You are not logged in.

#1 2019-07-02 07:16:19

Portal
Member
Registered: 2019-03-11
Posts: 48

cannot run smartctl on drive

I am trying to run a smart test on my suspected failed drive. I ran:

sudo smartctl -t short /dev/sda

but that returns the error:

=== START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION ===
Sending command: "Execute SMART Short self-test routine immediately in off-line mode".
Command "Execute SMART Short self-test routine immediately in off-line mode" failed: scsi error badly formed scsi parameters

Since the drive is sata, not scsi, I tried to add the extra "device" parameter:

sudo smartctl -t short /dev/sda --device=ata

but this returns the error:

=== START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION ===
Sending command: "Execute SMART Short self-test routine immediately in off-line mode".
Command "Execute SMART Short self-test routine immediately in off-line mode" failed: Input/output error

what should I do?

Offline

#2 2019-07-02 10:39:04

seth
Member
Registered: 2012-09-03
Posts: 58,672

Re: cannot run smartctl on drive

Is the device smart capable at all?
Output of

sudo smartctl -a /dev/sda
dmesg

?

Online

#3 2019-07-02 12:37:10

Portal
Member
Registered: 2019-03-11
Posts: 48

Re: cannot run smartctl on drive

The device is smart-capable

smartctl -a /dev/sda

gives

smartctl 6.6 2017-11-05 r4594 [x86_64-linux-5.0.0-13-generic] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     TOSHIBA MQ01ACF050
Serial Number:    17NLTLB9T
LU WWN Device Id: 5 000039 781a091ba
Firmware Version: AV002D
User Capacity:    500,107,862,016 bytes [500 GB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      2.5 inches
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   ATA8-ACS (minor revision not indicated)
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Tue Jul  2 12:18:28 2019 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x80) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever 
                                        been run.
Total time to complete Offline 
data collection:                (  120) seconds.
Offline data collection
capabilities:                    (0x5b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine 
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        (   0) minutes.
SCT capabilities:              (0x003d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 128
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   100   050    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   100   100   001    Pre-fail  Always       -       1979
  5 Reallocated_Sector_Ct   0x0033   100   100   050    Pre-fail  Always       -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       3
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       8
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       0
193 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       -       456
194 Temperature_Celsius     0x0022   100   100   000    Old_age   Always       -       30 (Min/Max 23/33)
199 UDMA_CRC_Error_Count    0x0032   200   253   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0032   100   100   000    Old_age   Always       -       0
241 Total_LBAs_Written      0x0032   100   100   000    Old_age   Always       -       2752
242 Total_LBAs_Read         0x0032   100   100   000    Old_age   Always       -       288936
254 Free_Fall_Sensor        0x0032   100   100   000    Old_age   Always       -       0

SMART Error Log Version: 1
ATA Error Count: 40 (device log contains only the most recent five errors)
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 40 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 50 01 01 00 00 00

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  aa aa aa aa aa aa aa ff      00:21:29.893  [RESERVED]
  35 00 60 08 a0 ee e0 00      00:21:29.834  WRITE DMA EXT
  25 00 08 00 a0 72 e0 00      00:21:29.828  READ DMA EXT
  25 00 08 18 c1 ee e0 00      00:21:29.823  READ DMA EXT
  25 00 00 e0 a0 ee e0 00      00:21:29.814  READ DMA EXT

Error 39 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 50 01 01 00 00 00

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  aa aa aa aa aa aa aa ff      00:21:26.742  [RESERVED]
  35 00 08 18 e6 34 e0 00      00:21:26.674  WRITE DMA EXT
  ef 10 02 00 00 00 a0 00      00:21:26.673  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 a0 00      00:21:26.672  IDENTIFY DEVICE
  ef 03 45 00 00 00 a0 00      00:21:26.672  SET FEATURES [Set transfer mode]

Error 38 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 50 01 01 00 00 00

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  aa aa aa aa aa aa aa ff      00:21:26.042  [RESERVED]
  35 00 08 58 aa 2e e0 00      00:21:26.014  WRITE DMA EXT
  ef 10 02 00 00 00 a0 00      00:21:26.013  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 a0 00      00:21:26.012  IDENTIFY DEVICE
  ef 03 45 00 00 00 a0 00      00:21:26.012  SET FEATURES [Set transfer mode]

Error 37 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 50 01 01 00 00 00

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  aa aa aa aa aa aa aa ff      00:21:25.392  [RESERVED]
  35 00 18 58 a9 2e e0 00      00:21:25.324  WRITE DMA EXT
  ef 10 02 00 00 00 a0 00      00:21:25.323  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 a0 00      00:21:25.322  IDENTIFY DEVICE
  ef 03 45 00 00 00 a0 00      00:21:25.322  SET FEATURES [Set transfer mode]

Error 36 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 50 01 01 00 00 00

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  aa aa aa aa aa aa aa ff      00:21:22.213  [RESERVED]
  aa aa aa aa aa aa aa ff      00:21:22.183  [RESERVED]
  25 00 40 40 e3 1f 40 00      00:21:20.185  READ DMA EXT
  25 00 40 00 e3 1f 40 00      00:21:20.177  READ DMA EXT
  25 00 40 c0 e2 1f 40 00      00:21:20.168  READ DMA EXT

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%      2016         -
# 2  Short offline       Completed without error       00%      2009         -
# 3  Extended offline    Completed without error       00%      1987         -
# 4  Short offline       Completed without error       00%      1985         -
# 5  Short offline       Completed without error       00%      1976         -
# 6  Short offline       Completed without error       00%      1959         -
# 7  Short offline       Completed without error       00%      1943         -
# 8  Extended offline    Completed without error       00%      1940         -
# 9  Extended offline    Aborted by host               70%      1929         -
#10  Short offline       Completed without error       00%      1905         -
#11  Short offline       Completed without error       00%      1881         -
#12  Short offline       Completed without error       00%      1857         -
#13  Short offline       Completed without error       00%      1847         -
#14  Short offline       Completed without error       00%      1823         -
#15  Short offline       Aborted by host               30%      1809         -
#16  Extended offline    Completed without error       00%      1802         -
#17  Short offline       Completed without error       00%      1800         -
#18  Short offline       Completed without error       00%      1776         -
#19  Short offline       Completed without error       00%      1752         -
#20  Short offline       Completed without error       00%      1728         -
#21  Short offline       Completed without error       00%      1704         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
dmesg

