You are not logged in.
- Topics: Active | Unanswered
#1 2013-08-26 19:00:00
- Naruni
- Member
- Registered: 2010-08-05
- Posts: 34
Smart SanDisk SDSSDP128G test aborted by host, invalid checksum
Hi folks. This is very frustrating to me and my google skills are failing.
The problem begins when my SSD activity light goes on, and the system freezes for about 15 seconds. dmesg shows this:
[ 44.462241] ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x6 frozen
[ 44.462399] ata1.00: failed command: READ FPDMA QUEUED
[ 44.462512] ata1.00: cmd 60/00:00:48:d0:88/01:00:00:00:00/40 tag 0 ncq 131072 in
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 44.462786] ata1.00: status: { DRDY }
[ 44.462862] ata1.00: failed command: READ FPDMA QUEUED
[ 44.462971] ata1.00: cmd 60/00:08:48:cf:88/01:00:00:00:00/40 tag 1 ncq 131072 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 44.463242] ata1.00: status: { DRDY }
[ 44.463321] ata1: hard resetting link
[ 44.949030] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 44.949895] ata1.00: configured for UDMA/133
[ 44.949911] ata1.00: device reported invalid CHS sector 0
[ 44.949917] ata1.00: device reported invalid CHS sector 0
[ 44.949959] ata1: EH completesmartctl -a /dev/sda
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.10.9-1-ARCH] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: SanDisk SDSSDP128G
Serial Number: 131237402993
LU WWN Device Id: 5 001b44 999f0d571
Firmware Version: 2.0.0
User Capacity: 128,035,676,160 bytes [128 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 T13/2015-D revision 3
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Mon Aug 26 11:49:31 2013 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 25) The self-test routine was aborted by
the host.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x51) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 24) minutes.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0002 100 100 000 Old_age Always - 0
9 Power_On_Hours 0x0002 100 100 000 Old_age Always - 1611
12 Power_Cycle_Count 0x0002 100 100 000 Old_age Always - 27
171 Unknown_Attribute 0x0002 100 100 000 Old_age Always - 0
172 Unknown_Attribute 0x0002 100 100 000 Old_age Always - 0
173 Unknown_Attribute 0x0002 100 100 000 Old_age Always - 1
174 Unknown_Attribute 0x0002 100 100 000 Old_age Always - 6
187 Reported_Uncorrect 0x0002 100 100 000 Old_age Always - 0
230 Unknown_SSD_Attribute 0x0002 100 100 000 Old_age Always - 3
232 Available_Reservd_Space 0x0003 100 100 005 Pre-fail Always - 0
234 Unknown_Attribute 0x0002 100 100 000 Old_age Always - 12
241 Total_LBAs_Written 0x0002 100 100 000 Old_age Always - 461322364
242 Total_LBAs_Read 0x0002 100 100 000 Old_age Always - 437325123
SMART Error Log Version: 1
No Errors Logged
Warning! SMART Self-Test Log Structure error: invalid SMART checksum.
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Aborted by host 90% 1610 -
# 2 Short offline Aborted by host 90% 1610 -
# 3 Short offline Aborted by host 90% 1610 -
# 4 Short offline Aborted by host 90% 1610 -
# 5 Extended offline Aborted by host 90% 1596 -
# 6 Short offline Aborted by host 90% 1596 -
# 7 Extended offline Completed without error 00% 85 -
# 8 Extended offline Aborted by host 90% 85 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.Is this a SATA controller error or is this a SSD error?
I have set hdparm device standby timeout to 251 so it's not a standby issue. I'm out of gas here and could use some advice oer being pointed in the right direction.
Thanks for the help!
Offline
#2 2013-08-28 05:27:27
- Naruni
- Member
- Registered: 2010-08-05
- Posts: 34
Re: Smart SanDisk SDSSDP128G test aborted by host, invalid checksum
Nothing?
Am I in the wrong forum?
Offline
#3 2013-09-02 20:28:37
- Naruni
- Member
- Registered: 2010-08-05
- Posts: 34
Re: Smart SanDisk SDSSDP128G test aborted by host, invalid checksum
Bump
Offline
#4 2013-09-03 00:17:28
- WonderWoofy
- Member
- From: Los Gatos, CA
- Registered: 2012-05-19
- Posts: 8,414
Re: Smart SanDisk SDSSDP128G test aborted by host, invalid checksum
I'm not sure how your google skill can be inadequate in finding info about this. I just copy and pasted the "failed command: READ FPDMA QUEUED" (chosen simply because it is in all caps), and got all kinds of stuff… even stuff in this very forum.
So instead of just bumping your post over and over again, do a little searching and see what you can find.
BTW, back up your data ASAP.
Offline
#5 2013-09-03 14:25:14
- R00KIE
- Forum Fellow
- From: Between a computer and a chair
- Registered: 2008-09-14
- Posts: 4,734
Re: Smart SanDisk SDSSDP128G test aborted by host, invalid checksum
I'd say first backup all data like WonderWoofy said. After that I would try not changing anything, don't use hdparm to change any APM or standby timeouts, SSDs don't use as much power as spinning disks, they don't have heads to park which cause wear so leave that alone, those settings might not even get enough testing anymore.
After that I would try changing the data cable if the one you are using is some no-name/no-brand cable that you don't know where it came from.
Also try to reroute the data cable away from possible sources of interference such as power supply cables to big power users such as graphics cards and the cpu voltage step down circuitry (these might be the biggest offenders in terms of radiated noise. From my little personal experience this might not help much, also sata cables with differential signaling should be mostly immune to external noise sources).
Check if there is any firmware update for the SSD, although linux is almost always not supported, some problem with windows might prompt a firmware update that also fixes things for you.
The last resort option, if possible, is to use some tool provided by the ssd manufacturer to reduce the bus data transfer rate as it might help the disk+board to deal with whatever is causing problems.
The post last resort option is to try and get some help with the disk manufacturer, if they have some boot cd or standalone utility use that to test the disk. I suppose contacting them and saying "I'm using linux and I'm having this problem ....." will get you nowhere.
R00KIE
Tm90aGluZyB0byBzZWUgaGVyZSwgbW92ZSBhbG9uZy4K
Offline