabilities: [90] Subsystem: Dell Device 0598
	Capabilities: [a0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: pcieport

00:1c.1 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 (rev c4) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
	Memory behind bridge: c1500000-c15fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
		LnkCap:	Port #2, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
			ClockPM- Surprise- LLActRep+ BwNot-
		LnkCtl:	ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
			Slot #1, PowerLimit 10.000W; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
			Changed: MRL- PresDet- LinkState+
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
		Address: 00000000  Data: 0000
	Capabilities: [90] Subsystem: Dell Device 0598
	Capabilities: [a0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: pcieport

00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) (prog-if 20 [EHCI])
	Subsystem: Dell Device 0598
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 23
	Region 0: Memory at c1618000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Debug port: BAR=1 offset=00a0
	Capabilities: [98] PCI Advanced Features
		AFCap: TP+ FLR+
		AFCtrl: FLR-
		AFStatus: TP-
	Kernel driver in use: ehci-pci

00:1f.0 ISA bridge: Intel Corporation HM76 Express Chipset LPC Controller (rev 04)
	Subsystem: Dell Device 0598
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: [e0] Vendor Specific Information: Len=0c <?>
	Kernel driver in use: lpc_ich

00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04) (prog-if 01 [AHCI 1.0])
	Subsystem: Dell Device 0598
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 46
	Region 0: I/O ports at 4088 [size=8]
	Region 1: I/O ports at 4094 [size=4]
	Region 2: I/O ports at 4080 [size=8]
	Region 3: I/O ports at 4090 [size=4]
	Region 4: I/O ports at 4060 [size=32]
	Region 5: Memory at c1617000 (32-bit, non-prefetchable) [size=2K]
	Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee00378  Data: 0000
	Capabilities: [70] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
	Capabilities: [b0] PCI Advanced Features
		AFCap: TP+ FLR+
		AFCtrl: FLR-
		AFStatus: TP-
	Kernel driver in use: ahci

00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04)
	Subsystem: Dell Device 0598
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin C routed to IRQ 19
	Region 0: Memory at c1615000 (64-bit, non-prefetchable) [size=256]
	Region 4: I/O ports at 4040 [size=32]

01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Thames XT/GL [Radeon HD 7600M Series] (rev ff) (prog-if ff)
	!!! Unknown header type 7f
	Kernel driver in use: radeon

07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)
	Subsystem: Dell Device 0598
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 48
	Region 0: I/O ports at 2000 [size=256]
	Region 2: Memory at c1404000 (64-bit, prefetchable) [size=4K]
	Region 4: Memory at c1400000 (64-bit, prefetchable) [size=16K]
	Capabilities: [40] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
		Address: 00000000fee003b8  Data: 0000
	Capabilities: [70] Express (v2) Endpoint, MSI 01
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 <64us
			ClockPM+ Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
		LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
		Vector table: BAR=4 offset=00000000
		PBA: BAR=4 offset=00000800
	Capabilities: [d0] Vital Product Data
		Unknown small resource type 00, will not decode more.
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
	Capabilities: [140 v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
			Status:	NegoPending- InProgress-
	Capabilities: [160 v1] Device Serial Number 14-03-00-00-36-4c-e0-00
	Kernel driver in use: r8169

08:00.0 Network controller: Intel Corporation Centrino Wireless-N 2230 (rev c4)
	Subsystem: Intel Corporation Centrino Wireless-N 2230 BGN
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 49
	Region 0: Memory at c1500000 (64-bit, non-prefetchable) [size=8K]
	Capabilities: [c8] Power Management version 3
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
		Address: 00000000fee003d8  Data: 0000
	Capabilities: [e0] Express (v1) Endpoint, MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 unlimited
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 <32us
			ClockPM+ Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
	Capabilities: [140 v1] Device Serial Number 60-36-dd-ff-ff-3c-c6-11
	Kernel driver in use: iwlwifi