gives

[    0.000000] microcode: microcode updated early to revision 0x9a, date = 2018-07-16
[    0.000000] Linux version 5.0.0-13-generic (buildd@lcy01-amd64-020) (gcc version 8.3.0 (Ubuntu 8.3.0-6ubuntu1)) #14-Ubuntu SMP Mon Apr 15 14:59:14 UTC 2019 (Ubuntu 5.0.0-13.14-generic 5.0.6)
[    0.000000] Command line: BOOT_IMAGE=/casper/vmlinuz file=/cdrom/preseed/kubuntu.seed boot=casper maybe-ubiquity quiet splash ---
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   Hygon HygonGenuine
[    0.000000]   Centaur CentaurHauls
[    0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x008: 'MPX bounds registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x010: 'MPX CSR'
[    0.000000] x86/fpu: xstate_offset[2]:  576, xstate_sizes[2]:  256
[    0.000000] x86/fpu: xstate_offset[3]:  832, xstate_sizes[3]:   64
[    0.000000] x86/fpu: xstate_offset[4]:  896, xstate_sizes[4]:   64
[    0.000000] x86/fpu: Enabled xstate features 0x1f, context size is 960 bytes, using 'compacted' format.
[    0.000000] BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x0000000000057fff] usable
[    0.000000] BIOS-e820: [mem 0x0000000000058000-0x0000000000058fff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000059000-0x000000000009efff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009f000-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000ba645fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000ba646000-0x00000000ba646fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000ba647000-0x00000000ba647fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ba648000-0x00000000ca339fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000ca33a000-0x00000000ca6b0fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ca6b1000-0x00000000ca708fff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000ca709000-0x00000000caff3fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000caff4000-0x00000000cb589fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000cb58a000-0x00000000cb5fefff] type 20
[    0.000000] BIOS-e820: [mem 0x00000000cb5ff000-0x00000000cb5fffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000f0000000-0x00000000f7ffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fe000000-0x00000000fe010fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000052e7fffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] efi: EFI v2.40 by American Megatrends
[    0.000000] efi:  ACPI=0xca6d3000  ACPI 2.0=0xca6d3000  SMBIOS=0xf05e0  SMBIOS 3.0=0xf0600  ESRT=0xcb35c598  MPS=0xfcba0 
[    0.000000] secureboot: Secure boot could not be determined (mode 0)
[    0.000000] SMBIOS 3.0.0 present.
[    0.000000] DMI: Dell Inc. Precision 3520/0C7J6P, BIOS 1.1.1 01/17/2017
[    0.000000] tsc: Detected 2800.000 MHz processor
[    0.002224] tsc: Detected 2808.000 MHz TSC
[    0.002224] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.002226] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.002233] last_pfn = 0x52e800 max_arch_pfn = 0x400000000
[    0.002237] MTRR default type: write-back
[    0.002238] MTRR fixed ranges enabled:
[    0.002239]   00000-9FFFF write-back
[    0.002240]   A0000-BFFFF uncachable
[    0.002241]   C0000-FFFFF write-protect
[    0.002241] MTRR variable ranges enabled:
[    0.002243]   0 base 00E0000000 mask 7FE0000000 uncachable
[    0.002243]   1 base 00D0000000 mask 7FF0000000 uncachable
[    0.002244]   2 base 00CE000000 mask 7FFE000000 uncachable
[    0.002245]   3 base 00CD000000 mask 7FFF000000 uncachable
[    0.002245]   4 disabled
[    0.002246]   5 disabled
[    0.002246]   6 disabled
[    0.002247]   7 disabled
[    0.002247]   8 disabled
[    0.002248]   9 disabled
[    0.003161] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT  
[    0.003319] last_pfn = 0xcb600 max_arch_pfn = 0x400000000
[    0.012115] found SMP MP-table at [mem 0x000fce00-0x000fce0f] mapped at [(____ptrval____)]
[    0.012129] esrt: Reserving ESRT space from 0x00000000cb35c598 to 0x00000000cb35c5d0.
[    0.012136] check: Scanning 1 areas for low memory corruption
[    0.012139] Base memory trampoline at [(____ptrval____)] 96000 size 24576
[    0.012142] Using GB pages for direct mapping
[    0.012144] BRK [0x15bc01000, 0x15bc01fff] PGTABLE
[    0.012146] BRK [0x15bc02000, 0x15bc02fff] PGTABLE
[    0.012147] BRK [0x15bc03000, 0x15bc03fff] PGTABLE
[    0.012196] BRK [0x15bc04000, 0x15bc04fff] PGTABLE
[    0.012198] BRK [0x15bc05000, 0x15bc05fff] PGTABLE
[    0.012440] BRK [0x15bc06000, 0x15bc06fff] PGTABLE
[    0.012481] BRK [0x15bc07000, 0x15bc07fff] PGTABLE
[    0.012559] BRK [0x15bc08000, 0x15bc08fff] PGTABLE
[    0.012618] BRK [0x15bc09000, 0x15bc09fff] PGTABLE
[    0.012693] BRK [0x15bc0a000, 0x15bc0afff] PGTABLE
[    0.012786] RAMDISK: [mem 0x32f37000-0x35792fff]
[    0.012794] ACPI: Early table checksum verification disabled
[    0.012797] ACPI: RSDP 0x00000000CA6D3000 000024 (v02 DELL  )
[    0.012801] ACPI: XSDT 0x00000000CA6D30C0 0000FC (v01 DELL   CBX3     01072009 AMI  00010013)
[    0.012806] ACPI: FACP 0x00000000CA6F8378 00010C (v05 DELL   CBX3     01072009 AMI  00010013)
[    0.012811] ACPI: DSDT 0x00000000CA6D3248 02512F (v02 DELL   CBX3     01072009 INTL 20160422)
[    0.012814] ACPI: FACS 0x00000000CAFECF80 000040
[    0.012817] ACPI: UEFI 0x00000000CA6F9000 00063A (v01 INTEL  RstSataE 00000000 ??   00000000)
[    0.012819] ACPI: APIC 0x00000000CA6F9640 000084 (v03 DELL   CBX3     01072009 AMI  00010013)
[    0.012822] ACPI: FPDT 0x00000000CA6F96C8 000044 (v01 DELL   CBX3     01072009 AMI  00010013)
[    0.012826] ACPI: FIDT 0x00000000CA6F9710 00009C (v01 DELL   CBX3     01072009 AMI  00010013)
[    0.012828] ACPI: MCFG 0x00000000CA6F97B0 00003C (v01 DELL   CBX3     01072009 MSFT 00000097)
[    0.012831] ACPI: HPET 0x00000000CA6F97F0 000038 (v01 DELL   CBX3     01072009 AMI. 0005000B)
[    0.012833] ACPI: SSDT 0x00000000CA6F9828 000572 (v01 SataRe SataTabl 00001000 INTL 20160422)
[    0.012836] ACPI: SSDT 0x00000000CA6F9DA0 0012DC (v02 SaSsdt SaSsdt   00003000 INTL 20160422)
[    0.012838] ACPI: SSDT 0x00000000CA6FB080 002A66 (v02 PegSsd PegSsdt  00001000 INTL 20160422)
[    0.012841] ACPI: HPET 0x00000000CA6FDAE8 000038 (v01 INTEL  KBL      00000001 MSFT 0000005F)
[    0.012844] ACPI: SSDT 0x00000000CA6FDB20 000CE8 (v02 INTEL  xh_rvp11 00000000 INTL 20160422)
[    0.012846] ACPI: UEFI 0x00000000CA6FE808 000042 (v01                 00000000      00000000)
[    0.012849] ACPI: SSDT 0x00000000CA6FE850 000EDE (v02 CpuRef CpuSsdt  00003000 INTL 20160422)
[    0.012851] ACPI: LPIT 0x00000000CA6FF730 000094 (v01 INTEL  KBL      00000000 MSFT 0000005F)
[    0.012854] ACPI: WSMT 0x00000000CA6FF7C8 000028 (v01 INTEL  KBL      00000000 MSFT 0000005F)
[    0.012856] ACPI: SSDT 0x00000000CA6FF7F0 00029F (v02 INTEL  sensrhub 00000000 INTL 20160422)
[    0.012859] ACPI: SSDT 0x00000000CA6FFA90 003002 (v02 INTEL  PtidDevc 00001000 INTL 20160422)
[    0.012861] ACPI: DBGP 0x00000000CA702A98 000034 (v01 INTEL           00000002 MSFT 0000005F)
[    0.012864] ACPI: DBG2 0x00000000CA702AD0 000054 (v00 INTEL           00000002 MSFT 0000005F)
[    0.012866] ACPI: SSDT 0x00000000CA702B28 005265 (v02 DptfTa DptfTabl 00001000 INTL 20160422)
[    0.012869] ACPI: MSDM 0x00000000CA707D90 000055 (v03 DELL   CBX3     06222004 AMI  00010013)
[    0.012871] ACPI: SLIC 0x00000000CA707DE8 000176 (v03 DELL   CBX3     01072009 MSFT 00010013)
[    0.012874] ACPI: DMAR 0x00000000CA707F60 0000F0 (v01 INTEL  KBL      00000001 INTL 00000001)
[    0.012876] ACPI: UEFI 0x00000000CA708050 00005C (v01 INTEL  RstSataV 00000000 ??   00000000)
[    0.012879] ACPI: ASF! 0x00000000CA7080B0 0000A0 (v32 INTEL   HCG     00000001 TFSM 000F4240)
[    0.012881] ACPI: BGRT 0x00000000CA708150 000038 (v00 \xf3\xee              01072009 AMI  00010013)
[    0.012889] ACPI: DMI detected: DELL Precision 3520 (force ACPI _REV to 5)
[    0.012890] ACPI: Local APIC address 0xfee00000
[    0.013081] No NUMA configuration found
[    0.013082] Faking a node at [mem 0x0000000000000000-0x000000052e7fffff]
[    0.013091] NODE_DATA(0) allocated [mem 0x52e7d5000-0x52e7fffff]
[    0.013291] Zone ranges:
[    0.013292]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.013293]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
[    0.013294]   Normal   [mem 0x0000000100000000-0x000000052e7fffff]
[    0.013295]   Device   empty
[    0.013296] Movable zone start for each node
[    0.013299] Early memory node ranges
[    0.013300]   node   0: [mem 0x0000000000001000-0x0000000000057fff]
[    0.013301]   node   0: [mem 0x0000000000059000-0x000000000009efff]
[    0.013301]   node   0: [mem 0x0000000000100000-0x00000000ba645fff]
[    0.013302]   node   0: [mem 0x00000000ba648000-0x00000000ca339fff]
[    0.013302]   node   0: [mem 0x00000000cb5ff000-0x00000000cb5fffff]
[    0.013303]   node   0: [mem 0x0000000100000000-0x000000052e7fffff]
[    0.013670] Zeroed struct page in unavailable ranges: 23850 pages
[    0.013671] Initmem setup node 0 [mem 0x0000000000001000-0x000000052e7fffff]
[    0.013672] On node 0 totalpages: 5212886
[    0.013674]   DMA zone: 64 pages used for memmap
[    0.013674]   DMA zone: 26 pages reserved
[    0.013675]   DMA zone: 3997 pages, LIFO batch:0
[    0.013782]   DMA32 zone: 12877 pages used for memmap
[    0.013783]   DMA32 zone: 824121 pages, LIFO batch:63
[    0.036197]   Normal zone: 68512 pages used for memmap
[    0.036198]   Normal zone: 4384768 pages, LIFO batch:63
[    0.148376] Reserving Intel graphics memory at [mem 0xcd800000-0xcf7fffff]
[    0.148873] ACPI: PM-Timer IO Port: 0x1808
[    0.148874] ACPI: Local APIC address 0xfee00000
[    0.148880] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.148881] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[    0.148881] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[    0.148882] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[    0.148909] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-119
[    0.148911] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.148912] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.148913] ACPI: IRQ0 used by override.
[    0.148914] ACPI: IRQ9 used by override.
[    0.148916] Using ACPI (MADT) for SMP configuration information
[    0.148917] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[    0.148926] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[    0.148942] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.148944] PM: Registered nosave memory: [mem 0x00058000-0x00058fff]
[    0.148945] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.148946] PM: Registered nosave memory: [mem 0x000a0000-0x000fffff]
[    0.148947] PM: Registered nosave memory: [mem 0xba646000-0xba646fff]
[    0.148948] PM: Registered nosave memory: [mem 0xba647000-0xba647fff]
[    0.148949] PM: Registered nosave memory: [mem 0xca33a000-0xca6b0fff]
[    0.148950] PM: Registered nosave memory: [mem 0xca6b1000-0xca708fff]
[    0.148950] PM: Registered nosave memory: [mem 0xca709000-0xcaff3fff]
[    0.148951] PM: Registered nosave memory: [mem 0xcaff4000-0xcb589fff]
[    0.148951] PM: Registered nosave memory: [mem 0xcb58a000-0xcb5fefff]
[    0.148952] PM: Registered nosave memory: [mem 0xcb600000-0xcd7fffff]
[    0.148953] PM: Registered nosave memory: [mem 0xcd800000-0xcf7fffff]
[    0.148954] PM: Registered nosave memory: [mem 0xcf800000-0xefffffff]
[    0.148954] PM: Registered nosave memory: [mem 0xf0000000-0xf7ffffff]
[    0.148955] PM: Registered nosave memory: [mem 0xf8000000-0xfdffffff]
[    0.148955] PM: Registered nosave memory: [mem 0xfe000000-0xfe010fff]
[    0.148956] PM: Registered nosave memory: [mem 0xfe011000-0xfebfffff]
[    0.148956] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[    0.148957] PM: Registered nosave memory: [mem 0xfec01000-0xfedfffff]
[    0.148957] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[    0.148958] PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
[    0.148958] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
[    0.148960] [mem 0xcf800000-0xefffffff] available for PCI devices
[    0.148961] Booting paravirtualized kernel on bare hardware
[    0.148963] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[    0.148972] random: get_random_bytes called from start_kernel+0x97/0x516 with crng_init=0
[    0.148978] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
[    0.149123] percpu: Embedded 46 pages/cpu @(____ptrval____) s151552 r8192 d28672 u524288
[    0.149129] pcpu-alloc: s151552 r8192 d28672 u524288 alloc=1*2097152
[    0.149130] pcpu-alloc: [0] 0 1 2 3 
[    0.149151] Built 1 zonelists, mobility grouping on.  Total pages: 5131407
[    0.149151] Policy zone: Normal
[    0.149153] Kernel command line: BOOT_IMAGE=/casper/vmlinuz file=/cdrom/preseed/kubuntu.seed boot=casper maybe-ubiquity quiet splash ---
[    0.152874] Calgary: detecting Calgary via BIOS EBDA area
[    0.152876] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.195803] Memory: 20097164K/20851544K available (14339K kernel code, 2334K rwdata, 4292K rodata, 2576K init, 5204K bss, 754380K reserved, 0K cma-reserved)
[    0.195913] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.195918] Kernel/User page tables isolation: enabled
[    0.195932] ftrace: allocating 41532 entries in 163 pages
[    0.213754] rcu: Hierarchical RCU implementation.
[    0.213756] rcu: 	RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=4.
[    0.213757] 	Tasks RCU enabled.
[    0.213758] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.213758] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.216589] NR_IRQS: 524544, nr_irqs: 1024, preallocated irqs: 16
[    0.216911] Console: colour dummy device 80x25
[    0.216915] printk: console [tty0] enabled
[    0.216928] ACPI: Core revision 20181213
[    0.217158] ACPI: Overriding _REV return value to 5
[    0.217300] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635855245 ns
[    0.217330] hpet clockevent registered
[    0.217367] APIC: Switch to symmetric I/O mode setup
[    0.217369] DMAR: Host address width 39
[    0.217370] DMAR: DRHD base: 0x000000fed90000 flags: 0x0
[    0.217375] DMAR: dmar0: reg_base_addr fed90000 ver 1:0 cap 1c0000c40660462 ecap 19e2ff0505e
[    0.217376] DMAR: DRHD base: 0x000000fed91000 flags: 0x1
[    0.217380] DMAR: dmar1: reg_base_addr fed91000 ver 1:0 cap d2008c40660462 ecap f050da
[    0.217381] DMAR: RMRR base: 0x000000ca402000 end: 0x000000ca421fff
[    0.217382] DMAR: RMRR base: 0x000000cd000000 end: 0x000000cf7fffff
[    0.217383] DMAR: ANDD device: 1 name: \_SB.PCI0.I2C0
[    0.217383] DMAR: ANDD device: 2 name: \_SB.PCI0.I2C1
[    0.217385] DMAR-IR: IOAPIC id 2 under DRHD base  0xfed91000 IOMMU 1
[    0.217386] DMAR-IR: HPET id 0 under DRHD base 0xfed91000
[    0.217386] DMAR-IR: Queued invalidation will be enabled to support x2apic and Intr-remapping.
[    0.218901] DMAR-IR: Enabled IRQ remapping in x2apic mode
[    0.218903] x2apic enabled
[    0.218917] Switched APIC routing to cluster x2apic.
[    0.222958] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.241341] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x2879c5f06f2, max_idle_ns: 440795220049 ns
[    0.241353] Calibrating delay loop (skipped), value calculated using timer frequency.. 5616.00 BogoMIPS (lpj=11232000)
[    0.241355] pid_max: default: 32768 minimum: 301
[    0.250365] LSM: Security Framework initializing
[    0.250375] Yama: becoming mindful.
[    0.250391] AppArmor: AppArmor initialized
[    0.254158] Dentry cache hash table entries: 4194304 (order: 13, 33554432 bytes)
[    0.256035] Inode-cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[    0.256101] Mount-cache hash table entries: 65536 (order: 7, 524288 bytes)
[    0.256170] Mountpoint-cache hash table entries: 65536 (order: 7, 524288 bytes)
[    0.256378] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[    0.256379] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[    0.256384] mce: CPU supports 10 MCE banks
[    0.256404] mce: CPU0: Thermal monitoring enabled (TM1)
[    0.256425] process: using mwait in idle threads
[    0.256428] Last level iTLB entries: 4KB 128, 2MB 8, 4MB 8
[    0.256429] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0, 1GB 4
[    0.256430] Spectre V2 : Mitigation: Full generic retpoline
[    0.256431] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[    0.256431] Spectre V2 : Enabling Restricted Speculation for firmware calls
[    0.256437] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier
