You are not logged in.
Pages: 1
Hello everybody, I've tried looking in other threads about this issue and haven't had any luck solving this.
Basically I have attempted to put Arch Linux onto my HP Pavilion laptop following the beginners guide to installing Arch.
The process has gone somewhat smoothly, I've set up the partitions, installed, configs etc and I downloaded the 'iw wpa_supplicant dialog' as it tells me to.
However I've managed to boot into Arch onto laptop and enter 'wifi-menu' but it just comes out with:
'Scanning for networks......failed'
'No networks found'
I'm unsure on what I should do about this in order to make it connect to the internet. Any help or advice will be greatly appreciated.
Offline
We have had a similar problem a few days ago:
https://bbs.archlinux.org/viewtopic.php?id=213788
"Yesterday is history, tomorrow is a mystery, but today is a gift. That is why it is called the present." - Master Oogway
Offline
We have had a similar problem a few days ago:
https://bbs.archlinux.org/viewtopic.php?id=213788
I've attempted the solution on that thread, I made some progress as it actually scans for networks now which seems to be a good sign, however when I attempt to connect to my network it gives me an error that says:
job for netctl@wlo1\x2dBTHub\x2dGJ53.service failed because the control process exited with error code.
See "systemctl status "netctl@wlo1\x2dBTHub\x2dGJ53.service"" and "journalctl -xe" for details.
When I enter:
"systemctl status "netctl@wlo1\x2dBTHub\x2dGJ53.service""
It comes up with:
netctl@wlo1\x2dBTHub\x2dGJ53.service - Networking for netctl profile wlo1-BTHub-GJ53
Loaded: loaded (/usr/lib/systemd/system/netctl@.service; static; vendor preset: disabled)
Active: failed (Result: exit-code) since Wed 2016-06-22 20:23:33 UTC; 4min 50s ago
Docs: man:netctl.profile(5)
Process: 613 ExecStart=/usr/lib/network/network start %I (code=exited, status=1/FAILURE)
Main PID: 613 (code=exited, status=1/FAILURE)
Jun 22 20:23:33 Toby systemd[1] Starting Network for netctl profile wlo1-BTHub5-GJ53. . .
Jun 22 20:23:33 Toby systemd[1] netctl@wlo1\x2dBTHub\x2dGJ53.service: Main process exited, code=exited, status=1/FAILURE
Jun 22 20:23:33 Toby network[613] Starting network profile 'wlo1-BTHub5-GJ53'
Jun 22 20:23:33 Toby network[613] THe interface of the network profile 'wlo1-BTHub53' is already up
Jun 22 20:23:33 Toby systemd[1] Failed to start Networking for netctl profile wlo1-BTHub5-GJ53.
Jun 22 20:23:33 Toby systemd[1]netctl@wlo1\x2dBTHub\x2dGJ53.service: Unit entered failed state
Jun 22 20:23:33 Toby systemd[1]netctl@wlo1\x2dBTHub\x2dGJ53.service Failed with result 'exit-code'.
Offline
That's the problem:
Jun 22 20:23:33 Toby network[613] THe interface of the network profile 'wlo1-BTHub53' is already up
Set your interface down through
ip link set <blabla> down
and *then* try to connect with netctl.
See also: https://wiki.archlinux.org/index.php/ne … ice_failed
Last edited by Starfish (2016-06-23 09:38:52)
"Yesterday is history, tomorrow is a mystery, but today is a gift. That is why it is called the present." - Master Oogway
Offline
Pages: 1