dmesg

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.8.4-1-ARCH (tobias@T-POWA-LX) (gcc version 4.7.2 (GCC) ) #1 SMP PREEMPT Wed Mar 20 22:10:25 CET 2013
[    0.000000] Command line: root=/dev/mapper/vgroup-root cryptdevice=/dev/sda3:vgroup acpi_osi="!Windows 2012" ro initrd=../initramfs-linux.img BOOT_IMAGE=../vmlinuz-linux 
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d3ff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009d400-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000020200000-0x0000000040003fff] usable
[    0.000000] BIOS-e820: [mem 0x0000000040004000-0x0000000040004fff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000040005000-0x000000008ffaffff] usable
[    0.000000] BIOS-e820: [mem 0x000000008ffb0000-0x00000000913affff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000913b0000-0x000000009a3befff] usable
[    0.000000] BIOS-e820: [mem 0x000000009a3bf000-0x000000009aebefff] reserved
[    0.000000] BIOS-e820: [mem 0x000000009aebf000-0x000000009afbefff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x000000009afbf000-0x000000009affefff] ACPI data
[    0.000000] BIOS-e820: [mem 0x000000009afff000-0x000000009affffff] usable
[    0.000000] BIOS-e820: [mem 0x000000009b000000-0x000000009f9fffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000feb00000-0x00000000feb03fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed10000-0x00000000fed19fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ffb80000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000015f5fffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.7 present.
[    0.000000] DMI: Dell Inc. Inspiron 5521/0ND8WK, BIOS A03 10/24/2012
[    0.000000] e820: update [mem 0x00000000-0x0000ffff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] No AGP bridge found
[    0.000000] e820: last_pfn = 0x15f600 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-E7FFF write-protect
[    0.000000]   E8000-EFFFF write-combining
[    0.000000]   F0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 080000000 mask FE0000000 write-back
[    0.000000]   2 base 09B000000 mask FFF000000 uncachable
[    0.000000]   3 base 09C000000 mask FFC000000 uncachable
[    0.000000]   4 base 0FFA00000 mask FFFE00000 write-protect
[    0.000000]   5 base 0FFC00000 mask FFFC00000 write-protect
[    0.000000]   6 base 100000000 mask F80000000 write-back
[    0.000000]   7 base 15F600000 mask FFFE00000 uncachable
[    0.000000]   8 base 15F800000 mask FFF800000 uncachable
[    0.000000]   9 base 160000000 mask FE0000000 uncachable
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820: last_pfn = 0x9b000 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [mem 0x000fe1b0-0x000fe1bf] mapped at [ffff8800000fe1b0]
[    0.000000] initial memory mapped: [mem 0x00000000-0x1fffffff]
[    0.000000] Base memory trampoline at [ffff880000097000] 97000 size 24576
[    0.000000] init_memory_mapping: [mem 0x00000000-0x9affffff]
[    0.000000]  [mem 0x00000000-0x9affffff] page 2M
[    0.000000] kernel direct mapping tables up to 0x9affffff @ [mem 0x1fa23000-0x1fa26fff]
[    0.000000] init_memory_mapping: [mem 0x100000000-0x15f5fffff]
[    0.000000]  [mem 0x100000000-0x15f5fffff] page 2M
[    0.000000] kernel direct mapping tables up to 0x15f5fffff @ [mem 0x9a3bc000-0x9a3befff]
[    0.000000] RAMDISK: [mem 0x1fa27000-0x1fffefff]
[    0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 DELL  )
[    0.000000] ACPI: XSDT 000000009affe210 000B4 (v01 DELL    CL09    00000001      01000013)
[    0.000000] ACPI: FACP 000000009affa000 0010C (v05 DELL    CL09    00000001 ASL  00040000)
[    0.000000] ACPI: DSDT 000000009afed000 092DA (v01 DELL    CL09    00000000 ASL  00040000)
[    0.000000] ACPI: FACS 000000009afb9000 00040
[    0.000000] ACPI: SLIC 000000009affd000 00176 (v01 DELL    CL09    00000001 ASL  00040000)
[    0.000000] ACPI: UEFI 000000009affc000 00236 (v01 DELL    CL09    00000001 ASL  00040000)
[    0.000000] ACPI: ASF! 000000009affb000 000A5 (v32 DELL    CL09    00000001 ASL  00040000)
[    0.000000] ACPI: HPET 000000009aff9000 00038 (v01 DELL    CL09    00000001 ASL  00040000)
[    0.000000] ACPI: APIC 000000009aff8000 0008C (v03 DELL    CL09    00000001 ASL  00040000)
[    0.000000] ACPI: MCFG 000000009aff7000 0003C (v01 DELL    CL09    00000001 ASL  00040000)
[    0.000000] ACPI: SLIC 000000009afec000 00176 (v01 DELL    CL09    00000001 ASL  00040000)
[    0.000000] ACPI: SSDT 000000009afeb000 006FE (v01 COMPAL CRV ORB  00001000 ACPI 00040000)
[    0.000000] ACPI: BOOT 000000009afe9000 00028 (v01 DELL    CL09    00000001 ASL  00040000)
[    0.000000] ACPI: ASPT 000000009afe7000 00034 (v07 DELL    CL09    00000001 ASL  00040000)
[    0.000000] ACPI: DBGP 000000009afe6000 00034 (v01 DELL    CL09    00000001 ASL  00040000)
[    0.000000] ACPI: FPDT 000000009afe4000 00044 (v01 DELL    CL09    00000001 ASL  00040000)
[    0.000000] ACPI: MSDM 000000009afe3000 00055 (v03 DELL    CL09    00000001 ASL  00040000)
[    0.000000] ACPI: SSDT 000000009afe2000 008A2 (v01 COMPAL CRV ORB  00003000 ACPI 00040000)
[    0.000000] ACPI: SSDT 000000009afe1000 00A92 (v01 COMPAL CRV ORB  00003000 ACPI 00040000)
[    0.000000] ACPI: DMAR 000000009afe0000 000B8 (v01 DELL    CL09    00000001 ASL  00040000)
[    0.000000] ACPI: SSDT 000000009afde000 01EED (v01 COMPAL CRV ORB  00001000 ACPI 00040000)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x000000015f5fffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x15f5fffff]
[    0.000000]   NODE_DATA [mem 0x15f5fb000-0x15f5fffff]
[    0.000000]  [ffffea0000000000-ffffea00057fffff] PMD -> [ffff88015ac00000-ffff88015ebfffff] on node 0
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00010000-0x00ffffff]
[    0.000000]   DMA32    [mem 0x01000000-0xffffffff]
[    0.000000]   Normal   [mem 0x100000000-0x15f5fffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00010000-0x0009cfff]
[    0.000000]   node   0: [mem 0x00100000-0x1fffffff]
[    0.000000]   node   0: [mem 0x20200000-0x40003fff]
[    0.000000]   node   0: [mem 0x40005000-0x8ffaffff]
[    0.000000]   node   0: [mem 0x913b0000-0x9a3befff]
[    0.000000]   node   0: [mem 0x9afff000-0x9affffff]
[    0.000000]   node   0: [mem 0x100000000-0x15f5fffff]
[    0.000000] On node 0 totalpages: 1016652
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 6 pages reserved
[    0.000000]   DMA zone: 3911 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 9719 pages used for memmap
[    0.000000]   DMA32 zone: 612296 pages, LIFO batch:31
[    0.000000]   Normal zone: 6104 pages used for memmap
[    0.000000]   Normal zone: 384552 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
[    0.000000] ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] smpboot: Allowing 8 CPUs, 4 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009d000 - 000000000009e000
[    0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[    0.000000] PM: Registered nosave memory: 0000000020000000 - 0000000020200000
[    0.000000] PM: Registered nosave memory: 0000000040004000 - 0000000040005000
[    0.000000] PM: Registered nosave memory: 000000008ffb0000 - 00000000913b0000
[    0.000000] PM: Registered nosave memory: 000000009a3bf000 - 000000009aebf000
[    0.000000] PM: Registered nosave memory: 000000009aebf000 - 000000009afbf000
[    0.000000] PM: Registered nosave memory: 000000009afbf000 - 000000009afff000
[    0.000000] PM: Registered nosave memory: 000000009b000000 - 000000009fa00000
[    0.000000] PM: Registered nosave memory: 000000009fa00000 - 00000000e0000000
[    0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
[    0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000feb00000
[    0.000000] PM: Registered nosave memory: 00000000feb00000 - 00000000feb04000
[    0.000000] PM: Registered nosave memory: 00000000feb04000 - 00000000fec00000
[    0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
[    0.000000] PM: Registered nosave memory: 00000000fec01000 - 00000000fed10000
[    0.000000] PM: Registered nosave memory: 00000000fed10000 - 00000000fed1a000
[    0.000000] PM: Registered nosave memory: 00000000fed1a000 - 00000000fed1c000
[    0.000000] PM: Registered nosave memory: 00000000fed1c000 - 00000000fed20000
[    0.000000] PM: Registered nosave memory: 00000000fed20000 - 00000000fee00000
[    0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[    0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ffb80000
[    0.000000] PM: Registered nosave memory: 00000000ffb80000 - 0000000100000000
[    0.000000] e820: [mem 0x9fa00000-0xdfffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:8 nr_node_ids:1
[    0.000000] PERCPU: Embedded 28 pages/cpu @ffff88015f200000 s85056 r8192 d21440 u262144
[    0.000000] pcpu-alloc: s85056 r8192 d21440 u262144 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7 