[    0.256438] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl and seccomp
[    0.256695] Freeing SMP alternatives memory: 36K
[    0.259089] TSC deadline timer enabled
[    0.259094] smpboot: CPU0: Intel(R) Core(TM) i5-7440HQ CPU @ 2.80GHz (family: 0x6, model: 0x9e, stepping: 0x9)
[    0.259162] mce: [Hardware Error]: Machine check events logged
[    0.259163] mce: [Hardware Error]: CPU 0: Machine Check: 0 Bank 6: ee2000000040110a
[    0.259167] mce: [Hardware Error]: TSC 0 ADDR fef1cf00 MISC 3880008086 
[    0.259170] mce: [Hardware Error]: PROCESSOR 0:906e9 TIME 1562035643 SOCKET 0 APIC 0 microcode 9a
[    0.259173] mce: [Hardware Error]: Machine check events logged
[    0.259174] mce: [Hardware Error]: CPU 0: Machine Check: 0 Bank 7: ee2000000040110a
[    0.259176] mce: [Hardware Error]: TSC 0 ADDR fef200c0 MISC 3880008086 
[    0.259178] mce: [Hardware Error]: PROCESSOR 0:906e9 TIME 1562035643 SOCKET 0 APIC 0 microcode 9a
[    0.259181] mce: [Hardware Error]: CPU 0: Machine Check: 0 Bank 8: ee2000000040110a
[    0.259182] mce: [Hardware Error]: TSC 0 ADDR fef1ff40 MISC 7880008086 
[    0.259185] mce: [Hardware Error]: PROCESSOR 0:906e9 TIME 1562035643 SOCKET 0 APIC 0 microcode 9a
[    0.259187] mce: [Hardware Error]: CPU 0: Machine Check: 0 Bank 9: ee2000000040110a
[    0.259189] mce: [Hardware Error]: TSC 0 ADDR fef1cec0 MISC 43880008086 
[    0.259191] mce: [Hardware Error]: PROCESSOR 0:906e9 TIME 1562035643 SOCKET 0 APIC 0 microcode 9a
[    0.259226] Performance Events: PEBS fmt3+, Skylake events, 32-deep LBR, full-width counters, Intel PMU driver.
[    0.259259] ... version:                4
[    0.259260] ... bit width:              48
[    0.259260] ... generic registers:      8
[    0.259261] ... value mask:             0000ffffffffffff
[    0.259261] ... max period:             00007fffffffffff
[    0.259262] ... fixed-purpose events:   3
[    0.259262] ... event mask:             00000007000000ff
[    0.259299] rcu: Hierarchical SRCU implementation.
[    0.259922] random: crng done (trusting CPU's manufacturer)
[    0.260208] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[    0.260252] smp: Bringing up secondary CPUs ...
[    0.260329] x86: Booting SMP configuration:
[    0.260330] .... node  #0, CPUs:      #1 #2 #3
[    0.265440] smp: Brought up 1 node, 4 CPUs
[    0.265440] smpboot: Max logical packages: 1
[    0.265440] smpboot: Total of 4 processors activated (22464.00 BogoMIPS)
[    0.269378] devtmpfs: initialized
[    0.269394] x86/mm: Memory block size: 128MB
[    0.270716] PM: Registering ACPI NVS region [mem 0xba646000-0xba646fff] (4096 bytes)
[    0.270716] PM: Registering ACPI NVS region [mem 0xca709000-0xcaff3fff] (9351168 bytes)
[    0.270716] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.270716] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.270716] pinctrl core: initialized pinctrl subsystem
[    0.270716] RTC time: 02:47:23, date: 2019-07-02
[    0.270716] NET: Registered protocol family 16
[    0.270716] audit: initializing netlink subsys (disabled)
[    0.270716] audit: type=2000 audit(1562035643.056:1): state=initialized audit_enabled=0 res=1
[    0.270716] EISA bus registered
[    0.270716] cpuidle: using governor ladder
[    0.270716] cpuidle: using governor menu
[    0.270716] KVM setup pv remote TLB flush
[    0.270716] ACPI: bus type PCI registered
[    0.270716] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.270716] PCI: MMCONFIG for domain 0000 [bus 00-7f] at [mem 0xf0000000-0xf7ffffff] (base 0xf0000000)
[    0.270716] PCI: MMCONFIG at [mem 0xf0000000-0xf7ffffff] reserved in E820
[    0.270716] PCI: Using configuration type 1 for base access
[    0.270716] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.270716] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.270716] ACPI: Added _OSI(Module Device)
[    0.270716] ACPI: Added _OSI(Processor Device)
[    0.270716] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.270716] ACPI: Added _OSI(Processor Aggregator Device)
[    0.270716] ACPI: Added _OSI(Linux-Dell-Video)
[    0.270716] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[    0.270716] ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics)
[    0.324752] ACPI: 9 ACPI AML tables successfully acquired and loaded
[    0.330022] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[    0.341706] ACPI: Dynamic OEM Table Load:
[    0.341713] ACPI: SSDT 0xFFFF931199C17000 000651 (v02 PmRef  Cpu0Ist  00003000 INTL 20160422)
[    0.342405] ACPI: \_PR_.CPU0: _OSC native thermal LVT Acked
[    0.344098] ACPI: Dynamic OEM Table Load:
[    0.344104] ACPI: SSDT 0xFFFF931196395000 00065C (v02 PmRef  ApIst    00003000 INTL 20160422)
[    0.346854] ACPI: EC: EC started
[    0.346855] ACPI: EC: interrupt blocked
[    0.352258] ACPI: \_SB_.PCI0.LPCB.ECDV: Used as first EC
[    0.352260] ACPI: \_SB_.PCI0.LPCB.ECDV: GPE=0x6e, EC_CMD/EC_SC=0x934, EC_DATA=0x930
[    0.352261] ACPI: \_SB_.PCI0.LPCB.ECDV: Used as boot DSDT EC to handle transactions
[    0.352261] ACPI: Interpreter enabled
[    0.352311] ACPI: (supports S0 S3 S4 S5)
[    0.352312] ACPI: Using IOAPIC for interrupt routing
[    0.352358] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.353174] ACPI: Enabled 7 GPEs in block 00 to 7F
[    0.355974] ACPI: Power Resource [PG00] (on)
[    0.356613] ACPI: Power Resource [PG01] (on)
[    0.357227] ACPI: Power Resource [PG02] (on)
[    0.359448] ACPI: Power Resource [WRST] (on)
[    0.359921] ACPI: Power Resource [WRST] (on)
[    0.360393] ACPI: Power Resource [WRST] (on)
[    0.360867] ACPI: Power Resource [WRST] (on)
[    0.361340] ACPI: Power Resource [WRST] (on)
[    0.361824] ACPI: Power Resource [WRST] (on)
[    0.362845] ACPI: Power Resource [WRST] (on)
[    0.363319] ACPI: Power Resource [WRST] (on)
[    0.363787] ACPI: Power Resource [WRST] (on)
[    0.364260] ACPI: Power Resource [WRST] (on)
[    0.364729] ACPI: Power Resource [WRST] (on)
[    0.365199] ACPI: Power Resource [WRST] (on)
[    0.365672] ACPI: Power Resource [WRST] (on)
[    0.366141] ACPI: Power Resource [WRST] (on)
[    0.366609] ACPI: Power Resource [WRST] (on)
[    0.367079] ACPI: Power Resource [WRST] (on)
[    0.367555] ACPI: Power Resource [WRST] (on)
[    0.369352] ACPI: Power Resource [WRST] (on)
[    0.369823] ACPI: Power Resource [WRST] (on)
[    0.370291] ACPI: Power Resource [WRST] (on)
[    0.390954] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7e])
[    0.390961] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.393017] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug SHPCHotplug PME AER PCIeCapability LTR]
[    0.394016] PCI host bridge to bus 0000:00
[    0.394018] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.394019] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.394021] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.394022] pci_bus 0000:00: root bus resource [mem 0xcf800000-0xefffffff window]
[    0.394022] pci_bus 0000:00: root bus resource [mem 0xfd000000-0xfe7fffff window]
[    0.394024] pci_bus 0000:00: root bus resource [bus 00-7e]
[    0.394030] pci 0000:00:00.0: [8086:5910] type 00 class 0x060000
[    0.394180] pci 0000:00:02.0: [8086:591b] type 00 class 0x030000
[    0.394191] pci 0000:00:02.0: reg 0x10: [mem 0xee000000-0xeeffffff 64bit]
[    0.394197] pci 0000:00:02.0: reg 0x18: [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.394201] pci 0000:00:02.0: reg 0x20: [io  0xf000-0xf03f]
[    0.394217] pci 0000:00:02.0: BAR 2: assigned to efifb
[    0.394375] pci 0000:00:04.0: [8086:1903] type 00 class 0x118000
[    0.394387] pci 0000:00:04.0: reg 0x10: [mem 0xef240000-0xef247fff 64bit]
[    0.394633] pci 0000:00:14.0: [8086:a12f] type 00 class 0x0c0330
[    0.394654] pci 0000:00:14.0: reg 0x10: [mem 0xef230000-0xef23ffff 64bit]
[    0.394720] pci 0000:00:14.0: PME# supported from D3hot D3cold
[    0.394982] pci 0000:00:14.2: [8086:a131] type 00 class 0x118000
[    0.395002] pci 0000:00:14.2: reg 0x10: [mem 0xef258000-0xef258fff 64bit]
[    0.395279] pci 0000:00:15.0: [8086:a160] type 00 class 0x118000
[    0.395517] pci 0000:00:15.0: reg 0x10: [mem 0xef257000-0xef257fff 64bit]
[    0.396540] pci 0000:00:15.1: [8086:a161] type 00 class 0x118000
[    0.396802] pci 0000:00:15.1: reg 0x10: [mem 0xef256000-0xef256fff 64bit]
[    0.397754] pci 0000:00:16.0: [8086:a13a] type 00 class 0x078000
[    0.397778] pci 0000:00:16.0: reg 0x10: [mem 0xef255000-0xef255fff 64bit]
[    0.397843] pci 0000:00:16.0: PME# supported from D3hot
[    0.398042] pci 0000:00:17.0: [8086:2822] type 00 class 0x010400
[    0.398058] pci 0000:00:17.0: reg 0x10: [mem 0xef250000-0xef251fff]
[    0.398065] pci 0000:00:17.0: reg 0x14: [mem 0xef254000-0xef2540ff]
[    0.398072] pci 0000:00:17.0: reg 0x18: [io  0xf090-0xf097]
[    0.398079] pci 0000:00:17.0: reg 0x1c: [io  0xf080-0xf083]
[    0.398085] pci 0000:00:17.0: reg 0x20: [io  0xf060-0xf07f]
[    0.398092] pci 0000:00:17.0: reg 0x24: [mem 0xef253000-0xef2537ff]
[    0.398132] pci 0000:00:17.0: PME# supported from D3hot
[    0.398318] pci 0000:00:1c.0: [8086:a111] type 01 class 0x060400
[    0.398390] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.398610] pci 0000:00:1c.2: [8086:a112] type 01 class 0x060400
[    0.398681] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[    0.398900] pci 0000:00:1c.4: [8086:a114] type 01 class 0x060400
[    0.399065] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[    0.399297] pci 0000:00:1f.0: [8086:a154] type 00 class 0x060100
[    0.399532] pci 0000:00:1f.2: [8086:a121] type 00 class 0x058000
[    0.399548] pci 0000:00:1f.2: reg 0x10: [mem 0xef24c000-0xef24ffff]
[    0.399764] pci 0000:00:1f.3: [8086:a171] type 00 class 0x040300
[    0.399792] pci 0000:00:1f.3: reg 0x10: [mem 0xef248000-0xef24bfff 64bit]
[    0.399823] pci 0000:00:1f.3: reg 0x20: [mem 0xef220000-0xef22ffff 64bit]
[    0.399873] pci 0000:00:1f.3: PME# supported from D3hot D3cold
[    0.400136] pci 0000:00:1f.4: [8086:a123] type 00 class 0x0c0500
[    0.400197] pci 0000:00:1f.4: reg 0x10: [mem 0xef252000-0xef2520ff 64bit]
[    0.400268] pci 0000:00:1f.4: reg 0x20: [io  0xf040-0xf05f]
[    0.400512] pci 0000:00:1f.6: [8086:15e3] type 00 class 0x020000
[    0.400540] pci 0000:00:1f.6: reg 0x10: [mem 0xef200000-0xef21ffff]
[    0.400650] pci 0000:00:1f.6: PME# supported from D0 D3hot D3cold
[    0.401250] pci 0000:01:00.0: [8086:24fd] type 00 class 0x028000
[    0.401343] pci 0000:01:00.0: reg 0x10: [mem 0xef100000-0xef101fff 64bit]
[    0.401834] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    0.402557] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    0.402561] pci 0000:00:1c.0:   bridge window [mem 0xef100000-0xef1fffff]
[    0.402675] pci 0000:02:00.0: [10ec:525a] type 00 class 0xff0000
[    0.402707] pci 0000:02:00.0: reg 0x14: [mem 0xef000000-0xef000fff]
[    0.402814] pci 0000:02:00.0: supports D1 D2
[    0.402815] pci 0000:02:00.0: PME# supported from D1 D2 D3hot D3cold
[    0.403004] pci 0000:00:1c.2: PCI bridge to [bus 02]
[    0.403008] pci 0000:00:1c.2:   bridge window [mem 0xef000000-0xef0fffff]
[    0.403107] pci 0000:00:1c.4: PCI bridge to [bus 03]
[    0.408373] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.408445] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *10 11 12 14 15)
[    0.408514] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.408582] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.408651] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.408718] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.408788] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.408857] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.411588] ACPI: EC: interrupt unblocked
[    0.411588] ACPI: EC: event unblocked
[    0.411590] ACPI: \_SB_.PCI0.LPCB.ECDV: GPE=0x6e, EC_CMD/EC_SC=0x934, EC_DATA=0x930
[    0.411590] ACPI: \_SB_.PCI0.LPCB.ECDV: Used as boot DSDT EC to handle transactions and events
[    0.411590] SCSI subsystem initialized
[    0.411590] libata version 3.00 loaded.
[    0.411590] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[    0.411590] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[    0.411590] pci 0000:00:02.0: vgaarb: bridge control possible
[    0.411590] vgaarb: loaded
[    0.411590] ACPI: bus type USB registered
[    0.411590] usbcore: registered new interface driver usbfs
[    0.411590] usbcore: registered new interface driver hub
[    0.411590] usbcore: registered new device driver usb
[    0.411590] pps_core: LinuxPPS API ver. 1 registered
[    0.411590] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.411590] PTP clock support registered
[    0.411590] EDAC MC: Ver: 3.0.0
[    0.411590] Registered efivars operations
[    0.417455] PCI: Using ACPI for IRQ routing
[    0.430591] PCI: pci_cache_line_size set to 64 bytes
[    0.431236] e820: reserve RAM buffer [mem 0x00058000-0x0005ffff]
[    0.431237] e820: reserve RAM buffer [mem 0x0009f000-0x0009ffff]
[    0.431238] e820: reserve RAM buffer [mem 0xba646000-0xbbffffff]
[    0.431239] e820: reserve RAM buffer [mem 0xca33a000-0xcbffffff]
[    0.431240] e820: reserve RAM buffer [mem 0xcb600000-0xcbffffff]
[    0.431241] e820: reserve RAM buffer [mem 0x52e800000-0x52fffffff]
[    0.431322] NetLabel: Initializing
[    0.431323] NetLabel:  domain hash size = 128
[    0.431323] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.431337] NetLabel:  unlabeled traffic allowed by default
[    0.433906] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[    0.433910] hpet0: 8 comparators, 64-bit 24.000000 MHz counter
[    0.437360] clocksource: Switched to clocksource tsc-early
[    0.448023] VFS: Disk quotas dquot_6.6.0
[    0.448035] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.448129] AppArmor: AppArmor Filesystem Enabled
[    0.448153] pnp: PnP ACPI init
[    0.448438] system 00:00: [io  0x0680-0x069f] has been reserved
[    0.448439] system 00:00: [io  0xffff] has been reserved
[    0.448441] system 00:00: [io  0xffff] has been reserved
[    0.448442] system 00:00: [io  0xffff] has been reserved
[    0.448443] system 00:00: [io  0x1800-0x18fe] has been reserved
[    0.448444] system 00:00: [io  0x164e-0x164f] has been reserved
[    0.448448] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.448564] system 00:01: [io  0x0800-0x087f] has been reserved
[    0.448567] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.448587] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.448629] system 00:03: [io  0x1854-0x1857] has been reserved
[    0.448632] system 00:03: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[    0.448768] pnp 00:04: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.449075] system 00:05: [mem 0xfed10000-0xfed17fff] has been reserved
[    0.449076] system 00:05: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.449077] system 00:05: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.449078] system 00:05: [mem 0xf0000000-0xf7ffffff] has been reserved
[    0.449080] system 00:05: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.449081] system 00:05: [mem 0xfed90000-0xfed93fff] could not be reserved
[    0.449082] system 00:05: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.449083] system 00:05: [mem 0xff000000-0xffffffff] has been reserved
[    0.449084] system 00:05: [mem 0xfee00000-0xfeefffff] could not be reserved
[    0.449086] system 00:05: [mem 0xeffe0000-0xefffffff] has been reserved
[    0.449089] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.449136] system 00:06: [mem 0xfd000000-0xfdabffff] has been reserved
[    0.449137] system 00:06: [mem 0xfdad0000-0xfdadffff] has been reserved
[    0.449138] system 00:06: [mem 0xfdb00000-0xfdffffff] has been reserved
[    0.449140] system 00:06: [mem 0xfe000000-0xfe01ffff] could not be reserved
[    0.449141] system 00:06: [mem 0xfe036000-0xfe03bfff] has been reserved
[    0.449142] system 00:06: [mem 0xfe03d000-0xfe3fffff] has been reserved
[    0.449143] system 00:06: [mem 0xfe410000-0xfe7fffff] has been reserved
[    0.449146] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.449554] system 00:07: [io  0xff00-0xfffe] has been reserved
[    0.449557] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.451207] system 00:08: [mem 0xfdaf0000-0xfdafffff] has been reserved
[    0.451209] system 00:08: [mem 0xfdae0000-0xfdaeffff] has been reserved
[    0.451210] system 00:08: [mem 0xfdac0000-0xfdacffff] has been reserved
[    0.451213] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.455028] pnp: PnP ACPI: found 9 devices
