You are not logged in.

Pages: 1

#1 2019-03-04 18:16:14

Terraman
Member
Registered: 2019-03-02
Posts: 11

[SOLVED] WiFi can not connect

Hi,

I'm using Arch for a while, but I can't connect internet trough wifi. So, I want to fix the issue. I'm using Openbox without a display manager. I also followed all the Arch wikis and also searched the internet and I could'nt solve the issue so far. Before Arch, I was using Debian with the same configuration and wifi had worked fine.

The ouput of:

$  lspci -K
02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01)
	Subsystem: Foxconn International, Inc. T77H126.00 802.11bgn Wireless Half-size Mini PCIe Card
	Kernel driver in use: ath9k
	Kernel modules: ath9k
$ iw dev
phy#0
	Interface wlp2s0
		ifindex 3
		wdev 0x1
		addr 6e:1d:3a:6f:ec:87
		type managed
		txpower 14.00 dBm
		multicast TXQ:
			qsz-byt	qsz-pkt	flows	drops	marks	overlmt	hashcol	tx-bytes	tx-packets
			0	0	0	0	0	0	0	0		0
# iw dev wlp2s0 link
Not connected.
# ip link set wlp2s0 up
# ip link show wlp2s0
3: wlp2s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN mode DORMANT group default qlen 1000
    link/ether 4e:c3:bc:d2:31:00 brd ff:ff:ff:ff:ff:ff
#  iw dev wlp2s0 scan | less
BSS 00:0c:43:76:20:89(on wlp2s0)
	TSF: 2476893624912 usec (28d, 16:01:33)
	freq: 2417
	beacon interval: 100 TUs
	capability: ESS ShortPreamble ShortSlotTime (0x0421)
	signal: -35.00 dBm
	last seen: 384 ms ago
	Information elements from Probe Response frame:
	SSID: OpenWrt
	Supported rates: 1.0* 2.0* 5.5* 11.0* 6.0 9.0 12.0 18.0 
	DS Parameter set: channel 2
	Country: PL	Environment: Indoor/Outdoor
		Channels [1 - 13] @ 20 dBm
	ERP: <no flags>
	Extended supported rates: 24.0 36.0 48.0 54.0 
	HT capabilities:
		Capabilities: 0x2ec
			HT20
			SM Power Save disabled
			RX HT20 SGI
			RX HT40 SGI
			TX STBC
			RX STBC 2-streams
			Max AMSDU length: 3839 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 2 usec (0x04)
		HT RX MCS rate indexes supported: 0-15, 32
		TX unequal modulation not supported
		HT TX Max spatial streams: 2
		HT TX MCS rate indexes supported may differ
	HT operation:
		 * primary channel: 2
		 * secondary channel offset: above
		 * STA channel width: any
		 * RIFS: 0
		 * HT protection: 20 MHz
		 * non-GF present: 1
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Extended capabilities:
		 * Operating Mode Notification
	WMM:	 * Parameter version 1
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
# iw dev wlp2s0 connect OpenWrt
# iw dev wlp2s0 link
Not connected.

I'm sure that it's something that I'm overlooking or missing.

Thank's in advance!

Herman

Last edited by Terraman (2019-03-05 01:00:38)

Offline

#2 2019-03-04 18:32:14

2ManyDogs
Forum Fellow
Registered: 2012-01-15
Posts: 4,648

Re: [SOLVED] WiFi can not connect

I also followed all the Arch wikis and also searched the internet and I could'nt solve the issue so far.

This tells us nothing. What exactly have you tried? Post exact commands and their output.

https://wiki.archlinux.org/index.php/Wi … figuration
https://bbs.archlinux.org/viewtopic.php?id=57855

How To Ask Questions The Smart Way

Moving to Newbie Corner.

Offline

#3 2019-03-04 18:49:15

Terraman
Member
Registered: 2019-03-02
Posts: 11

Re: [SOLVED] WiFi can not connect

2ManyDogs wrote:

I also followed all the Arch wikis and also searched the internet and I could'nt solve the issue so far.

This tells us nothing. What exactly have you tried? Post exact commands and their output.

https://wiki.archlinux.org/index.php/Wi … figuration
https://bbs.archlinux.org/viewtopic.php?id=57855

How To Ask Questions The Smart Way

Moving to Newbie Corner.

Yes, sorry, I submitted erroneously before I have finished the post.

Herman

Offline

#4 2019-03-04 18:53:37

seth
Member
From: Won't reply 2 private help req
Registered: 2012-09-03
Posts: 78,600

Re: [SOLVED] WiFi can not connect

Try "connect -w" and also monitor "dmesg -w" in parallel.

How to upload text · How to boot w/o GUI · Disable Windows Fast-Start! · Fix your xinitrc

Offline

#5 2019-03-04 19:16:04

Terraman
Member
Registered: 2019-03-02
Posts: 11

Re: [SOLVED] WiFi can not connect

seth wrote:

Try "connect -w" and also monitor "dmesg -w" in parallel.

Can you explain me how should I do this?