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 1000759
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: root=/dev/mapper/vgroup-root cryptdevice=/dev/sda3:vgroup acpi_osi="!Windows 2012" ro initrd=../initramfs-linux.img BOOT_IMAGE=../vmlinuz-linux 
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] __ex_table already sorted, skipping sort
[    0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 3916672k/5756928k available (4985k kernel code, 1690320k absent, 149936k reserved, 3946k data, 820k init)
[    0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] 	Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=8.
[    0.000000] NR_IRQS:4352 nr_irqs:744 16
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] allocated 16777216 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.003333] tsc: Detected 1696.265 MHz processor
[    0.000003] Calibrating delay loop (skipped), value calculated using timer frequency.. 3393.88 BogoMIPS (lpj=5654216)
[    0.000006] pid_max: default: 32768 minimum: 301
[    0.000045] Security Framework initialized
[    0.000054] AppArmor: AppArmor disabled by boot time parameter
[    0.000402] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.001921] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.002611] Mount-cache hash table entries: 256
[    0.002832] Initializing cgroup subsys cpuacct
[    0.002835] Initializing cgroup subsys memory
[    0.002844] Initializing cgroup subsys devices
[    0.002846] Initializing cgroup subsys freezer
[    0.002848] Initializing cgroup subsys net_cls
[    0.002850] Initializing cgroup subsys blkio
[    0.002882] CPU: Physical Processor ID: 0
[    0.002883] CPU: Processor Core ID: 0
[    0.002889] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[    0.003447] mce: CPU supports 7 MCE banks
[    0.003462] CPU0: Thermal monitoring enabled (TM1)
[    0.003472] process: using mwait in idle threads
[    0.003476] Last level iTLB entries: 4KB 512, 2MB 0, 4MB 0
Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32
tlb_flushall_shift: 1
[    0.003710] Freeing SMP alternatives: 20k freed
[    0.005053] ACPI: Core revision 20121018
[    0.026098] ftrace: allocating 19369 entries in 76 pages
[    0.038844] dmar: Host address width 36
[    0.038847] dmar: DRHD base: 0x000000fed90000 flags: 0x0
[    0.038858] dmar: IOMMU 0: reg_base_addr fed90000 ver 1:0 cap c0000020e60262 ecap f0101a
[    0.038860] dmar: DRHD base: 0x000000fed91000 flags: 0x1
[    0.038866] dmar: IOMMU 1: reg_base_addr fed91000 ver 1:0 cap c9008020660262 ecap f0105a
[    0.038867] dmar: RMRR base: 0x0000009ae8c000 end: 0x0000009aeabfff
[    0.038869] dmar: RMRR base: 0x0000009b800000 end: 0x0000009f9fffff
[    0.038942] IOAPIC id 0 under DRHD base  0xfed91000 IOMMU 1
[    0.038943] HPET id 0 under DRHD base 0xfed91000
[    0.039154] Enabled IRQ remapping in x2apic mode
[    0.039156] Enabling x2apic
[    0.039157] Enabled x2apic
[    0.039163] Switched APIC routing to cluster x2apic.
[    0.039592] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.072561] smpboot: CPU0: Intel(R) Core(TM) i5-3317U CPU @ 1.70GHz (fam: 06, model: 3a, stepping: 09)
[    0.072570] TSC deadline timer enabled
[    0.072574] Performance Events: PEBS fmt1+, 16-deep LBR, IvyBridge events, Intel PMU driver.
[    0.072582] ... version:                3
[    0.072583] ... bit width:              48
[    0.072585] ... generic registers:      4
[    0.072586] ... value mask:             0000ffffffffffff
[    0.072588] ... max period:             000000007fffffff
[    0.072589] ... fixed-purpose events:   3
[    0.072590] ... event mask:             000000070000000f
[    0.109871] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.095985] smpboot: Booting Node   0, Processors  #1 #2 #3
[    0.150679] Brought up 4 CPUs
[    0.150684] smpboot: Total of 4 processors activated (13575.54 BogoMIPS)
[    0.155168] devtmpfs: initialized
[    0.156438] PM: Registering ACPI NVS region [mem 0x9aebf000-0x9afbefff] (1048576 bytes)
[    0.157369] RTC time: 16:56:36, date: 03/24/13
[    0.157420] NET: Registered protocol family 16
[    0.157593] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.157596] ACPI: bus type pci registered
[    0.157686] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.157689] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[    0.197513] PCI: Using configuration type 1 for base access
[    0.197523] dmi type 0xB1 record - unknown flag
[    0.198228] bio: create slab <bio-0> at 0
[    0.198294] ACPI: Added _OSI(Module Device)
[    0.198296] ACPI: Added _OSI(Processor Device)
[    0.198298] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.198300] ACPI: Added _OSI(Processor Aggregator Device)
[    0.198302] ACPI: Deleted _OSI(Windows 2012)
[    0.200176] ACPI: EC: Look up EC in DSDT
[    0.202200] ACPI: Executed 1 blocks of module-level executable AML code
[    0.206462] ACPI: SSDT 000000009ae17018 0083B (v01  PmRef  Cpu0Cst 00003001 INTL 20111123)
[    0.206948] ACPI: Dynamic OEM Table Load:
[    0.206951] ACPI: SSDT           (null) 0083B (v01  PmRef  Cpu0Cst 00003001 INTL 20111123)
[    0.207307] ACPI: SSDT 000000009ae18a98 00303 (v01  PmRef    ApIst 00003000 INTL 20111123)
[    0.207831] ACPI: Dynamic OEM Table Load:
[    0.207834] ACPI: SSDT           (null) 00303 (v01  PmRef    ApIst 00003000 INTL 20111123)
[    0.207995] ACPI: SSDT 000000009ae16d98 00119 (v01  PmRef    ApCst 00003000 INTL 20111123)
[    0.208482] ACPI: Dynamic OEM Table Load:
[    0.208484] ACPI: SSDT           (null) 00119 (v01  PmRef    ApCst 00003000 INTL 20111123)
[    0.209449] ACPI: Interpreter enabled
[    0.209454] ACPI: (supports S0 S3 S4 S5)
[    0.209480] ACPI: Using IOAPIC for interrupt routing
[    0.334295] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[    0.334459] ACPI: No dock devices found.
[    0.334464] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.334812] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe])
[    0.334815] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.335000] \_SB_.PCI0:_OSC invalid UUID
[    0.335002] _OSC request data:1 8 1f 
[    0.335055] \_SB_.PCI0:_OSC invalid UUID
[    0.335056] _OSC request data:1 1f 1f 
[    0.335061] pci_root PNP0A08:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[    0.335063] pci_root PNP0A08:00: Unable to request _OSC control (_OSC support mask: 0x08)
[    0.335721] PCI host bridge to bus 0000:00
[    0.335725] pci_bus 0000:00: root bus resource [bus 00-fe]
[    0.335728] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.335730] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff]
[    0.335733] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.335735] pci_bus 0000:00: root bus resource [mem 0x9fa00000-0xfeafffff]
[    0.335746] pci 0000:00:00.0: [8086:0154] type 00 class 0x060000
[    0.335794] pci 0000:00:01.0: [8086:0151] type 01 class 0x060400
[    0.335837] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.335867] pci 0000:00:02.0: [8086:0166] type 00 class 0x030000
[    0.335881] pci 0000:00:02.0: reg 10: [mem 0xc1000000-0xc13fffff 64bit]
[    0.335890] pci 0000:00:02.0: reg 18: [mem 0xb0000000-0xbfffffff 64bit pref]
[    0.335896] pci 0000:00:02.0: reg 20: [io  0x4000-0x403f]
[    0.335972] pci 0000:00:14.0: [8086:1e31] type 00 class 0x0c0330
[    0.336000] pci 0000:00:14.0: reg 10: [mem 0xc1600000-0xc160ffff 64bit]
[    0.336089] pci 0000:00:14.0: PME# supported from D3hot D3cold
[    0.336118] pci 0000:00:16.0: [8086:1e3a] type 00 class 0x078000
[    0.336149] pci 0000:00:16.0: reg 10: [mem 0xc1614000-0xc161400f 64bit]
[    0.336239] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[    0.336290] pci 0000:00:1a.0: [8086:1e2d] type 00 class 0x0c0320
[    0.336315] pci 0000:00:1a.0: reg 10: [mem 0xc1619000-0xc16193ff]
[    0.336422] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[    0.336456] pci 0000:00:1b.0: [8086:1e20] type 00 class 0x040300
[    0.336475] pci 0000:00:1b.0: reg 10: [mem 0xc1610000-0xc1613fff 64bit]
[    0.336564] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.336595] pci 0000:00:1c.0: [8086:1e10] type 01 class 0x060400
[    0.336689] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.336721] pci 0000:00:1c.1: [8086:1e12] type 01 class 0x060400
[    0.336819] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.336868] pci 0000:00:1d.0: [8086:1e26] type 00 class 0x0c0320
[    0.336894] pci 0000:00:1d.0: reg 10: [mem 0xc1618000-0xc16183ff]
[    0.336999] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    0.337030] pci 0000:00:1f.0: [8086:1e59] type 00 class 0x060100
[    0.337177] pci 0000:00:1f.2: [8086:1e03] type 00 class 0x010601
[    0.337199] pci 0000:00:1f.2: reg 10: [io  0x4088-0x408f]
[    0.337209] pci 0000:00:1f.2: reg 14: [io  0x4094-0x4097]
[    0.337220] pci 0000:00:1f.2: reg 18: [io  0x4080-0x4087]
[    0.337232] pci 0000:00:1f.2: reg 1c: [io  0x4090-0x4093]