[    0.460674] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.460699] pci 0000:00:1c.4: bridge window [io  0x1000-0x0fff] to [bus 03] add_size 1000
[    0.460700] pci 0000:00:1c.4: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 03] add_size 200000 add_align 100000
[    0.460702] pci 0000:00:1c.4: bridge window [mem 0x00100000-0x000fffff] to [bus 03] add_size 200000 add_align 100000
[    0.460707] pci 0000:00:1c.4: BAR 14: assigned [mem 0xcf800000-0xcf9fffff]
[    0.460711] pci 0000:00:1c.4: BAR 15: assigned [mem 0xcfa00000-0xcfbfffff 64bit pref]
[    0.460713] pci 0000:00:1c.4: BAR 13: assigned [io  0x2000-0x2fff]
[    0.460716] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    0.460719] pci 0000:00:1c.0:   bridge window [mem 0xef100000-0xef1fffff]
[    0.460725] pci 0000:00:1c.2: PCI bridge to [bus 02]
[    0.460728] pci 0000:00:1c.2:   bridge window [mem 0xef000000-0xef0fffff]
[    0.460733] pci 0000:00:1c.4: PCI bridge to [bus 03]
[    0.460736] pci 0000:00:1c.4:   bridge window [io  0x2000-0x2fff]
[    0.460739] pci 0000:00:1c.4:   bridge window [mem 0xcf800000-0xcf9fffff]
[    0.460741] pci 0000:00:1c.4:   bridge window [mem 0xcfa00000-0xcfbfffff 64bit pref]
[    0.460747] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.460748] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.460749] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.460750] pci_bus 0000:00: resource 7 [mem 0xcf800000-0xefffffff window]
[    0.460751] pci_bus 0000:00: resource 8 [mem 0xfd000000-0xfe7fffff window]
[    0.460752] pci_bus 0000:01: resource 1 [mem 0xef100000-0xef1fffff]
[    0.460753] pci_bus 0000:02: resource 1 [mem 0xef000000-0xef0fffff]
[    0.460754] pci_bus 0000:03: resource 0 [io  0x2000-0x2fff]
[    0.460755] pci_bus 0000:03: resource 1 [mem 0xcf800000-0xcf9fffff]
[    0.460755] pci_bus 0000:03: resource 2 [mem 0xcfa00000-0xcfbfffff 64bit pref]
[    0.460934] NET: Registered protocol family 2
[    0.461058] tcp_listen_portaddr_hash hash table entries: 16384 (order: 6, 262144 bytes)
[    0.461153] TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.461434] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.461524] TCP: Hash tables configured (established 262144 bind 65536)
[    0.461560] UDP hash table entries: 16384 (order: 7, 524288 bytes)
[    0.461638] UDP-Lite hash table entries: 16384 (order: 7, 524288 bytes)
[    0.461741] NET: Registered protocol family 1
[    0.461745] NET: Registered protocol family 44
[    0.461753] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.463063] PCI: CLS 0 bytes, default 64
[    0.463098] Unpacking initramfs...
[    8.486095] Freeing initrd memory: 41328K
[    8.486159] DMAR: ACPI device "device:71" under DMAR at fed91000 as 00:15.0
[    8.486162] DMAR: ACPI device "device:72" under DMAR at fed91000 as 00:15.1
[    8.501377] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    8.501378] software IO TLB: mapped [mem 0xb4a26000-0xb8a26000] (64MB)
[    8.501502] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2879c5f06f2, max_idle_ns: 440795220049 ns
[    8.501512] clocksource: Switched to clocksource tsc
[    8.501578] check: Scanning for low memory corruption every 60 seconds
[    8.503208] Initialise system trusted keyrings
[    8.503216] Key type blacklist registered
[    8.503241] workingset: timestamp_bits=36 max_order=23 bucket_order=0
[    8.504443] zbud: loaded
[    8.504843] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    8.505013] fuse init (API version 7.28)
[    8.539481] Key type asymmetric registered
[    8.539482] Asymmetric key parser 'x509' registered
[    8.539489] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[    8.539515] io scheduler mq-deadline registered
[    8.539863] pcieport 0000:00:1c.0: Signaling PME with IRQ 122
[    8.539911] aer 0000:00:1c.0:pcie002: AER enabled with IRQ 122
[    8.540110] pcieport 0000:00:1c.2: Signaling PME with IRQ 123
[    8.540150] aer 0000:00:1c.2:pcie002: AER enabled with IRQ 123
[    8.540353] pcieport 0000:00:1c.4: Signaling PME with IRQ 124
[    8.540404] aer 0000:00:1c.4:pcie002: AER enabled with IRQ 124
[    8.540422] pciehp 0000:00:1c.4:pcie004: Slot #8 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Interlock- NoCompl+ LLActRep+
[    8.540512] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    8.540568] efifb: probing for efifb
[    8.540581] efifb: framebuffer at 0xd0000000, using 8128k, total 8128k
[    8.540582] efifb: mode is 1920x1080x32, linelength=7680, pages=1
[    8.540582] efifb: scrolling: redraw
[    8.540583] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    8.544496] Console: switching to colour frame buffer device 240x67
[    8.548324] fb0: EFI VGA frame buffer device
[    8.548331] intel_idle: MWAIT substates: 0x11142120
[    8.548332] intel_idle: v0.4.1 model 0x9E
[    8.548569] intel_idle: lapic_timer_reliable_states 0xffffffff
[    8.549663] ACPI: AC Adapter [AC] (on-line)
[    8.549735] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[    8.549746] ACPI: Lid Switch [LID0]
[    8.549772] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[    8.549778] ACPI: Power Button [PBTN]
[    8.549801] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[    8.549808] ACPI: Sleep Button [SBTN]
[    8.549832] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    8.549837] ACPI: Power Button [PWRF]
[    8.551920] thermal LNXTHERM:00: registered as thermal_zone0
[    8.551921] ACPI: Thermal Zone [THM] (25 C)
[    8.552089] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    8.558357] Linux agpgart interface v0.103
[    8.562889] loop: module loaded
[    8.563321] libphy: Fixed MDIO Bus: probed
[    8.563322] tun: Universal TUN/TAP device driver, 1.6
[    8.563379] PPP generic driver version 2.4.2
[    8.563662] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    8.563665] ehci-pci: EHCI PCI platform driver
[    8.563673] ehci-platform: EHCI generic platform driver
[    8.563914] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    8.563916] ohci-pci: OHCI PCI platform driver
[    8.563922] ohci-platform: OHCI generic platform driver
[    8.563929] uhci_hcd: USB Universal Host Controller Interface driver
[    8.564799] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    8.564806] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[    8.566309] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000000001109810
[    8.566313] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[    8.566482] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.00
[    8.566562] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    8.566563] usb usb1: Product: xHCI Host Controller
[    8.566564] usb usb1: Manufacturer: Linux 5.0.0-13-generic xhci-hcd
[    8.566638] usb usb1: SerialNumber: 0000:00:14.0
[    8.567059] hub 1-0:1.0: USB hub found
[    8.567074] hub 1-0:1.0: 16 ports detected
[    8.586971] battery: ACPI: Battery Slot [BAT0] (battery present)
[    8.587476] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    8.587479] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[    8.587482] xhci_hcd 0000:00:14.0: Host supports USB 3.0  SuperSpeed
[    8.587521] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.00
[    8.587522] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    8.587523] usb usb2: Product: xHCI Host Controller
[    8.587524] usb usb2: Manufacturer: Linux 5.0.0-13-generic xhci-hcd
[    8.587525] usb usb2: SerialNumber: 0000:00:14.0
[    8.587636] hub 2-0:1.0: USB hub found
[    8.587648] hub 2-0:1.0: 10 ports detected
[    8.588461] usb: port power management may be unreliable
[    8.589061] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[    8.589062] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[    8.589421] i8042: Warning: Keylock active
[    8.589667] serio: i8042 KBD port at 0x60,0x64 irq 1
[    8.589810] mousedev: PS/2 mouse device common for all mice
[    8.590154] rtc_cmos 00:02: RTC can wake from S4
[    8.590711] rtc_cmos 00:02: registered as rtc0
[    8.590726] rtc_cmos 00:02: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    8.590732] i2c /dev entries driver
[    8.590803] device-mapper: uevent: version 1.0.3
[    8.590867] device-mapper: ioctl: 4.39.0-ioctl (2018-04-03) initialised: dm-devel@redhat.com
[    8.590899] platform eisa.0: Probing EISA bus 0
[    8.590900] platform eisa.0: EISA: Cannot allocate resource for mainboard
[    8.590902] platform eisa.0: Cannot allocate resource for EISA slot 1
[    8.590902] platform eisa.0: Cannot allocate resource for EISA slot 2
[    8.590903] platform eisa.0: Cannot allocate resource for EISA slot 3
[    8.590904] platform eisa.0: Cannot allocate resource for EISA slot 4
[    8.590905] platform eisa.0: Cannot allocate resource for EISA slot 5
[    8.590906] platform eisa.0: Cannot allocate resource for EISA slot 6
[    8.590907] platform eisa.0: Cannot allocate resource for EISA slot 7
[    8.590908] platform eisa.0: Cannot allocate resource for EISA slot 8
[    8.590908] platform eisa.0: EISA: Detected 0 cards
[    8.590911] intel_pstate: Intel P-state driver initializing
[    8.590928] intel_pstate: Disabling energy efficiency optimization
[    8.591107] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[    8.591204] intel_pstate: HWP enabled
[    8.591222] ledtrig-cpu: registered to indicate activity on CPUs
[    8.591224] EFI Variables Facility v0.08 2004-May-17
[    8.597370] resource sanity check: requesting [mem 0xfdffe800-0xfe0007ff], which spans more than pnp 00:06 [mem 0xfdb00000-0xfdffffff]
[    8.597373] caller pmc_core_probe+0x8c/0x284 mapping multiple BARs
[    8.597379] intel_pmc_core:  initialized
[    8.597592] NET: Registered protocol family 10
[    8.601855] Segment Routing with IPv6
[    8.601868] NET: Registered protocol family 17
[    8.601958] Key type dns_resolver registered
[    8.602379] RAS: Correctable Errors collector initialized.
[    8.602399] microcode: sig=0x906e9, pf=0x20, revision=0x9a
[    8.602548] microcode: Microcode Update Driver: v2.2.
[    8.602555] sched_clock: Marking stable (8606091189, -3547653)->(8606690016, -4146480)
[    8.602925] registered taskstats version 1
[    8.602933] Loading compiled-in X.509 certificates
[    8.604096] Loaded X.509 cert 'Build time autogenerated kernel key: a91cf5411f714b0dcaaa6539e6139a929efd4f6a'
[    8.604332] Loaded UEFI:db cert 'Dell Inc. UEFI DB: 5ddb772dc880660055ba0bc131886bb630a639e7' linked to secondary sys keyring
[    8.604358] Loaded UEFI:db cert 'Microsoft Corporation UEFI CA 2011: 13adbf4309bd82709c8cd54f316ed522988a1bd4' linked to secondary sys keyring
[    8.604369] Loaded UEFI:db cert 'Microsoft Windows Production PCA 2011: a92902398e16c49778cd90f99e4f9ae17c55af53' linked to secondary sys keyring
[    8.604465] Couldn't get size: 0x800000000000000e
[    8.604479] MODSIGN: Couldn't get UEFI MokListRT
[    8.604896] zswap: loaded using pool lzo/zbud
[    8.608844] Key type big_key registered
[    8.608847] Key type trusted registered
[    8.610976] Key type encrypted registered
[    8.610979] AppArmor: AppArmor sha1 policy hashing enabled
[    8.611613] ima: No TPM chip found, activating TPM-bypass!
[    8.611617] ima: Allocated hash algorithm: sha1
[    8.611620] No architecture policies found
[    8.611625] evm: Initialising EVM extended attributes:
[    8.611626] evm: security.selinux
[    8.611626] evm: security.SMACK64
[    8.611627] evm: security.SMACK64EXEC
[    8.611627] evm: security.SMACK64TRANSMUTE
[    8.611627] evm: security.SMACK64MMAP
[    8.611627] evm: security.apparmor
[    8.611628] evm: security.ima
[    8.611628] evm: security.capability
[    8.611628] evm: HMAC attrs: 0x1
[    8.612577]   Magic number: 11:599:762
[    8.612581] atkbd serio0: hash matches
[    8.612768] rtc_cmos 00:02: setting system clock to 2019-07-02T02:47:32 UTC (1562035652)
[    8.613822] Freeing unused decrypted memory: 2040K
[    8.614159] Freeing unused kernel image memory: 2576K
[    8.637411] Write protecting the kernel read-only data: 22528k
[    8.637968] Freeing unused kernel image memory: 2016K
[    8.638181] Freeing unused kernel image memory: 1852K
[    8.644502] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    8.644502] x86/mm: Checking user space page tables
[    8.650503] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    8.650504] Run /init as init process
[    8.705408] hidraw: raw HID events driver (C) Jiri Kosina
[    8.706050] wmi_bus wmi_bus-PNP0C14:01: WQBC data block query control method not found
[    8.711554] intel-lpss 0000:00:15.0: enabling device (0000 -> 0002)
[    8.713893] rtsx_pci 0000:02:00.0: enabling device (0000 -> 0002)
[    8.714146] ahci 0000:00:17.0: version 3.0
[    8.714244] ahci 0000:00:17.0: controller can't do SNTF, turning off CAP_SNTF
[    8.714312] ahci 0000:00:17.0: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x4 impl RAID mode
[    8.714313] ahci 0000:00:17.0: flags: 64bit ncq pm led clo only pio slum part ems deso sadm sds apst 
[    8.716219] i801_smbus 0000:00:1f.4: SPD Write Disable is set
[    8.716249] i801_smbus 0000:00:1f.4: SMBus using PCI interrupt
[    8.718056] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    8.718056] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    8.718972] scsi host0: ahci
[    8.719313] e1000e 0000:00:1f.6: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[    8.719411] scsi host1: ahci
[    8.721417] scsi host2: ahci
[    8.721458] ata1: DUMMY
[    8.721459] ata2: DUMMY
[    8.721460] ata3: SATA max UDMA/133 abar m2048@0xef253000 port 0xef253200 irq 127
[    8.731720] intel-lpss 0000:00:15.1: enabling device (0000 -> 0002)
[    8.738258] i2c_hid i2c-DLL07A9:01: i2c-DLL07A9:01 supply vdd not found, using dummy regulator
[    8.738265] i2c_hid i2c-DLL07A9:01: Linked as a consumer to regulator.0
[    8.738266] i2c_hid i2c-DLL07A9:01: i2c-DLL07A9:01 supply vddl not found, using dummy regulator
[    8.757098] VFIO - User Level meta-driver version: 0.3
[    8.776385] checking generic (d0000000 7f0000) vs hw (d0000000 10000000)
[    8.776386] fb0: switching to inteldrmfb from EFI VGA
[    8.776401] Console: switching to colour dummy device 80x25
[    8.776539] [drm] Replacing VGA console driver
[    8.777263] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    8.777264] [drm] Driver supports precise vblank timestamp query.
[    8.777689] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem
[    8.778006] [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4)
[    8.796695] [drm] Initialized i915 1.6.0 20181204 for 0000:00:02.0 on minor 0
[    8.799111] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[    8.799913] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input5
[    8.924177] e1000e 0000:00:1f.6 0000:00:1f.6 (uninitialized): registered PHC clock
[    8.925499] usb 2-1: new SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[    8.993690] e1000e 0000:00:1f.6 eth0: (PCI Express:2.5GT/s:Width x1) d4:81:d7:b5:5b:e8
[    8.993691] e1000e 0000:00:1f.6 eth0: Intel(R) PRO/1000 Network Connection
[    8.993753] e1000e 0000:00:1f.6 eth0: MAC: 12, PHY: 12, PBA No: FFFFFF-0FF
[    8.994594] e1000e 0000:00:1f.6 enp0s31f6: renamed from eth0
[    9.009184] input: DualPoint Stick as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-2/i2c-DLL07A9:01/0018:044E:120B.0001/input/input7
[    9.009281] input: DLL07A9:01 044E:120B as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-2/i2c-DLL07A9:01/0018:044E:120B.0001/input/input6
[    9.009320] hid-alps 0018:044E:120B.0001: input,hidraw0: I2C HID v1.00 Mouse [DLL07A9:01 044E:120B] on i2c-DLL07A9:01
[    9.028076] fbcon: inteldrmfb (fb0) is primary device
[    9.036662] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    9.040871] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[    9.040872] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[    9.040889] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[    9.042602] ata3.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[    9.095724] ata3.00: ATA-8: TOSHIBA MQ01ACF050, AV002D, max UDMA/100
[    9.095725] ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[    9.097799] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[    9.097800] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[    9.097801] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[    9.098247] ata3.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[    9.099816] ata3.00: configured for UDMA/100
