I have just got this keyboard (G510) and have installed g15daemon-svn, libg15-svn, libg15render-svn and g15composer-svn from the AUR.
When running the g15daemon, I get mixed results: the keyboard LCD screen works and displays the time as it should but the "G" keys are not working as separate buttons.
G[1-12] act as the corresponding "F" buttons and G[13-18] act as [1-6] respectively as they do without the g15daemon running.
Running "g15daemon -d" gives the following output:
libg15: libg15 1.3 libg15: Found 1 supported devices libg15: Trying to find Logitech G15 libg15: Logitech G15 not found libg15: Trying to find Logitech G11 libg15: Logitech G11 not found libg15: Trying to find Logitech Z-10 libg15: Logitech Z-10 not found libg15: Trying to find Logitech G15 v2 libg15: Logitech G15 v2 not found libg15: Trying to find Logitech Gamepanel libg15: Logitech Gamepanel not found libg15: Trying to find Logitech G13 libg15: Logitech G13 not found libg15: Trying to find Logitech G110 libg15: Logitech G110 not found libg15: Trying to find Logitech G510 libg15: Found Logitech G510, trying to open it libg15: Device has 1 possible configurations libg15: Device has 1 Alternate Settings libg15: Interface 1 has 2 Endpoints libg15: Trying to detach driver currently attached: "dummy" libg15: Success, detached the driver libg15: Found "Extra Keys" endpoint 2 with address 0x82 maxtransfersize=8 libg15: Found "LCD" endpoint 3 with address 0x3 maxtransfersize=64 libg15: Done opening the keyboard g15daemon 1.2svn loaded
Which looks like there are no errors.
Is anyone using the G510 keyboard with the g15daemon-svn package, and if so does it work for you?
If it does work then it means that I am being a noob and have forgotten to change some keyboard setting somewhere!
Hey, did you eventually get it working?
When trying to install AUR/gnome15 I get this message:
==> Continue building gnome15 ? [Y/n] ==> --------------------------------- ==> ==> Building and installing package ==> Install or build missing dependencies for gnome15: [sudo] password for kdd: error: target not found: python2-uinput error: target not found: python2-virtkey error: target not found: lg4l ==> Restart building gnome15 ? [y/N]
Anyone figured this out?
Last edited by kinleyd (2014-04-08 04:36:43)
Did you read the comments of the gnome15 package? This is an old thread. Something like this might be better addressed in a new thread perhaps?
Last edited by nullified (2014-04-08 04:46:00)
"We may say most aptly, that the Analytical Engine weaves algebraical patterns just as the Jacquard-loom weaves flowers and leaves." - Ada Lovelace
Thanks for responding. Yes, I did read the comments on the package. I saw the bit about modifying the build but that seemed more like a hack rather than a permanent fix. At the moment my keyboard is working at the default settings (media keys, etc.) so I'm not under pressure to fix it. Over time I would like to get the keyboard panel, etc. to do their job.
I am going to use this opportunity to close this thread. Nothing wrong, it is just that the thread is a bit old. If this conversation needs to continue, please go ahead and start a fresh thread.
Nothing is too wonderful to be true, if it be consistent with the laws of nature -- Michael Faraday
You assume people are rational and influenced by evidence. You must not work with the public much. -- Trilby
How to Ask Questions the Smart Way