[    0.337244] pci 0000:00:1f.2: reg 20: [io  0x4060-0x407f]
[    0.337255] pci 0000:00:1f.2: reg 24: [mem 0xc1617000-0xc16177ff]
[    0.337314] pci 0000:00:1f.2: PME# supported from D3hot
[    0.337337] pci 0000:00:1f.3: [8086:1e22] type 00 class 0x0c0500
[    0.337360] pci 0000:00:1f.3: reg 10: [mem 0xc1615000-0xc16150ff 64bit]
[    0.337388] pci 0000:00:1f.3: reg 20: [io  0x4040-0x405f]
[    0.337466] pci 0000:01:00.0: [1002:6840] type 00 class 0x030000
[    0.337480] pci 0000:01:00.0: reg 10: [mem 0xa0000000-0xafffffff 64bit pref]
[    0.337492] pci 0000:01:00.0: reg 18: [mem 0xc0000000-0xc001ffff 64bit]
[    0.337500] pci 0000:01:00.0: reg 20: [io  0x3000-0x30ff]
[    0.337514] pci 0000:01:00.0: reg 30: [mem 0xfffe0000-0xffffffff pref]
[    0.337548] pci 0000:01:00.0: supports D1 D2
[    0.341531] pci 0000:00:01.0: PCI bridge to [bus 01-06]
[    0.341535] pci 0000:00:01.0:   bridge window [io  0x3000-0x3fff]
[    0.341538] pci 0000:00:01.0:   bridge window [mem 0xc0000000-0xc0ffffff]
[    0.341543] pci 0000:00:01.0:   bridge window [mem 0xa0000000-0xafffffff 64bit pref]
[    0.341677] pci 0000:07:00.0: [10ec:8136] type 00 class 0x020000
[    0.341751] pci 0000:07:00.0: reg 10: [io  0x2000-0x20ff]
[    0.341878] pci 0000:07:00.0: reg 18: [mem 0xc1404000-0xc1404fff 64bit pref]
[    0.341956] pci 0000:07:00.0: reg 20: [mem 0xc1400000-0xc1403fff 64bit pref]
[    0.342305] pci 0000:07:00.0: supports D1 D2
[    0.342308] pci 0000:07:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.348241] pci 0000:00:1c.0: PCI bridge to [bus 07]
[    0.348246] pci 0000:00:1c.0:   bridge window [io  0x2000-0x2fff]
[    0.348257] pci 0000:00:1c.0:   bridge window [mem 0xc1400000-0xc14fffff 64bit pref]
[    0.348383] pci 0000:08:00.0: [8086:0887] type 00 class 0x028000
[    0.348440] pci 0000:08:00.0: reg 10: [mem 0xc1500000-0xc1501fff 64bit]
[    0.348687] pci 0000:08:00.0: PME# supported from D0 D3hot D3cold
[    0.354921] pci 0000:00:1c.1: PCI bridge to [bus 08]
[    0.354930] pci 0000:00:1c.1:   bridge window [mem 0xc1500000-0xc15fffff]
[    0.354980] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[    0.355021] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[    0.355063] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG0._PRT]
[    0.355109] ACPI _OSC control for PCIe not granted, disabling ASPM
[    0.358134] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 10 11 12 14 15) *7
[    0.358200] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[    0.358253] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.358305] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[    0.358356] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.358408] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 10 11 12 14 15) *7
[    0.358460] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[    0.358511] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[    0.358615] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    0.358621] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=none,locks=none
[    0.358623] vgaarb: loaded
[    0.358624] vgaarb: bridge control possible 0000:01:00.0
[    0.358626] vgaarb: no bridge control possible 0000:00:02.0
[    0.358663] PCI: Using ACPI for IRQ routing
[    0.366261] PCI: pci_cache_line_size set to 64 bytes
[    0.366380] e820: reserve RAM buffer [mem 0x0009d400-0x0009ffff]
[    0.366382] e820: reserve RAM buffer [mem 0x40004000-0x43ffffff]
[    0.366384] e820: reserve RAM buffer [mem 0x8ffb0000-0x8fffffff]
[    0.366386] e820: reserve RAM buffer [mem 0x9a3bf000-0x9bffffff]
[    0.366388] e820: reserve RAM buffer [mem 0x9b000000-0x9bffffff]
[    0.366390] e820: reserve RAM buffer [mem 0x15f600000-0x15fffffff]
[    0.366493] NetLabel: Initializing
[    0.366495] NetLabel:  domain hash size = 128
[    0.366496] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.366509] NetLabel:  unlabeled traffic allowed by default
[    0.366533] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[    0.366540] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[    0.368554] Switching to clocksource hpet
[    0.373873] pnp: PnP ACPI init
[    0.373891] ACPI: bus type pnp registered
[    0.373925] pnp 00:00: [dma 4]
[    0.373953] pnp 00:00: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.373980] pnp 00:01: Plug and Play ACPI device, IDs INT0800 (active)
[    0.374094] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
[    0.374137] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.374191] system 00:04: [io  0x0680-0x069f] has been reserved
[    0.374194] system 00:04: [io  0x1000-0x100f] has been reserved
[    0.374197] system 00:04: [io  0xffff] has been reserved
[    0.374199] system 00:04: [io  0xffff] has been reserved
[    0.374202] system 00:04: [io  0x0400-0x0453] has been reserved
[    0.374204] system 00:04: [io  0x0458-0x047f] has been reserved
[    0.374207] system 00:04: [io  0x0500-0x057f] has been reserved
[    0.374209] system 00:04: [io  0x164e-0x164f] has been reserved
[    0.374212] system 00:04: [io  0xfd60-0xfd63] has been reserved
[    0.374216] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.374250] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.374307] system 00:06: [io  0x0454-0x0457] has been reserved
[    0.374311] system 00:06: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[    0.374363] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.374402] pnp 00:08: Plug and Play ACPI device, IDs DLL05b9 PNP0f13 (active)
[    0.432013] system 00:09: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.432016] system 00:09: [mem 0xfed10000-0xfed17fff] has been reserved
[    0.432019] system 00:09: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.432022] system 00:09: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.432025] system 00:09: [mem 0xe0000000-0xefffffff] has been reserved
[    0.432027] system 00:09: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.432030] system 00:09: [mem 0xfed90000-0xfed93fff] could not be reserved
[    0.432033] system 00:09: [mem 0xff000000-0xff000fff] has been reserved
[    0.432036] system 00:09: [mem 0xff010000-0xffffffff] could not be reserved
[    0.432039] system 00:09: [mem 0xfee00000-0xfeefffff] could not be reserved
[    0.432041] system 00:09: [mem 0x9fa00000-0x9fa00fff] has been reserved
[    0.432045] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.432443] system 00:0a: [mem 0x20000000-0x201fffff] has been reserved
[    0.432447] system 00:0a: [mem 0x40004000-0x40004fff] has been reserved
[    0.432450] system 00:0a: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.432473] pnp: PnP ACPI: found 11 devices
[    0.432475] ACPI: ACPI bus type pnp unregistered
[    0.439555] pci 0000:01:00.0: no compatible bridge window for [mem 0xfffe0000-0xffffffff pref]
[    0.439592] pci 0000:01:00.0: BAR 6: assigned [mem 0xc0020000-0xc003ffff pref]
[    0.439596] pci 0000:00:01.0: PCI bridge to [bus 01-06]
[    0.439599] pci 0000:00:01.0:   bridge window [io  0x3000-0x3fff]
[    0.439604] pci 0000:00:01.0:   bridge window [mem 0xc0000000-0xc0ffffff]
[    0.439607] pci 0000:00:01.0:   bridge window [mem 0xa0000000-0xafffffff 64bit pref]
[    0.439612] pci 0000:00:1c.0: PCI bridge to [bus 07]
[    0.439616] pci 0000:00:1c.0:   bridge window [io  0x2000-0x2fff]
[    0.439626] pci 0000:00:1c.0:   bridge window [mem 0xc1400000-0xc14fffff 64bit pref]
[    0.439634] pci 0000:00:1c.1: PCI bridge to [bus 08]
[    0.439641] pci 0000:00:1c.1:   bridge window [mem 0xc1500000-0xc15fffff]
[    0.439684] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.439686] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.439689] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.439691] pci_bus 0000:00: resource 7 [mem 0x9fa00000-0xfeafffff]
[    0.439694] pci_bus 0000:01: resource 0 [io  0x3000-0x3fff]
[    0.439696] pci_bus 0000:01: resource 1 [mem 0xc0000000-0xc0ffffff]
[    0.439699] pci_bus 0000:01: resource 2 [mem 0xa0000000-0xafffffff 64bit pref]
[    0.439702] pci_bus 0000:07: resource 0 [io  0x2000-0x2fff]
[    0.439704] pci_bus 0000:07: resource 2 [mem 0xc1400000-0xc14fffff 64bit pref]
[    0.439707] pci_bus 0000:08: resource 1 [mem 0xc1500000-0xc15fffff]
[    0.439745] NET: Registered protocol family 2
[    0.439925] TCP established hash table entries: 32768 (order: 7, 524288 bytes)
[    0.440055] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.440144] TCP: Hash tables configured (established 32768 bind 32768)
[    0.440165] TCP: reno registered
[    0.440175] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.440195] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.440275] NET: Registered protocol family 1
[    0.440290] pci 0000:00:02.0: Boot video device
[    0.465207] PCI: CLS 64 bytes, default 64
[    0.465250] Unpacking initramfs...