[    9.100072] scsi 2:0:0:0: Direct-Access     ATA      TOSHIBA MQ01ACF0 2D   PQ: 0 ANSI: 5
[    9.100366] sd 2:0:0:0: Attached scsi generic sg0 type 0
[    9.100514] sd 2:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[    9.100515] sd 2:0:0:0: [sda] 4096-byte physical blocks
[    9.100544] sd 2:0:0:0: [sda] Write Protect is off
[    9.100545] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    9.100611] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    9.204709]  sda: sda1 < sda5 sda6 > sda3 sda4
[    9.205649] sd 2:0:0:0: [sda] Attached SCSI disk
[    9.529479] usb 2-1: New USB device found, idVendor=0951, idProduct=16ae, bcdDevice= 1.10
[    9.529480] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    9.529481] usb 2-1: Product: DT microDuo 3C
[    9.529481] usb 2-1: Manufacturer: Kingston
[    9.529482] usb 2-1: SerialNumber: 408D5CBEC94AE2C0E9202BDF
[    9.533114] usb-storage 2-1:1.0: USB Mass Storage device detected
[    9.533191] scsi host3: usb-storage 2-1:1.0
[    9.533229] usbcore: registered new interface driver usb-storage
[    9.533931] usbcore: registered new interface driver uas
[    9.653410] usb 1-3: new full-speed USB device number 2 using xhci_hcd
[    9.803842] usb 1-3: New USB device found, idVendor=2717, idProduct=5001, bcdDevice= 1.00
[    9.803843] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    9.803843] usb 1-3: Product: MI wireless mouse
[    9.803856] usb 1-3: Manufacturer: GTech
[    9.809117] input: GTech MI wireless mouse Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.0/0003:2717:5001.0002/input/input8
[    9.809183] input: GTech MI wireless mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.0/0003:2717:5001.0002/input/input9
[    9.809215] input: GTech MI wireless mouse Consumer Control as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.0/0003:2717:5001.0002/input/input10
[    9.865554] input: GTech MI wireless mouse System Control as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.0/0003:2717:5001.0002/input/input11
[    9.865851] hid-generic 0003:2717:5001.0002: input,hiddev0,hidraw1: USB HID v1.10 Mouse [GTech MI wireless mouse] on usb-0000:00:14.0-3/input0
[    9.865884] usbcore: registered new interface driver usbhid
[    9.865884] usbhid: USB HID core driver
[    9.929402] usb 1-6: new full-speed USB device number 3 using xhci_hcd
[   10.079021] usb 1-6: New USB device found, idVendor=8087, idProduct=0a2b, bcdDevice= 0.10
[   10.079034] usb 1-6: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[   10.131992] Console: switching to colour frame buffer device 240x67
[   10.150989] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[   10.205406] usb 1-11: new high-speed USB device number 4 using xhci_hcd
[   10.365958] usb 1-11: New USB device found, idVendor=1bcf, idProduct=2b96, bcdDevice=68.25
[   10.365971] usb 1-11: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[   10.365972] usb 1-11: Product: Integrated_Webcam_HD
[   10.365973] usb 1-11: Manufacturer: CNFGH19N0420178A3082
[   10.550436] scsi 3:0:0:0: Direct-Access     Kingston DT microDuo 3C   PMAP PQ: 0 ANSI: 6
[   10.550756] sd 3:0:0:0: Attached scsi generic sg1 type 0
[   10.551175] sd 3:0:0:0: [sdb] 242221056 512-byte logical blocks: (124 GB/116 GiB)
[   10.551579] sd 3:0:0:0: [sdb] Write Protect is off
[   10.551580] sd 3:0:0:0: [sdb] Mode Sense: 45 00 00 00
[   10.551859] sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   10.554207]  sdb: sdb1 sdb2
[   10.556076] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[   11.418420] EXT4-fs (sda3): INFO: recovery required on readonly filesystem
[   11.418421] EXT4-fs (sda3): write access will be enabled during recovery
[   17.168285] EXT4-fs (sda3): orphan cleanup on readonly fs
[   17.213061] EXT4-fs (sda3): 8 orphan inodes deleted
[   17.213062] EXT4-fs (sda3): recovery complete
[   17.494989] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[   17.650084] EXT4-fs (sda4): INFO: recovery required on readonly filesystem
[   17.650085] EXT4-fs (sda4): write access will be enabled during recovery
[   17.753172] EXT4-fs (sda4): recovery complete
[   17.771793] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
[   18.002021] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
[   18.072411] ISO 9660 Extensions: Microsoft Joliet Level 3
[   18.074167] ISO 9660 Extensions: RRIP_1991A
[   21.641605] systemd[1]: Inserted module 'autofs4'
[   21.667313] systemd[1]: systemd 240 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[   21.685485] systemd[1]: Detected architecture x86-64.
[   21.695342] systemd[1]: Set hostname to <kubuntu>.
[   21.695454] systemd[1]: Initializing machine ID from random generator.
[   21.769526] systemd[1]: /lib/systemd/system/spice-vdagentd.service:8: PIDFile= references path below legacy directory /var/run/, updating /var/run/spice-vdagentd/spice-vdagentd.pid → /run/spice-vdagentd/spice-vdagentd.pid; please update the unit file accordingly.
[   21.771121] systemd[1]: Reached target Remote File Systems.
[   21.771347] systemd[1]: Listening on Syslog Socket.
[   21.771375] systemd[1]: Listening on initctl Compatibility Named Pipe.
[   21.771379] systemd[1]: Reached target Swap.
[   21.771513] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[   21.841374] systemd-journald[1098]: Received request to flush runtime journal from PID 1
[   21.845935] lp: driver loaded but no devices found
[   21.854692] ppdev: user-space parallel port driver
[   22.396349] input: Intel HID events as /devices/platform/INT33D5:00/input/input13
[   22.396408] int3403 thermal: probe of INT3403:03 failed with error -22
[   22.396570] intel-hid INT33D5:00: platform supports 5 button array
[   22.396592] input: Intel HID 5 button array as /devices/platform/INT33D5:00/input/input14
[   22.418033] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.3)
[   22.439315] input: Dell WMI hotkeys as /devices/platform/PNP0C14:01/wmi_bus/wmi_bus-PNP0C14:01/9DBB5994-A997-11DA-B012-B622A1EF5492/input/input15
[   22.458690] proc_thermal 0000:00:04.0: enabling device (0000 -> 0002)
[   22.488850] proc_thermal 0000:00:04.0: Creating sysfs group for PROC_THERMAL_PCI
[   22.511937] RAPL PMU: API unit is 2^-32 Joules, 5 fixed counters, 655360 ms ovfl timer
[   22.511938] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
[   22.511939] RAPL PMU: hw unit of domain package 2^-14 Joules
[   22.511939] RAPL PMU: hw unit of domain dram 2^-14 Joules
[   22.511939] RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules
[   22.511940] RAPL PMU: hw unit of domain psys 2^-14 Joules
[   22.607110] mei_me 0000:00:16.0: enabling device (0000 -> 0002)
[   22.630689] idma64 idma64.0: Found Intel integrated DMA 64-bit
[   22.630832] idma64 idma64.1: Found Intel integrated DMA 64-bit
[   22.670966] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[   22.674737] cryptd: max_cpu_qlen set to 1000
[   22.679946] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[   22.715896] Bluetooth: Core ver 2.22
[   22.715915] NET: Registered protocol family 31
[   22.715915] Bluetooth: HCI device and connection manager initialized
[   22.715917] Bluetooth: HCI socket layer initialized
[   22.715919] Bluetooth: L2CAP socket layer initialized
[   22.715921] Bluetooth: SCO socket layer initialized
[   22.735929] dell_laptop: Using i8042 filter function for receiving events
[   22.760477] usbcore: registered new interface driver btusb
[   22.763319] Bluetooth: hci0: Bootloader revision 0.0 build 26 week 38 2015
[   22.764334] Bluetooth: hci0: Device revision is 16
[   22.764335] Bluetooth: hci0: Secure boot is enabled
[   22.764335] Bluetooth: hci0: OTP lock is enabled
[   22.764336] Bluetooth: hci0: API lock is enabled
[   22.764336] Bluetooth: hci0: Debug lock is disabled
[   22.764337] Bluetooth: hci0: Minimum firmware build 1 week 10 2014
[   22.775358] media: Linux media interface: v0.10
[   22.791667] AVX2 version of gcm_enc/dec engaged.
[   22.791668] AES CTR mode by8 optimization enabled
[   22.797368] Intel(R) Wireless WiFi driver for Linux
[   22.797369] Copyright(c) 2003- 2015 Intel Corporation
[   22.797685] iwlwifi 0000:01:00.0: enabling device (0000 -> 0002)
[   22.810940] videodev: Linux video capture interface: v2.00
[   22.837198] Bluetooth: hci0: Found device firmware: intel/ibt-12-16.sfi
[   22.913199] iwlwifi 0000:01:00.0: loaded firmware version 36.9f0a2d68.0 op_mode iwlmvm
[   22.923158] uvcvideo: Found UVC 1.00 device Integrated_Webcam_HD (1bcf:2b96)
[   22.944288] uvcvideo 1-11:1.0: Entity type for entity Extension 4 was not initialized!
[   22.944290] uvcvideo 1-11:1.0: Entity type for entity Extension 3 was not initialized!
[   22.944290] uvcvideo 1-11:1.0: Entity type for entity Processing 2 was not initialized!
[   22.944291] uvcvideo 1-11:1.0: Entity type for entity Camera 1 was not initialized!
[   22.944339] input: Integrated_Webcam_HD: Integrate as /devices/pci0000:00/0000:00:14.0/usb1/1-11/1-11:1.0/input/input16
[   22.944384] usbcore: registered new interface driver uvcvideo
[   22.944385] USB Video Class driver (1.1.1)
[   22.983229] iwlwifi 0000:01:00.0: Detected Intel(R) Dual Band Wireless AC 8265, REV=0x230
[   23.052832] iwlwifi 0000:01:00.0: base HW address: 00:28:f8:b9:89:8f
[   23.149827] intel_rapl: Found RAPL domain package
[   23.149828] intel_rapl: Found RAPL domain core
[   23.149829] intel_rapl: Found RAPL domain uncore
[   23.149830] intel_rapl: Found RAPL domain dram
[   23.150527] snd_hda_intel 0000:00:1f.3: Linked as a consumer to 0000:00:02.0
[   23.150554] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
[   23.253933] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC3246: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[   23.253934] snd_hda_codec_realtek hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   23.253935] snd_hda_codec_realtek hdaudioC0D0:    hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[   23.253936] snd_hda_codec_realtek hdaudioC0D0:    mono: mono_out=0x0
[   23.253936] snd_hda_codec_realtek hdaudioC0D0:    inputs:
[   23.253938] snd_hda_codec_realtek hdaudioC0D0:      Headset Mic=0x19
[   23.253938] snd_hda_codec_realtek hdaudioC0D0:      Headphone Mic=0x1a
[   23.253939] snd_hda_codec_realtek hdaudioC0D0:      Internal Mic=0x12
[   23.262086] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   23.262087] Bluetooth: BNEP filters: protocol multicast
[   23.262090] Bluetooth: BNEP socket layer initialized
[   23.288210] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs'
[   23.288398] thermal thermal_zone7: failed to read out thermal zone (-61)
[   23.317221] input: HDA Intel PCH Headphone Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input17
[   23.317265] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input18
[   23.317298] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input19
[   23.317331] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input20
[   23.317374] input: HDA Intel PCH HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input21
[   23.317408] input: HDA Intel PCH HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input22
[   23.405050] iwlwifi 0000:01:00.0 wlp1s0: renamed from wlan0
[   23.405077] audit: type=1400 audit(1562035667.287:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/snapd/snap-confine" pid=1432 comm="apparmor_parser"
[   23.405198] audit: type=1400 audit(1562035667.287:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/snapd/snap-confine//mount-namespace-capture-helper" pid=1432 comm="apparmor_parser"
[   24.415192] Bluetooth: hci0: Waiting for firmware download to complete
[   24.415304] Bluetooth: hci0: Firmware loaded in 1614969 usecs
[   24.415322] Bluetooth: hci0: Waiting for device to boot
[   24.427406] Bluetooth: hci0: Device booted in 11807 usecs
[   24.430620] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-12-16.ddc
[   24.433486] Bluetooth: hci0: Applying Intel DDC parameters completed
[   52.627371] Bluetooth: RFCOMM TTY layer initialized
[   52.627376] Bluetooth: RFCOMM socket layer initialized
[   52.627382] Bluetooth: RFCOMM ver 1.11
[  119.944449] wlp1s0: authenticate with 3c:0c:db:d9:1f:b0
[  119.953781] wlp1s0: send auth to 3c:0c:db:d9:1f:b0 (try 1/3)
[  119.962889] wlp1s0: authenticated
[  119.963189] iwlwifi 0000:01:00.0 wlp1s0: disabling HE/HT/VHT due to WEP/TKIP use
[  119.965466] wlp1s0: associate with 3c:0c:db:d9:1f:b0 (try 1/3)
[  119.971915] wlp1s0: RX AssocResp from 3c:0c:db:d9:1f:b0 (capab=0x411 status=0 aid=3)
[  119.983749] wlp1s0: associated
[  120.079126] IPv6: ADDRCONF(NETDEV_CHANGE): wlp1s0: link becomes ready
[ 3035.073214] PM: suspend entry (deep)
[ 3035.073215] PM: Syncing filesystems ... done.
[ 3035.076146] Freezing user space processes ... (elapsed 0.001 seconds) done.
[ 3035.077573] OOM killer disabled.
[ 3035.077574] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 3035.078724] printk: Suspending console(s) (use no_console_suspend to debug)
[ 3035.079423] wlp1s0: deauthenticating from 3c:0c:db:d9:1f:b0 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 3035.104712] sd 2:0:0:0: [sda] Synchronizing SCSI cache
[ 3035.104873] sd 2:0:0:0: [sda] Stopping disk
[ 3035.190965] e1000e: EEE TX LPI TIMER: 00000011
[ 3035.852744] ACPI: EC: interrupt blocked
[ 3035.892527] ACPI: Preparing to enter system sleep state S3
[ 3035.899959] ACPI: EC: event blocked
[ 3035.899959] ACPI: EC: EC stopped
[ 3035.899960] PM: Saving platform NVS memory
[ 3035.900053] Disabling non-boot CPUs ...
[ 3035.900439] IRQ 123: no longer affine to CPU1
[ 3035.900444] IRQ 131: no longer affine to CPU1
[ 3035.901462] smpboot: CPU 1 is now offline
[ 3035.903938] IRQ 125: no longer affine to CPU2
[ 3035.903945] IRQ 129: no longer affine to CPU2
[ 3035.904975] smpboot: CPU 2 is now offline
[ 3035.907258] IRQ 122: no longer affine to CPU3
[ 3035.908291] smpboot: CPU 3 is now offline
[ 3035.913133] ACPI: Low-level resume complete
[ 3035.913206] ACPI: EC: EC started
[ 3035.913207] PM: Restoring platform NVS memory
[ 3035.915616] mce_notify_irq: 2 callbacks suppressed
[ 3035.915616] mce: [Hardware Error]: Machine check events logged
[ 3035.915618] mce: [Hardware Error]: Machine check events logged
[ 3035.915630] Enabling non-boot CPUs ...
[ 3035.915672] x86: Booting SMP configuration:
[ 3035.915673] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 3035.917643]  cache: parent cpu1 should not be sleeping
[ 3035.917683] intel_pstate: Disabling energy efficiency optimization
[ 3035.917753] microcode: sig=0x906e9, pf=0x20, revision=0x48
[ 3035.918853] microcode: updated to revision 0x9a, date = 2018-07-16
[ 3035.918918] CPU1 is up
[ 3035.918936] smpboot: Booting Node 0 Processor 2 APIC 0x4
[ 3035.919317]  cache: parent cpu2 should not be sleeping
[ 3035.920554] CPU2 is up
[ 3035.920572] smpboot: Booting Node 0 Processor 3 APIC 0x6
[ 3035.920936]  cache: parent cpu3 should not be sleeping
[ 3035.922183] CPU3 is up
[ 3035.924668] ACPI: Waking up from system sleep state S3
[ 3035.976203] ACPI: EC: interrupt unblocked
[ 3036.060680] ACPI: EC: event unblocked
[ 3036.062576] sd 2:0:0:0: [sda] Starting disk
[ 3036.174629] usb 2-1: Disable of device-initiated U1 failed.
[ 3036.178126] usb 2-1: Disable of device-initiated U2 failed.
[ 3036.307369] usb 2-1: reset SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[ 3036.455186] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[ 3036.731203] usb 1-6: reset full-speed USB device number 3 using xhci_hcd
[ 3037.007013] usb 1-11: reset high-speed USB device number 4 using xhci_hcd
[ 3037.161069] acpi LNXPOWER:16: Turning OFF
[ 3037.161205] acpi LNXPOWER:15: Turning OFF
[ 3037.161335] acpi LNXPOWER:14: Turning OFF
[ 3037.161445] Bluetooth: hci0: Bootloader revision 0.0 build 26 week 38 2015
[ 3037.161465] acpi LNXPOWER:13: Turning OFF
[ 3037.161595] acpi LNXPOWER:12: Turning OFF
[ 3037.161723] acpi LNXPOWER:11: Turning OFF
[ 3037.161852] acpi LNXPOWER:10: Turning OFF
[ 3037.161981] acpi LNXPOWER:0f: Turning OFF
[ 3037.162109] acpi LNXPOWER:0e: Turning OFF
[ 3037.162238] acpi LNXPOWER:0d: Turning OFF
[ 3037.162365] acpi LNXPOWER:0c: Turning OFF
[ 3037.162456] Bluetooth: hci0: Device revision is 16
[ 3037.162457] Bluetooth: hci0: Secure boot is enabled
[ 3037.162458] Bluetooth: hci0: OTP lock is enabled
[ 3037.162459] Bluetooth: hci0: API lock is enabled
[ 3037.162459] Bluetooth: hci0: Debug lock is disabled
[ 3037.162461] Bluetooth: hci0: Minimum firmware build 1 week 10 2014