Thanks, Herman

Offline

#6 2019-03-04 19:30:58

seth
Member
From: Won't reply 2 private help req
Registered: 2012-09-03
Posts: 78,600

Re: [SOLVED] WiFi can not connect

Hah?
You run "dmesg -w" in one terminal and "iw dev wlp2s0 connect -w OpenWrt" in another. The following dmesg is just for convenience, so you can see relevant kernel level reactions immediately.

How to upload text · How to boot w/o GUI · Disable Windows Fast-Start! · Fix your xinitrc

Offline

#7 2019-03-04 19:59:25

Terraman
Member
Registered: 2019-03-02
Posts: 11

Re: [SOLVED] WiFi can not connect

seth wrote:

Hah?
You run "dmesg -w" in one terminal and "iw dev wlp2s0 connect -w OpenWrt" in another. The following dmesg is just for convenience, so you can see relevant kernel level reactions immediately.

Ok!
Thats the output:

iw dev wlp2s0 connect -w OpenWrt
connected to 00:0c:43:76:20:89

And:

dmesg -w
[12809.357658] wlp2s0: authenticate with 00:0c:43:76:20:89
[12809.376742] wlp2s0: send auth to 00:0c:43:76:20:89 (try 1/3)
[12809.379843] wlp2s0: authenticated
[12809.384896] wlp2s0: associate with 00:0c:43:76:20:89 (try 1/3)
[12809.388526] wlp2s0: RX AssocResp from 00:0c:43:76:20:89 (capab=0x421 status=0 aid=2)
[12809.388757] wlp2s0: associated
[12809.390555] wlp2s0: deauthenticating from 00:0c:43:76:20:89 by local choice (Reason: 3=DEAUTH_LEAVING)

Still no internet trough wifi available.

Offline

#8 2019-03-04 20:13:02

seth
Member
From: Won't reply 2 private help req
Registered: 2012-09-03
Posts: 78,600

Re: [SOLVED] WiFi can not connect

You associate and then do something on the client to immediately cut the connection.

systemctl list-unit-files --state=enabled

How to upload text · How to boot w/o GUI · Disable Windows Fast-Start! · Fix your xinitrc

Offline

#9 2019-03-04 20:31:05

Terraman
Member
Registered: 2019-03-02
Posts: 11

Re: [SOLVED] WiFi can not connect

seth wrote:

You associate and then do something on the client to immediately cut the connection.

systemctl list-unit-files --state=enabled

There's the output:

systemctl list-unit-files --state=enabled
UNIT FILE                                   STATE  
org.cups.cupsd.path                         enabled
autofs.service                              enabled
autovt@.service                             enabled
dbus-org.freedesktop.NetworkManager.service enabled
dbus-org.freedesktop.nm-dispatcher.service  enabled
dbus-org.wicd.daemon.service                enabled
dhcpcd.service                              enabled
getty@.service                              enabled
NetworkManager-dispatcher.service           enabled
NetworkManager-wait-online.service          enabled
NetworkManager.service                      enabled
org.cups.cupsd.service                      enabled
wicd.service                                enabled
org.cups.cupsd.socket                       enabled
remote-fs.target                            enabled

15 unit files listed.

Offline

#10 2019-03-04 20:33:25

seth
Member
From: Won't reply 2 private help req
Registered: 2012-09-03
Posts: 78,600

Re: [SOLVED] WiFi can not connect

dhcpcd.service                              enabled
NetworkManager.service                      enabled
wicd.service                                enabled

So you have *three* network managing services enabled and attempt a manual connection on top… m(

How did you install archlinux?

How to upload text · How to boot w/o GUI · Disable Windows Fast-Start! · Fix your xinitrc

Offline

#11 2019-03-04 20:50:17

Terraman
Member
Registered: 2019-03-02
Posts: 11

Re: [SOLVED] WiFi can not connect

seth wrote:
dhcpcd.service                              enabled
NetworkManager.service                      enabled
wicd.service                                enabled

So you have *three* network managing services enabled and attempt a manual connection on top… m(

How did you install archlinux?

I have installed Archlinux according to the Archlinux wikis. But, I haven't wifi from the beginning, so I have tried many solutions from my search in the net... Maybe thats the problem...

Offline

#12 2019-03-04 20:59:16

jasonwryan
Anarchist
From: .nz
Registered: 2009-05-09
Posts: 30,426
Website

Re: [SOLVED] WiFi can not connect

Read the Note: https://wiki.archlinux.org/index.php/Ne … k_managers

Arch + dwm   •   Mercurial repos  •   Surfraw

Registered Linux User #482438

Offline

#13 2019-03-04 22:32:10

Terraman
Member
Registered: 2019-03-02
Posts: 11

Re: [SOLVED] WiFi can not connect

Thank you seth and jasonwryan,

I disable wicd and networkmanager services and after reboot, wifi is functioning.

So, it's solved.

Herman

Offline

#14 2019-03-04 22:59:37

jasonwryan
Anarchist
From: .nz
Registered: 2009-05-09
Posts: 30,426
Website

Re: [SOLVED] WiFi can not connect

Please remember to mark your thread as [Solved] by editing your first post and prepending it to the title.

Arch + dwm   •   Mercurial repos  •   Surfraw

Registered Linux User #482438

Offline

Pages: 1

Board footer

Powered by FluxBB