[    0.617159] Freeing initrd memory: 5984k freed
[    0.618119] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.618125] software IO TLB [mem 0x963bc000-0x9a3bc000] (64MB) mapped at [ffff8800963bc000-ffff88009a3bbfff]
[    0.618159] Simple Boot Flag at 0x44 set to 0x1
[    0.618603] audit: initializing netlink socket (disabled)
[    0.618621] type=2000 audit(1364144196.609:1): initialized
[    0.635707] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.637479] VFS: Disk quotas dquot_6.5.2
[    0.637530] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.637724] msgmni has been set to 7661
[    0.637993] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.638030] io scheduler noop registered
[    0.638033] io scheduler deadline registered
[    0.638040] io scheduler cfq registered (default)
[    0.638160] pcieport 0000:00:01.0: irq 42 for MSI/MSI-X
[    0.638430] intel_idle: MWAIT substates: 0x21120
[    0.638432] intel_idle: v0.4 model 0x3A
[    0.638434] intel_idle: lapic_timer_reliable_states 0xffffffff
[    0.638475] GHES: HEST is not enabled!
[    0.638531] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.639052] Linux agpgart interface v0.103
[    0.639137] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    0.659231] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.659245] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.659387] mousedev: PS/2 mouse device common for all mice
[    0.659427] rtc_cmos 00:05: RTC can wake from S4
[    0.659587] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[    0.659618] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[    0.659720] cpuidle: using governor ladder
[    0.659852] cpuidle: using governor menu
[    0.659854] EFI Variables Facility v0.08 2004-May-17
[    0.659913] drop_monitor: Initializing network drop monitor service
[    0.660002] TCP: cubic registered
[    0.660115] NET: Registered protocol family 10
[    0.660290] NET: Registered protocol family 17
[    0.660300] Key type dns_resolver registered
[    0.660581] PM: Hibernation image not present or could not be loaded.
[    0.660591] registered taskstats version 1
[    0.661134]   Magic number: 5:373:945
[    0.661146] tty tty2: hash matches
[    0.661168] cpu cpu0: hash matches
[    0.661215] rtc_cmos 00:05: setting system clock to 2013-03-24 16:56:37 UTC (1364144197)
[    0.663239] Freeing unused kernel memory: 820k freed
[    0.663371] Write protecting the kernel read-only data: 8192k
[    0.667503] Freeing unused kernel memory: 1148k freed
[    0.669277] Freeing unused kernel memory: 440k freed
[    0.677920] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    0.678141] systemd-udevd[56]: starting version 198
[    0.684163] [drm] Initialized drm 1.1.0 20060810
[    0.685602] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:01/PNP0C0C:00/input/input1
[    0.685611] ACPI: Power Button [PWRB]
[    0.685756] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2
[    0.685803] ACPI: Lid Switch [LID0]
[    0.685931] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    0.685937] ACPI: Power Button [PWRF]
[    0.691332] [drm] Memory usable by graphics device = 2048M
[    0.691342] i915 0000:00:02.0: setting latency timer to 64
[    0.740353] i915 0000:00:02.0: irq 43 for MSI/MSI-X
[    0.740412] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[    0.740415] [drm] Driver supports precise vblank timestamp query.
[    0.740553] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=none:owns=io+mem
[    0.740557] vgaarb: transferring owner from PCI:0000:00:02.0 to PCI:0000:01:00.0
[    0.941304] [drm] GMBUS [i915 gmbus vga] timed out, falling back to bit banging on pin 2
[    0.985506] fbcon: inteldrmfb (fb0) is primary device
[    1.617168] tsc: Refined TSC clocksource calibration: 1696.147 MHz
[    1.617173] Switching to clocksource tsc
[    1.701411] Console: switching to colour frame buffer device 170x48
[    1.705696] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[    1.705699] i915 0000:00:02.0: registered panic notifier
[    1.705922] [Firmware Bug]: ACPI(PEGP) defines _DOD but not _DOS
[    1.706730] ACPI Error: [\_SB_.PCI0.GFX0.DD02._BCL] Namespace lookup failure, AE_NOT_FOUND (20121018/psargs-359)
[    1.706738] ACPI Error: Method parse/execution failed [\_SB_.PCI0.PEG0.PEGP.DD02._BCL] (Node ffff88015927a988), AE_NOT_FOUND (20121018/psparse-537)
[    1.706902] ACPI: Video Device [PEGP] (multi-head: yes  rom: no  post: no)
[    1.706976] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:2b/LNXVIDEO:00/input/input4
[    1.709495] ACPI Warning: _BQC returned an invalid level (20121018/video-486)
[    1.709657] acpi device:39: registered as cooling_device0
[    1.709850] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[    1.709931] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:01/input/input5
[    1.709963] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[    1.715692] [drm] radeon defaulting to kernel modesetting.
[    1.715695] [drm] radeon kernel modesetting enabled.
[    1.715706] VGA switcheroo: detected switching method \_SB_.PCI0.GFX0.ATPX handle
[    1.715744] radeon 0000:01:00.0: enabling device (0000 -> 0003)
[    1.715957] [drm] initializing kernel modesetting (TURKS 0x1002:0x6840 0x1028:0x0598).
[    1.716022] [drm] register mmio base: 0xC0000000
[    1.716025] [drm] register mmio size: 131072
[    1.716029] vga_switcheroo: enabled
[    1.716208] ATPX version 1
[    2.157608] ATOM BIOS: Dell/Compal
[    2.157656] radeon 0000:01:00.0: VRAM: 1024M 0x0000000000000000 - 0x000000003FFFFFFF (1024M used)
[    2.157660] radeon 0000:01:00.0: GTT: 512M 0x0000000040000000 - 0x000000005FFFFFFF
[    2.157669] mtrr: no more MTRRs available
[    2.157671] [drm] Detected VRAM RAM=1024M, BAR=256M
[    2.157673] [drm] RAM width 128bits DDR
[    2.157762] [TTM] Zone  kernel: Available graphics memory: 1962542 kiB
[    2.157764] [TTM] Initializing pool allocator
[    2.157769] [TTM] Initializing DMA pool allocator
[    2.157800] [drm] radeon: 1024M of VRAM memory ready
[    2.157802] [drm] radeon: 512M of GTT memory ready.
[    2.157826] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[    2.157828] [drm] Driver supports precise vblank timestamp query.
[    2.157876] radeon 0000:01:00.0: irq 44 for MSI/MSI-X
[    2.157888] radeon 0000:01:00.0: radeon: using MSI.
[    2.157926] [drm] radeon: irq initialized.
[    2.157932] [drm] GART: num cpu pages 131072, num gpu pages 131072
[    2.158492] [drm] probing gen 2 caps for device 8086:151 = 2/6
[    2.158497] [drm] enabling PCIE gen 2 link speeds, disable with radeon.pcie_gen2=0
[    2.158682] [drm] Loading TURKS Microcode
[    2.160953] [drm] PCIE GART of 512M enabled (table at 0x0000000000040000).
[    2.161077] radeon 0000:01:00.0: WB enabled
[    2.161081] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000040000c00 and cpu addr 0xffff8801566f8c00
[    2.161083] radeon 0000:01:00.0: fence driver on ring 3 use gpu addr 0x0000000040000c0c and cpu addr 0xffff8801566f8c0c
[    2.177666] [drm] ring test on 0 succeeded in 1 usecs
[    2.177725] [drm] ring test on 3 succeeded in 1 usecs
[    2.177985] [drm] ib test on ring 0 succeeded in 0 usecs
[    2.178034] [drm] ib test on ring 3 succeeded in 0 usecs
[    2.178272] [drm] Radeon Display Connectors
[    2.183303] [drm] Internal thermal controller without fan control
[    2.184195] [drm] radeon: power management initialized
[    2.184319] radeon 0000:01:00.0: No connectors reported connected with modes
[    2.184323] [drm] Cannot find any crtc or sizes - going 1024x768
[    2.185965] [drm] fb mappable at 0xA0142000
[    2.185967] [drm] vram apper at 0xA0000000
[    2.185968] [drm] size 3145728
[    2.185970] [drm] fb depth is 24
[    2.185971] [drm]    pitch is 4096
[    2.186052] radeon 0000:01:00.0: fb1: radeondrmfb frame buffer device
[    2.186057] [drm] Initialized radeon 2.29.0 20080528 for 0000:01:00.0 on minor 1
[    2.225511] ACPI: bus type usb registered
[    2.225543] usbcore: registered new interface driver usbfs
[    2.225557] usbcore: registered new interface driver hub
[    2.225609] usbcore: registered new device driver usb
[    2.226704] xhci_hcd 0000:00:14.0: setting latency timer to 64
[    2.226711] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    2.226730] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[    2.226802] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.226850] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[    2.226878] xhci_hcd 0000:00:14.0: irq 21, io mem 0xc1600000
[    2.226968] xhci_hcd 0000:00:14.0: irq 45 for MSI/MSI-X
[    2.227186] ehci-pci: EHCI PCI platform driver
[    2.227315] xHCI xhci_add_endpoint called for root hub
[    2.227317] xHCI xhci_check_bandwidth called for root hub
[    2.227352] hub 1-0:1.0: USB hub found
[    2.227362] hub 1-0:1.0: 4 ports detected