[ 3037.162464] Bluetooth: hci0: Found device firmware: intel/ibt-12-16.sfi
[ 3037.162493] acpi LNXPOWER:0b: Turning OFF
[ 3037.162621] acpi LNXPOWER:0a: Turning OFF
[ 3037.162762] acpi LNXPOWER:09: Turning OFF
[ 3037.162890] acpi LNXPOWER:08: Turning OFF
[ 3037.163019] acpi LNXPOWER:07: Turning OFF
[ 3037.163147] acpi LNXPOWER:06: Turning OFF
[ 3037.163275] acpi LNXPOWER:05: Turning OFF
[ 3037.163403] acpi LNXPOWER:04: Turning OFF
[ 3037.163531] acpi LNXPOWER:03: Turning OFF
[ 3037.163626] OOM killer enabled.
[ 3037.163627] Restarting tasks ... done.
[ 3037.231792] PM: suspend exit
[ 3038.646812] Bluetooth: hci0: Waiting for firmware download to complete
[ 3038.647419] Bluetooth: hci0: Firmware loaded in 1452296 usecs
[ 3038.647509] Bluetooth: hci0: Waiting for device to boot
[ 3038.659411] Bluetooth: hci0: Device booted in 11708 usecs
[ 3038.659414] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-12-16.ddc
[ 3038.663434] Bluetooth: hci0: Applying Intel DDC parameters completed
[ 3038.713976] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 3038.716645] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 3038.716648] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 3038.716650] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 3038.717126] ata3.00: ACPI cmd ef/5a:00:00:00:00:a0 (SET FEATURES) succeeded
[ 3038.720892] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 3038.720895] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 3038.720897] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 3038.721187] ata3.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[ 3038.722444] ata3.00: configured for UDMA/100
[ 3038.873345] e1000e: enp0s31f6 NIC Link is Down
[ 3042.708474] wlp1s0: authenticate with 3c:0c:db:d9:1f:b0
[ 3042.715814] wlp1s0: send auth to 3c:0c:db:d9:1f:b0 (try 1/3)
[ 3042.722908] wlp1s0: authenticated
[ 3042.723546] iwlwifi 0000:01:00.0 wlp1s0: disabling HE/HT/VHT due to WEP/TKIP use
[ 3042.724005] wlp1s0: associate with 3c:0c:db:d9:1f:b0 (try 1/3)
[ 3042.730392] wlp1s0: RX AssocResp from 3c:0c:db:d9:1f:b0 (capab=0x411 status=0 aid=1)
[ 3042.733184] wlp1s0: associated
[ 3042.843117] IPv6: ADDRCONF(NETDEV_CHANGE): wlp1s0: link becomes ready
[ 3347.303125] PM: suspend entry (deep)
[ 3347.303128] PM: Syncing filesystems ... done.
[ 3347.304963] Freezing user space processes ... (elapsed 0.001 seconds) done.
[ 3347.306508] OOM killer disabled.
[ 3347.306509] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 3347.307656] printk: Suspending console(s) (use no_console_suspend to debug)
[ 3347.308153] wlp1s0: deauthenticating from 3c:0c:db:d9:1f:b0 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 3347.313039] e1000e: EEE TX LPI TIMER: 00000011
[ 3347.320895] sd 2:0:0:0: [sda] Synchronizing SCSI cache
[ 3347.322309] sd 2:0:0:0: [sda] Stopping disk
[ 3347.609291] ACPI: EC: interrupt blocked
[ 3347.649016] ACPI: Preparing to enter system sleep state S3
[ 3347.656425] ACPI: EC: event blocked
[ 3347.656426] ACPI: EC: EC stopped
[ 3347.656427] PM: Saving platform NVS memory
[ 3347.656520] Disabling non-boot CPUs ...
[ 3347.656867] IRQ 123: no longer affine to CPU1
[ 3347.656872] IRQ 131: no longer affine to CPU1
[ 3347.657883] smpboot: CPU 1 is now offline
[ 3347.659557] IRQ 125: no longer affine to CPU2
[ 3347.659562] IRQ 129: no longer affine to CPU2
[ 3347.660598] smpboot: CPU 2 is now offline
[ 3347.662186] IRQ 122: no longer affine to CPU3
[ 3347.663226] smpboot: CPU 3 is now offline
[ 3347.667088] ACPI: Low-level resume complete
[ 3347.667161] ACPI: EC: EC started
[ 3347.667161] PM: Restoring platform NVS memory
[ 3347.669566] mce_notify_irq: 2 callbacks suppressed
[ 3347.669567] mce: [Hardware Error]: Machine check events logged
[ 3347.669569] mce: [Hardware Error]: Machine check events logged
[ 3347.669584] Enabling non-boot CPUs ...
[ 3347.669624] x86: Booting SMP configuration:
[ 3347.669625] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 3347.670134]  cache: parent cpu1 should not be sleeping
[ 3347.670174] intel_pstate: Disabling energy efficiency optimization
[ 3347.671404] CPU1 is up
[ 3347.671424] smpboot: Booting Node 0 Processor 2 APIC 0x4
[ 3347.671802]  cache: parent cpu2 should not be sleeping
[ 3347.673037] CPU2 is up
[ 3347.673058] smpboot: Booting Node 0 Processor 3 APIC 0x6
[ 3347.673427]  cache: parent cpu3 should not be sleeping
[ 3347.674671] CPU3 is up
[ 3347.677124] ACPI: Waking up from system sleep state S3
[ 3347.728295] ACPI: EC: interrupt unblocked
[ 3347.813284] ACPI: EC: event unblocked
[ 3347.814920] sd 2:0:0:0: [sda] Starting disk
[ 3347.931456] usb 2-1: Disable of device-initiated U1 failed.
[ 3347.934955] usb 2-1: Disable of device-initiated U2 failed.
[ 3348.059958] usb 2-1: reset SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[ 3348.211901] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[ 3348.487934] usb 1-11: reset high-speed USB device number 4 using xhci_hcd
[ 3348.763834] usb 1-6: reset full-speed USB device number 3 using xhci_hcd
[ 3348.914674] acpi LNXPOWER:16: Turning OFF
[ 3348.914810] acpi LNXPOWER:15: Turning OFF
[ 3348.914940] acpi LNXPOWER:14: Turning OFF
[ 3348.915023] Bluetooth: hci0: Bootloader revision 0.0 build 26 week 38 2015
[ 3348.915086] acpi LNXPOWER:13: Turning OFF
[ 3348.915207] acpi LNXPOWER:12: Turning OFF
[ 3348.915328] acpi LNXPOWER:11: Turning OFF
[ 3348.915450] acpi LNXPOWER:10: Turning OFF
[ 3348.915572] acpi LNXPOWER:0f: Turning OFF
[ 3348.915719] acpi LNXPOWER:0e: Turning OFF
[ 3348.915841] acpi LNXPOWER:0d: Turning OFF
[ 3348.915962] acpi LNXPOWER:0c: Turning OFF
[ 3348.916026] Bluetooth: hci0: Device revision is 16
[ 3348.916027] Bluetooth: hci0: Secure boot is enabled
[ 3348.916028] Bluetooth: hci0: OTP lock is enabled
[ 3348.916029] Bluetooth: hci0: API lock is enabled
[ 3348.916030] Bluetooth: hci0: Debug lock is disabled
[ 3348.916031] Bluetooth: hci0: Minimum firmware build 1 week 10 2014
[ 3348.916082] acpi LNXPOWER:0b: Turning OFF
[ 3348.916205] acpi LNXPOWER:0a: Turning OFF
[ 3348.916250] Bluetooth: hci0: Found device firmware: intel/ibt-12-16.sfi
[ 3348.916326] acpi LNXPOWER:09: Turning OFF
[ 3348.916446] acpi LNXPOWER:08: Turning OFF
[ 3348.916567] acpi LNXPOWER:07: Turning OFF
[ 3348.916687] acpi LNXPOWER:06: Turning OFF
[ 3348.916807] acpi LNXPOWER:05: Turning OFF
[ 3348.916928] acpi LNXPOWER:04: Turning OFF
[ 3348.917048] acpi LNXPOWER:03: Turning OFF
[ 3348.917137] OOM killer enabled.
[ 3348.917138] Restarting tasks ... done.
[ 3349.007529] PM: suspend exit
[ 3350.499460] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 3350.502082] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 3350.502085] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 3350.502087] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 3350.502441] ata3.00: ACPI cmd ef/5a:00:00:00:00:a0 (SET FEATURES) succeeded
[ 3350.506392] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 3350.506395] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 3350.506397] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 3350.506747] ata3.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[ 3350.508156] ata3.00: configured for UDMA/100
[ 3350.580349] Bluetooth: hci0: Waiting for firmware download to complete
[ 3350.580991] Bluetooth: hci0: Firmware loaded in 1627606 usecs
[ 3350.581061] Bluetooth: hci0: Waiting for device to boot
[ 3350.592989] Bluetooth: hci0: Device booted in 11697 usecs
[ 3350.593102] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-12-16.ddc
[ 3350.598039] Bluetooth: hci0: Applying Intel DDC parameters completed
[ 3350.667628] e1000e: enp0s31f6 NIC Link is Down
[ 3354.552271] wlp1s0: authenticate with 3c:0c:db:d9:1f:b0
[ 3354.559793] wlp1s0: send auth to 3c:0c:db:d9:1f:b0 (try 1/3)
[ 3354.567914] wlp1s0: authenticated
[ 3354.568140] iwlwifi 0000:01:00.0 wlp1s0: disabling HE/HT/VHT due to WEP/TKIP use
[ 3354.570802] wlp1s0: associate with 3c:0c:db:d9:1f:b0 (try 1/3)
[ 3354.577232] wlp1s0: RX AssocResp from 3c:0c:db:d9:1f:b0 (capab=0x411 status=0 aid=3)
[ 3354.582725] wlp1s0: associated
[ 3354.687620] IPv6: ADDRCONF(NETDEV_CHANGE): wlp1s0: link becomes ready
[ 4362.627351] PM: suspend entry (deep)
[ 4362.627352] PM: Syncing filesystems ... done.
[ 4362.628351] Freezing user space processes ... (elapsed 0.001 seconds) done.
[ 4362.629827] OOM killer disabled.
[ 4362.629828] Freezing remaining freezable tasks ... (elapsed 0.000 seconds) done.
[ 4362.630766] printk: Suspending console(s) (use no_console_suspend to debug)
[ 4362.631521] wlp1s0: deauthenticating from 3c:0c:db:d9:1f:b0 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 4362.658172] sd 2:0:0:0: [sda] Synchronizing SCSI cache
[ 4362.659629] sd 2:0:0:0: [sda] Stopping disk
[ 4362.745228] e1000e: EEE TX LPI TIMER: 00000011
[ 4363.031192] ACPI: EC: interrupt blocked
[ 4363.071059] ACPI: Preparing to enter system sleep state S3
[ 4363.078825] ACPI: EC: event blocked
[ 4363.078825] ACPI: EC: EC stopped
[ 4363.078826] PM: Saving platform NVS memory
[ 4363.078920] Disabling non-boot CPUs ...
[ 4363.079285] IRQ 123: no longer affine to CPU1
[ 4363.079291] IRQ 131: no longer affine to CPU1
[ 4363.080311] smpboot: CPU 1 is now offline
[ 4363.082049] IRQ 125: no longer affine to CPU2
[ 4363.082054] IRQ 129: no longer affine to CPU2
[ 4363.083086] smpboot: CPU 2 is now offline
[ 4363.084772] IRQ 122: no longer affine to CPU3
[ 4363.085823] smpboot: CPU 3 is now offline
[ 4363.089867] ACPI: Low-level resume complete
[ 4363.089941] ACPI: EC: EC started
[ 4363.089941] PM: Restoring platform NVS memory
[ 4363.092345] mce_notify_irq: 2 callbacks suppressed
[ 4363.092345] mce: [Hardware Error]: Machine check events logged
[ 4363.092347] mce: [Hardware Error]: Machine check events logged
[ 4363.092367] Enabling non-boot CPUs ...
[ 4363.092408] x86: Booting SMP configuration:
[ 4363.092409] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 4363.092914]  cache: parent cpu1 should not be sleeping
[ 4363.092955] intel_pstate: Disabling energy efficiency optimization
[ 4363.094257] CPU1 is up
[ 4363.094278] smpboot: Booting Node 0 Processor 2 APIC 0x4
[ 4363.094638]  cache: parent cpu2 should not be sleeping
[ 4363.095875] CPU2 is up
[ 4363.095893] smpboot: Booting Node 0 Processor 3 APIC 0x6
[ 4363.096261]  cache: parent cpu3 should not be sleeping
[ 4363.097510] CPU3 is up
[ 4363.100000] ACPI: Waking up from system sleep state S3
[ 4363.167964] ACPI: EC: interrupt unblocked
[ 4363.210716] ACPI: EC: event unblocked
[ 4363.212109] sd 2:0:0:0: [sda] Starting disk
[ 4363.325281] usb 2-1: Disable of device-initiated U1 failed.
[ 4363.328804] usb 2-1: Disable of device-initiated U2 failed.
[ 4363.454048] usb 2-1: reset SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[ 4363.602053] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[ 4363.878084] usb 1-6: reset full-speed USB device number 3 using xhci_hcd
[ 4364.154045] usb 1-11: reset high-speed USB device number 4 using xhci_hcd
[ 4364.308397] acpi LNXPOWER:16: Turning OFF
[ 4364.308587] acpi LNXPOWER:15: Turning OFF
[ 4364.308765] acpi LNXPOWER:14: Turning OFF
[ 4364.308934] acpi LNXPOWER:13: Turning OFF
[ 4364.309139] acpi LNXPOWER:12: Turning OFF
[ 4364.309304] acpi LNXPOWER:11: Turning OFF
[ 4364.309494] acpi LNXPOWER:10: Turning OFF
[ 4364.309496] Bluetooth: hci0: Bootloader revision 0.0 build 26 week 38 2015
[ 4364.309683] acpi LNXPOWER:0f: Turning OFF
[ 4364.309879] acpi LNXPOWER:0e: Turning OFF
[ 4364.310058] acpi LNXPOWER:0d: Turning OFF
[ 4364.310225] acpi LNXPOWER:0c: Turning OFF
[ 4364.310402] acpi LNXPOWER:0b: Turning OFF
[ 4364.310519] Bluetooth: hci0: Device revision is 16
[ 4364.310521] Bluetooth: hci0: Secure boot is enabled
[ 4364.310522] Bluetooth: hci0: OTP lock is enabled
[ 4364.310522] Bluetooth: hci0: API lock is enabled
[ 4364.310523] Bluetooth: hci0: Debug lock is disabled
[ 4364.310525] Bluetooth: hci0: Minimum firmware build 1 week 10 2014
[ 4364.310528] Bluetooth: hci0: Found device firmware: intel/ibt-12-16.sfi
[ 4364.310583] acpi LNXPOWER:0a: Turning OFF
[ 4364.310744] acpi LNXPOWER:09: Turning OFF
[ 4364.310930] acpi LNXPOWER:08: Turning OFF
[ 4364.311096] acpi LNXPOWER:07: Turning OFF
[ 4364.311263] acpi LNXPOWER:06: Turning OFF
[ 4364.311445] acpi LNXPOWER:05: Turning OFF
[ 4364.311670] acpi LNXPOWER:04: Turning OFF
[ 4364.311835] acpi LNXPOWER:03: Turning OFF
[ 4364.311955] OOM killer enabled.
[ 4364.311955] Restarting tasks ... done.
[ 4364.384869] PM: suspend exit
[ 4365.817123] Bluetooth: hci0: Waiting for firmware download to complete
[ 4365.817451] Bluetooth: hci0: Firmware loaded in 1473887 usecs
[ 4365.817533] Bluetooth: hci0: Waiting for device to boot
[ 4365.829450] Bluetooth: hci0: Device booted in 11713 usecs
[ 4365.829453] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-12-16.ddc
[ 4365.833472] Bluetooth: hci0: Applying Intel DDC parameters completed
[ 4365.877704] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 4365.880553] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 4365.880556] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 4365.880564] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 4365.880846] ata3.00: ACPI cmd ef/5a:00:00:00:00:a0 (SET FEATURES) succeeded
[ 4365.884732] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 4365.884735] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 4365.884738] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 4365.885026] ata3.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[ 4365.886280] ata3.00: configured for UDMA/100
[ 4366.028904] e1000e: enp0s31f6 NIC Link is Down
[ 4369.866508] wlp1s0: authenticate with 3c:0c:db:d9:1f:b0
[ 4369.873852] wlp1s0: send auth to 3c:0c:db:d9:1f:b0 (try 1/3)
[ 4369.881230] wlp1s0: authenticated
[ 4369.881405] iwlwifi 0000:01:00.0 wlp1s0: disabling HE/HT/VHT due to WEP/TKIP use
[ 4369.881475] wlp1s0: associate with 3c:0c:db:d9:1f:b0 (try 1/3)
[ 4369.889113] wlp1s0: RX AssocResp from 3c:0c:db:d9:1f:b0 (capab=0x411 status=0 aid=3)
[ 4369.891914] wlp1s0: associated
[ 4370.003132] IPv6: ADDRCONF(NETDEV_CHANGE): wlp1s0: link becomes ready
[ 4396.960934] PM: suspend entry (deep)
[ 4396.960936] PM: Syncing filesystems ... done.
[ 4396.961802] Freezing user space processes ... (elapsed 0.001 seconds) done.
[ 4396.963313] OOM killer disabled.
[ 4396.963314] Freezing remaining freezable tasks ... (elapsed 0.000 seconds) done.
[ 4396.964129] printk: Suspending console(s) (use no_console_suspend to debug)
[ 4396.964840] wlp1s0: deauthenticating from 3c:0c:db:d9:1f:b0 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 4396.969630] e1000e: EEE TX LPI TIMER: 00000011
[ 4397.004637] sd 2:0:0:0: [sda] Synchronizing SCSI cache
[ 4397.004723] sd 2:0:0:0: [sda] Stopping disk
[ 4397.752604] ACPI: EC: interrupt blocked
[ 4397.792413] ACPI: Preparing to enter system sleep state S3
[ 4397.798113] ACPI: EC: event blocked
[ 4397.798114] ACPI: EC: EC stopped
[ 4397.798114] PM: Saving platform NVS memory
[ 4397.798173] Disabling non-boot CPUs ...
[ 4397.798378] IRQ 123: no longer affine to CPU1
[ 4397.798381] IRQ 131: no longer affine to CPU1
[ 4397.799384] smpboot: CPU 1 is now offline
[ 4397.800256] IRQ 125: no longer affine to CPU2
[ 4397.800259] IRQ 129: no longer affine to CPU2
[ 4397.801260] smpboot: CPU 2 is now offline
[ 4397.802135] IRQ 122: no longer affine to CPU3
[ 4397.803142] smpboot: CPU 3 is now offline
[ 4397.806235] ACPI: Low-level resume complete
[ 4397.806307] ACPI: EC: EC started
[ 4397.806308] PM: Restoring platform NVS memory
[ 4397.808742] Enabling non-boot CPUs ...
[ 4397.808783] x86: Booting SMP configuration:
[ 4397.808784] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 4397.809312]  cache: parent cpu1 should not be sleeping
[ 4397.809350] intel_pstate: Disabling energy efficiency optimization
[ 4397.810585] CPU1 is up
[ 4397.810605] smpboot: Booting Node 0 Processor 2 APIC 0x4
[ 4397.811006]  cache: parent cpu2 should not be sleeping
[ 4397.812238] CPU2 is up
[ 4397.812260] smpboot: Booting Node 0 Processor 3 APIC 0x6
[ 4397.812643]  cache: parent cpu3 should not be sleeping
[ 4397.813889] CPU3 is up
[ 4397.816370] ACPI: Waking up from system sleep state S3
[ 4397.868007] ACPI: EC: interrupt unblocked
[ 4397.952346] ACPI: EC: event unblocked
[ 4397.953816] sd 2:0:0:0: [sda] Starting disk
[ 4398.066666] usb 2-1: Disable of device-initiated U1 failed.
[ 4398.070155] usb 2-1: Disable of device-initiated U2 failed.
[ 4398.195223] usb 2-1: reset SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[ 4398.343211] usb 1-6: reset full-speed USB device number 3 using xhci_hcd