[    2.228056] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    2.228062] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[    2.228252] xHCI xhci_add_endpoint called for root hub
[    2.228254] xHCI xhci_check_bandwidth called for root hub
[    2.228345] hub 2-0:1.0: USB hub found
[    2.228353] hub 2-0:1.0: 4 ports detected
[    2.229508] SCSI subsystem initialized
[    2.232050] ACPI: bus type scsi registered
[    2.232830] libata version 3.00 loaded.
[    2.236465] ehci-pci 0000:00:1a.0: setting latency timer to 64
[    2.236472] ehci-pci 0000:00:1a.0: EHCI Host Controller
[    2.236484] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 3
[    2.236502] ehci-pci 0000:00:1a.0: debug port 2
[    2.240397] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[    2.240431] ehci-pci 0000:00:1a.0: irq 16, io mem 0xc1619000
[    2.249713] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[    2.249904] hub 3-0:1.0: USB hub found
[    2.249910] hub 3-0:1.0: 2 ports detected
[    2.250083] ehci-pci 0000:00:1d.0: setting latency timer to 64
[    2.250088] ehci-pci 0000:00:1d.0: EHCI Host Controller
[    2.250094] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 4
[    2.250111] ehci-pci 0000:00:1d.0: debug port 2
[    2.254021] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[    2.254046] ehci-pci 0000:00:1d.0: irq 23, io mem 0xc1618000
[    2.262987] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[    2.263153] hub 4-0:1.0: USB hub found
[    2.263157] hub 4-0:1.0: 2 ports detected
[    2.263288] ahci 0000:00:1f.2: version 3.0
[    2.263398] ahci 0000:00:1f.2: irq 46 for MSI/MSI-X
[    2.276394] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x5 impl SATA mode
[    2.276400] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ems apst 
[    2.276408] ahci 0000:00:1f.2: setting latency timer to 64
[    2.283951] scsi0 : ahci
[    2.284050] scsi1 : ahci
[    2.284130] scsi2 : ahci
[    2.284206] scsi3 : ahci
[    2.284279] scsi4 : ahci
[    2.284354] scsi5 : ahci
[    2.284406] ata1: SATA max UDMA/133 abar m2048@0xc1617000 port 0xc1617100 irq 46
[    2.284408] ata2: DUMMY
[    2.284412] ata3: SATA max UDMA/133 abar m2048@0xc1617000 port 0xc1617200 irq 46
[    2.284413] ata4: DUMMY
[    2.284415] ata5: DUMMY
[    2.284416] ata6: DUMMY
[    2.356670] [drm] Enabling RC6 states: RC6 on, RC6p on, RC6pp off
[    2.586009] usb 1-4: new full-speed USB device number 2 using xhci_hcd
[    2.602617] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    2.602661] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    2.604138] ata3.00: ATAPI: MATSHITA DVD+/-RW UJ8C2, 1.01, max UDMA/133
[    2.605436] ata3.00: configured for UDMA/133
[    2.608735] usbcore: registered new interface driver usbhid
[    2.608738] usbhid: USB HID core driver
[    2.610150] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-4/input2
[    2.632994] ata1.00: ATA-8: ST500LT012-9WS142, 0001SDM1, max UDMA/133
[    2.632999] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[    2.673604] ata1.00: configured for UDMA/133
[    2.673875] scsi 0:0:0:0: Direct-Access     ATA      ST500LT012-9WS14 0001 PQ: 0 ANSI: 5
[    2.675801] scsi 2:0:0:0: CD-ROM            MATSHITA DVD+-RW UJ8C2    1.01 PQ: 0 ANSI: 5
[    2.679650] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[    2.679655] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    2.679740] sd 0:0:0:0: [sda] Write Protect is off
[    2.679744] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.679778] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.683129] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.683133] cdrom: Uniform CD-ROM driver Revision: 3.20
[    2.683406] sr 2:0:0:0: Attached scsi CD-ROM sr0
[    2.689770]  sda: sda1 sda2 sda3
[    2.690338] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.709151] usb 3-1: new high-speed USB device number 2 using ehci-pci
[    2.833401] hub 3-1:1.0: USB hub found
[    2.833549] hub 3-1:1.0: 6 ports detected
[    2.938875] usb 4-1: new high-speed USB device number 2 using ehci-pci
[    3.023095] device-mapper: uevent: version 1.0.3
[    3.023439] device-mapper: ioctl: 4.23.1-ioctl (2012-12-18) initialised: dm-devel@redhat.com
[    3.062735] hub 4-1:1.0: USB hub found
[    3.062893] hub 4-1:1.0: 6 ports detected
[    3.142219] usb 3-1.1: new full-speed USB device number 3 using ehci-pci
[    3.308645] usb 3-1.3: new high-speed USB device number 4 using ehci-pci
[    3.458472] usb 3-1.4: new high-speed USB device number 5 using ehci-pci
[   10.171784] bio: create slab <bio-1> at 1
[   10.441449] bio: create slab <bio-1> at 1
[   11.383997] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)
[   12.026831] systemd[1]: Smack is not enabled in the kernel, not loading access rules.
[   12.134665] systemd[1]: systemd 198 running in system mode. (+PAM -LIBWRAP -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
[   12.186036] systemd[1]: Set hostname to <dell-arch>.
[   12.682833] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[   12.682907] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[   12.682923] systemd[1]: Starting Remote File Systems.
[   12.683151] systemd[1]: Reached target Remote File Systems.
[   12.683165] systemd[1]: Starting Device-mapper event daemon FIFOs.
[   12.683300] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[   12.683312] systemd[1]: Starting LVM2 metadata daemon socket.
[   12.683437] systemd[1]: Listening on LVM2 metadata daemon socket.
[   12.683449] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[   12.683570] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[   12.683582] systemd[1]: Starting Delayed Shutdown Socket.
[   12.683698] systemd[1]: Listening on Delayed Shutdown Socket.
[   12.683717] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[   12.683762] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[   12.683860] systemd[1]: Starting udev Kernel Socket.
[   12.683982] systemd[1]: Listening on udev Kernel Socket.
[   12.684051] systemd[1]: Starting udev Control Socket.
[   12.684173] systemd[1]: Listening on udev Control Socket.
[   12.684186] systemd[1]: Starting Encrypted Volumes.
[   12.684284] systemd[1]: Reached target Encrypted Volumes.
[   12.684320] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[   12.685501] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[   12.685517] systemd[1]: Starting Journal Socket.
[   12.686632] systemd[1]: Listening on Journal Socket.
[   12.738202] systemd[1]: Started Load Kernel Modules.
[   12.738243] systemd[1]: Mounted FUSE Control File System.
[   12.738261] systemd[1]: Starting Setup Virtual Console...
[   12.747658] systemd[1]: Mounting Huge Pages File System...
[   12.778612] systemd[1]: Starting Apply Kernel Variables...
[   12.787198] systemd[1]: Mounting POSIX Message Queue File System...
[   12.801660] systemd[1]: Starting udev Kernel Device Manager...
[   12.807287] systemd[1]: Starting udev Coldplug all Devices...
[   12.810654] systemd[1]: Starting Journal Service...
[   12.818263] systemd[1]: Started Journal Service.
[   12.863302] systemd[1]: Started Set Up Additional Binary Formats.
[   12.863331] systemd[1]: Mounting Configuration File System...
[   12.881188] systemd[1]: Expecting device dev-mapper-vgroup\x2dswap.device...
[   12.882372] systemd[1]: Mounting Temporary Directory...
[   12.925214] systemd[1]: Started File System Check on Root Device.
[   12.925234] systemd[1]: Starting Remount Root and Kernel File Systems...
[   12.930463] systemd[1]: Expecting device dev-mapper-vgroup\x2dhome.device...
[   12.931620] systemd[1]: Expecting device dev-sda2.device...
[   13.102058] systemd-udevd[213]: starting version 198
[   13.305929] EXT4-fs (dm-1): re-mounted. Opts: data=ordered
[   14.124394] microcode: CPU0 sig=0x306a9, pf=0x10, revision=0x15
[   14.133368] microcode: CPU1 sig=0x306a9, pf=0x10, revision=0x15
[   14.134049] microcode: CPU2 sig=0x306a9, pf=0x10, revision=0x15
[   14.134713] microcode: CPU3 sig=0x306a9, pf=0x10, revision=0x15
[   14.135472] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[   14.480958] input: PC Speaker as /devices/platform/pcspkr/input/input6
[   14.528002] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[   14.551623] wmi: Mapper loaded
[   14.553538] ACPI: Requesting acpi_cpufreq
[   14.571664] ACPI: Battery Slot [BAT1] (battery present)
[   14.572153] ACPI: AC Adapter [ACAD] (on-line)
[   14.704544] input: Dell WMI hotkeys as /devices/virtual/input/input7
[   15.031473] ACPI Warning: 0x0000000000004040-0x000000000000405f SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20121018/utaddress-251)
[   15.031482] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   15.043031] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \PMIO 1 (20121018/utaddress-251)