[ 4398.619067] usb 1-11: reset high-speed USB device number 4 using xhci_hcd
[ 4398.895164] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[ 4399.092978] acpi LNXPOWER:16: Turning OFF
[ 4399.093130] acpi LNXPOWER:15: Turning OFF
[ 4399.093297] acpi LNXPOWER:14: Turning OFF
[ 4399.093427] acpi LNXPOWER:13: Turning OFF
[ 4399.093561] acpi LNXPOWER:12: Turning OFF
[ 4399.093703] acpi LNXPOWER:11: Turning OFF
[ 4399.093837] acpi LNXPOWER:10: Turning OFF
[ 4399.093972] acpi LNXPOWER:0f: Turning OFF
[ 4399.094100] Bluetooth: hci0: Bootloader revision 0.0 build 26 week 38 2015
[ 4399.094129] acpi LNXPOWER:0e: Turning OFF
[ 4399.094268] acpi LNXPOWER:0d: Turning OFF
[ 4399.094409] acpi LNXPOWER:0c: Turning OFF
[ 4399.094544] acpi LNXPOWER:0b: Turning OFF
[ 4399.094678] acpi LNXPOWER:0a: Turning OFF
[ 4399.094805] acpi LNXPOWER:09: Turning OFF
[ 4399.094952] acpi LNXPOWER:08: Turning OFF
[ 4399.095071] acpi LNXPOWER:07: Turning OFF
[ 4399.095099] Bluetooth: hci0: Device revision is 16
[ 4399.095099] Bluetooth: hci0: Secure boot is enabled
[ 4399.095100] Bluetooth: hci0: OTP lock is enabled
[ 4399.095101] Bluetooth: hci0: API lock is enabled
[ 4399.095101] Bluetooth: hci0: Debug lock is disabled
[ 4399.095102] Bluetooth: hci0: Minimum firmware build 1 week 10 2014
[ 4399.095181] acpi LNXPOWER:06: Turning OFF
[ 4399.095282] Bluetooth: hci0: Found device firmware: intel/ibt-12-16.sfi
[ 4399.095296] acpi LNXPOWER:05: Turning OFF
[ 4399.095405] acpi LNXPOWER:04: Turning OFF
[ 4399.095514] acpi LNXPOWER:03: Turning OFF
[ 4399.095617] OOM killer enabled.
[ 4399.095617] Restarting tasks ... done.
[ 4399.170156] PM: suspend exit
[ 4400.577727] Bluetooth: hci0: Waiting for firmware download to complete
[ 4400.578061] Bluetooth: hci0: Firmware loaded in 1450404 usecs
[ 4400.578190] Bluetooth: hci0: Waiting for device to boot
[ 4400.590076] Bluetooth: hci0: Device booted in 11696 usecs
[ 4400.590153] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-12-16.ddc
[ 4400.594120] Bluetooth: hci0: Applying Intel DDC parameters completed
[ 4400.606824] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 4400.609717] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 4400.609719] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 4400.609722] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 4400.610023] ata3.00: ACPI cmd ef/5a:00:00:00:00:a0 (SET FEATURES) succeeded
[ 4400.613884] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 4400.613887] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 4400.613890] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 4400.614201] ata3.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[ 4400.615434] ata3.00: configured for UDMA/100
[ 4400.774032] e1000e: enp0s31f6 NIC Link is Down
[ 4404.629980] wlp1s0: authenticate with 3c:0c:db:d9:1f:b0
[ 4404.637101] wlp1s0: send auth to 3c:0c:db:d9:1f:b0 (try 1/3)
[ 4404.746607] wlp1s0: send auth to 3c:0c:db:d9:1f:b0 (try 2/3)
[ 4404.748546] wlp1s0: authenticated
[ 4404.749082] iwlwifi 0000:01:00.0 wlp1s0: disabling HE/HT/VHT due to WEP/TKIP use
[ 4404.750692] wlp1s0: associate with 3c:0c:db:d9:1f:b0 (try 1/3)
[ 4404.757281] wlp1s0: RX AssocResp from 3c:0c:db:d9:1f:b0 (capab=0x411 status=0 aid=3)
[ 4404.760013] wlp1s0: associated
[ 4404.862988] IPv6: ADDRCONF(NETDEV_CHANGE): wlp1s0: link becomes ready
[11396.354488] PM: suspend entry (deep)
[11396.354493] PM: Syncing filesystems ... done.
[11396.356442] Freezing user space processes ... (elapsed 0.001 seconds) done.
[11396.358259] OOM killer disabled.
[11396.358259] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[11396.359595] printk: Suspending console(s) (use no_console_suspend to debug)
[11396.361132] wlp1s0: deauthenticating from 3c:0c:db:d9:1f:b0 by local choice (Reason: 3=DEAUTH_LEAVING)
[11396.382130] sd 2:0:0:0: [sda] Synchronizing SCSI cache
[11396.383549] sd 2:0:0:0: [sda] Stopping disk
[11396.476482] e1000e: EEE TX LPI TIMER: 00000011
[11396.770490] ACPI: EC: interrupt blocked
[11396.810262] ACPI: Preparing to enter system sleep state S3
[11396.818040] ACPI: EC: event blocked
[11396.818041] ACPI: EC: EC stopped
[11396.818042] PM: Saving platform NVS memory
[11396.818138] Disabling non-boot CPUs ...
[11396.818502] IRQ 123: no longer affine to CPU1
[11396.818508] IRQ 131: no longer affine to CPU1
[11396.819523] smpboot: CPU 1 is now offline
[11396.821277] IRQ 125: no longer affine to CPU2
[11396.821282] IRQ 129: no longer affine to CPU2
[11396.822313] smpboot: CPU 2 is now offline
[11396.824001] IRQ 122: no longer affine to CPU3
[11396.825019] smpboot: CPU 3 is now offline
[11396.826794] ACPI Error: AE_BAD_PARAMETER, Returned by Handler for [EmbeddedControl] (20181213/evregion-266)
[11396.826807] 
               Initialized Local Variables for Method [ECR1]:
[11396.826808]   Local0: 0000000073aa97c0 <Obj>           Integer 0000000000000000
[11396.826815] Initialized Arguments for Method [ECR1]:  (1 arguments defined for method invocation)
[11396.826816]   Arg0:   00000000b81d8ac8 <Obj>           Integer 0000000000000007
[11396.826822] ACPI Error: Method parse/execution failed \_SB.PCI0.LPCB.ECDV.ECR1, AE_BAD_PARAMETER (20181213/psparse-531)
[11396.826829] ACPI Error: Method parse/execution failed \_SB.PCI0.LPCB.ECDV.ECR2, AE_BAD_PARAMETER (20181213/psparse-531)
[11396.826834] ACPI Error: Method parse/execution failed \ECRW, AE_BAD_PARAMETER (20181213/psparse-531)
[11396.826840] ACPI Error: Method parse/execution failed \ECG1, AE_BAD_PARAMETER (20181213/psparse-531)
[11396.826844] ACPI Error: Method parse/execution failed \NEVT, AE_BAD_PARAMETER (20181213/psparse-531)
[11396.826851] ACPI Error: Method parse/execution failed \_SB.PCI0.LPCB.ECDV._Q66, AE_BAD_PARAMETER (20181213/psparse-531)
[11396.827056] ACPI Error: AE_BAD_PARAMETER, Returned by Handler for [EmbeddedControl] (20181213/evregion-266)
[11396.827064] 
               Initialized Local Variables for Method [ECR1]:
[11396.827065]   Local0: 00000000b81d8ac8 <Obj>           Integer 0000000000000000
[11396.827070] Initialized Arguments for Method [ECR1]:  (1 arguments defined for method invocation)
[11396.827070]   Arg0:   000000007044eae5 <Obj>           Integer 0000000000000007
[11396.827075] ACPI Error: Method parse/execution failed \_SB.PCI0.LPCB.ECDV.ECR1, AE_BAD_PARAMETER (20181213/psparse-531)
[11396.827080] ACPI Error: Method parse/execution failed \_SB.PCI0.LPCB.ECDV.ECR2, AE_BAD_PARAMETER (20181213/psparse-531)
[11396.827086] ACPI Error: Method parse/execution failed \ECRW, AE_BAD_PARAMETER (20181213/psparse-531)
[11396.827091] ACPI Error: Method parse/execution failed \ECG1, AE_BAD_PARAMETER (20181213/psparse-531)
[11396.827095] ACPI Error: Method parse/execution failed \NEVT, AE_BAD_PARAMETER (20181213/psparse-531)
[11396.827100] ACPI Error: Method parse/execution failed \_SB.PCI0.LPCB.ECDV._Q66, AE_BAD_PARAMETER (20181213/psparse-531)
[11396.829723] ACPI: Low-level resume complete
[11396.829795] ACPI: EC: EC started
[11396.829796] PM: Restoring platform NVS memory
[11396.832205] mce_notify_irq: 6 callbacks suppressed
[11396.832206] mce: [Hardware Error]: Machine check events logged
[11396.832208] mce: [Hardware Error]: Machine check events logged
[11396.832224] Enabling non-boot CPUs ...
[11396.832266] x86: Booting SMP configuration:
[11396.832266] smpboot: Booting Node 0 Processor 1 APIC 0x2
[11396.832770]  cache: parent cpu1 should not be sleeping
[11396.832808] intel_pstate: Disabling energy efficiency optimization
[11396.834095] CPU1 is up
[11396.834115] smpboot: Booting Node 0 Processor 2 APIC 0x4
[11396.834480]  cache: parent cpu2 should not be sleeping
[11396.835718] CPU2 is up
[11396.835742] smpboot: Booting Node 0 Processor 3 APIC 0x6
[11396.836107]  cache: parent cpu3 should not be sleeping
[11396.837397] CPU3 is up
[11396.839822] ACPI: Waking up from system sleep state S3
[11396.890328] ACPI: EC: interrupt unblocked
[11396.974439] ACPI: EC: event unblocked
[11396.975957] sd 2:0:0:0: [sda] Starting disk
[11397.088368] usb 2-1: Disable of device-initiated U1 failed.
[11397.091866] usb 2-1: Disable of device-initiated U2 failed.
[11397.217076] usb 2-1: reset SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[11397.368987] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[11397.644819] usb 1-6: reset full-speed USB device number 3 using xhci_hcd
[11397.920712] usb 1-11: reset high-speed USB device number 4 using xhci_hcd
[11398.074805] acpi LNXPOWER:16: Turning OFF
[11398.074933] acpi LNXPOWER:15: Turning OFF
[11398.075056] acpi LNXPOWER:14: Turning OFF
[11398.075179] acpi LNXPOWER:13: Turning OFF
[11398.075193] Bluetooth: hci0: Bootloader revision 0.0 build 26 week 38 2015
[11398.075300] acpi LNXPOWER:12: Turning OFF
[11398.075421] acpi LNXPOWER:11: Turning OFF
[11398.075543] acpi LNXPOWER:10: Turning OFF
[11398.075664] acpi LNXPOWER:0f: Turning OFF
[11398.075785] acpi LNXPOWER:0e: Turning OFF
[11398.075907] acpi LNXPOWER:0d: Turning OFF
[11398.076027] acpi LNXPOWER:0c: Turning OFF
[11398.076147] acpi LNXPOWER:0b: Turning OFF
[11398.076180] Bluetooth: hci0: Device revision is 16
[11398.076181] Bluetooth: hci0: Secure boot is enabled
[11398.076182] Bluetooth: hci0: OTP lock is enabled
[11398.076183] Bluetooth: hci0: API lock is enabled
[11398.076183] Bluetooth: hci0: Debug lock is disabled
[11398.076184] Bluetooth: hci0: Minimum firmware build 1 week 10 2014
[11398.076187] Bluetooth: hci0: Found device firmware: intel/ibt-12-16.sfi
[11398.076268] acpi LNXPOWER:0a: Turning OFF
[11398.076409] acpi LNXPOWER:09: Turning OFF
[11398.076535] acpi LNXPOWER:08: Turning OFF
[11398.076657] acpi LNXPOWER:07: Turning OFF
[11398.076778] acpi LNXPOWER:06: Turning OFF
[11398.076899] acpi LNXPOWER:05: Turning OFF
[11398.077020] acpi LNXPOWER:04: Turning OFF
[11398.077140] acpi LNXPOWER:03: Turning OFF
[11398.077230] OOM killer enabled.
[11398.077231] Restarting tasks ... done.
[11398.160538] PM: suspend exit
[11399.550791] Bluetooth: hci0: Waiting for firmware download to complete
[11399.551119] Bluetooth: hci0: Firmware loaded in 1442529 usecs
[11399.551158] Bluetooth: hci0: Waiting for device to boot
[11399.563125] Bluetooth: hci0: Device booted in 11727 usecs
[11399.563128] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-12-16.ddc
[11399.567175] Bluetooth: hci0: Applying Intel DDC parameters completed
[11399.631643] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[11399.634632] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[11399.634635] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[11399.634637] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[11399.634936] ata3.00: ACPI cmd ef/5a:00:00:00:00:a0 (SET FEATURES) succeeded
[11399.639098] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[11399.639101] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[11399.639126] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[11399.639430] ata3.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[11399.640755] ata3.00: configured for UDMA/100
[11399.787805] e1000e: enp0s31f6 NIC Link is Down
[11400.592487] PM: suspend entry (deep)
[11400.592489] PM: Syncing filesystems ... done.
[11400.592797] Freezing user space processes ... (elapsed 0.001 seconds) done.
[11400.594363] OOM killer disabled.
[11400.594364] Freezing remaining freezable tasks ... (elapsed 0.020 seconds) done.
[11400.615302] printk: Suspending console(s) (use no_console_suspend to debug)
[11400.633517] e1000e: EEE TX LPI TIMER: 00000011
[11400.639444] sd 2:0:0:0: [sda] Synchronizing SCSI cache
[11400.639556] sd 2:0:0:0: [sda] Stopping disk
[11401.383330] ACPI: EC: interrupt blocked
[11401.423173] ACPI: Preparing to enter system sleep state S3
[11401.430631] ACPI: EC: event blocked
[11401.430632] ACPI: EC: EC stopped
[11401.430632] PM: Saving platform NVS memory
[11401.430693] Disabling non-boot CPUs ...
[11401.431903] smpboot: CPU 1 is now offline
[11401.433913] smpboot: CPU 2 is now offline
[11401.435914] smpboot: CPU 3 is now offline
[11401.439061] ACPI: Low-level resume complete
[11401.439134] ACPI: EC: EC started
[11401.439134] PM: Restoring platform NVS memory
[11401.441528] Enabling non-boot CPUs ...
[11401.441570] x86: Booting SMP configuration:
[11401.441571] smpboot: Booting Node 0 Processor 1 APIC 0x2
[11401.442101]  cache: parent cpu1 should not be sleeping
[11401.442141] intel_pstate: Disabling energy efficiency optimization
[11401.443371] CPU1 is up
[11401.443390] smpboot: Booting Node 0 Processor 2 APIC 0x4
[11401.443774]  cache: parent cpu2 should not be sleeping
[11401.445012] CPU2 is up
[11401.445031] smpboot: Booting Node 0 Processor 3 APIC 0x6
[11401.445417]  cache: parent cpu3 should not be sleeping
[11401.446712] CPU3 is up
[11401.449140] ACPI: Waking up from system sleep state S3
[11401.500863] ACPI: EC: interrupt unblocked
[11401.583225] ACPI: EC: event unblocked
[11401.585007] sd 2:0:0:0: [sda] Starting disk
[11401.697037] usb 2-1: Disable of device-initiated U1 failed.
[11401.700555] usb 2-1: Disable of device-initiated U2 failed.
[11401.825769] usb 2-1: reset SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[11401.973718] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[11402.249540] usb 1-6: reset full-speed USB device number 3 using xhci_hcd
[11402.525318] usb 1-11: reset high-speed USB device number 4 using xhci_hcd
[11402.679436] acpi LNXPOWER:16: Turning OFF
[11402.679609] acpi LNXPOWER:15: Turning OFF
[11402.679780] acpi LNXPOWER:14: Turning OFF
[11402.680135] acpi LNXPOWER:13: Turning OFF
[11402.680320] acpi LNXPOWER:12: Turning OFF
[11402.680499] acpi LNXPOWER:11: Turning OFF
[11402.680663] acpi LNXPOWER:10: Turning OFF
[11402.680842] acpi LNXPOWER:0f: Turning OFF
[11402.681018] Bluetooth: hci0: Bootloader revision 0.0 build 26 week 38 2015
[11402.681032] acpi LNXPOWER:0e: Turning OFF
[11402.681236] acpi LNXPOWER:0d: Turning OFF
[11402.681411] acpi LNXPOWER:0c: Turning OFF
[11402.681578] acpi LNXPOWER:0b: Turning OFF
[11402.681756] acpi LNXPOWER:0a: Turning OFF
[11402.681923] acpi LNXPOWER:09: Turning OFF
[11402.682021] Bluetooth: hci0: Device revision is 16
[11402.682022] Bluetooth: hci0: Secure boot is enabled
[11402.682023] Bluetooth: hci0: OTP lock is enabled
[11402.682024] Bluetooth: hci0: API lock is enabled
[11402.682024] Bluetooth: hci0: Debug lock is disabled
[11402.682026] Bluetooth: hci0: Minimum firmware build 1 week 10 2014
[11402.682029] Bluetooth: hci0: Found device firmware: intel/ibt-12-16.sfi
[11402.682117] acpi LNXPOWER:08: Turning OFF
[11402.682320] acpi LNXPOWER:07: Turning OFF
[11402.682513] acpi LNXPOWER:06: Turning OFF
[11402.682683] acpi LNXPOWER:05: Turning OFF
[11402.682867] acpi LNXPOWER:04: Turning OFF
[11402.683054] acpi LNXPOWER:03: Turning OFF
[11402.683206] OOM killer enabled.
[11402.683207] Restarting tasks ... done.
[11402.821345] PM: suspend exit
[11404.159105] Bluetooth: hci0: Waiting for firmware download to complete
[11404.159925] Bluetooth: hci0: Firmware loaded in 1445933 usecs
[11404.159963] Bluetooth: hci0: Waiting for device to boot
[11404.171949] Bluetooth: hci0: Device booted in 11745 usecs
[11404.171971] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-12-16.ddc
[11404.174994] Bluetooth: hci0: Applying Intel DDC parameters completed
[11404.200377] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[11404.202424] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[11404.202425] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[11404.202426] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[11404.202737] ata3.00: ACPI cmd ef/5a:00:00:00:00:a0 (SET FEATURES) succeeded
[11404.205957] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[11404.205959] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[11404.205960] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[11404.206262] ata3.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[11404.207480] ata3.00: configured for UDMA/100
[11404.360173] e1000e: enp0s31f6 NIC Link is Down
[11408.142751] wlp1s0: authenticate with 3c:0c:db:d9:1f:b0
[11408.150549] wlp1s0: send auth to 3c:0c:db:d9:1f:b0 (try 1/3)
[11408.157674] wlp1s0: authenticated
[11408.157810] iwlwifi 0000:01:00.0 wlp1s0: disabling HE/HT/VHT due to WEP/TKIP use
[11408.162369] wlp1s0: associate with 3c:0c:db:d9:1f:b0 (try 1/3)
[11408.168917] wlp1s0: RX AssocResp from 3c:0c:db:d9:1f:b0 (capab=0x411 status=0 aid=3)
[11408.177173] wlp1s0: associated
[11408.288419] IPv6: ADDRCONF(NETDEV_CHANGE): wlp1s0: link becomes ready

Offline

#4 2019-07-02 13:20:13

seth
Member
Registered: 2012-09-03
Posts: 58,672

Re: cannot run smartctl on drive

[    0.000000] Linux version 5.0.0-13-generic (buildd@lcy01-amd64-020) (gcc version 8.3.0 (Ubuntu 8.3.0-6ubuntu1)) #14-Ubuntu SMP Mon Apr 15 14:59:14 UTC 2019 (Ubuntu 5.0.0-13.14-generic 5.0.6)

You're using a ubuntu live system because you can't boot from the drive anymore?

  3 Spin_Up_Time            0x0027   100   100   001    Pre-fail  Always       -       1979
  5 Reallocated_Sector_Ct   0x0033   100   100   050    Pre-fail  Always       -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       3
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       8
…
Error 40 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 50 01 01 00 00 00

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  aa aa aa aa aa aa aa ff      00:21:29.893  [RESERVED]
  35 00 60 08 a0 ee e0 00      00:21:29.834  WRITE DMA EXT
  25 00 08 00 a0 72 e0 00      00:21:29.828  READ DMA EXT
  25 00 08 18 c1 ee e0 00      00:21:29.823  READ DMA EXT
  25 00 00 e0 a0 ee e0 00      00:21:29.814  READ DMA EXT

Error 39 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 50 01 01 00 00 00

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  aa aa aa aa aa aa aa ff      00:21:26.742  [RESERVED]
  35 00 08 18 e6 34 e0 00      00:21:26.674  WRITE DMA EXT
  ef 10 02 00 00 00 a0 00      00:21:26.673  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 a0 00      00:21:26.672  IDENTIFY DEVICE
  ef 03 45 00 00 00 a0 00      00:21:26.672  SET FEATURES [Set transfer mode]

Error 38 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 50 01 01 00 00 00

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  aa aa aa aa aa aa aa ff      00:21:26.042  [RESERVED]
  35 00 08 58 aa 2e e0 00      00:21:26.014  WRITE DMA EXT
  ef 10 02 00 00 00 a0 00      00:21:26.013  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 a0 00      00:21:26.012  IDENTIFY DEVICE
  ef 03 45 00 00 00 a0 00      00:21:26.012  SET FEATURES [Set transfer mode]

Error 37 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 50 01 01 00 00 00

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  aa aa aa aa aa aa aa ff      00:21:25.392  [RESERVED]
  35 00 18 58 a9 2e e0 00      00:21:25.324  WRITE DMA EXT
  ef 10 02 00 00 00 a0 00      00:21:25.323  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 a0 00      00:21:25.322  IDENTIFY DEVICE
  ef 03 45 00 00 00 a0 00      00:21:25.322  SET FEATURES [Set transfer mode]

Error 36 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 50 01 01 00 00 00

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  aa aa aa aa aa aa aa ff      00:21:22.213  [RESERVED]
  aa aa aa aa aa aa aa ff      00:21:22.183  [RESERVED]
  25 00 40 40 e3 1f 40 00      00:21:20.185  READ DMA EXT
  25 00 40 00 e3 1f 40 00      00:21:20.177  READ DMA EXT
  25 00 40 c0 e2 1f 40 00      00:21:20.168  READ DMA EXT

Some data certainly makes no sense, secure all data you can obtain. It seems the controller chip took a hit.

Online

#5 2019-07-02 13:59:41

frostschutz
Member
Registered: 2013-11-15
Posts: 1,471

Re: cannot run smartctl on drive

power on hours: 3

power on hours when selftest ran: 2000+ hours

did you buy it on ebay?

Offline

#6 2019-07-02 16:19:21

Portal
Member
Registered: 2019-03-11
Posts: 48

Re: cannot run smartctl on drive

seth wrote:

You're using a ubuntu live system because you can't boot from the drive anymore?

yes

seth wrote:

Some data certainly makes no sense, secure all data you can obtain. It seems the controller chip took a hit

Is that why smartctl doesn't work? How do I secure data if I can't boot from it?

frostschutz wrote:

power on hours: 3

power on hours when selftest ran: 2000+ hours

did you buy it on ebay?

The drive came from a new dell precision, but it definitely has been powered on for more than 3 hours...
where are you seeing these numbers?

Last edited by Portal (2019-07-02 16:20:54)

Offline

#7 2019-07-02 16:28:49

seth
Member
Registered: 2012-09-03
Posts: 58,672

Re: cannot run smartctl on drive

Try to mount the precious partition/s (your private data, the stuff where there's only one copy if you don't have a backup) from any live system and copy the data to another drive.

Uptime etc. are in your smartctl -a output. It's impossible to say (for us) what happened to the disk, but I've seen this kind of behavior from overheated disks.
What we can say is that a disk showing this behavior is no more trustworthy.

Just to be sure (because the dmesg doesn't suggest otherwise): this is attached directly to an ATA controller (w/ a sata cable) and there's no adapter? (Because those tend to screw "irrelevant" ATA commands like the SMART stuff)

Online

#8 2020-03-29 04:39:42

anelson0528
Member
Registered: 2020-03-29
Posts: 1

Re: cannot run smartctl on drive

I'm having a very similar problem with a Dell XPS 13 9350:

smartctl -a /dev/sda

gives

smartctl 6.6 2016-05-31 r4324 [x86_64-linux-5.3.0-28-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     TOSHIBA THNSNK128GVN8 M.2 2280 128GB
Serial Number:    66CS10CSTQ9V
LU WWN Device Id: 5 00080d 9106ada79
Firmware Version: K8DA4101
User Capacity:    128,035,676,160 bytes [128 GB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    Solid State Device
Form Factor:      M.2
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   ACS-3 (minor revision not indicated)
SATA Version is:  SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Sun Mar 29 04:21:10 2020 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(  120) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 (   6) minutes.
SCT capabilities: 	       (0x003d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       100
  9 Power_On_Hours          0x0012   100   100   000    Old_age   Always       -       2498
 12 Power_Cycle_Count       0x0033   100   100   000    Pre-fail  Always       -       5195
166 Unknown_Attribute       0x0012   100   100   000    Old_age   Always       -       0
167 Unknown_Attribute       0x0022   100   100   000    Old_age   Always       -       3
168 Unknown_Attribute       0x0012   100   100   000    Old_age   Always       -       0
173 Unknown_Attribute       0x0012   178   178   000    Old_age   Always       -       0
175 Program_Fail_Count_Chip 0x0033   100   100   010    Pre-fail  Always       -       0
176 Erase_Fail_Count_Chip   0x0033   100   100   010    Pre-fail  Always       -       0
177 Wear_Leveling_Count     0x0033   078   078   010    Pre-fail  Always       -       0
178 Used_Rsvd_Blk_Cnt_Chip  0x0033   100   100   010    Pre-fail  Always       -       0
179 Used_Rsvd_Blk_Cnt_Tot   0x0033   100   100   010    Pre-fail  Always       -       100
180 Unused_Rsvd_Blk_Cnt_Tot 0x0033   100   100   010    Pre-fail  Always       -       100
181 Program_Fail_Cnt_Total  0x0033   100   100   010    Pre-fail  Always       -       100
182 Erase_Fail_Count_Total  0x0033   100   100   010    Pre-fail  Always       -       100
187 Reported_Uncorrect      0x0033   100   100   000    Pre-fail  Always       -       0
192 Power-Off_Retract_Count 0x0012   100   100   000    Old_age   Always       -       81
194 Temperature_Celsius     0x0022   049   021   000    Old_age   Always       -       51 (Min/Max 11/79)
195 Hardware_ECC_Recovered  0x002b   100   100   000    Pre-fail  Always       -       0
199 UDMA_CRC_Error_Count    0x0012   100   100   000    Old_age   Always       -       0
238 Unknown_Attribute       0x0032   078   078   010    Old_age   Always       -       0
241 Total_LBAs_Written      0x0013   100   100   000    Pre-fail  Always       -       258816
242 Total_LBAs_Read         0x0013   100   100   000    Pre-fail  Always       -       305238

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%      2405         -
# 2  Short offline       Completed without error       00%      2250         -
# 3  Short offline       Completed without error       00%      1895         -
# 4  Short offline       Completed without error       00%      1894         -
# 5  Short offline       Completed without error       00%      1595         -
# 6  Short offline       Completed without error       00%      1475         -
# 7  Short offline       Completed without error       00%      1283         -
# 8  Short offline       Completed without error       00%      1199         -
# 9  Short offline       Completed without error       00%      1110         -
#10  Short offline       Completed without error       00%       961         -
#11  Short offline       Completed without error       00%       755         -
#12  Short offline       Completed without error       00%       717         -
#13  Short offline       Completed without error       00%       303         -
#14  Short offline       Completed without error       00%       224         -
#15  Short offline       Completed without error       00%       123         -
#16  Short offline       Aborted by host               00%        65         -
#17  Short offline       Completed without error       00%        65         -
#18  Short offline       Completed without error       00%        51         -
#19  Short offline       Completed without error       00%         1         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

The most interesting section of output from

 dmseg 

is

[   19.562813] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4350-pcie for chip BCM4350/8
[   19.562972] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available
[   19.563246] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4350/8 wl0: Oct 22 2015 06:16:26 version 7.35.180.119 (r594535) FWID 01-e791c176
[   19.629282] input: DLL0704:01 06CB:76AE Mouse as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-7/i2c-DLL0704:01/0018:06CB:76AE.0001/input/input17
[   19.629607] input: DLL0704:01 06CB:76AE Touchpad as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-7/i2c-DLL0704:01/0018:06CB:76AE.0001/input/input18
[   19.630079] hid-generic 0018:06CB:76AE.0001: input,hidraw0: I2C HID v1.00 Mouse [DLL0704:01 06CB:76AE] on i2c-DLL0704:01
[   19.651345] brcmfmac 0000:3a:00.0 wlp58s0: renamed from wlan0
[   19.729372] input: DLL0704:01 06CB:76AE Touchpad as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-7/i2c-DLL0704:01/0018:06CB:76AE.0001/input/input21
[   19.729572] hid-multitouch 0018:06CB:76AE.0001: input,hidraw0: I2C HID v1.00 Mouse [DLL0704:01 06CB:76AE] on i2c-DLL0704:01
[   20.284001] ACPI: Invalid package element [0]: got number, expecting [R]
[   20.284003] _ART package 0 is invalid, ignored
[   20.284020] ACPI: Invalid package element [0]: got number, expecting [R]
[   20.284021] _ART package 0 is invalid, ignored
[   20.446443] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   20.446445] Bluetooth: BNEP filters: protocol multicast
[   20.446449] Bluetooth: BNEP socket layer initialized
[   22.238580] audit: type=1400 audit(1585454348.521:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/snapd/snap-confine" pid=1719 comm="apparmor_parser"
[   22.238801] audit: type=1400 audit(1585454348.521:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/snapd/snap-confine//mount-namespace-capture-helper" pid=1719 comm="apparmor_parser"
[   27.352493] Bluetooth: RFCOMM TTY layer initialized
[   27.352499] Bluetooth: RFCOMM socket layer initialized
[   27.352505] Bluetooth: RFCOMM ver 1.11
[   30.706194] ACPI BIOS Error (bug): Failure creating named object [\_GPE._E42.SPRT], AE_ALREADY_EXISTS (20190703/dswload2-324)
[   30.706238] No Local Variables are initialized for Method [_E42]
[   30.706245] No Arguments are initialized for method [_E42]
[   30.706252] ACPI Error: AE_ALREADY_EXISTS, During name lookup/catalog (20190703/psobject-221)
[   30.706266] ACPI Error: Aborting method \_GPE._E42 due to previous error (AE_ALREADY_EXISTS) (20190703/psparse-531)
[   30.706284] ACPI Error: Aborting method \_GPE._E42 due to previous error (AE_ALREADY_EXISTS) (20190703/psparse-531)
[   30.706310] ACPI Error: AE_ALREADY_EXISTS, while evaluating GPE method [_E42] (20190703/evgpe-515)
seth wrote:

What we can say is that a disk showing this behavior is no more trustworthy.

Is there any hope for restoring this drive? Or is a full replacement necessary. (I have everything backed up already.) Thanks for your help and advice.

Offline

#9 2020-03-29 06:54:27

seth
Member
Registered: 2012-09-03
Posts: 58,672

Re: cannot run smartctl on drive

There's nothig interesting or disk IO related in that dmesg snippet at all, please don't post random excerpts.
There're no errors logged in the smartctl output and the last (short) test ran w/o errors ~100h ago.
The reallocated sector count is scary, but the numbers are often all over the place w/ SSDs anyway.

Please open a new thread, describe your actual error symptoms, post a complete dmesg. If you believe this is a drive issue, run a full SMART test and post the updated status report.

Online

#10 2020-03-29 10:34:25

WorMzy
Administrator
From: Scotland
Registered: 2010-06-16
Posts: 12,399
Website

Re: cannot run smartctl on drive

As seth says, please open a new topic for your issue.

https://wiki.archlinux.org/index.php/Co … bumping%22

Closing.


Sakura:-
Mobo: MSI MAG X570S TORPEDO MAX // Processor: AMD Ryzen 9 5950X @4.9GHz // GFX: AMD Radeon RX 5700 XT // RAM: 32GB (4x 8GB) Corsair DDR4 (@ 3000MHz) // Storage: 1x 3TB HDD, 6x 1TB SSD, 2x 120GB SSD, 1x 275GB M2 SSD

Making lemonade from lemons since 2015.

Offline

Board footer

Powered by FluxBB