[   15.043041] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   15.043047] ACPI Warning: 0x0000000000000530-0x000000000000053f SystemIO conflicts with Region \_SB_.PCI0.PEG0.PEGP.GPIO 1 (20121018/utaddress-251)
[   15.043053] ACPI Warning: 0x0000000000000530-0x000000000000053f SystemIO conflicts with Region \GPIO 2 (20121018/utaddress-251)
[   15.043058] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   15.043061] ACPI Warning: 0x0000000000000500-0x000000000000052f SystemIO conflicts with Region \_SB_.PCI0.PEG0.PEGP.GPIO 1 (20121018/utaddress-251)
[   15.043066] ACPI Warning: 0x0000000000000500-0x000000000000052f SystemIO conflicts with Region \GPIO 2 (20121018/utaddress-251)
[   15.043070] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   15.043072] lpc_ich: Resource conflict(s) found affecting gpio_ich
[   15.073699] iTCO_vendor_support: vendor-support=0
[   15.082724] mei 0000:00:16.0: setting latency timer to 64
[   15.082858] mei 0000:00:16.0: irq 47 for MSI/MSI-X
[   15.086613] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[   15.086864] r8169 0000:07:00.0: irq 48 for MSI/MSI-X
[   15.087073] r8169 0000:07:00.0 eth0: RTL8105e at 0xffffc900107b4000, e0:db:55:de:0a:8d, XID 00c00000 IRQ 48
[   15.091939] systemd-udevd[242]: renamed network interface eth0 to enp7s0
[   15.373620] psmouse serio1: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1, caps: 0xd00123/0x840300/0x26c00, board id: 2382, fw id: 1238635
[   15.405995] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[   15.406076] iTCO_wdt: Found a Panther Point TCO device (Version=2, TCOBASE=0x0460)
[   15.406625] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   15.426306] cfg80211: Calling CRDA to update world regulatory domain
[   15.444168] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8
[   15.455083] Intel(R) Wireless WiFi driver for Linux, in-tree:
[   15.455087] Copyright(c) 2003-2012 Intel Corporation
[   15.455364] iwlwifi 0000:08:00.0: irq 49 for MSI/MSI-X
[   15.537497] snd_hda_intel 0000:00:1b.0: irq 50 for MSI/MSI-X
[   15.770650] iwlwifi 0000:08:00.0: loaded firmware version 18.168.6.1
[   15.831500] iwlwifi 0000:08:00.0: CONFIG_IWLWIFI_DEBUG disabled
[   15.831503] iwlwifi 0000:08:00.0: CONFIG_IWLWIFI_DEBUGFS disabled
[   15.831505] iwlwifi 0000:08:00.0: CONFIG_IWLWIFI_DEVICE_TRACING enabled
[   15.831506] iwlwifi 0000:08:00.0: CONFIG_IWLWIFI_DEVICE_TESTMODE disabled
[   15.831508] iwlwifi 0000:08:00.0: CONFIG_IWLWIFI_P2P disabled
[   15.831510] iwlwifi 0000:08:00.0: Detected Intel(R) Centrino(R) Wireless-N 2230 BGN, REV=0xC8
[   15.831581] iwlwifi 0000:08:00.0: L1 Enabled; Disabling L0S
[   15.899891] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs'
[   15.909022] hda_codec: ALC282: SKU not ready 0x598301f0
[   15.910458] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input9
[   15.933451] systemd-udevd[246]: renamed network interface wlan0 to wlp8s0
[   15.979326] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[   15.979420] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[   15.979478] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[   16.044977] Adding 4194300k swap on /dev/mapper/vgroup-swap.  Priority:-1 extents:1 across:4194300k 
[   16.308175] rts5139: module is from the staging directory, the quality is unknown, you have been warned.
[   16.311869] scsi6 : SCSI emulation for RTS5139 USB card reader
[   16.312036] scsi 6:0:0:0: Direct-Access     Generic- xD/SD/M.S.       1.00 PQ: 0 ANSI: 0 CCS
[   16.315326] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[   16.318180] usbcore: registered new interface driver rts5139
[   16.320395] media: Linux media interface: v0.10
[   16.327096] Linux video capture interface: v2.00
[   16.449686] Bluetooth: Core ver 2.16
[   16.449701] NET: Registered protocol family 31
[   16.449702] Bluetooth: HCI device and connection manager initialized
[   16.449708] Bluetooth: HCI socket layer initialized
[   16.449710] Bluetooth: L2CAP socket layer initialized
[   16.449714] Bluetooth: SCO socket layer initialized
[   16.495370] usbcore: registered new interface driver btusb
[   16.535106] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_HD (0c45:64ad)
[   16.576147] input: Laptop_Integrated_Webcam_HD as /devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.4/3-1.4:1.0/input/input13
[   16.576348] usbcore: registered new interface driver uvcvideo
[   16.576352] USB Video Class driver (1.1.1)
[   17.480659] EXT4-fs (sda2): mounting ext3 file system using the ext4 subsystem
[   17.481390] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: stripe=4,data=ordered
[   17.893045] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: data=ordered
[   17.986473] systemd-journald[215]: Received SIGUSR1
[   18.131121] systemd-journald[215]: File /var/log/journal/1833fdb3983043cd8eef09c66d411f81/system.journal corrupted or uncleanly shut down, renaming and replacing.
[   18.684375] radeon: switched off
[   21.815972] r8169 0000:07:00.0 enp7s0: link down
[   21.816001] IPv6: ADDRCONF(NETDEV_UP): enp7s0: link is not ready
[   21.817470] iwlwifi 0000:08:00.0: L1 Enabled; Disabling L0S
[   21.824949] iwlwifi 0000:08:00.0: Radio type=0x2-0x0-0x0
[   22.196595] iwlwifi 0000:08:00.0: L1 Enabled; Disabling L0S
[   22.204150] iwlwifi 0000:08:00.0: Radio type=0x2-0x0-0x0
[   22.412832] IPv6: ADDRCONF(NETDEV_UP): wlp8s0: link is not ready
[   22.817990] EXT4-fs (dm-1): re-mounted. Opts: data=ordered,commit=0
[   22.825693] EXT4-fs (sda2): re-mounted. Opts: stripe=4,data=ordered,commit=0
[   22.829028] EXT4-fs (dm-3): re-mounted. Opts: data=ordered,commit=0
[   23.911060] wlp8s0: authenticate with 00:14:6c:0f:05:aa
[   23.917612] wlp8s0: capabilities/regulatory prevented using AP HT/VHT configuration, downgraded
[   23.920365] wlp8s0: send auth to 00:14:6c:0f:05:aa (try 1/3)
[   23.923413] wlp8s0: authenticated
[   23.923718] iwlwifi 0000:08:00.0 wlp8s0: disabling HT as WMM/QoS is not supported by the AP
[   23.923732] iwlwifi 0000:08:00.0 wlp8s0: disabling VHT as WMM/QoS is not supported by the AP
[   23.927095] wlp8s0: associate with 00:14:6c:0f:05:aa (try 1/3)
[   23.929465] wlp8s0: RX AssocResp from 00:14:6c:0f:05:aa (capab=0x411 status=0 aid=3)
[   23.935582] wlp8s0: associated
[   23.935654] IPv6: ADDRCONF(NETDEV_CHANGE): wlp8s0: link becomes ready
[   63.734811] input: Logitech Unifying Device. Wireless PID:1017 as /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.2/0003:046D:C52B.0003/input/input14
[   63.736210] logitech-djdevice 0003:046D:C52B.0004: input,hidraw1: USB HID v1.11 Mouse [Logitech Unifying Device. Wireless PID:1017] on usb-0000:00:14.0-4:1
[ 1277.094881] radeon: switched on
[ 1277.112499] [drm] probing gen 2 caps for device 8086:151 = 2/6
[ 1277.112503] [drm] enabling PCIE gen 2 link speeds, disable with radeon.pcie_gen2=0
[ 1277.116933] [drm] PCIE GART of 512M enabled (table at 0x0000000000040000).
[ 1277.117101] radeon 0000:01:00.0: WB enabled
[ 1277.117107] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000040000c00 and cpu addr 0xffff8801566f8c00
[ 1277.117111] radeon 0000:01:00.0: fence driver on ring 3 use gpu addr 0x0000000040000c0c and cpu addr 0xffff8801566f8c0c
[ 1277.133737] [drm] ring test on 0 succeeded in 1 usecs
[ 1277.133794] [drm] ring test on 3 succeeded in 1 usecs
[ 1277.133839] [drm] ib test on ring 0 succeeded in 0 usecs
[ 1277.133887] [drm] ib test on ring 3 succeeded in 1 usecs
[ 1277.266752] fbcon: Remapping primary device, fb1, to tty 1-63
[ 1277.266830] i915: switched off
[ 1281.563558] i915: switched on
[ 1281.575969] i915 0000:00:02.0: setting latency timer to 64
[ 1281.945375] fbcon: Remapping primary device, fb0, to tty 1-63
[ 1281.945471] radeon: switched off
[ 1282.824428] [drm] Enabling RC6 states: RC6 on, RC6p on, RC6pp off
[ 1295.306423] radeon: switched on
[ 1295.324104] [drm] probing gen 2 caps for device 8086:151 = 2/6
[ 1295.324108] [drm] enabling PCIE gen 2 link speeds, disable with radeon.pcie_gen2=0
[ 1295.327087] [drm] PCIE GART of 512M enabled (table at 0x0000000000040000).
[ 1295.327181] radeon 0000:01:00.0: WB enabled
[ 1295.327183] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000040000c00 and cpu addr 0xffff8801566f8c00
[ 1295.327184] radeon 0000:01:00.0: fence driver on ring 3 use gpu addr 0x0000000040000c0c and cpu addr 0xffff8801566f8c0c
[ 1295.343410] [drm] ring test on 0 succeeded in 1 usecs
[ 1295.343468] [drm] ring test on 3 succeeded in 1 usecs
[ 1295.343513] [drm] ib test on ring 0 succeeded in 0 usecs
[ 1295.343562] [drm] ib test on ring 3 succeeded in 1 usecs
[ 1297.826449] fbcon: Remapping primary device, fb1, to tty 1-63
[ 1297.826529] i915: switched off
[ 1308.460016] i915: switched on
[ 1308.470440] i915 0000:00:02.0: setting latency timer to 64
[ 1308.843841] fbcon: Remapping primary device, fb0, to tty 1-63
[ 1308.843910] radeon: switched off
[ 1309.792166] [drm] Enabling RC6 states: RC6 on, RC6p on, RC6pp off

Offline

#2 2013-03-25 20:29:32

outro_tipo
Member
Registered: 2013-03-08
Posts: 28

Re: Hybrid graphics i915/radeon. Switch to radeon results to black screen

i always had problems with switchable graphics and now i dont use them anymore, maybe:
echo DIGD > /sys/kernel/debug/vgaswitcheroo/switch
echo DDIS > /sys/kernel/debug/vgaswitcheroo/switch

Offline

#3 2013-03-26 19:25:34

damdim
Member
Registered: 2010-03-13
Posts: 48

Re: Hybrid graphics i915/radeon. Switch to radeon results to black screen

As I understand, these are only useful when X is running, which is not my case. Either way, they have the same effect as IGD/DIS.

Offline

#4 2013-03-29 15:23:09

aximab
Member
Registered: 2013-03-29
Posts: 1

Re: Hybrid graphics i915/radeon. Switch to radeon results to black screen

Hi there,
First I am not using archlinux but debian.
However I have the exact same issue with a compiled "by hand" kernel 3.7.
Like you it seems that everything is working fine exept that the screen is totally black, and the brightness buttons don't change anything.

I don't have much too bring to you exept that if I boot on my "official" kernel 3.2 everything works. So maybe I did something wrong with the option (doubt that since I copy the options from 3.2) before compile 3.7 or it is a recent problem. Do you have older kernel to test with than 3.8 ?
Anycase we might consider report as a bug to the radeon team.

Last edited by aximab (2013-03-29 15:23:39)

Offline

#5 2013-03-29 18:48:16

damdim
Member
Registered: 2010-03-13
Posts: 48

Re: Hybrid graphics i915/radeon. Switch to radeon results to black screen

I have tried linux-lts 3.0.70 with a similar effect. Instead of the sceen turning off, it just freezes.
I will report to kernel bugzilla, and report the link here.

Offline

#6 2013-03-29 18:57:52

damdim
Member
Registered: 2010-03-13
Posts: 48

Re: Hybrid graphics i915/radeon. Switch to radeon results to black screen

Offline

Board footer

Powered by FluxBB